The oxidation of two phase Cu Cr alloys containing 25% and 50% Cr prepared by powder metallurgy (PM) with a rather uniform two phase microstructure has been studied at 700～900 ℃ under oxygen pressure below the stabi...The oxidation of two phase Cu Cr alloys containing 25% and 50% Cr prepared by powder metallurgy (PM) with a rather uniform two phase microstructure has been studied at 700～900 ℃ under oxygen pressure below the stability of the copper oxides. The two PM alloys oxidized very slowly and formed only external Cr 2O 3 scales rather than undergoing an internal oxidation of chromium. This result is attributed mainly to a supply of chromium from the small Cr rich particles dispersed within the Cu rich phase. The oxidation kinetics of the two PM Cu Cr alloys approximately followed the parabolic rate law. The scaling rates are of the same order as those measured for pure chromium under the same oxygen pressure, but smaller than those for the alloys of similar composition prepared by normal arc melting techniques, whose compositions were largely non uniform. The results are interpreted in terms of the two phase nature of these alloys.展开更多
A new method for measuring the solid flow rate in gas solid two phase flow is introduced in this paper. An electrically heated probe was put in a gas solid two phase flow. For certain solid particles, the flow medi...A new method for measuring the solid flow rate in gas solid two phase flow is introduced in this paper. An electrically heated probe was put in a gas solid two phase flow. For certain solid particles, the flow media with different velocities and concentrations of particles produced different effects on heat transfer with the probe. The solid flow rate can be measured according to the intensity of heat transfer. Experiments were made on a pilot pneumatic conveying device. Research results prove that the method works effectively and reliably.展开更多
Theoretical and experimental study has been performed on heat transfer of airwater two phase laminar annular flow through a uniformly heated vertical small tube. Analysis ascertains that the mechanism of heat transfer...Theoretical and experimental study has been performed on heat transfer of airwater two phase laminar annular flow through a uniformly heated vertical small tube. Analysis ascertains that the mechanism of heat transfer is the evaporation of a very thin liquid film attached on the tube wall. The predictions of analytical solutions are quite good compared with the experimental results.展开更多
The indirect detection method basic principle of rate and concentration,application range and research results on gassolid two phase flow were discussed.The present development situation and the existing problems of r...The indirect detection method basic principle of rate and concentration,application range and research results on gassolid two phase flow were discussed.The present development situation and the existing problems of rate and concentration detection technology were analyzed and summarized.Emphatically analyzed the existing problems in the industrial application and research status of electrostatic method in measuring phase concentration.Design criterion of electrostatic phase concentration sensor is given,the superiority and wide industrial application prospect of the sensor used for phase concentration measurement are clarified.展开更多
The stability equation of interface of moving two phase jet and the corresponding equation of particle gas disturbance velocity ration are derived by means of the continuum phase coupling model. The stability curve...The stability equation of interface of moving two phase jet and the corresponding equation of particle gas disturbance velocity ration are derived by means of the continuum phase coupling model. The stability curves of interface of moving two phase jet for different particle properties and velocities of jetting device are given out through numerical computation. Further, sevral important conclusions on the effect of particle property and velocity of jetting device on the growth and propagation of disturbance of interface of moving two phase jet are reched on the basis of analyses of the obtained stability curves. These important conclusions can play a guiding role in studying development of moving two phase jet and executing artificial controls over it in practice.展开更多
Retrograde condensation frequently occurs during the development of gas condensate reservoirs. The loss of productivity is often observed due to the reduced relative permeability to gas as condensate accumulates ne...Retrograde condensation frequently occurs during the development of gas condensate reservoirs. The loss of productivity is often observed due to the reduced relative permeability to gas as condensate accumulates near the well bore region. How to describe the condensate blockage effect exactly has been a continuous research topic. However, up to now, the present methods usually over-estimate or underestimate the productivity reduction due to an incorrect understanding of the mechanism of flow in porous medium, which inevitably results in an inaccurate prediction of production performance. It has been found in recent numerous theoretical and experimental studies that capillary number and non-Darcy flow have significant influence on relative permeability in regions near the well bore. The two effects impose opposite impacts on production performance, thus leading to gas condensate flow showing characteristics different from general understanding. It is significant for prediction of performance in gas condensate wells to understand the two effects exactly. The aim of the paper is to describe and analyze the flow dynamics in porous media accurately during the production of gas condensate reservoirs. Based on the description of three-zone flow mechanism, capillary number and non-Darcy effect are incorporated in the analysis of relative permeability, making it possible to describe the effect of condensate blockage. The effect of capillary number and inertial flow on gas and condensate relative permeability is analyzed in detail. Novel Inflow Performance Relation (IPR) models considering high velocity effects are formulated and the contrast analysis of different IPR models is conducted. The result shows that the proposed method can help predict the production performance and productivity more accurately than conventional methods.展开更多
The two fluid model of stratified turbulent two phase flow in aquatic environment is developed in this paper. The motion of each phase is described by a unified multi fluid model in an Eulerian coordinate system. T...The two fluid model of stratified turbulent two phase flow in aquatic environment is developed in this paper. The motion of each phase is described by a unified multi fluid model in an Eulerian coordinate system. The laws of turbulent transportation for each phase, and the restriction of each other between the two phases are completely simulated. The complex two phase turbulence with strong buoyancy effects is selected to examine numerically. The extensive experimental data obtained in stratified flow are used here. Comparison of the results of numerical simulation with the experimental data is conducted. It has shown that the results of numerical simulation are satisfactory.展开更多
This paper deal with the frictional resistance characteristics of gas liquid two phase flow in vertical upward helical coiled tubes under the system pressure 0.1 0.6MPa. By means of dimension analysis and π theo...This paper deal with the frictional resistance characteristics of gas liquid two phase flow in vertical upward helical coiled tubes under the system pressure 0.1 0.6MPa. By means of dimension analysis and π theorem, the correlation formulas were obtained for calculating the frictional resistance coefficients of gas liquid two phase flow in helical coiled tubes. The calculated results agree well with the experimental results.展开更多
Multi-fluid k-e-kp, two phase turbulence model is used to simulate charged gas-liquid two phase coaxial jet, which is the transorting flow field in electrostatic spraying. Compared with the results of experiment, cha...Multi-fluid k-e-kp, two phase turbulence model is used to simulate charged gas-liquid two phase coaxial jet, which is the transorting flow field in electrostatic spraying. Compared with the results of experiment, charged gas-liquid two-phase turbulence can be well predicted by this model.展开更多
The flow with solid-liquid two-phase media inside centrifugal pumps is very complicated and the relevant method for the hydraulic design is still immature so far. There exist two main problems in the operation of the ...The flow with solid-liquid two-phase media inside centrifugal pumps is very complicated and the relevant method for the hydraulic design is still immature so far. There exist two main problems in the operation of the two-phase flow pumps, i.e., low overall efficiency and severe abrasion. In this study, the three-dimensional, steady, incompressible, and turbulent solid-liquid two-phase flows in a low-specific-speed centrifugal pump are numerically simulated and analyzed by using a computational fluid dynamics （CFD） code based on the mixture model of the two-phase flow and the RNG k-~ two-equation turbulence model, in which the influences of rotation and curvature are fully taken into account. The coupling between impeller and volute is implemented by means of the frozen rotor method. The simulation results predicted indicate that the solid phase properties in two-phase flow, especially the concentration, the particle diameter and the density, have strong effects on the hydraulic performance of the pump. Both the pump head and the efficiency are reduced with increasing particle diameter or concentration. However, the effect of particle density on the performance is relatively minor. An obvious jet-wake flow structure is presented near the volute tongue and becomes more remarkable with increasing solid phase concentration. The suction side of the blade is subject to much more severe abrasion than the pressure side. The obtained results preliminarily reveal the characteristics of solid-liquid two-phase flow in the centrifugal pump, and are helpful for improvement and empirical correction in the hydraulic design of centrifugal pumps.展开更多
The cormsion in air of a two-phase Cu-75Cr alloy was studied at 700-900℃. Thealloy cormded nearly parabolically at 700-800℃, but at 900℃ its instantaneousparabolic mte constant decreased with time. The scales were ...The cormsion in air of a two-phase Cu-75Cr alloy was studied at 700-900℃. Thealloy cormded nearly parabolically at 700-800℃, but at 900℃ its instantaneousparabolic mte constant decreased with time. The scales were complex and consistedof an outermost layer of copper oxide generally followed bg a layer of the double ox-ide Cu2 Cr2 O4 sometimes containing particles of unoxidized chromium surmunded bya chromia layer. An innermost layer of chromia was also observed in some cases.Finally metallic copper was al8o frequently mixed with chromia particles. No Cr de-pletion was observed in the alloy close to the inteffoce with the scale. In any case,this alloy was not able to form an exclusive continuous protective chromia layer. Thespecial cormsion behavior Of this alloy is typical of two-phase binary systems with alange solubility gaP in which the outwaof dthesion fiux of the most-reactive componentin the alloy is strongly reduced and may be inswncient to fOrm a protective externallayer of the cormsponding oxide. In paTticular, the presence of particles of Cr withina double oxide layer is very unusual and is allowed only for the kinetic reason.展开更多
The effect of grain size reduction on the high temperature oxidation of binary two phase alloys was discussed based on the recent research progress. The results show that for those two phase alloys with coarse grain p...The effect of grain size reduction on the high temperature oxidation of binary two phase alloys was discussed based on the recent research progress. The results show that for those two phase alloys with coarse grain prepared by the conventional methods, complex oxide scales are easily formed after oxidation under high oxygen pressure or under oxygen pressure below the stability limit of the less reactive component oxides. On the contrary, for the nano sized alloys, an exclusive external oxidation of the most reactive component usually occurs during oxidation in air or pure oxygen even for much lower content of the most reactive component. So the gain size reduction is not always beneficial to improve the oxidation resistance of the materials, but exhibits different effects depending mainly on the protective feature of the scales. The transition mechanisms between the different oxidation modes are discussed with respect to the thermodynamic and dynamic aspects.展开更多
Measurement of two phase flow in porous medium for sequestration was carried out using high-resolution magnetic resonance imaging (MRI) technique. The porous medium was a packed bed of glass beads. Spin echo multi seq...Measurement of two phase flow in porous medium for sequestration was carried out using high-resolution magnetic resonance imaging (MRI) technique. The porous medium was a packed bed of glass beads. Spin echo multi sequence was used to measure the distribution of CO2 and water in the porous medium. The intensity images show that the fluid distribution is non-uniform due to its viscosity and pore structure of porous medium. The velocity distribution of fluids is calculated from the saturation of water and porosity of porous medium. The experimental results show that fluid velocities vary with time and position. The capillary dispersion rate donated the effects of capillary, which was largest at water saturations of 0.45. The displacement process is different between in BZ-02 and BZ-2. The final water residual saturation depends on permeability and porosity.展开更多
The transient behavior of centrifugal pumps during transient operating periods, such as startup and stopping, has drawn more and more attention recently because of urgent needs in engineering. Up to now, almost all th...The transient behavior of centrifugal pumps during transient operating periods, such as startup and stopping, has drawn more and more attention recently because of urgent needs in engineering. Up to now, almost all the existing studies on this behavior are limited to using water as working fluid. The study on the transient behavior related to solid-liquid two-phase flow has not been seen yet. In order to explore the transient characteristics of a high specific-speed centrifugal pump during startup period delivering the pure water and solid-liquid two-phase flow, the transient flows inside the pump are numerically simulated using the dynamic mesh method. The variable rotational speed and flow rate with time obtained from experiment are best fitted as the function of time, and are written into computational fluid dynamics （CFD） code-FLUENT by using a user defined function. The predicted heads are compared with experimental results when pumping pure water. The results show that the difference in the transient performance during startup period is very obvious between water and solid-liquid two-phase flow during the later stage of startup process. Moreover, the time for the solid-liquid two-phase flow to achieve a stable condition is longer than that for water. The solid-liquid two-phase flow results in a higher impeller shaft power, a larger dynamic reaction force, a more violent fluctuation in pressure and a reduced stable pressure rise comparing with water. The research may be useful to tmderstanding on the transient behavior of a centrifugal pump under a solid-liquid two-phase flow during startup period.展开更多
A new anaerobic reactor, Jet-loop anaerobic fluidized bed （JLAFB）, was designed for treating high-sulfate wastewater. The treatment characteristics, including the effect of influent COD/SO42 ratio and alkalinity and...A new anaerobic reactor, Jet-loop anaerobic fluidized bed （JLAFB）, was designed for treating high-sulfate wastewater. The treatment characteristics, including the effect of influent COD/SO42 ratio and alkalinity and sulfide inhibition in reactors, were discussed for a JLAFB and a general anaerobic fiuidized bed （AFB） reactor used as sulfate-reducing phase and methane-producing phase, respectively, in two-phase anaerobic digestion process. The formation of granules in the two reactors was also examined. The results indicated that COD and sulfate removal had different demand of influent COD/SO4^2- ratios. When total COD removal was up to 85%, the ratio was only required up to 1.2, whereas, total sulfate removal up to 95% required it exceeding 3.0. The alkalinity in the two reactors increased linearly with the growth of influent alkalinity. Moreover, the change of influent alkalinity had no significant effect on pH and volatile fatty acids （VFA） in the two reactors. Influent alkalinity kept at 400-500 mg/L could meet the requirement of the treating process. The JLAFB reactor had great advantage in avoiding sulfide and free-H2S accumulation and toxicity inhibition on microorganisms. When sulfate loading rate was up to 8. 1 kg/（m^3.d）, the sulfide and free-H2S concentrations in JLAFB reactor were 58.6 and 49.7 mg/L, respectively. Furthermore, the granules, with offwhite color, ellipse shape and diameters of 1.0-3.0 mm, could be developed in JLAFB reactor. In granules, different groups of bacteria were distributed in different layers, and some inorganic metal compounds such as Fe, Ca, Mg etc. were found.展开更多
A second-order moment two-phase turbulence model for simulating dense gas-particle flows （USM-Θ model）, combining the unified second-order moment twophase turbulence model for dilute gas-particle flows with the kin...A second-order moment two-phase turbulence model for simulating dense gas-particle flows （USM-Θ model）, combining the unified second-order moment twophase turbulence model for dilute gas-particle flows with the kinetic theory of particle collision, is proposed. The interaction between gas and particle turbulence is simulated using the transport equation of two-phase velocity correlation with a two-time-scale dissipation closure. The proposed model is applied to simulate dense gas-particle flows in a horizontal channel and a downer. Simulation results and their comparison with experimental results show that the model accounting for both anisotropic particle turbulence and particle-particle collision is obviously better than models accounting for only particle turbulence or only particle-particle collision. The USM-Θ model is also better than the k-ε-kp-Θ model and the k-ε-kp-εp-Θ model in that the first model can simulate the redistribution of anisotropic particle Reynolds stress components due to inter-particle collision, whereas the second and third models cannot.展开更多
Based on the Biot＇s theory about two-phase saturated medium, according to the character of δ function, the Green function on two-phase saturated medium by the point source under concentrated force can be derived. By...Based on the Biot＇s theory about two-phase saturated medium, according to the character of δ function, the Green function on two-phase saturated medium by the point source under concentrated force can be derived. By the Betti＇s theorem for the two-phase saturated medium field, the source vector and static displacement field by elastic dislocation on the two-phase saturated medium were comprehensively discussed.展开更多
Partition coefficients of Urokinase(UK)were measured in aqueous two-phase systems con-taining polyethylene glycol and potassium phosphate at 273.2K.Based on the Diamond-Hsu model,a modified expression was obtained for...Partition coefficients of Urokinase(UK)were measured in aqueous two-phase systems con-taining polyethylene glycol and potassium phosphate at 273.2K.Based on the Diamond-Hsu model,a modified expression was obtained for the correlation of enzyme partitioning in theabove-mentioned systems.Utilizing a modified form,the partitioning data of UK and heteroproteinwere correlated.The results show that the modified model is simple gives good precision.and will fa-cilitate engineering scale-up of aqueous two-phase systems for certain proteins purification.展开更多
A mathematical model is set to evaluate the 3-D dense solid-liquid two-phaseturbulent flow in a non-clogging mud pump, the flow feature in the impeller channel is simulatedwith the tool of IPSA. Meanwhile, resort to T...A mathematical model is set to evaluate the 3-D dense solid-liquid two-phaseturbulent flow in a non-clogging mud pump, the flow feature in the impeller channel is simulatedwith the tool of IPSA. Meanwhile, resort to TECPLOT as the post-processor, the simulation results isvisualized. The results show the main flow characteristics: There exists backflow and aberrantvelocities at inlet area and a relative velocity slip between two phases; A jet-wake flow pattern isdiscerned around the shroud-suction side area; The relative velocity vector of solid phase iscloser to the pressure surface than that of liquid phase and the trend is more obvious with theincrease of diameter; The kinetic energy of turbulence k and the dissipation rate e reach theirpeaks at the corner of pressure and suction surface. The simulation results show a good agreementwith the experimental flow features in the impeller channel, which prove the turbulent model used isvalid and provide a theoretical design basis to non-clogging pumps.展开更多
The interesting phenopmena of two aqueous phases coexisting in dilute aqueous solutions of sodium undecenoate-dodecyltrimethylammo brodride ndxture and sodium laurate-dodecyltrimethylammonium brondde mixture were inve...The interesting phenopmena of two aqueous phases coexisting in dilute aqueous solutions of sodium undecenoate-dodecyltrimethylammo brodride ndxture and sodium laurate-dodecyltrimethylammonium brondde mixture were investigated. Vesicles existing in both phases were shown by TEM images. The vesicles are dispersed in lower phase and flocculated in upper phase. Multilamellar structure of vesicles was found in the upper phase of sodium laurate-dodecyltrimethylammonium bromide system.展开更多
文摘The oxidation of two phase Cu Cr alloys containing 25% and 50% Cr prepared by powder metallurgy (PM) with a rather uniform two phase microstructure has been studied at 700～900 ℃ under oxygen pressure below the stability of the copper oxides. The two PM alloys oxidized very slowly and formed only external Cr 2O 3 scales rather than undergoing an internal oxidation of chromium. This result is attributed mainly to a supply of chromium from the small Cr rich particles dispersed within the Cu rich phase. The oxidation kinetics of the two PM Cu Cr alloys approximately followed the parabolic rate law. The scaling rates are of the same order as those measured for pure chromium under the same oxygen pressure, but smaller than those for the alloys of similar composition prepared by normal arc melting techniques, whose compositions were largely non uniform. The results are interpreted in terms of the two phase nature of these alloys.
文摘A new method for measuring the solid flow rate in gas solid two phase flow is introduced in this paper. An electrically heated probe was put in a gas solid two phase flow. For certain solid particles, the flow media with different velocities and concentrations of particles produced different effects on heat transfer with the probe. The solid flow rate can be measured according to the intensity of heat transfer. Experiments were made on a pilot pneumatic conveying device. Research results prove that the method works effectively and reliably.
文摘Theoretical and experimental study has been performed on heat transfer of airwater two phase laminar annular flow through a uniformly heated vertical small tube. Analysis ascertains that the mechanism of heat transfer is the evaporation of a very thin liquid film attached on the tube wall. The predictions of analytical solutions are quite good compared with the experimental results.
基金Science and Technology on Electronic Test and Measurement Laboratory(No.9140C12040515X)
文摘The indirect detection method basic principle of rate and concentration,application range and research results on gassolid two phase flow were discussed.The present development situation and the existing problems of rate and concentration detection technology were analyzed and summarized.Emphatically analyzed the existing problems in the industrial application and research status of electrostatic method in measuring phase concentration.Design criterion of electrostatic phase concentration sensor is given,the superiority and wide industrial application prospect of the sensor used for phase concentration measurement are clarified.
文摘The stability equation of interface of moving two phase jet and the corresponding equation of particle gas disturbance velocity ration are derived by means of the continuum phase coupling model. The stability curves of interface of moving two phase jet for different particle properties and velocities of jetting device are given out through numerical computation. Further, sevral important conclusions on the effect of particle property and velocity of jetting device on the growth and propagation of disturbance of interface of moving two phase jet are reched on the basis of analyses of the obtained stability curves. These important conclusions can play a guiding role in studying development of moving two phase jet and executing artificial controls over it in practice.
基金Project“973",a national fundamental research development program
文摘Retrograde condensation frequently occurs during the development of gas condensate reservoirs. The loss of productivity is often observed due to the reduced relative permeability to gas as condensate accumulates near the well bore region. How to describe the condensate blockage effect exactly has been a continuous research topic. However, up to now, the present methods usually over-estimate or underestimate the productivity reduction due to an incorrect understanding of the mechanism of flow in porous medium, which inevitably results in an inaccurate prediction of production performance. It has been found in recent numerous theoretical and experimental studies that capillary number and non-Darcy flow have significant influence on relative permeability in regions near the well bore. The two effects impose opposite impacts on production performance, thus leading to gas condensate flow showing characteristics different from general understanding. It is significant for prediction of performance in gas condensate wells to understand the two effects exactly. The aim of the paper is to describe and analyze the flow dynamics in porous media accurately during the production of gas condensate reservoirs. Based on the description of three-zone flow mechanism, capillary number and non-Darcy effect are incorporated in the analysis of relative permeability, making it possible to describe the effect of condensate blockage. The effect of capillary number and inertial flow on gas and condensate relative permeability is analyzed in detail. Novel Inflow Performance Relation (IPR) models considering high velocity effects are formulated and the contrast analysis of different IPR models is conducted. The result shows that the proposed method can help predict the production performance and productivity more accurately than conventional methods.
文摘The two fluid model of stratified turbulent two phase flow in aquatic environment is developed in this paper. The motion of each phase is described by a unified multi fluid model in an Eulerian coordinate system. The laws of turbulent transportation for each phase, and the restriction of each other between the two phases are completely simulated. The complex two phase turbulence with strong buoyancy effects is selected to examine numerically. The extensive experimental data obtained in stratified flow are used here. Comparison of the results of numerical simulation with the experimental data is conducted. It has shown that the results of numerical simulation are satisfactory.
文摘This paper deal with the frictional resistance characteristics of gas liquid two phase flow in vertical upward helical coiled tubes under the system pressure 0.1 0.6MPa. By means of dimension analysis and π theorem, the correlation formulas were obtained for calculating the frictional resistance coefficients of gas liquid two phase flow in helical coiled tubes. The calculated results agree well with the experimental results.
基金This project is supported by Provincial Basic Application Granting of Jiangsu(No. B197063
文摘Multi-fluid k-e-kp, two phase turbulence model is used to simulate charged gas-liquid two phase coaxial jet, which is the transorting flow field in electrostatic spraying. Compared with the results of experiment, charged gas-liquid two-phase turbulence can be well predicted by this model.
基金supported by National Natural Science Foundation of China (Grant No. 21076198)Zhejiang Provincial Natural Science Foundation of China (Granted No. R1100530)National Basic Research Program of China (973 Program,Grant No. 2009CB724303)
文摘The flow with solid-liquid two-phase media inside centrifugal pumps is very complicated and the relevant method for the hydraulic design is still immature so far. There exist two main problems in the operation of the two-phase flow pumps, i.e., low overall efficiency and severe abrasion. In this study, the three-dimensional, steady, incompressible, and turbulent solid-liquid two-phase flows in a low-specific-speed centrifugal pump are numerically simulated and analyzed by using a computational fluid dynamics （CFD） code based on the mixture model of the two-phase flow and the RNG k-~ two-equation turbulence model, in which the influences of rotation and curvature are fully taken into account. The coupling between impeller and volute is implemented by means of the frozen rotor method. The simulation results predicted indicate that the solid phase properties in two-phase flow, especially the concentration, the particle diameter and the density, have strong effects on the hydraulic performance of the pump. Both the pump head and the efficiency are reduced with increasing particle diameter or concentration. However, the effect of particle density on the performance is relatively minor. An obvious jet-wake flow structure is presented near the volute tongue and becomes more remarkable with increasing solid phase concentration. The suction side of the blade is subject to much more severe abrasion than the pressure side. The obtained results preliminarily reveal the characteristics of solid-liquid two-phase flow in the centrifugal pump, and are helpful for improvement and empirical correction in the hydraulic design of centrifugal pumps.
文摘The cormsion in air of a two-phase Cu-75Cr alloy was studied at 700-900℃. Thealloy cormded nearly parabolically at 700-800℃, but at 900℃ its instantaneousparabolic mte constant decreased with time. The scales were complex and consistedof an outermost layer of copper oxide generally followed bg a layer of the double ox-ide Cu2 Cr2 O4 sometimes containing particles of unoxidized chromium surmunded bya chromia layer. An innermost layer of chromia was also observed in some cases.Finally metallic copper was al8o frequently mixed with chromia particles. No Cr de-pletion was observed in the alloy close to the inteffoce with the scale. In any case,this alloy was not able to form an exclusive continuous protective chromia layer. Thespecial cormsion behavior Of this alloy is typical of two-phase binary systems with alange solubility gaP in which the outwaof dthesion fiux of the most-reactive componentin the alloy is strongly reduced and may be inswncient to fOrm a protective externallayer of the cormsponding oxide. In paTticular, the presence of particles of Cr withina double oxide layer is very unusual and is allowed only for the kinetic reason.
文摘The effect of grain size reduction on the high temperature oxidation of binary two phase alloys was discussed based on the recent research progress. The results show that for those two phase alloys with coarse grain prepared by the conventional methods, complex oxide scales are easily formed after oxidation under high oxygen pressure or under oxygen pressure below the stability limit of the less reactive component oxides. On the contrary, for the nano sized alloys, an exclusive external oxidation of the most reactive component usually occurs during oxidation in air or pure oxygen even for much lower content of the most reactive component. So the gain size reduction is not always beneficial to improve the oxidation resistance of the materials, but exhibits different effects depending mainly on the protective feature of the scales. The transition mechanisms between the different oxidation modes are discussed with respect to the thermodynamic and dynamic aspects.
基金Supported by the Major State Basic Research Development Program of China(2011CB707304)the National Natural Science Foundation of China(51006016,51006017,51106018,51106019)
文摘Measurement of two phase flow in porous medium for sequestration was carried out using high-resolution magnetic resonance imaging (MRI) technique. The porous medium was a packed bed of glass beads. Spin echo multi sequence was used to measure the distribution of CO2 and water in the porous medium. The intensity images show that the fluid distribution is non-uniform due to its viscosity and pore structure of porous medium. The velocity distribution of fluids is calculated from the saturation of water and porosity of porous medium. The experimental results show that fluid velocities vary with time and position. The capillary dispersion rate donated the effects of capillary, which was largest at water saturations of 0.45. The displacement process is different between in BZ-02 and BZ-2. The final water residual saturation depends on permeability and porosity.
基金supported by National Natural Science Foundation of China(Grant Nos.51076144,51276172)Zhejiang Provincial Natural Science Foundation of China(Grant Nos.R1100530,LY12E06002)National Basic Research Program of China(973 Program,Grant No.2009CB724303)
文摘The transient behavior of centrifugal pumps during transient operating periods, such as startup and stopping, has drawn more and more attention recently because of urgent needs in engineering. Up to now, almost all the existing studies on this behavior are limited to using water as working fluid. The study on the transient behavior related to solid-liquid two-phase flow has not been seen yet. In order to explore the transient characteristics of a high specific-speed centrifugal pump during startup period delivering the pure water and solid-liquid two-phase flow, the transient flows inside the pump are numerically simulated using the dynamic mesh method. The variable rotational speed and flow rate with time obtained from experiment are best fitted as the function of time, and are written into computational fluid dynamics （CFD） code-FLUENT by using a user defined function. The predicted heads are compared with experimental results when pumping pure water. The results show that the difference in the transient performance during startup period is very obvious between water and solid-liquid two-phase flow during the later stage of startup process. Moreover, the time for the solid-liquid two-phase flow to achieve a stable condition is longer than that for water. The solid-liquid two-phase flow results in a higher impeller shaft power, a larger dynamic reaction force, a more violent fluctuation in pressure and a reduced stable pressure rise comparing with water. The research may be useful to tmderstanding on the transient behavior of a centrifugal pump under a solid-liquid two-phase flow during startup period.
基金Project supported by the National Natural Science Foundation of China(No. 50278036)the Natural Science Foundation of Guangdong Province (No. 04105951)
文摘A new anaerobic reactor, Jet-loop anaerobic fluidized bed （JLAFB）, was designed for treating high-sulfate wastewater. The treatment characteristics, including the effect of influent COD/SO42 ratio and alkalinity and sulfide inhibition in reactors, were discussed for a JLAFB and a general anaerobic fiuidized bed （AFB） reactor used as sulfate-reducing phase and methane-producing phase, respectively, in two-phase anaerobic digestion process. The formation of granules in the two reactors was also examined. The results indicated that COD and sulfate removal had different demand of influent COD/SO4^2- ratios. When total COD removal was up to 85%, the ratio was only required up to 1.2, whereas, total sulfate removal up to 95% required it exceeding 3.0. The alkalinity in the two reactors increased linearly with the growth of influent alkalinity. Moreover, the change of influent alkalinity had no significant effect on pH and volatile fatty acids （VFA） in the two reactors. Influent alkalinity kept at 400-500 mg/L could meet the requirement of the treating process. The JLAFB reactor had great advantage in avoiding sulfide and free-H2S accumulation and toxicity inhibition on microorganisms. When sulfate loading rate was up to 8. 1 kg/（m^3.d）, the sulfide and free-H2S concentrations in JLAFB reactor were 58.6 and 49.7 mg/L, respectively. Furthermore, the granules, with offwhite color, ellipse shape and diameters of 1.0-3.0 mm, could be developed in JLAFB reactor. In granules, different groups of bacteria were distributed in different layers, and some inorganic metal compounds such as Fe, Ca, Mg etc. were found.
基金the Special Funds for Major State Basic Research of China(G-1999-0222-08)the National Natural Science Foundation of China(50376004)Ph.D.Program Foundation,Ministry of Education of China(20030007028)
文摘A second-order moment two-phase turbulence model for simulating dense gas-particle flows （USM-Θ model）, combining the unified second-order moment twophase turbulence model for dilute gas-particle flows with the kinetic theory of particle collision, is proposed. The interaction between gas and particle turbulence is simulated using the transport equation of two-phase velocity correlation with a two-time-scale dissipation closure. The proposed model is applied to simulate dense gas-particle flows in a horizontal channel and a downer. Simulation results and their comparison with experimental results show that the model accounting for both anisotropic particle turbulence and particle-particle collision is obviously better than models accounting for only particle turbulence or only particle-particle collision. The USM-Θ model is also better than the k-ε-kp-Θ model and the k-ε-kp-εp-Θ model in that the first model can simulate the redistribution of anisotropic particle Reynolds stress components due to inter-particle collision, whereas the second and third models cannot.
文摘Based on the Biot＇s theory about two-phase saturated medium, according to the character of δ function, the Green function on two-phase saturated medium by the point source under concentrated force can be derived. By the Betti＇s theorem for the two-phase saturated medium field, the source vector and static displacement field by elastic dislocation on the two-phase saturated medium were comprehensively discussed.
基金Supported by National Natural Science Foundation of China
文摘Partition coefficients of Urokinase(UK)were measured in aqueous two-phase systems con-taining polyethylene glycol and potassium phosphate at 273.2K.Based on the Diamond-Hsu model,a modified expression was obtained for the correlation of enzyme partitioning in theabove-mentioned systems.Utilizing a modified form,the partitioning data of UK and heteroproteinwere correlated.The results show that the modified model is simple gives good precision.and will fa-cilitate engineering scale-up of aqueous two-phase systems for certain proteins purification.
文摘A mathematical model is set to evaluate the 3-D dense solid-liquid two-phaseturbulent flow in a non-clogging mud pump, the flow feature in the impeller channel is simulatedwith the tool of IPSA. Meanwhile, resort to TECPLOT as the post-processor, the simulation results isvisualized. The results show the main flow characteristics: There exists backflow and aberrantvelocities at inlet area and a relative velocity slip between two phases; A jet-wake flow pattern isdiscerned around the shroud-suction side area; The relative velocity vector of solid phase iscloser to the pressure surface than that of liquid phase and the trend is more obvious with theincrease of diameter; The kinetic energy of turbulence k and the dissipation rate e reach theirpeaks at the corner of pressure and suction surface. The simulation results show a good agreementwith the experimental flow features in the impeller channel, which prove the turbulent model used isvalid and provide a theoretical design basis to non-clogging pumps.
文摘The interesting phenopmena of two aqueous phases coexisting in dilute aqueous solutions of sodium undecenoate-dodecyltrimethylammo brodride ndxture and sodium laurate-dodecyltrimethylammonium brondde mixture were investigated. Vesicles existing in both phases were shown by TEM images. The vesicles are dispersed in lower phase and flocculated in upper phase. Multilamellar structure of vesicles was found in the upper phase of sodium laurate-dodecyltrimethylammonium bromide system.
