Four types of seismic design details were tested using 11 transfer column specimens and one comparison specimen of RC under low cyclic reversed loading. Test results show that diagonal cracks control the failure patte...Four types of seismic design details were tested using 11 transfer column specimens and one comparison specimen of RC under low cyclic reversed loading. Test results show that diagonal cracks control the failure pattern and damage occurs mainly in the RC section with weak shear capacity in the transfer columns. There is a large difference in the bearing capacity and ductility of the transfer columns according to the test results, which indicates that the strengthening effect of diverse structural measures is quite different. The section ratio of I-section-encased steel and the axial compression ratio also have a great influence on the bearing capacity and ductility. Although the bearing capacity of transfer columns with additional longitudinal bars and additional X bars is relatively large, they have poor deformation capacity. Setting more stirrups along the columns is the best structural measure to enhance the seismic performance. The studs on the I-sectionencased steel by welding can help to complete the stress transfer between the steel and concrete, and avoid performance degradation of the two materials due to bonding failure.展开更多
Based on single drop mass transfer models and two phase flow equation,a general equationfor calculating the‘true’height of transfer unit of extraction columns was derived and tested withfour types of extraction colu...Based on single drop mass transfer models and two phase flow equation,a general equationfor calculating the‘true’height of transfer unit of extraction columns was derived and tested withfour types of extraction columns with some different working systems.The calculated results fittedwell with those obtained by experiments.展开更多
The effect of different surfactants(n-octyltrimethylammonium bromide(OTABr),sodium dodecyl benzene sulfonate(SDBS) and Tween 80) with different critical micelle concentrations(CMC) on the CO_2 absorption into aqueous ...The effect of different surfactants(n-octyltrimethylammonium bromide(OTABr),sodium dodecyl benzene sulfonate(SDBS) and Tween 80) with different critical micelle concentrations(CMC) on the CO_2 absorption into aqueous solutions in a bubble column is analyzed in the present work.The presence of these surfactants increased the gas-liquid interfacial area,and decreased the liquid phase mass transfer coefficient,but with significant different extent.The results indicated that the CMC can be a key parameter affecting the mass transfer of CO_2 absorption into a dilute aqueous solution of a surfactant.Sardeing's model was used to fit the experimental data successfully by re-correlating the parameters.展开更多
The volumetric overall mass transfer coefficients in a multistage column have been measured using axial dispersion model for toluene–acetone–water system. The effect of operating parameters on the volumetric overall...The volumetric overall mass transfer coefficients in a multistage column have been measured using axial dispersion model for toluene–acetone–water system. The effect of operating parameters on the volumetric overall mass transfer coefficients has been investigated for both mass transfer directions. The results show that the mass transfer performance is strongly dependent on rotor speed and mass transfer direction, although only slightly dependent on phase flow rates. In addition, empirical correlations to predict the overall mass transfer coefficients have been developed. The proposed correlations based on dimensionless numbers can be considered as a useful tool for the possible scale up of the multistage column extractor.展开更多
To make more homogenous organic monolithic structure, reversible addition-fragmentation chain transfer （RAFT） process was employed in the synthesis of the clenbuterol imprinted polymer. In the synthesis, the influen...To make more homogenous organic monolithic structure, reversible addition-fragmentation chain transfer （RAFT） process was employed in the synthesis of the clenbuterol imprinted polymer. In the synthesis, the influence of synthetic conditions on the polymer structure and separation efficiency was studied. The result demonstrated that the imprinted columns prepared with RAFT process have higher column efficiency and selectivity than the columns prepared with conventional polymerization in the present study, which may result from the higher surface area, smaller pore size and the narrower globule size distribution in their structures. The result indicated that RAFT polymerization provided better conditions for the clenbuterol imprinted monolithic polymer preparation. 2009 Xiang Chao Dong. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.展开更多
This paper investigates the thermal-coupled effect across the wall and the optimal heat transfer region of the wall for enhancing the energy saving effect of dividing wall column (DWC), and also studies the effects of...This paper investigates the thermal-coupled effect across the wall and the optimal heat transfer region of the wall for enhancing the energy saving effect of dividing wall column (DWC), and also studies the effects of feed thermal condition (q) and middle component composition of feed (cB) on the heat transfer process, the optimal heat transfer region, and the maximum heat transfer quantity across the wall. The simulation results show that the maximum heat transfer quantity across the wall and the potential for energy saving increase with the increase of q, while with the limitation of temperature difference across the wall, the beneficial heat transfer effect between certain range of stages, which are involved in the optimal heat transfer region, cannot be realized completely for a specific value of q. Besides, compared with q, a changing cB does not change the degree of realizing the beneficial heat transfer effect, but can bring about the variation of liquid split ratio (RL) and vapor split ratio (Rv). Thus, for achieving a maximum energy-saving effect of DWC, different q and cB need to find its own corresponding suitable heat transfer process across the wall.展开更多
Heat transfer and bubble phenomena were investigated by adopting the drift flux model in a viscous slurry bubble column reactor (SBCR), having a diameter of 0.0508 m(ID) and height 1.5 m. The effects of superficial ga...Heat transfer and bubble phenomena were investigated by adopting the drift flux model in a viscous slurry bubble column reactor (SBCR), having a diameter of 0.0508 m(ID) and height 1.5 m. The effects of superficial gas velocity (0.002 -0.164 m/s), solid concentration (0 - 20 wt%) and liquid viscosity (paraffin oil;16.9 mPa•s and squalane;25.9 mPa•s) on the gas holdup and heat transfer characteristics were examined. It was observed that the gas holdup increased with increasing superficial gas velocity (UG), but decreased with increasing solid concentration (SC) or slurry viscosity. The degree of non-uniformity in a SBCR could be determined by the modified drift flux model at the heterogeneous flow regime. The local heat transfer coefficient (h) between the immersed heater and the bed decreased with increasing liquid viscosity and SC, but it increased with increasing UG. The modified Nusselt number including the gas holdup and local heat transfer coefficient was well correlated in terms of dimensionless groups such as Reynolds and Prandtl numbers.展开更多
Hydrodynamics and mass transfer experiments were carried out in a 0.1m diameter extraction column with a new type (FG) stack packing developed recently in our laboratory.The working systems used were n-Butano1/Succini...Hydrodynamics and mass transfer experiments were carried out in a 0.1m diameter extraction column with a new type (FG) stack packing developed recently in our laboratory.The working systems used were n-Butano1/Succinic acid/water with low interfacial tension of 1.50×10-3N·m-1 and 30% TBP (Kerosene)/Acetic acid/water with interfacial tension of 10.0×10-3N· m-1. Experimental results obtained indicated that (FG) stack packed extraction column was proved to possess high throughput capacity and excellent mass transfer efficiency. Replacing rotary discs with FG packings in a lube furfural extraction tower was quite success with significant economical benefits being claimed.展开更多
The axial mixing is a key factor for design and scaling up of the pulsed extraction column which has strong influence on the mass transfer performances of the pulsed extraction column with discs and doughnuts. A stead...The axial mixing is a key factor for design and scaling up of the pulsed extraction column which has strong influence on the mass transfer performances of the pulsed extraction column with discs and doughnuts. A steady-state concentration profile measurement was used to evaluate the mass transfer and axial mixing coefficients for the nitric acid/water/30%TRPO (in kerosene) system in the pulsed extraction column with the diameter of 38 mm on the condition of the TRPO-kerosene solution as the continuous phase and the flow ratio of 1∶1. Experimental results indicate that Ey evaluated by the experiments is in good agreement with that given by Burratti’s correlation; the axial mixing is far smaller for the continuous phase than that for the dispersed phase. However the empirical correlation for HOX is only given based on the present data.展开更多
The variation in arc characteristics and behavior of metal transfer with the change in pulse parameters has been studied by high speed video camera during pulse current flux-cored arc weld deposition.A comparative stu...The variation in arc characteristics and behavior of metal transfer with the change in pulse parameters has been studied by high speed video camera during pulse current flux-cored arc weld deposition.A comparative study of similar nature has also been carried out during flux-cored arc weld deposition in globular and spray transfer modes.The effect of pulse parameters has been studied by considering their mean current and arc voltage.The arc characteristics studied by its root diameter,projected diameter and length,and the behavior of metal transfer noted by the metal transfer model and the droplet diameter have been found to vary significantly with the pulse parameters.The observation may help in understanding the arc characteristics with respect to the variation in pulse parameters which may be beneficial in using pulse current FCAW to produce desired weld quality.展开更多
Enhanced boiling experiments of two different enhanced structures were carried out in a thermosyphon loop evaporator chamber. One was micro-columns array structure (MCAS), which was fabricated on copper plate surface ...Enhanced boiling experiments of two different enhanced structures were carried out in a thermosyphon loop evaporator chamber. One was micro-columns array structure (MCAS), which was fabricated on copper plate surface with interaction high speed wire electrode discharge machining (HS-WEDM). The other was the ramification of MCAS, named micro-column-array and sintered-copper compound structure (MSCS), which was fabricated with sintered method on micro-column array structure. Considering the wall superheat and critical heat flux (CHF), comparisons were made between them. The results show that both MCAS and MSCS can enhance the boiling heat transfer. It is also found that the enhanced boiling heat transfer ability of MSCS is changed obviously while the porosity of the sintered copper layer is changed.展开更多
Correlations will be presented to describe liquid hold up, loading and flooding capacity, volumetric mass transfer coefficients on liquid and gas or vapour phase and the pressure drop as a basis for computing packed c...Correlations will be presented to describe liquid hold up, loading and flooding capacity, volumetric mass transfer coefficients on liquid and gas or vapour phase and the pressure drop as a basis for computing packed columns, dumped and regular as well, including the influence of end effects on scaling. The relationships are found on a sound physical and mathematical basis and their validity were confirmed by experimental investigations of many packings; some of them were selected to be considered in this work.展开更多
This paper presents a comprehensive review of various traditional systems of crude oil distillation column design, modeling, simulation, optimization and control methods. Artificial neural network (ANN), fuzzy logic (...This paper presents a comprehensive review of various traditional systems of crude oil distillation column design, modeling, simulation, optimization and control methods. Artificial neural network (ANN), fuzzy logic (FL) and genetic algorithm (GA) framework were chosen as the best methodologies for design, optimization and control of crude oil distillation column. It was discovered that many past researchers used rigorous simulations which led to convergence problems that were time consuming. The use of dynamic mathematical models was also challenging as these models were also time dependent. The proposed methodologies use back-propagation algorithm to replace the convergence problem using error minimal method.展开更多
基金Supported by:National Natural Science Foundation of China under Grant No.51208175the Fundamental Research Funds for the Central Universities under Grant Nos.2015B17514 and 2016B20514
文摘Four types of seismic design details were tested using 11 transfer column specimens and one comparison specimen of RC under low cyclic reversed loading. Test results show that diagonal cracks control the failure pattern and damage occurs mainly in the RC section with weak shear capacity in the transfer columns. There is a large difference in the bearing capacity and ductility of the transfer columns according to the test results, which indicates that the strengthening effect of diverse structural measures is quite different. The section ratio of I-section-encased steel and the axial compression ratio also have a great influence on the bearing capacity and ductility. Although the bearing capacity of transfer columns with additional longitudinal bars and additional X bars is relatively large, they have poor deformation capacity. Setting more stirrups along the columns is the best structural measure to enhance the seismic performance. The studs on the I-sectionencased steel by welding can help to complete the stress transfer between the steel and concrete, and avoid performance degradation of the two materials due to bonding failure.
基金Supported by the National Natural Science Foundation of China.
文摘Based on single drop mass transfer models and two phase flow equation,a general equationfor calculating the‘true’height of transfer unit of extraction columns was derived and tested withfour types of extraction columns with some different working systems.The calculated results fittedwell with those obtained by experiments.
基金Supported by the National Natural Science Foundation of China(20736005)
文摘The effect of different surfactants(n-octyltrimethylammonium bromide(OTABr),sodium dodecyl benzene sulfonate(SDBS) and Tween 80) with different critical micelle concentrations(CMC) on the CO_2 absorption into aqueous solutions in a bubble column is analyzed in the present work.The presence of these surfactants increased the gas-liquid interfacial area,and decreased the liquid phase mass transfer coefficient,but with significant different extent.The results indicated that the CMC can be a key parameter affecting the mass transfer of CO_2 absorption into a dilute aqueous solution of a surfactant.Sardeing's model was used to fit the experimental data successfully by re-correlating the parameters.
文摘The volumetric overall mass transfer coefficients in a multistage column have been measured using axial dispersion model for toluene–acetone–water system. The effect of operating parameters on the volumetric overall mass transfer coefficients has been investigated for both mass transfer directions. The results show that the mass transfer performance is strongly dependent on rotor speed and mass transfer direction, although only slightly dependent on phase flow rates. In addition, empirical correlations to predict the overall mass transfer coefficients have been developed. The proposed correlations based on dimensionless numbers can be considered as a useful tool for the possible scale up of the multistage column extractor.
基金supported by the National Natural Science Foundation of China(No.20575030)
文摘To make more homogenous organic monolithic structure, reversible addition-fragmentation chain transfer （RAFT） process was employed in the synthesis of the clenbuterol imprinted polymer. In the synthesis, the influence of synthetic conditions on the polymer structure and separation efficiency was studied. The result demonstrated that the imprinted columns prepared with RAFT process have higher column efficiency and selectivity than the columns prepared with conventional polymerization in the present study, which may result from the higher surface area, smaller pore size and the narrower globule size distribution in their structures. The result indicated that RAFT polymerization provided better conditions for the clenbuterol imprinted monolithic polymer preparation. 2009 Xiang Chao Dong. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.
基金supported by the Natural Science Research Youth Foundation of Hebei Higher Education of China [QN2016084]the National Natural Science Foundation of China[21878066]
文摘This paper investigates the thermal-coupled effect across the wall and the optimal heat transfer region of the wall for enhancing the energy saving effect of dividing wall column (DWC), and also studies the effects of feed thermal condition (q) and middle component composition of feed (cB) on the heat transfer process, the optimal heat transfer region, and the maximum heat transfer quantity across the wall. The simulation results show that the maximum heat transfer quantity across the wall and the potential for energy saving increase with the increase of q, while with the limitation of temperature difference across the wall, the beneficial heat transfer effect between certain range of stages, which are involved in the optimal heat transfer region, cannot be realized completely for a specific value of q. Besides, compared with q, a changing cB does not change the degree of realizing the beneficial heat transfer effect, but can bring about the variation of liquid split ratio (RL) and vapor split ratio (Rv). Thus, for achieving a maximum energy-saving effect of DWC, different q and cB need to find its own corresponding suitable heat transfer process across the wall.
文摘Heat transfer and bubble phenomena were investigated by adopting the drift flux model in a viscous slurry bubble column reactor (SBCR), having a diameter of 0.0508 m(ID) and height 1.5 m. The effects of superficial gas velocity (0.002 -0.164 m/s), solid concentration (0 - 20 wt%) and liquid viscosity (paraffin oil;16.9 mPa•s and squalane;25.9 mPa•s) on the gas holdup and heat transfer characteristics were examined. It was observed that the gas holdup increased with increasing superficial gas velocity (UG), but decreased with increasing solid concentration (SC) or slurry viscosity. The degree of non-uniformity in a SBCR could be determined by the modified drift flux model at the heterogeneous flow regime. The local heat transfer coefficient (h) between the immersed heater and the bed decreased with increasing liquid viscosity and SC, but it increased with increasing UG. The modified Nusselt number including the gas holdup and local heat transfer coefficient was well correlated in terms of dimensionless groups such as Reynolds and Prandtl numbers.
基金Supported by the National Natural Science Fundation of China.
文摘Hydrodynamics and mass transfer experiments were carried out in a 0.1m diameter extraction column with a new type (FG) stack packing developed recently in our laboratory.The working systems used were n-Butano1/Succinic acid/water with low interfacial tension of 1.50×10-3N·m-1 and 30% TBP (Kerosene)/Acetic acid/water with interfacial tension of 10.0×10-3N· m-1. Experimental results obtained indicated that (FG) stack packed extraction column was proved to possess high throughput capacity and excellent mass transfer efficiency. Replacing rotary discs with FG packings in a lube furfural extraction tower was quite success with significant economical benefits being claimed.
文摘The axial mixing is a key factor for design and scaling up of the pulsed extraction column which has strong influence on the mass transfer performances of the pulsed extraction column with discs and doughnuts. A steady-state concentration profile measurement was used to evaluate the mass transfer and axial mixing coefficients for the nitric acid/water/30%TRPO (in kerosene) system in the pulsed extraction column with the diameter of 38 mm on the condition of the TRPO-kerosene solution as the continuous phase and the flow ratio of 1∶1. Experimental results indicate that Ey evaluated by the experiments is in good agreement with that given by Burratti’s correlation; the axial mixing is far smaller for the continuous phase than that for the dispersed phase. However the empirical correlation for HOX is only given based on the present data.
文摘The variation in arc characteristics and behavior of metal transfer with the change in pulse parameters has been studied by high speed video camera during pulse current flux-cored arc weld deposition.A comparative study of similar nature has also been carried out during flux-cored arc weld deposition in globular and spray transfer modes.The effect of pulse parameters has been studied by considering their mean current and arc voltage.The arc characteristics studied by its root diameter,projected diameter and length,and the behavior of metal transfer noted by the metal transfer model and the droplet diameter have been found to vary significantly with the pulse parameters.The observation may help in understanding the arc characteristics with respect to the variation in pulse parameters which may be beneficial in using pulse current FCAW to produce desired weld quality.
基金Projects(50605023 50436010) supported by the National Natural Science Foundation of China
文摘Enhanced boiling experiments of two different enhanced structures were carried out in a thermosyphon loop evaporator chamber. One was micro-columns array structure (MCAS), which was fabricated on copper plate surface with interaction high speed wire electrode discharge machining (HS-WEDM). The other was the ramification of MCAS, named micro-column-array and sintered-copper compound structure (MSCS), which was fabricated with sintered method on micro-column array structure. Considering the wall superheat and critical heat flux (CHF), comparisons were made between them. The results show that both MCAS and MSCS can enhance the boiling heat transfer. It is also found that the enhanced boiling heat transfer ability of MSCS is changed obviously while the porosity of the sintered copper layer is changed.
文摘Correlations will be presented to describe liquid hold up, loading and flooding capacity, volumetric mass transfer coefficients on liquid and gas or vapour phase and the pressure drop as a basis for computing packed columns, dumped and regular as well, including the influence of end effects on scaling. The relationships are found on a sound physical and mathematical basis and their validity were confirmed by experimental investigations of many packings; some of them were selected to be considered in this work.
文摘This paper presents a comprehensive review of various traditional systems of crude oil distillation column design, modeling, simulation, optimization and control methods. Artificial neural network (ANN), fuzzy logic (FL) and genetic algorithm (GA) framework were chosen as the best methodologies for design, optimization and control of crude oil distillation column. It was discovered that many past researchers used rigorous simulations which led to convergence problems that were time consuming. The use of dynamic mathematical models was also challenging as these models were also time dependent. The proposed methodologies use back-propagation algorithm to replace the convergence problem using error minimal method.
