Titanium dioxide(Ti O_(2))nanopowder(P-25;Degussa AG)was treated using dielectric barrier discharge(DBD)in a rotary electrode DBD(RE-DBD)reactor.Its electrical and optical characteristics were investigated during RE-D...Titanium dioxide(Ti O_(2))nanopowder(P-25;Degussa AG)was treated using dielectric barrier discharge(DBD)in a rotary electrode DBD(RE-DBD)reactor.Its electrical and optical characteristics were investigated during RE-DBD generation.The treated TiO_(2)nanopowder properties and structures were analyzed using x-ray diffraction(XRD)and Fourier-transform infrared spectroscopy(FTIR).After RE-DBD treatment,XRD measurements indicated that the anatase peak theta positions shifted from 25.3°to 25.1°,which can be attributed to the substitution of new functional groups in the TiO_(2)lattice.The FTIR results show that hydroxyl groups(OH)at 3400 cm-1 increased considerably.The mechanism used to modify the TiO_(2)nanopowder surface by air DBD treatment was confirmed from optical emission spectrum measurements.Reactive species,such as OH radical,ozone and atomic oxygen can play key roles in hydroxyl formation on the TiO_(2)nanopowder surface.展开更多
The electrochemical behaviour of Ti(Ⅲ) and Ti(Ⅱ) in LiCl-KCl eutectic system has been studied by cyclic voltammetry and chronoamperometry.The cathodic reduction of Ti(Ⅲ) and Ti(Ⅱ) has been found to be stepwise:Ti(...The electrochemical behaviour of Ti(Ⅲ) and Ti(Ⅱ) in LiCl-KCl eutectic system has been studied by cyclic voltammetry and chronoamperometry.The cathodic reduction of Ti(Ⅲ) and Ti(Ⅱ) has been found to be stepwise:Ti(Ⅲ)+e=Ti(Ⅱ),Ti(Ⅱ)+2e =Ti.The reductions are diffusion controlled.When an equilibrium between Ti subchlorides and excess metallic Ti was estab- lished by reaction 2TiCl_3+Ti=3TiCl_2 in LiCl-KCl melt at 475℃,then the average valence of Ti is less than 2.1.In this system the diffusion coefficient for Ti(Ⅱ) ion was calculated as D=2.5×10^(-5)cm^2·s^(-1).The chronoamperometric studies showed that the initial nucleation stage and growth of nuclei were observed when Ti ions were electrodeposited on low carbon steel substrate. The investigation of nucleation of metal may provide the method for obtaining smooth,coherent and adherent deposits of titanium.展开更多
TiO2 thin films were prepared with Ti2O3, Ti3O5 and TiO2 as raw materials, by electron-beam evaporation deposition, using O^2- ion beam （ O2 purity up to 99.99% ） as auxiliary means. The crystal structures of the sa...TiO2 thin films were prepared with Ti2O3, Ti3O5 and TiO2 as raw materials, by electron-beam evaporation deposition, using O^2- ion beam （ O2 purity up to 99.99% ） as auxiliary means. The crystal structures of the samples were inspected by the X-ray diffraction （XRD） method, and the evaporation character of warious raw materials was analyzed. Transmittance spectra were measured through a U-3310 spectrophotometer （ wavelength ranging from 200 nm to 900 nm）. The refractive index n and the thickness of films were determined from transmission spectra. The experimental results show that the thin films taking Ti2O3 as their raw material have a strong absorption, when taking Ti3O5 and TiO2 as raw materials, the thin films would have good optical properties. The experiments also show that, the crystal structure of all thin films is amorphous before post-annealing and the Ti3O5 is a congruent evaporation phase in the Ti-O system.展开更多
In order to improve the lifespan of spot-welding electrodes used for welding zinc coated steel sheets, titanium diboride was deposited onto their surface after precoating nickel as an intermediate layer. The microstru...In order to improve the lifespan of spot-welding electrodes used for welding zinc coated steel sheets, titanium diboride was deposited onto their surface after precoating nickel as an intermediate layer. The microstructures and phase compositions of TiB2 and Ni coatings were characterized by SEM and XRD. The coating hardness was measured using a microhardness tester. The results indicate that a satisfactory TiB2 coating is obtained as a result of the intermediate nickel layer acting as a good binder between the TiB2 coating and the copper alloy substrate. Owing to its capacity of deforming, the precoated nickel layer is dense and crack free, while cracks and pores are observed in the TiB2 coating. The hardness of the TiB2/Ni coating decreases with the increase of voltage and capacitance because of the diffusion of copper and nickel and the oxidation of the coating materials. Because of the good thermal and electrical conductivities and high hardness properties of TiB2, the deformation of the electrode with TiB2/Ni coating is reduced and its spot-welding life is by far prolonged than that of the uncoated one.展开更多
The effect of metal （Ti, Ni, and Au） electrodes on humidity sensing properties of electrospun TiO2 nanofibers was investigated in this work. The devices were fabricated by evaporating metal contacts on SiO2 layer th...The effect of metal （Ti, Ni, and Au） electrodes on humidity sensing properties of electrospun TiO2 nanofibers was investigated in this work. The devices were fabricated by evaporating metal contacts on SiO2 layer thermally grown on silicon substrate. The separation between the electrodes was 90 μm for all sensors. The sensors were tested from 40% to 90% relative humidity （RH） by AC electrical characterization at room temperature. When sensors are switched between 40% and 90% RH, the corresponding response and recovery time are 3 s and 5 s for Ti-electrode sensor, 4 s and 7 s for Ni-electrode sensor, and 7 s and 13 s for Au-electrode sensor. The hysteresis was 3%, 5% and 15% for sensitivity of Ti, Ni, and Au-electrode sensors are Ti-, Ni-, and Au-electrode sensor, respectively. The 7.53 MΩ/%RH, 5.29 MΩ/%RH and 4.01 MΩ/%RH respectively at 100 Hz. Therefore Ti-electrode sensor is found to have linear response, fast response and recovery time and higher sensitivity as compared with those of Ni- and Au-electrode sensors. Comparison of humidity sensing properties of sensors with different electrode material may propose a compelling route for designing and optimizing humidity sensors.展开更多
Unveiling the active site of an electrocatalyst is fundamental for the development of efficient electrode material.For the two-electron water oxidation to produce H_(2)O_(2),competitive reactions,including four-and on...Unveiling the active site of an electrocatalyst is fundamental for the development of efficient electrode material.For the two-electron water oxidation to produce H_(2)O_(2),competitive reactions,including four-and one-electron water oxidation and surface reconstruction derived from the high-oxidative environment co-existed,leading to great challenges to identify the real active sites on the electrode.In this work,Ti/TiO_(2)-based electrodes calcined under air,nitrogen,or urea atmospheres were selected as electrocatalysts for two-electron water oxidation.Electrochemical analyses were applied to evaluate the catalytic activity and selectivity.The morphological and current change on the electrode surface were determined by scanning electrochemical microscopy,while the chemical and valence evolutions with depth distributions were tested by XPS combined with cluster argon ion sputtering.The results demonstrated that Ti/TiO_(2) nanotube arrays served as the support,while the functional groups of carbonyl groups and pyrrolic nitrogen derived from the co-pyrolysis with urea were the active sites for the H_(2)O_(2) production.This finding provided a new horizon to design efficient catalysts for H_(2)O_(2) production.展开更多
为了优选TiO_(2)电极最适宜尺寸,提高栽培基质pH值在线检测的综合性能,利用磁控溅射法将TiO_(2)薄膜沉积在氧化铟锡/玻璃(Indium Tin Oxide/Glass,ITO/Glass)基板上,制备不同膜厚和面积的pH敏感电极,搭配固态Ag/AgCl参比电极构建pH传感...为了优选TiO_(2)电极最适宜尺寸,提高栽培基质pH值在线检测的综合性能,利用磁控溅射法将TiO_(2)薄膜沉积在氧化铟锡/玻璃(Indium Tin Oxide/Glass,ITO/Glass)基板上,制备不同膜厚和面积的pH敏感电极,搭配固态Ag/AgCl参比电极构建pH传感器.利用扫描电子显微镜(SEM)观察电极薄膜表面形貌发展规律,分析响应特性;在标准pH缓冲溶液中测试传感器响应特性.结果表明:较厚的TiO_(2)敏感膜具有更好的疏松多孔结构,传感器响应稳定性优异,但是响应灵敏度差;综合优选膜厚度为200 nm、膜尺寸为15 mm×15 mm的TiO_(2)敏感电极,pH值响应综合性能接近玻璃电极传感器;利用优选传感器在栽培基质pH检测应用试验中,pH检测最大绝对误差为0.52单位;通过对误差规律的总结,构建质量含水率补偿模型;经过质量含水率补偿后,pH检测最大绝对误差降低到了0.12单位,相对误差在5%以下,满足栽培基质pH值在线检测性能要求.展开更多
文摘Titanium dioxide(Ti O_(2))nanopowder(P-25;Degussa AG)was treated using dielectric barrier discharge(DBD)in a rotary electrode DBD(RE-DBD)reactor.Its electrical and optical characteristics were investigated during RE-DBD generation.The treated TiO_(2)nanopowder properties and structures were analyzed using x-ray diffraction(XRD)and Fourier-transform infrared spectroscopy(FTIR).After RE-DBD treatment,XRD measurements indicated that the anatase peak theta positions shifted from 25.3°to 25.1°,which can be attributed to the substitution of new functional groups in the TiO_(2)lattice.The FTIR results show that hydroxyl groups(OH)at 3400 cm-1 increased considerably.The mechanism used to modify the TiO_(2)nanopowder surface by air DBD treatment was confirmed from optical emission spectrum measurements.Reactive species,such as OH radical,ozone and atomic oxygen can play key roles in hydroxyl formation on the TiO_(2)nanopowder surface.
文摘The electrochemical behaviour of Ti(Ⅲ) and Ti(Ⅱ) in LiCl-KCl eutectic system has been studied by cyclic voltammetry and chronoamperometry.The cathodic reduction of Ti(Ⅲ) and Ti(Ⅱ) has been found to be stepwise:Ti(Ⅲ)+e=Ti(Ⅱ),Ti(Ⅱ)+2e =Ti.The reductions are diffusion controlled.When an equilibrium between Ti subchlorides and excess metallic Ti was estab- lished by reaction 2TiCl_3+Ti=3TiCl_2 in LiCl-KCl melt at 475℃,then the average valence of Ti is less than 2.1.In this system the diffusion coefficient for Ti(Ⅱ) ion was calculated as D=2.5×10^(-5)cm^2·s^(-1).The chronoamperometric studies showed that the initial nucleation stage and growth of nuclei were observed when Ti ions were electrodeposited on low carbon steel substrate. The investigation of nucleation of metal may provide the method for obtaining smooth,coherent and adherent deposits of titanium.
文摘TiO2 thin films were prepared with Ti2O3, Ti3O5 and TiO2 as raw materials, by electron-beam evaporation deposition, using O^2- ion beam （ O2 purity up to 99.99% ） as auxiliary means. The crystal structures of the samples were inspected by the X-ray diffraction （XRD） method, and the evaporation character of warious raw materials was analyzed. Transmittance spectra were measured through a U-3310 spectrophotometer （ wavelength ranging from 200 nm to 900 nm）. The refractive index n and the thickness of films were determined from transmission spectra. The experimental results show that the thin films taking Ti2O3 as their raw material have a strong absorption, when taking Ti3O5 and TiO2 as raw materials, the thin films would have good optical properties. The experiments also show that, the crystal structure of all thin films is amorphous before post-annealing and the Ti3O5 is a congruent evaporation phase in the Ti-O system.
基金Project (50575069) supported by the National Natural Science Foundation of China
文摘In order to improve the lifespan of spot-welding electrodes used for welding zinc coated steel sheets, titanium diboride was deposited onto their surface after precoating nickel as an intermediate layer. The microstructures and phase compositions of TiB2 and Ni coatings were characterized by SEM and XRD. The coating hardness was measured using a microhardness tester. The results indicate that a satisfactory TiB2 coating is obtained as a result of the intermediate nickel layer acting as a good binder between the TiB2 coating and the copper alloy substrate. Owing to its capacity of deforming, the precoated nickel layer is dense and crack free, while cracks and pores are observed in the TiB2 coating. The hardness of the TiB2/Ni coating decreases with the increase of voltage and capacitance because of the diffusion of copper and nickel and the oxidation of the coating materials. Because of the good thermal and electrical conductivities and high hardness properties of TiB2, the deformation of the electrode with TiB2/Ni coating is reduced and its spot-welding life is by far prolonged than that of the uncoated one.
基金support of the Higher Education Commission(HEC),Pakistan
文摘The effect of metal （Ti, Ni, and Au） electrodes on humidity sensing properties of electrospun TiO2 nanofibers was investigated in this work. The devices were fabricated by evaporating metal contacts on SiO2 layer thermally grown on silicon substrate. The separation between the electrodes was 90 μm for all sensors. The sensors were tested from 40% to 90% relative humidity （RH） by AC electrical characterization at room temperature. When sensors are switched between 40% and 90% RH, the corresponding response and recovery time are 3 s and 5 s for Ti-electrode sensor, 4 s and 7 s for Ni-electrode sensor, and 7 s and 13 s for Au-electrode sensor. The hysteresis was 3%, 5% and 15% for sensitivity of Ti, Ni, and Au-electrode sensors are Ti-, Ni-, and Au-electrode sensor, respectively. The 7.53 MΩ/%RH, 5.29 MΩ/%RH and 4.01 MΩ/%RH respectively at 100 Hz. Therefore Ti-electrode sensor is found to have linear response, fast response and recovery time and higher sensitivity as compared with those of Ni- and Au-electrode sensors. Comparison of humidity sensing properties of sensors with different electrode material may propose a compelling route for designing and optimizing humidity sensors.
基金Project(2021JJ30792) supported by the Natural Science Foundation of Hunan Province,ChinaProject(52170031) supported by the National Natural Science Foundation of ChinaProject supported by the Fundamental Research Funds for the Central Universities,China。
文摘Unveiling the active site of an electrocatalyst is fundamental for the development of efficient electrode material.For the two-electron water oxidation to produce H_(2)O_(2),competitive reactions,including four-and one-electron water oxidation and surface reconstruction derived from the high-oxidative environment co-existed,leading to great challenges to identify the real active sites on the electrode.In this work,Ti/TiO_(2)-based electrodes calcined under air,nitrogen,or urea atmospheres were selected as electrocatalysts for two-electron water oxidation.Electrochemical analyses were applied to evaluate the catalytic activity and selectivity.The morphological and current change on the electrode surface were determined by scanning electrochemical microscopy,while the chemical and valence evolutions with depth distributions were tested by XPS combined with cluster argon ion sputtering.The results demonstrated that Ti/TiO_(2) nanotube arrays served as the support,while the functional groups of carbonyl groups and pyrrolic nitrogen derived from the co-pyrolysis with urea were the active sites for the H_(2)O_(2) production.This finding provided a new horizon to design efficient catalysts for H_(2)O_(2) production.
