The effect of holding time of double annealing process on the microstructure and mechanical properties of Ti-5Al-5Mo-5V1Cr-1Fe(Ti55511)alloy was investigated.Results reveal that the shape and size of the primaryα(α_...The effect of holding time of double annealing process on the microstructure and mechanical properties of Ti-5Al-5Mo-5V1Cr-1Fe(Ti55511)alloy was investigated.Results reveal that the shape and size of the primaryα(α_(p))phase are predominantly influenced by the holding time at the first stage.With the prolongation of holding time,the long strip of α_(p) is transformed into a short rod due to the terminal migration mechanism,leading to the broadening growth,and the growth of α_(p) slows down when the holding time is over 2 h.The volume fraction of α_(p) is mainly affected by the holding time of the second stage:with the prolongation of holding time,the volume fraction of α_(p) is increased,which is accompanied by the precipitation of the secondaryα(α_(s)).The mechanical properties of Ti55511 alloy are influenced by bothα_(p) andαs.Tensile results indicate that the optimal holding time of double annealing is 1-4 h for the first stage and 0.5-2 h for the second stage.展开更多
Port structures constitute the main link in the maritime transport chain of coastal countries and therefore contribute to their economic development. But it should be noted that the installation of said works is not w...Port structures constitute the main link in the maritime transport chain of coastal countries and therefore contribute to their economic development. But it should be noted that the installation of said works is not without consequences for the countries concerned. Benin, a country in the Gulf of Guinea, is no exception to this phenomenon because, due to its maritime history, it has a heritage of port structures. These structures, built on its coastline, cause a wide variety of environmental problems such as silting and erosion on either side of them. The general objective of this article is to contribute to the proper functionality of port facilities while minimizing environmental problems that may arise. It aims to provide managers with a tool allowing them to fully understand the state of their assets in order to rationalize maintenance actions. In order to achieve this objective, an assessment of the state of the structure, and then a structural diagnosis are necessary and recommendations can be established to restore the level of service of the latter. As a result, two examples were presented: the wharf of the Sèmè-Podji pipeline project and the maritime piles project of the Wasco de Gama bridge (control project), and recommendations adapted to this objective were established. The comparative analysis of the two examples, both maritime works, revealed an under-sizing at the level of the spans of the wharf bridge of the Sèmè-Podji pipeline project (spans of 7 m in length), while these spans vary on average by 45 m to 62 m for the Wasco da Gama bridge. Bringing the piles closer together at the Sèmè-Podji wharf reduces the energy of the current which promotes the accumulation of sediment. The structure no longer experiences a flow capable of setting in motion the sands accumulated since at least 2022. This element appears to be a fundamental characteristic explaining the erosion observed to the east of the structure.展开更多
The damage distribution of the same type of aircraft in similar service environments should be similar. Based on this assumption, to perform the maintenance and repair of aircraft composite structures, the damage of c...The damage distribution of the same type of aircraft in similar service environments should be similar. Based on this assumption, to perform the maintenance and repair of aircraft composite structures, the damage of composite structures in a certain type of aircraft were investigated. The time-varying damage distribution model was established and verified based on the damage of a 16-aircraft fleet. The results show that the quantitative proportions of structural damage are 74% for skin delamination, 22% for stringer delamination and 3% for stringer-skin interface debonding. The amount of structural damages increases linearly with service time while the proportion of different damages does not change. As the service time increases, the geometric parameter distribution of damage for the same type of aircraft gradually converges, which can be approximated using the same function. There are certain differences in the proportion and geometric parameter distribution of damages among different components and locations, and the differences do not change over time.展开更多
It is crucial to predict future mechanical behaviors for the prevention of structural disasters.Especially for underground construction,the structural mechanical behaviors are affected by multiple internal and externa...It is crucial to predict future mechanical behaviors for the prevention of structural disasters.Especially for underground construction,the structural mechanical behaviors are affected by multiple internal and external factors due to the complex conditions.Given that the existing models fail to take into account all the factors and accurate prediction of the multiple time series simultaneously is difficult using these models,this study proposed an improved prediction model through the autoencoder fused long-and short-term time-series network driven by the mass number of monitoring data.Then,the proposed model was formalized on multiple time series of strain monitoring data.Also,the discussion analysis with a classical baseline and an ablation experiment was conducted to verify the effectiveness of the prediction model.As the results indicate,the proposed model shows obvious superiority in predicting the future mechanical behaviors of structures.As a case study,the presented model was applied to the Nanjing Dinghuaimen tunnel to predict the stain variation on a different time scale in the future.展开更多
The grain size of TiAl alloy castings prepared by traditional casting process is coarse,thus showing poor mechanical properties.In this study,a new type of high performance Ti-46Al alloy tube prepared by vacuum centri...The grain size of TiAl alloy castings prepared by traditional casting process is coarse,thus showing poor mechanical properties.In this study,a new type of high performance Ti-46Al alloy tube prepared by vacuum centrifugal casting technology was introduced.This research comprehensively examined the influence of pouring time on the microstructure and mechanical performance of the castings,employing both experimental approaches and ProCast simulation methodologies.The findings indicate that prolonging the pouring time facilitates a microstructural evolution from coarse columnar grains to refined equiaxed grains.Under the condition of pouring temperature of 1,600℃,rotation speed of 800 r·min^(-1) and pouring time of 6 s,the tensile strength of Ti-46Al alloy at room temperature reaches 650 MPa,and the tensile strength at 800℃ reaches 705 MPa,which is significantly higher than that of traditional as-cast Ti-Al alloy.展开更多
Tilted metasurface nanostructures,with excellent physical properties and enormous application potential,pose an urgent need for manufacturing methods.Here,electric-field-driven generative-nanoimprinting technique is p...Tilted metasurface nanostructures,with excellent physical properties and enormous application potential,pose an urgent need for manufacturing methods.Here,electric-field-driven generative-nanoimprinting technique is proposed.The electric field applied between the template and the substrate drives the contact,tilting,filling,and holding processes.By accurately controlling the introduced included angle between the flexible template and the substrate,tilted nanostructures with a controllable angle are imprinted onto the substrate,although they are vertical on the template.By flexibly adjusting the electric field intensity and the included angle,large-area uniform-tilted,gradient-tilted,and high-angle-tilted nanostructures are fabricated.In contrast to traditional replication,the morphology of the nanoimprinting structure is extended to customized control.This work provides a cost-effective,efficient,and versatile technology for the fabrication of various large-area tilted metasurface structures.As an illustration,a tilted nanograting with a high coupling efficiency is fabricated and integrated into augmented reality displays,demonstrating superior imaging quality.展开更多
Vacancy defects,as fundamental disruptions in metallic lattices,play an important role in shaping the mechanical and electronic properties of aluminum crystals.However,the influence of vacancy position under coupled t...Vacancy defects,as fundamental disruptions in metallic lattices,play an important role in shaping the mechanical and electronic properties of aluminum crystals.However,the influence of vacancy position under coupled thermomechanical fields remains insufficiently understood.In this study,transmission and scanning electron microscopy were employed to observe dislocation structures and grain boundary heterogeneities in processed aluminum alloys,suggesting stress concentrations and microstructural inhomogeneities associated with vacancy accumulation.To complement these observations,first-principles calculations and molecular dynamics simulations were conducted for seven single-vacancy configurations in face-centered cubic aluminum.The stress response,total energy,density of states(DOS),and differential charge density were examined under varying compressive strain(ε=0–0.1)and temperature(0–600 K).The results indicate that face-centered vacancies tend to reduce mechanical strength and perturb electronic states near the Fermi level,whereas corner and edge vacancies appear to have weaker effects.Elevated temperatures may partially restore electronic uniformity through thermal excitation.Overall,these findings suggest that vacancy position exerts a critical but position-dependent influence on coupled structure-property relationships,offering theoretical insights and preliminary experimental support for defect-engineered aluminum alloy design.展开更多
Covert timing channels(CTC)exploit network resources to establish hidden communication pathways,posing signi cant risks to data security and policy compliance.erefore,detecting such hidden and dangerous threats remain...Covert timing channels(CTC)exploit network resources to establish hidden communication pathways,posing signi cant risks to data security and policy compliance.erefore,detecting such hidden and dangerous threats remains one of the security challenges. is paper proposes LinguTimeX,a new framework that combines natural language processing with arti cial intelligence,along with explainable Arti cial Intelligence(AI)not only to detect CTC but also to provide insights into the decision process.LinguTimeX performs multidimensional feature extraction by fusing linguistic attributes with temporal network patterns to identify covert channels precisely.LinguTimeX demonstrates strong e ectiveness in detecting CTC across multiple languages;namely English,Arabic,and Chinese.Speci cally,the LSTM and RNN models achieved F1 scores of 90%on the English dataset,89%on the Arabic dataset,and 88%on the Chinese dataset,showcasing their superior performance and ability to generalize across multiple languages. is highlights their robustness in detecting CTCs within security systems,regardless of the language or cultural context of the data.In contrast,the DeepForest model produced F1-scores ranging from 86%to 87%across the same datasets,further con rming its e ectiveness in CTC detection.Although other algorithms also showed reasonable accuracy,the LSTM and RNN models consistently outperformed them in multilingual settings,suggesting that deep learning models might be better suited for this particular problem.展开更多
We study age-structured branching models with reproduction law depending on the remaining lifetime of the parent. The lifespan of an individual is determined at its birth and its remaining lifetime decreases at the un...We study age-structured branching models with reproduction law depending on the remaining lifetime of the parent. The lifespan of an individual is determined at its birth and its remaining lifetime decreases at the unit speed. The models, without or with immigration, are constructed as measure-valued processes by pathwise unique solutions of stochastic equations driven by time-space Poisson random measures. In the subcritical branching case, we give a sufficient condition for the ergodicity of the process with immigration. Two large number laws and a central limit theorem of the occupation times are proved.展开更多
According to the failure characteristics of aircraft structure, a delay-time model is an effective method to optimize maintenance for aircraft structure. To imitate the practical situation as much as possible, imperfe...According to the failure characteristics of aircraft structure, a delay-time model is an effective method to optimize maintenance for aircraft structure. To imitate the practical situation as much as possible, imperfect inspections, thresholds and repeated intervals are concerned in delay-time models. Since the suggestion by the existing delay-time models that the inspections are implemented in an infinite time span lacks practical value, a de- lay-time model with imperfect inspection within a finite time span is proposed. In the model, the nonhomogenous Poisson process is adopted to obtain the renewal probabilities between two different successive inspections on de- fects or failures. An algorithm is applied based on the Nelder-Mead downhill simplex method to solve the model. Finally, a numerical example proves the validity and effectiveness of the model.展开更多
A new β-Ti based Ti35Nb2.5Sn/10 hydroxyapitite（HA） biocompatible composite was fabricated by mechanical milling and pulsed current activated sintering（PCAS）.The microstructures of Ti35Nb2.5Sn/10HA powder particle...A new β-Ti based Ti35Nb2.5Sn/10 hydroxyapitite（HA） biocompatible composite was fabricated by mechanical milling and pulsed current activated sintering（PCAS）.The microstructures of Ti35Nb2.5Sn/10HA powder particles and composites sintered from the milled powders were studied.Results indicated that α-Ti phase began to transform into β-Ti phase after the powders were mechanically milled for 8 h.After mechanical milling for 12 h,α-Ti completely transformed into β-Ti phase,and the ultra fine Ti35Nb2.5Sn/10HA composite powders were obtained.And ultra fine grain sized Ti35Nb2.5Sn/10HA sintered composites were obtained by PCAS.The hardness and relative density of the sintered composites both increased with increasing the ball milling time.展开更多
In this paper, a new method of time reversal for defect diagnosis of concealed structure has been proposed based on the detecting technique of structure acoustic wave and the theory of time reversal. The time reversal...In this paper, a new method of time reversal for defect diagnosis of concealed structure has been proposed based on the detecting technique of structure acoustic wave and the theory of time reversal. The time reversal recurrence formula for detecting the acoustic wave speed constitution of concealed structures with bilevel asynchronous test has been established. The wave speed constitution can be reconstructed in 2 D graticule form by means of this method. The result of model test shows the method is valid.展开更多
In this paper, a predator -prey model with stage structure and double time delays in pollution environment is modeled. By using comparison theorem of impulsive differential equation, dynamics behaviors of the system i...In this paper, a predator -prey model with stage structure and double time delays in pollution environment is modeled. By using comparison theorem of impulsive differential equation, dynamics behaviors of the system is analysised. We prove that the pest-extinction solution of the system is the globally attractive for R 1 <1.展开更多
In the procedure of coal industry production, the losses of the persons and economy caused by the gas explosion accidents are most serious, therefore, prevention and control of the gas explosion accident of the coal m...In the procedure of coal industry production, the losses of the persons and economy caused by the gas explosion accidents are most serious, therefore, prevention and control of the gas explosion accident of the coal mines is an important issue needed to be solved urgently in the safety production work of our coal mines. The characteristic of time structure variation index characteristic was analyzed about gas concentration sequence of three measure points in the NO. 1I 1024 working face. It was found that the value of time variation about three measure points was mostly 1〈δ≤1.5, and gas emission presented consistently strong-clustering state twice, and the value of time variation presented continuous variation state in the active stage of gas concentration. Complex characteristics of the value indicated gas emission was continuously variable in time or space and presented the complex nonlinear characteristics. So the characteristic about gas emission system was correctly depicted and analyzed to gas emission system according to the relation of its state variation and essential of nonlinear system. The result also provided reliable warranty for its continued nonlinear research on gas emission.展开更多
A time domain finite element method （FEM） for the analysis of transient elastic response of a very large floating structure （VLFS） subjected to arbitrary time-dependent external loads is presented. This method is ...A time domain finite element method （FEM） for the analysis of transient elastic response of a very large floating structure （VLFS） subjected to arbitrary time-dependent external loads is presented. This method is developed directly in time domain and the hydrodynamic problem is formulated based on linear, inviscid and slightly compressible fluid theory and the structural response is analyzed on the thin plate assumption. The time domain finite element procedure herein is validated by comparing numerical results with available experimental data. Finally, the transient elastic response of a pontoon-type VLFS under the landing of an airplane is computed by the proposed time domain FEM. The time histories of the applied force and the position and velocity of an airplane during landing are modeled with data from a Boeing 747-400 jumbo jet.展开更多
In 1997 - 2003, 27 earthquakes with M≥ 5.0 occurred in the Jiashi-Bachu area of Xinjiang. It was a rare strong earthquake swarm activity. The earthquake swarm has three time segments of activity with different magnit...In 1997 - 2003, 27 earthquakes with M≥ 5.0 occurred in the Jiashi-Bachu area of Xinjiang. It was a rare strong earthquake swarm activity. The earthquake swarm has three time segments of activity with different magnitudes in the years 1997, 1998 and 2003. In different time segments, the seismic activity showed strengthenin-qguiet changes in various degrees before earthquakes with M ≥ 5.0. In order to delimitate effectively the precursory meaning of the clustering （strengthening） quiet change in sequence and to seek the time criterion for impending prediction, the nonlinear characteristics of seismic activity have been used to analyze the time structure characteristics of the earthquake swarm sequence, and further to forecast the development tendency of earthquake sequences in the future. Using the sequence catalogue recorded by the Kashi Station, and taking the earthquakes with Ms≥ 5.0 in the sequence as the starting point and the next earthquake with Ms = 5.0 as the end, statistical analysis has been performed on the time structure relations of the earthquake sequence in different stages. The main results are as follows： （1） Before the major earthquakes with M ≥ 5.0 in the swarm sequence, the time variation coefficient （δ-value） has abnormal demonstrations to different degrees. （2） Within 10 days after δ= 1, occurrence of earthquakes with M ≥ 5.0 in the swarm is very possible. （3） The time variation coefficient has three types of change. （4） The change process before earthquakes with M5.0 is similar to that before earthquakes with M6.0, with little difference in the threshold value. In the earthquake swarm sequence, it is difficult to delimitate accurately the attribute of the current sequences （foreshock or aftershock sequence） and to judge the magnitude of the follow-up earthquake by δ-value. We can only make the judgment that earthquakes with M5.0 are likely to occur in the sequence. （5） The critical clustering characteristics of the sequence are hierarchical. Only corresponding to a certain magnitude can the sequence have the variation state of critical clustering. （6） The coefficient of the time variation has a clear meaning in physics. After the clustering-quiet state of earthquake activity has appeared, it can describe clearly the randomness of the seismogenic system. Furthermore, it can efficiently clarify whether or not the clustering quiescence variation is of some prognostic meaning. In the case that the earthquake frequency attenuation is essentially normal （h 〉 1 ） and there is no remarkable clustering-quiescence state, it is still possible to discover the abnormal change of the sequence from the time variation coefficient. On the contrary, in the later period of swarm activity, after the appearance of many seismic quiescence phenomena, this coefficient did not appear abnormally, even when h 〈 1, suggesting that the δ-value diagnosis is more universal.展开更多
The 0.6 mol% CuO-doping 0.996(0.95 Na_(0.5)K_(0.5)NbO_3-0.05 LiSbO_3)-0.004 FeBiO_3(KNN-LSBF-CuO) piezoelectric ceramics were synthesized by a solid-state reaction technique, and the structure and piezoelectric proper...The 0.6 mol% CuO-doping 0.996(0.95 Na_(0.5)K_(0.5)NbO_3-0.05 LiSbO_3)-0.004 FeBiO_3(KNN-LSBF-CuO) piezoelectric ceramics were synthesized by a solid-state reaction technique, and the structure and piezoelectric properties dependence of sintering time in KNN-LS-BF-CuO ceramics were studied. It is found that all the samples sintered for various time are perovskite structure mixed with orthorhombic symmetry phase and tetragonal phase, but the sintering time has significant influences on the crystalline and properties. When the sintering time increases from 2 hours to 6 hours, the grain of KNN-LS-BF-CuO ceramics becomes more homogeneous and more tight-arrangement. The experimental results reveal that the longer sintering time than 4 hours is beneficial for improving partial properties, such as d_(33), tgδ, and Q_m, but is adverse to ε_r and k_p, the KNNLS-BF-CuO ceramics with optimum properties can be synthesized for 6 hours at 1 060 ℃.展开更多
In this study,the effect of decarburization annealing temperature and time on the carbon content,microstructure,and texture of grain-oriented pure iron was investigated by optical microscopy and scanning electron micr...In this study,the effect of decarburization annealing temperature and time on the carbon content,microstructure,and texture of grain-oriented pure iron was investigated by optical microscopy and scanning electron microscopy with electron-backscatter diffraction. The results showed that the efficiency of decarburization dramatically increased with increasing decarburization temperature. However,when the annealing temperature was increased to 825°C and 850°C,the steel's carbon content remained essentially unchanged at 0.002%. With increasing decarburization time,the steel's carbon content generally decreased. When both the decarburization temperature and time were increased further,the average grain size dramatically increased and the number of fine grains decreased; meanwhile,some relatively larger grains developed. The main texture types of the decarburized sheets were approximately the same: {001}<110> and {112~115}<110>,with a γ-fiber texture. Furthermore,little change was observed in the texture. Compared with the experimental sheets,the texture of the cold-rolled sheet was very scattered. The best average magnetic induction(B_(800)) among the final products was 1.946 T.展开更多
Kernel independent component analysis(KICA) is a newly emerging nonlinear process monitoring method,which can extract mutually independent latent variables called independent components(ICs) from process variables. Ho...Kernel independent component analysis(KICA) is a newly emerging nonlinear process monitoring method,which can extract mutually independent latent variables called independent components(ICs) from process variables. However, when more than one IC have Gaussian distribution, it cannot extract the IC feature effectively and thus its monitoring performance will be degraded drastically. To solve such a problem, a kernel time structure independent component analysis(KTSICA) method is proposed for monitoring nonlinear process in this paper. The original process data are mapped into a feature space nonlinearly and then the whitened data are calculated in the feature space by the kernel trick. Subsequently, a time structure independent component analysis algorithm, which has no requirement for the distribution of ICs, is proposed to extract the IC feature.Finally, two monitoring statistics are built to detect process faults. When some fault is detected, a nonlinear fault identification method is developed to identify fault variables based on sensitivity analysis. The proposed monitoring method is applied in the Tennessee Eastman benchmark process. Applications demonstrate the superiority of KTSICA over KICA.展开更多
Two approximation laws of sliding mode for discrete-time variable structure control systems are proposed to overcome the limitations of the exponential approximation law and the variable rate approximation law. By app...Two approximation laws of sliding mode for discrete-time variable structure control systems are proposed to overcome the limitations of the exponential approximation law and the variable rate approximation law. By applying the proposed approximation laws of sliding mode to discrete-time variable structure control systems, the stability of origin can be guaranteed, and the chattering along the switching surface caused by discrete-time variable structure control can be restrained effectively. In designing of approximation laws, the problem that the system control input is restricted is also considered, which is very important in practical systems. Finally a simulation example shows the effectiveness of the two approximation laws proposed.展开更多
文摘The effect of holding time of double annealing process on the microstructure and mechanical properties of Ti-5Al-5Mo-5V1Cr-1Fe(Ti55511)alloy was investigated.Results reveal that the shape and size of the primaryα(α_(p))phase are predominantly influenced by the holding time at the first stage.With the prolongation of holding time,the long strip of α_(p) is transformed into a short rod due to the terminal migration mechanism,leading to the broadening growth,and the growth of α_(p) slows down when the holding time is over 2 h.The volume fraction of α_(p) is mainly affected by the holding time of the second stage:with the prolongation of holding time,the volume fraction of α_(p) is increased,which is accompanied by the precipitation of the secondaryα(α_(s)).The mechanical properties of Ti55511 alloy are influenced by bothα_(p) andαs.Tensile results indicate that the optimal holding time of double annealing is 1-4 h for the first stage and 0.5-2 h for the second stage.
文摘Port structures constitute the main link in the maritime transport chain of coastal countries and therefore contribute to their economic development. But it should be noted that the installation of said works is not without consequences for the countries concerned. Benin, a country in the Gulf of Guinea, is no exception to this phenomenon because, due to its maritime history, it has a heritage of port structures. These structures, built on its coastline, cause a wide variety of environmental problems such as silting and erosion on either side of them. The general objective of this article is to contribute to the proper functionality of port facilities while minimizing environmental problems that may arise. It aims to provide managers with a tool allowing them to fully understand the state of their assets in order to rationalize maintenance actions. In order to achieve this objective, an assessment of the state of the structure, and then a structural diagnosis are necessary and recommendations can be established to restore the level of service of the latter. As a result, two examples were presented: the wharf of the Sèmè-Podji pipeline project and the maritime piles project of the Wasco de Gama bridge (control project), and recommendations adapted to this objective were established. The comparative analysis of the two examples, both maritime works, revealed an under-sizing at the level of the spans of the wharf bridge of the Sèmè-Podji pipeline project (spans of 7 m in length), while these spans vary on average by 45 m to 62 m for the Wasco da Gama bridge. Bringing the piles closer together at the Sèmè-Podji wharf reduces the energy of the current which promotes the accumulation of sediment. The structure no longer experiences a flow capable of setting in motion the sands accumulated since at least 2022. This element appears to be a fundamental characteristic explaining the erosion observed to the east of the structure.
文摘The damage distribution of the same type of aircraft in similar service environments should be similar. Based on this assumption, to perform the maintenance and repair of aircraft composite structures, the damage of composite structures in a certain type of aircraft were investigated. The time-varying damage distribution model was established and verified based on the damage of a 16-aircraft fleet. The results show that the quantitative proportions of structural damage are 74% for skin delamination, 22% for stringer delamination and 3% for stringer-skin interface debonding. The amount of structural damages increases linearly with service time while the proportion of different damages does not change. As the service time increases, the geometric parameter distribution of damage for the same type of aircraft gradually converges, which can be approximated using the same function. There are certain differences in the proportion and geometric parameter distribution of damages among different components and locations, and the differences do not change over time.
基金National Key Research and Development Program of China,Grant/Award Number:2018YFB2101003National Natural Science Foundation of China,Grant/Award Numbers:51991395,U1806226,51778033,51822802,71901011,U1811463,51991391Science and Technology Major Project of Beijing,Grant/Award Number:Z191100002519012。
文摘It is crucial to predict future mechanical behaviors for the prevention of structural disasters.Especially for underground construction,the structural mechanical behaviors are affected by multiple internal and external factors due to the complex conditions.Given that the existing models fail to take into account all the factors and accurate prediction of the multiple time series simultaneously is difficult using these models,this study proposed an improved prediction model through the autoencoder fused long-and short-term time-series network driven by the mass number of monitoring data.Then,the proposed model was formalized on multiple time series of strain monitoring data.Also,the discussion analysis with a classical baseline and an ablation experiment was conducted to verify the effectiveness of the prediction model.As the results indicate,the proposed model shows obvious superiority in predicting the future mechanical behaviors of structures.As a case study,the presented model was applied to the Nanjing Dinghuaimen tunnel to predict the stain variation on a different time scale in the future.
基金financially supported by the Natural Science Foundation of China(52071065)the Fundamental Research Funds for the Central Universities(N2007007)the National Key R&D Program of China(2016YFB-0301201)。
文摘The grain size of TiAl alloy castings prepared by traditional casting process is coarse,thus showing poor mechanical properties.In this study,a new type of high performance Ti-46Al alloy tube prepared by vacuum centrifugal casting technology was introduced.This research comprehensively examined the influence of pouring time on the microstructure and mechanical performance of the castings,employing both experimental approaches and ProCast simulation methodologies.The findings indicate that prolonging the pouring time facilitates a microstructural evolution from coarse columnar grains to refined equiaxed grains.Under the condition of pouring temperature of 1,600℃,rotation speed of 800 r·min^(-1) and pouring time of 6 s,the tensile strength of Ti-46Al alloy at room temperature reaches 650 MPa,and the tensile strength at 800℃ reaches 705 MPa,which is significantly higher than that of traditional as-cast Ti-Al alloy.
基金supported by National Natural Science Foundation of China(No.52025055 and 52275571)Basic Research Operation Fund of China(No.xzy012024024).
文摘Tilted metasurface nanostructures,with excellent physical properties and enormous application potential,pose an urgent need for manufacturing methods.Here,electric-field-driven generative-nanoimprinting technique is proposed.The electric field applied between the template and the substrate drives the contact,tilting,filling,and holding processes.By accurately controlling the introduced included angle between the flexible template and the substrate,tilted nanostructures with a controllable angle are imprinted onto the substrate,although they are vertical on the template.By flexibly adjusting the electric field intensity and the included angle,large-area uniform-tilted,gradient-tilted,and high-angle-tilted nanostructures are fabricated.In contrast to traditional replication,the morphology of the nanoimprinting structure is extended to customized control.This work provides a cost-effective,efficient,and versatile technology for the fabrication of various large-area tilted metasurface structures.As an illustration,a tilted nanograting with a high coupling efficiency is fabricated and integrated into augmented reality displays,demonstrating superior imaging quality.
基金supported by the Research Project on Strengthening the Construction of an Important Ecological Security Barrier in Northern China by Higher Education Institutions in the Inner Mongolia Autonomous Region(STAQZX202313)the Inner Mongolia Autonomous Region Education Science‘14th Five-Year Plan’2024 Annual Research Project(NGJGH2024635).
文摘Vacancy defects,as fundamental disruptions in metallic lattices,play an important role in shaping the mechanical and electronic properties of aluminum crystals.However,the influence of vacancy position under coupled thermomechanical fields remains insufficiently understood.In this study,transmission and scanning electron microscopy were employed to observe dislocation structures and grain boundary heterogeneities in processed aluminum alloys,suggesting stress concentrations and microstructural inhomogeneities associated with vacancy accumulation.To complement these observations,first-principles calculations and molecular dynamics simulations were conducted for seven single-vacancy configurations in face-centered cubic aluminum.The stress response,total energy,density of states(DOS),and differential charge density were examined under varying compressive strain(ε=0–0.1)and temperature(0–600 K).The results indicate that face-centered vacancies tend to reduce mechanical strength and perturb electronic states near the Fermi level,whereas corner and edge vacancies appear to have weaker effects.Elevated temperatures may partially restore electronic uniformity through thermal excitation.Overall,these findings suggest that vacancy position exerts a critical but position-dependent influence on coupled structure-property relationships,offering theoretical insights and preliminary experimental support for defect-engineered aluminum alloy design.
基金This study is financed by the European Union-NextGenerationEU,through the National Recovery and Resilience Plan of the Republic of Bulgaria,Project No.BG-RRP-2.013-0001.
文摘Covert timing channels(CTC)exploit network resources to establish hidden communication pathways,posing signi cant risks to data security and policy compliance.erefore,detecting such hidden and dangerous threats remains one of the security challenges. is paper proposes LinguTimeX,a new framework that combines natural language processing with arti cial intelligence,along with explainable Arti cial Intelligence(AI)not only to detect CTC but also to provide insights into the decision process.LinguTimeX performs multidimensional feature extraction by fusing linguistic attributes with temporal network patterns to identify covert channels precisely.LinguTimeX demonstrates strong e ectiveness in detecting CTC across multiple languages;namely English,Arabic,and Chinese.Speci cally,the LSTM and RNN models achieved F1 scores of 90%on the English dataset,89%on the Arabic dataset,and 88%on the Chinese dataset,showcasing their superior performance and ability to generalize across multiple languages. is highlights their robustness in detecting CTCs within security systems,regardless of the language or cultural context of the data.In contrast,the DeepForest model produced F1-scores ranging from 86%to 87%across the same datasets,further con rming its e ectiveness in CTC detection.Although other algorithms also showed reasonable accuracy,the LSTM and RNN models consistently outperformed them in multilingual settings,suggesting that deep learning models might be better suited for this particular problem.
基金supported by the National Key R&D Program of China(2020YFA0712901).
文摘We study age-structured branching models with reproduction law depending on the remaining lifetime of the parent. The lifespan of an individual is determined at its birth and its remaining lifetime decreases at the unit speed. The models, without or with immigration, are constructed as measure-valued processes by pathwise unique solutions of stochastic equations driven by time-space Poisson random measures. In the subcritical branching case, we give a sufficient condition for the ergodicity of the process with immigration. Two large number laws and a central limit theorem of the occupation times are proved.
基金Supported by the National Natural Science Foundation of China(61079013)the Natural Science Fund Project in Jiangsu Province(BK2011737)~~
文摘According to the failure characteristics of aircraft structure, a delay-time model is an effective method to optimize maintenance for aircraft structure. To imitate the practical situation as much as possible, imperfect inspections, thresholds and repeated intervals are concerned in delay-time models. Since the suggestion by the existing delay-time models that the inspections are implemented in an infinite time span lacks practical value, a de- lay-time model with imperfect inspection within a finite time span is proposed. In the model, the nonhomogenous Poisson process is adopted to obtain the renewal probabilities between two different successive inspections on de- fects or failures. An algorithm is applied based on the Nelder-Mead downhill simplex method to solve the model. Finally, a numerical example proves the validity and effectiveness of the model.
基金Project(ZJY0605-02) supported by the Natural Science Foundation of Heilongjiang Province,ChinaProject(310703002) supported by the National Research Foundation of Korea(NRF) grant funded Korea Government
文摘A new β-Ti based Ti35Nb2.5Sn/10 hydroxyapitite（HA） biocompatible composite was fabricated by mechanical milling and pulsed current activated sintering（PCAS）.The microstructures of Ti35Nb2.5Sn/10HA powder particles and composites sintered from the milled powders were studied.Results indicated that α-Ti phase began to transform into β-Ti phase after the powders were mechanically milled for 8 h.After mechanical milling for 12 h,α-Ti completely transformed into β-Ti phase,and the ultra fine Ti35Nb2.5Sn/10HA composite powders were obtained.And ultra fine grain sized Ti35Nb2.5Sn/10HA sintered composites were obtained by PCAS.The hardness and relative density of the sintered composites both increased with increasing the ball milling time.
文摘In this paper, a new method of time reversal for defect diagnosis of concealed structure has been proposed based on the detecting technique of structure acoustic wave and the theory of time reversal. The time reversal recurrence formula for detecting the acoustic wave speed constitution of concealed structures with bilevel asynchronous test has been established. The wave speed constitution can be reconstructed in 2 D graticule form by means of this method. The result of model test shows the method is valid.
文摘In this paper, a predator -prey model with stage structure and double time delays in pollution environment is modeled. By using comparison theorem of impulsive differential equation, dynamics behaviors of the system is analysised. We prove that the pest-extinction solution of the system is the globally attractive for R 1 <1.
基金Supported by Project Provincial Natural Science Foundation of Hunan （09J J3126） The Doctoral Research Activating Fund of Xiangtan University （09QDZ13, 10QDZ04）
文摘In the procedure of coal industry production, the losses of the persons and economy caused by the gas explosion accidents are most serious, therefore, prevention and control of the gas explosion accident of the coal mines is an important issue needed to be solved urgently in the safety production work of our coal mines. The characteristic of time structure variation index characteristic was analyzed about gas concentration sequence of three measure points in the NO. 1I 1024 working face. It was found that the value of time variation about three measure points was mostly 1〈δ≤1.5, and gas emission presented consistently strong-clustering state twice, and the value of time variation presented continuous variation state in the active stage of gas concentration. Complex characteristics of the value indicated gas emission was continuously variable in time or space and presented the complex nonlinear characteristics. So the characteristic about gas emission system was correctly depicted and analyzed to gas emission system according to the relation of its state variation and essential of nonlinear system. The result also provided reliable warranty for its continued nonlinear research on gas emission.
文摘A time domain finite element method （FEM） for the analysis of transient elastic response of a very large floating structure （VLFS） subjected to arbitrary time-dependent external loads is presented. This method is developed directly in time domain and the hydrodynamic problem is formulated based on linear, inviscid and slightly compressible fluid theory and the structural response is analyzed on the thin plate assumption. The time domain finite element procedure herein is validated by comparing numerical results with available experimental data. Finally, the transient elastic response of a pontoon-type VLFS under the landing of an airplane is computed by the proposed time domain FEM. The time histories of the applied force and the position and velocity of an airplane during landing are modeled with data from a Boeing 747-400 jumbo jet.
基金a sub-project entitled"Strong Earthquake Trend Assessment of the Jiashi-Bachu and the Tianshan,Xinjiang Areas (Grant No.200333116-06)"under the project of "The MS6.8 Jiashi-Bachu, Xinjiang Earthquakesthe Strong Earthquake Trendin the Future" of the key science and technology research program of Xinjiang Uygur Autonomous Region
文摘In 1997 - 2003, 27 earthquakes with M≥ 5.0 occurred in the Jiashi-Bachu area of Xinjiang. It was a rare strong earthquake swarm activity. The earthquake swarm has three time segments of activity with different magnitudes in the years 1997, 1998 and 2003. In different time segments, the seismic activity showed strengthenin-qguiet changes in various degrees before earthquakes with M ≥ 5.0. In order to delimitate effectively the precursory meaning of the clustering （strengthening） quiet change in sequence and to seek the time criterion for impending prediction, the nonlinear characteristics of seismic activity have been used to analyze the time structure characteristics of the earthquake swarm sequence, and further to forecast the development tendency of earthquake sequences in the future. Using the sequence catalogue recorded by the Kashi Station, and taking the earthquakes with Ms≥ 5.0 in the sequence as the starting point and the next earthquake with Ms = 5.0 as the end, statistical analysis has been performed on the time structure relations of the earthquake sequence in different stages. The main results are as follows： （1） Before the major earthquakes with M ≥ 5.0 in the swarm sequence, the time variation coefficient （δ-value） has abnormal demonstrations to different degrees. （2） Within 10 days after δ= 1, occurrence of earthquakes with M ≥ 5.0 in the swarm is very possible. （3） The time variation coefficient has three types of change. （4） The change process before earthquakes with M5.0 is similar to that before earthquakes with M6.0, with little difference in the threshold value. In the earthquake swarm sequence, it is difficult to delimitate accurately the attribute of the current sequences （foreshock or aftershock sequence） and to judge the magnitude of the follow-up earthquake by δ-value. We can only make the judgment that earthquakes with M5.0 are likely to occur in the sequence. （5） The critical clustering characteristics of the sequence are hierarchical. Only corresponding to a certain magnitude can the sequence have the variation state of critical clustering. （6） The coefficient of the time variation has a clear meaning in physics. After the clustering-quiet state of earthquake activity has appeared, it can describe clearly the randomness of the seismogenic system. Furthermore, it can efficiently clarify whether or not the clustering quiescence variation is of some prognostic meaning. In the case that the earthquake frequency attenuation is essentially normal （h 〉 1 ） and there is no remarkable clustering-quiescence state, it is still possible to discover the abnormal change of the sequence from the time variation coefficient. On the contrary, in the later period of swarm activity, after the appearance of many seismic quiescence phenomena, this coefficient did not appear abnormally, even when h 〈 1, suggesting that the δ-value diagnosis is more universal.
基金Funded by the Guangxi Natural Science Foundation(No.2010GXNSFD013007)
文摘The 0.6 mol% CuO-doping 0.996(0.95 Na_(0.5)K_(0.5)NbO_3-0.05 LiSbO_3)-0.004 FeBiO_3(KNN-LSBF-CuO) piezoelectric ceramics were synthesized by a solid-state reaction technique, and the structure and piezoelectric properties dependence of sintering time in KNN-LS-BF-CuO ceramics were studied. It is found that all the samples sintered for various time are perovskite structure mixed with orthorhombic symmetry phase and tetragonal phase, but the sintering time has significant influences on the crystalline and properties. When the sintering time increases from 2 hours to 6 hours, the grain of KNN-LS-BF-CuO ceramics becomes more homogeneous and more tight-arrangement. The experimental results reveal that the longer sintering time than 4 hours is beneficial for improving partial properties, such as d_(33), tgδ, and Q_m, but is adverse to ε_r and k_p, the KNNLS-BF-CuO ceramics with optimum properties can be synthesized for 6 hours at 1 060 ℃.
文摘In this study,the effect of decarburization annealing temperature and time on the carbon content,microstructure,and texture of grain-oriented pure iron was investigated by optical microscopy and scanning electron microscopy with electron-backscatter diffraction. The results showed that the efficiency of decarburization dramatically increased with increasing decarburization temperature. However,when the annealing temperature was increased to 825°C and 850°C,the steel's carbon content remained essentially unchanged at 0.002%. With increasing decarburization time,the steel's carbon content generally decreased. When both the decarburization temperature and time were increased further,the average grain size dramatically increased and the number of fine grains decreased; meanwhile,some relatively larger grains developed. The main texture types of the decarburized sheets were approximately the same: {001}<110> and {112~115}<110>,with a γ-fiber texture. Furthermore,little change was observed in the texture. Compared with the experimental sheets,the texture of the cold-rolled sheet was very scattered. The best average magnetic induction(B_(800)) among the final products was 1.946 T.
基金Supported by the National Natural Science Foundation of China(61273160)the Natural Science Foundation of Shandong Province of China(ZR2011FM014)+1 种基金the Doctoral Fund of Shandong Province(BS2012ZZ011)the Postgraduate Innovation Funds of China University of Petroleum(CX2013060)
文摘Kernel independent component analysis(KICA) is a newly emerging nonlinear process monitoring method,which can extract mutually independent latent variables called independent components(ICs) from process variables. However, when more than one IC have Gaussian distribution, it cannot extract the IC feature effectively and thus its monitoring performance will be degraded drastically. To solve such a problem, a kernel time structure independent component analysis(KTSICA) method is proposed for monitoring nonlinear process in this paper. The original process data are mapped into a feature space nonlinearly and then the whitened data are calculated in the feature space by the kernel trick. Subsequently, a time structure independent component analysis algorithm, which has no requirement for the distribution of ICs, is proposed to extract the IC feature.Finally, two monitoring statistics are built to detect process faults. When some fault is detected, a nonlinear fault identification method is developed to identify fault variables based on sensitivity analysis. The proposed monitoring method is applied in the Tennessee Eastman benchmark process. Applications demonstrate the superiority of KTSICA over KICA.
基金This work was supported by the National Natural Science Foundation of China (No.60274099) and the Foundation of Key Laboratory of Process Industry Automation, Ministry of Education
文摘Two approximation laws of sliding mode for discrete-time variable structure control systems are proposed to overcome the limitations of the exponential approximation law and the variable rate approximation law. By applying the proposed approximation laws of sliding mode to discrete-time variable structure control systems, the stability of origin can be guaranteed, and the chattering along the switching surface caused by discrete-time variable structure control can be restrained effectively. In designing of approximation laws, the problem that the system control input is restricted is also considered, which is very important in practical systems. Finally a simulation example shows the effectiveness of the two approximation laws proposed.
