Dispatched by the Chinese government,a multidisciplinary team of 30 researchers collaborated with a team from Myanmar to conduct a 14-day on-site investigation.The work encompassed seismic intensity assessments,field ...Dispatched by the Chinese government,a multidisciplinary team of 30 researchers collaborated with a team from Myanmar to conduct a 14-day on-site investigation.The work encompassed seismic intensity assessments,field surveys,and loss evaluations.The paper focuses on the intensity distribution and structural damage characteristics of the 2025 M7.9 Myanmar earthquake,yielding the following key findings.(1)The seismogenic fault rupture propagated in a nearly N-S direction,with a surface rupture length of approximately 450 km.The seismic impact zone exhibited an elongated N-S distribution and a shorter E-W span,distributed like a belt around the seismogenic fault.(2)Within the seismic impact zones,existing buildings comprised five primary structural types,with timber(bamboo)structures constituting the largest proportion(≈80%in rural areas,≈50%in urban areas).The relatively low disaster losses and casualties were primarily attributable to the good seismic performance and low damage ratio of timber(bamboo)structures across varying intensity zones.(3)An anomalous zone of intensityⅨwas located at the boundary between intensityⅥandⅦregions in Nay Pyi Taw.Here,ridge topography combined with soft soil layers significantly amplified ground motion,exacerbating structural damage.(4)Directional effects of ground motion were observed,with the structural damage phenomena and peak ground acceleration(PGA)values in the N-S direction exceeding those in the E-W direction.This validates that the maximum PGA distribution of strike-slip fault earthquakes aligns with the fault strike.The research is expected to provide technical support for post-disaster reconstruction planning,site selection,and disaster mitigation strategies in Myanmar.展开更多
Finger-joint lumber is a sustainable building product commercialized as a structural solution for beams,pillars and other thin flat load-bearing elements.This study aims to study finger-joint lumber and its industry t...Finger-joint lumber is a sustainable building product commercialized as a structural solution for beams,pillars and other thin flat load-bearing elements.This study aims to study finger-joint lumber and its industry to promote this engineered wood product.The first research stage assessed the collection of publications on fingerjoint lumber available globally,in which a structured protocol was developed to prospect studies based on two complementary methodologies:PRISMA 2020 using Scopus and Web of Science databases,and Snowball using both forward and backward models to complete with additional literature.The second research stage assessed finger-joint lumber manufacturers,in which companies were globally prospected using Google search engine and their corporate websites were profoundly analyzed using a structured script to collect information.Literary approaches have provided structural performance and bonding quality of finger-jointing.In the review,we provide a global overview and data regarding the current stage and future directions of finger-joint lumber for industrialized construction.Regarding this structural product,we review the main resources,material preparation and processing,and automated production.Mainly active in Europe and already present in 38 nations across five continents,we survey a finger-joint lumber industry comprising 186 producers controlling 214 manufacturing operations worldwide.The vast majority of this industry has exported linear engineered solutions in different dimensions,certified as to compliance with the origins of their bioresources and the European Union requirements,to markets exposed to 24 languages in order to meet commercial applications such as single-story houses,townhouses,roof structures,and hangars.展开更多
Sessile oak(Quercus petraea(Matt.)Liebl.)is widely distributed across most of Europe particularly the hills and lower mountain ranges,so is considered“the oak of the mountains”.This species grows on a wide variety o...Sessile oak(Quercus petraea(Matt.)Liebl.)is widely distributed across most of Europe particularly the hills and lower mountain ranges,so is considered“the oak of the mountains”.This species grows on a wide variety of soils and at altitudes ranging from sea level to 2200 m,especially in Atlantic and sub-Mediterranean climates,and it is sensitive to low winter temperatures,early and late frosts,as well as high summer temperatures.Sessile oak forms both pure and mixed stands especially with broadleaves such as European beech,European hornbeam,small-leaved lime and Acer spp.These form the understorey of sessile oak stands,promoting the natural shedding of lower branches of the oak and protecting the trunk against epicormic branches.Sessile oak is a long-lived,light-demanding and wind-firm species,owing to its taproot and heart-shaped root system.Its timber,one of the most valuable in Europe,is important for fur-niture-making(both solid wood and veneer),construction,barrels,railway sleepers,and is also used as fuelwood.It is one of the few major tree species in Europe that is regener-ated by seed(naturally or artificially)and by stump shoots in high forest,coppice-with-standards and coppice forests.Sessile oak forests are treated in both regular and irregular systems involving silvicultural techniques such as uniform shelterwood,group shelterwood,irregular shelterwood,irregular high forest,coppice-with-standards and simple coppice.Young naturally regenerated stands are managed by weeding,release cutting and cleaning-respacing,keeping the stands quite dense for good natural pruning.Plantations are based on(1)2-4-year old bare-root or container-grown seedlings produced in nurseries using seeds from genetic resources,seed stands and seed orchards.The density of sessile oak plantations(mostly in rows,but also in clusters)is usually between 4000 and 6000 ind.ha^(−1).Sessile oak silviculture of mature stands includes crown thinning,focus-ing on final crop trees(usually a maximum of 100 ind.ha^(−1))and targeting the production of large-diameter and high quality trees at long rotation ages(mostly over 120 years,sometimes 250-300 years).In different parts of Europe,conversion of simple coppices and coppice-with-standards to high forests is continuing.Even though manage-ment of sessile oak forests is very intensive and expensive,requiring active human intervention,the importance of this species in future European forests will increase in the con-text of climate change due to its high resistance to distur-bance,superior drought tolerance and heat stress resistance.展开更多
The application of mass timber elements in different structures has gained publicity over the last few years,pri-marily due to climate change adaptation policies and net zero carbon targets.Timber is a renewable const...The application of mass timber elements in different structures has gained publicity over the last few years,pri-marily due to climate change adaptation policies and net zero carbon targets.Timber is a renewable construction material that can outperform other building materials regarding environmental impact.However,when used in seismically active regions,its application has been limited due to the uncertainties on their seismic behaviour in respect with different design standards and limited ductility in conventional connections.Conventional timber connections typically suffer from stiffness and strength degradation under cyclic loads.Their repairability is also low due to permanent damage in the fasteners and the associated crushing in the wood fibres.The use of friction connections can be an efficient way to mitigate these issues.They offer many advantages as they are economical and yet provide a high level of reliable and continuous energy dissipation.In recent years,a new generation of friction connections has been developed that can provide self-centring behaviour(i.e.,the ability of the structure to return to its original position at the end of an earthquake).However,how these connections perform compared to a mass timber system with conventional timber connections is still unknown.Several studies in the literature have suggested that these connections can enhance the performance of mass timber structures.However,the seismic performance of such systems specifically in terms of base shear,response drifts and response accelerations-has not been thoroughly investigated.This paper examines various design aspects of conventional friction connections and self-centring friction connections,providing insights into their differences concerning key seismic performance indicators.It compares the seismic performance of mass timber buildings equipped with both solutions,highlighting their advantages and limitations and drawing conclusions based on the results.The key findings are that friction connections can provides a superior seismic performance for timber structures.However,that may need to be combined with a parallel system avoid residual displacements.展开更多
Exotic tree species,though widely used in forestry and restoration projects,pose great threats to local ecosystems.They need to be replaced with native species from natural forests.We hypothesized that natural forests...Exotic tree species,though widely used in forestry and restoration projects,pose great threats to local ecosystems.They need to be replaced with native species from natural forests.We hypothesized that natural forests contain large,fast-growing,dominant native tree species that are suitable for specific topographic conditions in forestry.We tested this hypothesis using data from a 50-ha forest dynamics plot in subtropical China.We classified the plot into the ridge,slope,and valley habitats and found that 34/87 species had significant associations with at least one topographic habitat.There were 90 tree species with a maximum diameter≥30 cm,and their abundances varied widely in all habitat types.In all habitat types,for most species,rate of biomass gain due to recruitment was<1%of its original biomass,and rate of biomass gain due to tree growth was between 1 and 5%of its original biomass.For most species,biomass loss due to tree mortality was not significantly different than biomass gain due to recruitment,but the resulting net biomass increment rates did not significantly differ from zero.The time required to reach a diameter of 30 cm from 1 cm diameter for Altingia chinensis in the slope habitat,for Quercus chungii and Morella rubra in the ridge habitat and for Castanopsis carlesii in all habitats could be as short as 30 years in our simulations based on actual distributions of tree growth observed in the forest.Principal component analyses of maximum diameter,abundance and net biomass increment rates suggested several species were worthy of further tests for use in forestry.Our study provides an example for screening native tree species from natural forests for forestry.Because native tree species are better for local ecosystems,our study will also contribute to biodiversity conservation in plantations.展开更多
Platform-style construction is a widely recognized and well-established approach among engineers and developers for multi-story mass timber buildings.This construction method offers many advantages,such as rapid assem...Platform-style construction is a widely recognized and well-established approach among engineers and developers for multi-story mass timber buildings.This construction method offers many advantages,such as rapid assembly,an excellent strength-to-weight ratio,and appealing aesthetic features.In a platform-type construction,each story is constructed by placing the floor panels on top of the load-bearing wall,creating a platform for the level above.Although this method offers numerous advantages,recent research findings have revealed that cross-laminated(CLT)platform buildings with conventional connections,such as wall-to-floor hold-down brackets and shear connectors with nails and screws,are prone to experience a high degree of damage under design-level earthquakes.Consequently,conventional connections in platform-type construction are vulnerable to more damage under aftershocks and do not meet the damage avoidance requirements of seismic design.This paper introduces an innovative floor-to-wall connection for a platform-type low-rise mass timber building that mitigates the limitations of conventional connections.The effectiveness of the proposed connection has been investigated,and the seismic performance of the system,which incorporates the proposed connection,has been outlined in this paper.A numerical model with an innovative inter-story isolation system is developed in ETABS,and the seismic performance of the isolated structure was evaluated using Response Spectrum Analysis(RSA)and Nonlinear Time History Analysis(NLTHA).This study revealed that inter-story isolation systems significantly reduced the seismic demands on the mass timber components,demonstrating the system’s ability to dissipate seismic energy.Additionally,the system displayed effective energy dissipation while exhibiting self-centering behaviour.展开更多
As iconic structures in Dong ethnic villages of Guizhou,drum towers hold significant cultural and architectural value.However,research on their mechanical behavior,particularly the mechanical performance of their join...As iconic structures in Dong ethnic villages of Guizhou,drum towers hold significant cultural and architectural value.However,research on their mechanical behavior,particularly the mechanical performance of their joints,remains limited,with numerical simulation studies lagging behind theoretical and experimental investigations.This study first establishes an orthotropic elastoplastic constitutive model for timber based on experimental data from Chuandou-style timber structures,determining key parameters such as elastic modulus,shear strength,and plastic strain.Subsequently,a refined finite element model was established using ABAQUS,and its reliability was validated through comparative analysis of stress nephograms,skeleton curves,and other key outcomes with experimental data.The findings provide valuable references for engineering design.展开更多
The tropical timber trade faces significant sustainability challenges,including deforestation,illegal logging,and inadequate traceability.Inaccurate species identification further complicates these issues,leading to u...The tropical timber trade faces significant sustainability challenges,including deforestation,illegal logging,and inadequate traceability.Inaccurate species identification further complicates these issues,leading to unreliable trade statistics and enforcement challenges.The Lacey Act Amendment(LAA)of 2008 mandated declaring scientific names for timber shipments entering the United States.Therefore,this study assessed the implementation of the LAA using data obtained through a Freedom of Information Act request to the United States Department of Agriculture-Animal and Plant Health Inspection Service for 4 tropical timber species including Keruing,Meranti,Acajou d’Afrique,and Mahogany from Indonesia,Malaysia,Brazil,Philippines,Cameroon,Ghana,Congo,Cote d’Ivoire,and Bolivia,with high rates of illegal logging.This study showed that the United States imported 49 species of Keruing species group,126 species of Meranti species group,6 species of Acajou d’Afrique species group,and 2 species of Mahogany species group during 2017-2023.Despite mandatory declarations,approximately 14.60%of timber import records lacked species-specific names.Conservation assessments identified 37 species of Keruing species group and 68 species of Meranti species group listed as threatened by the International Union for Conservation of Nature(IUCN)but absent from the Convention on International Trade in Endangered Species of Wild Fauna and Flora(CITES).Moreover,the principal component analysis(PCA)indicated that the first principal component was primarily driven by import value and import volume,reflecting the overall trade prominence,while the second principal component captured temporal pattern through import year.Further,this study developed a Trade-Adjusted Conservation Priority Index(TACPI)that integrated conservation status with trade prominence to prioritize species at risk.Species with high TACPI scores,such as Dipterocarpus coriaceus and Shorea balangeran,were identified as urgently needing regulatory focus.To strengthen sustainable trade and conservation,it is recommended to enforce the LAA more strictly,expand timber identification technologies,and mandate key supplier countries,who are the CITES’signatories,to list high-risk species in the CITES appendices.展开更多
The paper presents a method of using single neuron adaptive PID control for adjusting system or servo system to implement timber drying process control, which combines the thought of parameter adaptive PID control and...The paper presents a method of using single neuron adaptive PID control for adjusting system or servo system to implement timber drying process control, which combines the thought of parameter adaptive PID control and the character of neural network on exactly describing nonlinear and uncertainty dynamic process organically. The method implements functions of adaptive and self-learning by adjusting weighting parameters. Adaptive neural network can make some output trail given hoping value to decouple in static state. The simulation result indicates the validity, veracity and robustness of the method used in the timber drying process展开更多
The mechanical properties of the monodirectional Gutou mortise-tenon joints of the ancient Chinese traditional timber buildings in the Yangtze River region were studied using the experimental method. Three monodirecti...The mechanical properties of the monodirectional Gutou mortise-tenon joints of the ancient Chinese traditional timber buildings in the Yangtze River region were studied using the experimental method. Three monodirectional Gutou mortise-tenon joints were designed according to the actual configurations. The failure modes,the hysteretic curves,the skeleton curves, the rotation rigidities, and the energy dissipation capacity of this type of mortise-tenon joints under the low cyclic reversed loading were obtained. The results show that the hysteretic curves of the monodirectional Gutou mortise-tenon joints appear to be Z shape and have obvious pinch effects. During the process of the test,these mortisetenon joints pass orderly through the elastic stage,the yield stage and the failure stage. The energy dissipation capacity of these mortise-tenon joints generally decreases with the increase in the rotation angle. The equivalent viscous damping coefficients of the monodirectional Gutou mortise-tenon joints are between 0. 161 and 0. 193. The results can provide the theoretical base for the computing analysis and repair design of Chinese traditional timber buildings in the Yangtze River region.展开更多
In the past, utilization of bamboo resources in China has been traditionally dominated by direct consumption of local farmers as minor forest products with weak linkage with market. In recent years, the over-supply of...In the past, utilization of bamboo resources in China has been traditionally dominated by direct consumption of local farmers as minor forest products with weak linkage with market. In recent years, the over-supply of grains and rapid degradation of agricultural environment call for alternative crops that can be developed through integrating the environmental plantation with the market demands. Closely associated with forestry and agriculture, bamboo is able to deal with the new challenges which Chinas agriculture is facing. Of 534 documented bamboo species in China, 153 species produce edible-shoots and of which 56 species are recommended for agricultural plantation; 139 species provide timbers and of which 58 species recommended; 116 species can be splited as good strips for weaving and of which 22 species recommended; 88 species are considered as garden bamboos and of which 34 species recommended; 45 species are able to produce paper pulp and of which 18 species recommended.展开更多
Based on inspecting and investigating the situation of biological hazards of ancient architecture such as north-south building,Fuxi temple and Yuquan Temple,the disease kinds,their damaging ranges and hazard degrees w...Based on inspecting and investigating the situation of biological hazards of ancient architecture such as north-south building,Fuxi temple and Yuquan Temple,the disease kinds,their damaging ranges and hazard degrees were recorded.The results showed that timber structures had some problems such as colored drawing of purlin post,Fang,bucket arches had fallen off;rot,infesting,color spot,sediments on the surface,rupture,warp,breeding plant etc.展开更多
This article, by using mathematical expressions, offers a scientific framework for understanding how the grading system of Qing′s structural carpentry determines the design and construction in the grand style timber...This article, by using mathematical expressions, offers a scientific framework for understanding how the grading system of Qing′s structural carpentry determines the design and construction in the grand style timber architecture.The Qing′s grand style timber structure, which is ready for prefabrication and assembly, is extremely hierarchical oriented and significantly standardized. The general procedure in designing a grand style timber structure is to start with the grade that defines the basic module (dou kou); next comes with the number of bracket set (cuan), the number of longitudinal bays and the number of purlins which affect its plan and cross section; thirdly choose a roof type that determines its longitudinal section and the facade as well. A series of formulae are conducted to help depict the layout, cross sectional roof curvature and special longitudinal treatments in 4 sloped and 9 spined roofs respectively.展开更多
Traditional wooden joinery is the craft of connecting wood pieces for buildings or producing utensils by utilizing only the geometry of the components and material properties of the wood,without other materials such a...Traditional wooden joinery is the craft of connecting wood pieces for buildings or producing utensils by utilizing only the geometry of the components and material properties of the wood,without other materials such as glue or metal connectors.In its thousands of years of tradition,this construction technique has achieved high accomplishment in both East Asian and European architectural civilizations.Although sharing the same basic principles,joinery techniques vary between regions and cultures,rooted in the geographical environment,available wood species and their material properties,characteristics of craftsmanship,tools,and structural systems.Wood framing systems from China,Japan,and Western Europe are selected for comparison to assess the relationship between wood joinery and other aspects of building technology.The main conclusions include:in East Asia,the building tradition pays great attention to the design and execution of joinery(sunmao榫卯),making it responsible for multiple functions including architectural mechanics and the stability of the entire frame,which leads to a broader role meant by the term“joint”itself,while in Europe joinery is treated as the“node”or literally“joint”of the structure.Although in both East Asia and Europe wooden joinery serves as an aesthetic factor of the structure,its expression in East Asia is subtle,veiled,and restrained,while in Europe it is explicit and direct.The most important lesson we learn from the study of traditional joinery technology is that it should be seen in the context of the building process as a whole,taking into account geographical environment,material resources,craftsmanship,tools,construction methods,structural form,and the structural system.展开更多
A new model was developed to predict forestland demand of China during the years of 2010-2050 in terms of the concept of forest ecosystem services. On the basis of the relationship between forest ecosystem services an...A new model was developed to predict forestland demand of China during the years of 2010-2050 in terms of the concept of forest ecosystem services. On the basis of the relationship between forest ecosystem services and classified forest management, we hypothesized that the ecological-forest provides ecological services, whereas commercial-forest supplies wood and timber production, and the influences of the growth of population, social-economic development target, forest management methods and the technology changes on forest resources were also taken into account. The prediction reveals that the demand of total forestland of China will be 244.8, 261.2 and 362.2 million ha by the year 2010, 2020 and 2050, respectively. The results demonstrated that China will be confronted with a shortage of forest resources, especially with lack of ecological-oriented forests, in the future. It is suggested that sustainable management of forest resources must be reinforced and more attention should be drown no enhancing the service function of forest ecosystem.展开更多
This study addresses the increasing demand for large-diameter production timber,and considers the time and space variability of half-sib families of Pinus massoniana.Height,diameter at breast height(DBH)and timber vol...This study addresses the increasing demand for large-diameter production timber,and considers the time and space variability of half-sib families of Pinus massoniana.Height,diameter at breast height(DBH)and timber volume of 440 open-pollinated half-sib progeny families were investigated in 14 progeny trials in different years and production regions.An evaluation of the genetic variation of all half-sib families was carried out during the sustainable rapid growth period and individual volumes were characterized as a major index.ANOVA analysis showed that there was considerable variance in the growth traits of most families in different years and on different sites.The variations caused by temporal and spatial changes of the mating system required three selection methods for analysis.The results show that there were differences among the heritabilities of different growth traits by different halfsib progenies.Average heritability values of height,DBH and volume were 0.33,0.34 and 0.36,respectively.Fortyfive superior families were selected in every progeny test,12 were selected in progeny trials by different years and five in different habitat progeny trials.Three superior families(Gui GC553A,Gui GC414A and Gui GC431A)were selected,although in different years and production regions.The genetic gains of timber volume of these selected r families ranged from 1.20 to 47.00%,which could provide a foundation for superior wood property selection and serve as material for seed improvement and extension in surrounding areas.展开更多
Two analytical procedures （Crank＇s method and Dincer＇s method） for porous solid materials were reevaluated and used to determine moisture diffusion coefficients and moisture transfer coefficients for larch lumber ...Two analytical procedures （Crank＇s method and Dincer＇s method） for porous solid materials were reevaluated and used to determine moisture diffusion coefficients and moisture transfer coefficients for larch lumber subjected to drying. A diffusion-like equation was used to describe drying process data. The lumber was idealized in the modeling as infinite plates. The moisture transport process inside the board was assumed to be one-dimensional. The macroscopic drying kinetics curves of larch timber at particular conditions were determined experimentally. Based on these data, calculation for both the moisture diffusion coefficients and moisture transfer coefficients by the Dincer＇s analytical procedure were made. The dynamic moisture diffusion coefficients by the traditional Crank＇s method were calculated. In general, diffusion coefficients calculated by the Dincer＇s method were all higher than those by Crank＇s method. These results could be due to the differences between two analytical methods and also different characteristics between solid moisture diffusion process and heat transfer process. Therefore the analysis and solution procedures of moisture diffusion differential equations need to be adapted in the future. With drying temperature＇s increasing moisture diffusion coefficient （D） and moisture transfer coefficient （k） increases accordingly. Also the relationships between diffusion coefficients and temperature as well as material moisture contents were analyzed by using Arrhenius equation and bound water transport theory.展开更多
This paper reports on the effect of various micropropagation factors of Gmelina arborea Roxb. through multiple shoot induction. Factors like the source and age of explants, plant growth regulators （PGRs）, media comp...This paper reports on the effect of various micropropagation factors of Gmelina arborea Roxb. through multiple shoot induction. Factors like the source and age of explants, plant growth regulators （PGRs）, media composition, and carbon source affected multiple shoot-ing in the present study. Among all the explants used, only shoot tips derived from one, two, and three week old seedlings could form multiple shoots. Besides, the formation of multiple shoots depended on the con-centration and combination of PGRs. Among all the PGRs, BAP （6-benzylaminopurine） alone gave the highest regeneration efficiency. Simi-larly, IBA （Indole-3-butyric acid） was the most efficient PGR in inducing root formation in the microshoots. Media composition and carbon source also affected the regeneration efficiency. MS （Murashige and Skoog medium） proved to be the best media for regeneration followed by B5, SH （Schenk and Hilderbrandt medium） and WPM （Woody plant medium） in that order. Similarly, among sugars, only sucrose and glucose sup-ported induction of microshoots. Based on this study we recommend the use of glucose in place of sucrose in MS medium for maximum regenera-tion efficiency.展开更多
This study was performed in five villages of Sandwip Upazila, Chittagong district with a view to identify the tree resources, utilization pattern and economic return of major fruit and timber tree species. Information...This study was performed in five villages of Sandwip Upazila, Chittagong district with a view to identify the tree resources, utilization pattern and economic return of major fruit and timber tree species. Information collected from a total of 60 households ranging from marginal, small, medium and large categories. Number of plant species increased with the increase of homestead area. A total of 33 plant species were recorded from the homegarden, of which 19 were fruit and 14 were timber tree species. Considerable number of vegetables was also planted under the shade of the homestead trees. The investment analysis showed that average benefit-cost ratios were greater than one, net present values were positive and internal rate of returns were more than 10%. Long term investment on horticulture and timber tree species is highly profitable if species like Artocarpus heterophyllus, Cocos nucifera, Tectona grandis and Swietenia macrophylla are planted.展开更多
In the megadiverse forests of Southeast Asia, hundreds of timber species are economically important but the population genetics of only a few taxa are known. Cross-specific amplification of microsatellite loci among c...In the megadiverse forests of Southeast Asia, hundreds of timber species are economically important but the population genetics of only a few taxa are known. Cross-specific amplification of microsatellite loci among closely related taxa could enhance our ability to study and manage previously unstudied species. We successfully utilized STMS markers in Shorea platyclados, originally developed for Shorea curtisii. The six primer pairs we tried successfully produced PCR products of expected sizes. The number of alleles observed ranged from 10 to 14 and an average of 12 alleles were detected per locus. A high expected and observed heterozygosity was observed and it ranges from 0.718 to 0.827 among all populations across all six loci tested. Microsatellite DNA markers are highly polymorphic, co-dominant, reproducible, and amenable to high throughput genetic analyses. Overall, the cross- specific amplification of microsatellite loci appears to be complicated by numerous factors. While the approach may be effective for local management and conservation ofpoorly known species, the results must be carefully interpreted.展开更多
基金National Natural Science Foundation of China under Grant No.U2239252National Natural Science Foundation of China under Grant No.52279128Natural Science Foundation of Heilongjiang Province of China under Grant No.YQ2022E013。
文摘Dispatched by the Chinese government,a multidisciplinary team of 30 researchers collaborated with a team from Myanmar to conduct a 14-day on-site investigation.The work encompassed seismic intensity assessments,field surveys,and loss evaluations.The paper focuses on the intensity distribution and structural damage characteristics of the 2025 M7.9 Myanmar earthquake,yielding the following key findings.(1)The seismogenic fault rupture propagated in a nearly N-S direction,with a surface rupture length of approximately 450 km.The seismic impact zone exhibited an elongated N-S distribution and a shorter E-W span,distributed like a belt around the seismogenic fault.(2)Within the seismic impact zones,existing buildings comprised five primary structural types,with timber(bamboo)structures constituting the largest proportion(≈80%in rural areas,≈50%in urban areas).The relatively low disaster losses and casualties were primarily attributable to the good seismic performance and low damage ratio of timber(bamboo)structures across varying intensity zones.(3)An anomalous zone of intensityⅨwas located at the boundary between intensityⅥandⅦregions in Nay Pyi Taw.Here,ridge topography combined with soft soil layers significantly amplified ground motion,exacerbating structural damage.(4)Directional effects of ground motion were observed,with the structural damage phenomena and peak ground acceleration(PGA)values in the N-S direction exceeding those in the E-W direction.This validates that the maximum PGA distribution of strike-slip fault earthquakes aligns with the fault strike.The research is expected to provide technical support for post-disaster reconstruction planning,site selection,and disaster mitigation strategies in Myanmar.
基金supported by the Scientific Grant Agency of the Ministry of Education,Science,Research and Sport of the Slovak Republic(VEGA)with VEGA 1/0228/24 Project and the Cultural and Educational Grant Agency Ministry of Education,Science,Research and Sport of the Slovak Republic(KEGA)with KEGA 017TUKE-4/2024 ProjectBrazilian Federal Agency for Support and Evaluation of Graduate Education(CAPES),with finance code 001.
文摘Finger-joint lumber is a sustainable building product commercialized as a structural solution for beams,pillars and other thin flat load-bearing elements.This study aims to study finger-joint lumber and its industry to promote this engineered wood product.The first research stage assessed the collection of publications on fingerjoint lumber available globally,in which a structured protocol was developed to prospect studies based on two complementary methodologies:PRISMA 2020 using Scopus and Web of Science databases,and Snowball using both forward and backward models to complete with additional literature.The second research stage assessed finger-joint lumber manufacturers,in which companies were globally prospected using Google search engine and their corporate websites were profoundly analyzed using a structured script to collect information.Literary approaches have provided structural performance and bonding quality of finger-jointing.In the review,we provide a global overview and data regarding the current stage and future directions of finger-joint lumber for industrialized construction.Regarding this structural product,we review the main resources,material preparation and processing,and automated production.Mainly active in Europe and already present in 38 nations across five continents,we survey a finger-joint lumber industry comprising 186 producers controlling 214 manufacturing operations worldwide.The vast majority of this industry has exported linear engineered solutions in different dimensions,certified as to compliance with the origins of their bioresources and the European Union requirements,to markets exposed to 24 languages in order to meet commercial applications such as single-story houses,townhouses,roof structures,and hangars.
文摘Sessile oak(Quercus petraea(Matt.)Liebl.)is widely distributed across most of Europe particularly the hills and lower mountain ranges,so is considered“the oak of the mountains”.This species grows on a wide variety of soils and at altitudes ranging from sea level to 2200 m,especially in Atlantic and sub-Mediterranean climates,and it is sensitive to low winter temperatures,early and late frosts,as well as high summer temperatures.Sessile oak forms both pure and mixed stands especially with broadleaves such as European beech,European hornbeam,small-leaved lime and Acer spp.These form the understorey of sessile oak stands,promoting the natural shedding of lower branches of the oak and protecting the trunk against epicormic branches.Sessile oak is a long-lived,light-demanding and wind-firm species,owing to its taproot and heart-shaped root system.Its timber,one of the most valuable in Europe,is important for fur-niture-making(both solid wood and veneer),construction,barrels,railway sleepers,and is also used as fuelwood.It is one of the few major tree species in Europe that is regener-ated by seed(naturally or artificially)and by stump shoots in high forest,coppice-with-standards and coppice forests.Sessile oak forests are treated in both regular and irregular systems involving silvicultural techniques such as uniform shelterwood,group shelterwood,irregular shelterwood,irregular high forest,coppice-with-standards and simple coppice.Young naturally regenerated stands are managed by weeding,release cutting and cleaning-respacing,keeping the stands quite dense for good natural pruning.Plantations are based on(1)2-4-year old bare-root or container-grown seedlings produced in nurseries using seeds from genetic resources,seed stands and seed orchards.The density of sessile oak plantations(mostly in rows,but also in clusters)is usually between 4000 and 6000 ind.ha^(−1).Sessile oak silviculture of mature stands includes crown thinning,focus-ing on final crop trees(usually a maximum of 100 ind.ha^(−1))and targeting the production of large-diameter and high quality trees at long rotation ages(mostly over 120 years,sometimes 250-300 years).In different parts of Europe,conversion of simple coppices and coppice-with-standards to high forests is continuing.Even though manage-ment of sessile oak forests is very intensive and expensive,requiring active human intervention,the importance of this species in future European forests will increase in the con-text of climate change due to its high resistance to distur-bance,superior drought tolerance and heat stress resistance.
文摘The application of mass timber elements in different structures has gained publicity over the last few years,pri-marily due to climate change adaptation policies and net zero carbon targets.Timber is a renewable construction material that can outperform other building materials regarding environmental impact.However,when used in seismically active regions,its application has been limited due to the uncertainties on their seismic behaviour in respect with different design standards and limited ductility in conventional connections.Conventional timber connections typically suffer from stiffness and strength degradation under cyclic loads.Their repairability is also low due to permanent damage in the fasteners and the associated crushing in the wood fibres.The use of friction connections can be an efficient way to mitigate these issues.They offer many advantages as they are economical and yet provide a high level of reliable and continuous energy dissipation.In recent years,a new generation of friction connections has been developed that can provide self-centring behaviour(i.e.,the ability of the structure to return to its original position at the end of an earthquake).However,how these connections perform compared to a mass timber system with conventional timber connections is still unknown.Several studies in the literature have suggested that these connections can enhance the performance of mass timber structures.However,the seismic performance of such systems specifically in terms of base shear,response drifts and response accelerations-has not been thoroughly investigated.This paper examines various design aspects of conventional friction connections and self-centring friction connections,providing insights into their differences concerning key seismic performance indicators.It compares the seismic performance of mass timber buildings equipped with both solutions,highlighting their advantages and limitations and drawing conclusions based on the results.The key findings are that friction connections can provides a superior seismic performance for timber structures.However,that may need to be combined with a parallel system avoid residual displacements.
基金supported by the National Natural Science Foundation of China(31925027,31300455).
文摘Exotic tree species,though widely used in forestry and restoration projects,pose great threats to local ecosystems.They need to be replaced with native species from natural forests.We hypothesized that natural forests contain large,fast-growing,dominant native tree species that are suitable for specific topographic conditions in forestry.We tested this hypothesis using data from a 50-ha forest dynamics plot in subtropical China.We classified the plot into the ridge,slope,and valley habitats and found that 34/87 species had significant associations with at least one topographic habitat.There were 90 tree species with a maximum diameter≥30 cm,and their abundances varied widely in all habitat types.In all habitat types,for most species,rate of biomass gain due to recruitment was<1%of its original biomass,and rate of biomass gain due to tree growth was between 1 and 5%of its original biomass.For most species,biomass loss due to tree mortality was not significantly different than biomass gain due to recruitment,but the resulting net biomass increment rates did not significantly differ from zero.The time required to reach a diameter of 30 cm from 1 cm diameter for Altingia chinensis in the slope habitat,for Quercus chungii and Morella rubra in the ridge habitat and for Castanopsis carlesii in all habitats could be as short as 30 years in our simulations based on actual distributions of tree growth observed in the forest.Principal component analyses of maximum diameter,abundance and net biomass increment rates suggested several species were worthy of further tests for use in forestry.Our study provides an example for screening native tree species from natural forests for forestry.Because native tree species are better for local ecosystems,our study will also contribute to biodiversity conservation in plantations.
基金gratitude to WIDE Trust New Zealand for providing the opportunity and funding for this research,as well as QuakeCoRE,a New Zealand Tertiary Education Commission-funded Centre,for partially funding this research.This is QuakeCoRE,publication number 1013.
文摘Platform-style construction is a widely recognized and well-established approach among engineers and developers for multi-story mass timber buildings.This construction method offers many advantages,such as rapid assembly,an excellent strength-to-weight ratio,and appealing aesthetic features.In a platform-type construction,each story is constructed by placing the floor panels on top of the load-bearing wall,creating a platform for the level above.Although this method offers numerous advantages,recent research findings have revealed that cross-laminated(CLT)platform buildings with conventional connections,such as wall-to-floor hold-down brackets and shear connectors with nails and screws,are prone to experience a high degree of damage under design-level earthquakes.Consequently,conventional connections in platform-type construction are vulnerable to more damage under aftershocks and do not meet the damage avoidance requirements of seismic design.This paper introduces an innovative floor-to-wall connection for a platform-type low-rise mass timber building that mitigates the limitations of conventional connections.The effectiveness of the proposed connection has been investigated,and the seismic performance of the system,which incorporates the proposed connection,has been outlined in this paper.A numerical model with an innovative inter-story isolation system is developed in ETABS,and the seismic performance of the isolated structure was evaluated using Response Spectrum Analysis(RSA)and Nonlinear Time History Analysis(NLTHA).This study revealed that inter-story isolation systems significantly reduced the seismic demands on the mass timber components,demonstrating the system’s ability to dissipate seismic energy.Additionally,the system displayed effective energy dissipation while exhibiting self-centering behaviour.
基金Science and Technology Planning Project of Zunyi City of China(Project No.:Zun Shi Ke He HZ Zi[2022]121)College Students’Innovation and Entrepreneurship Training Program(Project No.:202310664031)+1 种基金Guizhou Provincial First-Class Undergraduate Major“Civil Engineering”(Project No.:Qian Jiao Han[2022]No.61)Guizhou Provincial First-Class Course Construction Project(Project No.:2022JKXX0165,2024JKXN0064)。
文摘As iconic structures in Dong ethnic villages of Guizhou,drum towers hold significant cultural and architectural value.However,research on their mechanical behavior,particularly the mechanical performance of their joints,remains limited,with numerical simulation studies lagging behind theoretical and experimental investigations.This study first establishes an orthotropic elastoplastic constitutive model for timber based on experimental data from Chuandou-style timber structures,determining key parameters such as elastic modulus,shear strength,and plastic strain.Subsequently,a refined finite element model was established using ABAQUS,and its reliability was validated through comparative analysis of stress nephograms,skeleton curves,and other key outcomes with experimental data.The findings provide valuable references for engineering design.
基金United States Endowment for Forestry and Communities in coordination with the Northern Forest Center for partial funding(No.91093)of the project.
文摘The tropical timber trade faces significant sustainability challenges,including deforestation,illegal logging,and inadequate traceability.Inaccurate species identification further complicates these issues,leading to unreliable trade statistics and enforcement challenges.The Lacey Act Amendment(LAA)of 2008 mandated declaring scientific names for timber shipments entering the United States.Therefore,this study assessed the implementation of the LAA using data obtained through a Freedom of Information Act request to the United States Department of Agriculture-Animal and Plant Health Inspection Service for 4 tropical timber species including Keruing,Meranti,Acajou d’Afrique,and Mahogany from Indonesia,Malaysia,Brazil,Philippines,Cameroon,Ghana,Congo,Cote d’Ivoire,and Bolivia,with high rates of illegal logging.This study showed that the United States imported 49 species of Keruing species group,126 species of Meranti species group,6 species of Acajou d’Afrique species group,and 2 species of Mahogany species group during 2017-2023.Despite mandatory declarations,approximately 14.60%of timber import records lacked species-specific names.Conservation assessments identified 37 species of Keruing species group and 68 species of Meranti species group listed as threatened by the International Union for Conservation of Nature(IUCN)but absent from the Convention on International Trade in Endangered Species of Wild Fauna and Flora(CITES).Moreover,the principal component analysis(PCA)indicated that the first principal component was primarily driven by import value and import volume,reflecting the overall trade prominence,while the second principal component captured temporal pattern through import year.Further,this study developed a Trade-Adjusted Conservation Priority Index(TACPI)that integrated conservation status with trade prominence to prioritize species at risk.Species with high TACPI scores,such as Dipterocarpus coriaceus and Shorea balangeran,were identified as urgently needing regulatory focus.To strengthen sustainable trade and conservation,it is recommended to enforce the LAA more strictly,expand timber identification technologies,and mandate key supplier countries,who are the CITES’signatories,to list high-risk species in the CITES appendices.
基金the Key Technologies R&D Program of Harbin (0111211102).
文摘The paper presents a method of using single neuron adaptive PID control for adjusting system or servo system to implement timber drying process control, which combines the thought of parameter adaptive PID control and the character of neural network on exactly describing nonlinear and uncertainty dynamic process organically. The method implements functions of adaptive and self-learning by adjusting weighting parameters. Adaptive neural network can make some output trail given hoping value to decouple in static state. The simulation result indicates the validity, veracity and robustness of the method used in the timber drying process
基金The National Natural Science Foundation of China(No.51138002,51578127)
文摘The mechanical properties of the monodirectional Gutou mortise-tenon joints of the ancient Chinese traditional timber buildings in the Yangtze River region were studied using the experimental method. Three monodirectional Gutou mortise-tenon joints were designed according to the actual configurations. The failure modes,the hysteretic curves,the skeleton curves, the rotation rigidities, and the energy dissipation capacity of this type of mortise-tenon joints under the low cyclic reversed loading were obtained. The results show that the hysteretic curves of the monodirectional Gutou mortise-tenon joints appear to be Z shape and have obvious pinch effects. During the process of the test,these mortisetenon joints pass orderly through the elastic stage,the yield stage and the failure stage. The energy dissipation capacity of these mortise-tenon joints generally decreases with the increase in the rotation angle. The equivalent viscous damping coefficients of the monodirectional Gutou mortise-tenon joints are between 0. 161 and 0. 193. The results can provide the theoretical base for the computing analysis and repair design of Chinese traditional timber buildings in the Yangtze River region.
文摘In the past, utilization of bamboo resources in China has been traditionally dominated by direct consumption of local farmers as minor forest products with weak linkage with market. In recent years, the over-supply of grains and rapid degradation of agricultural environment call for alternative crops that can be developed through integrating the environmental plantation with the market demands. Closely associated with forestry and agriculture, bamboo is able to deal with the new challenges which Chinas agriculture is facing. Of 534 documented bamboo species in China, 153 species produce edible-shoots and of which 56 species are recommended for agricultural plantation; 139 species provide timbers and of which 58 species recommended; 116 species can be splited as good strips for weaving and of which 22 species recommended; 88 species are considered as garden bamboos and of which 34 species recommended; 45 species are able to produce paper pulp and of which 18 species recommended.
文摘Based on inspecting and investigating the situation of biological hazards of ancient architecture such as north-south building,Fuxi temple and Yuquan Temple,the disease kinds,their damaging ranges and hazard degrees were recorded.The results showed that timber structures had some problems such as colored drawing of purlin post,Fang,bucket arches had fallen off;rot,infesting,color spot,sediments on the surface,rupture,warp,breeding plant etc.
文摘This article, by using mathematical expressions, offers a scientific framework for understanding how the grading system of Qing′s structural carpentry determines the design and construction in the grand style timber architecture.The Qing′s grand style timber structure, which is ready for prefabrication and assembly, is extremely hierarchical oriented and significantly standardized. The general procedure in designing a grand style timber structure is to start with the grade that defines the basic module (dou kou); next comes with the number of bracket set (cuan), the number of longitudinal bays and the number of purlins which affect its plan and cross section; thirdly choose a roof type that determines its longitudinal section and the facade as well. A series of formulae are conducted to help depict the layout, cross sectional roof curvature and special longitudinal treatments in 4 sloped and 9 spined roofs respectively.
基金Project supported by the National Natural Science Foundation of China(Grant No.52008194)。
文摘Traditional wooden joinery is the craft of connecting wood pieces for buildings or producing utensils by utilizing only the geometry of the components and material properties of the wood,without other materials such as glue or metal connectors.In its thousands of years of tradition,this construction technique has achieved high accomplishment in both East Asian and European architectural civilizations.Although sharing the same basic principles,joinery techniques vary between regions and cultures,rooted in the geographical environment,available wood species and their material properties,characteristics of craftsmanship,tools,and structural systems.Wood framing systems from China,Japan,and Western Europe are selected for comparison to assess the relationship between wood joinery and other aspects of building technology.The main conclusions include:in East Asia,the building tradition pays great attention to the design and execution of joinery(sunmao榫卯),making it responsible for multiple functions including architectural mechanics and the stability of the entire frame,which leads to a broader role meant by the term“joint”itself,while in Europe joinery is treated as the“node”or literally“joint”of the structure.Although in both East Asia and Europe wooden joinery serves as an aesthetic factor of the structure,its expression in East Asia is subtle,veiled,and restrained,while in Europe it is explicit and direct.The most important lesson we learn from the study of traditional joinery technology is that it should be seen in the context of the building process as a whole,taking into account geographical environment,material resources,craftsmanship,tools,construction methods,structural form,and the structural system.
基金the National Key Technologies R&D Program of China (2006BAD03A09)the National Science Fund of China (40841001)
文摘A new model was developed to predict forestland demand of China during the years of 2010-2050 in terms of the concept of forest ecosystem services. On the basis of the relationship between forest ecosystem services and classified forest management, we hypothesized that the ecological-forest provides ecological services, whereas commercial-forest supplies wood and timber production, and the influences of the growth of population, social-economic development target, forest management methods and the technology changes on forest resources were also taken into account. The prediction reveals that the demand of total forestland of China will be 244.8, 261.2 and 362.2 million ha by the year 2010, 2020 and 2050, respectively. The results demonstrated that China will be confronted with a shortage of forest resources, especially with lack of ecological-oriented forests, in the future. It is suggested that sustainable management of forest resources must be reinforced and more attention should be drown no enhancing the service function of forest ecosystem.
文摘This study addresses the increasing demand for large-diameter production timber,and considers the time and space variability of half-sib families of Pinus massoniana.Height,diameter at breast height(DBH)and timber volume of 440 open-pollinated half-sib progeny families were investigated in 14 progeny trials in different years and production regions.An evaluation of the genetic variation of all half-sib families was carried out during the sustainable rapid growth period and individual volumes were characterized as a major index.ANOVA analysis showed that there was considerable variance in the growth traits of most families in different years and on different sites.The variations caused by temporal and spatial changes of the mating system required three selection methods for analysis.The results show that there were differences among the heritabilities of different growth traits by different halfsib progenies.Average heritability values of height,DBH and volume were 0.33,0.34 and 0.36,respectively.Fortyfive superior families were selected in every progeny test,12 were selected in progeny trials by different years and five in different habitat progeny trials.Three superior families(Gui GC553A,Gui GC414A and Gui GC431A)were selected,although in different years and production regions.The genetic gains of timber volume of these selected r families ranged from 1.20 to 47.00%,which could provide a foundation for superior wood property selection and serve as material for seed improvement and extension in surrounding areas.
文摘Two analytical procedures （Crank＇s method and Dincer＇s method） for porous solid materials were reevaluated and used to determine moisture diffusion coefficients and moisture transfer coefficients for larch lumber subjected to drying. A diffusion-like equation was used to describe drying process data. The lumber was idealized in the modeling as infinite plates. The moisture transport process inside the board was assumed to be one-dimensional. The macroscopic drying kinetics curves of larch timber at particular conditions were determined experimentally. Based on these data, calculation for both the moisture diffusion coefficients and moisture transfer coefficients by the Dincer＇s analytical procedure were made. The dynamic moisture diffusion coefficients by the traditional Crank＇s method were calculated. In general, diffusion coefficients calculated by the Dincer＇s method were all higher than those by Crank＇s method. These results could be due to the differences between two analytical methods and also different characteristics between solid moisture diffusion process and heat transfer process. Therefore the analysis and solution procedures of moisture diffusion differential equations need to be adapted in the future. With drying temperature＇s increasing moisture diffusion coefficient （D） and moisture transfer coefficient （k） increases accordingly. Also the relationships between diffusion coefficients and temperature as well as material moisture contents were analyzed by using Arrhenius equation and bound water transport theory.
文摘This paper reports on the effect of various micropropagation factors of Gmelina arborea Roxb. through multiple shoot induction. Factors like the source and age of explants, plant growth regulators （PGRs）, media composition, and carbon source affected multiple shoot-ing in the present study. Among all the explants used, only shoot tips derived from one, two, and three week old seedlings could form multiple shoots. Besides, the formation of multiple shoots depended on the con-centration and combination of PGRs. Among all the PGRs, BAP （6-benzylaminopurine） alone gave the highest regeneration efficiency. Simi-larly, IBA （Indole-3-butyric acid） was the most efficient PGR in inducing root formation in the microshoots. Media composition and carbon source also affected the regeneration efficiency. MS （Murashige and Skoog medium） proved to be the best media for regeneration followed by B5, SH （Schenk and Hilderbrandt medium） and WPM （Woody plant medium） in that order. Similarly, among sugars, only sucrose and glucose sup-ported induction of microshoots. Based on this study we recommend the use of glucose in place of sucrose in MS medium for maximum regenera-tion efficiency.
文摘This study was performed in five villages of Sandwip Upazila, Chittagong district with a view to identify the tree resources, utilization pattern and economic return of major fruit and timber tree species. Information collected from a total of 60 households ranging from marginal, small, medium and large categories. Number of plant species increased with the increase of homestead area. A total of 33 plant species were recorded from the homegarden, of which 19 were fruit and 14 were timber tree species. Considerable number of vegetables was also planted under the shade of the homestead trees. The investment analysis showed that average benefit-cost ratios were greater than one, net present values were positive and internal rate of returns were more than 10%. Long term investment on horticulture and timber tree species is highly profitable if species like Artocarpus heterophyllus, Cocos nucifera, Tectona grandis and Swietenia macrophylla are planted.
基金financially supported by Texas Tech University in the form of start-up and faculty research enhancement grants
文摘In the megadiverse forests of Southeast Asia, hundreds of timber species are economically important but the population genetics of only a few taxa are known. Cross-specific amplification of microsatellite loci among closely related taxa could enhance our ability to study and manage previously unstudied species. We successfully utilized STMS markers in Shorea platyclados, originally developed for Shorea curtisii. The six primer pairs we tried successfully produced PCR products of expected sizes. The number of alleles observed ranged from 10 to 14 and an average of 12 alleles were detected per locus. A high expected and observed heterozygosity was observed and it ranges from 0.718 to 0.827 among all populations across all six loci tested. Microsatellite DNA markers are highly polymorphic, co-dominant, reproducible, and amenable to high throughput genetic analyses. Overall, the cross- specific amplification of microsatellite loci appears to be complicated by numerous factors. While the approach may be effective for local management and conservation ofpoorly known species, the results must be carefully interpreted.
