Switched-capacitor/flying capacitor(FC)based multilevel converters have been gaining higher attention for their voltage-boosting ability.This feature makes them an attractive solution for renewable energy systems,such...Switched-capacitor/flying capacitor(FC)based multilevel converters have been gaining higher attention for their voltage-boosting ability.This feature makes them an attractive solution for renewable energy systems,such as low-voltage input photovoltaic power systems and electric vehicle systems.However,they usually require more high voltage rating switches and flying capacitors along with boosting capability.Furthermore,they suffer from high pulse currents at the switching transients.Aiming to solve these issues,this article proposes a new self-balancing three-phase five-level inverter based on the switched-capacitor(5L-SCTPNPC),which reduces the dc voltage requirement.The number of active switches is relatively smaller and seven active switches are required per phase.Especially,a soft-charging circuit for FC is designed to limit the impulse charging current.Compared to conventional multilevel inverters,the proposed five-level inverter reduces dc bus voltage by 50%.Significantly,the voltage stress of FC and the switches in parallel with FC are all reduced by 50%in comparison with some existing similar boosting five-level active-neutral-point-clamped(5L-BANPC)inverters.The operating principles,modulation strategy,and the design of the FC and charging inductor are provided in detailly.A comprehensive comparison study has been made to highlight the merits of the proposed inverter.Finally,the simulations and experiments validate the feasibility of the proposed topology.展开更多
Renewable electricity-driven production of value-added sulfur and H_(2)via electrocatalytic H_(2)S decomposition represents a sustainable route to conventional thermocatalysis.Both the electrocatalyst and electrolyte ...Renewable electricity-driven production of value-added sulfur and H_(2)via electrocatalytic H_(2)S decomposition represents a sustainable route to conventional thermocatalysis.Both the electrocatalyst and electrolyte solution strongly impact the H_(2)S decomposition performance.Despite significant progress in developing sophisticated electrocatalysts,a well-designed electrolyte solution in conjunction with industrial catalysts is an attractive strategy to advance the industrialization process of electrocatalytic H_(2)S decomposition,but remains unexplored.Here,for the first time,we design a solid-liquid-gas three-phase indirect electrolysis system based on a kind of CS_(2)-N electrolyte solution and Ni-Mo_(2)C that can efficiently enable H_(2)S decomposition into valuable H_(2)and sulfur.Specifically,the solid-phase Ni-Mo_(2)C as a heterogeneous redox mediator presents excellent electrocatalytic efficiency for the H_(2)S removal efficiency of up to 99%,and the formation of liquid-phase sulfur product(CS_(2)-N electrolyte solution dissolves sulfur,yield up to 95%)with the generation of gas-phase H_(2)product(~1.32 mL min^(-1)),resulting in an interesting three-phase indirect electrolysis system.Remarkably,it enables the scale-up production(~6 g in a batch experiment)of sulfur with continuous operation for 120 h without attenuation.This work may inaugurate a new electrocatalytic H_(2)S decomposition avenue to explore porous metal materials and electrolyte systems in simultaneous production of value-added sulfur and H_(2).展开更多
The transient phenomena of re-oxidation and slag entrapment occurring in the tundish during the ladle change-over process have been proven detrimental to clean steel production.Therefore,an unsteady three-phase turbul...The transient phenomena of re-oxidation and slag entrapment occurring in the tundish during the ladle change-over process have been proven detrimental to clean steel production.Therefore,an unsteady three-phase turbulence model,coupling velocity,temperature,and phase field was established to study the effect of the ladle shroud immersion depth on the slag eye formation,slag entrainment,slag dragging,air dragging,and flow characteristics during the ladle change-over process of a two-strand tundish.The results showed that reducing the immersion depth decreases the high-velocity region area under the slag layer in the quasi-steady process.During the emptying stage,as the molten bath level gradually decreases,the outlet temperature exhibits a trend of initially decreasing and subsequently increasing across all three shroud immersion depths.However,under a 210 mm shroud immersion depth,molten slag and air are dragged into the shroud,forming slag droplets and causing significant fluctuations,with a maximum scalar velocity of 0.0764 m/s at the monitoring point.In the filling stage,air and molten slag are dragged into the molten bath,forming bubbles and slag droplets at an immersion depth of 210 mm.Bubbles are observed within the molten slag layer,which can readily cause an emulsification phenomenon,making it easier to be dragged as slag droplets.Additionally,the slag eye area measured under 210 mm immersion depth at 45 s is 0.303 m^(2),while the maximum scalar velocity of 2.4259 m/s is detected at 12 s.At an immersion depth of 360 mm,the average area of the slag eye is minimized to 0.06268 m2,with corresponding variances of 0.006753,representing the optimal immersion depth.展开更多
For three phase four-wire active power filters （APFs）, several typical power theories and corresponding current reference generation strategies are induced, p-q, d-q, unify power factor （UPF） and instantaneous act...For three phase four-wire active power filters （APFs）, several typical power theories and corresponding current reference generation strategies are induced, p-q, d-q, unify power factor （UPF） and instantaneous active current （IAC） methods are analyzed and compared with each other. The interpretation of active and reactive currents in non-sinusoidal and unbalanced three-phase four-wire systems is given based on the generalized instantaneous reactive power theory. The performance and the characteristic are evaluated, and the application conditions of current reference generation strategies are concluded. Simulation results under different source voltages and loads verify the evaluation result.展开更多
To achieve high power rating and low current harmonics of motor drive,this paper develops a dual three-phase open-winding permanent magnet synchronous motor(DTP-OW-PMSM)drive with the DC-link voltage ratio of 2:1:1.Ba...To achieve high power rating and low current harmonics of motor drive,this paper develops a dual three-phase open-winding permanent magnet synchronous motor(DTP-OW-PMSM)drive with the DC-link voltage ratio of 2:1:1.Based on this topology,this paper proposes a DTP four-level space vector pulse width modulation(DTP-FL SVPWM)strategy.First,two identical three-phase four-level space vector diagrams are constructed and divided.Then,three adjacent vectors nearest to the reference vector in each diagram are selected for the vector synthesis to guarantee high modulation precision and low switching frequency.Furthermore,to avoid the modulation error caused by the voltage deviation,the proposed DTP-FL SVPWM strategy is further optimized through unified duty ratio compensation(UDRC).The effectiveness of the proposed strategy is verified through experiments.展开更多
The growing demand for efficient high-power switching power supplies has spurred interest in advanced topologies.The three-phase VIENNA converter stands out for its high power factor,simplified structure,and robust pe...The growing demand for efficient high-power switching power supplies has spurred interest in advanced topologies.The three-phase VIENNA converter stands out for its high power factor,simplified structure,and robust performance.Current research focuses on its operational principles,control strategies,and behavior under various load conditions.Key considerations include component selection,thermal management,and EMI/EMC optimization.This topology finds applications across renewable energy systems,industrial equipment,telecommunications,and electric vehicle charging infrastructures.Comparative analyses with alternative topologies and cost-benefit evaluations are also addressed.Future developments are expected to emphasize the integration of wide-bandgap devices and advancements in digital control techniques to further enhance efficiency and system performance.展开更多
Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing addit...Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.展开更多
The dual three-phase PMSM(DTP-PMSM)drives have received wide attention at high-power high-efficiency applications due to their merits of high output current ability and copper-loss-free field excitation.Meanwhile,the ...The dual three-phase PMSM(DTP-PMSM)drives have received wide attention at high-power high-efficiency applications due to their merits of high output current ability and copper-loss-free field excitation.Meanwhile,the DTPPMSM drive provides higher fault-tolerant capability for highreliability applications,e.g.,pumps and actuators in aircraft.For high-power drives with limited switching frequencies and highspeed drives with large fundamental frequencies,the ratio of switching frequency to fundamental frequency,i.e.,the carrier ratio,is usually below 15,which would significantly degrade the control performance.The purpose of this paper is to review the recent work on the modulation and control schemes for improving the operation performance of DTP-PMSM drives with low carrier ratios.Specifically,three categories of methods,i.e.,the space vector modulation based control,the model predictive control(MPC),and the optimized pulse pattern(OPP)based control are reviewed with principles and performance.In addition,brief discussions regarding the comparison and future trends are presented for low-carrier-ratio(LCR)modulation and control schemes of DTP-PMSM drives.展开更多
We present the first systematic experimental validation of return-current-driven cylindrical implosion scaling in micrometer-sized Cu and Al wires irradiated by J-class femtosecond laser pulses.Employing XFEL-based im...We present the first systematic experimental validation of return-current-driven cylindrical implosion scaling in micrometer-sized Cu and Al wires irradiated by J-class femtosecond laser pulses.Employing XFEL-based imaging with sub-micrometer spatial and femtosecond temporal resolution,supported by hydrodynamic and particle-in-cell simulations,we reveal how return current density depends precisely on wire diameter,material properties,and incident laser energy.We identify deviations from simple theoretical predictions due to geometrically influenced electron escape dynamics.These results refine and confirm the scaling laws essential for predictive modeling in high-energy-density physics and inertial fusion research.展开更多
In this study,multilayer lamination welding was employed to prepare graphene/copper(Gr/Cu)composite billets from graphene-coated copper foils,followed by multi-pass cold drawing to produce Φ1 mm Gr/Cu composite wires...In this study,multilayer lamination welding was employed to prepare graphene/copper(Gr/Cu)composite billets from graphene-coated copper foils,followed by multi-pass cold drawing to produce Φ1 mm Gr/Cu composite wires.Microstructure and property analyses in both the cold-drawn and annealed states show that the incorporation of graphene significantly improves the ductility and electrical conductivity of the copper wire.After annealing at 350℃ for 30 minutes,the composite wire demonstrates a tensile strength of 270 MPa and an electrical conductivity of 102.74%IACS,both superior to those of pure copper wire under identical conditions.At 150℃,the electrical conductivity of the annealed composite wire reaches 72.60%IACS,notably higher than the 68.19%IACS of pure copper.The results suggest that graphene is uniformly distributed within the composite wire,with minimal impact on conductivity,while effectively refining the copper grain structure to enhance ductility.Moreover,graphene suppresses copper lattice vibrations at elevated temperatures,reducing the rate of conductivity degradation.展开更多
Osmotic energy,existing between the seawater and river water,is a renewable energy source,which can be directly converted into electricity by ion-exchange membranes(IEM).In traditional IEMs,the ion transport channels ...Osmotic energy,existing between the seawater and river water,is a renewable energy source,which can be directly converted into electricity by ion-exchange membranes(IEM).In traditional IEMs,the ion transport channels are formed by nanophase separation of hydrophilic ion carriers and hydrophobic segments.It is difficult to realize high-density ion channels with controlled spatial arrangement and length scale of ion carriers.Herein,we construct high-density 1D ion wires as transmission channels.Through molecular design,hydrophilic imidazole groups and hydrophobic alkyl tails were introduced into the repeat units,which self-assembled into 1D ion transporting core and protecting shell along the main chains.The areal density of the ionic wire arrays is up to~10^(12)cm^(-2),which is the highest value.The ionic wires ensure both high ion flux transport and high selectivity,achieving an ultrahigh-power density of 40.5 W m^(-2)at a 500-fold salinity gradient.Besides,the ionic wire array membrane is well recyclable and antibacterial.The ionic wires provide novel concept for next generation of high-performance membranes.展开更多
Giant magnetoimpedance(GMI)sensors are increasingly employed in modern magnetic sensing technologies.However,improving the GMI performance of magnetic cores remains challenging due to intrinsic limitations in material...Giant magnetoimpedance(GMI)sensors are increasingly employed in modern magnetic sensing technologies.However,improving the GMI performance of magnetic cores remains challenging due to intrinsic limitations in material properties and structural stability.In this work,we explore the use of Joule heating to enhance the GMI response of Fe_(20)Ni_(80)/Cu composite wires.By applying a current of 1.8 A for 10 min,notable improvements in magnetic domain uniformity and a reduction in domain spacing are observed.Under these conditions,GMI ratios reach 1870% in the non-diagonal mode and1147%in the diagonal mode,respectively,highlighting their potential for applications in high-precision weak magnetic field sensing.展开更多
The fabrication of 304L stainless welding wires with a diameter 1.6 mm by using electrochemical cold drawing(ECD)of bars with a diameter of 5.6 mm was investigated,as well as that via traditional cold drawing(TCD)for ...The fabrication of 304L stainless welding wires with a diameter 1.6 mm by using electrochemical cold drawing(ECD)of bars with a diameter of 5.6 mm was investigated,as well as that via traditional cold drawing(TCD)for comparison.The results indicated that the dilute H_(2)SO_(4)aqueous solution was an appropriate electrolyte for ECD,and increasing the H_(2)SO_(4)concentration and current density within a range improved the corrosion rate and uniformity,leading to an easier and more coordinated deformation through uniformly distributing geometrically necessary dislocations and curved large-angle grain boundaries,and decreasing their density,and thus,an enhanced electrochemical plasticization(EP).Under the optimized electrochemical parameters(0.5 mol L^(-1)H_(2)SO_(4)electrolyte and current density of 12.2 mA cm^(-2)),the average cumulative reduction rate required for annealing was up to~34%,obviously higher than~20%of TCD due to the decreased work-hardening from the EP,so that the number of annealing was significantly reduced from 10 of TCD to 5,when the drawing pass was 23.In addition,the surface of the ECD wire was distinctly smoother and brighter than that of the TCD one.These findings confirm the large potential in engineering applications of the ECD technology based on the EP effect.展开更多
Inconel 625 alloy components were fabricated using hot wire laser metal deposition(HW-LMD)through process optimization,achieving a wire deposition rate of 1.72 kg/h.The microstructure and mechanical properties of the ...Inconel 625 alloy components were fabricated using hot wire laser metal deposition(HW-LMD)through process optimization,achieving a wire deposition rate of 1.72 kg/h.The microstructure and mechanical properties of the HW-LMD Inconel 625 alloys were systematically investigated.The results revealed that the microstructure of the HWLMD Inconel 625 alloys consisted of columnar dendrites,characterized by an average grain size of 12.5μm and a strong{100}〈001〉texture.The main phase identified wasγ-Ni,with the precipitation of Laves phase,measuring less than 1μm,observed in the inter-columnar dendritic regions.The average microhardness of the HW-LMD Inconel 625 alloys was HV1.0258.The yield strength and ultimate tensile strength were 493.5 and 837.4 MPa,respectively,with elongation exceeding 50%.Impact absorbing energies at 25 and-78℃were 223.08 and 200.24 J,respectively.Both the tensile and impact fracture surfaces exhibited dimples,indicating a ductile fracture mechanism during the deformation process.展开更多
Objective: To investigate the therapeutic advantages of closed reduction and Kirschner wire fixation versus open reduction and plate fixation in patients with hand surgery fractures. Methods: The sample was collected ...Objective: To investigate the therapeutic advantages of closed reduction and Kirschner wire fixation versus open reduction and plate fixation in patients with hand surgery fractures. Methods: The sample was collected from May 2021 to May 2025, consisting of 80 patients with hand surgery fractures. These patients were randomly divided into two groups using the red and blue ball method: the plate fixation group (40 cases, treated with open reduction and plate fixation) and the Kirschner wire fixation group (40 cases, treated with closed reduction and Kirschner wire fixation). The therapeutic effects between the two groups were randomly compared. Results: The Kirschner wire fixation group outperformed the plate fixation group in all indicators except for hand function scores (p < 0.05). There was no statistically significant difference in hand function scores between the two groups (p > 0.05). Conclusion: Compared with open reduction and plate fixation, closed reduction and Kirschner wire fixation for patients with hand surgery fractures achieves a more pronounced therapeutic effect, with advantages such as less trauma, shorter operation time, less bleeding, and a lower incidence of complications. It is suitable for hand surgery fractures with good stability. Open reduction and plate internal fixation have greater advantages in complex fractures and cases requiring high stability, and are worthy of promotion and application.展开更多
Unlike previous theories with velocity and/or elastic modulus averaging, we use a three-phase porous rock physics model developed by Santos for analyzing the seismic response of two immiscible fluids in saturated poro...Unlike previous theories with velocity and/or elastic modulus averaging, we use a three-phase porous rock physics model developed by Santos for analyzing the seismic response of two immiscible fluids in saturated porous media. Considering reservoir reference pressure and coupling drag of two fluids in pores, the effects of frequency, porosity, and gas saturation on the phase velocities of the P-and S-waves are discussed in detail under field conditions. The effects of porosity and gas saturation on Vp/Vs are also provided. The data for our numerical experiments are from a sample of deep volcanic rock from Daqing. The numerical results show that the frequency dispersion effect can be ignored for deep volcanic rocks with low porosity and low permeability. It is concluded that for deep volcanic rocks the effect of gas content in pores on Vp/Vs is negligible but the effect of porosity is significant when there is a certain amount of water contained in the pores. The accurate estimate of lithology and porosity in this case is relatively more important.展开更多
The three-phase bridge inverter is used as the converter topology in the power controller for a 9 kW doubly salient permanent magnet （DSPM） motor. Compared with common three-phase bridge inverters, the proposed inve...The three-phase bridge inverter is used as the converter topology in the power controller for a 9 kW doubly salient permanent magnet （DSPM） motor. Compared with common three-phase bridge inverters, the proposed inverter works under more complicated conditions with different principles for special winding back EMFs, position signals of hall sensors, and the given mode of switches. The ideal steady driving principles of the inverter for the motor are given. The working state with asymmetric winding back EMFs, inaccurate position signals of hall sensors, and the changing input voltage is analyzed. Finally, experimental results vertify that the given anal ysis is correct.展开更多
Generally, most soil slope failures are induced by rainfall infiltration, a process that involves interactions between the liquid phase, gas phase,and solid skeleton in an unsaturated soil slope. In this study, a loos...Generally, most soil slope failures are induced by rainfall infiltration, a process that involves interactions between the liquid phase, gas phase,and solid skeleton in an unsaturated soil slope. In this study, a loosely coupled liquid-gas-solid three-phase model, linking two numerical codes,TOUGH2/EOS3, which is used for water-air two-phase flow analysis, and FLAC^(3D), which is used for mechanical analysis, was established. The model was validated through a documented water drainage experiment over a sandy column and a comparison of the results with measured data and simulated results from other researchers. The proposed model was used to investigate the features of water-air two-phase flow and stress fields in an unsaturated soil slope during rainfall infiltration. The slope stability analysis was then performed based on the simulated water-air two-phase seepage and stress fields on a given slip surface. The results show that the safety factor for the given slip surface decreases first, then increases, and later decreases until the rainfall stops. Subsequently, a sudden rise occurs. After that, the safety factor decreases continually and reaches its lowest value, and then increases slowly to a steady value. The lowest value does not occur when the rainfall stops, indicating a delayed effect of the safety factor. The variations of the safety factor for the given slip surface are therefore caused by a combination of pore-air pressure, matric suction, normal stress, and net normal stress.展开更多
In the hydraulic transporting process of cutter-suction mining natural gas hydrate, when the temperature-pressure equilibrium of gas hydrate is broken, gas hydrates dissociate into gas. As a result, solid-liquid two-p...In the hydraulic transporting process of cutter-suction mining natural gas hydrate, when the temperature-pressure equilibrium of gas hydrate is broken, gas hydrates dissociate into gas. As a result, solid-liquid two-phase flow(hydrate and water) transforms into gas-solid-liquid three-phase flow(methane, hydrate and water) inside the pipeline. The Euler model and CFD-PBM model were used to simulate gas-solid-liquid three-phase flow. Numerical simulation results show that the gas and solid phase gradually accumulate to the center of the pipe. Flow velocity decreases from center to boundary of the pipe along the radial direction. Comparison of numerical simulation results of two models reveals that the flow state simulated by CFD-PBM model is more uniform than that simulated by Euler model, and the main behavior of the bubble is small bubbles coalescence to large one. Comparison of numerical simulation and experimental investigation shows that the values of flow velocity and gas fraction in CFD-PBM model agree with experimental data better than those in Euler model. The proposed PBM model provides a more accurate and effective way to estimate three-phase flow state of transporting gas hydrate within the submarine pipeline.展开更多
An innovative green process of producing ε-caprolactam was proposed by integrating ammoximation and Beckmann rearrangement effectively. As a first part of the new process, TS-1 molecular sieve-catalyzed synthesis of ...An innovative green process of producing ε-caprolactam was proposed by integrating ammoximation and Beckmann rearrangement effectively. As a first part of the new process, TS-1 molecular sieve-catalyzed synthesis of cyclohexanone oxime from cyclohexanone, ammonia and hydrogen peroxide was carried out in a batch plant. Cyclohexane was used as the solvent in the three-phase reaction system. The influences of essential process parameters on ammoximation were investigated. Under the reaction conditions as catalyst content of 2.5% (by mass); H 2 O 2 /yclohexanone molar ratio of 1.10; NH 3 /cyclohexanone molar ratio of 2.20; reaction temperature of 343 K; reaction time of 5 h, high conversion of cyclohexanone and selectivity to oxime (both>99%) were obtained. Thus, the three-phase ammoximation process showed equal catalytic activity as TS-1 but much more convenient and simpler for the separation of catalyst in comparison to the industrial two-phase system with t-butanol used as solvent.展开更多
基金supported by the National Natural Science Foundation of China(51977069)the National Natural Science Foundation Youth Project of China(52107195)the First Key Research and JieBang Headed Program,Hunan Province,China(2021GK1250).
文摘Switched-capacitor/flying capacitor(FC)based multilevel converters have been gaining higher attention for their voltage-boosting ability.This feature makes them an attractive solution for renewable energy systems,such as low-voltage input photovoltaic power systems and electric vehicle systems.However,they usually require more high voltage rating switches and flying capacitors along with boosting capability.Furthermore,they suffer from high pulse currents at the switching transients.Aiming to solve these issues,this article proposes a new self-balancing three-phase five-level inverter based on the switched-capacitor(5L-SCTPNPC),which reduces the dc voltage requirement.The number of active switches is relatively smaller and seven active switches are required per phase.Especially,a soft-charging circuit for FC is designed to limit the impulse charging current.Compared to conventional multilevel inverters,the proposed five-level inverter reduces dc bus voltage by 50%.Significantly,the voltage stress of FC and the switches in parallel with FC are all reduced by 50%in comparison with some existing similar boosting five-level active-neutral-point-clamped(5L-BANPC)inverters.The operating principles,modulation strategy,and the design of the FC and charging inductor are provided in detailly.A comprehensive comparison study has been made to highlight the merits of the proposed inverter.Finally,the simulations and experiments validate the feasibility of the proposed topology.
基金supported by the National Natural Science Foundation of China(No.22278439 and 21776313).
文摘Renewable electricity-driven production of value-added sulfur and H_(2)via electrocatalytic H_(2)S decomposition represents a sustainable route to conventional thermocatalysis.Both the electrocatalyst and electrolyte solution strongly impact the H_(2)S decomposition performance.Despite significant progress in developing sophisticated electrocatalysts,a well-designed electrolyte solution in conjunction with industrial catalysts is an attractive strategy to advance the industrialization process of electrocatalytic H_(2)S decomposition,but remains unexplored.Here,for the first time,we design a solid-liquid-gas three-phase indirect electrolysis system based on a kind of CS_(2)-N electrolyte solution and Ni-Mo_(2)C that can efficiently enable H_(2)S decomposition into valuable H_(2)and sulfur.Specifically,the solid-phase Ni-Mo_(2)C as a heterogeneous redox mediator presents excellent electrocatalytic efficiency for the H_(2)S removal efficiency of up to 99%,and the formation of liquid-phase sulfur product(CS_(2)-N electrolyte solution dissolves sulfur,yield up to 95%)with the generation of gas-phase H_(2)product(~1.32 mL min^(-1)),resulting in an interesting three-phase indirect electrolysis system.Remarkably,it enables the scale-up production(~6 g in a batch experiment)of sulfur with continuous operation for 120 h without attenuation.This work may inaugurate a new electrocatalytic H_(2)S decomposition avenue to explore porous metal materials and electrolyte systems in simultaneous production of value-added sulfur and H_(2).
基金supported by the National Natural Science Foundation of China(Nos.52422408 and 52171031)the Liaoning Xingliao Talents-Top-notch Young Talents Project(No.XLYC2203064)+1 种基金the Excellent Youth Fund of Liaoning Natural Science Foundation(No.2023JH3/10200001)the Fundamental Research Funds for the Central Universities(No.N2425004).
文摘The transient phenomena of re-oxidation and slag entrapment occurring in the tundish during the ladle change-over process have been proven detrimental to clean steel production.Therefore,an unsteady three-phase turbulence model,coupling velocity,temperature,and phase field was established to study the effect of the ladle shroud immersion depth on the slag eye formation,slag entrainment,slag dragging,air dragging,and flow characteristics during the ladle change-over process of a two-strand tundish.The results showed that reducing the immersion depth decreases the high-velocity region area under the slag layer in the quasi-steady process.During the emptying stage,as the molten bath level gradually decreases,the outlet temperature exhibits a trend of initially decreasing and subsequently increasing across all three shroud immersion depths.However,under a 210 mm shroud immersion depth,molten slag and air are dragged into the shroud,forming slag droplets and causing significant fluctuations,with a maximum scalar velocity of 0.0764 m/s at the monitoring point.In the filling stage,air and molten slag are dragged into the molten bath,forming bubbles and slag droplets at an immersion depth of 210 mm.Bubbles are observed within the molten slag layer,which can readily cause an emulsification phenomenon,making it easier to be dragged as slag droplets.Additionally,the slag eye area measured under 210 mm immersion depth at 45 s is 0.303 m^(2),while the maximum scalar velocity of 2.4259 m/s is detected at 12 s.At an immersion depth of 360 mm,the average area of the slag eye is minimized to 0.06268 m2,with corresponding variances of 0.006753,representing the optimal immersion depth.
文摘For three phase four-wire active power filters （APFs）, several typical power theories and corresponding current reference generation strategies are induced, p-q, d-q, unify power factor （UPF） and instantaneous active current （IAC） methods are analyzed and compared with each other. The interpretation of active and reactive currents in non-sinusoidal and unbalanced three-phase four-wire systems is given based on the generalized instantaneous reactive power theory. The performance and the characteristic are evaluated, and the application conditions of current reference generation strategies are concluded. Simulation results under different source voltages and loads verify the evaluation result.
基金supported in part by the National Natural Science Foundation of China under Grant 62303333in part by the Project of Hetao Shenzhen-Hong Kong Science and Technology Innovation Cooperation Zone under Grant HZQB-KCZYB-2020083.
文摘To achieve high power rating and low current harmonics of motor drive,this paper develops a dual three-phase open-winding permanent magnet synchronous motor(DTP-OW-PMSM)drive with the DC-link voltage ratio of 2:1:1.Based on this topology,this paper proposes a DTP four-level space vector pulse width modulation(DTP-FL SVPWM)strategy.First,two identical three-phase four-level space vector diagrams are constructed and divided.Then,three adjacent vectors nearest to the reference vector in each diagram are selected for the vector synthesis to guarantee high modulation precision and low switching frequency.Furthermore,to avoid the modulation error caused by the voltage deviation,the proposed DTP-FL SVPWM strategy is further optimized through unified duty ratio compensation(UDRC).The effectiveness of the proposed strategy is verified through experiments.
文摘The growing demand for efficient high-power switching power supplies has spurred interest in advanced topologies.The three-phase VIENNA converter stands out for its high power factor,simplified structure,and robust performance.Current research focuses on its operational principles,control strategies,and behavior under various load conditions.Key considerations include component selection,thermal management,and EMI/EMC optimization.This topology finds applications across renewable energy systems,industrial equipment,telecommunications,and electric vehicle charging infrastructures.Comparative analyses with alternative topologies and cost-benefit evaluations are also addressed.Future developments are expected to emphasize the integration of wide-bandgap devices and advancements in digital control techniques to further enhance efficiency and system performance.
基金National Key Research and Development Program of China(2022YFB4600902)Shandong Provincial Science Foundation for Outstanding Young Scholars(ZR2024YQ020)。
文摘Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.
基金supported by the National Key Research and Development Program of China under the grant of 2022YFB3403100。
文摘The dual three-phase PMSM(DTP-PMSM)drives have received wide attention at high-power high-efficiency applications due to their merits of high output current ability and copper-loss-free field excitation.Meanwhile,the DTPPMSM drive provides higher fault-tolerant capability for highreliability applications,e.g.,pumps and actuators in aircraft.For high-power drives with limited switching frequencies and highspeed drives with large fundamental frequencies,the ratio of switching frequency to fundamental frequency,i.e.,the carrier ratio,is usually below 15,which would significantly degrade the control performance.The purpose of this paper is to review the recent work on the modulation and control schemes for improving the operation performance of DTP-PMSM drives with low carrier ratios.Specifically,three categories of methods,i.e.,the space vector modulation based control,the model predictive control(MPC),and the optimized pulse pattern(OPP)based control are reviewed with principles and performance.In addition,brief discussions regarding the comparison and future trends are presented for low-carrier-ratio(LCR)modulation and control schemes of DTP-PMSM drives.
基金partially supported by the Center for Advanced Systems Understanding(CASUS)financed by Germany’s Federal Ministry of Education and Research(BMBF)+2 种基金the Saxon State Government out of the State Budget approved by the Saxon State Parliamentfunding from the European Union’s Just Transition Fund(JTF)within the project Röntgenlaser-Optimierung der Laserfusion(ROLF),Contract No.5086999001co-financed by the Saxon State Government out of the State Budget approved by the Saxon State Parliament.
文摘We present the first systematic experimental validation of return-current-driven cylindrical implosion scaling in micrometer-sized Cu and Al wires irradiated by J-class femtosecond laser pulses.Employing XFEL-based imaging with sub-micrometer spatial and femtosecond temporal resolution,supported by hydrodynamic and particle-in-cell simulations,we reveal how return current density depends precisely on wire diameter,material properties,and incident laser energy.We identify deviations from simple theoretical predictions due to geometrically influenced electron escape dynamics.These results refine and confirm the scaling laws essential for predictive modeling in high-energy-density physics and inertial fusion research.
基金Funded by Hunan Provincial Natural Science Foundation(No.2023JJ40074)Hunan Provincial Education Department Excellent Youth Project(No.21B0757)Hunan Provincial Engineering Technology Center(No.2022TP2036)。
文摘In this study,multilayer lamination welding was employed to prepare graphene/copper(Gr/Cu)composite billets from graphene-coated copper foils,followed by multi-pass cold drawing to produce Φ1 mm Gr/Cu composite wires.Microstructure and property analyses in both the cold-drawn and annealed states show that the incorporation of graphene significantly improves the ductility and electrical conductivity of the copper wire.After annealing at 350℃ for 30 minutes,the composite wire demonstrates a tensile strength of 270 MPa and an electrical conductivity of 102.74%IACS,both superior to those of pure copper wire under identical conditions.At 150℃,the electrical conductivity of the annealed composite wire reaches 72.60%IACS,notably higher than the 68.19%IACS of pure copper.The results suggest that graphene is uniformly distributed within the composite wire,with minimal impact on conductivity,while effectively refining the copper grain structure to enhance ductility.Moreover,graphene suppresses copper lattice vibrations at elevated temperatures,reducing the rate of conductivity degradation.
基金financially supported by the Key R&D Program of Shandong Province(2022SFGC0801)the National Natural Science Foundation of China(No.22005162 and 22175009)the Natural Science Foundation of Shandong Province(No.ZR2020QE093)。
文摘Osmotic energy,existing between the seawater and river water,is a renewable energy source,which can be directly converted into electricity by ion-exchange membranes(IEM).In traditional IEMs,the ion transport channels are formed by nanophase separation of hydrophilic ion carriers and hydrophobic segments.It is difficult to realize high-density ion channels with controlled spatial arrangement and length scale of ion carriers.Herein,we construct high-density 1D ion wires as transmission channels.Through molecular design,hydrophilic imidazole groups and hydrophobic alkyl tails were introduced into the repeat units,which self-assembled into 1D ion transporting core and protecting shell along the main chains.The areal density of the ionic wire arrays is up to~10^(12)cm^(-2),which is the highest value.The ionic wires ensure both high ion flux transport and high selectivity,achieving an ultrahigh-power density of 40.5 W m^(-2)at a 500-fold salinity gradient.Besides,the ionic wire array membrane is well recyclable and antibacterial.The ionic wires provide novel concept for next generation of high-performance membranes.
基金supported by the State Key Research and Development Program,Special Gravity Wave(Grant No.2023YFC2206003)the Gansu Provincial Science and Technology Program Funding(Grant No.24JRRA499)+1 种基金the Natural Science Foundation of Shandong Province(Grant No.ZR2024QB219)the Lanzhou City Science and Technology Program Project(Grant No.2025-2-47)。
文摘Giant magnetoimpedance(GMI)sensors are increasingly employed in modern magnetic sensing technologies.However,improving the GMI performance of magnetic cores remains challenging due to intrinsic limitations in material properties and structural stability.In this work,we explore the use of Joule heating to enhance the GMI response of Fe_(20)Ni_(80)/Cu composite wires.By applying a current of 1.8 A for 10 min,notable improvements in magnetic domain uniformity and a reduction in domain spacing are observed.Under these conditions,GMI ratios reach 1870% in the non-diagonal mode and1147%in the diagonal mode,respectively,highlighting their potential for applications in high-precision weak magnetic field sensing.
基金supported by Major Science and Technology Project of Gansu Province(Grant No.23ZDGA010)National Natural Science Foundation of China(Grant No.51971105).
文摘The fabrication of 304L stainless welding wires with a diameter 1.6 mm by using electrochemical cold drawing(ECD)of bars with a diameter of 5.6 mm was investigated,as well as that via traditional cold drawing(TCD)for comparison.The results indicated that the dilute H_(2)SO_(4)aqueous solution was an appropriate electrolyte for ECD,and increasing the H_(2)SO_(4)concentration and current density within a range improved the corrosion rate and uniformity,leading to an easier and more coordinated deformation through uniformly distributing geometrically necessary dislocations and curved large-angle grain boundaries,and decreasing their density,and thus,an enhanced electrochemical plasticization(EP).Under the optimized electrochemical parameters(0.5 mol L^(-1)H_(2)SO_(4)electrolyte and current density of 12.2 mA cm^(-2)),the average cumulative reduction rate required for annealing was up to~34%,obviously higher than~20%of TCD due to the decreased work-hardening from the EP,so that the number of annealing was significantly reduced from 10 of TCD to 5,when the drawing pass was 23.In addition,the surface of the ECD wire was distinctly smoother and brighter than that of the TCD one.These findings confirm the large potential in engineering applications of the ECD technology based on the EP effect.
基金supported by the Special Project of Gansu Province,China(Nos.23ZDGA010,22ZD6GA008)the Central Guiding Fund for Local Science and Technology Development Project,China(Nos.24ZYQA054,23ZYQA308)the Key Project of Research and Innovation in Universities,China(No.2024CXPT-06)。
文摘Inconel 625 alloy components were fabricated using hot wire laser metal deposition(HW-LMD)through process optimization,achieving a wire deposition rate of 1.72 kg/h.The microstructure and mechanical properties of the HW-LMD Inconel 625 alloys were systematically investigated.The results revealed that the microstructure of the HWLMD Inconel 625 alloys consisted of columnar dendrites,characterized by an average grain size of 12.5μm and a strong{100}〈001〉texture.The main phase identified wasγ-Ni,with the precipitation of Laves phase,measuring less than 1μm,observed in the inter-columnar dendritic regions.The average microhardness of the HW-LMD Inconel 625 alloys was HV1.0258.The yield strength and ultimate tensile strength were 493.5 and 837.4 MPa,respectively,with elongation exceeding 50%.Impact absorbing energies at 25 and-78℃were 223.08 and 200.24 J,respectively.Both the tensile and impact fracture surfaces exhibited dimples,indicating a ductile fracture mechanism during the deformation process.
文摘Objective: To investigate the therapeutic advantages of closed reduction and Kirschner wire fixation versus open reduction and plate fixation in patients with hand surgery fractures. Methods: The sample was collected from May 2021 to May 2025, consisting of 80 patients with hand surgery fractures. These patients were randomly divided into two groups using the red and blue ball method: the plate fixation group (40 cases, treated with open reduction and plate fixation) and the Kirschner wire fixation group (40 cases, treated with closed reduction and Kirschner wire fixation). The therapeutic effects between the two groups were randomly compared. Results: The Kirschner wire fixation group outperformed the plate fixation group in all indicators except for hand function scores (p < 0.05). There was no statistically significant difference in hand function scores between the two groups (p > 0.05). Conclusion: Compared with open reduction and plate fixation, closed reduction and Kirschner wire fixation for patients with hand surgery fractures achieves a more pronounced therapeutic effect, with advantages such as less trauma, shorter operation time, less bleeding, and a lower incidence of complications. It is suitable for hand surgery fractures with good stability. Open reduction and plate internal fixation have greater advantages in complex fractures and cases requiring high stability, and are worthy of promotion and application.
文摘Unlike previous theories with velocity and/or elastic modulus averaging, we use a three-phase porous rock physics model developed by Santos for analyzing the seismic response of two immiscible fluids in saturated porous media. Considering reservoir reference pressure and coupling drag of two fluids in pores, the effects of frequency, porosity, and gas saturation on the phase velocities of the P-and S-waves are discussed in detail under field conditions. The effects of porosity and gas saturation on Vp/Vs are also provided. The data for our numerical experiments are from a sample of deep volcanic rock from Daqing. The numerical results show that the frequency dispersion effect can be ignored for deep volcanic rocks with low porosity and low permeability. It is concluded that for deep volcanic rocks the effect of gas content in pores on Vp/Vs is negligible but the effect of porosity is significant when there is a certain amount of water contained in the pores. The accurate estimate of lithology and porosity in this case is relatively more important.
文摘The three-phase bridge inverter is used as the converter topology in the power controller for a 9 kW doubly salient permanent magnet （DSPM） motor. Compared with common three-phase bridge inverters, the proposed inverter works under more complicated conditions with different principles for special winding back EMFs, position signals of hall sensors, and the given mode of switches. The ideal steady driving principles of the inverter for the motor are given. The working state with asymmetric winding back EMFs, inaccurate position signals of hall sensors, and the changing input voltage is analyzed. Finally, experimental results vertify that the given anal ysis is correct.
基金supported by the National Natural Science Foundation of China(Grants No.51579170 and 51179118)the Science Fund for Creative Research Groups of the National Natural Science Foundation of China(Grant No.51321065)
文摘Generally, most soil slope failures are induced by rainfall infiltration, a process that involves interactions between the liquid phase, gas phase,and solid skeleton in an unsaturated soil slope. In this study, a loosely coupled liquid-gas-solid three-phase model, linking two numerical codes,TOUGH2/EOS3, which is used for water-air two-phase flow analysis, and FLAC^(3D), which is used for mechanical analysis, was established. The model was validated through a documented water drainage experiment over a sandy column and a comparison of the results with measured data and simulated results from other researchers. The proposed model was used to investigate the features of water-air two-phase flow and stress fields in an unsaturated soil slope during rainfall infiltration. The slope stability analysis was then performed based on the simulated water-air two-phase seepage and stress fields on a given slip surface. The results show that the safety factor for the given slip surface decreases first, then increases, and later decreases until the rainfall stops. Subsequently, a sudden rise occurs. After that, the safety factor decreases continually and reaches its lowest value, and then increases slowly to a steady value. The lowest value does not occur when the rainfall stops, indicating a delayed effect of the safety factor. The variations of the safety factor for the given slip surface are therefore caused by a combination of pore-air pressure, matric suction, normal stress, and net normal stress.
基金Project(51375498) supported by the National Natural Science Foundation of China
文摘In the hydraulic transporting process of cutter-suction mining natural gas hydrate, when the temperature-pressure equilibrium of gas hydrate is broken, gas hydrates dissociate into gas. As a result, solid-liquid two-phase flow(hydrate and water) transforms into gas-solid-liquid three-phase flow(methane, hydrate and water) inside the pipeline. The Euler model and CFD-PBM model were used to simulate gas-solid-liquid three-phase flow. Numerical simulation results show that the gas and solid phase gradually accumulate to the center of the pipe. Flow velocity decreases from center to boundary of the pipe along the radial direction. Comparison of numerical simulation results of two models reveals that the flow state simulated by CFD-PBM model is more uniform than that simulated by Euler model, and the main behavior of the bubble is small bubbles coalescence to large one. Comparison of numerical simulation and experimental investigation shows that the values of flow velocity and gas fraction in CFD-PBM model agree with experimental data better than those in Euler model. The proposed PBM model provides a more accurate and effective way to estimate three-phase flow state of transporting gas hydrate within the submarine pipeline.
基金Supported by the National Natural Science Foundation of China and Sinopec (20736009)
文摘An innovative green process of producing ε-caprolactam was proposed by integrating ammoximation and Beckmann rearrangement effectively. As a first part of the new process, TS-1 molecular sieve-catalyzed synthesis of cyclohexanone oxime from cyclohexanone, ammonia and hydrogen peroxide was carried out in a batch plant. Cyclohexane was used as the solvent in the three-phase reaction system. The influences of essential process parameters on ammoximation were investigated. Under the reaction conditions as catalyst content of 2.5% (by mass); H 2 O 2 /yclohexanone molar ratio of 1.10; NH 3 /cyclohexanone molar ratio of 2.20; reaction temperature of 343 K; reaction time of 5 h, high conversion of cyclohexanone and selectivity to oxime (both>99%) were obtained. Thus, the three-phase ammoximation process showed equal catalytic activity as TS-1 but much more convenient and simpler for the separation of catalyst in comparison to the industrial two-phase system with t-butanol used as solvent.
