A three-phase reactor mathematical model was set up to simulate and design a three-phase bubble column reactor for direct synthesis of dimethyl ether （DME） from syngas, considering both the influence of part inert c...A three-phase reactor mathematical model was set up to simulate and design a three-phase bubble column reactor for direct synthesis of dimethyl ether （DME） from syngas, considering both the influence of part inert carrier backmixing on transfer and the influence of catalyst grain sedimentation on reaction. On the basis of this model, the influences of the size and reaction conditions of a 100000 t/a DME reactor on capacity were investigated. The optimized size of the 10000 t/a DME synthesis reactor was proposed as follows： diameter 3.2 m, height 20 m, built-in 400 tube heat exchanger （Ф 38×2 mm）, and inert heat carrier paraffin oil 68 t and catalyst 34.46 t. Reaction temperature and pressure were important factors influencing the reaction conversion for different size reactors. Under the condition of uniform catalyst concentration distribution, higher pressure and temperature were proposed to achieve a higher production capacity of DME. The best ratio of fresh syngas for DME synthesis was 2.04.展开更多
Based on the conductance fluctuation signals measured from vertical upward oil-gas-water three-phase flow experiment, time frequency representation and surrogate data method were used to investigate dynamical characte...Based on the conductance fluctuation signals measured from vertical upward oil-gas-water three-phase flow experiment, time frequency representation and surrogate data method were used to investigate dynamical characteristics of oil-in-water type bubble and slug flows. The results indicate that oil-in-water type bubble flow will turn to deterministic motion with the increase of oil phase fraction f o and superficial gas velocity U sg under fixed flowrate of oil-water mixture Q mix . The dynamics of oil-in-water type slug flow becomes more complex with the increase of U sg under fixed flowrate of oil-water mixture. The change of f o leads to irregular influence on the dynamics of slug flow. These interesting findings suggest that the surrogate data method can be a faithful tool for characterizing dynamic characteristics of oil-in-water type bubble and slug flows.展开更多
Features of the motion of gel particles in a three-phase bubble column with non-foaming and foaming gas–liquid systems,determined by using experiments of radioactive particle tracking(RPT),have been compared.The trac...Features of the motion of gel particles in a three-phase bubble column with non-foaming and foaming gas–liquid systems,determined by using experiments of radioactive particle tracking(RPT),have been compared.The tracer used is a gel particle which resembles typical immobilized biocatalyst.The tracer trajectory is analyzed to extract relevant information for design purposes.The solid velocity field,turbulence parameters,dispersion coefficients,mixing times and flow transitions are determined and compared.The presence of foam significantly affects many quantified parameters,especially within the heterogeneous flow regime.The hydrodynamic stresses are reduced in the presence of foam,especially close to the disengagement.The dispersion coefficients also decrease,and the solid mixing time is only slightly affected by the presence of foam.Gas holdup,inferred both from RPT experiments and from gamma ray scanning,is higher for foaming systems and leads to a shift in the transition gas velocity towards higher values.展开更多
In this study,the dynamic characteristics of microscale floating bubbles near the vertical wall are studied.This occurrence is common in industrial and natural phenomena.Although many studies have been conducted on mi...In this study,the dynamic characteristics of microscale floating bubbles near the vertical wall are studied.This occurrence is common in industrial and natural phenomena.Although many studies have been conducted on microscale bubbles,few studies investigate floating bubbles with very small Reynolds number(Re)near the wall,which is the main research goal of this study.Therefore,this study establishes a model for the ascent of small-scale bubbles near a vertical wall using the interFoam solver in OpenFOAM.This study investigates the influences of diverse viscosity parameters,varying distances from the wall,and different gas flow rates on the terminal velocity,deformation,and motion trajectory of bubbles.The results reveal that as liquid viscosity increases,the Re of bubbles gradually decreases and reaches a minimum of 0.012,which is similar to the Re of micrometer-sized bubbles in water.The characteristics of the wall-induced force in the longitudinal direction are closely related to the changes in liquid viscosity.Under low-viscosity conditions,the induced lift is the principal form of action,whereas under high-viscosity conditions,it is primarily manifested as induced drag.展开更多
This paper examines a model that combines vortex generators and leading-edge tubercles for controlling the laminar separation bubble(LSB)over an airfoil at low Reynolds numbers(Re).This new concept of passive flow con...This paper examines a model that combines vortex generators and leading-edge tubercles for controlling the laminar separation bubble(LSB)over an airfoil at low Reynolds numbers(Re).This new concept of passive flow control technique utilizing a tubercle and vortex generator(VG)close to the leading edge was analyzed numerically for a NACA0015 airfoil.In this study,the Shear Stress Transport(SST)turbulence model was employed in the numerical modelling.Numerical modelling was completed using the ANSYS-Fluent 18.2 solver.Analyses were conducted to investigate the flow pattern and understand the underlying LSB control phenomena that enabled the new passive flow control method to provide this significant performance benefit.The findings indicated that the new concept of passive flow control technique suppressed the formation of an LSB at the suction surface of the NACA0015 airfoil,resulting in a higher lift coefficient and improved aerodynamic performance.Improvements in LSB dynamics and aerodynamic performance through the passive flow control method lead to increased energy output and enhanced stability.展开更多
The transient phenomena of re-oxidation and slag entrapment occurring in the tundish during the ladle change-over process have been proven detrimental to clean steel production.Therefore,an unsteady three-phase turbul...The transient phenomena of re-oxidation and slag entrapment occurring in the tundish during the ladle change-over process have been proven detrimental to clean steel production.Therefore,an unsteady three-phase turbulence model,coupling velocity,temperature,and phase field was established to study the effect of the ladle shroud immersion depth on the slag eye formation,slag entrainment,slag dragging,air dragging,and flow characteristics during the ladle change-over process of a two-strand tundish.The results showed that reducing the immersion depth decreases the high-velocity region area under the slag layer in the quasi-steady process.During the emptying stage,as the molten bath level gradually decreases,the outlet temperature exhibits a trend of initially decreasing and subsequently increasing across all three shroud immersion depths.However,under a 210 mm shroud immersion depth,molten slag and air are dragged into the shroud,forming slag droplets and causing significant fluctuations,with a maximum scalar velocity of 0.0764 m/s at the monitoring point.In the filling stage,air and molten slag are dragged into the molten bath,forming bubbles and slag droplets at an immersion depth of 210 mm.Bubbles are observed within the molten slag layer,which can readily cause an emulsification phenomenon,making it easier to be dragged as slag droplets.Additionally,the slag eye area measured under 210 mm immersion depth at 45 s is 0.303 m^(2),while the maximum scalar velocity of 2.4259 m/s is detected at 12 s.At an immersion depth of 360 mm,the average area of the slag eye is minimized to 0.06268 m2,with corresponding variances of 0.006753,representing the optimal immersion depth.展开更多
Understanding the bubble behaviours and flow characteristics of large-capacity bottom-blowing electric arc furnace(EAF)is crucial for potential exogenous gas-induced slag foaming process and enhancement of molten bath...Understanding the bubble behaviours and flow characteristics of large-capacity bottom-blowing electric arc furnace(EAF)is crucial for potential exogenous gas-induced slag foaming process and enhancement of molten bath dynamics.A physical model and a 3D gas-slag-steel transient bottom-blowing numerical model of a 150 t EAF were established to investigate the bubble behaviour and flow characteristics throughout the molten steel bath and slag layer under bottom-blowing,with referring to gas flow rate,plug diameter,plug arrangement and injection angle.Results indicate that the average bubble sizes experience increase,dynamic stability and decrease in molten steel bath and then undergo decrease and increase after entering into slag layer for all bottom-blowing modes.The bubble numbers exhibit the opposing trends during the process.Increase in gas flow rate leads to a significant rise in average bubble size but a decrease in number,average dwelling time and the spread area of bubbles in slag layer.Increase in plug diameter causes an opposite impact.The effect of plug arrangement radii on bubbles is almost negligible.Increasing the injection angle results in an increase in bubble size and a decrease in both bubble number and dwelling time in slag layer.The slag foaming potential was discussed referring to the bubble size,number and dwelling time in slag layer.Increase in gas flow rate and plug diameters can significantly enhance the fluids flow through increasing average flow velocity,decreasing mixing time and dead zone ratio of molten bath.Plug arrangement radius and injection angle express nonlinear correlation with average flow velocity and dead zone ratio,and the plug arrangement radius of 0.5R(R represents the radius of bottom circle of EAF model)and injection angle of 15°perform better in enhancing dynamics of molten bath.A group of bottom-blowing parameters are proposed to achieve better comprehensive performance of bubble-induced slag foaming and molten bath dynamics.展开更多
Legged robots have considerable potential for traversing unstructured situations;nonetheless,their inflexible frameworks often constrain adaptability and obstacle negotiation.The study article presents a revolutionary...Legged robots have considerable potential for traversing unstructured situations;nonetheless,their inflexible frameworks often constrain adaptability and obstacle negotiation.The study article presents a revolutionary Soft Tri-Legged Robot(STLR)that improves movement and obstacle-avoidance skills by using a bio-inspired pneumatic artificial muscle(Bubble Artificial Muscles)and a bio-inspired tactile sensor(TacTip).The STLR is activated by BAMs,which are flexible,pneu-matic-driven actuators that provide fine control over forward,backward,and steering movements.Obstacle identification and avoidance are facilitated by the TacTip sensor,which delivers tactile input for traversing unstructured terrains.We delineate the mechanical features of the BAMs,assess the functionality of the robot's legs,and elaborate on the incorpora-tion of the tactile sensing system.Experimental results demonstrate that the STLR can effectively achieve multi-directional flexible movement and obstacle avoidance through a cross-modal perception-actuation mechanism.This study highlights the promise of soft robotics for search and rescue,medical aid,and autonomous exploration,while delineating difficulties and opportunities for future improvements in functionality and efficiency.展开更多
350 keV He^(+) ions were injected into laser powder bed fusion(LPBF)-processed 304L stainless steel and traditional rolled 304L stainless steel with a flux of 1×10^(17) ions/cm^(2) at room temperature,followed by...350 keV He^(+) ions were injected into laser powder bed fusion(LPBF)-processed 304L stainless steel and traditional rolled 304L stainless steel with a flux of 1×10^(17) ions/cm^(2) at room temperature,followed by annealing at 750℃ for 10,100,and 300 h,respectively.The results showed that material swelling due to helium bubble coarsening was almost not observed in either the LPBF or rolled samples after 10 h of annealing duration.Rapid coarsening and swelling of bubbles occurred in the rolled samples,but only moderate bubble growth occurred in the LPBF sample after annealing for 100 h.After annealing for 300 h,the helium bubbles in both samples tended to grow steadily.For 10 h of annealing,the irradiated samples were in a disequilibrium state,and the apparent activation energy(E^(act))calculated by the Arrhenius model determined that helium atoms tended to diffuse through the displacement mechanism,and helium bubbles grew under the migration and coalescence(MC)mechanism.With annealing times over 100 h,the high-density dislocations and nano-oxide particles in the LPBF sample still had a strong trapping effect on the movement and growth of helium bubbles.After annealing for 300 h,the cellular subgrains in the LPBF sample decomposed,and the nano-oxide particles had no trapping effect on the helium bubbles.At this time,the dislocation structure played a primary role in suppressing the growth of helium bubbles,and the radiation resistance of the LPBF sample remained superior to that of the rolled samples.展开更多
The current technical standards primarily relied on experience to judge the interfacial bonding properties between the self-compacting concrete filling layer and the steam-cured concrete precast slab in CRTS Ⅲ slab b...The current technical standards primarily relied on experience to judge the interfacial bonding properties between the self-compacting concrete filling layer and the steam-cured concrete precast slab in CRTS Ⅲ slab ballastless track structure.This study sought to enhance technical standards for evaluating interfacial bonding properties by suggesting the use of the splitting tensile strength to evaluate the impact of bubble defects.Specimens were fabricated through on-site experiment.The percent of each area of 6 cm^(2)or more bubble defect was 0 in most of specimens.When the cumulative area of all bub-ble defects reached 12%,the splitting tensile strength value was 0.67 MPa,which exceeded the minimum required value of 0.5 MPa for ensuring bonding interface adhesion.Furthermore,when the cumulative area of all bubble defects reached 8%,the splitting tensile strength value was 0.85 MPa,which exceeded the minimum required value of 0.8 MPa,thereby over-coming the negative impact of each area of 10 cm^(2) or more bubble defect.Additionally,keeping the cumulative area of each area of 6 cm^(2) or more bubble defect below 6%ensured adequate bonding strength and reduced the occurrence of specimens with lower splitting tensile strength values.展开更多
The damage evolution of polycrystalline Al with helium(He)bubbles under strongly decaying shock waves is studied by molecular dynamics simulations.A new damage region is observed near the loading side of the sample,an...The damage evolution of polycrystalline Al with helium(He)bubbles under strongly decaying shock waves is studied by molecular dynamics simulations.A new damage region is observed near the loading side of the sample,and the evolution characteristics and underlying mechanisms are elucidated.The development of damage in the new damage region begins after complete unloading of the incident shock wave and is further enhanced when the tensile stress arrives later.The damage evolution is completely controlled by the expansion-merging of He bubbles,without nucleation–growth of voids.This new damage region can be divided into two sections,each of which exhibits a unique dominant mechanism.The damage in the section closer to the loading side is due to the reverse velocity gradient formed after complete unloading of the incident shock wave,depending on the rate of decrease and the amplitude of the initial peak pressure.A high initial peak pressure that can lead to melting of material near the loading side is a necessary condition for the formation of the new damage region,since a significant reverse velocity gradient can only be established if melting occurs.The dominant mechanism in the section distant from the loading side is the action of tensile stress,associated with the profile of the incident shock wave upon reaching the free surface,which determines the material phase near the free surface.Moreover,the presence of He bubbles is another critical factor for formation of the new damage region,which does not occur in pure Al samples.展开更多
Local hydrodynamics of a gas–liquid–solid system,such as bubble circulation regime,gas holdup,liquid velocity and axial profile of solid concentration,are studied in a two-stage internal loop airlift reactor.Empiric...Local hydrodynamics of a gas–liquid–solid system,such as bubble circulation regime,gas holdup,liquid velocity and axial profile of solid concentration,are studied in a two-stage internal loop airlift reactor.Empirical correlations for gas holdup and liquid velocity are proposed to ease the reactor design and scale-up.Different bubble circulation regimes were displayed in the first(lower) and second(upper) stages.Increasing superficial gas velocity and solid loading can promote regime transition of the second stage,and the gas holdup of the second stage is higher than that of the lower stage.In addition,the effects of solid loading on bubble behaviour are experimentally investigated for each stage.It is found that bubble size in the downcomer decreases with the presence of solid particles,and bubble size distribution widens under higher superficial gas velocity and lower solid loading.展开更多
A special experiment setup was designed to observe the interaction between bubbles and particle in flotation cell and to analyze the bubble characteristics such as bubble size, distribution and bubble-loading efficien...A special experiment setup was designed to observe the interaction between bubbles and particle in flotation cell and to analyze the bubble characteristics such as bubble size, distribution and bubble-loading efficiency. Bubbles in water-gas system and three-phase system were measured. The results indicate that with the current setup the bubbles as small as 10 μm can be easily distinguished. The average size of the bubbles generated under the given conditions in two-phase system is 410 μm at frother concentration of 0.004%, which is in good correspondence with the results of other works. The effect of frother on bubble size was probed. Increasing frother concentration from 0 to 0.004% causes a reduction of bubble size from 700 to 400 μm. The bubble loading efficiency was reported. The result indicates that the fine particle is more easily entrapped than the coarse particle. Some factors, which have effect on measurement accuracy were discussed. The aeration speed has a significant effect on the accuracy of results, if it surpasses 30 mL/s, and the image becomes unclear due to the entrapment of fine particle. Another factor, which can affect observing results, is the sampling position. At a wrong sampling position, the images become unclear.展开更多
In this paper,the failure caused by HRAM loads which were generated by high-speed projectile penetration,and protection technology of the fluid-filled structure were explored.A bubble was preset on the projectile traj...In this paper,the failure caused by HRAM loads which were generated by high-speed projectile penetration,and protection technology of the fluid-filled structure were explored.A bubble was preset on the projectile trajectory in a fluid-filled structure.Based on the reflection and transmission phenomena of pressure waves at the gas-liquid interface and the compressibility characteristics of gases,a numerical analysis was conducted on the influence of preset bubble on projectile penetration and structural failure characteristics.The results indicate that the secondary water-entry impact phenomenon occurs when a preset bubble exists on the projectile trajectory,leading to the secondary water entry impact loads.The rarefaction waves reflected on the surface of the preset bubble cause the attenuation ratio of the initial impact pressure peak to reach 68.8%and the total specific impulse attenuation ratio to reach 48.6%.Furthermore,the larger the bubble,the faster the projectile,and the more obvious the attenuation effect.Moreover,due to the compressibility of the bubble,the global deformation attenuation ratio of the front and rear walls can reach over 80%.However,the larger the bubble size,the faster the projectile velocity,the smaller the local deformation attenuation effect of the rear wall,and the more severe the failure at the perforation of the rear wall.展开更多
This paper highlights the crucial role of Indonesia’s GNSS receiver network in advancing Equatorial Plasma Bubble(EPB)studies in Southeast and East Asia,as ionospheric irregularities within EPB can disrupt GNSS signa...This paper highlights the crucial role of Indonesia’s GNSS receiver network in advancing Equatorial Plasma Bubble(EPB)studies in Southeast and East Asia,as ionospheric irregularities within EPB can disrupt GNSS signals and degrade positioning accuracy.Managed by the Indonesian Geospatial Information Agency(BIG),the Indonesia Continuously Operating Reference Station(Ina-CORS)network comprises over 300 GNSS receivers spanning equatorial to southern low-latitude regions.Ina-CORS is uniquely situated to monitor EPB generation,zonal drift,and dissipation across Southeast Asia.We provide a practical tool for EPB research,by sharing two-dimensional rate of Total Electron Content(TEC)change index(ROTI)derived from this network.We generate ROTI maps with a 10-minute resolution,and samples from May 2024 are publicly available for further scientific research.Two preliminary findings from the ROTI maps of Ina-CORS are noteworthy.First,the Ina-CORS ROTI maps reveal that the irregularities within a broader EPB structure persist longer,increasing the potential for these irregularities to migrate farther eastward.Second,we demonstrate that combined ROTI maps from Ina-CORS and GNSS receivers in East Asia and Australia can be used to monitor the development of ionospheric irregularities in Southeast and East Asia.We have demonstrated the combined ROTI maps to capture the development of ionospheric irregularities in the Southeast/East Asian sector during the G5 Geomagnetic Storm on May 11,2024.We observed simultaneous ionospheric irregularities in Japan and Australia,respectively propagating northwestward and southwestward,before midnight,whereas Southeast Asia’s equatorial and low-latitude regions exhibited irregularities post-midnight.By sharing ROTI maps from Indonesia and integrating them with regional GNSS networks,researchers can conduct comprehensive EPB studies,enhancing the understanding of EPB behavior across Southeast and East Asia and contributing significantly to ionospheric research.展开更多
In recent years,the phenomenon of multistability has attracted wide attention.In this paper,a memristive chaotic system with extreme multistability is constructed by using a memristor.The dynamic behavior of the syste...In recent years,the phenomenon of multistability has attracted wide attention.In this paper,a memristive chaotic system with extreme multistability is constructed by using a memristor.The dynamic behavior of the system is analyzed by Poincar´e mapping,a time series diagram,and a bifurcation diagram.The results show that the new system has several significant characteristics.First,the new system has a constant Lyapunov exponent,transient chaos and one complete Feigenbaum tree.Second,the system has the phenomenon of bifurcation map shifts that depend on the initial conditions.In addition,we find periodic bursting oscillations,chaotic bursting oscillations,and the transition of chaotic bursting oscillations to periodic bursting oscillations.In particular,when the system parameters take different discrete values,the system generates a bubble phenomenon that varies with the initial conditions,and this bubble can be shifted with the initial values,which has rarely been seen in the previous literature.The implementation by field-programmable gate array(FPGA)and analog circuit simulation show close alignment with the MATLAB numerical simulation results,validating the system’s realizability.Additionally,the image encryption algorithm integrating DNA-based encoding and chaotic systems further demonstrates its practical applicability.展开更多
Bubbles play crucial roles in various fields,including naval and ocean engineering,chemical engineering,and biochemical engineering.Numerous theoretical analyses,numerical simulations,and experimental studies have bee...Bubbles play crucial roles in various fields,including naval and ocean engineering,chemical engineering,and biochemical engineering.Numerous theoretical analyses,numerical simulations,and experimental studies have been conducted to reveal the mysteries of bubble motion and its mechanisms.These efforts have significantly advanced research in bubble dynamics,where theoretical study is an efficient method for bubble motion prediction.Since Lord Rayleigh introduced the theoretical model of single-bubble motion in incompressible fluid in 1917,theoretical studies have been pivotal in understanding bubble dynamics.This study provides a comprehensive review of the development and applicability of theoretical studies in bubble dynamics using typical theoretical bubble models across different periods as a focal point and an overview of bubble theory applications in underwater explosion,marine cavitation,and seismic exploration.This study aims to serve as a reference and catalyst for further advancements in theoretical analysis and practical applications of bubble theory across marine fields.展开更多
Unlike conventional spherical charges,a shaped charge generates not only a strong shock wave and a pulsating bubble,but also a high strain rate metal jet and a ballistic wave during the underwater explosion.They show ...Unlike conventional spherical charges,a shaped charge generates not only a strong shock wave and a pulsating bubble,but also a high strain rate metal jet and a ballistic wave during the underwater explosion.They show significant characteristic differences and couple each other.This paper designs and conducts experiments with shaped charges to analyze the complicated process.The effects of liner angle and weight of shaped charge on the characteristics of metal jets,waves,and bubbles are discussed.It is found that in underwater explosions,the shaped charge generates the metal jet accompanied by the ballistic wave.Then,the shock wave propagates and superimposes with the ballistic wave,and the generated bubble pulsates periodically.It is revealed that the maximum head velocity of the metal jet versus the liner angle a and length-to-diameter ratio k of the shaped charge follows the laws of 1/(α/180°)^(0.55)andλ^(0.16),respectively.The head shape and velocity of the metal jet determine the curvature and propagation speed of the initial ballistic wave,thus impacting the superposition time and region with the shock wave.Our findings also reveal that the metal jet carries away some explosion products,which hinders the bubble development,causing an inward depression of the bubble wall near the metal jet.Therefore,the maximum bubble radius and pulsation period are 5.2%and 3.9%smaller than the spherical charge with the same weight.In addition,the uneven axial energy distribution of the shaped charge leads to an oblique bubble jet formation.展开更多
To analyze the impact of bubbles on the mechanical behavior of glasses,by controlling the refining time,we prepared three borosilicate glasses with the same composition and different porosity.By the analysis software ...To analyze the impact of bubbles on the mechanical behavior of glasses,by controlling the refining time,we prepared three borosilicate glasses with the same composition and different porosity.By the analysis software integrated within the optical microscope,the diameter and number of the bubbles on the surface of three borosilicate glasses were quantified.From the hardness and crack initiation resistance(CR),we built the relationship between the porosity and the mechanical performance of these borosilicate glasses.展开更多
基金This work was supported by the National Basic Research Program of China (2005CB221205)
文摘A three-phase reactor mathematical model was set up to simulate and design a three-phase bubble column reactor for direct synthesis of dimethyl ether （DME） from syngas, considering both the influence of part inert carrier backmixing on transfer and the influence of catalyst grain sedimentation on reaction. On the basis of this model, the influences of the size and reaction conditions of a 100000 t/a DME reactor on capacity were investigated. The optimized size of the 10000 t/a DME synthesis reactor was proposed as follows： diameter 3.2 m, height 20 m, built-in 400 tube heat exchanger （Ф 38×2 mm）, and inert heat carrier paraffin oil 68 t and catalyst 34.46 t. Reaction temperature and pressure were important factors influencing the reaction conversion for different size reactors. Under the condition of uniform catalyst concentration distribution, higher pressure and temperature were proposed to achieve a higher production capacity of DME. The best ratio of fresh syngas for DME synthesis was 2.04.
基金Supported by the National Natural Science Foundation of China (50974095, 41174109)Gao Zhongke (高忠科) was also supported by the National Natural Science Foundation of China (61104148)+2 种基金the National Science and Technology Major Projects (2011ZX05020-006)Specialized Research Fund for the Doctoral Program of Higher Education of China(20110032120088)the Independent Innovation Foundation of Tianjin University
文摘Based on the conductance fluctuation signals measured from vertical upward oil-gas-water three-phase flow experiment, time frequency representation and surrogate data method were used to investigate dynamical characteristics of oil-in-water type bubble and slug flows. The results indicate that oil-in-water type bubble flow will turn to deterministic motion with the increase of oil phase fraction f o and superficial gas velocity U sg under fixed flowrate of oil-water mixture Q mix . The dynamics of oil-in-water type slug flow becomes more complex with the increase of U sg under fixed flowrate of oil-water mixture. The change of f o leads to irregular influence on the dynamics of slug flow. These interesting findings suggest that the surrogate data method can be a faithful tool for characterizing dynamic characteristics of oil-in-water type bubble and slug flows.
基金Supported by the FONCyT(PICT2014-0704)CONICET(PIP1122015-0100902CO)Universidad de Buenos Aires(UBACyT 20020130100544BA)
文摘Features of the motion of gel particles in a three-phase bubble column with non-foaming and foaming gas–liquid systems,determined by using experiments of radioactive particle tracking(RPT),have been compared.The tracer used is a gel particle which resembles typical immobilized biocatalyst.The tracer trajectory is analyzed to extract relevant information for design purposes.The solid velocity field,turbulence parameters,dispersion coefficients,mixing times and flow transitions are determined and compared.The presence of foam significantly affects many quantified parameters,especially within the heterogeneous flow regime.The hydrodynamic stresses are reduced in the presence of foam,especially close to the disengagement.The dispersion coefficients also decrease,and the solid mixing time is only slightly affected by the presence of foam.Gas holdup,inferred both from RPT experiments and from gamma ray scanning,is higher for foaming systems and leads to a shift in the transition gas velocity towards higher values.
基金Supported by the National Natural Science Foundation of China(Grant No.52271319)the Jiangsu Funding Program for Excellent Postdoctoral Talent,and the Postdoctoral Fellowship Program of China Postdoctoral Science Foundation(Grant No.GZC20240618)the Natural Science Foundation of Jiangsu Province of China(BK20231525).
文摘In this study,the dynamic characteristics of microscale floating bubbles near the vertical wall are studied.This occurrence is common in industrial and natural phenomena.Although many studies have been conducted on microscale bubbles,few studies investigate floating bubbles with very small Reynolds number(Re)near the wall,which is the main research goal of this study.Therefore,this study establishes a model for the ascent of small-scale bubbles near a vertical wall using the interFoam solver in OpenFOAM.This study investigates the influences of diverse viscosity parameters,varying distances from the wall,and different gas flow rates on the terminal velocity,deformation,and motion trajectory of bubbles.The results reveal that as liquid viscosity increases,the Re of bubbles gradually decreases and reaches a minimum of 0.012,which is similar to the Re of micrometer-sized bubbles in water.The characteristics of the wall-induced force in the longitudinal direction are closely related to the changes in liquid viscosity.Under low-viscosity conditions,the induced lift is the principal form of action,whereas under high-viscosity conditions,it is primarily manifested as induced drag.
基金the Scientific Research Projects Unit of Erciyes University under contract no:FDS-2022-11532 and FOA-2025-14773.
文摘This paper examines a model that combines vortex generators and leading-edge tubercles for controlling the laminar separation bubble(LSB)over an airfoil at low Reynolds numbers(Re).This new concept of passive flow control technique utilizing a tubercle and vortex generator(VG)close to the leading edge was analyzed numerically for a NACA0015 airfoil.In this study,the Shear Stress Transport(SST)turbulence model was employed in the numerical modelling.Numerical modelling was completed using the ANSYS-Fluent 18.2 solver.Analyses were conducted to investigate the flow pattern and understand the underlying LSB control phenomena that enabled the new passive flow control method to provide this significant performance benefit.The findings indicated that the new concept of passive flow control technique suppressed the formation of an LSB at the suction surface of the NACA0015 airfoil,resulting in a higher lift coefficient and improved aerodynamic performance.Improvements in LSB dynamics and aerodynamic performance through the passive flow control method lead to increased energy output and enhanced stability.
基金supported by the National Natural Science Foundation of China(Nos.52422408 and 52171031)the Liaoning Xingliao Talents-Top-notch Young Talents Project(No.XLYC2203064)+1 种基金the Excellent Youth Fund of Liaoning Natural Science Foundation(No.2023JH3/10200001)the Fundamental Research Funds for the Central Universities(No.N2425004).
文摘The transient phenomena of re-oxidation and slag entrapment occurring in the tundish during the ladle change-over process have been proven detrimental to clean steel production.Therefore,an unsteady three-phase turbulence model,coupling velocity,temperature,and phase field was established to study the effect of the ladle shroud immersion depth on the slag eye formation,slag entrainment,slag dragging,air dragging,and flow characteristics during the ladle change-over process of a two-strand tundish.The results showed that reducing the immersion depth decreases the high-velocity region area under the slag layer in the quasi-steady process.During the emptying stage,as the molten bath level gradually decreases,the outlet temperature exhibits a trend of initially decreasing and subsequently increasing across all three shroud immersion depths.However,under a 210 mm shroud immersion depth,molten slag and air are dragged into the shroud,forming slag droplets and causing significant fluctuations,with a maximum scalar velocity of 0.0764 m/s at the monitoring point.In the filling stage,air and molten slag are dragged into the molten bath,forming bubbles and slag droplets at an immersion depth of 210 mm.Bubbles are observed within the molten slag layer,which can readily cause an emulsification phenomenon,making it easier to be dragged as slag droplets.Additionally,the slag eye area measured under 210 mm immersion depth at 45 s is 0.303 m^(2),while the maximum scalar velocity of 2.4259 m/s is detected at 12 s.At an immersion depth of 360 mm,the average area of the slag eye is minimized to 0.06268 m2,with corresponding variances of 0.006753,representing the optimal immersion depth.
基金supported by the National Natural Science Foundation of China(Grant No.52374317).
文摘Understanding the bubble behaviours and flow characteristics of large-capacity bottom-blowing electric arc furnace(EAF)is crucial for potential exogenous gas-induced slag foaming process and enhancement of molten bath dynamics.A physical model and a 3D gas-slag-steel transient bottom-blowing numerical model of a 150 t EAF were established to investigate the bubble behaviour and flow characteristics throughout the molten steel bath and slag layer under bottom-blowing,with referring to gas flow rate,plug diameter,plug arrangement and injection angle.Results indicate that the average bubble sizes experience increase,dynamic stability and decrease in molten steel bath and then undergo decrease and increase after entering into slag layer for all bottom-blowing modes.The bubble numbers exhibit the opposing trends during the process.Increase in gas flow rate leads to a significant rise in average bubble size but a decrease in number,average dwelling time and the spread area of bubbles in slag layer.Increase in plug diameter causes an opposite impact.The effect of plug arrangement radii on bubbles is almost negligible.Increasing the injection angle results in an increase in bubble size and a decrease in both bubble number and dwelling time in slag layer.The slag foaming potential was discussed referring to the bubble size,number and dwelling time in slag layer.Increase in gas flow rate and plug diameters can significantly enhance the fluids flow through increasing average flow velocity,decreasing mixing time and dead zone ratio of molten bath.Plug arrangement radius and injection angle express nonlinear correlation with average flow velocity and dead zone ratio,and the plug arrangement radius of 0.5R(R represents the radius of bottom circle of EAF model)and injection angle of 15°perform better in enhancing dynamics of molten bath.A group of bottom-blowing parameters are proposed to achieve better comprehensive performance of bubble-induced slag foaming and molten bath dynamics.
基金the Natural Science Foundation of China(Project for Young Scientists:Grant No.52105010,Regular Project:Grant No.62173096)Natural Science Foundationof Guangdong Province(Regular Project:Grant No.2025A1515012124,Grant No.2022A1515010327)Guangdong-Hong Kong-Macao Key Laboratory of Multi-scaleInformation Fusion and Collaborative Optimization Control Manufacturing Process.
文摘Legged robots have considerable potential for traversing unstructured situations;nonetheless,their inflexible frameworks often constrain adaptability and obstacle negotiation.The study article presents a revolutionary Soft Tri-Legged Robot(STLR)that improves movement and obstacle-avoidance skills by using a bio-inspired pneumatic artificial muscle(Bubble Artificial Muscles)and a bio-inspired tactile sensor(TacTip).The STLR is activated by BAMs,which are flexible,pneu-matic-driven actuators that provide fine control over forward,backward,and steering movements.Obstacle identification and avoidance are facilitated by the TacTip sensor,which delivers tactile input for traversing unstructured terrains.We delineate the mechanical features of the BAMs,assess the functionality of the robot's legs,and elaborate on the incorpora-tion of the tactile sensing system.Experimental results demonstrate that the STLR can effectively achieve multi-directional flexible movement and obstacle avoidance through a cross-modal perception-actuation mechanism.This study highlights the promise of soft robotics for search and rescue,medical aid,and autonomous exploration,while delineating difficulties and opportunities for future improvements in functionality and efficiency.
基金supported by the National Natural Science Foundation of China(Nos.U22B2067 and 52073176).
文摘350 keV He^(+) ions were injected into laser powder bed fusion(LPBF)-processed 304L stainless steel and traditional rolled 304L stainless steel with a flux of 1×10^(17) ions/cm^(2) at room temperature,followed by annealing at 750℃ for 10,100,and 300 h,respectively.The results showed that material swelling due to helium bubble coarsening was almost not observed in either the LPBF or rolled samples after 10 h of annealing duration.Rapid coarsening and swelling of bubbles occurred in the rolled samples,but only moderate bubble growth occurred in the LPBF sample after annealing for 100 h.After annealing for 300 h,the helium bubbles in both samples tended to grow steadily.For 10 h of annealing,the irradiated samples were in a disequilibrium state,and the apparent activation energy(E^(act))calculated by the Arrhenius model determined that helium atoms tended to diffuse through the displacement mechanism,and helium bubbles grew under the migration and coalescence(MC)mechanism.With annealing times over 100 h,the high-density dislocations and nano-oxide particles in the LPBF sample still had a strong trapping effect on the movement and growth of helium bubbles.After annealing for 300 h,the cellular subgrains in the LPBF sample decomposed,and the nano-oxide particles had no trapping effect on the helium bubbles.At this time,the dislocation structure played a primary role in suppressing the growth of helium bubbles,and the radiation resistance of the LPBF sample remained superior to that of the rolled samples.
基金supported by a grant from China railway corporation science and technology research and development plan project(Grant No.2017G005-B)funding support by Wuyi University’s Hong Kong and Macao Joint Research and Development Fund(Grants No.2021WGALH15)funding support by the Innovation and Technology Commission of Hong Kong SAR Government to the Hong Kong Branch of National Rail Transit Electrification and Automation Engineering Technology Research Center(Grant No.K-BBY1).
文摘The current technical standards primarily relied on experience to judge the interfacial bonding properties between the self-compacting concrete filling layer and the steam-cured concrete precast slab in CRTS Ⅲ slab ballastless track structure.This study sought to enhance technical standards for evaluating interfacial bonding properties by suggesting the use of the splitting tensile strength to evaluate the impact of bubble defects.Specimens were fabricated through on-site experiment.The percent of each area of 6 cm^(2)or more bubble defect was 0 in most of specimens.When the cumulative area of all bub-ble defects reached 12%,the splitting tensile strength value was 0.67 MPa,which exceeded the minimum required value of 0.5 MPa for ensuring bonding interface adhesion.Furthermore,when the cumulative area of all bubble defects reached 8%,the splitting tensile strength value was 0.85 MPa,which exceeded the minimum required value of 0.8 MPa,thereby over-coming the negative impact of each area of 10 cm^(2) or more bubble defect.Additionally,keeping the cumulative area of each area of 6 cm^(2) or more bubble defect below 6%ensured adequate bonding strength and reduced the occurrence of specimens with lower splitting tensile strength values.
基金supported by the National Natural Science Foundation of China(Grant No.12172063).
文摘The damage evolution of polycrystalline Al with helium(He)bubbles under strongly decaying shock waves is studied by molecular dynamics simulations.A new damage region is observed near the loading side of the sample,and the evolution characteristics and underlying mechanisms are elucidated.The development of damage in the new damage region begins after complete unloading of the incident shock wave and is further enhanced when the tensile stress arrives later.The damage evolution is completely controlled by the expansion-merging of He bubbles,without nucleation–growth of voids.This new damage region can be divided into two sections,each of which exhibits a unique dominant mechanism.The damage in the section closer to the loading side is due to the reverse velocity gradient formed after complete unloading of the incident shock wave,depending on the rate of decrease and the amplitude of the initial peak pressure.A high initial peak pressure that can lead to melting of material near the loading side is a necessary condition for the formation of the new damage region,since a significant reverse velocity gradient can only be established if melting occurs.The dominant mechanism in the section distant from the loading side is the action of tensile stress,associated with the profile of the incident shock wave upon reaching the free surface,which determines the material phase near the free surface.Moreover,the presence of He bubbles is another critical factor for formation of the new damage region,which does not occur in pure Al samples.
基金Supported by the State Key Laboratory of Chemical Engineering(SKL-ChE-16B01)China Postdoctoral Science Foundation(2016M601263)
文摘Local hydrodynamics of a gas–liquid–solid system,such as bubble circulation regime,gas holdup,liquid velocity and axial profile of solid concentration,are studied in a two-stage internal loop airlift reactor.Empirical correlations for gas holdup and liquid velocity are proposed to ease the reactor design and scale-up.Different bubble circulation regimes were displayed in the first(lower) and second(upper) stages.Increasing superficial gas velocity and solid loading can promote regime transition of the second stage,and the gas holdup of the second stage is higher than that of the lower stage.In addition,the effects of solid loading on bubble behaviour are experimentally investigated for each stage.It is found that bubble size in the downcomer decreases with the presence of solid particles,and bubble size distribution widens under higher superficial gas velocity and lower solid loading.
文摘A special experiment setup was designed to observe the interaction between bubbles and particle in flotation cell and to analyze the bubble characteristics such as bubble size, distribution and bubble-loading efficiency. Bubbles in water-gas system and three-phase system were measured. The results indicate that with the current setup the bubbles as small as 10 μm can be easily distinguished. The average size of the bubbles generated under the given conditions in two-phase system is 410 μm at frother concentration of 0.004%, which is in good correspondence with the results of other works. The effect of frother on bubble size was probed. Increasing frother concentration from 0 to 0.004% causes a reduction of bubble size from 700 to 400 μm. The bubble loading efficiency was reported. The result indicates that the fine particle is more easily entrapped than the coarse particle. Some factors, which have effect on measurement accuracy were discussed. The aeration speed has a significant effect on the accuracy of results, if it surpasses 30 mL/s, and the image becomes unclear due to the entrapment of fine particle. Another factor, which can affect observing results, is the sampling position. At a wrong sampling position, the images become unclear.
文摘In this paper,the failure caused by HRAM loads which were generated by high-speed projectile penetration,and protection technology of the fluid-filled structure were explored.A bubble was preset on the projectile trajectory in a fluid-filled structure.Based on the reflection and transmission phenomena of pressure waves at the gas-liquid interface and the compressibility characteristics of gases,a numerical analysis was conducted on the influence of preset bubble on projectile penetration and structural failure characteristics.The results indicate that the secondary water-entry impact phenomenon occurs when a preset bubble exists on the projectile trajectory,leading to the secondary water entry impact loads.The rarefaction waves reflected on the surface of the preset bubble cause the attenuation ratio of the initial impact pressure peak to reach 68.8%and the total specific impulse attenuation ratio to reach 48.6%.Furthermore,the larger the bubble,the faster the projectile,and the more obvious the attenuation effect.Moreover,due to the compressibility of the bubble,the global deformation attenuation ratio of the front and rear walls can reach over 80%.However,the larger the bubble size,the faster the projectile velocity,the smaller the local deformation attenuation effect of the rear wall,and the more severe the failure at the perforation of the rear wall.
基金JSPS KAKENHI Grant Number16H06286 supports global GNSS ionospheric maps (TEC,ROTI,and detrended TEC maps) developed by the Institute for SpaceEarth Environmental Research (ISEE) of Nagoya Universitysupport of the 2024 JASSO Follow-up Research Fellowship Program for a 90-day visiting research at the Institute for Space-Earth Environmental Research (ISEE),Nagoya University+3 种基金the support received from Telkom University under the“Skema Penelitian Terapan Periode I Tahun Anggaran 2024”the Memorandum of Understanding for Research Collaboration on Regional Ionospheric Observation (No:092/SAM3/TE-DEK/2021)the National Institute of Information and Communications Technology (NICT) International Exchange Program 2024-2025(No.2024-007)support for a one-year visiting research at Hokkaido University
文摘This paper highlights the crucial role of Indonesia’s GNSS receiver network in advancing Equatorial Plasma Bubble(EPB)studies in Southeast and East Asia,as ionospheric irregularities within EPB can disrupt GNSS signals and degrade positioning accuracy.Managed by the Indonesian Geospatial Information Agency(BIG),the Indonesia Continuously Operating Reference Station(Ina-CORS)network comprises over 300 GNSS receivers spanning equatorial to southern low-latitude regions.Ina-CORS is uniquely situated to monitor EPB generation,zonal drift,and dissipation across Southeast Asia.We provide a practical tool for EPB research,by sharing two-dimensional rate of Total Electron Content(TEC)change index(ROTI)derived from this network.We generate ROTI maps with a 10-minute resolution,and samples from May 2024 are publicly available for further scientific research.Two preliminary findings from the ROTI maps of Ina-CORS are noteworthy.First,the Ina-CORS ROTI maps reveal that the irregularities within a broader EPB structure persist longer,increasing the potential for these irregularities to migrate farther eastward.Second,we demonstrate that combined ROTI maps from Ina-CORS and GNSS receivers in East Asia and Australia can be used to monitor the development of ionospheric irregularities in Southeast and East Asia.We have demonstrated the combined ROTI maps to capture the development of ionospheric irregularities in the Southeast/East Asian sector during the G5 Geomagnetic Storm on May 11,2024.We observed simultaneous ionospheric irregularities in Japan and Australia,respectively propagating northwestward and southwestward,before midnight,whereas Southeast Asia’s equatorial and low-latitude regions exhibited irregularities post-midnight.By sharing ROTI maps from Indonesia and integrating them with regional GNSS networks,researchers can conduct comprehensive EPB studies,enhancing the understanding of EPB behavior across Southeast and East Asia and contributing significantly to ionospheric research.
基金Project supported by the Natural Science Foundation of Hubei Province(Grant No.2024AFD068).
文摘In recent years,the phenomenon of multistability has attracted wide attention.In this paper,a memristive chaotic system with extreme multistability is constructed by using a memristor.The dynamic behavior of the system is analyzed by Poincar´e mapping,a time series diagram,and a bifurcation diagram.The results show that the new system has several significant characteristics.First,the new system has a constant Lyapunov exponent,transient chaos and one complete Feigenbaum tree.Second,the system has the phenomenon of bifurcation map shifts that depend on the initial conditions.In addition,we find periodic bursting oscillations,chaotic bursting oscillations,and the transition of chaotic bursting oscillations to periodic bursting oscillations.In particular,when the system parameters take different discrete values,the system generates a bubble phenomenon that varies with the initial conditions,and this bubble can be shifted with the initial values,which has rarely been seen in the previous literature.The implementation by field-programmable gate array(FPGA)and analog circuit simulation show close alignment with the MATLAB numerical simulation results,validating the system’s realizability.Additionally,the image encryption algorithm integrating DNA-based encoding and chaotic systems further demonstrates its practical applicability.
文摘Bubbles play crucial roles in various fields,including naval and ocean engineering,chemical engineering,and biochemical engineering.Numerous theoretical analyses,numerical simulations,and experimental studies have been conducted to reveal the mysteries of bubble motion and its mechanisms.These efforts have significantly advanced research in bubble dynamics,where theoretical study is an efficient method for bubble motion prediction.Since Lord Rayleigh introduced the theoretical model of single-bubble motion in incompressible fluid in 1917,theoretical studies have been pivotal in understanding bubble dynamics.This study provides a comprehensive review of the development and applicability of theoretical studies in bubble dynamics using typical theoretical bubble models across different periods as a focal point and an overview of bubble theory applications in underwater explosion,marine cavitation,and seismic exploration.This study aims to serve as a reference and catalyst for further advancements in theoretical analysis and practical applications of bubble theory across marine fields.
基金funded by the National Natural Science Founda-tion of China(52071109).
文摘Unlike conventional spherical charges,a shaped charge generates not only a strong shock wave and a pulsating bubble,but also a high strain rate metal jet and a ballistic wave during the underwater explosion.They show significant characteristic differences and couple each other.This paper designs and conducts experiments with shaped charges to analyze the complicated process.The effects of liner angle and weight of shaped charge on the characteristics of metal jets,waves,and bubbles are discussed.It is found that in underwater explosions,the shaped charge generates the metal jet accompanied by the ballistic wave.Then,the shock wave propagates and superimposes with the ballistic wave,and the generated bubble pulsates periodically.It is revealed that the maximum head velocity of the metal jet versus the liner angle a and length-to-diameter ratio k of the shaped charge follows the laws of 1/(α/180°)^(0.55)andλ^(0.16),respectively.The head shape and velocity of the metal jet determine the curvature and propagation speed of the initial ballistic wave,thus impacting the superposition time and region with the shock wave.Our findings also reveal that the metal jet carries away some explosion products,which hinders the bubble development,causing an inward depression of the bubble wall near the metal jet.Therefore,the maximum bubble radius and pulsation period are 5.2%and 3.9%smaller than the spherical charge with the same weight.In addition,the uneven axial energy distribution of the shaped charge leads to an oblique bubble jet formation.
基金Funded by the National Natural Science Foundation of China(No.52172007)。
文摘To analyze the impact of bubbles on the mechanical behavior of glasses,by controlling the refining time,we prepared three borosilicate glasses with the same composition and different porosity.By the analysis software integrated within the optical microscope,the diameter and number of the bubbles on the surface of three borosilicate glasses were quantified.From the hardness and crack initiation resistance(CR),we built the relationship between the porosity and the mechanical performance of these borosilicate glasses.
