In this paper,electrically excited synchronous machines(EESMs)using copper(Cu)and aluminum(Al)windings are compared for the feasibility of replacing Cu windings with Al windings in electric vehicle(EV)applications sin...In this paper,electrically excited synchronous machines(EESMs)using copper(Cu)and aluminum(Al)windings are compared for the feasibility of replacing Cu windings with Al windings in electric vehicle(EV)applications since Al windings have lower mass density and cost per weight,but higher resistivity and lower thermal conductivity than Cu windings.The EESMs with four winding configurations are optimized with an electromagnetic-thermal co-optimization method.The optimized EESM with only Cu windings is considered as the baseline in this study.Results show that the EESM with stator-Cu/rotor-Al windings has the least torque reduction(12.1%)compared to the baseline among the three EESMs with Al windings and the highest torque mass density among all EESMs.Meanwhile,although the new European driving cycle efficiency of the stator-Cu/rotor-Al EESM is 1.8%lower than that of the baseline,the torque per cost is 71%higher,and the maximum rotor mechanical stress is 8%lower.Therefore,the EESMs with stator-Cu/rotor-Al windings are prospective substitutions of those with only Cu windings for EV applications considering the trade-off between performance and cost.展开更多
Under the strategic framework of rural revitalization and agricultural modernization, Xinjiashan Specialty Coffee Base, located in Zaotang Village, Lujiang Town, Longyang District, Baoshan City, has been proactively i...Under the strategic framework of rural revitalization and agricultural modernization, Xinjiashan Specialty Coffee Base, located in Zaotang Village, Lujiang Town, Longyang District, Baoshan City, has been proactively investigating innovative models for agricultural development. Through extensive communication and collaboration, this base has established close partnerships with research institutions including Kunming University of Science and Technology, Baoshan University, and Yunnan Academy of Agricultural Sciences, with a commitment to thoroughly exploring the potential for resource recycling and ecological complementarity. An innovative four-in-one three-dimensional integrated planting system incorporating "coffee, bananas, green manure, and bees" has been implemented. Concurrently, technological and digital management strategies have been comprehensively integrated to improve planting efficiency. Under this model, the proportion of specialty coffee attains 71%, and the per-unit yield is 17% greater than that of the conventional planting model. This approach not only substantially enhances economic returns but also promotes the integrated development of ecological and social benefits, offering a valuable practical example and experiential reference for the specialty and sustainable advancement of the coffee industry in comparable regions.展开更多
Aerial surveys are dynamic and continuous processes,and there are different height distributions of the ground in the measurement area,which leads to problems such as overlapping measurement areas and inaccurate altit...Aerial surveys are dynamic and continuous processes,and there are different height distributions of the ground in the measurement area,which leads to problems such as overlapping measurement areas and inaccurate altitude correction during the survey process.Commonly used terrain correction methods are based on the concept of finite elementization of ground surface radioactive sources,using GPS coordinates,radar altitude,and ground elevation distribution information from aerial surveys,combined with the sourceless efficiency calibration method to construct a response matrix,which is then inverted for surface nuclide content.However,most of the sourceless efficiency calibration methods used are numerical calculations that consider the body detector as a point detector and do not consider the changes in intrinsic detection efficiency under different incident directions of gamma rays.Therefore,when the altitude of the measurement area varies significantly or the flight altitude of the aerial survey is relatively low,such sourceless efficiency calibration method calculations tend to have a large bias,which affects the accuracy of the terrain correction.To address the above problems,this study employs a novel sourceless efficiency calibration method based on the Boolean operation of the ray deposition process and simplifies the traditional body source measurement model to a surface source measurement model to achieve fast and accurate efficiency calibration.Then,through the discretization of the measurement process,the static measurement process is superposed as equivalent to the dynamic measurement process,and the dynamic measurement response matrix is built and optimized based on the calibration method.Finally,the PSO-MLEM algorithm was used to solve the dynamic measurement response matrix to achieve dynamic terrain correction of aerial survey data.Analysis of the Baiyun'ebo test area revealed that,after applying dynamic terrain correction,the inverted anomalies in uranium(eU),thorium(eTh),and potassium(K)concentrations were closer to ground measurements(within 5.72%-30.79%)and exhibited clearer anomaly boundaries compared to traditional height-based corrections.However,owing to the inherent statistical fluctuations and characteristics of matrix inversion,higher measurement values tend to absorb lower ones,potentially enlarging the anomalous regions.Nevertheless,the highanomaly regions after inversion largely coincided with the ground truth validation,demonstrating that the proposed method can effectively correct airborne gamma spectrometry data.展开更多
In order to optimize the reaming process of the type IV composite hydrogen storage cylinder,the netting theory was employed for the design of stacking sequences,and the thickness in the head section was predicted.A fi...In order to optimize the reaming process of the type IV composite hydrogen storage cylinder,the netting theory was employed for the design of stacking sequences,and the thickness in the head section was predicted.A finite element model of the plastic-lined composite hydrogen storage cylinder,designed to withstand a working pressure of 70.0 MPa,was established by using the wound composite modeler(WCM)in the Abaqus software to analyze the forces acting on the winding layer.The Hashin failure criterion was utilized as the standard for assessing composite failure,and a progressive failure analysis of the cylinder was conducted to predict both the bursting pressure and the failure location of the composite hydrogen storage cylinder.The results indicate that the reaming process can effectively reduce the maximum filament winding thickness in the head section and promote a more uniform transition.At the bursting pressure,the stress within the head liner decreases,thereby enhancing the ultimate bearing capacity of the cylinder.A control system for a four-axis winding machine was designed by utilizing an industrial computer and a programmable multi-axis controller(PMAC).The winding line pattern is designed and the G-code trajectory is generated by the industrial computer.The numerical control system,composed of the PMAC and servo motor,executes the four-axis interpolation motion.展开更多
To ensure an uninterrupted power supply,mobile power sources(MPS)are widely deployed in power grids during emergencies.Comprising mobile emergency generators(MEGs)and mobile energy storage systems(MESS),MPS are capabl...To ensure an uninterrupted power supply,mobile power sources(MPS)are widely deployed in power grids during emergencies.Comprising mobile emergency generators(MEGs)and mobile energy storage systems(MESS),MPS are capable of supplying power to critical loads and serving as backup sources during grid contingencies,offering advantages such as flexibility and high resilience through electricity delivery via transportation networks.This paper proposes a design method for a 400 V–10 kV Dual-Winding Induction Generator(DWIG)intended for MEG applications,employing an improved particle swarmoptimization(PSO)algorithmbased on a back-propagation neural network(BPNN).A parameterized finite element(FE)model of the DWIG is established to derive constraints on its dimensional parameters,thereby simplifying the optimization space.Through sensitivity analysis between temperature rise and electromagnetic loss of the DWIG,the main factors influencing the machine’s temperature are identified,and electromagnetic loss is determined as the optimization objective.To obtain an accurate fitting function between electromagnetic loss and dimensional parameters,the BPNN is employed to predict the nonlinear relationship between the optimization objective and the parameters.The Latin hypercube sampling(LHS)method is used for random sampling in the FE model analysis for training,testing,and validation,which is then applied to compute the cost function in the PSO.Based on the relationships obtained by the BPNN,the PSO algorithm evaluates the fitness and cost functions to determine the optimal design point.The proposed optimization method is validated by comparing simulation results between the initial design and the optimized design.展开更多
Unmanned combat aerial vehicles require lightweight,stealth-capable exhaust systems.However,traditional metallic nozzles increase radar detectability and reduce range,while advanced composites offer high performance b...Unmanned combat aerial vehicles require lightweight,stealth-capable exhaust systems.However,traditional metallic nozzles increase radar detectability and reduce range,while advanced composites offer high performance but are expensive.Therefore,to improve the operational range and survivability of unmanned combat aerial vehicles,a lightweight,high-temperature-resistant,oxidation-resistant,and low-observable composite exhaust nozzle is developed to replace conventional metallic straight-type nozzles.The nozzle features a double serpentine shape to reduce radar and infrared signatures and is manufactured as a monolithic structure using the filament winding process,accommodating the complex geometry and large size(length:1.8 m,width:0.8 m).The exhaust nozzle consists of a ceramic matrix composite made of silicon carbide fibers and a silicon oxycarbide matrix,which absorbs and scatters radio frequency signals while withstanding prolonged exposure to high-temperature(700℃)oxidizing environments typical of engine exhaust gases.The polysiloxane resin used to produce the silicon oxycarbide matrix poses significant challenges owing to its low tackiness and high viscosity variations depending on the presence of nanoparticles,making filament winding difficult.These challenges are addressed by optimizing resin viscosity and winding pattern design.As a result,the tensile strength of the composite specimens fabricated with the optimized viscosity increases by 228.03% before pyrolysis and 97.68%after pyrolysis,compared with that of the non-optimized specimens.In addition,the density and tensile strength of the composite processed via three cycles of polymer infiltration and pyrolysis increased by 13.08% and 80.37%,respectively,compared to those of the non-densified composite.High-temperature oxidation and flame tests demonstrate exceptional thermal and oxidative stability.Furthermore,when compared with carbon fiber-reinforced ceramic matrix composites,the developed composite exhibits a permittivity at least two levels lower and a reflection loss below7 dB within the frequency range of 9.3-10.9 GHz,underscoring its superior electromagnetic stealth performance.展开更多
According to the Mindlin plate theory and the first-order piston theory,this work obtains accurate closed-form eigensolutions for the flutter problem of three-dimensional(3D)rectangular laminated panels.The governing ...According to the Mindlin plate theory and the first-order piston theory,this work obtains accurate closed-form eigensolutions for the flutter problem of three-dimensional(3D)rectangular laminated panels.The governing differential equations are derived by the Hamilton's variational principle,and then solved by the iterative Separation-of-Variable(i SOV)method,which are applicable to arbitrary combinations of homogeneous Boundary Conditions(BCs).However,only the simply-support,clamped and cantilever panels are considered in this work for the sake of clarity.With the closed-form eigensolutions,the flutter frequency,flutter mode and flutter boundary are presented,and the effect of shear deformation and aerodynamic damping on flutter frequencies is investigated.Besides,the relation between panel energy and the work of aerodynamic load is discussed.The numerical comparisons reveal the following.(A)The flutter eigenvalues obtained by the present method are accurate,validated by the Finite Element Method(FEM)and the Galerkin method.(B)When the span-chord ratio is larger than 3,simplifying a 3D panel to 2D(two-dimensional)panel is reasonable and the relative differences of the flutter points predicted by the two models are less than one percent.(C)The reciprocal relationship between the mechanical energy of the panel and the work done by aerodynamic load is verified by using the present flutter eigenvalues and modes,further indicating the high accuracy of the present solutions.(D)The coupling of shear deformation and aerodynamic damping prevents frequency coalescing.展开更多
Measurements from a hyperspectral infrared(HIR) sounder onboard a satellite in geostationary orbit not only provide atmospheric thermodynamic information,but also can be used to infer dynamic information with high tem...Measurements from a hyperspectral infrared(HIR) sounder onboard a satellite in geostationary orbit not only provide atmospheric thermodynamic information,but also can be used to infer dynamic information with high temporal resolution.Radiance measurements from the Geostationary Interferometric Infrared Sounder(GIIRS),obtained with 15-min temporal resolution during Typhoon Maria(2018) and 30-min temporal resolution during Typhoon Lekima(2019),were used to derive three-dimensional(3D) horizontal winds by tracking the motion of atmospheric moisture.This work focused on the impact of assimilation of 3D winds on typhoon analyses and forecasts using the operational NWP model of the China Meteorological Administration(CMA-MESO),and improved understanding of the potential benefits of assimilating dynamic information from geostationary sounder data with higher temporal resolution.The standard deviation of the observations minus simulations revealed that the accuracy of the derived 3D winds with 15-min resolution was higher than that of derived winds with 30-min resolution.Experiments showed that the assimilation system can effectively absorb the information of the derived 3D winds,and that dynamic information from clear-sky areas can be transferred to typhoon areas.In typhoon prediction,assimilation of the derived 3D winds had greatest influence on the typhoon track,and less influence on the maximum wind speed.Assimilation of the derived 3D winds reduced the average track error by 17.4% for Typhoon Maria(2018) and by 3.5% for Typhoon Lekima(2019) during their entire 36-h forecasts initiated at different times.Assimilation of GIIRS dynamic information can substantially improve forecasts of heavy precipitation by CMAMESO.Results indicate that the assimilation of dynamic information from high-temporal-resolution geostationary HIR sounder data adds value for improved numerical weather prediction.展开更多
In this paper,a composite numerical scheme is proposed to solve the threedimensional Darcy-Forchheimer miscible displacement problem with positive semi-definite assumptions.A mixed finite element is used for the fow e...In this paper,a composite numerical scheme is proposed to solve the threedimensional Darcy-Forchheimer miscible displacement problem with positive semi-definite assumptions.A mixed finite element is used for the fow equation.The velocity and pressure are computed simultaneously.The accuracy of velocity is improved one order.The concentration equation is solved by using mixed finite element,multi-step difference and upwind approximation.A multi-step method is used to approximate time derivative for improving the accuracy.The upwind approximation and an expanded mixed finite element are adopted to solve the convection and diffusion,respectively.The composite method could compute the diffusion flux and its gradient.It possibly becomes an eficient tool for solving convection-dominated diffusion problems.Firstly,the conservation of mass holds.Secondly,the multi-step method has high accuracy.Thirdly,the upwind approximation could avoid numerical dispersion.Using numerical analysis of a priori estimates and special techniques of differential equations,we give an error estimates for a positive definite problem.Numerical experiments illustrate its computational efficiency and feasibility of application.展开更多
In this paper,a scheme of dual-Doppler radar wind analysis based on a three-dimensional variational method is proposed and performed in two steps.First,the horizontal wind field is simultaneously recovered through min...In this paper,a scheme of dual-Doppler radar wind analysis based on a three-dimensional variational method is proposed and performed in two steps.First,the horizontal wind field is simultaneously recovered through minimizing a cost function defined as a radial observation term with the standard conjugate gradient method,avoiding a weighting parameter specification step.Compared with conventional dual-Doppler wind synthesis approaches,this variational method minimizes errors caused by interpolation from radar observation to analysis grid in the iterative solution process,which is one of the main sources of errors.Then,through the accelerated Liebmann method,the vertical velocity is further reestimated as an extra step by solving the Poisson equation with impermeable conditions imposed at the ground and near the tropopause.The Poisson equation defined by the second derivative of the vertical velocity is derived from the mass continuity equation.Compared with the method proposed by O’Brien,this method is less sensitive to the uncertainty of the boundary conditions and has better stability and reliability.Furthermore,the method proposed in this paper is applied to Doppler radar observation of a squall line process.It is shown that the retrieved vertical wind profile agrees well with the vertical profile obtained with the velocity–azimuth display(VAD)method,and the retrieved radial velocity as well as the analyzed positive and negative velocity centers and horizontal wind shear of the squall line are in accord with radar observations.There is a good correspondence between the divergence field of the derived wind field and the vertical velocity.And,the horizontal and vertical circulations within and around the squall line,as well as strong updrafts,the associated downdrafts,and associated rear inflow of the bow echo,are analyzed well.It is worth mentioning that the variational method in this paper can be applied to simultaneously synthesize the three-dimensional wind field from multiple-Doppler radar observations.展开更多
A three-dimensional wind field analysis sollware based on the Beigng-Gucheng dual-Doppler weather radar system has been built, and evaluated by using the numerical cloud model producing storm flow and hydrometeor fiel...A three-dimensional wind field analysis sollware based on the Beigng-Gucheng dual-Doppler weather radar system has been built, and evaluated by using the numerical cloud model producing storm flow and hydrometeor fields. The effects of observation noise and the spatial distribution of wind field analysis error are also investigated.展开更多
To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D lea...To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D leader-following cooperative interception guidance law.First,in the LOS direction of the leader,an impact time-controlled guidance law is derived based on the fixed-time stability theory,which enables the leader to complete the interception task at a prespecified impact time.Next,in the LOS direction of the followers,by introducing a time consensus tracking error function,a fixed-time consensus tracking guidance law is investigated to guarantee the consensus tracking convergence of the time-to-go.Then,in the direction normal to the LOS,by combining the designed global integral sliding mode surface and the second-order Sliding Mode Control(SMC)theory,an innovative 3D LOS-angle-constrained interception guidance law is developed,which eliminates the reaching phase in the traditional sliding mode guidance laws and effectively saves energy consumption.Moreover,it effectively suppresses the chattering phenomenon while avoiding the singularity issue,and compensates for unknown interference caused by target maneuvering online,making it convenient for practical engineering applications.Finally,theoretical proof analysis and multiple sets of numerical simulation results verify the effectiveness,superiority,and robustness of the investigated guidance law.展开更多
Three-dimensional(3D)urban structures play a critical role in informing climate mitigation strategies aimed at the built environment and facilitating sustainable urban development.Regrettably,there exists a significan...Three-dimensional(3D)urban structures play a critical role in informing climate mitigation strategies aimed at the built environment and facilitating sustainable urban development.Regrettably,there exists a significant gap in detailed and consistent data on 3D building space structures with global coverage due to the challenges inherent in the data collection and model calibration processes.In this study,we constructed a global urban structure(GUS-3D)dataset,including building volume,height,and footprint information,at a 500 m spatial resolution using extensive satellite observation products and numerous reference building samples.Our analysis indicated that the total volume of buildings worldwide in2015 exceeded 1×10^(12)m^(3).Over the 1985 to 2015 period,we observed a slight increase in the magnitude of 3D building volume growth(i.e.,it increased from 166.02 km3 during the 1985–2000 period to 175.08km3 during the 2000–2015 period),while the expansion magnitudes of the two-dimensional(2D)building footprint(22.51×10^(3) vs 13.29×10^(3)km^(2))and urban extent(157×10^(3) vs 133.8×10^(3)km^(2))notably decreased.This trend highlights the significant increase in intensive vertical utilization of urban land.Furthermore,we identified significant heterogeneity in building space provision and inequality across cities worldwide.This inequality is particularly pronounced in many populous Asian cities,which has been overlooked in previous studies on economic inequality.The GUS-3D dataset shows great potential to deepen our understanding of the urban environment and creates new horizons for numerous 3D urban studies.展开更多
BACKGROUND Inguinal hernias are common after surgery.Tension-free repair is widely accepted as the main method for managing inguinal hernias.Adequate exposure,coverage,and repair of the myopectineal orifice(MPO)are ne...BACKGROUND Inguinal hernias are common after surgery.Tension-free repair is widely accepted as the main method for managing inguinal hernias.Adequate exposure,coverage,and repair of the myopectineal orifice(MPO)are necessary.However,due to differences in race and sex,people’s body shapes vary.According to European guidelines,the patch should measure 10 cm×15 cm.If any part of the MPO is dissected,injury to the nerves,vascular network,or organs may occur during surgery,thereby leading to inguinal discomfort,pain,and seroma formation after surgery.Therefore,accurate localization and measurement of the boundary of the MPO are crucial for selecting the optimal patch for inguinal hernia repair.AIM To compare the size of the MPO measured on three-dimensional multislice spiral computed tomography(CT)with that measured via laparoscopy and explore the relevant factors influencing the size of the MPO.METHODS Clinical data from 74 patients who underwent laparoscopic tension-free inguinal hernia repair at the General Surgery Department of the First Affiliated Hospital of Anhui University of Science and Technology between September 2022 and July 2024 were collected and analyzed retrospectively.Transabdominal preperitoneal was performed.Sixty-four males and 10 females,with an average age of 58.30±12.32 years,were included.The clinical data of the patients were collected.The boundary of the MPO was measured on three-dimensional CT images before surgery and then again during transabdominal preperitoneal.All the preoperative and intraoperative data were analyzed via paired t-tests.A t-test was used for comparisons of age,body mass index,and sex between the groups.In the comparative analysis,a P value less than 0.05 indicated a significant difference.RESULTS The boundaries of the MPO on 3-dimensional CT images measured 7.05±0.47 cm and 6.27±0.61 cm,and the area of the MPO was 19.54±3.33 cm^(2).The boundaries of the MPO during surgery were 7.18±0.51 cm and 6.17±0.40 cm.The errors were not statistically significant.However,the intraoperative BD(the width of the MPO,P=0.024,P<0.05)and preoperative AC(the length of the MPO,P=0.045,P<0.05)significantly differed according to sex.The AC and BD measurements before and during surgery were not significantly different according to age,body mass index,hernia side or hernia type(P>0.05).CONCLUSION The application of this technology can aid in determining the most appropriate dissection range and patch size.展开更多
With the development of high-frequency and highvoltagetraction machines(TM)incorporating hairpin windings(HW)and SiC inverters for electric vehicles(EV),both theinterturn voltage stress and temperature within HW are r...With the development of high-frequency and highvoltagetraction machines(TM)incorporating hairpin windings(HW)and SiC inverters for electric vehicles(EV),both theinterturn voltage stress and temperature within HW are rising,increasing the risk of partial discharge(PD),and presentingsignificant challenges to insulation safety.Therefore,this paperaddresses this issue and proposes potential solutions.Firstly,thepaper examines an 8-pole,48-slot,6-layer HW TM to highlightthe unique characteristics of this winding structure,and explainsthe uneven distribution of interturn voltage stress andtemperature.Subsequently,a high-frequency equivalent circuitmodel of the HW TM prototype is developed.The error ofsimulation and experiment is only 5.7%,which proves theaccuracy of the model.Then,an improved HW scheme isproposed to lower the maximum voltage stress by 29.3%.Furthermore,the temperature distribution of HW TM isanalyzed to facilitate a detailed examination of the impact oftemperature on insulation PD.Finally,the partial dischargeinception voltage(PDIV)of interturn insulation,consideringtemperature effects,is calculated and verified throughexperiment.The paper proposes a reliability-oriented designmethod and process for HW TM.It demonstrates that thereliability-oriented design can achieve PD-free performance inthe design stage of HW.展开更多
The development of efficient catalysts for hydrogen evolution reaction(HER)and oxygen evolution reaction(OER)is of great significance for the practical application of water splitting in alkaline electrolytes.Transitio...The development of efficient catalysts for hydrogen evolution reaction(HER)and oxygen evolution reaction(OER)is of great significance for the practical application of water splitting in alkaline electrolytes.Transition metal sulfide electrocatalysts have been widely recognized as efficient catalysts for water splitting in alkaline media.In this work,an original and efficient synthesis strategy is proposed for the fabrication of asymmetric anode(N-(Co-Cu)S_(x))and cathode(N-CoS/Cu_(2)S).Impressively,these electrodes exhibit superior performance,benefiting from the construction of three-dimensional(3D)structures and the electronic structure adjustment caused by N-doping with increased active sites,improved mass/charge transport and enhanced evolution and release of gas bubbles.Hence,N-(Co-Cu)S_(x)anode exhibits excellent OER performance with only 217 mV overpotential at 10 mA·cm^(-2),while N-CoS/Cu_(2)S cathode possesses excellent HER performance with only 67 mV overpotential at 10 mA·cm^(-2).N-(Co-Cu)S_(x)||N-CoS/Cu_(2)S electrolyzer presents a low cell voltage of 1.53 V at 10 mA·cm^(-2)toward overall water splitting,which is superior to most recently reported transition metal sulfide-based catalysts.展开更多
A numerical method to predict the bursting strength of filament wound composite rocket motor case is proposed here.This method can evaluate the longitudinal stress evolution of each composite layer as impregnated fila...A numerical method to predict the bursting strength of filament wound composite rocket motor case is proposed here.This method can evaluate the longitudinal stress evolution of each composite layer as impregnated filaments with fiber tension are wound layer by layer,and consider the effects of accumulated stress and deformation during filament winding on the bursting strength of composite case.Taking∅520 mm composite cases as a case study,the filament-winding-process-induced stress and deformation as well as progressive damage behavior are numerically predicted,followed by a comparison with experimental results.The numerical results show that the predicted bursting pressures for composite cases manufactured on the mandrels with and without a flexible component are 14.20 MPa and 21.40 MPa,respectively.These values exhibit slight deviation from the measured pressures of 13.50 MPa and 21.57 MPa.Moreover,the predicted damage locations,situated respectively in the dome and cylinder,agree well with the experimental observation.These observations indicate that use of flexible component reduces the load-bearing capacity of the domes.Furthermore,it validates the reliability and accuracy of the proposed numerical method in predicting the bursting strength of composite cases.展开更多
High-speed permanent magnet synchronous motors(PMSMs)have recently been widely applied in various applications.However,due to the increased rotor speed and operating frequency increase,the winding AC losses rise subst...High-speed permanent magnet synchronous motors(PMSMs)have recently been widely applied in various applications.However,due to the increased rotor speed and operating frequency increase,the winding AC losses rise substantially,posing risks to the safety operation.Accurate modeling of the AC losses has therefore become critical at the motor initial design stage.This paper reviews the main modeling methods for AC copper losses in PMSMs,including analytical methods,finite element methods,and hybrid modeling methods.The advantages and disadvantages of each method are analyzed in detail,and key issues in the modeling process are discussed.Finally,future research directions in AC copper loss modeling are explored,providing new insights for motor design and performance optimization.展开更多
It is of great importance to obtain precise trace data,as traces are frequently the sole visible and measurable parameter in most outcrops.The manual recognition and detection of traces on high-resolution three-dimens...It is of great importance to obtain precise trace data,as traces are frequently the sole visible and measurable parameter in most outcrops.The manual recognition and detection of traces on high-resolution three-dimensional(3D)models are relatively straightforward but time-consuming.One potential solution to enhance this process is to use machine learning algorithms to detect the 3D traces.In this study,a unique pixel-wise texture mapper algorithm generates a dense point cloud representation of an outcrop with the precise resolution of the original textured 3D model.A virtual digital image rendering was then employed to capture virtual images of selected regions.This technique helps to overcome limitations caused by the surface morphology of the rock mass,such as restricted access,lighting conditions,and shading effects.After AI-powered trace detection on two-dimensional(2D)images,a 3D data structuring technique was applied to the selected trace pixels.In the 3D data structuring,the trace data were structured through 2D thinning,3D reprojection,clustering,segmentation,and segment linking.Finally,the linked segments were exported as 3D polylines,with each polyline in the output corresponding to a trace.The efficacy of the proposed method was assessed using a 3D model of a real-world case study,which was used to compare the results of artificial intelligence(AI)-aided and human intelligence trace detection.Rosette diagrams,which visualize the distribution of trace orientations,confirmed the high similarity between the automatically and manually generated trace maps.In conclusion,the proposed semi-automatic method was easy to use,fast,and accurate in detecting the dominant jointing system of the rock mass.展开更多
Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade compone...Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.展开更多
基金supported in part by China Scholarship Council(CSC)under Grant 202206160023.
文摘In this paper,electrically excited synchronous machines(EESMs)using copper(Cu)and aluminum(Al)windings are compared for the feasibility of replacing Cu windings with Al windings in electric vehicle(EV)applications since Al windings have lower mass density and cost per weight,but higher resistivity and lower thermal conductivity than Cu windings.The EESMs with four winding configurations are optimized with an electromagnetic-thermal co-optimization method.The optimized EESM with only Cu windings is considered as the baseline in this study.Results show that the EESM with stator-Cu/rotor-Al windings has the least torque reduction(12.1%)compared to the baseline among the three EESMs with Al windings and the highest torque mass density among all EESMs.Meanwhile,although the new European driving cycle efficiency of the stator-Cu/rotor-Al EESM is 1.8%lower than that of the baseline,the torque per cost is 71%higher,and the maximum rotor mechanical stress is 8%lower.Therefore,the EESMs with stator-Cu/rotor-Al windings are prospective substitutions of those with only Cu windings for EV applications considering the trade-off between performance and cost.
文摘Under the strategic framework of rural revitalization and agricultural modernization, Xinjiashan Specialty Coffee Base, located in Zaotang Village, Lujiang Town, Longyang District, Baoshan City, has been proactively investigating innovative models for agricultural development. Through extensive communication and collaboration, this base has established close partnerships with research institutions including Kunming University of Science and Technology, Baoshan University, and Yunnan Academy of Agricultural Sciences, with a commitment to thoroughly exploring the potential for resource recycling and ecological complementarity. An innovative four-in-one three-dimensional integrated planting system incorporating "coffee, bananas, green manure, and bees" has been implemented. Concurrently, technological and digital management strategies have been comprehensively integrated to improve planting efficiency. Under this model, the proportion of specialty coffee attains 71%, and the per-unit yield is 17% greater than that of the conventional planting model. This approach not only substantially enhances economic returns but also promotes the integrated development of ecological and social benefits, offering a valuable practical example and experiential reference for the specialty and sustainable advancement of the coffee industry in comparable regions.
基金supported by the National Key Research and Development Program(No.2022YFC2807400)the National Natural Science Foundation of China(Nos.12265003 and 12205044)。
文摘Aerial surveys are dynamic and continuous processes,and there are different height distributions of the ground in the measurement area,which leads to problems such as overlapping measurement areas and inaccurate altitude correction during the survey process.Commonly used terrain correction methods are based on the concept of finite elementization of ground surface radioactive sources,using GPS coordinates,radar altitude,and ground elevation distribution information from aerial surveys,combined with the sourceless efficiency calibration method to construct a response matrix,which is then inverted for surface nuclide content.However,most of the sourceless efficiency calibration methods used are numerical calculations that consider the body detector as a point detector and do not consider the changes in intrinsic detection efficiency under different incident directions of gamma rays.Therefore,when the altitude of the measurement area varies significantly or the flight altitude of the aerial survey is relatively low,such sourceless efficiency calibration method calculations tend to have a large bias,which affects the accuracy of the terrain correction.To address the above problems,this study employs a novel sourceless efficiency calibration method based on the Boolean operation of the ray deposition process and simplifies the traditional body source measurement model to a surface source measurement model to achieve fast and accurate efficiency calibration.Then,through the discretization of the measurement process,the static measurement process is superposed as equivalent to the dynamic measurement process,and the dynamic measurement response matrix is built and optimized based on the calibration method.Finally,the PSO-MLEM algorithm was used to solve the dynamic measurement response matrix to achieve dynamic terrain correction of aerial survey data.Analysis of the Baiyun'ebo test area revealed that,after applying dynamic terrain correction,the inverted anomalies in uranium(eU),thorium(eTh),and potassium(K)concentrations were closer to ground measurements(within 5.72%-30.79%)and exhibited clearer anomaly boundaries compared to traditional height-based corrections.However,owing to the inherent statistical fluctuations and characteristics of matrix inversion,higher measurement values tend to absorb lower ones,potentially enlarging the anomalous regions.Nevertheless,the highanomaly regions after inversion largely coincided with the ground truth validation,demonstrating that the proposed method can effectively correct airborne gamma spectrometry data.
文摘In order to optimize the reaming process of the type IV composite hydrogen storage cylinder,the netting theory was employed for the design of stacking sequences,and the thickness in the head section was predicted.A finite element model of the plastic-lined composite hydrogen storage cylinder,designed to withstand a working pressure of 70.0 MPa,was established by using the wound composite modeler(WCM)in the Abaqus software to analyze the forces acting on the winding layer.The Hashin failure criterion was utilized as the standard for assessing composite failure,and a progressive failure analysis of the cylinder was conducted to predict both the bursting pressure and the failure location of the composite hydrogen storage cylinder.The results indicate that the reaming process can effectively reduce the maximum filament winding thickness in the head section and promote a more uniform transition.At the bursting pressure,the stress within the head liner decreases,thereby enhancing the ultimate bearing capacity of the cylinder.A control system for a four-axis winding machine was designed by utilizing an industrial computer and a programmable multi-axis controller(PMAC).The winding line pattern is designed and the G-code trajectory is generated by the industrial computer.The numerical control system,composed of the PMAC and servo motor,executes the four-axis interpolation motion.
基金funded by the Science and Technology Projects of State Grid Corporation of China(Project No.J2024136).
文摘To ensure an uninterrupted power supply,mobile power sources(MPS)are widely deployed in power grids during emergencies.Comprising mobile emergency generators(MEGs)and mobile energy storage systems(MESS),MPS are capable of supplying power to critical loads and serving as backup sources during grid contingencies,offering advantages such as flexibility and high resilience through electricity delivery via transportation networks.This paper proposes a design method for a 400 V–10 kV Dual-Winding Induction Generator(DWIG)intended for MEG applications,employing an improved particle swarmoptimization(PSO)algorithmbased on a back-propagation neural network(BPNN).A parameterized finite element(FE)model of the DWIG is established to derive constraints on its dimensional parameters,thereby simplifying the optimization space.Through sensitivity analysis between temperature rise and electromagnetic loss of the DWIG,the main factors influencing the machine’s temperature are identified,and electromagnetic loss is determined as the optimization objective.To obtain an accurate fitting function between electromagnetic loss and dimensional parameters,the BPNN is employed to predict the nonlinear relationship between the optimization objective and the parameters.The Latin hypercube sampling(LHS)method is used for random sampling in the FE model analysis for training,testing,and validation,which is then applied to compute the cost function in the PSO.Based on the relationships obtained by the BPNN,the PSO algorithm evaluates the fitness and cost functions to determine the optimal design point.The proposed optimization method is validated by comparing simulation results between the initial design and the optimized design.
基金supported by the Agency for Defense Development Grant Funded by the Korean Government(Grant No.912822501).
文摘Unmanned combat aerial vehicles require lightweight,stealth-capable exhaust systems.However,traditional metallic nozzles increase radar detectability and reduce range,while advanced composites offer high performance but are expensive.Therefore,to improve the operational range and survivability of unmanned combat aerial vehicles,a lightweight,high-temperature-resistant,oxidation-resistant,and low-observable composite exhaust nozzle is developed to replace conventional metallic straight-type nozzles.The nozzle features a double serpentine shape to reduce radar and infrared signatures and is manufactured as a monolithic structure using the filament winding process,accommodating the complex geometry and large size(length:1.8 m,width:0.8 m).The exhaust nozzle consists of a ceramic matrix composite made of silicon carbide fibers and a silicon oxycarbide matrix,which absorbs and scatters radio frequency signals while withstanding prolonged exposure to high-temperature(700℃)oxidizing environments typical of engine exhaust gases.The polysiloxane resin used to produce the silicon oxycarbide matrix poses significant challenges owing to its low tackiness and high viscosity variations depending on the presence of nanoparticles,making filament winding difficult.These challenges are addressed by optimizing resin viscosity and winding pattern design.As a result,the tensile strength of the composite specimens fabricated with the optimized viscosity increases by 228.03% before pyrolysis and 97.68%after pyrolysis,compared with that of the non-optimized specimens.In addition,the density and tensile strength of the composite processed via three cycles of polymer infiltration and pyrolysis increased by 13.08% and 80.37%,respectively,compared to those of the non-densified composite.High-temperature oxidation and flame tests demonstrate exceptional thermal and oxidative stability.Furthermore,when compared with carbon fiber-reinforced ceramic matrix composites,the developed composite exhibits a permittivity at least two levels lower and a reflection loss below7 dB within the frequency range of 9.3-10.9 GHz,underscoring its superior electromagnetic stealth performance.
基金support of the National Natural Science Foundation of China(No.12172023)。
文摘According to the Mindlin plate theory and the first-order piston theory,this work obtains accurate closed-form eigensolutions for the flutter problem of three-dimensional(3D)rectangular laminated panels.The governing differential equations are derived by the Hamilton's variational principle,and then solved by the iterative Separation-of-Variable(i SOV)method,which are applicable to arbitrary combinations of homogeneous Boundary Conditions(BCs).However,only the simply-support,clamped and cantilever panels are considered in this work for the sake of clarity.With the closed-form eigensolutions,the flutter frequency,flutter mode and flutter boundary are presented,and the effect of shear deformation and aerodynamic damping on flutter frequencies is investigated.Besides,the relation between panel energy and the work of aerodynamic load is discussed.The numerical comparisons reveal the following.(A)The flutter eigenvalues obtained by the present method are accurate,validated by the Finite Element Method(FEM)and the Galerkin method.(B)When the span-chord ratio is larger than 3,simplifying a 3D panel to 2D(two-dimensional)panel is reasonable and the relative differences of the flutter points predicted by the two models are less than one percent.(C)The reciprocal relationship between the mechanical energy of the panel and the work done by aerodynamic load is verified by using the present flutter eigenvalues and modes,further indicating the high accuracy of the present solutions.(D)The coupling of shear deformation and aerodynamic damping prevents frequency coalescing.
基金supported by the National Natural Science Foundation of China(Grant No.U2142201)the Fengyun Application Pion eering Project(Grant No.FY-APP-ZX-2022.01)。
文摘Measurements from a hyperspectral infrared(HIR) sounder onboard a satellite in geostationary orbit not only provide atmospheric thermodynamic information,but also can be used to infer dynamic information with high temporal resolution.Radiance measurements from the Geostationary Interferometric Infrared Sounder(GIIRS),obtained with 15-min temporal resolution during Typhoon Maria(2018) and 30-min temporal resolution during Typhoon Lekima(2019),were used to derive three-dimensional(3D) horizontal winds by tracking the motion of atmospheric moisture.This work focused on the impact of assimilation of 3D winds on typhoon analyses and forecasts using the operational NWP model of the China Meteorological Administration(CMA-MESO),and improved understanding of the potential benefits of assimilating dynamic information from geostationary sounder data with higher temporal resolution.The standard deviation of the observations minus simulations revealed that the accuracy of the derived 3D winds with 15-min resolution was higher than that of derived winds with 30-min resolution.Experiments showed that the assimilation system can effectively absorb the information of the derived 3D winds,and that dynamic information from clear-sky areas can be transferred to typhoon areas.In typhoon prediction,assimilation of the derived 3D winds had greatest influence on the typhoon track,and less influence on the maximum wind speed.Assimilation of the derived 3D winds reduced the average track error by 17.4% for Typhoon Maria(2018) and by 3.5% for Typhoon Lekima(2019) during their entire 36-h forecasts initiated at different times.Assimilation of GIIRS dynamic information can substantially improve forecasts of heavy precipitation by CMAMESO.Results indicate that the assimilation of dynamic information from high-temporal-resolution geostationary HIR sounder data adds value for improved numerical weather prediction.
基金supported by the Natural Science Foundation of Shandong Province(ZR2021MA019)the National Natural Science Foundation of China(11871312)。
文摘In this paper,a composite numerical scheme is proposed to solve the threedimensional Darcy-Forchheimer miscible displacement problem with positive semi-definite assumptions.A mixed finite element is used for the fow equation.The velocity and pressure are computed simultaneously.The accuracy of velocity is improved one order.The concentration equation is solved by using mixed finite element,multi-step difference and upwind approximation.A multi-step method is used to approximate time derivative for improving the accuracy.The upwind approximation and an expanded mixed finite element are adopted to solve the convection and diffusion,respectively.The composite method could compute the diffusion flux and its gradient.It possibly becomes an eficient tool for solving convection-dominated diffusion problems.Firstly,the conservation of mass holds.Secondly,the multi-step method has high accuracy.Thirdly,the upwind approximation could avoid numerical dispersion.Using numerical analysis of a priori estimates and special techniques of differential equations,we give an error estimates for a positive definite problem.Numerical experiments illustrate its computational efficiency and feasibility of application.
基金supported by the National Key Research and Development Program of China(Grant No.2019YFC1510400)the National Natural Science Foundation of China(Grant Nos.41975054 and 41930967)the Special Fund for Forecasters of China Meteorological Administration(Grant No.CMAYBY2018-040)。
文摘In this paper,a scheme of dual-Doppler radar wind analysis based on a three-dimensional variational method is proposed and performed in two steps.First,the horizontal wind field is simultaneously recovered through minimizing a cost function defined as a radial observation term with the standard conjugate gradient method,avoiding a weighting parameter specification step.Compared with conventional dual-Doppler wind synthesis approaches,this variational method minimizes errors caused by interpolation from radar observation to analysis grid in the iterative solution process,which is one of the main sources of errors.Then,through the accelerated Liebmann method,the vertical velocity is further reestimated as an extra step by solving the Poisson equation with impermeable conditions imposed at the ground and near the tropopause.The Poisson equation defined by the second derivative of the vertical velocity is derived from the mass continuity equation.Compared with the method proposed by O’Brien,this method is less sensitive to the uncertainty of the boundary conditions and has better stability and reliability.Furthermore,the method proposed in this paper is applied to Doppler radar observation of a squall line process.It is shown that the retrieved vertical wind profile agrees well with the vertical profile obtained with the velocity–azimuth display(VAD)method,and the retrieved radial velocity as well as the analyzed positive and negative velocity centers and horizontal wind shear of the squall line are in accord with radar observations.There is a good correspondence between the divergence field of the derived wind field and the vertical velocity.And,the horizontal and vertical circulations within and around the squall line,as well as strong updrafts,the associated downdrafts,and associated rear inflow of the bow echo,are analyzed well.It is worth mentioning that the variational method in this paper can be applied to simultaneously synthesize the three-dimensional wind field from multiple-Doppler radar observations.
文摘A three-dimensional wind field analysis sollware based on the Beigng-Gucheng dual-Doppler weather radar system has been built, and evaluated by using the numerical cloud model producing storm flow and hydrometeor fields. The effects of observation noise and the spatial distribution of wind field analysis error are also investigated.
文摘To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D leader-following cooperative interception guidance law.First,in the LOS direction of the leader,an impact time-controlled guidance law is derived based on the fixed-time stability theory,which enables the leader to complete the interception task at a prespecified impact time.Next,in the LOS direction of the followers,by introducing a time consensus tracking error function,a fixed-time consensus tracking guidance law is investigated to guarantee the consensus tracking convergence of the time-to-go.Then,in the direction normal to the LOS,by combining the designed global integral sliding mode surface and the second-order Sliding Mode Control(SMC)theory,an innovative 3D LOS-angle-constrained interception guidance law is developed,which eliminates the reaching phase in the traditional sliding mode guidance laws and effectively saves energy consumption.Moreover,it effectively suppresses the chattering phenomenon while avoiding the singularity issue,and compensates for unknown interference caused by target maneuvering online,making it convenient for practical engineering applications.Finally,theoretical proof analysis and multiple sets of numerical simulation results verify the effectiveness,superiority,and robustness of the investigated guidance law.
基金supported by the National Science Fund for Distinguished Young Scholars(42225107)the National Natural Science Foundation of China(42001326,42371414,42171409,and 42271419)+1 种基金the Natural Science Foundation of Guangdong Province of China(2022A1515012207)the Basic and Applied Basic Research Project of Guangzhou Science and Technology Planning(202201011539)。
文摘Three-dimensional(3D)urban structures play a critical role in informing climate mitigation strategies aimed at the built environment and facilitating sustainable urban development.Regrettably,there exists a significant gap in detailed and consistent data on 3D building space structures with global coverage due to the challenges inherent in the data collection and model calibration processes.In this study,we constructed a global urban structure(GUS-3D)dataset,including building volume,height,and footprint information,at a 500 m spatial resolution using extensive satellite observation products and numerous reference building samples.Our analysis indicated that the total volume of buildings worldwide in2015 exceeded 1×10^(12)m^(3).Over the 1985 to 2015 period,we observed a slight increase in the magnitude of 3D building volume growth(i.e.,it increased from 166.02 km3 during the 1985–2000 period to 175.08km3 during the 2000–2015 period),while the expansion magnitudes of the two-dimensional(2D)building footprint(22.51×10^(3) vs 13.29×10^(3)km^(2))and urban extent(157×10^(3) vs 133.8×10^(3)km^(2))notably decreased.This trend highlights the significant increase in intensive vertical utilization of urban land.Furthermore,we identified significant heterogeneity in building space provision and inequality across cities worldwide.This inequality is particularly pronounced in many populous Asian cities,which has been overlooked in previous studies on economic inequality.The GUS-3D dataset shows great potential to deepen our understanding of the urban environment and creates new horizons for numerous 3D urban studies.
基金Supported by the 2022 Provincial Quality Engineering Project for Higher Education Institutions,No.2022sx031the 2023 Provincial Quality Engineering Project for Higher Education Institutions,No.2023jyxm1071.
文摘BACKGROUND Inguinal hernias are common after surgery.Tension-free repair is widely accepted as the main method for managing inguinal hernias.Adequate exposure,coverage,and repair of the myopectineal orifice(MPO)are necessary.However,due to differences in race and sex,people’s body shapes vary.According to European guidelines,the patch should measure 10 cm×15 cm.If any part of the MPO is dissected,injury to the nerves,vascular network,or organs may occur during surgery,thereby leading to inguinal discomfort,pain,and seroma formation after surgery.Therefore,accurate localization and measurement of the boundary of the MPO are crucial for selecting the optimal patch for inguinal hernia repair.AIM To compare the size of the MPO measured on three-dimensional multislice spiral computed tomography(CT)with that measured via laparoscopy and explore the relevant factors influencing the size of the MPO.METHODS Clinical data from 74 patients who underwent laparoscopic tension-free inguinal hernia repair at the General Surgery Department of the First Affiliated Hospital of Anhui University of Science and Technology between September 2022 and July 2024 were collected and analyzed retrospectively.Transabdominal preperitoneal was performed.Sixty-four males and 10 females,with an average age of 58.30±12.32 years,were included.The clinical data of the patients were collected.The boundary of the MPO was measured on three-dimensional CT images before surgery and then again during transabdominal preperitoneal.All the preoperative and intraoperative data were analyzed via paired t-tests.A t-test was used for comparisons of age,body mass index,and sex between the groups.In the comparative analysis,a P value less than 0.05 indicated a significant difference.RESULTS The boundaries of the MPO on 3-dimensional CT images measured 7.05±0.47 cm and 6.27±0.61 cm,and the area of the MPO was 19.54±3.33 cm^(2).The boundaries of the MPO during surgery were 7.18±0.51 cm and 6.17±0.40 cm.The errors were not statistically significant.However,the intraoperative BD(the width of the MPO,P=0.024,P<0.05)and preoperative AC(the length of the MPO,P=0.045,P<0.05)significantly differed according to sex.The AC and BD measurements before and during surgery were not significantly different according to age,body mass index,hernia side or hernia type(P>0.05).CONCLUSION The application of this technology can aid in determining the most appropriate dissection range and patch size.
基金supported by the Project of National Natural Science Foundation of China under Grant 52407060 and 52422704supported by Liaoning Province science and technology plan doctoral project under Grant 2023-BSBA-255.
文摘With the development of high-frequency and highvoltagetraction machines(TM)incorporating hairpin windings(HW)and SiC inverters for electric vehicles(EV),both theinterturn voltage stress and temperature within HW are rising,increasing the risk of partial discharge(PD),and presentingsignificant challenges to insulation safety.Therefore,this paperaddresses this issue and proposes potential solutions.Firstly,thepaper examines an 8-pole,48-slot,6-layer HW TM to highlightthe unique characteristics of this winding structure,and explainsthe uneven distribution of interturn voltage stress andtemperature.Subsequently,a high-frequency equivalent circuitmodel of the HW TM prototype is developed.The error ofsimulation and experiment is only 5.7%,which proves theaccuracy of the model.Then,an improved HW scheme isproposed to lower the maximum voltage stress by 29.3%.Furthermore,the temperature distribution of HW TM isanalyzed to facilitate a detailed examination of the impact oftemperature on insulation PD.Finally,the partial dischargeinception voltage(PDIV)of interturn insulation,consideringtemperature effects,is calculated and verified throughexperiment.The paper proposes a reliability-oriented designmethod and process for HW TM.It demonstrates that thereliability-oriented design can achieve PD-free performance inthe design stage of HW.
基金supported by the Science and Technology Project of Southwest Petroleum University(No.2021JBGS03)the Local Science and Technology Development Fund Projects Guided by the Central Government of China(No.2021ZYD0060)+2 种基金the National Natural Science Foundation of China(Nos.22209143 and 52371241)Guangdong High-level Innovation Institute Project(Nos.2021B0909050001 and 2021CX02L365)Guangdong Basic and Applied Basic Research Foundation(No.2023B1515120095).
文摘The development of efficient catalysts for hydrogen evolution reaction(HER)and oxygen evolution reaction(OER)is of great significance for the practical application of water splitting in alkaline electrolytes.Transition metal sulfide electrocatalysts have been widely recognized as efficient catalysts for water splitting in alkaline media.In this work,an original and efficient synthesis strategy is proposed for the fabrication of asymmetric anode(N-(Co-Cu)S_(x))and cathode(N-CoS/Cu_(2)S).Impressively,these electrodes exhibit superior performance,benefiting from the construction of three-dimensional(3D)structures and the electronic structure adjustment caused by N-doping with increased active sites,improved mass/charge transport and enhanced evolution and release of gas bubbles.Hence,N-(Co-Cu)S_(x)anode exhibits excellent OER performance with only 217 mV overpotential at 10 mA·cm^(-2),while N-CoS/Cu_(2)S cathode possesses excellent HER performance with only 67 mV overpotential at 10 mA·cm^(-2).N-(Co-Cu)S_(x)||N-CoS/Cu_(2)S electrolyzer presents a low cell voltage of 1.53 V at 10 mA·cm^(-2)toward overall water splitting,which is superior to most recently reported transition metal sulfide-based catalysts.
基金supported by the National Natural Science Foundation of China(No.11902231)the Major Program(JD)of Hubei Province,China(No.2023BAA004).
文摘A numerical method to predict the bursting strength of filament wound composite rocket motor case is proposed here.This method can evaluate the longitudinal stress evolution of each composite layer as impregnated filaments with fiber tension are wound layer by layer,and consider the effects of accumulated stress and deformation during filament winding on the bursting strength of composite case.Taking∅520 mm composite cases as a case study,the filament-winding-process-induced stress and deformation as well as progressive damage behavior are numerically predicted,followed by a comparison with experimental results.The numerical results show that the predicted bursting pressures for composite cases manufactured on the mandrels with and without a flexible component are 14.20 MPa and 21.40 MPa,respectively.These values exhibit slight deviation from the measured pressures of 13.50 MPa and 21.57 MPa.Moreover,the predicted damage locations,situated respectively in the dome and cylinder,agree well with the experimental observation.These observations indicate that use of flexible component reduces the load-bearing capacity of the domes.Furthermore,it validates the reliability and accuracy of the proposed numerical method in predicting the bursting strength of composite cases.
基金supported in part by the National Natural Science Foundation of China under Grants 52025073 and 52377055。
文摘High-speed permanent magnet synchronous motors(PMSMs)have recently been widely applied in various applications.However,due to the increased rotor speed and operating frequency increase,the winding AC losses rise substantially,posing risks to the safety operation.Accurate modeling of the AC losses has therefore become critical at the motor initial design stage.This paper reviews the main modeling methods for AC copper losses in PMSMs,including analytical methods,finite element methods,and hybrid modeling methods.The advantages and disadvantages of each method are analyzed in detail,and key issues in the modeling process are discussed.Finally,future research directions in AC copper loss modeling are explored,providing new insights for motor design and performance optimization.
基金supported by grants from the Human Resources Development program (Grant No.20204010600250)the Training Program of CCUS for the Green Growth (Grant No.20214000000500)by the Korea Institute of Energy Technology Evaluation and Planning (KETEP)funded by the Ministry of Trade,Industry,and Energy of the Korean Government (MOTIE).
文摘It is of great importance to obtain precise trace data,as traces are frequently the sole visible and measurable parameter in most outcrops.The manual recognition and detection of traces on high-resolution three-dimensional(3D)models are relatively straightforward but time-consuming.One potential solution to enhance this process is to use machine learning algorithms to detect the 3D traces.In this study,a unique pixel-wise texture mapper algorithm generates a dense point cloud representation of an outcrop with the precise resolution of the original textured 3D model.A virtual digital image rendering was then employed to capture virtual images of selected regions.This technique helps to overcome limitations caused by the surface morphology of the rock mass,such as restricted access,lighting conditions,and shading effects.After AI-powered trace detection on two-dimensional(2D)images,a 3D data structuring technique was applied to the selected trace pixels.In the 3D data structuring,the trace data were structured through 2D thinning,3D reprojection,clustering,segmentation,and segment linking.Finally,the linked segments were exported as 3D polylines,with each polyline in the output corresponding to a trace.The efficacy of the proposed method was assessed using a 3D model of a real-world case study,which was used to compare the results of artificial intelligence(AI)-aided and human intelligence trace detection.Rosette diagrams,which visualize the distribution of trace orientations,confirmed the high similarity between the automatically and manually generated trace maps.In conclusion,the proposed semi-automatic method was easy to use,fast,and accurate in detecting the dominant jointing system of the rock mass.
基金Project supported by the National Natural Science Foundation of China(Nos.12372071 and 12372070)the Aeronautical Science Fund of China(No.2022Z055052001)the Foundation of China Scholarship Council(No.202306830079)。
文摘Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.
