A structured method to generate conformal finite element(FE)mesh for realistic 3D woven textile reinforced composite is proposed.It is based on a voxel structure mesh reconstruction framework and aims to provide accur...A structured method to generate conformal finite element(FE)mesh for realistic 3D woven textile reinforced composite is proposed.It is based on a voxel structure mesh reconstruction framework and aims to provide accurate composite model at yarn level with material properties ready for use in commercial FE software.The textile representative volume element(RVE)is generated at filament level implementing the digital element method.Yarn structure is determined by filament bundle with variant cross-section shapes along its path.Yarn surface is then extracted using the Delaunay triangulation algorithm and a surface mesh is initiated.Then,the mesh domain is defined and constructed by voxel structure.Periodic boundary conditions,inter-yarn,and yarnmatrix interfaces are eliminated by re-mesh and mesh optimization.An element splitting rule is established to split the voxel unit into sub-elements to create smooth interface.A 3D orthogonal weave fabric reinforced composite is generated and simulated under compressive load.The composite structure and damage morphology are in good agreement with those of the experiment.展开更多
To address the poor mechanical properties of polydimethylsiloxane(PDMS)and enhance the understanding of the reinforcement mechanisms of aerogel network structures in rubber matrices,this study reinforced PDMS using an...To address the poor mechanical properties of polydimethylsiloxane(PDMS)and enhance the understanding of the reinforcement mechanisms of aerogel network structures in rubber matrices,this study reinforced PDMS using an ordered interconnected three-dimensional montmorillonite(MMT)aerogel network.The average pore diameter of the aerogels was successfully reduced from 11.53μm to 2.51μm by adjusting the ratio of poly(vinyl alcohol)(PVA)to MMT via directional freezing.Changes in the aerogel network were observed in field emission scanning electron microscope(FESEM)images.After vacuum impregnation,the aerogel network structure of the composites was observed using FESEM.Tensile tests indicated that as the pore diameter decreased,the elongation at break of the composites first increased to a peak of329.61%before decreasing,while the tensile strength and Young's modulus continuously increased to their maximum values of 6.29 MPa and24.67 MPa,respectively.Meanwhile,FESEM images of the tensile cracks and fracture surfaces showed that with a reduction in aerogel pore diameter,the degrees of crack deflection and interfacial debonding increased,presenting a rougher fracture surface.These phenomena enable the composites to dissipate substantial energy during tension,thus effectively improving the mechanical strength of the composites.The present work elucidates the bearing of ordered three-dimensional aerogel network structures on the performance of rubber matrices and provides crucial theoretical insights and technical guidance for the creation and optimization of high-performance PDMS-based composites.展开更多
Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade compone...Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.展开更多
The development of graphene-based composites with low density,robust absorption,wide bandwidth and thin thickness remained a great challenge in the field of electromagnetic(EM)absorption.In this work,nitrogen-doped re...The development of graphene-based composites with low density,robust absorption,wide bandwidth and thin thickness remained a great challenge in the field of electromagnetic(EM)absorption.In this work,nitrogen-doped reduced graphene oxide/hollow cobalt ferrite(NRGO/hollow CoFe_(2)O_(4))composite aerogels were constructed by a solvothermal and hydrothermal two-step route.Results demonstrated that the as-fabricated composite aerogels had the ultralow density and a unique three-dimensional(3D)network structure,and lots of hollow CoFe_(2)O_(4)microspheres were almost homogeneously distributed on the wrinkled surfaces of lamellar NRGO.Moreover,superior EM absorbing capacity could be achieved by modulating the ferrite structure,addition amounts of hollow CoFe_(2)O_(4)and thicknesses.It was noteworthy that the NRGO/hollow CoFe_(2)O_(4)composite aerogel with the addition amount of ferrite of 15.0 mg pos-sessed the minimum reflection loss of-44.7 dB and maximum absorption bandwidth of 5.2 GHz(from 12.6 to 17.8 GHz)at a very thin thickness of 1.8 mm and filling ratio of 15.0 wt.%.Furthermore,the possible EM attenuation mechanism had been proposed.The results of this work would be helpful for developing RGO-based 3D composites as lightweight,thin and highly efficient EM wave absorbers.展开更多
Node interpolation cell method（NICM）is a micromechanics method employing the virtual displacement principle and the representative volume element（RVE）scheme to obtain the relationship between the global and the lo...Node interpolation cell method（NICM）is a micromechanics method employing the virtual displacement principle and the representative volume element（RVE）scheme to obtain the relationship between the global and the local strain.Mechanical properties of 2-D textile fabric reinforced ceramic matrix composites are predicted by NICM.Microstructures of 2-D woven and braided fabric reinforced composite are modeled by two kinds of RVE scheme.NICM is used to predict the macroscopic mechanical properties.The fill and warp yarns are simulated with cubic B-spline and their undulating forms are approximated by sinusoid.The effect of porosity on the fiber and matrix are considered as a reduction of elastic module.The connection of microstructure parameters and fiber volume fraction is modeled to investigate the reflection on the mechanical properties.The results predicted by NICM are compared with that by the finite element method（FEM）.The comparison shows that NICM is a valid and feasible method for predicting the mechanics properties of 2-D woven and braided fabric reinforced ceramic matrix composites.展开更多
A generalized analytical model is developed to predict progressive failure behavior of several types of textile composites,including plain weave composites,twill weave composites,two-dimensional tri-axially braided co...A generalized analytical model is developed to predict progressive failure behavior of several types of textile composites,including plain weave composites,twill weave composites,two-dimensional tri-axially braided composites and warpreinforced 2.5-dimensional braided composites.In this model,the unit cell(UC)of composite is firstly identified and reconstructed into a refined lamina structure with multiple equivalent lamina elements(ELEs)based on apt geometrical approximation and assumptions.Secondly,two-way coupled stress-strain responses within the UC(macro-scale)and ELE(meso-scale)are established through a universal series-parallel model(SPM).Finally,a progressive damage model,which consists of damage initiation criteria and a stiffness evolution strategy,is employed to predict damage behavior of the ELE.The analytical results including mechanical properties and progressive failure process are validated against the existing numerical and experimental ones in literature.The validated analytical model is then used to study the effects of global fiber volume fraction,braided angle,shear failure coefficient and selected failure criteria on stiffness,strength and failure process.The present results demonstrate the efficiency and generic capability of the present analytical model for predicting the mechanical responses of a range of textile composites.展开更多
As a two-dimensional(2D)material,graphene shows excellent advantages in the field of gas sensors due to its inherent large specific surface area and unique electrical properties.However,in the practical application of...As a two-dimensional(2D)material,graphene shows excellent advantages in the field of gas sensors due to its inherent large specific surface area and unique electrical properties.However,in the practical application of gas detection,graphene sheet is easy to form irreversible agglomeration and has some limitations such as low sensitivity,long response time and slow recovery speed,which greatly reduce its gas sensing performance.As a gas sensing material,three-dimensional(3D)porous graphene has been extensively studied in recent years owing to its larger specific surface area and stable structure.In order to synthesize graphene with different three-dimensional structures,many methods have been developed.Herein,the synthesis and assembly of three-dimensional graphene and its composites were reviewed,with emphasis on the application of three-dimensional graphene and its composites in the field of gas sensors.The challenges and development prospects of three-dimensional graphene materials in the application of gas sensors were briefly described.展开更多
Increasing demand for weight reduction and greater fuel efficiency continues to spur the use of composite materials in commercial aircraft structures. Subsequently, as composite aerostructures become larger and more c...Increasing demand for weight reduction and greater fuel efficiency continues to spur the use of composite materials in commercial aircraft structures. Subsequently, as composite aerostructures become larger and more complex, traditional autoclave manufacturing methods are becoming prohibitively expensive. This has prompted renewed interest in out-of-autoclave processing techniques in which resins are introduced into a reinforcing preform. However, the success of these resin infusion methods is highly dependent upon operator skill and experience, particularly in the development of new manufacturing strategies for complex parts. Process modeling, as a predictive computational tool, aims to address the issues of reliability and waste that result from traditional trial-and-error approaches. Basic modeling attempts, many of which are still used in industry, generally focus on simulating fluid flow through an isotropic porous reinforcement material. How- ever, recent efforts are beginning to account for the multiscale and multidisciplinary complexity of woven materials, in simulations that can provide greater fidelity. In particular, new multi-physics process models are able to better predict the infusion behavior through textiles by considering the effect of fabric deformation on permeability and porosity properties within the reinforcing material. In addition to reviewing pre- vious research related to process modeling and the current state of the art, this paper highlights the recent validation of a multi-physics process model against the experimental infusion of a complex double dome component. By accounting for deformation-dependent flow behavior, the multi-physics process model was able to predict realistic flow behavior, demonstrating considerable improvement over basic isotropic permeability models.展开更多
Damage assessments in three dimensional (3D) textile composites subjected to mechanical loading can be performed by non-destructive and destructive techniques.This paper applies the two techniques to investigate the f...Damage assessments in three dimensional (3D) textile composites subjected to mechanical loading can be performed by non-destructive and destructive techniques.This paper applies the two techniques to investigate the fracture behavior of 3D tufted textile composites.X-ray computed tomography as a non-destructive evaluation method is appropriate to detect damage locations and identify their progression in 3D textile composites.Destructive methods such as sectioning toward observing damage provide valuable information about damage patterns.The results of this research could be utilized to evaluate the initial cause of rupture in 3D tufted composites used in aerospace structures and analyze fracture modes and damage progression.展开更多
Polyvinyl alcohol hydrogels have been used in wearable devices due to their good flexibility and biocompatibility.However,due to the low thermal conductivity(κ)of pure hydrogel,its further application in high power d...Polyvinyl alcohol hydrogels have been used in wearable devices due to their good flexibility and biocompatibility.However,due to the low thermal conductivity(κ)of pure hydrogel,its further application in high power devices is limited.To solve this problem,melamine sponge(MS)was used as the skeleton to wrap boron nitride nanosheets(BNNS)through repeated layering assembly,successfully preparing a three-dimensional(3D)boron nitride network(BNNS@MS),and PVA hydrogels were formed in the pores of the network.Due to the existence of the continuous phonon conduction network,the BNNS@MS/PVA exhibited an improvedκ.When the content of BNNS is about 6 wt.%,κof the hydrogel was increased to 1.12 W m^(-1)K^(-1),about two times higher than that of pure hydrogel.The solid heat conduction network and liquid convection network cooperate to achieve good thermal management ability.Combined with its high specific heat capacity,the composites have an important application prospect in the field of wearable flexible electronic thermal management.展开更多
This study elaborates on the effects of matrix rigidity on the high-velocity impact behaviour of UHMWPE textile composites using experimental and numerical methods.Textile composite samples were manufactured of a plai...This study elaborates on the effects of matrix rigidity on the high-velocity impact behaviour of UHMWPE textile composites using experimental and numerical methods.Textile composite samples were manufactured of a plain-weave fabric(comprising Spectra?1000 fibres)and four different matrix materials.High-velocity impact tests were conducted by launching a spherical steel projectile to strike on the prepared samples via a gas gun.The experimental results showed that the textile composites gradually changed from a membrane stretching mode to a plate bending mode as the matrix rigidity and thickness increased.The composites deformed in the membrane stretching mode had higher impact resistance and energy absorption capacity,and it was found that the average energy absorption per ply was much higher in this mode,although the number of broken yarns was smaller in the perforated samples.Moreover,the flexible matrix composites always had higher perforation resistance but larger deformation than the rigid matrix counterparts in the tested thickness and velocity range.A novel numerical modelling approach with enhanced computational efficiency was proposed to simulate textile composites in mesoscale resolution.The simulation results revealed that stress and strain development in the more rigid matrix composite was localised in the vicinity of the impact location,leading to larger local deformation and inferior perforation resistance.展开更多
In this study,the sol-gel method was introduced to prepare the composite phase change material (CPCM). The CPCM was added to fabric with coating techniques and the thermal activity of modified fabric was studied. In a...In this study,the sol-gel method was introduced to prepare the composite phase change material (CPCM). The CPCM was added to fabric with coating techniques and the thermal activity of modified fabric was studied. In addition,the thermal property and the microstructure of CPCM were also discussed in detail by means of polarization microscope and differential scanning calorimeter,respectively. According to the analysis of main influencial factors of the property of CPCM,the optimal preparing technique was determined. It was proved that CPCM could exhibit a good thermal property while phase transformation process took place,and a better appearance of the fabric modified with CPCM could be obtained due to the fact that in a warm circumstance,the liquid-state phase change material could be firmly enwrapped and embedded in the three-dimensional network all the time during the phase transformation. Besides,the fabric treated with CPCM had a high phase-transition enthalpy and an appropriate phase-transition temperature. As a result,a desirable temperature-adjustable function appeared.展开更多
The 2D limit equilibrium method is widely used for slope stability analysis.However,with the advancement of dump engineering,composite slopes often exhibit significant 3D mechanical effects.Consequently,it is of signi...The 2D limit equilibrium method is widely used for slope stability analysis.However,with the advancement of dump engineering,composite slopes often exhibit significant 3D mechanical effects.Consequently,it is of significant importance to develop an effective 3D stability calculation method for composite slopes to enhance the design and stability control of open-pit slope engineering.Using the composite slope formed by the mining stope and inner dump in Baiyinhua No.1 and No.2 open-pit coal mine as a case study,this research investigates the failure mode of composite slopes and establishes spatial shape equations for the sliding mass.By integrating the shear resistance and sliding force of each row of microstrip columns onto the bottom surface of the strip corresponding to the main sliding surface,a novel 2D equivalent physical and mechanical parameters analysis method for the strips on the main sliding surface of 3D sliding masses is proposed.Subsequently,a comprehensive 3D stability calculation method for composite slopes is developed,and the quantitative relationship between the coordinated development distance and its 3D stability coefficients is examined.The analysis reveals that the failure mode of the composite slope is characterized by cutting-bedding sliding,with the arc serving as the side interface and the weak layer as the bottom interface,while the destabilization mechanism primarily involves shear failure.The spatial form equation of the sliding mass comprises an ellipsoid and weak plane equation.The analysis revealed that when the coordinated development distance is 1500 m,the error rate between the 3D stability calculation result and the 2D stability calculation result of the composite slope is less than 8%,thereby verifying the proposed analytical method of equivalent physical and mechanical parameters and the 3D stability calculation method for composite slopes.Furthermore,the3D stability coefficient of the composite slope exhibits an exponential correlation with the coordinated development distance,with the coefficient gradually decreasing as the coordinated development distance increases.These findings provide a theoretical guideline for designing similar slope shape parameters and conducting stability analysis.展开更多
Silica fibers-reinforced, fused silica composites were fabricated with repeated vacuum-assisted liquid-phase infiltration. The mechanical properties, thermal properties, and ablative properties of the samples were eva...Silica fibers-reinforced, fused silica composites were fabricated with repeated vacuum-assisted liquid-phase infiltration. The mechanical properties, thermal properties, and ablative properties of the samples were evaluated. The effect of the silica fiber content and treatment temperature on the flexural strength of the three-dimensional SiO2 （3-D SiO2） composites also was investigated. The SiO2 composites show good mechanical properties and excellent ablative performance. The flexural strength increases with an increase in silica fiber content, and decreases with an increase in treatment temperature. When the volume fraction of the silica fiber is 50vo1% and the treatment temperature is 700℃ the flexural strength of the composites reaches a maximum value of 78 MPa. By adding cyclohexanone surfactant, the infiltration property can be largely improved, resulting in the density of SiO2 composites increasing up to 1.65 g/cm^3. The fracture surfaces of the flexural specimens observed using SEM, show that the pseudoplasticity and the toughening mechanisms of the composites are caused by absorption of a lot of energy by interface debonding and fiber pulling out.展开更多
Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal...Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal mechanisms(MRMs)involved in the machining of PRMMCs.This paper develops a three-dimensional(3D)microstructure-based model for investigating the MRM and surface integrity of machined PRMMCs.To accurately mimic the actual microstructure of a PRMMC,polyhedrons were randomly distributed inside the matrix to represent irregular SiC particles.Particle fracture and matrix deformation and failure were taken into account.For the model’s capability comparison,a two-dimensional(2D)analysis was also conducted.Relevant cutting experiments showed that the established 3D model accurately predicted the material removal,chip morphology,machined surface finish,and cutting forces.It was found that the matrix-particle-tool interactions led to particle fractures,mainly in the primary shear and secondary deformation zones along the cutting path and beneath the machined surface.Particle fracture and dilodegment greatly influences the quality of a machined surface.It was also found that although a 2D model can reflect certain material removal features,its ability to predict microstructural variation is limited.展开更多
As a thermosetting resin with excellent properties,epoxy resin is used in many areas such as electronics,transportation,aerospace,and other fields.However,its relatively low thermal conductivity limits its wide applic...As a thermosetting resin with excellent properties,epoxy resin is used in many areas such as electronics,transportation,aerospace,and other fields.However,its relatively low thermal conductivity limits its wide application in more demanding fields.Here,a three-dimensional carbon(3DC)network was prepared through NaCl template-assisted in situ chemical vapor deposition(CVD)and used to reinforce epoxy resin for enhancing its thermal conductivity.The 3DC was prepared with a molar ratio of sodium atom to carbon atom of 100:20,and argon atmosphere in CVD led to an optimal improvement in the thermal conductivity of epoxy resin.The thermal conductivity of epoxy resin increased by 18%when the filling content was 3 wt.%of 3DC network because of the high contact area,uniform dispersion,and enhanced formation of conductive paths with epoxy resin.As the amount of 3DC addition increases,the thermal conductivity of composites also increases.As an innovative exploration,the work presented in this paper is of great significance for the thermal conductivity application of epoxy resin in the future.展开更多
Three-dimensional( 3 D) fabric composite is a newly developed sandwich structure,consisting of two identical parallel fabric decks woven integrally and mechanically together by means of vertical woven fabrics. In this...Three-dimensional( 3 D) fabric composite is a newly developed sandwich structure,consisting of two identical parallel fabric decks woven integrally and mechanically together by means of vertical woven fabrics. In this paper,six types of 3 D fabric sandwich composites were developed in terms of compressive and flexural properties as a function of pile height( 10, 20 and30 mm) and pile distance( 16, 24 and 32 mm) in pile structures. The mechanical characteristics and the damage modes of the 3 D fabric sandwich composites under compressive and flexural load conditions were investigated. Besides,the influence of pile height and pile distance on the 3 D fabric sandwich composites mechanical properties was analyzed. The results showed that the compressive properties decreased with the increase of the pile height and the pile distance. Flexural properties increased with the increase of pile height, while decreased with the increase of pile distance.展开更多
The effects of fiber volume fraction on damping properties of carbon fiber three-dimensional and five-directional( 3D-5Dir)braided carbon fiber / epoxyres in composite cantilever beams were studied by experimental mod...The effects of fiber volume fraction on damping properties of carbon fiber three-dimensional and five-directional( 3D-5Dir)braided carbon fiber / epoxyres in composite cantilever beams were studied by experimental modal analysis method. Meanwhile,carbon fiber plain woven laminated / epoxy resin composites with different fiber volume fraction were concerned for comparison. The experimental result of braided specimens shows that the first three orders of natural frequency increase and the first three orders of the damping ratios of specimens decrease, when the fiber volume fraction increases. Furthermore,larger fiber volume fraction will be valuable for the better anti-exiting property of braided composites,and get an opposite effect on dissipation of vibration energy. The fiber volume fraction is an important factor for vibration performance design of braided composites. The comparison between the braided specimens and laminated specimens reveals that 3D braided composites have a wider range of damping properties than laminated composites with the same fiber volume fractions.展开更多
Based on references, this paper further develops the composites of textile gradient structure, tests and analyses the mechanical properties of composites of gradient struture, moreover, makes a comparison between comp...Based on references, this paper further develops the composites of textile gradient structure, tests and analyses the mechanical properties of composites of gradient struture, moreover, makes a comparison between composites of gradient structure and common laminated composites.展开更多
The main objective of this research work was the development of novel and responsive nonwoven composite structures containing gelling materials for wound management. The development of novel all inclusive collagen boo...The main objective of this research work was the development of novel and responsive nonwoven composite structures containing gelling materials for wound management. The development of novel all inclusive collagen booster(CB) therapeutic nonwoven wound dressings was mainly focused on. It provides essential functional properties such as high absorption,vertical and lateral wicking,and antibacterial and acidic pH properties. The developed composite wound dressing consisted of carboxymethylcellulose(CMC) fibre and also it was reinforced with polylactic acid( PLA) fibre. The produced composite wound dressings were treated with two different CBs at 4% by using the spray method. The details of the CBs have not been disclosed in this paper due to the Intellectual Property Rights( IPR) issues. The important benefit of using CB treatment is that it allows the maintenance of an acidic pH environment at the wound area. It is well known that acidic pH reduces the wound healing time and enhances the wound healing process. Furthermore,one of the CBs not only promotes the proliferation of the epithelial cells in wounds but also can provide antibacterial action. The PLA fibre reinforced CMC composite dressing has enhanced wicking properties which help to minimise the pooling of exudate on the wound bed and as a result maceration is prevented. The CBs treated dressings maintain the wound bed in an acidic pH condition which also improves the wound healing process. In addition to the above-mentioned properties,the CB treatment imparts antimicrobial activity against Gram-positive and Gram-negative bacteria,thus resulting in the reduction in the propensity for wound infection. Ultimately,the research has proved that the 4% CB treatment enhances the antimicrobial activity and the acidic pH characteristics of the developed CMC /PLA composite wound dressings.展开更多
基金co-supported by the Chongqing Natural Science Foundation General Project,China(No.CSTB2022NSCQ-MSX1115)。
文摘A structured method to generate conformal finite element(FE)mesh for realistic 3D woven textile reinforced composite is proposed.It is based on a voxel structure mesh reconstruction framework and aims to provide accurate composite model at yarn level with material properties ready for use in commercial FE software.The textile representative volume element(RVE)is generated at filament level implementing the digital element method.Yarn structure is determined by filament bundle with variant cross-section shapes along its path.Yarn surface is then extracted using the Delaunay triangulation algorithm and a surface mesh is initiated.Then,the mesh domain is defined and constructed by voxel structure.Periodic boundary conditions,inter-yarn,and yarnmatrix interfaces are eliminated by re-mesh and mesh optimization.An element splitting rule is established to split the voxel unit into sub-elements to create smooth interface.A 3D orthogonal weave fabric reinforced composite is generated and simulated under compressive load.The composite structure and damage morphology are in good agreement with those of the experiment.
基金financially supported by the National Natural Science Foundation of China(Nos.21876164 and U2030203)A Project Funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions。
文摘To address the poor mechanical properties of polydimethylsiloxane(PDMS)and enhance the understanding of the reinforcement mechanisms of aerogel network structures in rubber matrices,this study reinforced PDMS using an ordered interconnected three-dimensional montmorillonite(MMT)aerogel network.The average pore diameter of the aerogels was successfully reduced from 11.53μm to 2.51μm by adjusting the ratio of poly(vinyl alcohol)(PVA)to MMT via directional freezing.Changes in the aerogel network were observed in field emission scanning electron microscope(FESEM)images.After vacuum impregnation,the aerogel network structure of the composites was observed using FESEM.Tensile tests indicated that as the pore diameter decreased,the elongation at break of the composites first increased to a peak of329.61%before decreasing,while the tensile strength and Young's modulus continuously increased to their maximum values of 6.29 MPa and24.67 MPa,respectively.Meanwhile,FESEM images of the tensile cracks and fracture surfaces showed that with a reduction in aerogel pore diameter,the degrees of crack deflection and interfacial debonding increased,presenting a rougher fracture surface.These phenomena enable the composites to dissipate substantial energy during tension,thus effectively improving the mechanical strength of the composites.The present work elucidates the bearing of ordered three-dimensional aerogel network structures on the performance of rubber matrices and provides crucial theoretical insights and technical guidance for the creation and optimization of high-performance PDMS-based composites.
基金Project supported by the National Natural Science Foundation of China(Nos.12372071 and 12372070)the Aeronautical Science Fund of China(No.2022Z055052001)the Foundation of China Scholarship Council(No.202306830079)。
文摘Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.
基金supported by the Foundation of Provincial Natural Science Research Project of Anhui Colleges(No.KJ2021ZD0047)the Anhui Provincial Natural Science Foundation(No.2008085J27)+1 种基金the China Postdoctoral Science Foundation(No.2019M652160)the Research Foundation of the Institute of Environment-friendly Materials and Occupational Health(Wuhu),Anhui University of Science and Technology(No.ALW2020YF05).
文摘The development of graphene-based composites with low density,robust absorption,wide bandwidth and thin thickness remained a great challenge in the field of electromagnetic(EM)absorption.In this work,nitrogen-doped reduced graphene oxide/hollow cobalt ferrite(NRGO/hollow CoFe_(2)O_(4))composite aerogels were constructed by a solvothermal and hydrothermal two-step route.Results demonstrated that the as-fabricated composite aerogels had the ultralow density and a unique three-dimensional(3D)network structure,and lots of hollow CoFe_(2)O_(4)microspheres were almost homogeneously distributed on the wrinkled surfaces of lamellar NRGO.Moreover,superior EM absorbing capacity could be achieved by modulating the ferrite structure,addition amounts of hollow CoFe_(2)O_(4)and thicknesses.It was noteworthy that the NRGO/hollow CoFe_(2)O_(4)composite aerogel with the addition amount of ferrite of 15.0 mg pos-sessed the minimum reflection loss of-44.7 dB and maximum absorption bandwidth of 5.2 GHz(from 12.6 to 17.8 GHz)at a very thin thickness of 1.8 mm and filling ratio of 15.0 wt.%.Furthermore,the possible EM attenuation mechanism had been proposed.The results of this work would be helpful for developing RGO-based 3D composites as lightweight,thin and highly efficient EM wave absorbers.
基金Supported by the Aviation Science Foundationof China(2009ZB5052)the Specialized Research Foundation for the Doctor Program of Higher Education(20070287039)~~
文摘Node interpolation cell method（NICM）is a micromechanics method employing the virtual displacement principle and the representative volume element（RVE）scheme to obtain the relationship between the global and the local strain.Mechanical properties of 2-D textile fabric reinforced ceramic matrix composites are predicted by NICM.Microstructures of 2-D woven and braided fabric reinforced composite are modeled by two kinds of RVE scheme.NICM is used to predict the macroscopic mechanical properties.The fill and warp yarns are simulated with cubic B-spline and their undulating forms are approximated by sinusoid.The effect of porosity on the fiber and matrix are considered as a reduction of elastic module.The connection of microstructure parameters and fiber volume fraction is modeled to investigate the reflection on the mechanical properties.The results predicted by NICM are compared with that by the finite element method（FEM）.The comparison shows that NICM is a valid and feasible method for predicting the mechanics properties of 2-D woven and braided fabric reinforced ceramic matrix composites.
基金supported by the National Nature Science Foundation of China(Grant Nos.11772267,12002111)the China Postdoctoral Science Foundation(Grant No.2020M681101)+1 种基金the Shaanxi Key Research and Development Program for International Cooperation and Exchanges(Grant 2019KW-020)the 111 Project(Grant BP0719007).
文摘A generalized analytical model is developed to predict progressive failure behavior of several types of textile composites,including plain weave composites,twill weave composites,two-dimensional tri-axially braided composites and warpreinforced 2.5-dimensional braided composites.In this model,the unit cell(UC)of composite is firstly identified and reconstructed into a refined lamina structure with multiple equivalent lamina elements(ELEs)based on apt geometrical approximation and assumptions.Secondly,two-way coupled stress-strain responses within the UC(macro-scale)and ELE(meso-scale)are established through a universal series-parallel model(SPM).Finally,a progressive damage model,which consists of damage initiation criteria and a stiffness evolution strategy,is employed to predict damage behavior of the ELE.The analytical results including mechanical properties and progressive failure process are validated against the existing numerical and experimental ones in literature.The validated analytical model is then used to study the effects of global fiber volume fraction,braided angle,shear failure coefficient and selected failure criteria on stiffness,strength and failure process.The present results demonstrate the efficiency and generic capability of the present analytical model for predicting the mechanical responses of a range of textile composites.
基金financially supported by the Graduate Scientific Research and Innovation Foundation of Chongqing,China(No.CYS20001)。
文摘As a two-dimensional(2D)material,graphene shows excellent advantages in the field of gas sensors due to its inherent large specific surface area and unique electrical properties.However,in the practical application of gas detection,graphene sheet is easy to form irreversible agglomeration and has some limitations such as low sensitivity,long response time and slow recovery speed,which greatly reduce its gas sensing performance.As a gas sensing material,three-dimensional(3D)porous graphene has been extensively studied in recent years owing to its larger specific surface area and stable structure.In order to synthesize graphene with different three-dimensional structures,many methods have been developed.Herein,the synthesis and assembly of three-dimensional graphene and its composites were reviewed,with emphasis on the application of three-dimensional graphene and its composites in the field of gas sensors.The challenges and development prospects of three-dimensional graphene materials in the application of gas sensors were briefly described.
基金supported under the Australian Research Council’s Linkage Projects funding scheme (LP100100508) at Monash University in partnership with Boeing Research & Technology Australiathe financial support of Bombardier and the Royal Academy of Engineering
文摘Increasing demand for weight reduction and greater fuel efficiency continues to spur the use of composite materials in commercial aircraft structures. Subsequently, as composite aerostructures become larger and more complex, traditional autoclave manufacturing methods are becoming prohibitively expensive. This has prompted renewed interest in out-of-autoclave processing techniques in which resins are introduced into a reinforcing preform. However, the success of these resin infusion methods is highly dependent upon operator skill and experience, particularly in the development of new manufacturing strategies for complex parts. Process modeling, as a predictive computational tool, aims to address the issues of reliability and waste that result from traditional trial-and-error approaches. Basic modeling attempts, many of which are still used in industry, generally focus on simulating fluid flow through an isotropic porous reinforcement material. How- ever, recent efforts are beginning to account for the multiscale and multidisciplinary complexity of woven materials, in simulations that can provide greater fidelity. In particular, new multi-physics process models are able to better predict the infusion behavior through textiles by considering the effect of fabric deformation on permeability and porosity properties within the reinforcing material. In addition to reviewing pre- vious research related to process modeling and the current state of the art, this paper highlights the recent validation of a multi-physics process model against the experimental infusion of a complex double dome component. By accounting for deformation-dependent flow behavior, the multi-physics process model was able to predict realistic flow behavior, demonstrating considerable improvement over basic isotropic permeability models.
文摘Damage assessments in three dimensional (3D) textile composites subjected to mechanical loading can be performed by non-destructive and destructive techniques.This paper applies the two techniques to investigate the fracture behavior of 3D tufted textile composites.X-ray computed tomography as a non-destructive evaluation method is appropriate to detect damage locations and identify their progression in 3D textile composites.Destructive methods such as sectioning toward observing damage provide valuable information about damage patterns.The results of this research could be utilized to evaluate the initial cause of rupture in 3D tufted composites used in aerospace structures and analyze fracture modes and damage progression.
基金the National Natural Science Foundation of China(Nos.52173078,52130303,and 51803151)the Young Elite Scientists Sponsorship Program by CAST(No.2019QNRC001)。
文摘Polyvinyl alcohol hydrogels have been used in wearable devices due to their good flexibility and biocompatibility.However,due to the low thermal conductivity(κ)of pure hydrogel,its further application in high power devices is limited.To solve this problem,melamine sponge(MS)was used as the skeleton to wrap boron nitride nanosheets(BNNS)through repeated layering assembly,successfully preparing a three-dimensional(3D)boron nitride network(BNNS@MS),and PVA hydrogels were formed in the pores of the network.Due to the existence of the continuous phonon conduction network,the BNNS@MS/PVA exhibited an improvedκ.When the content of BNNS is about 6 wt.%,κof the hydrogel was increased to 1.12 W m^(-1)K^(-1),about two times higher than that of pure hydrogel.The solid heat conduction network and liquid convection network cooperate to achieve good thermal management ability.Combined with its high specific heat capacity,the composites have an important application prospect in the field of wearable flexible electronic thermal management.
文摘This study elaborates on the effects of matrix rigidity on the high-velocity impact behaviour of UHMWPE textile composites using experimental and numerical methods.Textile composite samples were manufactured of a plain-weave fabric(comprising Spectra?1000 fibres)and four different matrix materials.High-velocity impact tests were conducted by launching a spherical steel projectile to strike on the prepared samples via a gas gun.The experimental results showed that the textile composites gradually changed from a membrane stretching mode to a plate bending mode as the matrix rigidity and thickness increased.The composites deformed in the membrane stretching mode had higher impact resistance and energy absorption capacity,and it was found that the average energy absorption per ply was much higher in this mode,although the number of broken yarns was smaller in the perforated samples.Moreover,the flexible matrix composites always had higher perforation resistance but larger deformation than the rigid matrix counterparts in the tested thickness and velocity range.A novel numerical modelling approach with enhanced computational efficiency was proposed to simulate textile composites in mesoscale resolution.The simulation results revealed that stress and strain development in the more rigid matrix composite was localised in the vicinity of the impact location,leading to larger local deformation and inferior perforation resistance.
基金Fujian Province I mportant Science and Technology Development Fund,China (No.2005Z17)
文摘In this study,the sol-gel method was introduced to prepare the composite phase change material (CPCM). The CPCM was added to fabric with coating techniques and the thermal activity of modified fabric was studied. In addition,the thermal property and the microstructure of CPCM were also discussed in detail by means of polarization microscope and differential scanning calorimeter,respectively. According to the analysis of main influencial factors of the property of CPCM,the optimal preparing technique was determined. It was proved that CPCM could exhibit a good thermal property while phase transformation process took place,and a better appearance of the fabric modified with CPCM could be obtained due to the fact that in a warm circumstance,the liquid-state phase change material could be firmly enwrapped and embedded in the three-dimensional network all the time during the phase transformation. Besides,the fabric treated with CPCM had a high phase-transition enthalpy and an appropriate phase-transition temperature. As a result,a desirable temperature-adjustable function appeared.
基金supported by the National Natural Science Foundation of China (No.52374124)National Youth Science Foundation of China (No.52204135)+3 种基金Xing Liao Talent Plan (No.XLYC2202004)Young Elite Scientists Sponsorship Program by CAST (No.2023QNRC001)Liaoning Province International Science and Technology Cooperation Plan (No.2022JH2/1070004)Liaoning Natural Science Foundation Program (No.2022-BS-327)。
文摘The 2D limit equilibrium method is widely used for slope stability analysis.However,with the advancement of dump engineering,composite slopes often exhibit significant 3D mechanical effects.Consequently,it is of significant importance to develop an effective 3D stability calculation method for composite slopes to enhance the design and stability control of open-pit slope engineering.Using the composite slope formed by the mining stope and inner dump in Baiyinhua No.1 and No.2 open-pit coal mine as a case study,this research investigates the failure mode of composite slopes and establishes spatial shape equations for the sliding mass.By integrating the shear resistance and sliding force of each row of microstrip columns onto the bottom surface of the strip corresponding to the main sliding surface,a novel 2D equivalent physical and mechanical parameters analysis method for the strips on the main sliding surface of 3D sliding masses is proposed.Subsequently,a comprehensive 3D stability calculation method for composite slopes is developed,and the quantitative relationship between the coordinated development distance and its 3D stability coefficients is examined.The analysis reveals that the failure mode of the composite slope is characterized by cutting-bedding sliding,with the arc serving as the side interface and the weak layer as the bottom interface,while the destabilization mechanism primarily involves shear failure.The spatial form equation of the sliding mass comprises an ellipsoid and weak plane equation.The analysis revealed that when the coordinated development distance is 1500 m,the error rate between the 3D stability calculation result and the 2D stability calculation result of the composite slope is less than 8%,thereby verifying the proposed analytical method of equivalent physical and mechanical parameters and the 3D stability calculation method for composite slopes.Furthermore,the3D stability coefficient of the composite slope exhibits an exponential correlation with the coordinated development distance,with the coefficient gradually decreasing as the coordinated development distance increases.These findings provide a theoretical guideline for designing similar slope shape parameters and conducting stability analysis.
文摘Silica fibers-reinforced, fused silica composites were fabricated with repeated vacuum-assisted liquid-phase infiltration. The mechanical properties, thermal properties, and ablative properties of the samples were evaluated. The effect of the silica fiber content and treatment temperature on the flexural strength of the three-dimensional SiO2 （3-D SiO2） composites also was investigated. The SiO2 composites show good mechanical properties and excellent ablative performance. The flexural strength increases with an increase in silica fiber content, and decreases with an increase in treatment temperature. When the volume fraction of the silica fiber is 50vo1% and the treatment temperature is 700℃ the flexural strength of the composites reaches a maximum value of 78 MPa. By adding cyclohexanone surfactant, the infiltration property can be largely improved, resulting in the density of SiO2 composites increasing up to 1.65 g/cm^3. The fracture surfaces of the flexural specimens observed using SEM, show that the pseudoplasticity and the toughening mechanisms of the composites are caused by absorption of a lot of energy by interface debonding and fiber pulling out.
文摘Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal mechanisms(MRMs)involved in the machining of PRMMCs.This paper develops a three-dimensional(3D)microstructure-based model for investigating the MRM and surface integrity of machined PRMMCs.To accurately mimic the actual microstructure of a PRMMC,polyhedrons were randomly distributed inside the matrix to represent irregular SiC particles.Particle fracture and matrix deformation and failure were taken into account.For the model’s capability comparison,a two-dimensional(2D)analysis was also conducted.Relevant cutting experiments showed that the established 3D model accurately predicted the material removal,chip morphology,machined surface finish,and cutting forces.It was found that the matrix-particle-tool interactions led to particle fractures,mainly in the primary shear and secondary deformation zones along the cutting path and beneath the machined surface.Particle fracture and dilodegment greatly influences the quality of a machined surface.It was also found that although a 2D model can reflect certain material removal features,its ability to predict microstructural variation is limited.
基金the Key Projects of Tianjin Natural Science Foundation(No.16ZXCLGX00130).
文摘As a thermosetting resin with excellent properties,epoxy resin is used in many areas such as electronics,transportation,aerospace,and other fields.However,its relatively low thermal conductivity limits its wide application in more demanding fields.Here,a three-dimensional carbon(3DC)network was prepared through NaCl template-assisted in situ chemical vapor deposition(CVD)and used to reinforce epoxy resin for enhancing its thermal conductivity.The 3DC was prepared with a molar ratio of sodium atom to carbon atom of 100:20,and argon atmosphere in CVD led to an optimal improvement in the thermal conductivity of epoxy resin.The thermal conductivity of epoxy resin increased by 18%when the filling content was 3 wt.%of 3DC network because of the high contact area,uniform dispersion,and enhanced formation of conductive paths with epoxy resin.As the amount of 3DC addition increases,the thermal conductivity of composites also increases.As an innovative exploration,the work presented in this paper is of great significance for the thermal conductivity application of epoxy resin in the future.
基金National Key R&D Program of China(Nos.2016YFB0303104,2018YFC0810306)Jiangsu Overseas Visiting Scholar Program for University Prominent Younge Middle-aged Teachers and PresidentsSix Talent Peaks Project in Jiangsu Province,China(No.XCL-061)
文摘Three-dimensional( 3 D) fabric composite is a newly developed sandwich structure,consisting of two identical parallel fabric decks woven integrally and mechanically together by means of vertical woven fabrics. In this paper,six types of 3 D fabric sandwich composites were developed in terms of compressive and flexural properties as a function of pile height( 10, 20 and30 mm) and pile distance( 16, 24 and 32 mm) in pile structures. The mechanical characteristics and the damage modes of the 3 D fabric sandwich composites under compressive and flexural load conditions were investigated. Besides,the influence of pile height and pile distance on the 3 D fabric sandwich composites mechanical properties was analyzed. The results showed that the compressive properties decreased with the increase of the pile height and the pile distance. Flexural properties increased with the increase of pile height, while decreased with the increase of pile distance.
基金Tianjin Municipal Science and Technologies Commission,China(Nos.10SYSYJC27800,1ZCKFSF00500)
文摘The effects of fiber volume fraction on damping properties of carbon fiber three-dimensional and five-directional( 3D-5Dir)braided carbon fiber / epoxyres in composite cantilever beams were studied by experimental modal analysis method. Meanwhile,carbon fiber plain woven laminated / epoxy resin composites with different fiber volume fraction were concerned for comparison. The experimental result of braided specimens shows that the first three orders of natural frequency increase and the first three orders of the damping ratios of specimens decrease, when the fiber volume fraction increases. Furthermore,larger fiber volume fraction will be valuable for the better anti-exiting property of braided composites,and get an opposite effect on dissipation of vibration energy. The fiber volume fraction is an important factor for vibration performance design of braided composites. The comparison between the braided specimens and laminated specimens reveals that 3D braided composites have a wider range of damping properties than laminated composites with the same fiber volume fractions.
文摘Based on references, this paper further develops the composites of textile gradient structure, tests and analyses the mechanical properties of composites of gradient struture, moreover, makes a comparison between composites of gradient structure and common laminated composites.
文摘The main objective of this research work was the development of novel and responsive nonwoven composite structures containing gelling materials for wound management. The development of novel all inclusive collagen booster(CB) therapeutic nonwoven wound dressings was mainly focused on. It provides essential functional properties such as high absorption,vertical and lateral wicking,and antibacterial and acidic pH properties. The developed composite wound dressing consisted of carboxymethylcellulose(CMC) fibre and also it was reinforced with polylactic acid( PLA) fibre. The produced composite wound dressings were treated with two different CBs at 4% by using the spray method. The details of the CBs have not been disclosed in this paper due to the Intellectual Property Rights( IPR) issues. The important benefit of using CB treatment is that it allows the maintenance of an acidic pH environment at the wound area. It is well known that acidic pH reduces the wound healing time and enhances the wound healing process. Furthermore,one of the CBs not only promotes the proliferation of the epithelial cells in wounds but also can provide antibacterial action. The PLA fibre reinforced CMC composite dressing has enhanced wicking properties which help to minimise the pooling of exudate on the wound bed and as a result maceration is prevented. The CBs treated dressings maintain the wound bed in an acidic pH condition which also improves the wound healing process. In addition to the above-mentioned properties,the CB treatment imparts antimicrobial activity against Gram-positive and Gram-negative bacteria,thus resulting in the reduction in the propensity for wound infection. Ultimately,the research has proved that the 4% CB treatment enhances the antimicrobial activity and the acidic pH characteristics of the developed CMC /PLA composite wound dressings.
