Today,a well-devised charging operation scheme is urgently needed by on-site workmen and is critical for building an intelligent blast furnace(BF).Previous research on charging operations always focused on the two-dim...Today,a well-devised charging operation scheme is urgently needed by on-site workmen and is critical for building an intelligent blast furnace(BF).Previous research on charging operations always focused on the two-dimensional shape of the burden surface(i.e.,a single radial profile)while neglecting the unique feature of global dissymmetry,severely restricting the development of precise charging.For this reason,this study proposes an innovative optimization strategy for the charging operation under the three-dimensional burden surface,which is the first attempt in this field.First,a practicable region partitioning scheme is introduced,and the partitioning results are then integrated with the charging mechanism to construct a three-dimensional burden surface prediction model.Next,the intrinsic relationship between the operational parameters and charging volume is revealed based on the law of mass conservation,which forms the basis for defining a novel operational parameter with variable-speed utility,referred to as the neotype charging matrix(NCM).To find the best NCM,a customized NCM optimization strategy,involving a dual constraint handling technique in conjunction with a two-stage hybrid variable differential evolution algorithm,is further developed.The industrial experiment results manifest that the partitioning scheme significantly enhances the accuracy of burden surface description.Moreover,the NCM optimization strategy offers greater flexibility and higher accuracy than current mainstream optimization strategies for the charging matrix(CM).展开更多
Based on the observed 2-year temperature data for four kinds of typical urban underlying surfaces,including asphalt, cement, bare land and grass land, the annual variations and influencing factors of landsurface tempe...Based on the observed 2-year temperature data for four kinds of typical urban underlying surfaces,including asphalt, cement, bare land and grass land, the annual variations and influencing factors of landsurface temperature are analyzed. Then fitting equations for surface temperature are established. It is shownthat the annual variation of daily average, maximum and minimum temperature and daily temperature rangeon the four urban underlying surfaces is consistent with the change in air temperature. The difference oftemperature on different underlying surfaces in the summer half year (May to October) is much moreevident than that in the winter half year (December to the following April). The daily average and maximumtemperatures of asphalt, cement, bare land and grass land are higher than air temperature due to theatmospheric heating in the daytime, with that of asphalt being the highest, followed in turn by cement, bareland and grass land. Moreover, the daily average, maximum and minimum temperature on the four urbanunderlying surfaces are strongly impacted by total cloud amount, daily average relative humidity andsunshine hours. The land surface can be cooled (warmed) by increased total cloud amount (relativehumidity). The changes in temperature on bare land and grass land are influenced by both the total cloudamount and the daily average relative humidity. The temperature parameters of the four land surfaces aresignificantly correlated with daily average, maximum and minimum temperature, sunshine hours, dailyaverage relative humidity and total cloud amount, respectively. The analysis also indicates that the range offitting parameter of a linear regression equation between the surface temperature of the four kinds of typicalland surface and the air temperature is from 0.809 to 0.971, passing the F-test with a confidence level of 0.99.展开更多
The height anomaly surface is fitt and the quasi-geoid can be obtained when the height anomaly is determined with the geometric analytic method. Therefore, some mathematical models to fit height anomaly surface using ...The height anomaly surface is fitt and the quasi-geoid can be obtained when the height anomaly is determined with the geometric analytic method. Therefore, some mathematical models to fit height anomaly surface using GPS, leveling and terrain data in a local area, including the polynomial fitting model, the multi-surface function fitting model, the motion surface fitting model and the fitting model of little flexibility deformation of thin board, are given. Then the digital characteristics are analyzed with the curved surface theory. The General curvature and the mean curvature of surface are concluded. The advantage, disadvantage and application of the above models are discussed. The effect of terrain undulation on height anomaly is considered in the surface fitting models. The practical case indicates that these models are of validity and practicability. It is concluded that the above models can give the good fitting results at the centimeter level. But the polynomial fitting model is worse than the other models.展开更多
Based on the assumption of the plain-strain problem, various optimization or random search methods have been developed for locating the critical slip surfaces in slope-stability analysis, but none of such methods is a...Based on the assumption of the plain-strain problem, various optimization or random search methods have been developed for locating the critical slip surfaces in slope-stability analysis, but none of such methods is applicable to the 3D case. In this paper, a simple Monte Carlo random simulation method is proposed to identify the 3D critical slip surface. Assuming the initial slip to be the lower part of a slip ellipsoid, the 3D critical slip surface is located by means of a minimized 3D safety factor. A column-based 3D slope stability analysis model is used to calculate this factor. In this study, some practical cases of known minimum safety factors and critical slip surfaces in 2D analysis are extended to 3D slope problems to locate the critical slip surfaces. Compared with the 2D result, the resulting 3D critical slip surface has no apparent difference in terms of only cross section, but the associated 3D safety factor is definitely higher.展开更多
The motion of gas bubbles beneath a free surface will lead to a spike of fluid on the free surface. The distance of the bubbles to the free surface is the key factor to different phenomena. When the inception distance...The motion of gas bubbles beneath a free surface will lead to a spike of fluid on the free surface. The distance of the bubbles to the free surface is the key factor to different phenomena. When the inception distance varies in some range, crown phenomenon would happen after the impact of weak buoyancy bubbles, so this kind of spike is defined as crown spike in the present paper. Based on potential flow theory, a three-dimensional numerical model is established to simulate the motion of the free-surface spike generated by one bubble or a horizontal line of two in-phase bubbles. After the downward jet formed near the end of the collapse phase, the simulation of the free surface is performed to study the crown spike without regard to the toroidal bubble＇s effect. Calculations about the interaction between one bubble and free surface agree well with the experimental results conducted with a high-speed camera, and relative error is within 15%. Crown spike in both single- and two-bubble cases are simulated numerically. Different features and laws of the motion of crown spike, depending on the bubble-boundary distances and the inter-bubble distances, have been investigated.展开更多
A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream su...A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream surface(curved surface)strip elements along metal flow traces,and the stream surface strip elements were mapped into the corresponding plane strip elements for analysis and computation.The longitudinal distributions of the lateral displacement and the altitudinal displacement of metal were respectively constructed to be a quartic curve and a quadratic curve,of which the lateral distributions were expressed as the third-power spline function,and the altitudinal distributions were fitted in the quadratic curve.From the flow theory of plastic mechanics,the mathematical models of the three-dimensional deformations and stresses of the deformation zone were constructed.Compared with the streamline strip element method proposed by the first author of this paper,the stream surface strip element method takes into account the uneven distributions of stresses and deformations along altitudinal direction,and realizes the precise three-dimensional analysis and computation.The simulation example of continuous hot rolled strip indicates that the method and the model accord with facts and provide a new reliable engineering-computation method for the three-dimensional mechanics simulation of plate and strip rolling process.展开更多
The present study elaborates three-dimensional flow of Williamson nanoliquid over a nonlinear stretchable surface. Fluid flow obeys Darcy–Forchheimer porous medium. A bidirectional nonlinear stretching surface genera...The present study elaborates three-dimensional flow of Williamson nanoliquid over a nonlinear stretchable surface. Fluid flow obeys Darcy–Forchheimer porous medium. A bidirectional nonlinear stretching surface generates the flow. Convective surface condition of heat transfer is taken into consideration. Further the zero nanoparticles mass flux condition is imposed at the boundary. Effects of thermophoresis and Brownian diffusion are considered. Assumption of boundary layer has been employed in the problem formulation. Convergent series solutions for the nonlinear governing system are established through the optimal homotopy analysis method(OHAM). Graphs have been sketched in order to analyze that how the velocity, temperature and concentration distributions are affected by distinct emerging flow parameters. Skin friction coefficients and local Nusselt number are also computed and discussed.展开更多
The biomechanical changes during functional loading and unloading of the human gastrointestinal （GI） tract are not fully understood. GI function is usually studled by introducing probes in the GI lumen. Computer mod...The biomechanical changes during functional loading and unloading of the human gastrointestinal （GI） tract are not fully understood. GI function is usually studled by introducing probes in the GI lumen. Computer modeling offers a promising alternative approach in this regard, with the additional ability to predict regional stresses and strains in inaccessible locations. The tension and stress distributions in the GI tract are related to distensibility （tension-strain relationship） and smooth muscle tone. lore knowledge on the tension and stress on the GI tract are needed to improve diagnosis of patients with gastrointestinal disorders. A modeling framework that can be used to integrate the physiological, anatomical and medical knowledge of the GI system has recently been developed. The 3-D anatomical model was constructed from digital images using ultrasonography, computer tomography （CT） or magnetic resonance imaging （IRI）. Different mathematical algorithms were developed for surface analysis based on thin-walled structure and the finite element method was applied for the mucosa-folded three layered esophageal model analysis. The tools may be useful for studying the geometry and biomechanical properties of these organs in health and disease. These studies will serve to test the structurefunction hypothesis of geometrically complex organs.展开更多
Morphology of hydraulic fracture surface has significant effects on oil and gas flow,proppant migration and fracture closure,which plays an important role in oil and gas fracturing stimulation.In this paper,we analyze...Morphology of hydraulic fracture surface has significant effects on oil and gas flow,proppant migration and fracture closure,which plays an important role in oil and gas fracturing stimulation.In this paper,we analyzed the fracture surface characteristics induced by supercritical carbon dioxide(SC-CO_(2))and water in open-hole and perforation completion conditions under triaxial stresses.A simple calculation method was proposed to quantitatively analyze the fracture surface area and roughness in macro-level based on three-dimensional(3D)scanning data.In micro-level,scanning electron micrograph(SEM)was used to analyze the features of fracture surface.The results showed that the surface area of the induced fracture increases with perforation angle for both SC-CO_(2)and water fracturing,and the surface area of SC-CO_(2)-induced fracture is 6.49%e58.57%larger than that of water-induced fracture.The fractal dimension and surface roughness of water-induced fractures increase with the increase in perforation angle,while those of SC-CO_(2)-induced fractures decrease with the increasing perforation angle.A considerable number of microcracks and particle peeling pits can be observed on SC-CO_(2)-induced fracture surface while there are more flat particle surfaces in water-induced fracture surface through SEM images,indicating that fractures tend to propagate along the boundary of the particle for SC-CO_(2)fracturing while water-induced fractures prefer to cut through particles.These findings are of great significance for analyzing fracture mechanism and evaluating fracturing stimulation performance.展开更多
The field spectroradiometer was used to measure spectra of different snow and snow-covered land surface objects in Beijing area.The result showed that for a pure snow spectrum,the snow reflectance peaks appeared from ...The field spectroradiometer was used to measure spectra of different snow and snow-covered land surface objects in Beijing area.The result showed that for a pure snow spectrum,the snow reflectance peaks appeared from visible to 800 nm band locations;there was an obvious absorption valley of snow spectrum near 1 030 nm wavelength.Compared with fresh snow,the reflection peaks of the old snow and melting snow showed different degrees of decline in the ranges of 300～1 300,1 700～1 800 and 2 200～2 300 nm,the lowest was from the compacted snow and frozen ice.For the vegetation and snow mixed spectral characteristics,it was indicated that the spectral reflectance increased for the snow-covered land types(including pine leaf with snow and pine leaf on snow background), due to the influence of snow background in the range of 350～1 300 nm.However, the spectrum reflectance of mixed pixel remained a vegetation spectral characteristic.In the end,based on the spectrum analysis of snow,vegetation,and mixed snow/vegetation pixels,the mixed spectral fitting equations were established,and the results showed that there was good correlation between spectral curves by simulation fitting and observed ones(correlation coefficient R2=0.950 9).展开更多
A three-dimensional conjugate tooth surface design method for Harmonic Drive with a double-circular-arc tooth profle is proposed. The radial deformation function of the fexspline (FS), obtained through Finite Element ...A three-dimensional conjugate tooth surface design method for Harmonic Drive with a double-circular-arc tooth profle is proposed. The radial deformation function of the fexspline (FS), obtained through Finite Element (FE) analysis, is incorporated into the kinematics model. By analyzing the FS tooth enveloping process, the optimization of the overlapping conjugate tooth profle is achieved. By utilizing the hobbing process, the three-dimensional machinable tooth surface of FS can be acquired. Utilizing the coning deformation of the FS, simulations are conducted to analyze the multi-section assembly and meshing motion of the machinable tooth surface. The FE method is utilized to analyze and compare the loaded contact characteristics. Results demonstrate that the proposed design method can achieve an internal gear pair consisting of a circular spline with a spur gear tooth surface and the FS with a machinable tooth surface. With the rated torque, approximately 24% of the FS teeth are engaged in meshing, and more than 4/5 of the tooth surface in the axial direction carries the load. The contact patterns, maximum contact pressure, and transmission error of the machinable tooth surface are 227.2%, 40.67%, and 71.24% of those on the spur gear tooth surface, respectively. It clearly demonstrates exceptional transmission performance.展开更多
Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal...Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal mechanisms(MRMs)involved in the machining of PRMMCs.This paper develops a three-dimensional(3D)microstructure-based model for investigating the MRM and surface integrity of machined PRMMCs.To accurately mimic the actual microstructure of a PRMMC,polyhedrons were randomly distributed inside the matrix to represent irregular SiC particles.Particle fracture and matrix deformation and failure were taken into account.For the model’s capability comparison,a two-dimensional(2D)analysis was also conducted.Relevant cutting experiments showed that the established 3D model accurately predicted the material removal,chip morphology,machined surface finish,and cutting forces.It was found that the matrix-particle-tool interactions led to particle fractures,mainly in the primary shear and secondary deformation zones along the cutting path and beneath the machined surface.Particle fracture and dilodegment greatly influences the quality of a machined surface.It was also found that although a 2D model can reflect certain material removal features,its ability to predict microstructural variation is limited.展开更多
Fitting C2-continuous or superior surfaces to a set S of points sampled on a 2-manifold is central to reverse engineering, computer aided geometric modeling, entertaining, modeling of art heritage, etc. This article a...Fitting C2-continuous or superior surfaces to a set S of points sampled on a 2-manifold is central to reverse engineering, computer aided geometric modeling, entertaining, modeling of art heritage, etc. This article addresses the fitting of analytic (ellipsoid, cones, cylinders) surfaces in general position in . Currently, the state of the art presents limitations in 1) automatically finding an initial guess for the analytic surface F sought, and 2) economically estimating the geometric distance between a point of S and the analytic surface F. These issues are central in estimating an analytic surface which minimizes its accumulated distances to the point set. In response to this situation, this article presents and tests novel user-independent strategies for addressing aspects 1) and 2) above, for cylinders, cones and ellipsoids. A conjecture for the calculation of the distance point-ellipsoid is also proposed. Our strategies produce good initial guesses for F and fast fitting error estimation for F, leading to an agile and robust optimization algorithm. Ongoing work addresses the fitting of free-form parametric surfaces to S.展开更多
AIM To evaluate usefulness of single photon emission computed tomography(SPECT) with three-dimensional stereotactic surface projection(3D-SSP) in distinguishing between Alzheimer's disease(AD) and depression.METHO...AIM To evaluate usefulness of single photon emission computed tomography(SPECT) with three-dimensional stereotactic surface projection(3D-SSP) in distinguishing between Alzheimer's disease(AD) and depression.METHODS We studied 43 patients who presented with both depressive symptoms and memory disturbance. Each subject was evaluated using the following:(1) the Minimal Mental State Examination;(2) the Hamilton Rating Scale for Depression;(3) Clinical Global Impression-Severity scale(CGI-S); and(4) SPECT imaging with 3D-SSP.RESULTS The MMSE scores correlated significantly with the maximum Z-scores of AD-associated regions. CGI-S scores correlated significantly with the maximum Z-scores of depression-associated regions. Factor analysis identified three significant factors. Of these, Factor 1 could be interpreted as favouring a tendency for AD, Factor 2 as favouring a tendency for pseudo-dementia, and Factor 3 as favouring a depressive tendency.CONCLUSION We investigated whether these patients could be categorized as types: Type A(true AD), Type B(pseudodementia), Type C(occult AD), and Type D(true depression). The factor scores in factor analysis supported the validity of this classification. Our results suggest that SPECT with 3D-SSP is highly useful for distinguishing between depression and depressed mood in the early stage of AD.展开更多
A new lens calibration method which is suitable for all kinds of cameras is presented. Based on the global and local adjustable feature of B-spline surface, this method does not require the determination of distortion...A new lens calibration method which is suitable for all kinds of cameras is presented. Based on the global and local adjustable feature of B-spline surface, this method does not require the determination of distortion model of the camera lens. By applying B-spline surface fitting, all kinds of lens distortion models can be simulated. The control points of B-spline surface are estimated inversly from the feature points of detected lines. Then by moving the control points, straight line features in the image can be retrieved. Compared with traditional calibration method, this method has its unique advantage that need no corresponding points between image and scene. Experimental results show the effectiveness of the method.展开更多
A three-dimensional （3-D） approach based on the state space method is proposed to study size-dependent mechanical properties of ultra-thin plate-like elastic structures considering surface effects. The structure is ...A three-dimensional （3-D） approach based on the state space method is proposed to study size-dependent mechanical properties of ultra-thin plate-like elastic structures considering surface effects. The structure is modeled as a laminate composed of a bulk bounded with upper and bottom surface layers, which are allowed to have different material properties from the bulk layer. State equations, including the surface properties of the structure, can be established on the basis of 3-D fundamental elasticity to analyze the size-dependent static characteristics of the thin plate-like structure. Compared with two-dimensional plate theories based size-dependent models for thin film structures in literature, the present 3-D approach is exact, which can provide benchmark results to assess the accuracy of 2-D plate theories and various numerical approaches. To show the feasibility of the proposed approach, a 3-D analytical solution for a simply supported plate-like thin structure including surface layers is derived. An algorithm is proposed for the calculation of the state equations obtained to ensure that the numerical results can reveal the surface effects clearly even for extremely thin surface layers. Numerical examples are carried out to exhibit the surface effects and some discussions are provided based on the results obtained.展开更多
Objective This study optimizes three-dimensional(3D) culture conditions of HepG2 using response surface methodology(RSM) based on the VitroGel system to facilitate the cell model in vitro for liver tissues.Method HepG...Objective This study optimizes three-dimensional(3D) culture conditions of HepG2 using response surface methodology(RSM) based on the VitroGel system to facilitate the cell model in vitro for liver tissues.Method HepG2 cell was 3D cultured on the VitroGel system.Cell viability was detected using Cell Counting Kit-8(CCK-8) assay of HepG2 lived cell numbers.The proliferation of HepG2 cell and clustering performance was measured via fluorescence staining test.Albumin concentration in the culture medium supernatant as an index of HepG2 cell biological function was measured with ELISA kit.Independent factor tests were conducted with three key factors:inoculated cell concentration,cultured time,and dilution degree of the hydrogel.The preliminary results of independent factor tests were used to determine the levels of factors for RSM.Result The selected optimal culture conditions are as follows:concentration of inoculated cells was4.44 × 10^(5)/mL,culture time was 4.86 days,and hydrogel dilution degree was 1:2.23.The result shows that under optimal conditions,the predicted optical density(OD) value of cell viability was 3.10 and measured 2.978 with a relative error of 3.94%.Conclusion This study serves as a reference for the 3D HepG2 culture and constructs liver tissues in vitro.Additionally,it provides the foundation for repeated dose high-throughput toxicity studies and other scientific research work.展开更多
In order to accurately measure an object’s three-dimensional surface shape,the influence of sampling on it was studied.First,on the basis of deriving spectra expressions through the Fourier transform,the generation o...In order to accurately measure an object’s three-dimensional surface shape,the influence of sampling on it was studied.First,on the basis of deriving spectra expressions through the Fourier transform,the generation of CCD pixels was analyzed,and its expression was given.Then,based on the discrete expression of deformation fringes obtained after sampling,its Fourier spectrum expression was derived,resulting in an infinitely repeated"spectra island"in the frequency domain.Finally,on the basis of using a low-pass filter to remove high-order harmonic components and retaining only one fundamental frequency component,the inverse Fourier transform was used to reconstruct the signal strength.A method of reducing the sampling interval,i.e.,reducing the number of sampling points per fringe,was proposed to increase the ratio between the sampling frequency and the fundamental frequency of the grating.This was done to reconstruct the object’s surface shape more accurately under the condition of m>4.The basic principle was verified through simulation and experiment.In the simulation,the sampling intervals were 8 pixels,4 pixels,2 pixels,and 1 pixel,the maximum absolute error values obtained in the last three situations were 88.80%,38.38%,and 31.50%in the first situation,respectively,and the corresponding average absolute error values are 71.84%,43.27%,and 32.26%.It is demonstrated that the smaller the sampling interval,the better the recovery effect.Taking the same four sampling intervals in the experiment as in the simulation can also lead to the same conclusions.The simulated and experimental results show that reducing the sampling interval can improve the accuracy of object surface shape measurement and achieve better reconstruction results.展开更多
To investigate the methodology and evaluate the clinical value of surface mode on three- dimensional ultrasonography (3DUS) in static anatomical structures, 62 patients with various diseases were studied. The equipmen...To investigate the methodology and evaluate the clinical value of surface mode on three- dimensional ultrasonography (3DUS) in static anatomical structures, 62 patients with various diseases were studied. The equipment used here was Voluson 530D 3DUS imaging system and 3D volume trahsducer with frequency being 3. 0-5. 0 MHz. The 3DUS rendering method was surface mode. The results showed that: 1 ) Surface mode of 3DUS could demonstrate clearly the anatomical characteristics of the region-of-interest (ROI) and the inner wall of lesions or organs that contained fluid. The anatomic details, such as location, size, shape, and number of the ROI, could be visualized intuitively; 2) The outer anatomic features (e. g. contour, edge, configuration, etc. ) of some organs or lesions surrounded by fluid could be displayed clearly. It could be concluded that surface mode on 3DUS could provide more diagnostic information than two-dimensional ultrasonography (2DUS) in some cases and could served as a beneficial supplement to ZDUS in clinical practice.展开更多
A new physical structure of vortical flow, i.e., tubular limiting stream surface(TLSS), is reported. It is defined as a general mathematical structure for the physical flow field in the neighborhood of a singularity, ...A new physical structure of vortical flow, i.e., tubular limiting stream surface(TLSS), is reported. It is defined as a general mathematical structure for the physical flow field in the neighborhood of a singularity, and has a close relationship with limit cycles.The TLSS is a tornado-like structure, which separates a vortex into two regions, i.e., the inner region near the vortex axis and the outer region further away from the vortex axis.The flow particles in these two regions can approach to(or leave) the TLSS, but never could reach it.展开更多
基金supported in part by the Science and Technology Innovation Program of Hunan Province(2024RC1007)the Young Scientists Fund of the National Natural Science Foundation of China(62303491)+2 种基金the Major Program of Xiangjiang Laboratory(22XJ01005)the Young Scientists Fund of the National Natural Science Foundation of China(62203473)Central South University Post-Graduate Independent Exploration and Innovation Project(2024ZZTS0451).
文摘Today,a well-devised charging operation scheme is urgently needed by on-site workmen and is critical for building an intelligent blast furnace(BF).Previous research on charging operations always focused on the two-dimensional shape of the burden surface(i.e.,a single radial profile)while neglecting the unique feature of global dissymmetry,severely restricting the development of precise charging.For this reason,this study proposes an innovative optimization strategy for the charging operation under the three-dimensional burden surface,which is the first attempt in this field.First,a practicable region partitioning scheme is introduced,and the partitioning results are then integrated with the charging mechanism to construct a three-dimensional burden surface prediction model.Next,the intrinsic relationship between the operational parameters and charging volume is revealed based on the law of mass conservation,which forms the basis for defining a novel operational parameter with variable-speed utility,referred to as the neotype charging matrix(NCM).To find the best NCM,a customized NCM optimization strategy,involving a dual constraint handling technique in conjunction with a two-stage hybrid variable differential evolution algorithm,is further developed.The industrial experiment results manifest that the partitioning scheme significantly enhances the accuracy of burden surface description.Moreover,the NCM optimization strategy offers greater flexibility and higher accuracy than current mainstream optimization strategies for the charging matrix(CM).
基金Model of Dynamic Monitoring of Drought Evaluation Method and Business System(CMATG2009MS22)
文摘Based on the observed 2-year temperature data for four kinds of typical urban underlying surfaces,including asphalt, cement, bare land and grass land, the annual variations and influencing factors of landsurface temperature are analyzed. Then fitting equations for surface temperature are established. It is shownthat the annual variation of daily average, maximum and minimum temperature and daily temperature rangeon the four urban underlying surfaces is consistent with the change in air temperature. The difference oftemperature on different underlying surfaces in the summer half year (May to October) is much moreevident than that in the winter half year (December to the following April). The daily average and maximumtemperatures of asphalt, cement, bare land and grass land are higher than air temperature due to theatmospheric heating in the daytime, with that of asphalt being the highest, followed in turn by cement, bareland and grass land. Moreover, the daily average, maximum and minimum temperature on the four urbanunderlying surfaces are strongly impacted by total cloud amount, daily average relative humidity andsunshine hours. The land surface can be cooled (warmed) by increased total cloud amount (relativehumidity). The changes in temperature on bare land and grass land are influenced by both the total cloudamount and the daily average relative humidity. The temperature parameters of the four land surfaces aresignificantly correlated with daily average, maximum and minimum temperature, sunshine hours, dailyaverage relative humidity and total cloud amount, respectively. The analysis also indicates that the range offitting parameter of a linear regression equation between the surface temperature of the four kinds of typicalland surface and the air temperature is from 0.809 to 0.971, passing the F-test with a confidence level of 0.99.
基金Project (02 -09 -13) supported by Open Research Fund Programof the Key Laboratory of Geospace Environment and Geodesy , Ministryof Education ,China Project (SD2003 -4) supported by Open Research Fund Programof the Key Laboratory of Geomatice Digital Tech-nology ,Shandong Province , China Project supported by FIG Foundation
文摘The height anomaly surface is fitt and the quasi-geoid can be obtained when the height anomaly is determined with the geometric analytic method. Therefore, some mathematical models to fit height anomaly surface using GPS, leveling and terrain data in a local area, including the polynomial fitting model, the multi-surface function fitting model, the motion surface fitting model and the fitting model of little flexibility deformation of thin board, are given. Then the digital characteristics are analyzed with the curved surface theory. The General curvature and the mean curvature of surface are concluded. The advantage, disadvantage and application of the above models are discussed. The effect of terrain undulation on height anomaly is considered in the surface fitting models. The practical case indicates that these models are of validity and practicability. It is concluded that the above models can give the good fitting results at the centimeter level. But the polynomial fitting model is worse than the other models.
文摘Based on the assumption of the plain-strain problem, various optimization or random search methods have been developed for locating the critical slip surfaces in slope-stability analysis, but none of such methods is applicable to the 3D case. In this paper, a simple Monte Carlo random simulation method is proposed to identify the 3D critical slip surface. Assuming the initial slip to be the lower part of a slip ellipsoid, the 3D critical slip surface is located by means of a minimized 3D safety factor. A column-based 3D slope stability analysis model is used to calculate this factor. In this study, some practical cases of known minimum safety factors and critical slip surfaces in 2D analysis are extended to 3D slope problems to locate the critical slip surfaces. Compared with the 2D result, the resulting 3D critical slip surface has no apparent difference in terms of only cross section, but the associated 3D safety factor is definitely higher.
基金Project supported by the Major Basic Research Project of National Security of China(Grant No.613157)the Excellent Young Scientists Fund of China(Grant No.51222904)
文摘The motion of gas bubbles beneath a free surface will lead to a spike of fluid on the free surface. The distance of the bubbles to the free surface is the key factor to different phenomena. When the inception distance varies in some range, crown phenomenon would happen after the impact of weak buoyancy bubbles, so this kind of spike is defined as crown spike in the present paper. Based on potential flow theory, a three-dimensional numerical model is established to simulate the motion of the free-surface spike generated by one bubble or a horizontal line of two in-phase bubbles. After the downward jet formed near the end of the collapse phase, the simulation of the free surface is performed to study the crown spike without regard to the toroidal bubble＇s effect. Calculations about the interaction between one bubble and free surface agree well with the experimental results conducted with a high-speed camera, and relative error is within 15%. Crown spike in both single- and two-bubble cases are simulated numerically. Different features and laws of the motion of crown spike, depending on the bubble-boundary distances and the inter-bubble distances, have been investigated.
基金Sponsored by National Natural Science Foundation of China(50175095)Provincial Natural Science Foundation of Hebei of China(502173)
文摘A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream surface(curved surface)strip elements along metal flow traces,and the stream surface strip elements were mapped into the corresponding plane strip elements for analysis and computation.The longitudinal distributions of the lateral displacement and the altitudinal displacement of metal were respectively constructed to be a quartic curve and a quadratic curve,of which the lateral distributions were expressed as the third-power spline function,and the altitudinal distributions were fitted in the quadratic curve.From the flow theory of plastic mechanics,the mathematical models of the three-dimensional deformations and stresses of the deformation zone were constructed.Compared with the streamline strip element method proposed by the first author of this paper,the stream surface strip element method takes into account the uneven distributions of stresses and deformations along altitudinal direction,and realizes the precise three-dimensional analysis and computation.The simulation example of continuous hot rolled strip indicates that the method and the model accord with facts and provide a new reliable engineering-computation method for the three-dimensional mechanics simulation of plate and strip rolling process.
文摘The present study elaborates three-dimensional flow of Williamson nanoliquid over a nonlinear stretchable surface. Fluid flow obeys Darcy–Forchheimer porous medium. A bidirectional nonlinear stretching surface generates the flow. Convective surface condition of heat transfer is taken into consideration. Further the zero nanoparticles mass flux condition is imposed at the boundary. Effects of thermophoresis and Brownian diffusion are considered. Assumption of boundary layer has been employed in the problem formulation. Convergent series solutions for the nonlinear governing system are established through the optimal homotopy analysis method(OHAM). Graphs have been sketched in order to analyze that how the velocity, temperature and concentration distributions are affected by distinct emerging flow parameters. Skin friction coefficients and local Nusselt number are also computed and discussed.
文摘The biomechanical changes during functional loading and unloading of the human gastrointestinal （GI） tract are not fully understood. GI function is usually studled by introducing probes in the GI lumen. Computer modeling offers a promising alternative approach in this regard, with the additional ability to predict regional stresses and strains in inaccessible locations. The tension and stress distributions in the GI tract are related to distensibility （tension-strain relationship） and smooth muscle tone. lore knowledge on the tension and stress on the GI tract are needed to improve diagnosis of patients with gastrointestinal disorders. A modeling framework that can be used to integrate the physiological, anatomical and medical knowledge of the GI system has recently been developed. The 3-D anatomical model was constructed from digital images using ultrasonography, computer tomography （CT） or magnetic resonance imaging （IRI）. Different mathematical algorithms were developed for surface analysis based on thin-walled structure and the finite element method was applied for the mucosa-folded three layered esophageal model analysis. The tools may be useful for studying the geometry and biomechanical properties of these organs in health and disease. These studies will serve to test the structurefunction hypothesis of geometrically complex organs.
基金National Natural Science Foundation of China(Grant No.51804318)the China Postdoctoral Science Foundation Founded Project(Grant No.2019M650963)National Key Basic Research and Development Program of China(Grant No.2014CB239203).
文摘Morphology of hydraulic fracture surface has significant effects on oil and gas flow,proppant migration and fracture closure,which plays an important role in oil and gas fracturing stimulation.In this paper,we analyzed the fracture surface characteristics induced by supercritical carbon dioxide(SC-CO_(2))and water in open-hole and perforation completion conditions under triaxial stresses.A simple calculation method was proposed to quantitatively analyze the fracture surface area and roughness in macro-level based on three-dimensional(3D)scanning data.In micro-level,scanning electron micrograph(SEM)was used to analyze the features of fracture surface.The results showed that the surface area of the induced fracture increases with perforation angle for both SC-CO_(2)and water fracturing,and the surface area of SC-CO_(2)-induced fracture is 6.49%e58.57%larger than that of water-induced fracture.The fractal dimension and surface roughness of water-induced fractures increase with the increase in perforation angle,while those of SC-CO_(2)-induced fractures decrease with the increasing perforation angle.A considerable number of microcracks and particle peeling pits can be observed on SC-CO_(2)-induced fracture surface while there are more flat particle surfaces in water-induced fracture surface through SEM images,indicating that fractures tend to propagate along the boundary of the particle for SC-CO_(2)fracturing while water-induced fractures prefer to cut through particles.These findings are of great significance for analyzing fracture mechanism and evaluating fracturing stimulation performance.
基金National Natural Science Foundation of China(40771147)Global Change Research Projects of Key National Scientific Research Plan(2010CB951302)the Social Commonweal Meteorological Research Project(GYHY201106027)
文摘The field spectroradiometer was used to measure spectra of different snow and snow-covered land surface objects in Beijing area.The result showed that for a pure snow spectrum,the snow reflectance peaks appeared from visible to 800 nm band locations;there was an obvious absorption valley of snow spectrum near 1 030 nm wavelength.Compared with fresh snow,the reflection peaks of the old snow and melting snow showed different degrees of decline in the ranges of 300～1 300,1 700～1 800 and 2 200～2 300 nm,the lowest was from the compacted snow and frozen ice.For the vegetation and snow mixed spectral characteristics,it was indicated that the spectral reflectance increased for the snow-covered land types(including pine leaf with snow and pine leaf on snow background), due to the influence of snow background in the range of 350～1 300 nm.However, the spectrum reflectance of mixed pixel remained a vegetation spectral characteristic.In the end,based on the spectrum analysis of snow,vegetation,and mixed snow/vegetation pixels,the mixed spectral fitting equations were established,and the results showed that there was good correlation between spectral curves by simulation fitting and observed ones(correlation coefficient R2=0.950 9).
基金Supported by Guangdong Provincial Key-Area Research and Development Program(Grant No.2019B090917002).
文摘A three-dimensional conjugate tooth surface design method for Harmonic Drive with a double-circular-arc tooth profle is proposed. The radial deformation function of the fexspline (FS), obtained through Finite Element (FE) analysis, is incorporated into the kinematics model. By analyzing the FS tooth enveloping process, the optimization of the overlapping conjugate tooth profle is achieved. By utilizing the hobbing process, the three-dimensional machinable tooth surface of FS can be acquired. Utilizing the coning deformation of the FS, simulations are conducted to analyze the multi-section assembly and meshing motion of the machinable tooth surface. The FE method is utilized to analyze and compare the loaded contact characteristics. Results demonstrate that the proposed design method can achieve an internal gear pair consisting of a circular spline with a spur gear tooth surface and the FS with a machinable tooth surface. With the rated torque, approximately 24% of the FS teeth are engaged in meshing, and more than 4/5 of the tooth surface in the axial direction carries the load. The contact patterns, maximum contact pressure, and transmission error of the machinable tooth surface are 227.2%, 40.67%, and 71.24% of those on the spur gear tooth surface, respectively. It clearly demonstrates exceptional transmission performance.
文摘Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal mechanisms(MRMs)involved in the machining of PRMMCs.This paper develops a three-dimensional(3D)microstructure-based model for investigating the MRM and surface integrity of machined PRMMCs.To accurately mimic the actual microstructure of a PRMMC,polyhedrons were randomly distributed inside the matrix to represent irregular SiC particles.Particle fracture and matrix deformation and failure were taken into account.For the model’s capability comparison,a two-dimensional(2D)analysis was also conducted.Relevant cutting experiments showed that the established 3D model accurately predicted the material removal,chip morphology,machined surface finish,and cutting forces.It was found that the matrix-particle-tool interactions led to particle fractures,mainly in the primary shear and secondary deformation zones along the cutting path and beneath the machined surface.Particle fracture and dilodegment greatly influences the quality of a machined surface.It was also found that although a 2D model can reflect certain material removal features,its ability to predict microstructural variation is limited.
文摘Fitting C2-continuous or superior surfaces to a set S of points sampled on a 2-manifold is central to reverse engineering, computer aided geometric modeling, entertaining, modeling of art heritage, etc. This article addresses the fitting of analytic (ellipsoid, cones, cylinders) surfaces in general position in . Currently, the state of the art presents limitations in 1) automatically finding an initial guess for the analytic surface F sought, and 2) economically estimating the geometric distance between a point of S and the analytic surface F. These issues are central in estimating an analytic surface which minimizes its accumulated distances to the point set. In response to this situation, this article presents and tests novel user-independent strategies for addressing aspects 1) and 2) above, for cylinders, cones and ellipsoids. A conjecture for the calculation of the distance point-ellipsoid is also proposed. Our strategies produce good initial guesses for F and fast fitting error estimation for F, leading to an agile and robust optimization algorithm. Ongoing work addresses the fitting of free-form parametric surfaces to S.
文摘AIM To evaluate usefulness of single photon emission computed tomography(SPECT) with three-dimensional stereotactic surface projection(3D-SSP) in distinguishing between Alzheimer's disease(AD) and depression.METHODS We studied 43 patients who presented with both depressive symptoms and memory disturbance. Each subject was evaluated using the following:(1) the Minimal Mental State Examination;(2) the Hamilton Rating Scale for Depression;(3) Clinical Global Impression-Severity scale(CGI-S); and(4) SPECT imaging with 3D-SSP.RESULTS The MMSE scores correlated significantly with the maximum Z-scores of AD-associated regions. CGI-S scores correlated significantly with the maximum Z-scores of depression-associated regions. Factor analysis identified three significant factors. Of these, Factor 1 could be interpreted as favouring a tendency for AD, Factor 2 as favouring a tendency for pseudo-dementia, and Factor 3 as favouring a depressive tendency.CONCLUSION We investigated whether these patients could be categorized as types: Type A(true AD), Type B(pseudodementia), Type C(occult AD), and Type D(true depression). The factor scores in factor analysis supported the validity of this classification. Our results suggest that SPECT with 3D-SSP is highly useful for distinguishing between depression and depressed mood in the early stage of AD.
文摘A new lens calibration method which is suitable for all kinds of cameras is presented. Based on the global and local adjustable feature of B-spline surface, this method does not require the determination of distortion model of the camera lens. By applying B-spline surface fitting, all kinds of lens distortion models can be simulated. The control points of B-spline surface are estimated inversly from the feature points of detected lines. Then by moving the control points, straight line features in the image can be retrieved. Compared with traditional calibration method, this method has its unique advantage that need no corresponding points between image and scene. Experimental results show the effectiveness of the method.
基金supported by the Natural Science Foundation of Anhui Province(No.070414190).
文摘A three-dimensional （3-D） approach based on the state space method is proposed to study size-dependent mechanical properties of ultra-thin plate-like elastic structures considering surface effects. The structure is modeled as a laminate composed of a bulk bounded with upper and bottom surface layers, which are allowed to have different material properties from the bulk layer. State equations, including the surface properties of the structure, can be established on the basis of 3-D fundamental elasticity to analyze the size-dependent static characteristics of the thin plate-like structure. Compared with two-dimensional plate theories based size-dependent models for thin film structures in literature, the present 3-D approach is exact, which can provide benchmark results to assess the accuracy of 2-D plate theories and various numerical approaches. To show the feasibility of the proposed approach, a 3-D analytical solution for a simply supported plate-like thin structure including surface layers is derived. An algorithm is proposed for the calculation of the state equations obtained to ensure that the numerical results can reveal the surface effects clearly even for extremely thin surface layers. Numerical examples are carried out to exhibit the surface effects and some discussions are provided based on the results obtained.
基金funded by Toxicity Evaluation of Key Contaminants in Health Food by Cell-based Test Models and the Mechanism Analysis [2018YFC1602104]
文摘Objective This study optimizes three-dimensional(3D) culture conditions of HepG2 using response surface methodology(RSM) based on the VitroGel system to facilitate the cell model in vitro for liver tissues.Method HepG2 cell was 3D cultured on the VitroGel system.Cell viability was detected using Cell Counting Kit-8(CCK-8) assay of HepG2 lived cell numbers.The proliferation of HepG2 cell and clustering performance was measured via fluorescence staining test.Albumin concentration in the culture medium supernatant as an index of HepG2 cell biological function was measured with ELISA kit.Independent factor tests were conducted with three key factors:inoculated cell concentration,cultured time,and dilution degree of the hydrogel.The preliminary results of independent factor tests were used to determine the levels of factors for RSM.Result The selected optimal culture conditions are as follows:concentration of inoculated cells was4.44 × 10^(5)/mL,culture time was 4.86 days,and hydrogel dilution degree was 1:2.23.The result shows that under optimal conditions,the predicted optical density(OD) value of cell viability was 3.10 and measured 2.978 with a relative error of 3.94%.Conclusion This study serves as a reference for the 3D HepG2 culture and constructs liver tissues in vitro.Additionally,it provides the foundation for repeated dose high-throughput toxicity studies and other scientific research work.
文摘In order to accurately measure an object’s three-dimensional surface shape,the influence of sampling on it was studied.First,on the basis of deriving spectra expressions through the Fourier transform,the generation of CCD pixels was analyzed,and its expression was given.Then,based on the discrete expression of deformation fringes obtained after sampling,its Fourier spectrum expression was derived,resulting in an infinitely repeated"spectra island"in the frequency domain.Finally,on the basis of using a low-pass filter to remove high-order harmonic components and retaining only one fundamental frequency component,the inverse Fourier transform was used to reconstruct the signal strength.A method of reducing the sampling interval,i.e.,reducing the number of sampling points per fringe,was proposed to increase the ratio between the sampling frequency and the fundamental frequency of the grating.This was done to reconstruct the object’s surface shape more accurately under the condition of m>4.The basic principle was verified through simulation and experiment.In the simulation,the sampling intervals were 8 pixels,4 pixels,2 pixels,and 1 pixel,the maximum absolute error values obtained in the last three situations were 88.80%,38.38%,and 31.50%in the first situation,respectively,and the corresponding average absolute error values are 71.84%,43.27%,and 32.26%.It is demonstrated that the smaller the sampling interval,the better the recovery effect.Taking the same four sampling intervals in the experiment as in the simulation can also lead to the same conclusions.The simulated and experimental results show that reducing the sampling interval can improve the accuracy of object surface shape measurement and achieve better reconstruction results.
文摘To investigate the methodology and evaluate the clinical value of surface mode on three- dimensional ultrasonography (3DUS) in static anatomical structures, 62 patients with various diseases were studied. The equipment used here was Voluson 530D 3DUS imaging system and 3D volume trahsducer with frequency being 3. 0-5. 0 MHz. The 3DUS rendering method was surface mode. The results showed that: 1 ) Surface mode of 3DUS could demonstrate clearly the anatomical characteristics of the region-of-interest (ROI) and the inner wall of lesions or organs that contained fluid. The anatomic details, such as location, size, shape, and number of the ROI, could be visualized intuitively; 2) The outer anatomic features (e. g. contour, edge, configuration, etc. ) of some organs or lesions surrounded by fluid could be displayed clearly. It could be concluded that surface mode on 3DUS could provide more diagnostic information than two-dimensional ultrasonography (2DUS) in some cases and could served as a beneficial supplement to ZDUS in clinical practice.
基金Project supported by the National Natural Science Foundation of China(Nos.11372340 and 11732016)
文摘A new physical structure of vortical flow, i.e., tubular limiting stream surface(TLSS), is reported. It is defined as a general mathematical structure for the physical flow field in the neighborhood of a singularity, and has a close relationship with limit cycles.The TLSS is a tornado-like structure, which separates a vortex into two regions, i.e., the inner region near the vortex axis and the outer region further away from the vortex axis.The flow particles in these two regions can approach to(or leave) the TLSS, but never could reach it.
