A method of constructing three-dimensional process model for the punching cartridge cases is presented based on DEFORM simulation analysis. Using DEFORM software,the finite element simulation models for the punching a...A method of constructing three-dimensional process model for the punching cartridge cases is presented based on DEFORM simulation analysis. Using DEFORM software,the finite element simulation models for the punching and forming process of cartridge cases are established,and the corresponding simulation result model of each intermediate procedure is obtained by continuously performing the forming process simulation. The simulation model cannot annotate size and process information due to poor interface between DEFORM software and CAD software. Thus,a 3D annotation module is developed with secondary development technology of UG NX software. Consequently,the final process model with dimension and process information is obtained. Then,with the current 3D process management system,the 3D punching and forming process design of cartridge cases can be completed further. An example is also provided to illustrate that the relative error between the simulation process model and the physical model is less than 2%,which proves the validity and reliability of the proposed method in this study.展开更多
Bone repair remains an important target in tissue engineering,making the development of bioactive scaffolds for effective bone defect repair a critical objective.In this study,β-tricalcium phosphate(β-TCP)scaffolds ...Bone repair remains an important target in tissue engineering,making the development of bioactive scaffolds for effective bone defect repair a critical objective.In this study,β-tricalcium phosphate(β-TCP)scaffolds incorporated with processed pyritum decoction(PPD)were fabricated using three-dimensional(3D)printing-assisted freeze-casting.The produced composite scaffolds were evaluated for their mechanical strength,physicochemical properties,biocompatibility,in vitro proangiogenic activity,and in vivo efficacy in repairing rabbit femoral defects.They not only demonstrated excellent physicochemical properties,enhanced mechanical strength,and good biosafety but also significantly promoted the proliferation,migration,and aggregation of pro-angiogenic human umbilical vein endothelial cells(HUVECs).In vivo studies revealed that all scaffold groups facilitated osteogenesis at the bone defect site,with theβ-TCP scaffolds loaded with PPD markedly enhancing the expression of neurogenic locus Notch homolog protein 1(Notch1),vascular endothelial growth factor(VEGF),bone morphogenetic protein-2(BMP-2),and osteopontin(OPN).Overall,the scaffolds developed in this study exhibited strong angiogenic and osteogenic capabilities both in vitro and in vivo.The incorporation of PPD notably promoted the angiogenic-osteogenic coupling,thereby accelerating bone repair,which suggests that PPD is a promising material for bone repair and that the PPD/β-TCP scaffolds hold great potential as a bone graft alternative.展开更多
According to the Mindlin plate theory and the first-order piston theory,this work obtains accurate closed-form eigensolutions for the flutter problem of three-dimensional(3D)rectangular laminated panels.The governing ...According to the Mindlin plate theory and the first-order piston theory,this work obtains accurate closed-form eigensolutions for the flutter problem of three-dimensional(3D)rectangular laminated panels.The governing differential equations are derived by the Hamilton's variational principle,and then solved by the iterative Separation-of-Variable(i SOV)method,which are applicable to arbitrary combinations of homogeneous Boundary Conditions(BCs).However,only the simply-support,clamped and cantilever panels are considered in this work for the sake of clarity.With the closed-form eigensolutions,the flutter frequency,flutter mode and flutter boundary are presented,and the effect of shear deformation and aerodynamic damping on flutter frequencies is investigated.Besides,the relation between panel energy and the work of aerodynamic load is discussed.The numerical comparisons reveal the following.(A)The flutter eigenvalues obtained by the present method are accurate,validated by the Finite Element Method(FEM)and the Galerkin method.(B)When the span-chord ratio is larger than 3,simplifying a 3D panel to 2D(two-dimensional)panel is reasonable and the relative differences of the flutter points predicted by the two models are less than one percent.(C)The reciprocal relationship between the mechanical energy of the panel and the work done by aerodynamic load is verified by using the present flutter eigenvalues and modes,further indicating the high accuracy of the present solutions.(D)The coupling of shear deformation and aerodynamic damping prevents frequency coalescing.展开更多
Three-dimensional(3D)single molecule localization microscopy(SMLM)plays an important role in biomedical applications,but its data processing is very complicated.Deep learning is a potential tool to solve this problem....Three-dimensional(3D)single molecule localization microscopy(SMLM)plays an important role in biomedical applications,but its data processing is very complicated.Deep learning is a potential tool to solve this problem.As the state of art 3D super-resolution localization algorithm based on deep learning,FD-DeepLoc algorithm reported recently still has a gap with the expected goal of online image processing,even though it has greatly improved the data processing throughput.In this paper,a new algorithm Lite-FD-DeepLoc is developed on the basis of FD-DeepLoc algorithm to meet the online image processing requirements of 3D SMLM.This new algorithm uses the feature compression method to reduce the parameters of the model,and combines it with pipeline programming to accelerate the inference process of the deep learning model.The simulated data processing results show that the image processing speed of Lite-FD-DeepLoc is about twice as fast as that of FD-DeepLoc with a slight decrease in localization accuracy,which can realize real-time processing of 256×256 pixels size images.The results of biological experimental data processing imply that Lite-FD-DeepLoc can successfully analyze the data based on astigmatism and saddle point engineering,and the global resolution of the reconstructed image is equivalent to or even better than FD-DeepLoc algorithm.展开更多
Next-generation artificial tactile systems demand seamless integration with neuromorphic architectures to support on-edge computation and high-fidelity sensory signal processing.Despite significant advancements,curren...Next-generation artificial tactile systems demand seamless integration with neuromorphic architectures to support on-edge computation and high-fidelity sensory signal processing.Despite significant advancements,current research remains predominantly focused on optimizing individual sensor elements,and systems utilizing single neuromorphic components encounter inherent limitations in enhancing overall functionality.Here,we present a vertically integrated in-sensor processing platform,which combines a three-dimensional antiferroelectric field-effect transistor(AFEFET)device with an aluminum nitride(AlN)piezoelectric sensor.展开更多
Convectively unstable processes caused by dense water subsidence are common occurrences in high-latitude oceanic regions,and significantly modulate mass and heat transport and mixing processes in the ocean.An idealize...Convectively unstable processes caused by dense water subsidence are common occurrences in high-latitude oceanic regions,and significantly modulate mass and heat transport and mixing processes in the ocean.An idealized numerical experiment using the large eddy simulation method was conducted to analyze the three-dimensional flow field structure and the mechanism for dense water subsidence.Specifically,a negative salt flux is set at the sea surface,in which salt flux enters the sea surface to simulate the icing and salting-out phenomena that occur at high latitudes.Results show that the mean-state 3D flow field of dense water subsidence exhibits a hollow conical distribution.The horizontal flow field is characterized by a cyclonic vortex that driven primarily by the pressure gradient and influenced by the Coriolis effect.Moreover,the inverse vertical pressure gradient generated by this vortex inhibits the sinking of the plume,leading to its off-axis deflection and the development of an anticyclonic precession.In addition,the impact of rotation on the structure of a sinking plume within a stratified environment is discussed.Both horizontal vortex intensity and cone angle of the hollow cone flow field are increased with increasing rotation rate,resulting in a decrease in the plume’s maximum sinking depth.Variances in rotation direction cause the horizontal vortex and sinking plumes of dense water in the northern and southern hemispheres to rotate in opposite directions.展开更多
A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on...A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on the three-dimensional morphology of TiB2 particles.Different preparation routes result in different reaction forms,which accounts for the morphology variation of TiB2 particles.When the Al-Ti-B master alloy is prepared using ＂halide salt＂ route,TiB2 particles exhibit hexagonal platelet morphology and are independent with each other.In addition,the reaction temperature almost does not have influence on the morphology of TiB2 particles.However,TiB2 particles exhibit different morphologies at different reaction temperatures when the master alloys are prepared with Al-3B and Ti sponge.When the master alloy is prepared at 850 ℃,a kind of TiB2 particle agglomeration forms with a size larger than 5 μm.The TiB2 particles change to layered stacking morphology even dendritic morphology with the reaction temperature reaching up to 1200 ℃.展开更多
To study the influence of roll casting process parameters on temperature and thermal-stress fields for the AZ31 magnesium alloy sheets,three-dimensional geometric and 3D finite element models for roll casting were est...To study the influence of roll casting process parameters on temperature and thermal-stress fields for the AZ31 magnesium alloy sheets,three-dimensional geometric and 3D finite element models for roll casting were established based on the symmetry of roll casting by ANSYS software.Meshing method and smart-sizing algorithm were used to divide finite element mesh in ANSYS software.A series of researches on the temperature and stress distributions during solidification process with different process parameters were done by 3D finite element method.The temperatures of both the liquid-solid two-phase zone and liquid phase zone were elevated with increasing pouring temperature.With the heat transfer coefficient increasing,the two-phase region for liquid-solid becomes smaller.With the pouring temperature increasing and the increase of casting speed,the length of two-phase zone rises.The optimized of process parameters（casting speed 2 m/min,pouring temperature 640 ℃ and heat transfer coefficient 15 kW/（m2·℃） with the water pouring at roller exit was used to produce magnesium alloy AZ31 sheet,and equiaxed grains with the average grain size of 50 μm were achieved after roll casting.The simulation results give better understanding of the temperature variation in phase transformation zone and the formation mechanism of hot cracks in plates during roll casting and help to design the optimized process parameters of roll casting for Mg alloy.展开更多
一、作为哲学的AI for Process(一)郭为的哲学思想1.郭为是谁郭为是谁?他是一位哲学家。顺便说,他同时还领导着神州数码。为什么说郭为是哲学家呢?因为他在著作中谈到高深的哲学,如“数据如水,奔流不息,无界融合”。他引述古希腊哲学家...一、作为哲学的AI for Process(一)郭为的哲学思想1.郭为是谁郭为是谁?他是一位哲学家。顺便说,他同时还领导着神州数码。为什么说郭为是哲学家呢?因为他在著作中谈到高深的哲学,如“数据如水,奔流不息,无界融合”。他引述古希腊哲学家赫拉克利特所说的“万物流转”,又说“你不能两次踏进同一条河流,因为新的水不断地流过你的身旁”,他所表达的意思是“世界上唯一不变的就是变化”。展开更多
Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic...Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic FEM code has been developed. Isothermal forging process of a cylindrical housing has been simulated. The simulation results show that the given techniques and the FEM code are reasonable and feasible for three-dimensional bulk forming processes.展开更多
A self-designed setup of modified sloping cooling/shearing process was made to prepare the semisolid Al-3wt%Mg alloy. A three-dimensional simulation model was established for the analysis of preparing the semisolid Al...A self-designed setup of modified sloping cooling/shearing process was made to prepare the semisolid Al-3wt%Mg alloy. A three-dimensional simulation model was established for the analysis of preparing the semisolid Al-3wt%Mg alloy. Through simulation and experiment, it is shown that the sloping angle of the plate greatly affects temperature and velocity distributions, and the temperature and velocity of the alloy at the exit of the sloping plate increase with the increase of the sloping angle. The alloy temperature decreases linearly from the pouring mouth to the exit. The alloy temperature at the exit increases obviously with the increase of pouring temperature. To prepare the semisolid Al-3wt%Mg alloy with good quality, the sloping angle θ=45° is reasonable, and the pouring temperature is suggested to be designed above 650-660℃ but under 700℃.展开更多
To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D lea...To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D leader-following cooperative interception guidance law.First,in the LOS direction of the leader,an impact time-controlled guidance law is derived based on the fixed-time stability theory,which enables the leader to complete the interception task at a prespecified impact time.Next,in the LOS direction of the followers,by introducing a time consensus tracking error function,a fixed-time consensus tracking guidance law is investigated to guarantee the consensus tracking convergence of the time-to-go.Then,in the direction normal to the LOS,by combining the designed global integral sliding mode surface and the second-order Sliding Mode Control(SMC)theory,an innovative 3D LOS-angle-constrained interception guidance law is developed,which eliminates the reaching phase in the traditional sliding mode guidance laws and effectively saves energy consumption.Moreover,it effectively suppresses the chattering phenomenon while avoiding the singularity issue,and compensates for unknown interference caused by target maneuvering online,making it convenient for practical engineering applications.Finally,theoretical proof analysis and multiple sets of numerical simulation results verify the effectiveness,superiority,and robustness of the investigated guidance law.展开更多
Three-dimensional(3D)urban structures play a critical role in informing climate mitigation strategies aimed at the built environment and facilitating sustainable urban development.Regrettably,there exists a significan...Three-dimensional(3D)urban structures play a critical role in informing climate mitigation strategies aimed at the built environment and facilitating sustainable urban development.Regrettably,there exists a significant gap in detailed and consistent data on 3D building space structures with global coverage due to the challenges inherent in the data collection and model calibration processes.In this study,we constructed a global urban structure(GUS-3D)dataset,including building volume,height,and footprint information,at a 500 m spatial resolution using extensive satellite observation products and numerous reference building samples.Our analysis indicated that the total volume of buildings worldwide in2015 exceeded 1×10^(12)m^(3).Over the 1985 to 2015 period,we observed a slight increase in the magnitude of 3D building volume growth(i.e.,it increased from 166.02 km3 during the 1985–2000 period to 175.08km3 during the 2000–2015 period),while the expansion magnitudes of the two-dimensional(2D)building footprint(22.51×10^(3) vs 13.29×10^(3)km^(2))and urban extent(157×10^(3) vs 133.8×10^(3)km^(2))notably decreased.This trend highlights the significant increase in intensive vertical utilization of urban land.Furthermore,we identified significant heterogeneity in building space provision and inequality across cities worldwide.This inequality is particularly pronounced in many populous Asian cities,which has been overlooked in previous studies on economic inequality.The GUS-3D dataset shows great potential to deepen our understanding of the urban environment and creates new horizons for numerous 3D urban studies.展开更多
BACKGROUND Inguinal hernias are common after surgery.Tension-free repair is widely accepted as the main method for managing inguinal hernias.Adequate exposure,coverage,and repair of the myopectineal orifice(MPO)are ne...BACKGROUND Inguinal hernias are common after surgery.Tension-free repair is widely accepted as the main method for managing inguinal hernias.Adequate exposure,coverage,and repair of the myopectineal orifice(MPO)are necessary.However,due to differences in race and sex,people’s body shapes vary.According to European guidelines,the patch should measure 10 cm×15 cm.If any part of the MPO is dissected,injury to the nerves,vascular network,or organs may occur during surgery,thereby leading to inguinal discomfort,pain,and seroma formation after surgery.Therefore,accurate localization and measurement of the boundary of the MPO are crucial for selecting the optimal patch for inguinal hernia repair.AIM To compare the size of the MPO measured on three-dimensional multislice spiral computed tomography(CT)with that measured via laparoscopy and explore the relevant factors influencing the size of the MPO.METHODS Clinical data from 74 patients who underwent laparoscopic tension-free inguinal hernia repair at the General Surgery Department of the First Affiliated Hospital of Anhui University of Science and Technology between September 2022 and July 2024 were collected and analyzed retrospectively.Transabdominal preperitoneal was performed.Sixty-four males and 10 females,with an average age of 58.30±12.32 years,were included.The clinical data of the patients were collected.The boundary of the MPO was measured on three-dimensional CT images before surgery and then again during transabdominal preperitoneal.All the preoperative and intraoperative data were analyzed via paired t-tests.A t-test was used for comparisons of age,body mass index,and sex between the groups.In the comparative analysis,a P value less than 0.05 indicated a significant difference.RESULTS The boundaries of the MPO on 3-dimensional CT images measured 7.05±0.47 cm and 6.27±0.61 cm,and the area of the MPO was 19.54±3.33 cm^(2).The boundaries of the MPO during surgery were 7.18±0.51 cm and 6.17±0.40 cm.The errors were not statistically significant.However,the intraoperative BD(the width of the MPO,P=0.024,P<0.05)and preoperative AC(the length of the MPO,P=0.045,P<0.05)significantly differed according to sex.The AC and BD measurements before and during surgery were not significantly different according to age,body mass index,hernia side or hernia type(P>0.05).CONCLUSION The application of this technology can aid in determining the most appropriate dissection range and patch size.展开更多
The fabrication process dependent effects on single event effects （SEEs） are investigated in a commercial silicon- germanium heterojunction bipolar transistor （SiGe HBT） using three-dimensional （3D） TCAD simulat...The fabrication process dependent effects on single event effects （SEEs） are investigated in a commercial silicon- germanium heterojunction bipolar transistor （SiGe HBT） using three-dimensional （3D） TCAD simulations. The influences of device structure and doping concentration on SEEs are discussed via analysis of current transient and charge collection induced by ions strike. The results show that the SEEs representation of current transient is different from representation of the charge collection for the same process parameters. To be specific, the area of C/S junction is the key parameter that affects charge collection of SEE. Both current transient and charge collection are dependent on the doping of collector and substrate. The base doping slightly influences transient currents of base, emitter, and collector terminals. However, the SEEs of SiGe HBT are hardly affected by the doping of epitaxial base and the content of Ge.展开更多
The traditional fuzzy logic system （FLS） can only model and control the process in two-dimensional nature. Many of real-world systems are of multidimensional features, such as, thermal and fluid processes with spati...The traditional fuzzy logic system （FLS） can only model and control the process in two-dimensional nature. Many of real-world systems are of multidimensional features, such as, thermal and fluid processes with spatiotemporal dynamics, biological systems, or decision-making processes that contain stochastic and imprecise uncertainties. These types of systems are difficult for the traditional FLS to model and control because they require a third dimension for spatial or probabilistic information. The type-2 fuzzy set provides the possibility to develop a three-dimensional fuzzy logic system for modeling and controlling these processes in three-dimensional nature.展开更多
True-triaxial compression tests were carried out on cubic granite samples with a circular through hole using a true-triaxial testing system to investigate the influence of saturated water content(SWC) on the failure p...True-triaxial compression tests were carried out on cubic granite samples with a circular through hole using a true-triaxial testing system to investigate the influence of saturated water content(SWC) on the failure process and characteristics of a circular tunnel of surrounding rocks. The spalling failure under SWC can be divided into four periods: calm period, buckling deformation period, period of rock fragment gradual buckling and exfoliation, and period of formation of symmetrical V-shaped notches. When the horizontal axial and vertical stresses were constant, the spalling failure severity was reduced with the increase in lateral stress. Under natural water content, a strong rockburst with dynamic failure characteristics occurred on the circular hole sidewall. Under SWC, the failure severity was reduced and the circular hole sidewall experienced spalling failure, exhibiting progressive static failure characteristics.Therefore, water can reduce the failure severity of surrounding rocks in deep underground engineering, which has a certain guiding significance for the prevention and control of rockbursts.展开更多
To shorten the preparation process of semi-solid billets,semi-solid billets of 2A14 aluminum alloy were prepared by wrought aluminum directly semi-solid isothermal treatment(WADSSIT)process.Three-dimension(3D)combined...To shorten the preparation process of semi-solid billets,semi-solid billets of 2A14 aluminum alloy were prepared by wrought aluminum directly semi-solid isothermal treatment(WADSSIT)process.Three-dimension(3D)combined microstructure evolution,namely transverse direction(TD)surface,rolling direction(RD)surface,and normal direction(ND)surface,was studied.Effects of temperature and holding time on average grain size and average shape factor were investigated.The results showed that the optimum conditions for preparation of 2A14 semi-solid billets by this process were 615℃ and 20 min(average grain size of 124μm and shape factor of 0.81).Electron backscatter diffraction(EBSD)observations indicated that the microstructure was completely recrystallized when it was heated to 600℃.Grain size was increased with the increase of temperature and grew up slowly with the holding time prolonging.Roundness was increased with increase of holding time but was not sensitive to temperature.展开更多
The extremely high peak intensity associated with ultrashort pulse width of femtosecond(fs)lasers enabled inducing nonlinear multiphoton absorption in materials that are transparent to the laser wavelength.More import...The extremely high peak intensity associated with ultrashort pulse width of femtosecond(fs)lasers enabled inducing nonlinear multiphoton absorption in materials that are transparent to the laser wavelength.More importantly,focusing the fs laser beam inside the transparent materials confined the nonlinear interaction to within the focal volume only,realizing three-dimensional(3D)micro/nanofabrication.This 3D capability offers three different processing schemes for use in fabrication:undeformative,subtractive,and additive.Furthermore,a hybrid approach of different schemes can create much more complex 3D structures and thereby promises to enhance the functionality of the structures created.Thus,hybrid fs laser 3D microprocessing opens a new door for material processing.This paper comprehensively reviews different types of hybrid fs laser 3D micro/nanoprocessing for diverse applications including fabrication of functional micro/nanodevices.展开更多
Air separators provide safe, clean, and appropriate air flow to engines and are widely used in vehicles with large engines such as ships and submarines. In this operational study, the separation process in a Ranque-Hi...Air separators provide safe, clean, and appropriate air flow to engines and are widely used in vehicles with large engines such as ships and submarines. In this operational study, the separation process in a Ranque-Hilsch vortex tube cleaning （cooling） system is investigated to analyze the impact of the operating gas type on the vortex tube performance; the operating gases used are air, nitrogen, oxygen, carbon dioxide and nitrogen dioxide. The computational fluid dynamic model used is equipped with a three-dimensional structure, and the steady-state condition is applied during computations. The standard k-c turbulence model is employed to resolve nonlinear flow equations, and various key parameters, such as hot and cold exhaust thermal drops, and power separation rates, are described numerically. The results show that nitrogen dioxide creates the greatest separation power out of all gases tested, and the numerical results are validated by good agreement with available experimental data. In addition, a comparison is made between the use of two different boundary conditions, the pressure-far-field and the pressure-outlet, when analyzing complex turbulent flows in the air separators. Results present a comprehensive and practical solution for use in future numerical studies.展开更多
基金Supported by the National Defense Basic Scientific Research Project(A1020131011)
文摘A method of constructing three-dimensional process model for the punching cartridge cases is presented based on DEFORM simulation analysis. Using DEFORM software,the finite element simulation models for the punching and forming process of cartridge cases are established,and the corresponding simulation result model of each intermediate procedure is obtained by continuously performing the forming process simulation. The simulation model cannot annotate size and process information due to poor interface between DEFORM software and CAD software. Thus,a 3D annotation module is developed with secondary development technology of UG NX software. Consequently,the final process model with dimension and process information is obtained. Then,with the current 3D process management system,the 3D punching and forming process design of cartridge cases can be completed further. An example is also provided to illustrate that the relative error between the simulation process model and the physical model is less than 2%,which proves the validity and reliability of the proposed method in this study.
基金supported by the National Science Foundation of China(Nos.81373970,81773902,81973484,and 32171402)the National College Students Innovation and Entrepreneurship Training Program(No.201810315019)+4 种基金the Postgraduate Research and Practice Innovation Program of Jiangsu Province(Nos.SJCX21_0712 and KYCX23_2052)the Scientific Research Project of Jiangsu Provincial Association of Traditional Chinese Medicine(No.XYLD2024013)the Youth Scientific Research Project of Jiangyin Municipal Health Commission(No.Q202402)the Natural Science Foundation Project of Nanjing University of Chinese Medicine(No.XZR2024173)the Jiangyin Science and Technology Innovation Special Fund Project(No.JY0603A011014230032PB),China.
文摘Bone repair remains an important target in tissue engineering,making the development of bioactive scaffolds for effective bone defect repair a critical objective.In this study,β-tricalcium phosphate(β-TCP)scaffolds incorporated with processed pyritum decoction(PPD)were fabricated using three-dimensional(3D)printing-assisted freeze-casting.The produced composite scaffolds were evaluated for their mechanical strength,physicochemical properties,biocompatibility,in vitro proangiogenic activity,and in vivo efficacy in repairing rabbit femoral defects.They not only demonstrated excellent physicochemical properties,enhanced mechanical strength,and good biosafety but also significantly promoted the proliferation,migration,and aggregation of pro-angiogenic human umbilical vein endothelial cells(HUVECs).In vivo studies revealed that all scaffold groups facilitated osteogenesis at the bone defect site,with theβ-TCP scaffolds loaded with PPD markedly enhancing the expression of neurogenic locus Notch homolog protein 1(Notch1),vascular endothelial growth factor(VEGF),bone morphogenetic protein-2(BMP-2),and osteopontin(OPN).Overall,the scaffolds developed in this study exhibited strong angiogenic and osteogenic capabilities both in vitro and in vivo.The incorporation of PPD notably promoted the angiogenic-osteogenic coupling,thereby accelerating bone repair,which suggests that PPD is a promising material for bone repair and that the PPD/β-TCP scaffolds hold great potential as a bone graft alternative.
基金support of the National Natural Science Foundation of China(No.12172023)。
文摘According to the Mindlin plate theory and the first-order piston theory,this work obtains accurate closed-form eigensolutions for the flutter problem of three-dimensional(3D)rectangular laminated panels.The governing differential equations are derived by the Hamilton's variational principle,and then solved by the iterative Separation-of-Variable(i SOV)method,which are applicable to arbitrary combinations of homogeneous Boundary Conditions(BCs).However,only the simply-support,clamped and cantilever panels are considered in this work for the sake of clarity.With the closed-form eigensolutions,the flutter frequency,flutter mode and flutter boundary are presented,and the effect of shear deformation and aerodynamic damping on flutter frequencies is investigated.Besides,the relation between panel energy and the work of aerodynamic load is discussed.The numerical comparisons reveal the following.(A)The flutter eigenvalues obtained by the present method are accurate,validated by the Finite Element Method(FEM)and the Galerkin method.(B)When the span-chord ratio is larger than 3,simplifying a 3D panel to 2D(two-dimensional)panel is reasonable and the relative differences of the flutter points predicted by the two models are less than one percent.(C)The reciprocal relationship between the mechanical energy of the panel and the work done by aerodynamic load is verified by using the present flutter eigenvalues and modes,further indicating the high accuracy of the present solutions.(D)The coupling of shear deformation and aerodynamic damping prevents frequency coalescing.
基金supported by the Start-up Fund from Hainan University(No.KYQD(ZR)-20077)。
文摘Three-dimensional(3D)single molecule localization microscopy(SMLM)plays an important role in biomedical applications,but its data processing is very complicated.Deep learning is a potential tool to solve this problem.As the state of art 3D super-resolution localization algorithm based on deep learning,FD-DeepLoc algorithm reported recently still has a gap with the expected goal of online image processing,even though it has greatly improved the data processing throughput.In this paper,a new algorithm Lite-FD-DeepLoc is developed on the basis of FD-DeepLoc algorithm to meet the online image processing requirements of 3D SMLM.This new algorithm uses the feature compression method to reduce the parameters of the model,and combines it with pipeline programming to accelerate the inference process of the deep learning model.The simulated data processing results show that the image processing speed of Lite-FD-DeepLoc is about twice as fast as that of FD-DeepLoc with a slight decrease in localization accuracy,which can realize real-time processing of 256×256 pixels size images.The results of biological experimental data processing imply that Lite-FD-DeepLoc can successfully analyze the data based on astigmatism and saddle point engineering,and the global resolution of the reconstructed image is equivalent to or even better than FD-DeepLoc algorithm.
基金supported by the National Research Foundation of Korea(No.2021R1A2C2095322)supported by Grant Nos.RS-2023-00260527,RS-2023-00231985,RS2023-00235655,and RS-2024-00406007supported by BK21 FOUR(Connected AI Education&Research Program for Industry and Society Innovation,KAIST EE,No.4120200113769).
文摘Next-generation artificial tactile systems demand seamless integration with neuromorphic architectures to support on-edge computation and high-fidelity sensory signal processing.Despite significant advancements,current research remains predominantly focused on optimizing individual sensor elements,and systems utilizing single neuromorphic components encounter inherent limitations in enhancing overall functionality.Here,we present a vertically integrated in-sensor processing platform,which combines a three-dimensional antiferroelectric field-effect transistor(AFEFET)device with an aluminum nitride(AlN)piezoelectric sensor.
基金Supported by the National Natural Science Foundation of China(Nos.42250710152,42192562)the Southern Laboratory of Ocean Science and Engineering(Guangdong Zhuhai)(No.SML 2020 SP 007)。
文摘Convectively unstable processes caused by dense water subsidence are common occurrences in high-latitude oceanic regions,and significantly modulate mass and heat transport and mixing processes in the ocean.An idealized numerical experiment using the large eddy simulation method was conducted to analyze the three-dimensional flow field structure and the mechanism for dense water subsidence.Specifically,a negative salt flux is set at the sea surface,in which salt flux enters the sea surface to simulate the icing and salting-out phenomena that occur at high latitudes.Results show that the mean-state 3D flow field of dense water subsidence exhibits a hollow conical distribution.The horizontal flow field is characterized by a cyclonic vortex that driven primarily by the pressure gradient and influenced by the Coriolis effect.Moreover,the inverse vertical pressure gradient generated by this vortex inhibits the sinking of the plume,leading to its off-axis deflection and the development of an anticyclonic precession.In addition,the impact of rotation on the structure of a sinking plume within a stratified environment is discussed.Both horizontal vortex intensity and cone angle of the hollow cone flow field are increased with increasing rotation rate,resulting in a decrease in the plume’s maximum sinking depth.Variances in rotation direction cause the horizontal vortex and sinking plumes of dense water in the northern and southern hemispheres to rotate in opposite directions.
基金Project(50625101) supported by the National Science Fund for Distinguished Young Scholars of ChinaProject supported by Graduate Independent Innovation Foundation of Shandong University(GIIFSDU),ChinaProject(51071097) supported by the National Natural Science Foundation of China
文摘A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on the three-dimensional morphology of TiB2 particles.Different preparation routes result in different reaction forms,which accounts for the morphology variation of TiB2 particles.When the Al-Ti-B master alloy is prepared using ＂halide salt＂ route,TiB2 particles exhibit hexagonal platelet morphology and are independent with each other.In addition,the reaction temperature almost does not have influence on the morphology of TiB2 particles.However,TiB2 particles exhibit different morphologies at different reaction temperatures when the master alloys are prepared with Al-3B and Ti sponge.When the master alloy is prepared at 850 ℃,a kind of TiB2 particle agglomeration forms with a size larger than 5 μm.The TiB2 particles change to layered stacking morphology even dendritic morphology with the reaction temperature reaching up to 1200 ℃.
基金Project(CSTC 2010BB4301) supported by Natural Science Foundation Project of Chongqing,ChinaProject supported by the Open Fund for Key Laboratory of Manufacture and Test Techniques for Automobile Parts of Ministry of Education Chongqing University of Technology,2003,China
文摘To study the influence of roll casting process parameters on temperature and thermal-stress fields for the AZ31 magnesium alloy sheets,three-dimensional geometric and 3D finite element models for roll casting were established based on the symmetry of roll casting by ANSYS software.Meshing method and smart-sizing algorithm were used to divide finite element mesh in ANSYS software.A series of researches on the temperature and stress distributions during solidification process with different process parameters were done by 3D finite element method.The temperatures of both the liquid-solid two-phase zone and liquid phase zone were elevated with increasing pouring temperature.With the heat transfer coefficient increasing,the two-phase region for liquid-solid becomes smaller.With the pouring temperature increasing and the increase of casting speed,the length of two-phase zone rises.The optimized of process parameters（casting speed 2 m/min,pouring temperature 640 ℃ and heat transfer coefficient 15 kW/（m2·℃） with the water pouring at roller exit was used to produce magnesium alloy AZ31 sheet,and equiaxed grains with the average grain size of 50 μm were achieved after roll casting.The simulation results give better understanding of the temperature variation in phase transformation zone and the formation mechanism of hot cracks in plates during roll casting and help to design the optimized process parameters of roll casting for Mg alloy.
文摘一、作为哲学的AI for Process(一)郭为的哲学思想1.郭为是谁郭为是谁?他是一位哲学家。顺便说,他同时还领导着神州数码。为什么说郭为是哲学家呢?因为他在著作中谈到高深的哲学,如“数据如水,奔流不息,无界融合”。他引述古希腊哲学家赫拉克利特所说的“万物流转”,又说“你不能两次踏进同一条河流,因为新的水不断地流过你的身旁”,他所表达的意思是“世界上唯一不变的就是变化”。
基金This work was supported by the Brain Korea 2lProject and the Grallt of Post-Doc Program, KyungpookNational University (1999).
文摘Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic FEM code has been developed. Isothermal forging process of a cylindrical housing has been simulated. The simulation results show that the given techniques and the FEM code are reasonable and feasible for three-dimensional bulk forming processes.
基金This work was financially supported by the National Natural Science Foundation of China (No.50604007)the Natural ScienceFoundation of Liaoning Province, China (No.20062016)
文摘A self-designed setup of modified sloping cooling/shearing process was made to prepare the semisolid Al-3wt%Mg alloy. A three-dimensional simulation model was established for the analysis of preparing the semisolid Al-3wt%Mg alloy. Through simulation and experiment, it is shown that the sloping angle of the plate greatly affects temperature and velocity distributions, and the temperature and velocity of the alloy at the exit of the sloping plate increase with the increase of the sloping angle. The alloy temperature decreases linearly from the pouring mouth to the exit. The alloy temperature at the exit increases obviously with the increase of pouring temperature. To prepare the semisolid Al-3wt%Mg alloy with good quality, the sloping angle θ=45° is reasonable, and the pouring temperature is suggested to be designed above 650-660℃ but under 700℃.
文摘To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D leader-following cooperative interception guidance law.First,in the LOS direction of the leader,an impact time-controlled guidance law is derived based on the fixed-time stability theory,which enables the leader to complete the interception task at a prespecified impact time.Next,in the LOS direction of the followers,by introducing a time consensus tracking error function,a fixed-time consensus tracking guidance law is investigated to guarantee the consensus tracking convergence of the time-to-go.Then,in the direction normal to the LOS,by combining the designed global integral sliding mode surface and the second-order Sliding Mode Control(SMC)theory,an innovative 3D LOS-angle-constrained interception guidance law is developed,which eliminates the reaching phase in the traditional sliding mode guidance laws and effectively saves energy consumption.Moreover,it effectively suppresses the chattering phenomenon while avoiding the singularity issue,and compensates for unknown interference caused by target maneuvering online,making it convenient for practical engineering applications.Finally,theoretical proof analysis and multiple sets of numerical simulation results verify the effectiveness,superiority,and robustness of the investigated guidance law.
基金supported by the National Science Fund for Distinguished Young Scholars(42225107)the National Natural Science Foundation of China(42001326,42371414,42171409,and 42271419)+1 种基金the Natural Science Foundation of Guangdong Province of China(2022A1515012207)the Basic and Applied Basic Research Project of Guangzhou Science and Technology Planning(202201011539)。
文摘Three-dimensional(3D)urban structures play a critical role in informing climate mitigation strategies aimed at the built environment and facilitating sustainable urban development.Regrettably,there exists a significant gap in detailed and consistent data on 3D building space structures with global coverage due to the challenges inherent in the data collection and model calibration processes.In this study,we constructed a global urban structure(GUS-3D)dataset,including building volume,height,and footprint information,at a 500 m spatial resolution using extensive satellite observation products and numerous reference building samples.Our analysis indicated that the total volume of buildings worldwide in2015 exceeded 1×10^(12)m^(3).Over the 1985 to 2015 period,we observed a slight increase in the magnitude of 3D building volume growth(i.e.,it increased from 166.02 km3 during the 1985–2000 period to 175.08km3 during the 2000–2015 period),while the expansion magnitudes of the two-dimensional(2D)building footprint(22.51×10^(3) vs 13.29×10^(3)km^(2))and urban extent(157×10^(3) vs 133.8×10^(3)km^(2))notably decreased.This trend highlights the significant increase in intensive vertical utilization of urban land.Furthermore,we identified significant heterogeneity in building space provision and inequality across cities worldwide.This inequality is particularly pronounced in many populous Asian cities,which has been overlooked in previous studies on economic inequality.The GUS-3D dataset shows great potential to deepen our understanding of the urban environment and creates new horizons for numerous 3D urban studies.
基金Supported by the 2022 Provincial Quality Engineering Project for Higher Education Institutions,No.2022sx031the 2023 Provincial Quality Engineering Project for Higher Education Institutions,No.2023jyxm1071.
文摘BACKGROUND Inguinal hernias are common after surgery.Tension-free repair is widely accepted as the main method for managing inguinal hernias.Adequate exposure,coverage,and repair of the myopectineal orifice(MPO)are necessary.However,due to differences in race and sex,people’s body shapes vary.According to European guidelines,the patch should measure 10 cm×15 cm.If any part of the MPO is dissected,injury to the nerves,vascular network,or organs may occur during surgery,thereby leading to inguinal discomfort,pain,and seroma formation after surgery.Therefore,accurate localization and measurement of the boundary of the MPO are crucial for selecting the optimal patch for inguinal hernia repair.AIM To compare the size of the MPO measured on three-dimensional multislice spiral computed tomography(CT)with that measured via laparoscopy and explore the relevant factors influencing the size of the MPO.METHODS Clinical data from 74 patients who underwent laparoscopic tension-free inguinal hernia repair at the General Surgery Department of the First Affiliated Hospital of Anhui University of Science and Technology between September 2022 and July 2024 were collected and analyzed retrospectively.Transabdominal preperitoneal was performed.Sixty-four males and 10 females,with an average age of 58.30±12.32 years,were included.The clinical data of the patients were collected.The boundary of the MPO was measured on three-dimensional CT images before surgery and then again during transabdominal preperitoneal.All the preoperative and intraoperative data were analyzed via paired t-tests.A t-test was used for comparisons of age,body mass index,and sex between the groups.In the comparative analysis,a P value less than 0.05 indicated a significant difference.RESULTS The boundaries of the MPO on 3-dimensional CT images measured 7.05±0.47 cm and 6.27±0.61 cm,and the area of the MPO was 19.54±3.33 cm^(2).The boundaries of the MPO during surgery were 7.18±0.51 cm and 6.17±0.40 cm.The errors were not statistically significant.However,the intraoperative BD(the width of the MPO,P=0.024,P<0.05)and preoperative AC(the length of the MPO,P=0.045,P<0.05)significantly differed according to sex.The AC and BD measurements before and during surgery were not significantly different according to age,body mass index,hernia side or hernia type(P>0.05).CONCLUSION The application of this technology can aid in determining the most appropriate dissection range and patch size.
基金supported by the National Natural Science Foundation of China(Grant Nos.61274106,11175138,and 61601352)
文摘The fabrication process dependent effects on single event effects （SEEs） are investigated in a commercial silicon- germanium heterojunction bipolar transistor （SiGe HBT） using three-dimensional （3D） TCAD simulations. The influences of device structure and doping concentration on SEEs are discussed via analysis of current transient and charge collection induced by ions strike. The results show that the SEEs representation of current transient is different from representation of the charge collection for the same process parameters. To be specific, the area of C/S junction is the key parameter that affects charge collection of SEE. Both current transient and charge collection are dependent on the doping of collector and substrate. The base doping slightly influences transient currents of base, emitter, and collector terminals. However, the SEEs of SiGe HBT are hardly affected by the doping of epitaxial base and the content of Ge.
基金supported by the National 973 Fundamental Research Program of China (No.2005CB724102,2006CB705404)
文摘The traditional fuzzy logic system （FLS） can only model and control the process in two-dimensional nature. Many of real-world systems are of multidimensional features, such as, thermal and fluid processes with spatiotemporal dynamics, biological systems, or decision-making processes that contain stochastic and imprecise uncertainties. These types of systems are difficult for the traditional FLS to model and control because they require a third dimension for spatial or probabilistic information. The type-2 fuzzy set provides the possibility to develop a three-dimensional fuzzy logic system for modeling and controlling these processes in three-dimensional nature.
基金financial support from the National Natural Science Foundation of China (Nos.51904335,41630642)。
文摘True-triaxial compression tests were carried out on cubic granite samples with a circular through hole using a true-triaxial testing system to investigate the influence of saturated water content(SWC) on the failure process and characteristics of a circular tunnel of surrounding rocks. The spalling failure under SWC can be divided into four periods: calm period, buckling deformation period, period of rock fragment gradual buckling and exfoliation, and period of formation of symmetrical V-shaped notches. When the horizontal axial and vertical stresses were constant, the spalling failure severity was reduced with the increase in lateral stress. Under natural water content, a strong rockburst with dynamic failure characteristics occurred on the circular hole sidewall. Under SWC, the failure severity was reduced and the circular hole sidewall experienced spalling failure, exhibiting progressive static failure characteristics.Therefore, water can reduce the failure severity of surrounding rocks in deep underground engineering, which has a certain guiding significance for the prevention and control of rockbursts.
基金financially supported by the National Natural Science Foundation of China (No.51875124)the National Key Research and Development Project,China (No.2019YFB2006503)。
文摘To shorten the preparation process of semi-solid billets,semi-solid billets of 2A14 aluminum alloy were prepared by wrought aluminum directly semi-solid isothermal treatment(WADSSIT)process.Three-dimension(3D)combined microstructure evolution,namely transverse direction(TD)surface,rolling direction(RD)surface,and normal direction(ND)surface,was studied.Effects of temperature and holding time on average grain size and average shape factor were investigated.The results showed that the optimum conditions for preparation of 2A14 semi-solid billets by this process were 615℃ and 20 min(average grain size of 124μm and shape factor of 0.81).Electron backscatter diffraction(EBSD)observations indicated that the microstructure was completely recrystallized when it was heated to 600℃.Grain size was increased with the increase of temperature and grew up slowly with the holding time prolonging.Roundness was increased with increase of holding time but was not sensitive to temperature.
文摘The extremely high peak intensity associated with ultrashort pulse width of femtosecond(fs)lasers enabled inducing nonlinear multiphoton absorption in materials that are transparent to the laser wavelength.More importantly,focusing the fs laser beam inside the transparent materials confined the nonlinear interaction to within the focal volume only,realizing three-dimensional(3D)micro/nanofabrication.This 3D capability offers three different processing schemes for use in fabrication:undeformative,subtractive,and additive.Furthermore,a hybrid approach of different schemes can create much more complex 3D structures and thereby promises to enhance the functionality of the structures created.Thus,hybrid fs laser 3D microprocessing opens a new door for material processing.This paper comprehensively reviews different types of hybrid fs laser 3D micro/nanoprocessing for diverse applications including fabrication of functional micro/nanodevices.
文摘Air separators provide safe, clean, and appropriate air flow to engines and are widely used in vehicles with large engines such as ships and submarines. In this operational study, the separation process in a Ranque-Hilsch vortex tube cleaning （cooling） system is investigated to analyze the impact of the operating gas type on the vortex tube performance; the operating gases used are air, nitrogen, oxygen, carbon dioxide and nitrogen dioxide. The computational fluid dynamic model used is equipped with a three-dimensional structure, and the steady-state condition is applied during computations. The standard k-c turbulence model is employed to resolve nonlinear flow equations, and various key parameters, such as hot and cold exhaust thermal drops, and power separation rates, are described numerically. The results show that nitrogen dioxide creates the greatest separation power out of all gases tested, and the numerical results are validated by good agreement with available experimental data. In addition, a comparison is made between the use of two different boundary conditions, the pressure-far-field and the pressure-outlet, when analyzing complex turbulent flows in the air separators. Results present a comprehensive and practical solution for use in future numerical studies.
