Scouring experiments were conducted using a three-dimensional laser scanning technology for angles of the jet spanning the interval from 0°to 30°,and the characteristics of the scour hole in equilibrium cond...Scouring experiments were conducted using a three-dimensional laser scanning technology for angles of the jet spanning the interval from 0°to 30°,and the characteristics of the scour hole in equilibrium conditions were investigated accordingly.The results indicate that the optimal scouring effects occur when the jet angle is in the ranges between 15°and 20°.Moreover,the dimensionless profiles of the scour hole exhibit a high degree of similarity at different jet angles.Numerical simulations conducted using the Flow-3D software to investigate the bed shear stress along the jet impingement surface have shown that this stress is influenced by both the resultant force and the jet impingement surface area.It reaches its maximum value when the jet is vertical,decreases rapidly as the jet starts to tilt,then increases slightly,and decreases again significantly when the angle exceeds 20°.展开更多
The present study examines the results of the researches related to the gob bulking factor carried out at home and abroad.A mathematical function of a three-dimensional gob bulking factor is described based on a three...The present study examines the results of the researches related to the gob bulking factor carried out at home and abroad.A mathematical function of a three-dimensional gob bulking factor is described based on a three-dimensional gob model.The method of taking value for interstice and permeability ratios is also proposed.The law of air leakage of fully mechanized top coal is researched in this study.The results show that the speed of air flow near the upper and lower crossheadings is higher than that in the central section of the gob at the same distance from the working face.When the amount of air at the working face exceeds a critical amount,the width of the spontaneous combustion zone in the upper and lower crossheadings is also larger than that in the central section.In this situation,the key is preventing the coal left in the upper and lower crossheadings from self-igniting.Reducing the amount of air at the working face can decrease the width of the spontaneous combustion zone,especially the width near the upper and lower crossheadings.This also moves the spontaneous combustion zone in the direction of the working face.It can prevent the coal in the gob from self-igniting by making the coal left in the crossheadings to be inert and by effectively controlling the amount of air at the working face.展开更多
The motion of gas bubbles beneath a free surface will lead to a spike of fluid on the free surface. The distance of the bubbles to the free surface is the key factor to different phenomena. When the inception distance...The motion of gas bubbles beneath a free surface will lead to a spike of fluid on the free surface. The distance of the bubbles to the free surface is the key factor to different phenomena. When the inception distance varies in some range, crown phenomenon would happen after the impact of weak buoyancy bubbles, so this kind of spike is defined as crown spike in the present paper. Based on potential flow theory, a three-dimensional numerical model is established to simulate the motion of the free-surface spike generated by one bubble or a horizontal line of two in-phase bubbles. After the downward jet formed near the end of the collapse phase, the simulation of the free surface is performed to study the crown spike without regard to the toroidal bubble＇s effect. Calculations about the interaction between one bubble and free surface agree well with the experimental results conducted with a high-speed camera, and relative error is within 15%. Crown spike in both single- and two-bubble cases are simulated numerically. Different features and laws of the motion of crown spike, depending on the bubble-boundary distances and the inter-bubble distances, have been investigated.展开更多
A three-dimensional isopycnic-coordinate internal tidal model is employed to investigate the generation, propagation, vertical structure and energy conversion ofM2 internal tides in the Luzon Strait （LS） with moorin...A three-dimensional isopycnic-coordinate internal tidal model is employed to investigate the generation, propagation, vertical structure and energy conversion ofM2 internal tides in the Luzon Strait （LS） with mooring observations. Simulated results, especially the tidal current amplitudes, agree well with observations, demonstrating the reasonability and accuracy of the model. Results indicate that M2 internal tides mainly propagate into three directions horizontally, i.e., eastward towards the western Pacific Ocean, westward towards the Dongsha Island and southwestward towards the South China Sea Basin. In the horizontal direction, tidal current amplitudes decrease as distance increases away from the LS; in the vertical direction, they show an obvious decreasing tendency with depth. Between the double ridges of the LS, a clockwise gyre of M2 baroclinic energy flux appears, which is caused by reflections of M2 internal tides at supercritical topographies, and resonance of M2 internal tides happens along 19.5° and 21.5°N due to the heights and separation distance of the double ridges. The total energy conversion in the LS is about 14.20 GW.展开更多
The change of bubbles and the position of the tuyere in an oxygen coal combustion melting and separating furnace affect the flow and splash behavior of the molten pool.To analyze this problem further,a three-dimension...The change of bubbles and the position of the tuyere in an oxygen coal combustion melting and separating furnace affect the flow and splash behavior of the molten pool.To analyze this problem further,a three-dimensional numerical simulation method was used to explore the behavior and change of the flow field inside the molten pool during double-row tuyere injection.In addition,the arrangement of the tuyere was changed for a more detailed understanding of the internal phase distribution and splashing in a molten pool.The results indicated that under three-dimensional numerical simulation conditions,bubbles rise after leaving the tuyere and break on the surface of the molten pool,which results in certain fluctuations in the nearby melt.During the injection process of the tuyere,the meteorological accumulation in the middle part of the molten pool formed part of the foam slag because of the influence of surface tension.When the layout of the upper and lower exhaust tuyeres was changed from staggered to symmetrical,or when the spacing of the upper and lower exhaust tuyeres changed,it had an effect on the phase distribution and splash behavior.展开更多
The influences of large areas of semi-unbounded cold water surface on the evolution, propagation and precipitation production of thunderstorms are simulated by using a fully elastic three-dimensional numerical hailsto...The influences of large areas of semi-unbounded cold water surface on the evolution, propagation and precipitation production of thunderstorms are simulated by using a fully elastic three-dimensional numerical hailstorm model. Real sounding profiles for temperature, humidity and wind are employed. The model has successfully simulated the significant modification of the propagation path of thunderstorms near the cold water area. The path change can be either' along-bank' or' toward-bank', depending on the position of the storm system relative to convergence zone of the water-land circulation. The simulations also show that thunderstorms developing or propagating within the convergence zone of local circulation will be intensified and produce much heavier hail, whereas those over cold water surface or the air that has been cooled by the water will be strongly inhibited.The influence of the cold water surface on thunderstorm characters is largely dependent upon the direction and intensity of the low-level wind.展开更多
Plasma sprayed coatings are built up by the accumulation of splats formed by the impacting,spreading and solidifying of molten droplets on the substrate.A three-dimensional computational model including heat transfer ...Plasma sprayed coatings are built up by the accumulation of splats formed by the impacting,spreading and solidifying of molten droplets on the substrate.A three-dimensional computational model including heat transfer and solidification is established to simulate the formation process of a single splat using the computational fluid dynamics(CFD)software,FLUENT.The fluid flow and energy equations are discretized and solved according to typical finite volume method on an unstructured grid.A volume of fluid(VOF)tracking algorithm is used to track the droplet flow with free surface.In order to understand the splat formation mechanism,the process of splat formation caused by impacting and spreading of a molten nickel droplet on a polished mild steel surface is simulated.On this basis,the simulations of impact of a molten droplet on substrate with different conditions including the surface morphology,thermal conductivity,initial temperature of the substrate and the thermal contact resistance are presented.The results clearly show the effect of those parameters on the shape of the final splat and splash behaviors.展开更多
Recent satellite altimeter observations have indicated that internal tides （ITs） from the Luzon Strait （LS） propagate more than 2 500 km into the Western Pacific （WP）. This study used a high-resolution three-dim...Recent satellite altimeter observations have indicated that internal tides （ITs） from the Luzon Strait （LS） propagate more than 2 500 km into the Western Pacific （WP）. This study used a high-resolution three-dimensional numerical model to reproduce and examine the ITs radiation process. The propagation of diurnal and semidiurnal ITs showed different patterns and variations. Diurnal ITs with lower frequency were affected more by the earth＇s rotation and they were bent more toward the equator than semidiurnal ITs. ITs phase speeds are functions of latitude and diurnal ITs showed greater distinctions of phase speeds during propagation. For M2 ITs, the wavelength remained nearly unchanged but the beam width increased significantly during propagation away from the LS. For diurnal ITs （K1 and O0, the wavelength decreased noticeably with latitude, while the beam width varied little during propagation because of blocking by land. Baroclinic energy was also examined as a complement to satellite results reported by Zhao （2014）. The magnitude of the generated baroclinic energy flux reduced remarkably within 300 km from the generation site but it then decayed slowly when propagating into abyssal sea. Baroclinic energy of diurnal ITs was found to dissipate at a slower rate than semidiurnal ITs along the main propagation path in the WP.展开更多
Large-scale,fine,and efficient numerical simulation of a geothermal field plays an important role in geothermal energy development.Confronted with the problem of large computation and high storage requirements for com...Large-scale,fine,and efficient numerical simulation of a geothermal field plays an important role in geothermal energy development.Confronted with the problem of large computation and high storage requirements for complex underground models in a three-dimensional(3-D)numerical simulation of a geothermal fi eld,a mixed space-wavenumber domain 3-D numerical simulation algorithm is proposed in this paper.According to the superposition principle of temperature field,the geothermal field is decomposed into background and abnormal temperature fi elds for calculation.The uniform layered model is used to solve the background field.When the abnormal field is solved,the horizontal two-dimensional(2-D)Fourier transform is used to transform the 3-D diff erential equation satisfi ed by an abnormal field into a series of one-dimensional ordinary differential equations with diff erent wavenumbers,which greatly reduces the calculation and storage.The unit division of an ordinary diff erential equation is fl exible,and the calculation amount is small.The algorithm fully takes advantage of the effi ciency of the Fourier transform and the quickness of the catch-up method to solve linear equations with a fixed bandwidth,which effectively improves the computational efficiency.Compared with the COMSOL Multiphysics professional simulation finite element software,the time consumption and memory requirements of the algorithm proposed in this paper are reduced by multiple orders of magnitude in terms of ensuring accuracy and the same mesh division.The more the number of calculated nodes is,the more obvious is the advantage.We design models to study the thermal conductivity,heat fl ux boundary,regional tectonic morphology,and topographic relief of the geothermal fi eld distribution.A 3-D geophysical model is developed based on topographic elevation data,geothermal geology,and geophysical exploration data in the Qiabuqia area of Gonghe Basin,Qinghai Province,China.Numerical simulation of the geothermal fi eld in this area is realized,which shows that the algorithm is suitable for precise and effi cient simulation of an arbitrary complex terrain and geological conditions.展开更多
In order to study the effect of rotation on the combustion in the underwater vehicle,a two-phase turbulent combustion process is described with Reynolds stress turbulence model,eddy-dissipation turbulent combustion mo...In order to study the effect of rotation on the combustion in the underwater vehicle,a two-phase turbulent combustion process is described with Reynolds stress turbulence model,eddy-dissipation turbulent combustion model,P-1 radiation model and particle tracking model of liquid. The flow in the rotating combustion chamber is simulated at two different working speeds,0?r/min and 1?000?r/min by Fluent software. The temperature,gas velocity,static pressure of wall and fuel concentration are computed and compared. The results show that the combustion in rotating combustor is faster and more effective.展开更多
As a renewable energy source,the thermal conversion of poultry manure,is a promising waste treatment solution that can generate circular economic outputs such as energy and reduce greenhouse gas emissions.Currently,pr...As a renewable energy source,the thermal conversion of poultry manure,is a promising waste treatment solution that can generate circular economic outputs such as energy and reduce greenhouse gas emissions.Currently,pressurized gasification of poultry manure is still a novel research field,especially when combined with a novel technological route of oxy-fuel gasification.Oxy-fuel gasification is a newly proposed and promising gasification technology for power generation that facilitates future carbon capture and storage.In this work,based on a commercially operated industrial-scale chicken manure gasification power plant in Singapore,we presented an interesting first exploration of the coupled pressurization technology for oxy-fuel gasification of poultry manure using CFD numerical simulation,analyzed the effects of pressure and oxygen enrichment concentration as well as the coupling mechanism between them,and discussed the conversion and emission of nitrogen-and sulfur-containing pollutants.The results indicate that under oxy-fuel gasification condition(Oxy-30,i.e.,30%O_(2)/70%CO_(2)),as the pressure increases from 0.1 to 0.5 MPa,the CO concentration in the syngas increases slightly,the H_(2)concentration increases to approximately 25%,and the CH4 concentration(less than 1%)decreases,resulting in an increase in the calorific value of syngas from 5.2 to 5.6 MJ·m^(-3).Compared to atmospheric pressure conditions,a relatively higher oxygen-enriched concentration interval(Oxy-40 to Oxy-50)under pressurized conditions is advantageous for autothermal gasification.Pressurization increases NO precursors production and also promotes homogeneous and heterogeneous reduction of NO,and provides favorable conditions for self-desulfurization.This work offers reference for the realization of a highly efficient and low-energy-consumption thermochemical treatment of livestock manure coupled with negative carbon emission technology.展开更多
The graded density impactor(GDI)dynamic loading technique is crucial for acquiring the dynamic physical property parameters of materials used in weapons.The accuracy and timeliness of GDI structural design are key to ...The graded density impactor(GDI)dynamic loading technique is crucial for acquiring the dynamic physical property parameters of materials used in weapons.The accuracy and timeliness of GDI structural design are key to achieving controllable stress-strain rate loading.In this study,we have,for the first time,combined one-dimensional fluid computational software with machine learning methods.We first elucidated the mechanisms by which GDI structures control stress and strain rates.Subsequently,we constructed a machine learning model to create a structure-property response surface.The results show that altering the loading velocity and interlayer thickness has a pronounced regulatory effect on stress and strain rates.In contrast,the impedance distribution index and target thickness have less significant effects on stress regulation,although there is a matching relationship between target thickness and interlayer thickness.Compared with traditional design methods,the machine learning approach offers a10^(4)—10^(5)times increase in efficiency and the potential to achieve a global optimum,holding promise for guiding the design of GDI.展开更多
A suction casting experiment was conducted on Zr_(55)Cu_(30)Al_(10)Ni_(5)(at%)amorphous alloy.Using ProCAST software,numerical simulations were performed to analyze the filling and solidification processes.The velocit...A suction casting experiment was conducted on Zr_(55)Cu_(30)Al_(10)Ni_(5)(at%)amorphous alloy.Using ProCAST software,numerical simulations were performed to analyze the filling and solidification processes.The velocity field during the filling process and the temperature field during the solidification process of the alloy melt under different process parameters were obtained.Based on the simulation results,a Zr-based amorphous alloy micro-gear was prepared via casting.The results indicate that increasing the suction casting temperature enhances the fluidity of alloy melt but induces unstable flow rate during filling,which is detrimental to complete filling.Zr-based amorphous micro-gears with a module of 0.6 mm,a tooth top diameter of 8 mm,and 10 teeth were prepared through the suction casting.X-ray diffraction and differential scanning calorimetry analyses confirm that the fabricated micro-gear exhibits characteristic amorphous structural features,demonstrating well-defined geometrical contours and satisfactory forming completeness.展开更多
Heat treatment processes, such as annealing and quenching, are crucial in determining residual stress evolution, microstructural changes and mechanical properties of metallic materials, with residual stresses playing ...Heat treatment processes, such as annealing and quenching, are crucial in determining residual stress evolution, microstructural changes and mechanical properties of metallic materials, with residual stresses playing a greater role in the performance of components. This paper investigates the effect of heat treatment on residual stresses induced in AISI 1025, manufactured using LENS. Finite element model was developed and simulated to analyze residual stress development. AISI 1025 samples suitable for tool and die applications in Fused Deposition Modelling (FDM) filament production, were fabricated using Laser Engineered Net Shaping (LENS) process, followed by heat treatment where annealing and quenching processes were done. The material’s microstructure, residual stress and hardness of heat-treated samples under investigation, were compared against the as-built samples. The results indicated that after annealing, tensile residual stresses were reduced by 93%, resulting in a reduced crack growth rate, compared to the as-built sample, although the hardness was reduced significantly by 25%. On the other hand, high tensile residual stresses of 425 ± 14 MPa were recorded after quenching process with an improvement of hardness by 21%.展开更多
Hydrogen displays the potential to partially replace pulverized coal injection(PCI)in the blast furnace,and it can reduce CO_(2)emissions.In this paper,a three-dimensional mathematical model of hydrogen and pulverized...Hydrogen displays the potential to partially replace pulverized coal injection(PCI)in the blast furnace,and it can reduce CO_(2)emissions.In this paper,a three-dimensional mathematical model of hydrogen and pulverized coal co-injection in blast furnace tuyere was established through numerical simulation,and the effect of hydrogen injection and oxygen enrichment interaction on pulverized coal combustion and raceway smelting was investigated.The simulation results indicate that when the coal injection rate decreased from 36 to 30t/h and the hydrogen injection increased from 0 to 3600 m^(3)/h,the CO_(2)emissions decreased from 1860 to 1551 kg/t,which represents a16.6%reduction,and the pulverized coal burnout decreased from 70.1%to 63.7%.The heat released from hydrogen combustion can not only promote the volatilization of pulverized coal but also affect the combustion reaction between volatilization and oxygen,which resulted in a decrease in the temperature at the end of the raceway.Co-injection of hydrogen with PCI increased the wall temperature near the upper half part of the raceway and at the outlet of the tuyere,which required a high cooling efficiency to extend the service life of the blast furnace.The increase in oxygen level compensated for the decreased average temperature in the raceway due to hydrogen injection.The increase in the oxygen content by 3%while maintaining constant hydrogen and PCI injection rates increased the burnout and average raceway temperature by 4.2%and 43 K,respectively.The mole fraction of CO and H_(2) production increased by 0.04 and 0.02,respectively.Burnout can be improved through optimization of the particle size distribution of pulverized coal.展开更多
We proposed a new technique route of directional solidification for the manufacture of super slab.A 7-t laboratory-scale thick slab was casted and characterised for trial.To further understand the process,the evolutio...We proposed a new technique route of directional solidification for the manufacture of super slab.A 7-t laboratory-scale thick slab was casted and characterised for trial.To further understand the process,the evolution of the multiple physical fields during the directional solidification was simulated and verified.Similar to the convectional ingot casting,a negative segregated cone of equiaxed grains was formed at the bottom,and a seriously positive segregated region was formed beneath the top surface of the slab.Specific measures on the lateral walls,base plate,and free surface were strongly recommended to ensure that the slab is relatively directionally casted.A water-cooling copper base plate accelerates the solidification rate and the columnar growth along the vertical direction.It inhibits the sedimentation of equiaxed grains and enlarges the columnar zone.Based on the simulation analysis,it can be concluded that the directional solidification technique route is promising to manufacture super slab with lower segregation level,and less porosities and inclusions.展开更多
In this study,a new linear friction welding(LFW)process,embedded LFW process,was put forward,which was mainly applied to combination manufacturing of long or overlong loadcarrying titanium alloy structural components ...In this study,a new linear friction welding(LFW)process,embedded LFW process,was put forward,which was mainly applied to combination manufacturing of long or overlong loadcarrying titanium alloy structural components in aircraft.The interfacial plastic flow behavior and bonding mechanism of this process were investigated by a developed coupling EulerianLagrangian numerical model using software ABAQUS and a novel thermo-physical simulation method with designed embedded hot compression specimen.In addition,the formation mechanism and control method of welding defects caused by uneven plastic flow were discussed.The results reveal that the plastic flow along oscillating direction of this process is even and sufficient.In the direction perpendicular to oscillation,thermo-plastic metals mainly flow downward along welding interface under coupling of shear stress and interfacial pressure,resulting in the interfacial plastic zone shown as an inverted“V”shape.The upward plastic flow in this direction is relatively weak,and only a small amount of flash is extruded from top of joint.Moreover,the wedge block and welding components at top of joint are always in un-steady friction stage,leading to nonuniform temperature field distribution and un-welded defects.According to the results of numerical simulation,high oscillating frequency combined with low pressure and small amplitude is considered as appropriate parameter selection scheme to improve the upward interfacial plastic flow at top of joint and suppress the un-welded defects.The results of thermo-physical simulation illustrate that continuous dynamic recrystallization(CDRX)induces the bonding of interface,accompanying by intense dislocation movement and creation of many low-angle grain boundaries.In the interfacial bonding area,grain orientation is random with relatively low texture density(5.0 mud)owing to CDRX.展开更多
The nozzle is a critical component responsible for generating most of the net thrust in a scramjet engine.The quality of its design directly affects the performance of the entire propulsion system.However,most turbule...The nozzle is a critical component responsible for generating most of the net thrust in a scramjet engine.The quality of its design directly affects the performance of the entire propulsion system.However,most turbulence models struggle to make accurate predictions for subsonic and supersonic flows in nozzles.In this study,we explored a novel model,the algebraic stress model k-kL-ARSM+J,to enhance the accuracy of turbulence numerical simulations.This new model was used to conduct numerical simulations of the design and off-design performance of a 3D supersonic asymmetric truncated nozzle designed in our laboratory,with the aim of providing a realistic pattern of changes.The research indicates that,compared to linear eddy viscosity turbulence models such as k-kL and shear stress transport(SST),the k-kL-ARSM+J algebraic stress model shows better accuracy in predicting the performance of supersonic nozzles.Its predictions were identical to the experimental values,enabling precise calculations of the nozzle.The performance trends of the nozzle are as follows:as the inlet Mach number increases,both thrust and pitching moment increase,but the rate of increase slows down.Lift peaks near the design Mach number and then rapidly decreases.With increasing inlet pressure,the nozzle thrust,lift,and pitching moment all show linear growth.As the flight altitude rises,the internal flow field within the nozzle remains relatively consistent due to the same supersonic nozzle inlet flow conditions.However,external to the nozzle,the change in external flow pressure results in the nozzle exit transitioning from over-expanded to under-expanded,leading to a shear layer behind the nozzle that initially converges towards the nozzle center and then diverges.展开更多
The local time-stepping(LTS)algorithm is an adaptive method that adjusts the time step by selecting suitable intervals for different regions based on the spatial scale of each cell and water depth and flow velocity be...The local time-stepping(LTS)algorithm is an adaptive method that adjusts the time step by selecting suitable intervals for different regions based on the spatial scale of each cell and water depth and flow velocity between cells.The method can be optimized by calculating the maximum power of two of the global time step increments in the domain,allowing the optimal time step to be approached throughout the grid.To verify the acceleration and accuracy of LTS in storm surge simulations,we developed a model to simulate astronomical storm surges along the southern coast of China.This model employs the shallow water equations as governing equations,numerical discretization using the finite volume method,and fluxes calculated by the Roe solver.By comparing the simulation results of the traditional global time-stepping algorithm with those of the LTS algorithm,we find that the latter fit the measured data better.Taking the calculation results of Typhoon Sally in 1996 as an example,we show that compared with the traditional global time-stepping algorithm,the LTS algorithm reduces computation time by 2.05 h and increases computation efficiency by 2.64 times while maintaining good accuracy.展开更多
As the integration of electronic components in high-performance servers increases,heat generation significantly impacts performance and raises failure rates.Therefore,heat dissipation has become a critical concern in ...As the integration of electronic components in high-performance servers increases,heat generation significantly impacts performance and raises failure rates.Therefore,heat dissipation has become a critical concern in electronic circuit design.This study uses numerical simulations to investigate the heat dissipation characteristics of electronic components in air-cooled servers.By adjusting airflow speed,heat sink configurations,and the arrangement of straight-fin heat sinks,we optimize heat dissipation performance and analyze the mechanisms at different airflow speeds.The results show that,at the same airflow speed,the temperature of the heat sink is lower than that of the electronic components,creating a temperature gradient that enhances heat transfer.Compared to a front-to-back arrangement of two straight-fin heat sinks,placing the heat sinks parallel to each other results in a lower maximum component temperature and better temperature uniformity.Heat sinks with fins significantly improve heat dissipation.The heat sink with semicylindrical fins on the rib surface provides the best cooling performance.Moreover,compared to natural convection,the maximum temperature of the electronic components decreases by 56.17%and 61%when the incoming flow velocity is 6 m/s with two parallel flat ribbed heat sinks and front-to-back arrangement,respectively.展开更多
基金supported by Research on the Influence of Nozzle Structure on the Scouring Effect of Submerged Water Jet(2023R411045)Design and Control Strategy Research of PEM Fuel Cell Hybrid Propulsion System for Ships(2024R411015)+1 种基金Zhejiang Ocean University Outstanding Master’s Thesis Cultivation Project(ZJOUYJS20230018)General Program of Education Department of Zhejiang Province(Y202250817)which was gained by Chen.
文摘Scouring experiments were conducted using a three-dimensional laser scanning technology for angles of the jet spanning the interval from 0°to 30°,and the characteristics of the scour hole in equilibrium conditions were investigated accordingly.The results indicate that the optimal scouring effects occur when the jet angle is in the ranges between 15°and 20°.Moreover,the dimensionless profiles of the scour hole exhibit a high degree of similarity at different jet angles.Numerical simulations conducted using the Flow-3D software to investigate the bed shear stress along the jet impingement surface have shown that this stress is influenced by both the resultant force and the jet impingement surface area.It reaches its maximum value when the jet is vertical,decreases rapidly as the jet starts to tilt,then increases slightly,and decreases again significantly when the angle exceeds 20°.
基金Financial support for this work was obtained from the National Natural Science Foundation of China(No.51074059)
文摘The present study examines the results of the researches related to the gob bulking factor carried out at home and abroad.A mathematical function of a three-dimensional gob bulking factor is described based on a three-dimensional gob model.The method of taking value for interstice and permeability ratios is also proposed.The law of air leakage of fully mechanized top coal is researched in this study.The results show that the speed of air flow near the upper and lower crossheadings is higher than that in the central section of the gob at the same distance from the working face.When the amount of air at the working face exceeds a critical amount,the width of the spontaneous combustion zone in the upper and lower crossheadings is also larger than that in the central section.In this situation,the key is preventing the coal left in the upper and lower crossheadings from self-igniting.Reducing the amount of air at the working face can decrease the width of the spontaneous combustion zone,especially the width near the upper and lower crossheadings.This also moves the spontaneous combustion zone in the direction of the working face.It can prevent the coal in the gob from self-igniting by making the coal left in the crossheadings to be inert and by effectively controlling the amount of air at the working face.
基金Project supported by the Major Basic Research Project of National Security of China(Grant No.613157)the Excellent Young Scientists Fund of China(Grant No.51222904)
文摘The motion of gas bubbles beneath a free surface will lead to a spike of fluid on the free surface. The distance of the bubbles to the free surface is the key factor to different phenomena. When the inception distance varies in some range, crown phenomenon would happen after the impact of weak buoyancy bubbles, so this kind of spike is defined as crown spike in the present paper. Based on potential flow theory, a three-dimensional numerical model is established to simulate the motion of the free-surface spike generated by one bubble or a horizontal line of two in-phase bubbles. After the downward jet formed near the end of the collapse phase, the simulation of the free surface is performed to study the crown spike without regard to the toroidal bubble＇s effect. Calculations about the interaction between one bubble and free surface agree well with the experimental results conducted with a high-speed camera, and relative error is within 15%. Crown spike in both single- and two-bubble cases are simulated numerically. Different features and laws of the motion of crown spike, depending on the bubble-boundary distances and the inter-bubble distances, have been investigated.
基金The National High Technology Research and Development Program(863 Program) of China under contract Nos2013AA122803 and 2013AA09A502the National Natural Science Foundation of China under contract Nos 41206001 and 41371496the National Science and Technology Support Program under contract No.2013BAK05B04
文摘A three-dimensional isopycnic-coordinate internal tidal model is employed to investigate the generation, propagation, vertical structure and energy conversion ofM2 internal tides in the Luzon Strait （LS） with mooring observations. Simulated results, especially the tidal current amplitudes, agree well with observations, demonstrating the reasonability and accuracy of the model. Results indicate that M2 internal tides mainly propagate into three directions horizontally, i.e., eastward towards the western Pacific Ocean, westward towards the Dongsha Island and southwestward towards the South China Sea Basin. In the horizontal direction, tidal current amplitudes decrease as distance increases away from the LS; in the vertical direction, they show an obvious decreasing tendency with depth. Between the double ridges of the LS, a clockwise gyre of M2 baroclinic energy flux appears, which is caused by reflections of M2 internal tides at supercritical topographies, and resonance of M2 internal tides happens along 19.5° and 21.5°N due to the heights and separation distance of the double ridges. The total energy conversion in the LS is about 14.20 GW.
基金supported by the National Key R&D Program of China(2017YFB0603800 and 2017YFB0603802).
文摘The change of bubbles and the position of the tuyere in an oxygen coal combustion melting and separating furnace affect the flow and splash behavior of the molten pool.To analyze this problem further,a three-dimensional numerical simulation method was used to explore the behavior and change of the flow field inside the molten pool during double-row tuyere injection.In addition,the arrangement of the tuyere was changed for a more detailed understanding of the internal phase distribution and splashing in a molten pool.The results indicated that under three-dimensional numerical simulation conditions,bubbles rise after leaving the tuyere and break on the surface of the molten pool,which results in certain fluctuations in the nearby melt.During the injection process of the tuyere,the meteorological accumulation in the middle part of the molten pool formed part of the foam slag because of the influence of surface tension.When the layout of the upper and lower exhaust tuyeres was changed from staggered to symmetrical,or when the spacing of the upper and lower exhaust tuyeres changed,it had an effect on the phase distribution and splash behavior.
基金This work is supported by LASG, IAP, Chinese Academy of Sciences.
文摘The influences of large areas of semi-unbounded cold water surface on the evolution, propagation and precipitation production of thunderstorms are simulated by using a fully elastic three-dimensional numerical hailstorm model. Real sounding profiles for temperature, humidity and wind are employed. The model has successfully simulated the significant modification of the propagation path of thunderstorms near the cold water area. The path change can be either' along-bank' or' toward-bank', depending on the position of the storm system relative to convergence zone of the water-land circulation. The simulations also show that thunderstorms developing or propagating within the convergence zone of local circulation will be intensified and produce much heavier hail, whereas those over cold water surface or the air that has been cooled by the water will be strongly inhibited.The influence of the cold water surface on thunderstorm characters is largely dependent upon the direction and intensity of the low-level wind.
文摘Plasma sprayed coatings are built up by the accumulation of splats formed by the impacting,spreading and solidifying of molten droplets on the substrate.A three-dimensional computational model including heat transfer and solidification is established to simulate the formation process of a single splat using the computational fluid dynamics(CFD)software,FLUENT.The fluid flow and energy equations are discretized and solved according to typical finite volume method on an unstructured grid.A volume of fluid(VOF)tracking algorithm is used to track the droplet flow with free surface.In order to understand the splat formation mechanism,the process of splat formation caused by impacting and spreading of a molten nickel droplet on a polished mild steel surface is simulated.On this basis,the simulations of impact of a molten droplet on substrate with different conditions including the surface morphology,thermal conductivity,initial temperature of the substrate and the thermal contact resistance are presented.The results clearly show the effect of those parameters on the shape of the final splat and splash behaviors.
基金Supported by the National Natural Science Foundation of China(Nos.41528601,41376029,U1406401,41421005)the Strategic Pioneering Research Program of CAS(Nos.XDA10020104,XDA10020101)the CAS Interdisciplinary Innovation Team“Ocean Mesoscale Dynamical Processes and ecological effect”
文摘Recent satellite altimeter observations have indicated that internal tides （ITs） from the Luzon Strait （LS） propagate more than 2 500 km into the Western Pacific （WP）. This study used a high-resolution three-dimensional numerical model to reproduce and examine the ITs radiation process. The propagation of diurnal and semidiurnal ITs showed different patterns and variations. Diurnal ITs with lower frequency were affected more by the earth＇s rotation and they were bent more toward the equator than semidiurnal ITs. ITs phase speeds are functions of latitude and diurnal ITs showed greater distinctions of phase speeds during propagation. For M2 ITs, the wavelength remained nearly unchanged but the beam width increased significantly during propagation away from the LS. For diurnal ITs （K1 and O0, the wavelength decreased noticeably with latitude, while the beam width varied little during propagation because of blocking by land. Baroclinic energy was also examined as a complement to satellite results reported by Zhao （2014）. The magnitude of the generated baroclinic energy flux reduced remarkably within 300 km from the generation site but it then decayed slowly when propagating into abyssal sea. Baroclinic energy of diurnal ITs was found to dissipate at a slower rate than semidiurnal ITs along the main propagation path in the WP.
基金supported by National Natural Science Foundation of China(No.41574127,42174080)Innovation research team project of Guangxi Natural Science Foundation(No.GXNSFGA380004)Central South University independent exploration and innovation project for Postgraduates(Nos.2021zzts0831,2021zzts0271)
文摘Large-scale,fine,and efficient numerical simulation of a geothermal field plays an important role in geothermal energy development.Confronted with the problem of large computation and high storage requirements for complex underground models in a three-dimensional(3-D)numerical simulation of a geothermal fi eld,a mixed space-wavenumber domain 3-D numerical simulation algorithm is proposed in this paper.According to the superposition principle of temperature field,the geothermal field is decomposed into background and abnormal temperature fi elds for calculation.The uniform layered model is used to solve the background field.When the abnormal field is solved,the horizontal two-dimensional(2-D)Fourier transform is used to transform the 3-D diff erential equation satisfi ed by an abnormal field into a series of one-dimensional ordinary differential equations with diff erent wavenumbers,which greatly reduces the calculation and storage.The unit division of an ordinary diff erential equation is fl exible,and the calculation amount is small.The algorithm fully takes advantage of the effi ciency of the Fourier transform and the quickness of the catch-up method to solve linear equations with a fixed bandwidth,which effectively improves the computational efficiency.Compared with the COMSOL Multiphysics professional simulation finite element software,the time consumption and memory requirements of the algorithm proposed in this paper are reduced by multiple orders of magnitude in terms of ensuring accuracy and the same mesh division.The more the number of calculated nodes is,the more obvious is the advantage.We design models to study the thermal conductivity,heat fl ux boundary,regional tectonic morphology,and topographic relief of the geothermal fi eld distribution.A 3-D geophysical model is developed based on topographic elevation data,geothermal geology,and geophysical exploration data in the Qiabuqia area of Gonghe Basin,Qinghai Province,China.Numerical simulation of the geothermal fi eld in this area is realized,which shows that the algorithm is suitable for precise and effi cient simulation of an arbitrary complex terrain and geological conditions.
文摘In order to study the effect of rotation on the combustion in the underwater vehicle,a two-phase turbulent combustion process is described with Reynolds stress turbulence model,eddy-dissipation turbulent combustion model,P-1 radiation model and particle tracking model of liquid. The flow in the rotating combustion chamber is simulated at two different working speeds,0?r/min and 1?000?r/min by Fluent software. The temperature,gas velocity,static pressure of wall and fuel concentration are computed and compared. The results show that the combustion in rotating combustor is faster and more effective.
基金supported by the National Natural Science Foundation of China(52306131)the Natural Science Foundation of Jiangsu Province(BK20230847)+2 种基金the Key Project of the National Natural Science Foundation of China(52336005)the Fundamental Research Funds for the Central Universities(2242024RCB0036)the Open Project Program of State Key Laboratory of Low-carbon Smart Coal-fired Power Generation and Ultra-clean Emission(D2024FK156).
文摘As a renewable energy source,the thermal conversion of poultry manure,is a promising waste treatment solution that can generate circular economic outputs such as energy and reduce greenhouse gas emissions.Currently,pressurized gasification of poultry manure is still a novel research field,especially when combined with a novel technological route of oxy-fuel gasification.Oxy-fuel gasification is a newly proposed and promising gasification technology for power generation that facilitates future carbon capture and storage.In this work,based on a commercially operated industrial-scale chicken manure gasification power plant in Singapore,we presented an interesting first exploration of the coupled pressurization technology for oxy-fuel gasification of poultry manure using CFD numerical simulation,analyzed the effects of pressure and oxygen enrichment concentration as well as the coupling mechanism between them,and discussed the conversion and emission of nitrogen-and sulfur-containing pollutants.The results indicate that under oxy-fuel gasification condition(Oxy-30,i.e.,30%O_(2)/70%CO_(2)),as the pressure increases from 0.1 to 0.5 MPa,the CO concentration in the syngas increases slightly,the H_(2)concentration increases to approximately 25%,and the CH4 concentration(less than 1%)decreases,resulting in an increase in the calorific value of syngas from 5.2 to 5.6 MJ·m^(-3).Compared to atmospheric pressure conditions,a relatively higher oxygen-enriched concentration interval(Oxy-40 to Oxy-50)under pressurized conditions is advantageous for autothermal gasification.Pressurization increases NO precursors production and also promotes homogeneous and heterogeneous reduction of NO,and provides favorable conditions for self-desulfurization.This work offers reference for the realization of a highly efficient and low-energy-consumption thermochemical treatment of livestock manure coupled with negative carbon emission technology.
基金supported by the Guangdong Major Project of Basic and Applied Basic Research(Grant No.2021B0301030001)the National Key Research and Development Program of China(Grant No.2021YFB3802300)the Foundation of National Key Laboratory of Shock Wave and Detonation Physics(Grant No.JCKYS2022212004)。
文摘The graded density impactor(GDI)dynamic loading technique is crucial for acquiring the dynamic physical property parameters of materials used in weapons.The accuracy and timeliness of GDI structural design are key to achieving controllable stress-strain rate loading.In this study,we have,for the first time,combined one-dimensional fluid computational software with machine learning methods.We first elucidated the mechanisms by which GDI structures control stress and strain rates.Subsequently,we constructed a machine learning model to create a structure-property response surface.The results show that altering the loading velocity and interlayer thickness has a pronounced regulatory effect on stress and strain rates.In contrast,the impedance distribution index and target thickness have less significant effects on stress regulation,although there is a matching relationship between target thickness and interlayer thickness.Compared with traditional design methods,the machine learning approach offers a10^(4)—10^(5)times increase in efficiency and the potential to achieve a global optimum,holding promise for guiding the design of GDI.
基金National Natural Science Foundation of China(51971103)Key Research and Development Program in Gansu Province(20YF8GA052)。
文摘A suction casting experiment was conducted on Zr_(55)Cu_(30)Al_(10)Ni_(5)(at%)amorphous alloy.Using ProCAST software,numerical simulations were performed to analyze the filling and solidification processes.The velocity field during the filling process and the temperature field during the solidification process of the alloy melt under different process parameters were obtained.Based on the simulation results,a Zr-based amorphous alloy micro-gear was prepared via casting.The results indicate that increasing the suction casting temperature enhances the fluidity of alloy melt but induces unstable flow rate during filling,which is detrimental to complete filling.Zr-based amorphous micro-gears with a module of 0.6 mm,a tooth top diameter of 8 mm,and 10 teeth were prepared through the suction casting.X-ray diffraction and differential scanning calorimetry analyses confirm that the fabricated micro-gear exhibits characteristic amorphous structural features,demonstrating well-defined geometrical contours and satisfactory forming completeness.
文摘Heat treatment processes, such as annealing and quenching, are crucial in determining residual stress evolution, microstructural changes and mechanical properties of metallic materials, with residual stresses playing a greater role in the performance of components. This paper investigates the effect of heat treatment on residual stresses induced in AISI 1025, manufactured using LENS. Finite element model was developed and simulated to analyze residual stress development. AISI 1025 samples suitable for tool and die applications in Fused Deposition Modelling (FDM) filament production, were fabricated using Laser Engineered Net Shaping (LENS) process, followed by heat treatment where annealing and quenching processes were done. The material’s microstructure, residual stress and hardness of heat-treated samples under investigation, were compared against the as-built samples. The results indicated that after annealing, tensile residual stresses were reduced by 93%, resulting in a reduced crack growth rate, compared to the as-built sample, although the hardness was reduced significantly by 25%. On the other hand, high tensile residual stresses of 425 ± 14 MPa were recorded after quenching process with an improvement of hardness by 21%.
基金financially supported by the National Natural Science Foundation of China(No.51904026)the Fundamental Research Funds for the Central Universities(No.06500108)。
文摘Hydrogen displays the potential to partially replace pulverized coal injection(PCI)in the blast furnace,and it can reduce CO_(2)emissions.In this paper,a three-dimensional mathematical model of hydrogen and pulverized coal co-injection in blast furnace tuyere was established through numerical simulation,and the effect of hydrogen injection and oxygen enrichment interaction on pulverized coal combustion and raceway smelting was investigated.The simulation results indicate that when the coal injection rate decreased from 36 to 30t/h and the hydrogen injection increased from 0 to 3600 m^(3)/h,the CO_(2)emissions decreased from 1860 to 1551 kg/t,which represents a16.6%reduction,and the pulverized coal burnout decreased from 70.1%to 63.7%.The heat released from hydrogen combustion can not only promote the volatilization of pulverized coal but also affect the combustion reaction between volatilization and oxygen,which resulted in a decrease in the temperature at the end of the raceway.Co-injection of hydrogen with PCI increased the wall temperature near the upper half part of the raceway and at the outlet of the tuyere,which required a high cooling efficiency to extend the service life of the blast furnace.The increase in oxygen level compensated for the decreased average temperature in the raceway due to hydrogen injection.The increase in the oxygen content by 3%while maintaining constant hydrogen and PCI injection rates increased the burnout and average raceway temperature by 4.2%and 43 K,respectively.The mole fraction of CO and H_(2) production increased by 0.04 and 0.02,respectively.Burnout can be improved through optimization of the particle size distribution of pulverized coal.
基金the National Natural Science Foundation of China(No.52074182)Joint Funds of the National Natural Science Foundation of China(No.U23A20612).
文摘We proposed a new technique route of directional solidification for the manufacture of super slab.A 7-t laboratory-scale thick slab was casted and characterised for trial.To further understand the process,the evolution of the multiple physical fields during the directional solidification was simulated and verified.Similar to the convectional ingot casting,a negative segregated cone of equiaxed grains was formed at the bottom,and a seriously positive segregated region was formed beneath the top surface of the slab.Specific measures on the lateral walls,base plate,and free surface were strongly recommended to ensure that the slab is relatively directionally casted.A water-cooling copper base plate accelerates the solidification rate and the columnar growth along the vertical direction.It inhibits the sedimentation of equiaxed grains and enlarges the columnar zone.Based on the simulation analysis,it can be concluded that the directional solidification technique route is promising to manufacture super slab with lower segregation level,and less porosities and inclusions.
基金co-supported by the National Natural Science Foundation of China(Nos.52105411,52105400and 52305420)the China Postdoctoral Science Foundation(No.2023M742830)Innovation Foundation for Doctor Dissertation of Northwestern Polytechnical University(No.CX2023008).
文摘In this study,a new linear friction welding(LFW)process,embedded LFW process,was put forward,which was mainly applied to combination manufacturing of long or overlong loadcarrying titanium alloy structural components in aircraft.The interfacial plastic flow behavior and bonding mechanism of this process were investigated by a developed coupling EulerianLagrangian numerical model using software ABAQUS and a novel thermo-physical simulation method with designed embedded hot compression specimen.In addition,the formation mechanism and control method of welding defects caused by uneven plastic flow were discussed.The results reveal that the plastic flow along oscillating direction of this process is even and sufficient.In the direction perpendicular to oscillation,thermo-plastic metals mainly flow downward along welding interface under coupling of shear stress and interfacial pressure,resulting in the interfacial plastic zone shown as an inverted“V”shape.The upward plastic flow in this direction is relatively weak,and only a small amount of flash is extruded from top of joint.Moreover,the wedge block and welding components at top of joint are always in un-steady friction stage,leading to nonuniform temperature field distribution and un-welded defects.According to the results of numerical simulation,high oscillating frequency combined with low pressure and small amplitude is considered as appropriate parameter selection scheme to improve the upward interfacial plastic flow at top of joint and suppress the un-welded defects.The results of thermo-physical simulation illustrate that continuous dynamic recrystallization(CDRX)induces the bonding of interface,accompanying by intense dislocation movement and creation of many low-angle grain boundaries.In the interfacial bonding area,grain orientation is random with relatively low texture density(5.0 mud)owing to CDRX.
基金supported by the Zhejiang Provincial Key Research and Development Program of China(No.2020C01020).
文摘The nozzle is a critical component responsible for generating most of the net thrust in a scramjet engine.The quality of its design directly affects the performance of the entire propulsion system.However,most turbulence models struggle to make accurate predictions for subsonic and supersonic flows in nozzles.In this study,we explored a novel model,the algebraic stress model k-kL-ARSM+J,to enhance the accuracy of turbulence numerical simulations.This new model was used to conduct numerical simulations of the design and off-design performance of a 3D supersonic asymmetric truncated nozzle designed in our laboratory,with the aim of providing a realistic pattern of changes.The research indicates that,compared to linear eddy viscosity turbulence models such as k-kL and shear stress transport(SST),the k-kL-ARSM+J algebraic stress model shows better accuracy in predicting the performance of supersonic nozzles.Its predictions were identical to the experimental values,enabling precise calculations of the nozzle.The performance trends of the nozzle are as follows:as the inlet Mach number increases,both thrust and pitching moment increase,but the rate of increase slows down.Lift peaks near the design Mach number and then rapidly decreases.With increasing inlet pressure,the nozzle thrust,lift,and pitching moment all show linear growth.As the flight altitude rises,the internal flow field within the nozzle remains relatively consistent due to the same supersonic nozzle inlet flow conditions.However,external to the nozzle,the change in external flow pressure results in the nozzle exit transitioning from over-expanded to under-expanded,leading to a shear layer behind the nozzle that initially converges towards the nozzle center and then diverges.
基金National Natural Science Foundation of China(No.52071306)the Natural Science Foundation of Shandong Province(No.ZR2019MEE050)the Natural Science Foundation of Zhejiang Province(No.LZ22E090003).
文摘The local time-stepping(LTS)algorithm is an adaptive method that adjusts the time step by selecting suitable intervals for different regions based on the spatial scale of each cell and water depth and flow velocity between cells.The method can be optimized by calculating the maximum power of two of the global time step increments in the domain,allowing the optimal time step to be approached throughout the grid.To verify the acceleration and accuracy of LTS in storm surge simulations,we developed a model to simulate astronomical storm surges along the southern coast of China.This model employs the shallow water equations as governing equations,numerical discretization using the finite volume method,and fluxes calculated by the Roe solver.By comparing the simulation results of the traditional global time-stepping algorithm with those of the LTS algorithm,we find that the latter fit the measured data better.Taking the calculation results of Typhoon Sally in 1996 as an example,we show that compared with the traditional global time-stepping algorithm,the LTS algorithm reduces computation time by 2.05 h and increases computation efficiency by 2.64 times while maintaining good accuracy.
基金supported by the key technology project of China Southern Power Grid Corporation(GZKJXM20240009).
文摘As the integration of electronic components in high-performance servers increases,heat generation significantly impacts performance and raises failure rates.Therefore,heat dissipation has become a critical concern in electronic circuit design.This study uses numerical simulations to investigate the heat dissipation characteristics of electronic components in air-cooled servers.By adjusting airflow speed,heat sink configurations,and the arrangement of straight-fin heat sinks,we optimize heat dissipation performance and analyze the mechanisms at different airflow speeds.The results show that,at the same airflow speed,the temperature of the heat sink is lower than that of the electronic components,creating a temperature gradient that enhances heat transfer.Compared to a front-to-back arrangement of two straight-fin heat sinks,placing the heat sinks parallel to each other results in a lower maximum component temperature and better temperature uniformity.Heat sinks with fins significantly improve heat dissipation.The heat sink with semicylindrical fins on the rib surface provides the best cooling performance.Moreover,compared to natural convection,the maximum temperature of the electronic components decreases by 56.17%and 61%when the incoming flow velocity is 6 m/s with two parallel flat ribbed heat sinks and front-to-back arrangement,respectively.
