BACKGROUND Percutaneous transhepatic biliary drainage(PTBD)is one of the primary clinical treatment options for patients with obstructive jaundice.In recent years,PTBD assisted by three-dimensional(3D)reconstruction t...BACKGROUND Percutaneous transhepatic biliary drainage(PTBD)is one of the primary clinical treatment options for patients with obstructive jaundice.In recent years,PTBD assisted by three-dimensional(3D)reconstruction technology has been widely implemented,but its advantages over traditional methods remains inconclusive.Thus,a discussion is warranted.AIM To explore the safety and efficacy of 3D reconstruction technology-assisted PTBD.METHODS We systematically searched the databases including the Cochrane Library,PubMed,EMBASE,Web of Science and China National Knowledge Infrastructure.The search period extended from the establishment of each database to November,2024.We screened the literature according to predefined inclusion and exclusion criteria,assessed the quality of the studies,and extracted data.Meta-analysis was performed using Revman 5.4.1 software.RESULTS A total of 15 studies were included,involving 1434 patients.The results of the meta-analysis showed that compared with the traditional group,the overall post-operative complications rate in the 3D reconstruction technology group was significantly lower[odds ratio=0.25;95%confidence interval(CI):0.17-0.36,P<0.00001].The overall puncture success rate in the 3D reconstruction group was better than those in the traditional group(odds ratio=3.61;95%CI:1.98-6.55,P<0.0001).However,there was no significant difference between the two groups in the reduction levels of postoperative total bilirubin(mean difference=-1.38;95%CI:-3.29 to 0.53,P=0.16).Subgroup analysis were conducted on the surgery time according to guidance stages of the 3D reconstruction,3D reconstruction imaging modalities,and types of studies.The results were stable,with no significant changes observed.CONCLUSION 3D reconstruction technology significantly improves the puncture success rate and safety of PTBD.However,it has no significant advantage in bile drainage effectiveness.Continued research is warranted to further explore its clinical value and optimize its application.展开更多
The core sampling experiments were conducted after hydraulic fracturing in the three-dimensional development zone of Fuling shale gas.Six coring wells of different well types were systematically designed.Based on the ...The core sampling experiments were conducted after hydraulic fracturing in the three-dimensional development zone of Fuling shale gas.Six coring wells of different well types were systematically designed.Based on the integrated engineering technology of post-fracturing drilling,coring and monitoring of shale and the analysis of fracture source tracing,the evaluation of the fracture network after fracturing in the three-dimensional development of shale gas was conducted.The data of core fractures after fracturing indicate that three major types of fractures are formed after fracturing:natural fractures,hydraulic fractures,and fractures induced by external mechanical force,which are further classified into six subcategories:natural structural fractures,natural bedding fractures,hydraulic fractures,hydraulically activated fractures,drilling induced fractures,and fractures induced by core transportation.The forms of the artificial fracture network after fracturing are complex.Hydraulic fractures and hydraulically activated fractures interweave with each other,presenting eight forms of artificial fracture networks,among which the“一”-shaped fracture is the most common,accounting for approximately 70%of the total fractures.When the distance to the fractured wellbore is less than 35 m,the density of the artificial fracture network is relatively high;when it is 35–100 m,the density is lower;and when it is beyond 100 m,the density gradually increases.The results of the fracture tracing in the core sampling area confirm that the current fracturing technology can essentially achieve the differential transformation of the reservoir in the main area of Jiaoshiba block in Fuling.The three-layer three-dimensional development model can efficiently utilize shale gas reserves,although there is still room for improvement in the complexity and propagation uniformity of fractures.It is necessary to further optimize technologies such as close-cutting combined with temporary blocking and deflection within fractures or at fracture mouths,as well as limited flow perforation techniques,to promote the balanced initiation and extension of fractures.展开更多
BACKGROUND Recently,medical three-dimensional printing technology(3DPT)has demonstrated potential benefits for the treatment of cubitus varus deformity(CVD)by improving accuracy of the osteotomy through the use of an ...BACKGROUND Recently,medical three-dimensional printing technology(3DPT)has demonstrated potential benefits for the treatment of cubitus varus deformity(CVD)by improving accuracy of the osteotomy through the use of an osteotomy guide,with or without a patient-mated plate.Here,we present an interesting CVD case,involving a patient who was treated with corrective biplanar chevron osteotomy using an innovative customized osteotomy guide and a newly designed patient-matched monoblock crosslink plate created with 3DPT.CASE SUMMARY A 32-year-old female presented with a significant CVD from childhood injury.A computer simulation was processed using images from computerized tomography scans of both upper extremities.The biplanar chevron osteotomy was designed to create identical anatomy between the mirror image of the contralateral distal humerus and the osteotomized distal humerus.Next,the customized osteotomy guide and patient-matched monoblock crosslink plate were designed and printed.A simulation osteotomy was created for the real-sized bone model,and the operation was performed using the posterior paratricipital approach with k-wire positioning from the customized osteotomy guide as a predrilled hole for screw fixation to achieve immediate control of the reduction after osteotomy.Our method allowed for successful treatment of the CVD case,significantly improving the patient’s radiographic and clinical outcomes,with satisfactory result.CONCLUSION 3DPT-created patient-matched osteotomy guide and instrumentation provides accurate control during CVD correction.展开更多
With the continuous promotion of computer technology, the application system of virtual simulation technology has been further optimized and improved, and has been widely used in various fields of social development, ...With the continuous promotion of computer technology, the application system of virtual simulation technology has been further optimized and improved, and has been widely used in various fields of social development, such as urban construction, interior design, industrial simulation and tourism teaching. China's three-dimensional animation production started relatively late, but has achieved good results with the support of related advanced technology in the process of development. Computer virtual simulation technology is an important technical support in the production of three-dimensional animation. In this paper, firstly, the related content of computer virtual simulation technology was introduced. Then, the specific application of this technology in the production of three-dimensional animation was further elaborated, so as to provide some reference for the improvement of the production effect of three-dimensional animation in the future.展开更多
Three-dimensional(3D)printing technology belongs to a new manufacturing science and has been widely used in various fields of industry.This article will apply 3D printing technology as its main research topic,with emp...Three-dimensional(3D)printing technology belongs to a new manufacturing science and has been widely used in various fields of industry.This article will apply 3D printing technology as its main research topic,with emphasis on its application in the field of medical devices and prospects for contribution.展开更多
Based on the study of the application of three-dimensional laser scanning technology in ancient building surveying and mapping,this paper briefly describes the working principle and flow of three-dimensional laser sca...Based on the study of the application of three-dimensional laser scanning technology in ancient building surveying and mapping,this paper briefly describes the working principle and flow of three-dimensional laser scanning technology.Based on the practical application,this paper puts forward the discussion of related problems and matters needing attention.This has a certain reference significance for the study of new technology in surveying and mapping of ancient buildings.展开更多
Objective To discuss the measurement of bone tumor volume on the basis of three dimensional images segmentation technology. Methods Twenty patients with lacunar bone tumor from Tianjin Hospital and Tongji Hospital wer...Objective To discuss the measurement of bone tumor volume on the basis of three dimensional images segmentation technology. Methods Twenty patients with lacunar bone tumor from Tianjin Hospital and Tongji Hospital were included in the展开更多
A new three-dimensional semi-implicit finite-volume ocean model has been developed for simulating the coastal ocean circulation, which is based on the staggered C-unstructured non-orthogonal grid in the hor- izontal d...A new three-dimensional semi-implicit finite-volume ocean model has been developed for simulating the coastal ocean circulation, which is based on the staggered C-unstructured non-orthogonal grid in the hor- izontal direction and z-level grid in the vertical direction. The three-dimensional model is discretized by the semi-implicit finite-volume method, in that the free-surface and the vertical diffusion are semi-implicit, thereby removing stability limitations associated with the surface gravity wave and vertical diffusion terms. The remaining terms in the momentum equations are discretized explicitly by an integral method. The partial cell method is used for resolving topography, which enables the model to better represent irregular topography. The model has been tested against analytical cases for wind and tidal oscillation circulation, and is applied to simulating the tidal flow in the Bohal Sea. The results are in good agreement both with the analytical solutions and measurement results.展开更多
It is a known fact that the epileptic power situation in Nigeria has become a recurring decimal. In the light of this stark reality of a country like Nigeria which is constantly plunged into pitch darkness all year ro...It is a known fact that the epileptic power situation in Nigeria has become a recurring decimal. In the light of this stark reality of a country like Nigeria which is constantly plunged into pitch darkness all year round, it has become expedient for a sustainable and urgent remedy to be sought if our country will ever think of rubbing shoulders with the economies of the world. It is this pathetic scenario, we find ourselves in that it has given rise to this paper which tends to review possible ways and means of redressing the ugly trend. This paper examines the prospects and possible applications of Smart Grid Technology (SGT) to the Nigeria Power System. Nigeria Power System consists of 28 buses, 32 Transmission lines and 10 generating stations, with a view to reduce the high active and reactive transmission losses. The study shows that smart grid system will make the present network more efficient and reliable by connecting different sources of distributed generators into the existing grid. Basic requirements necessary for the application of SGT using the Nigeria Power System as a case study were discussed.展开更多
The development of minimally invasive surgery has transformed the management of gastrointestinal cancer.Notably,three-dimensional visualization systems have increased surgical precision.This editorial discusses a rece...The development of minimally invasive surgery has transformed the management of gastrointestinal cancer.Notably,three-dimensional visualization systems have increased surgical precision.This editorial discusses a recent study by Shen and Zhang,which compared the clinical applications of naked-eye threedimensional laparoscopic systems vs traditional optical systems in radical surgery for gastric and colorectal cancer.Both systems appeared to yield comparable surgical and oncological outcomes in terms of safety parameters,operating times,and quality of lymph node dissection.However,the spectacle-free system’s technical and logistical limitations hindered its effects on the surgical team’s overall competency.This editorial examines the authors’findings within the broader context of the evolution of oncologic laparoscopy,discusses the relevance of the results in light of the current literature,and proposes future research directions focused on multicenter validation,comprehensive ergonomic analysis,and technological advancements aimed at enhancing intraoperative collaboration.As technology continues to evolve,clinical implementation of new methods must be supported by robust scientific evidence and standardized criteria,to ensure tangible improvements in efficiency,safety,and oncologic outcomes.展开更多
By coupling the three-dimensional hydrodynamic model with the wave model, numerical simulations of the three- dimensional wave-induced current are carried out in this study. The wave model is based on the numerical so...By coupling the three-dimensional hydrodynamic model with the wave model, numerical simulations of the three- dimensional wave-induced current are carried out in this study. The wave model is based on the numerical solution of the modified wave action equation and eikonal equation, which can describe the wave refraction and diffraction. The hydrodynamic model is driven by the wave-induced radiation stresses and affected by the wave turbulence. The numerical implementation of the module has used the finite-volume schemes on unstructured grid, which provides great flexibility for modeling the waves and currents in the complex actual nearshore, and ensures the conservation of energy propagation. The applicability of the proposed model is evaluated in calculating the cases of wave set-up, longshore currents, undertow on a sloping beach, rip currents and meandering longshore currents on a tri-cuspate beach. The results indicate that it is necessary to introduce the depth-dependent radiation stresses into the numerical simulation of wave-induced currents, and comparisons show that the present model makes better prediction on the wave procedure as well as both horizontal and vertical structures in the wave-induced current field.展开更多
To solve the topology optimization of complicated multi-objective continuous/discrete design variables in aircmit structure design, a Parallel Pareto Genetic Algorithm （PPGA） is presented based on grid platform in t...To solve the topology optimization of complicated multi-objective continuous/discrete design variables in aircmit structure design, a Parallel Pareto Genetic Algorithm （PPGA） is presented based on grid platform in this paper. In the algorithm, the commercial finite element analysis （FEA） software is integrated as the calculating tool for analyzing the objective functions and the filter of Pareto solution set based on weight information is introduced to deal with the relationships among all objectives. Grid technology is utilized in PPGA to realize the distributed computations and the user interface is developed to realize the job submission and job management locally/remotely. Taking the aero-elastic tailoring of a composite wing for optimization as an example, a set of Pareto solutions are obtained for the decision-maker. The numerical results show that the aileron reversal problem can be solved by adding the limited skin weight in this system. The algorithm can be used to solve complicated topology optimization for composite structures in engineering and the computation efficiency can be improved greatly by using the grid platform that aggregates numerous idle resources.展开更多
Ocean temperature is an important physical variable in marine ecosystems,and ocean temperature prediction is an important research objective in ocean-related fields.Currently,one of the commonly used methods for ocean...Ocean temperature is an important physical variable in marine ecosystems,and ocean temperature prediction is an important research objective in ocean-related fields.Currently,one of the commonly used methods for ocean temperature prediction is based on data-driven,but research on this method is mostly limited to the sea surface,with few studies on the prediction of internal ocean temperature.Existing graph neural network-based methods usually use predefined graphs or learned static graphs,which cannot capture the dynamic associations among data.In this study,we propose a novel dynamic spatiotemporal graph neural network(DSTGN)to predict threedimensional ocean temperature(3D-OT),which combines static graph learning and dynamic graph learning to automatically mine two unknown dependencies between sequences based on the original 3D-OT data without prior knowledge.Temporal and spatial dependencies in the time series were then captured using temporal and graph convolutions.We also integrated dynamic graph learning,static graph learning,graph convolution,and temporal convolution into an end-to-end framework for 3D-OT prediction using time-series grid data.In this study,we conducted prediction experiments using high-resolution 3D-OT from the Copernicus global ocean physical reanalysis,with data covering the vertical variation of temperature from the sea surface to 1000 m below the sea surface.We compared five mainstream models that are commonly used for ocean temperature prediction,and the results showed that the method achieved the best prediction results at all prediction scales.展开更多
Submission Deadline： 15 October 2010The electric industry is being transformed from a centralized network to one that is less centralized and allows more consumer interaction in the form of a smart grid. A smart grid...Submission Deadline： 15 October 2010The electric industry is being transformed from a centralized network to one that is less centralized and allows more consumer interaction in the form of a smart grid. A smart grid is a power transmission and distribution network that can incorporate millions of sensors all connected through an advanced, two-way communications and data acquisition system to provide real-time monitoring, diagnosis and control. Smart grid enables more efficient, reliable and secure energy service, facilitate grid-integration of renewable systems and energy storage, and better routing of power and demand management. The move to a smarter grid promises to change the industry＇s entire business model and its relationship with all stakeholders, involving and affecting power companies, regulators, energy service providers, technology and automation vendors, and all consumers of electric power.展开更多
To reduce the computing time of composite computer-generated holograms （CGHs） gen- eration based upon the angular projection algorithm for holographic three-dimensional （3D） display, a grid-based holographic displ...To reduce the computing time of composite computer-generated holograms （CGHs） gen- eration based upon the angular projection algorithm for holographic three-dimensional （3D） display, a grid-based holographic display （ GHD ） scheme was designed. The grid computing technology was applied to numerically process the different angular projections of an object in distributed-parallel manner to create the corresponding CGHs. The whole treatment of a projection was regarded as a job executed on the grid node machine. The number of jobs which were submitted to grid nodes, therefore, was equal to that of the projections of the object. A Condor-based grid testbed was constructed to verify the feasibility of the GHD scheme, and a graphical user interface （GUI） program and several service modules were developed for it. A 3D terrain model as an example was processed on the testbed. The result showed that the scheme was feasible and able to improve the execution elficiency greatly.展开更多
In Taiwan, in corresponding to the policy of reducing CO2 emission, reforming current energy structure, and saving energy, the National Energy Program (NEP)-Smart Grid General Project Phase 1 was implemented. The obje...In Taiwan, in corresponding to the policy of reducing CO2 emission, reforming current energy structure, and saving energy, the National Energy Program (NEP)-Smart Grid General Project Phase 1 was implemented. The objectives of this project are meant to enhance the robustness of the power grid, reduce greenhouse gas emission, increase the penetration rate of renewable energy and develop smart grid industry in Taiwan. This study will introduce the positioning of the Smart Grid General Project among overall smart grid development, the results of Phase 1, the smart grid technology commercialization process of Phase 2, and the promotion model with collaboration between industry, universities and research units.展开更多
Nowadays, the global climate is undergoing great changes, the global population is increasing and the energy problem is becoming more and more serious, so the construction of smart grid has attracted global attention....Nowadays, the global climate is undergoing great changes, the global population is increasing and the energy problem is becoming more and more serious, so the construction of smart grid has attracted global attention. At present, the main goal of domestic power grid companies is to combine the strong grid structure with intelligent construction. The system mainly includes power generation technology, communication technology, automatic regulation technology, etc.展开更多
The traditional computed tomography(CT)reconstruction methods are noisy,low resolution,poor contrast,and generally not suitable to detect the smaller flaws.Besides,the filter design is also difficult.The CT characteri...The traditional computed tomography(CT)reconstruction methods are noisy,low resolution,poor contrast,and generally not suitable to detect the smaller flaws.Besides,the filter design is also difficult.The CT characteristics reconstruction technology was brought forward to improve in these aspects,which is defined to directly reconstruct the characteristics of the projection for the best requirements not the overall image quality.The two-dimension(2D)and three-dimension(3D)CT characteristics reconstruction algorithm were firstly introduced,then by detailed analysis,experimental results and comparsion of parameters calculated,its advantages in keeping better high-frequency feature,better noise immunity,short time-consuming and easier design are verified.展开更多
In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently,which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor...In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently,which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure(EWP). By means of a threedimensional(3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system(TDS) widely used in China and its optimized drainage system(ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice,including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 k Pa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.展开更多
基金Supported by the Natural Science Foundation of Fujian Province,No.2022J011442.
文摘BACKGROUND Percutaneous transhepatic biliary drainage(PTBD)is one of the primary clinical treatment options for patients with obstructive jaundice.In recent years,PTBD assisted by three-dimensional(3D)reconstruction technology has been widely implemented,but its advantages over traditional methods remains inconclusive.Thus,a discussion is warranted.AIM To explore the safety and efficacy of 3D reconstruction technology-assisted PTBD.METHODS We systematically searched the databases including the Cochrane Library,PubMed,EMBASE,Web of Science and China National Knowledge Infrastructure.The search period extended from the establishment of each database to November,2024.We screened the literature according to predefined inclusion and exclusion criteria,assessed the quality of the studies,and extracted data.Meta-analysis was performed using Revman 5.4.1 software.RESULTS A total of 15 studies were included,involving 1434 patients.The results of the meta-analysis showed that compared with the traditional group,the overall post-operative complications rate in the 3D reconstruction technology group was significantly lower[odds ratio=0.25;95%confidence interval(CI):0.17-0.36,P<0.00001].The overall puncture success rate in the 3D reconstruction group was better than those in the traditional group(odds ratio=3.61;95%CI:1.98-6.55,P<0.0001).However,there was no significant difference between the two groups in the reduction levels of postoperative total bilirubin(mean difference=-1.38;95%CI:-3.29 to 0.53,P=0.16).Subgroup analysis were conducted on the surgery time according to guidance stages of the 3D reconstruction,3D reconstruction imaging modalities,and types of studies.The results were stable,with no significant changes observed.CONCLUSION 3D reconstruction technology significantly improves the puncture success rate and safety of PTBD.However,it has no significant advantage in bile drainage effectiveness.Continued research is warranted to further explore its clinical value and optimize its application.
文摘The core sampling experiments were conducted after hydraulic fracturing in the three-dimensional development zone of Fuling shale gas.Six coring wells of different well types were systematically designed.Based on the integrated engineering technology of post-fracturing drilling,coring and monitoring of shale and the analysis of fracture source tracing,the evaluation of the fracture network after fracturing in the three-dimensional development of shale gas was conducted.The data of core fractures after fracturing indicate that three major types of fractures are formed after fracturing:natural fractures,hydraulic fractures,and fractures induced by external mechanical force,which are further classified into six subcategories:natural structural fractures,natural bedding fractures,hydraulic fractures,hydraulically activated fractures,drilling induced fractures,and fractures induced by core transportation.The forms of the artificial fracture network after fracturing are complex.Hydraulic fractures and hydraulically activated fractures interweave with each other,presenting eight forms of artificial fracture networks,among which the“一”-shaped fracture is the most common,accounting for approximately 70%of the total fractures.When the distance to the fractured wellbore is less than 35 m,the density of the artificial fracture network is relatively high;when it is 35–100 m,the density is lower;and when it is beyond 100 m,the density gradually increases.The results of the fracture tracing in the core sampling area confirm that the current fracturing technology can essentially achieve the differential transformation of the reservoir in the main area of Jiaoshiba block in Fuling.The three-layer three-dimensional development model can efficiently utilize shale gas reserves,although there is still room for improvement in the complexity and propagation uniformity of fractures.It is necessary to further optimize technologies such as close-cutting combined with temporary blocking and deflection within fractures or at fracture mouths,as well as limited flow perforation techniques,to promote the balanced initiation and extension of fractures.
文摘BACKGROUND Recently,medical three-dimensional printing technology(3DPT)has demonstrated potential benefits for the treatment of cubitus varus deformity(CVD)by improving accuracy of the osteotomy through the use of an osteotomy guide,with or without a patient-mated plate.Here,we present an interesting CVD case,involving a patient who was treated with corrective biplanar chevron osteotomy using an innovative customized osteotomy guide and a newly designed patient-matched monoblock crosslink plate created with 3DPT.CASE SUMMARY A 32-year-old female presented with a significant CVD from childhood injury.A computer simulation was processed using images from computerized tomography scans of both upper extremities.The biplanar chevron osteotomy was designed to create identical anatomy between the mirror image of the contralateral distal humerus and the osteotomized distal humerus.Next,the customized osteotomy guide and patient-matched monoblock crosslink plate were designed and printed.A simulation osteotomy was created for the real-sized bone model,and the operation was performed using the posterior paratricipital approach with k-wire positioning from the customized osteotomy guide as a predrilled hole for screw fixation to achieve immediate control of the reduction after osteotomy.Our method allowed for successful treatment of the CVD case,significantly improving the patient’s radiographic and clinical outcomes,with satisfactory result.CONCLUSION 3DPT-created patient-matched osteotomy guide and instrumentation provides accurate control during CVD correction.
文摘With the continuous promotion of computer technology, the application system of virtual simulation technology has been further optimized and improved, and has been widely used in various fields of social development, such as urban construction, interior design, industrial simulation and tourism teaching. China's three-dimensional animation production started relatively late, but has achieved good results with the support of related advanced technology in the process of development. Computer virtual simulation technology is an important technical support in the production of three-dimensional animation. In this paper, firstly, the related content of computer virtual simulation technology was introduced. Then, the specific application of this technology in the production of three-dimensional animation was further elaborated, so as to provide some reference for the improvement of the production effect of three-dimensional animation in the future.
文摘Three-dimensional(3D)printing technology belongs to a new manufacturing science and has been widely used in various fields of industry.This article will apply 3D printing technology as its main research topic,with emphasis on its application in the field of medical devices and prospects for contribution.
基金Jiangxi Social Science Planning Project:Research on the Activation of Traditional Villages in Jiangxi Province from the Perspective of Cultural Conservation:A Case Study of Fuhe River Basin(Grant No.17BJ16).
文摘Based on the study of the application of three-dimensional laser scanning technology in ancient building surveying and mapping,this paper briefly describes the working principle and flow of three-dimensional laser scanning technology.Based on the practical application,this paper puts forward the discussion of related problems and matters needing attention.This has a certain reference significance for the study of new technology in surveying and mapping of ancient buildings.
文摘Objective To discuss the measurement of bone tumor volume on the basis of three dimensional images segmentation technology. Methods Twenty patients with lacunar bone tumor from Tianjin Hospital and Tongji Hospital were included in the
基金The Major State Basic Research Program of China under contract No. 2012CB417002the National Natural Science Foundation of China under contract Nos 50909065 and 51109039
文摘A new three-dimensional semi-implicit finite-volume ocean model has been developed for simulating the coastal ocean circulation, which is based on the staggered C-unstructured non-orthogonal grid in the hor- izontal direction and z-level grid in the vertical direction. The three-dimensional model is discretized by the semi-implicit finite-volume method, in that the free-surface and the vertical diffusion are semi-implicit, thereby removing stability limitations associated with the surface gravity wave and vertical diffusion terms. The remaining terms in the momentum equations are discretized explicitly by an integral method. The partial cell method is used for resolving topography, which enables the model to better represent irregular topography. The model has been tested against analytical cases for wind and tidal oscillation circulation, and is applied to simulating the tidal flow in the Bohal Sea. The results are in good agreement both with the analytical solutions and measurement results.
文摘It is a known fact that the epileptic power situation in Nigeria has become a recurring decimal. In the light of this stark reality of a country like Nigeria which is constantly plunged into pitch darkness all year round, it has become expedient for a sustainable and urgent remedy to be sought if our country will ever think of rubbing shoulders with the economies of the world. It is this pathetic scenario, we find ourselves in that it has given rise to this paper which tends to review possible ways and means of redressing the ugly trend. This paper examines the prospects and possible applications of Smart Grid Technology (SGT) to the Nigeria Power System. Nigeria Power System consists of 28 buses, 32 Transmission lines and 10 generating stations, with a view to reduce the high active and reactive transmission losses. The study shows that smart grid system will make the present network more efficient and reliable by connecting different sources of distributed generators into the existing grid. Basic requirements necessary for the application of SGT using the Nigeria Power System as a case study were discussed.
文摘The development of minimally invasive surgery has transformed the management of gastrointestinal cancer.Notably,three-dimensional visualization systems have increased surgical precision.This editorial discusses a recent study by Shen and Zhang,which compared the clinical applications of naked-eye threedimensional laparoscopic systems vs traditional optical systems in radical surgery for gastric and colorectal cancer.Both systems appeared to yield comparable surgical and oncological outcomes in terms of safety parameters,operating times,and quality of lymph node dissection.However,the spectacle-free system’s technical and logistical limitations hindered its effects on the surgical team’s overall competency.This editorial examines the authors’findings within the broader context of the evolution of oncologic laparoscopy,discusses the relevance of the results in light of the current literature,and proposes future research directions focused on multicenter validation,comprehensive ergonomic analysis,and technological advancements aimed at enhancing intraoperative collaboration.As technology continues to evolve,clinical implementation of new methods must be supported by robust scientific evidence and standardized criteria,to ensure tangible improvements in efficiency,safety,and oncologic outcomes.
基金financially supported by the the National Natural Science Foundation of China(Grant No.51709054)the Public Science and Technology Research Funds Projects of Ocean(Grant Nos.201405025 and 201505019)
文摘By coupling the three-dimensional hydrodynamic model with the wave model, numerical simulations of the three- dimensional wave-induced current are carried out in this study. The wave model is based on the numerical solution of the modified wave action equation and eikonal equation, which can describe the wave refraction and diffraction. The hydrodynamic model is driven by the wave-induced radiation stresses and affected by the wave turbulence. The numerical implementation of the module has used the finite-volume schemes on unstructured grid, which provides great flexibility for modeling the waves and currents in the complex actual nearshore, and ensures the conservation of energy propagation. The applicability of the proposed model is evaluated in calculating the cases of wave set-up, longshore currents, undertow on a sloping beach, rip currents and meandering longshore currents on a tri-cuspate beach. The results indicate that it is necessary to introduce the depth-dependent radiation stresses into the numerical simulation of wave-induced currents, and comparisons show that the present model makes better prediction on the wave procedure as well as both horizontal and vertical structures in the wave-induced current field.
文摘To solve the topology optimization of complicated multi-objective continuous/discrete design variables in aircmit structure design, a Parallel Pareto Genetic Algorithm （PPGA） is presented based on grid platform in this paper. In the algorithm, the commercial finite element analysis （FEA） software is integrated as the calculating tool for analyzing the objective functions and the filter of Pareto solution set based on weight information is introduced to deal with the relationships among all objectives. Grid technology is utilized in PPGA to realize the distributed computations and the user interface is developed to realize the job submission and job management locally/remotely. Taking the aero-elastic tailoring of a composite wing for optimization as an example, a set of Pareto solutions are obtained for the decision-maker. The numerical results show that the aileron reversal problem can be solved by adding the limited skin weight in this system. The algorithm can be used to solve complicated topology optimization for composite structures in engineering and the computation efficiency can be improved greatly by using the grid platform that aggregates numerous idle resources.
基金The National Key R&D Program of China under contract No.2021YFC3101603.
文摘Ocean temperature is an important physical variable in marine ecosystems,and ocean temperature prediction is an important research objective in ocean-related fields.Currently,one of the commonly used methods for ocean temperature prediction is based on data-driven,but research on this method is mostly limited to the sea surface,with few studies on the prediction of internal ocean temperature.Existing graph neural network-based methods usually use predefined graphs or learned static graphs,which cannot capture the dynamic associations among data.In this study,we propose a novel dynamic spatiotemporal graph neural network(DSTGN)to predict threedimensional ocean temperature(3D-OT),which combines static graph learning and dynamic graph learning to automatically mine two unknown dependencies between sequences based on the original 3D-OT data without prior knowledge.Temporal and spatial dependencies in the time series were then captured using temporal and graph convolutions.We also integrated dynamic graph learning,static graph learning,graph convolution,and temporal convolution into an end-to-end framework for 3D-OT prediction using time-series grid data.In this study,we conducted prediction experiments using high-resolution 3D-OT from the Copernicus global ocean physical reanalysis,with data covering the vertical variation of temperature from the sea surface to 1000 m below the sea surface.We compared five mainstream models that are commonly used for ocean temperature prediction,and the results showed that the method achieved the best prediction results at all prediction scales.
文摘Submission Deadline： 15 October 2010The electric industry is being transformed from a centralized network to one that is less centralized and allows more consumer interaction in the form of a smart grid. A smart grid is a power transmission and distribution network that can incorporate millions of sensors all connected through an advanced, two-way communications and data acquisition system to provide real-time monitoring, diagnosis and control. Smart grid enables more efficient, reliable and secure energy service, facilitate grid-integration of renewable systems and energy storage, and better routing of power and demand management. The move to a smarter grid promises to change the industry＇s entire business model and its relationship with all stakeholders, involving and affecting power companies, regulators, energy service providers, technology and automation vendors, and all consumers of electric power.
文摘To reduce the computing time of composite computer-generated holograms （CGHs） gen- eration based upon the angular projection algorithm for holographic three-dimensional （3D） display, a grid-based holographic display （ GHD ） scheme was designed. The grid computing technology was applied to numerically process the different angular projections of an object in distributed-parallel manner to create the corresponding CGHs. The whole treatment of a projection was regarded as a job executed on the grid node machine. The number of jobs which were submitted to grid nodes, therefore, was equal to that of the projections of the object. A Condor-based grid testbed was constructed to verify the feasibility of the GHD scheme, and a graphical user interface （GUI） program and several service modules were developed for it. A 3D terrain model as an example was processed on the testbed. The result showed that the scheme was feasible and able to improve the execution elficiency greatly.
文摘In Taiwan, in corresponding to the policy of reducing CO2 emission, reforming current energy structure, and saving energy, the National Energy Program (NEP)-Smart Grid General Project Phase 1 was implemented. The objectives of this project are meant to enhance the robustness of the power grid, reduce greenhouse gas emission, increase the penetration rate of renewable energy and develop smart grid industry in Taiwan. This study will introduce the positioning of the Smart Grid General Project among overall smart grid development, the results of Phase 1, the smart grid technology commercialization process of Phase 2, and the promotion model with collaboration between industry, universities and research units.
文摘Nowadays, the global climate is undergoing great changes, the global population is increasing and the energy problem is becoming more and more serious, so the construction of smart grid has attracted global attention. At present, the main goal of domestic power grid companies is to combine the strong grid structure with intelligent construction. The system mainly includes power generation technology, communication technology, automatic regulation technology, etc.
基金National Natural Science Foundation of China(No.61471325)
文摘The traditional computed tomography(CT)reconstruction methods are noisy,low resolution,poor contrast,and generally not suitable to detect the smaller flaws.Besides,the filter design is also difficult.The CT characteristics reconstruction technology was brought forward to improve in these aspects,which is defined to directly reconstruct the characteristics of the projection for the best requirements not the overall image quality.The two-dimension(2D)and three-dimension(3D)CT characteristics reconstruction algorithm were firstly introduced,then by detailed analysis,experimental results and comparsion of parameters calculated,its advantages in keeping better high-frequency feature,better noise immunity,short time-consuming and easier design are verified.
基金supported by the National Natural Science Foundation of China (Grant No. U1934211)the Open Foundation of National Engineering Research Center of High-speed Railway Construction Technology (Grant No. HSR202005)Scientific Research Project of Hunan Education Department (Grant No.20B596)。
文摘In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently,which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure(EWP). By means of a threedimensional(3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system(TDS) widely used in China and its optimized drainage system(ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice,including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 k Pa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.
