Reasonable design and applications of graphene-based materials are supposed to be promising ways to tackle many fundamental problems emerging in lithium batteries,including suppression of electrode/electrolyte side re...Reasonable design and applications of graphene-based materials are supposed to be promising ways to tackle many fundamental problems emerging in lithium batteries,including suppression of electrode/electrolyte side reactions,stabilization of electrode architecture,and improvement of conductive component.Therefore,extensive fundamental research on this aspect has been performed so far.However,when it comes to large-scale industrial applications,the utilization of graphene-based materials progresses at a very slow pace.Namely,there presents a severe technological decoupling between academic research and industrial application,and there is an urgent need to link them.Herein,in order to address current issues of graphene-based materials used in lithium batteries,we present their latest advancements with stateof-the-art technologies.Potential applications of graphenebased materials in practical lithium batteries are highlighted and predicted to bridge the gap between the academic progress and industrial manufacture,thereby paving the way for accelerating the development of graphenebased material as well as lithium battery industry.展开更多
Two reported three-dimensional covalent organic frameworks(3D-COFs),COF-300 and COF-301,which have hierarchical porous structures and large pore volumes,were synthesized and employed as host materials for lithium-sulf...Two reported three-dimensional covalent organic frameworks(3D-COFs),COF-300 and COF-301,which have hierarchical porous structures and large pore volumes,were synthesized and employed as host materials for lithium-sulfur batteries.Owing to possessing excellent porosities as well as abundant hydroxyl groups in the pore walls,COF-301 can not only trap lithium polysulfides(PSs)via physical adsorption inside the pores,but also capture PSs by chemical interactions to relieve the shuttle effect.Interestingly,it is the first time that 3D-COFs were utilized as host materials for lithium-sulfur batteries as well as hydroxyl groups were introduced into COFs for improving the battery performance.As a result,COF-301@S as cathode material could reserve the capacity of 411.6 mA·h·g^-1 after 500 cycles with only 0.081%fading per cycle at 0.5 C,exhibiting better battery performance compared with COF-300@S.This study not only expands the applications of 3D-COFs but also provides a new route for designing lithium-sulfur batteries.展开更多
The three-dimensional ordered macroporous CeO2：Yb,Er materials were prepared, and the influence of doping concentra- tion of Yb3＋ or Er3＋ ions on upconversion property was investigated. Green and red upconversion e...The three-dimensional ordered macroporous CeO2：Yb,Er materials were prepared, and the influence of doping concentra- tion of Yb3＋ or Er3＋ ions on upconversion property was investigated. Green and red upconversion emissions were observed under the excitation of 980 nm at room temperature. It was found that the ratio of red to green upconversion emission intensity increased with increasing of concentration of the Yb3＋ or Er3＋ ions in the three-dimensional ordered macroporous CeO2：Yb,Er materials. When the concentration of Yb3＋ was 10 mol%, pure red upconversion emission was obtained. The varied mechanism of ratio of red to green upconversion emission intensity was discussed with the concentration of Yb3＋ or Er3＋ ions.展开更多
Damage indices are effective in quantifying structural seismic damage.Numerous response-based damage indices have been developed and validated through the hysteretic response of various experimental specimens.However,...Damage indices are effective in quantifying structural seismic damage.Numerous response-based damage indices have been developed and validated through the hysteretic response of various experimental specimens.However,the accuracy of these indices for evaluating damage of RC columns is challenged by fluctuating axial load and irregular horizontal loading paths from 3-D earthquake excitations.This study introduces D_(iem),a material-based damage model for RC columns under random bidirectional loads and variable axial forces.Section damage indices of the plastic hinge are calculated by integrating the damage indices of concrete and steel fiber elements,considering their distance to the centroid axis.The P-Δeffect index is defined,and the component failure index is calculated using a combination of these indices.A hysteretic simulation and D_(iem)damage analysis program for cantilever RC columns is developed using Fortran.Three RC columns tested under bidirectional hysteretic loading are simulated to calibrate the program.Parameter analysis of 1,638 RC columns is conducted to verify D_(iem)’s applicability.The results demonstrated that D_(iem)’s failure assessment aligns with the 80%residual criterion.D_(iem)analysis of a real seismic damaged RC column shows satisfactory agreement with post-earthquake damage assessment and illustrates significant damage differences between columns with and without axial load fluctuation.展开更多
An orthotropic functionally graded piezoelectric rectangular plate with arbitrarily distributed material properties was studied, which is simply supported and grounded（electrically） on its four lateral edges. The st...An orthotropic functionally graded piezoelectric rectangular plate with arbitrarily distributed material properties was studied, which is simply supported and grounded（electrically） on its four lateral edges. The state equations of the functionally graded piezoelectric material were obtained using the state-space approach, and a Peano-Baker series solution was obtained for the coupled electroelastic fi elds of the functionally graded piezoelectric plate subjected to mechanical and electric loading on its upper and lower surfaces. The influence of different distributions of material properties on the structural response of the plate was studied using the obtained solutions.展开更多
Three-dimensional（3D）ordered mesoporous MnO2 was prepared using KIT-6 mesoporous molecular sieves as a hard template.The material was used for catalytic oxidation of HCHO.The material has high surface areas and the ...Three-dimensional（3D）ordered mesoporous MnO2 was prepared using KIT-6 mesoporous molecular sieves as a hard template.The material was used for catalytic oxidation of HCHO.The material has high surface areas and the mesoporous characteristics of the template,with cubic symmetry（ia3d）.It consists of a β-MnO2 crystalline phase corresponding to pyrolusite,with a rutile structure.Transmission electron microscopy and X-ray photoelectron spectroscopy showed that the 3D-MnO2 catalyst has a large number of exposed Mn4＋ ions on the（110）crystal plane surfaces,with a lattice spacing of 0.311 nm; this enhances oxidation of HCHO.Complete conversion of HCHO to CO2 and H2O was achieved at 130 °C on 3D-MnO2; the same conversions on α-MnO2 and β-MnO2 nanorods were obtained at 140 and 180 °C,respectively,under the same conditions.The specific mesoporous structure,high specific surface area,and large number of surface Mn4＋ ions are responsible for the catalytic activity of 3D-MnO2 in HCHO oxidation.展开更多
Arc erosion morphologies of Ag/MeO（10） electrical contact materials after 50000 operations under direct current of 19 V and 20 A and resistive load conditions were investigated using scanning electron microscope（SE...Arc erosion morphologies of Ag/MeO（10） electrical contact materials after 50000 operations under direct current of 19 V and 20 A and resistive load conditions were investigated using scanning electron microscope（SEM） and a 3D optical profiler（3DOP）. The results indicated that 3DOP could supply clearer and more detailed arc erosion morphology information. Arc erosion resistance of Ag/SnO_2（10） electrical contact material was the best and that of Ag/CuO（10） was the worst. Arc erosion morphology of Ag/MeO（10） electrical contact materials mainly included three different types. Arc erosion morphologies of Ag/ZnO（10） and Ag/SnO_2（10） electrical contact materials were mainly liquid splash and evaporation, and those of Ag/CuO（10） and Ag/CdO（10） were mainly material transfer from anode to cathode. Arc erosion morphology of Ag/SnO_2（6）In_2O_3（4） electrical contact materials included both liquid splash, evaporation and material transfer. In addition, the formation process and mechanism on arc erosion morphology of Ag/MeO（10） electrical contact materials were discussed.展开更多
Three-dimensional ordered macroporous (3DOM) La1?xKxNiO3 perovskite-type catalysts were successfully prepared by a colloidal crystal template method and characterized by scanning electron microscopy, transmission elec...Three-dimensional ordered macroporous (3DOM) La1?xKxNiO3 perovskite-type catalysts were successfully prepared by a colloidal crystal template method and characterized by scanning electron microscopy, transmission electron microscopy, high-resolution transmission electron microscopy, energy-dispersive X-ray scattering elemental mapping, X-ray diffraction, Raman and X-ray photoelectron spectroscopy, and temperature-programmed reduction of H2. Further, their catalytic activity in soot combustion was determined by temperature-programmed oxidation reaction. K substitution into the LaNiO3 lattice led to remarkably improved catalytic activity of this catalyst in soot combustion. Amongst various catalysts, La0.95K0.05NiO3 exhibited the highest activity in soot combustion (with its T50 and CO2 S values being 338 °C and 98.2%, respectively), which is comparable to the catalytic activities of Pt-based catalysts under the condition of poor contact between the soot and the catalyst. K-substitution improves the valence state of Ni and increases the number of oxygen vacancies, thereby leading to increased density of surface-active oxygen species. The active oxygen species play a vital role in catalyzing the elimination of soot. The perovskite-type La1?xKxNiO3 nanocatalysts with 3DOM structure without noble metals have potential for practical applications in the catalytic combustion of diesel soot particles.展开更多
As a two-dimensional(2D)material,graphene shows excellent advantages in the field of gas sensors due to its inherent large specific surface area and unique electrical properties.However,in the practical application of...As a two-dimensional(2D)material,graphene shows excellent advantages in the field of gas sensors due to its inherent large specific surface area and unique electrical properties.However,in the practical application of gas detection,graphene sheet is easy to form irreversible agglomeration and has some limitations such as low sensitivity,long response time and slow recovery speed,which greatly reduce its gas sensing performance.As a gas sensing material,three-dimensional(3D)porous graphene has been extensively studied in recent years owing to its larger specific surface area and stable structure.In order to synthesize graphene with different three-dimensional structures,many methods have been developed.Herein,the synthesis and assembly of three-dimensional graphene and its composites were reviewed,with emphasis on the application of three-dimensional graphene and its composites in the field of gas sensors.The challenges and development prospects of three-dimensional graphene materials in the application of gas sensors were briefly described.展开更多
Three-dimensional(3D)functional graphenebased architecture with superior electrical conductivity and good mechanical strength has promising applications in energy storage and electrics.Viscoelasticity-adjustable inks ...Three-dimensional(3D)functional graphenebased architecture with superior electrical conductivity and good mechanical strength has promising applications in energy storage and electrics.Viscoelasticity-adjustable inks make it possible to achieve desired 3D architectures with interconnected and continuous interior networks by microextrusion printing.In this work,ultra-low-concentration graphene oxide(GO)inks of~15 mg·ml-1 have been obtained and demonstrated in direct 3D printing with a facile cross-linking(direct ink writing).The rheological behavior of the GO strategy by cations,which is the lowest concentration to achieve direct ink writing inks,could be adjusted from 1×10^(4) to 1×10^(5) Pa·s^(-1) with different concentrations of cations due to strong cross-linking networks between GO sheets and cations.Meanwhile,the specific strength and electrical conductivity of 3D-printed graphene architecture are notably enhanced,reaching up to 51.7×10^(3) N·m·kg^(-1)and 119 S·m^(-1),which are superior to conventional graphene aerogels.Furthermore,3D printing graphene-based architecture assembled in micro-superc apacitor exhibits excellent electrochemical performance,which can be ascribed to the effective ion transportation through the interconnected networks.The strategy demonstrated is useful in the design of complex-shaped,graphene-based architectures for scalable manufacturing of practical energy storage applications.展开更多
A three-dimensional analysis of a simply-supported functionally graded rectangular plate with an arbitrary distribution of material properties is made using a simple and effective method based on the Haar wavelet. Wit...A three-dimensional analysis of a simply-supported functionally graded rectangular plate with an arbitrary distribution of material properties is made using a simple and effective method based on the Haar wavelet. With good features in treating singularities, Haar series solution converges rapidly for arbitrary distributions, especially for the case where the material properties change rapidly in some regions. Through numerical examples the influences of the ratio of material constants on the top and bottom surfaces and different material gradient distributions on the structural response of the plate to mechanical stimuli are studied.展开更多
The use of three-dimensional(3D)electrodes in water treatment is competitive because of their high catalytic efficiency,low energy consumption and promising development.The use of particle electrodes is a key research...The use of three-dimensional(3D)electrodes in water treatment is competitive because of their high catalytic efficiency,low energy consumption and promising development.The use of particle electrodes is a key research focus in this technology.They are usually in the form of particles that fill the space between the cathode and anode,and the selection of materials used is important.Carbon-based materials are widely used because of their large specific surface area,good adsorption performance,high chemical stability and low cost.The principles of 3D electrode technology are introduced and recent research on its use for degrading organic pollutants using carbon-based particle electrodes is summarized.The classification of particle electrodes is introduced and the challenges for the future development of carbon-based particle electrodes in wastewater treatment are discussed.展开更多
Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal...Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal mechanisms(MRMs)involved in the machining of PRMMCs.This paper develops a three-dimensional(3D)microstructure-based model for investigating the MRM and surface integrity of machined PRMMCs.To accurately mimic the actual microstructure of a PRMMC,polyhedrons were randomly distributed inside the matrix to represent irregular SiC particles.Particle fracture and matrix deformation and failure were taken into account.For the model’s capability comparison,a two-dimensional(2D)analysis was also conducted.Relevant cutting experiments showed that the established 3D model accurately predicted the material removal,chip morphology,machined surface finish,and cutting forces.It was found that the matrix-particle-tool interactions led to particle fractures,mainly in the primary shear and secondary deformation zones along the cutting path and beneath the machined surface.Particle fracture and dilodegment greatly influences the quality of a machined surface.It was also found that although a 2D model can reflect certain material removal features,its ability to predict microstructural variation is limited.展开更多
By using the lattice model combined with finite element methods andstatistical techniques, a numerical approach is developed to establish mechanical models ofthree-dimensional heterogeneous brittle materials. A specia...By using the lattice model combined with finite element methods andstatistical techniques, a numerical approach is developed to establish mechanical models ofthree-dimensional heterogeneous brittle materials. A special numerical code is introduced, in whicha lattice model and statistical approaches are used to simulate the initial heterogeneity ofmaterial properties. The size of displacement-load step is adap-tively determined so that only fewelements would fail in each load step. When the tensile principal strain in an element exceeds theultimate strain of this element, the element is considered broken and its Young's modulus is set tobe very low. Some important behaviors of heterogeneous brittle materials are indicated using thiscode. Load-displacement curves and figures of three-dimensional fracture patterns are alsonumerically obtained, which are similar to those observed in laboratory tests.展开更多
Three-dimensional elasticity solutions for static bending of thick functionally graded plates are presented using a hybrid semi-analytical approach-the state-space based differential quadrature method （SSDQM）. The p...Three-dimensional elasticity solutions for static bending of thick functionally graded plates are presented using a hybrid semi-analytical approach-the state-space based differential quadrature method （SSDQM）. The plate is generally supported at four edges for which the two-way differential quadrature method is used to solve the in-plane variations of the stress and displacement fields numerically. An approximate laminate model （ALM） is exploited to reduce the inhomogeneous plate into a multi-layered laminate, thus applying the state space method to solve analytically in the thickness direction. Both the convergence properties of SSDQM and ALM are examined. The SSDQM is validated by comparing the numerical results with the exact solutions reported in the literature. As an example, the Mori-Tanaka model is used to predict the effective bulk and shear moduli. Effects of gradient index and aspect ratios on the bending behavior of functionally graded thick plates are investigated.展开更多
A series of three-dimensional ordered macroporous(3 DOM)W-TiO_(2)catalysts have been prepared through a facile colloidal crystal template method.The prepared materials characterized in detail exhibited enhanced cataly...A series of three-dimensional ordered macroporous(3 DOM)W-TiO_(2)catalysts have been prepared through a facile colloidal crystal template method.The prepared materials characterized in detail exhibited enhanced catalytic activity in aerobic oxidative desulfurization process.The experimental results indicated that the as-prepared materials possessed excellent 3 DOM structure,which is beneficial for the catalytic activity.The sample 3 DOM W-TiO_(2)-20 exhibited the highest activity in ODS process,and the sulfur removal can reach 98%in 6 h.Furthermore,the oxidative product was also analyzed in the reaction process.展开更多
The silica opal templates were prepared from three silica colloids of different diameters of 230 nm, 500 nm and 1.5 mm by a filtration route. The large-scale stable opal template membranes after sintering the deposite...The silica opal templates were prepared from three silica colloids of different diameters of 230 nm, 500 nm and 1.5 mm by a filtration route. The large-scale stable opal template membranes after sintering the deposited SiO2 opal template can be successfully obtained by optimizing the pH value and NaCl concentration in silica colloidal solutions. The three-dimensionally ordered macroporous（3DOM） polyimide membranes without crack were fabricated by reproducing the structure of silica opal template. We prepared the pore-filling composite proton exchange membranes by filling the 3DOM structure with proton conducting organosilane sol. The result indicates that the composite membranes exhibit higher water uptake than pure filling organosilane gel. The proton conductivity increased with the increasing of pore cell in composite membranes.展开更多
A new microelement method for the analyses of functionally graded structures was proposed. The key of this method is the maneuverable combination of two kinds of elements. Firstly, the macro elements are divided from ...A new microelement method for the analyses of functionally graded structures was proposed. The key of this method is the maneuverable combination of two kinds of elements. Firstly, the macro elements are divided from the functionally graded material structures by the normal finite elements. In order to reflect the functionally graded distributions of materials and the microconstitutions in each macro-element, the microelement method sets up the dense microelements in every macro-element, and translates nodes to the same as the normal finite elements by the degrees of freedom of all microelemental the compatibility conditions. This microelement method can fully reflect the micro constitutions and different components of materials, and its computational elements are the same as the normal finite elements, so it is an effective numerical method for the analyses of the functionally graded material structures. The three-dimensional analyses of functionally graded plates with medium components and different micro net structures are given by using the microelement method in this paper. The differences of the stress contour in the plane of functionally graded plates with different net microstructures are especially given in this paper.展开更多
Under hydrothermal and solvothermal conditions,two novel cobalt-based complexes,{[Co_(2)(CIA)(OH)(1,4-dtb)]·3.2H_(2)O}n(HU23)and{[Co_(2)(CIA)(OH)(1,4-dib)]·3.5H2O·DMF}n(HU24),were successfully construct...Under hydrothermal and solvothermal conditions,two novel cobalt-based complexes,{[Co_(2)(CIA)(OH)(1,4-dtb)]·3.2H_(2)O}n(HU23)and{[Co_(2)(CIA)(OH)(1,4-dib)]·3.5H2O·DMF}n(HU24),were successfully constructed by coordinatively assembling the semi-rigid multidentate ligand 5-(1-carboxyethoxy)isophthalic acid(H₃CIA)with the Nheterocyclic ligands 1,4-di(4H-1,2,4-triazol-4-yl)benzene(1,4-dtb)and 1,4-di(1H-imidazol-1-yl)benzene(1,4-dib),respectively,around Co^(2+)ions.Single-crystal X-ray diffraction analysis revealed that in both complexes HU23 and HU24,the CIA^(3-)anions adopt aκ^(7)-coordination mode,bridging six Co^(2+)ions via their five carboxylate oxygen atoms and one ether oxygen atom.This linkage forms tetranuclear[Co4(μ3-OH)2]^(6+)units.These Co-oxo cluster units were interconnected by CIA^(3-)anions to assemble into 2D kgd-type structures featuring a 3,6-connected topology.The 2D layers were further connected by 1,4-dtb and 1,4-dib,resulting in 3D pillar-layered frameworks for HU23 and HU24.Notably,despite the similar configurations of 1,4-dtb and 1,4-dib,differences in their coordination spatial orientations lead to topological divergence in the 3D frameworks of HU23 and HU24.Topological analysis indicates that the frameworks of HU23 and HU24 can be simplified into a 3,10-connected net(point symbol:(4^(10).6^(3).8^(2))(4^(3))_(2))and a 3,8-connected tfz-d net(point symbol:(4^(3))_(2)((4^(6).6^(18).8^(4)))),respectively.This structural differentiation confirms the precise regulatory role of ligands on the topology of metal-organic frameworks.Moreover,the ultraviolet-visible absorption spectra confirmed that HU23 and HU24 have strong absorption capabilities for ultraviolet and visible light.According to the Kubelka-Munk method,their bandwidths were 2.15 and 2.08 eV,respectively,which are consistent with those of typical semiconductor materials.Variable-temperature magnetic susceptibility measurements(2-300 K)revealed significant antiferromagnetic coupling in both complexes,with their effective magnetic moments decreasing markedly as the temperature lowered.CCDC:2457554,HU23;2457553,HU24.展开更多
基金financially supported by the National Key Research and Development Program of China(No.2020YFC1909604)the Natural Science Foundation of China(Nos.52202269 and 52002248)+1 种基金Shenzhen Science and Technology program(No.20220810155330003)Shenzhen Basic Research Program(No.JCYJ20190808163005631)。
文摘Reasonable design and applications of graphene-based materials are supposed to be promising ways to tackle many fundamental problems emerging in lithium batteries,including suppression of electrode/electrolyte side reactions,stabilization of electrode architecture,and improvement of conductive component.Therefore,extensive fundamental research on this aspect has been performed so far.However,when it comes to large-scale industrial applications,the utilization of graphene-based materials progresses at a very slow pace.Namely,there presents a severe technological decoupling between academic research and industrial application,and there is an urgent need to link them.Herein,in order to address current issues of graphene-based materials used in lithium batteries,we present their latest advancements with stateof-the-art technologies.Potential applications of graphenebased materials in practical lithium batteries are highlighted and predicted to bridge the gap between the academic progress and industrial manufacture,thereby paving the way for accelerating the development of graphenebased material as well as lithium battery industry.
基金supported by the National Natural Science Foundation of China(Nos.21674026,21574032,51573125,51573147,51803149,51973155,and 51633007(the State Key Program))the Sino-German Center for Research Promotion(No.GZ1286)the Chinese Academy of Sciences(No.121D11KYSB20170031).
文摘Two reported three-dimensional covalent organic frameworks(3D-COFs),COF-300 and COF-301,which have hierarchical porous structures and large pore volumes,were synthesized and employed as host materials for lithium-sulfur batteries.Owing to possessing excellent porosities as well as abundant hydroxyl groups in the pore walls,COF-301 can not only trap lithium polysulfides(PSs)via physical adsorption inside the pores,but also capture PSs by chemical interactions to relieve the shuttle effect.Interestingly,it is the first time that 3D-COFs were utilized as host materials for lithium-sulfur batteries as well as hydroxyl groups were introduced into COFs for improving the battery performance.As a result,COF-301@S as cathode material could reserve the capacity of 411.6 mA·h·g^-1 after 500 cycles with only 0.081%fading per cycle at 0.5 C,exhibiting better battery performance compared with COF-300@S.This study not only expands the applications of 3D-COFs but also provides a new route for designing lithium-sulfur batteries.
基金supported by the Reserve Talents Project of Yunnan Province(2013HB068)Applied Basic Research Program of Yunnan Province(2014FB127)
文摘The three-dimensional ordered macroporous CeO2：Yb,Er materials were prepared, and the influence of doping concentra- tion of Yb3＋ or Er3＋ ions on upconversion property was investigated. Green and red upconversion emissions were observed under the excitation of 980 nm at room temperature. It was found that the ratio of red to green upconversion emission intensity increased with increasing of concentration of the Yb3＋ or Er3＋ ions in the three-dimensional ordered macroporous CeO2：Yb,Er materials. When the concentration of Yb3＋ was 10 mol%, pure red upconversion emission was obtained. The varied mechanism of ratio of red to green upconversion emission intensity was discussed with the concentration of Yb3＋ or Er3＋ ions.
基金Scientific Research Fund of Institute of Engineering Mechanics,China Earthquake Administration under Grant No.2019B12National Natural Science Foundation of China Youth Fund under Grant No.51108433National Natural Science Foundation of China under Grant No.51778186。
文摘Damage indices are effective in quantifying structural seismic damage.Numerous response-based damage indices have been developed and validated through the hysteretic response of various experimental specimens.However,the accuracy of these indices for evaluating damage of RC columns is challenged by fluctuating axial load and irregular horizontal loading paths from 3-D earthquake excitations.This study introduces D_(iem),a material-based damage model for RC columns under random bidirectional loads and variable axial forces.Section damage indices of the plastic hinge are calculated by integrating the damage indices of concrete and steel fiber elements,considering their distance to the centroid axis.The P-Δeffect index is defined,and the component failure index is calculated using a combination of these indices.A hysteretic simulation and D_(iem)damage analysis program for cantilever RC columns is developed using Fortran.Three RC columns tested under bidirectional hysteretic loading are simulated to calibrate the program.Parameter analysis of 1,638 RC columns is conducted to verify D_(iem)’s applicability.The results demonstrated that D_(iem)’s failure assessment aligns with the 80%residual criterion.D_(iem)analysis of a real seismic damaged RC column shows satisfactory agreement with post-earthquake damage assessment and illustrates significant damage differences between columns with and without axial load fluctuation.
基金Funded by the National Natural Science Foundation of China(Nos.11102136 and 41362016)the Open Project of Guangxi Key Laboratory of Disaster Prevention and Structural Safety(No.2013ZDK09)
文摘An orthotropic functionally graded piezoelectric rectangular plate with arbitrarily distributed material properties was studied, which is simply supported and grounded（electrically） on its four lateral edges. The state equations of the functionally graded piezoelectric material were obtained using the state-space approach, and a Peano-Baker series solution was obtained for the coupled electroelastic fi elds of the functionally graded piezoelectric plate subjected to mechanical and electric loading on its upper and lower surfaces. The influence of different distributions of material properties on the structural response of the plate was studied using the obtained solutions.
基金supported by the National Natural Science Foundation of China(21325731,21221004 and 51478241)~~
文摘Three-dimensional（3D）ordered mesoporous MnO2 was prepared using KIT-6 mesoporous molecular sieves as a hard template.The material was used for catalytic oxidation of HCHO.The material has high surface areas and the mesoporous characteristics of the template,with cubic symmetry（ia3d）.It consists of a β-MnO2 crystalline phase corresponding to pyrolusite,with a rutile structure.Transmission electron microscopy and X-ray photoelectron spectroscopy showed that the 3D-MnO2 catalyst has a large number of exposed Mn4＋ ions on the（110）crystal plane surfaces,with a lattice spacing of 0.311 nm; this enhances oxidation of HCHO.Complete conversion of HCHO to CO2 and H2O was achieved at 130 °C on 3D-MnO2; the same conversions on α-MnO2 and β-MnO2 nanorods were obtained at 140 and 180 °C,respectively,under the same conditions.The specific mesoporous structure,high specific surface area,and large number of surface Mn4＋ ions are responsible for the catalytic activity of 3D-MnO2 in HCHO oxidation.
基金Project(2012QNZT003)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(2012M521542)supported by the Postdoctoral Science Foundation of China+1 种基金Project(14JJ3014)supported by the Hunan Provincial Natural Science Foundation of ChinaProject(BSh1202)supported by the Zhejiang Provincial Postdoctoral Scientific Research Foundation of China
文摘Arc erosion morphologies of Ag/MeO（10） electrical contact materials after 50000 operations under direct current of 19 V and 20 A and resistive load conditions were investigated using scanning electron microscope（SEM） and a 3D optical profiler（3DOP）. The results indicated that 3DOP could supply clearer and more detailed arc erosion morphology information. Arc erosion resistance of Ag/SnO_2（10） electrical contact material was the best and that of Ag/CuO（10） was the worst. Arc erosion morphology of Ag/MeO（10） electrical contact materials mainly included three different types. Arc erosion morphologies of Ag/ZnO（10） and Ag/SnO_2（10） electrical contact materials were mainly liquid splash and evaporation, and those of Ag/CuO（10） and Ag/CdO（10） were mainly material transfer from anode to cathode. Arc erosion morphology of Ag/SnO_2（6）In_2O_3（4） electrical contact materials included both liquid splash, evaporation and material transfer. In addition, the formation process and mechanism on arc erosion morphology of Ag/MeO（10） electrical contact materials were discussed.
基金supported by the National Natural Science Foundation of China(21673142)National Engineering Laboratory for Mobile Source Emission Control Technology(NELMS2017A05)+1 种基金PetroChina Innovation Foundation(2018D-5007-0505)Science Foundation of China University of Petroleum,Beijing(242017QNXZ02,2462018BJC005)~~
文摘Three-dimensional ordered macroporous (3DOM) La1?xKxNiO3 perovskite-type catalysts were successfully prepared by a colloidal crystal template method and characterized by scanning electron microscopy, transmission electron microscopy, high-resolution transmission electron microscopy, energy-dispersive X-ray scattering elemental mapping, X-ray diffraction, Raman and X-ray photoelectron spectroscopy, and temperature-programmed reduction of H2. Further, their catalytic activity in soot combustion was determined by temperature-programmed oxidation reaction. K substitution into the LaNiO3 lattice led to remarkably improved catalytic activity of this catalyst in soot combustion. Amongst various catalysts, La0.95K0.05NiO3 exhibited the highest activity in soot combustion (with its T50 and CO2 S values being 338 °C and 98.2%, respectively), which is comparable to the catalytic activities of Pt-based catalysts under the condition of poor contact between the soot and the catalyst. K-substitution improves the valence state of Ni and increases the number of oxygen vacancies, thereby leading to increased density of surface-active oxygen species. The active oxygen species play a vital role in catalyzing the elimination of soot. The perovskite-type La1?xKxNiO3 nanocatalysts with 3DOM structure without noble metals have potential for practical applications in the catalytic combustion of diesel soot particles.
基金financially supported by the Graduate Scientific Research and Innovation Foundation of Chongqing,China(No.CYS20001)。
文摘As a two-dimensional(2D)material,graphene shows excellent advantages in the field of gas sensors due to its inherent large specific surface area and unique electrical properties.However,in the practical application of gas detection,graphene sheet is easy to form irreversible agglomeration and has some limitations such as low sensitivity,long response time and slow recovery speed,which greatly reduce its gas sensing performance.As a gas sensing material,three-dimensional(3D)porous graphene has been extensively studied in recent years owing to its larger specific surface area and stable structure.In order to synthesize graphene with different three-dimensional structures,many methods have been developed.Herein,the synthesis and assembly of three-dimensional graphene and its composites were reviewed,with emphasis on the application of three-dimensional graphene and its composites in the field of gas sensors.The challenges and development prospects of three-dimensional graphene materials in the application of gas sensors were briefly described.
基金financially supported by the National Natural Science Foundation of China(No.51802195)Chen Guang Scholar Project of Shanghai Education Commission(No.19CG53)。
文摘Three-dimensional(3D)functional graphenebased architecture with superior electrical conductivity and good mechanical strength has promising applications in energy storage and electrics.Viscoelasticity-adjustable inks make it possible to achieve desired 3D architectures with interconnected and continuous interior networks by microextrusion printing.In this work,ultra-low-concentration graphene oxide(GO)inks of~15 mg·ml-1 have been obtained and demonstrated in direct 3D printing with a facile cross-linking(direct ink writing).The rheological behavior of the GO strategy by cations,which is the lowest concentration to achieve direct ink writing inks,could be adjusted from 1×10^(4) to 1×10^(5) Pa·s^(-1) with different concentrations of cations due to strong cross-linking networks between GO sheets and cations.Meanwhile,the specific strength and electrical conductivity of 3D-printed graphene architecture are notably enhanced,reaching up to 51.7×10^(3) N·m·kg^(-1)and 119 S·m^(-1),which are superior to conventional graphene aerogels.Furthermore,3D printing graphene-based architecture assembled in micro-superc apacitor exhibits excellent electrochemical performance,which can be ascribed to the effective ion transportation through the interconnected networks.The strategy demonstrated is useful in the design of complex-shaped,graphene-based architectures for scalable manufacturing of practical energy storage applications.
基金Project supported by the National Natural Sciences Foundation of China(No.10432030).
文摘A three-dimensional analysis of a simply-supported functionally graded rectangular plate with an arbitrary distribution of material properties is made using a simple and effective method based on the Haar wavelet. With good features in treating singularities, Haar series solution converges rapidly for arbitrary distributions, especially for the case where the material properties change rapidly in some regions. Through numerical examples the influences of the ratio of material constants on the top and bottom surfaces and different material gradient distributions on the structural response of the plate to mechanical stimuli are studied.
文摘The use of three-dimensional(3D)electrodes in water treatment is competitive because of their high catalytic efficiency,low energy consumption and promising development.The use of particle electrodes is a key research focus in this technology.They are usually in the form of particles that fill the space between the cathode and anode,and the selection of materials used is important.Carbon-based materials are widely used because of their large specific surface area,good adsorption performance,high chemical stability and low cost.The principles of 3D electrode technology are introduced and recent research on its use for degrading organic pollutants using carbon-based particle electrodes is summarized.The classification of particle electrodes is introduced and the challenges for the future development of carbon-based particle electrodes in wastewater treatment are discussed.
文摘Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal mechanisms(MRMs)involved in the machining of PRMMCs.This paper develops a three-dimensional(3D)microstructure-based model for investigating the MRM and surface integrity of machined PRMMCs.To accurately mimic the actual microstructure of a PRMMC,polyhedrons were randomly distributed inside the matrix to represent irregular SiC particles.Particle fracture and matrix deformation and failure were taken into account.For the model’s capability comparison,a two-dimensional(2D)analysis was also conducted.Relevant cutting experiments showed that the established 3D model accurately predicted the material removal,chip morphology,machined surface finish,and cutting forces.It was found that the matrix-particle-tool interactions led to particle fractures,mainly in the primary shear and secondary deformation zones along the cutting path and beneath the machined surface.Particle fracture and dilodegment greatly influences the quality of a machined surface.It was also found that although a 2D model can reflect certain material removal features,its ability to predict microstructural variation is limited.
文摘By using the lattice model combined with finite element methods andstatistical techniques, a numerical approach is developed to establish mechanical models ofthree-dimensional heterogeneous brittle materials. A special numerical code is introduced, in whicha lattice model and statistical approaches are used to simulate the initial heterogeneity ofmaterial properties. The size of displacement-load step is adap-tively determined so that only fewelements would fail in each load step. When the tensile principal strain in an element exceeds theultimate strain of this element, the element is considered broken and its Young's modulus is set tobe very low. Some important behaviors of heterogeneous brittle materials are indicated using thiscode. Load-displacement curves and figures of three-dimensional fracture patterns are alsonumerically obtained, which are similar to those observed in laboratory tests.
基金Project supported by the National Natural Science Foundation of China(Nos.51108412,11472244,and 11202186)the National Basic Research Program of China(973 Program)(No.2013CB035901)+1 种基金the Fundamental Research Funds for the Central Universities(No.2014QNA4017)the Zhejiang Provincial Natural Science Foundation of China(No.LR13A020001)
文摘Three-dimensional elasticity solutions for static bending of thick functionally graded plates are presented using a hybrid semi-analytical approach-the state-space based differential quadrature method （SSDQM）. The plate is generally supported at four edges for which the two-way differential quadrature method is used to solve the in-plane variations of the stress and displacement fields numerically. An approximate laminate model （ALM） is exploited to reduce the inhomogeneous plate into a multi-layered laminate, thus applying the state space method to solve analytically in the thickness direction. Both the convergence properties of SSDQM and ALM are examined. The SSDQM is validated by comparing the numerical results with the exact solutions reported in the literature. As an example, the Mori-Tanaka model is used to predict the effective bulk and shear moduli. Effects of gradient index and aspect ratios on the bending behavior of functionally graded thick plates are investigated.
基金the financial support from the National Natural Science Foundation of China(Nos.21722604 and 21776116)China Postdoctoral Science Foundation(2020M671365)+2 种基金Jiangsu Postdoctoral Research Funding Program(No.2021K343C)Natural Science Foundation of Jiangsu Province(No.BK20190243)the Society Development Fund of Zhenjiang City(SH2020020)。
文摘A series of three-dimensional ordered macroporous(3 DOM)W-TiO_(2)catalysts have been prepared through a facile colloidal crystal template method.The prepared materials characterized in detail exhibited enhanced catalytic activity in aerobic oxidative desulfurization process.The experimental results indicated that the as-prepared materials possessed excellent 3 DOM structure,which is beneficial for the catalytic activity.The sample 3 DOM W-TiO_(2)-20 exhibited the highest activity in ODS process,and the sulfur removal can reach 98%in 6 h.Furthermore,the oxidative product was also analyzed in the reaction process.
基金Supported by the National Natural Science Foundation of China(Nos.20704004, 21074019)the Natural Science Foundation of Jilin Province, China(No.20101539)
文摘The silica opal templates were prepared from three silica colloids of different diameters of 230 nm, 500 nm and 1.5 mm by a filtration route. The large-scale stable opal template membranes after sintering the deposited SiO2 opal template can be successfully obtained by optimizing the pH value and NaCl concentration in silica colloidal solutions. The three-dimensionally ordered macroporous（3DOM） polyimide membranes without crack were fabricated by reproducing the structure of silica opal template. We prepared the pore-filling composite proton exchange membranes by filling the 3DOM structure with proton conducting organosilane sol. The result indicates that the composite membranes exhibit higher water uptake than pure filling organosilane gel. The proton conductivity increased with the increasing of pore cell in composite membranes.
基金supported by the National Natural Science Foundation of China (No.10432030)the National Youth Science Foundation of China (No.10802091)the Scientific and Technical Foundation of China University of Mining and Technology (No.2007B013)
文摘A new microelement method for the analyses of functionally graded structures was proposed. The key of this method is the maneuverable combination of two kinds of elements. Firstly, the macro elements are divided from the functionally graded material structures by the normal finite elements. In order to reflect the functionally graded distributions of materials and the microconstitutions in each macro-element, the microelement method sets up the dense microelements in every macro-element, and translates nodes to the same as the normal finite elements by the degrees of freedom of all microelemental the compatibility conditions. This microelement method can fully reflect the micro constitutions and different components of materials, and its computational elements are the same as the normal finite elements, so it is an effective numerical method for the analyses of the functionally graded material structures. The three-dimensional analyses of functionally graded plates with medium components and different micro net structures are given by using the microelement method in this paper. The differences of the stress contour in the plane of functionally graded plates with different net microstructures are especially given in this paper.
文摘Under hydrothermal and solvothermal conditions,two novel cobalt-based complexes,{[Co_(2)(CIA)(OH)(1,4-dtb)]·3.2H_(2)O}n(HU23)and{[Co_(2)(CIA)(OH)(1,4-dib)]·3.5H2O·DMF}n(HU24),were successfully constructed by coordinatively assembling the semi-rigid multidentate ligand 5-(1-carboxyethoxy)isophthalic acid(H₃CIA)with the Nheterocyclic ligands 1,4-di(4H-1,2,4-triazol-4-yl)benzene(1,4-dtb)and 1,4-di(1H-imidazol-1-yl)benzene(1,4-dib),respectively,around Co^(2+)ions.Single-crystal X-ray diffraction analysis revealed that in both complexes HU23 and HU24,the CIA^(3-)anions adopt aκ^(7)-coordination mode,bridging six Co^(2+)ions via their five carboxylate oxygen atoms and one ether oxygen atom.This linkage forms tetranuclear[Co4(μ3-OH)2]^(6+)units.These Co-oxo cluster units were interconnected by CIA^(3-)anions to assemble into 2D kgd-type structures featuring a 3,6-connected topology.The 2D layers were further connected by 1,4-dtb and 1,4-dib,resulting in 3D pillar-layered frameworks for HU23 and HU24.Notably,despite the similar configurations of 1,4-dtb and 1,4-dib,differences in their coordination spatial orientations lead to topological divergence in the 3D frameworks of HU23 and HU24.Topological analysis indicates that the frameworks of HU23 and HU24 can be simplified into a 3,10-connected net(point symbol:(4^(10).6^(3).8^(2))(4^(3))_(2))and a 3,8-connected tfz-d net(point symbol:(4^(3))_(2)((4^(6).6^(18).8^(4)))),respectively.This structural differentiation confirms the precise regulatory role of ligands on the topology of metal-organic frameworks.Moreover,the ultraviolet-visible absorption spectra confirmed that HU23 and HU24 have strong absorption capabilities for ultraviolet and visible light.According to the Kubelka-Munk method,their bandwidths were 2.15 and 2.08 eV,respectively,which are consistent with those of typical semiconductor materials.Variable-temperature magnetic susceptibility measurements(2-300 K)revealed significant antiferromagnetic coupling in both complexes,with their effective magnetic moments decreasing markedly as the temperature lowered.CCDC:2457554,HU23;2457553,HU24.
