According to the Mindlin plate theory and the first-order piston theory,this work obtains accurate closed-form eigensolutions for the flutter problem of three-dimensional(3D)rectangular laminated panels.The governing ...According to the Mindlin plate theory and the first-order piston theory,this work obtains accurate closed-form eigensolutions for the flutter problem of three-dimensional(3D)rectangular laminated panels.The governing differential equations are derived by the Hamilton's variational principle,and then solved by the iterative Separation-of-Variable(i SOV)method,which are applicable to arbitrary combinations of homogeneous Boundary Conditions(BCs).However,only the simply-support,clamped and cantilever panels are considered in this work for the sake of clarity.With the closed-form eigensolutions,the flutter frequency,flutter mode and flutter boundary are presented,and the effect of shear deformation and aerodynamic damping on flutter frequencies is investigated.Besides,the relation between panel energy and the work of aerodynamic load is discussed.The numerical comparisons reveal the following.(A)The flutter eigenvalues obtained by the present method are accurate,validated by the Finite Element Method(FEM)and the Galerkin method.(B)When the span-chord ratio is larger than 3,simplifying a 3D panel to 2D(two-dimensional)panel is reasonable and the relative differences of the flutter points predicted by the two models are less than one percent.(C)The reciprocal relationship between the mechanical energy of the panel and the work done by aerodynamic load is verified by using the present flutter eigenvalues and modes,further indicating the high accuracy of the present solutions.(D)The coupling of shear deformation and aerodynamic damping prevents frequency coalescing.展开更多
A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on...A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on the three-dimensional morphology of TiB2 particles.Different preparation routes result in different reaction forms,which accounts for the morphology variation of TiB2 particles.When the Al-Ti-B master alloy is prepared using ＂halide salt＂ route,TiB2 particles exhibit hexagonal platelet morphology and are independent with each other.In addition,the reaction temperature almost does not have influence on the morphology of TiB2 particles.However,TiB2 particles exhibit different morphologies at different reaction temperatures when the master alloys are prepared with Al-3B and Ti sponge.When the master alloy is prepared at 850 ℃,a kind of TiB2 particle agglomeration forms with a size larger than 5 μm.The TiB2 particles change to layered stacking morphology even dendritic morphology with the reaction temperature reaching up to 1200 ℃.展开更多
Taking half-tube part with curvature as an example,the Impact Hydroforming(IHF)characteristics were studied by combining the actual forming experiment and numerical simulation.The IHF experiment showed that wrinkles a...Taking half-tube part with curvature as an example,the Impact Hydroforming(IHF)characteristics were studied by combining the actual forming experiment and numerical simulation.The IHF experiment showed that wrinkles appeared at the bottom of the part during single-step forming,but no wrinkles were observed during double-step forming.The thinning rate and deviation of the wall thickness of the part in each area were less than 20%and 2.7 mm,correspondingly,and the drawing depth of the part reached 45.8 mm.The effect of double-step forming was better than that of single-step forming,which was related to the IHF forming law.Besides,the characteristics of the IHF process were studied by numerical simulation.The results indicated that when double-step forming was utilized,there was almost no velocity field in the opposite direction of deformation after the bottom of the part contacted the die,and the existence of stress state at the bottom would restrain and eliminate the wrinkles.The inertia effect evolved with the driving pressure.Specially,the inertia effect can improve the flow of metal and reduce the deviation of the wall thickness of the part under double-step forming.展开更多
The multi-pass intermittent local loading process,which features a more flexible processing path,can further enhance the second material distribution during local loading,improve the formability of components,and redu...The multi-pass intermittent local loading process,which features a more flexible processing path,can further enhance the second material distribution during local loading,improve the formability of components,and reduce forming loads.However,the absence of compatible forming equipment makes it difficult to control the constraint in the unloaded zones during the forming process.This difficulty complicates coordination and control of deformation,particularly for asymmetric rib-web components.Additionally,the current implementation involves multi-fire heating,a long process flow,and high energy consumption,which limits the popularization and application of the local loading process.In this study,a new multi-pass local loading hydraulic forming apparatus that can quickly and reliably switch between heavy-load deformation and low-load constraint for different local loading sub-dies was developed.A 10-tonne laboratory prototype was developed,and the forming characteristics during the forming process as well as the response characteristics of the hydraulic system during the multi-pass intermittent local loading of rib-web component were investigated using numerical simulations and physical experiments.Results indicated that,compared to a whole loading process with the same initial geometry of billet,the total forming load(i.e.,the sum of loaded and restrained loads)is reduced by more than 40%with the local loading process,and by nearly 50%with multi-pass local loading.The multi-pass local loading process allows for more effective control of material flow compared to single-pass local loading,leading to improved cavity filling and reduced flow line disturbance.For a large-scale,complex titanium alloy bulkhead,the cavity filling problem was addressed by optimizing the multi-pass local loading path with an unequal thickness billet.The dynamic performance of the multi-pass local loading hydraulic system was found to be robust,with stable pressure transitions during motion and load switching for the sub-die(s).The dynamic characteristic of the hydraulic cylinder when switching from non-moving/unloaded state to a moving/loading state are consistent whether a load is present or not.However,the dynamic characteristics differ when switching from a moving/loading state to non-moving/unloaded state,showing opposite behavior.The developed hydraulic drive mechanism provides a way for implementation of multi-pass local loading without auxiliary operation and extra heating.The results of the study provide a foundation for the industrial production of large-scale,complex components with reduced force requirement and low-energy consumption.展开更多
In aerospace,nuclear power,and new energy vehicles industries,utilizing integrated metal components with extreme sizes and/or structures is crucial for achieving significant weight-saving,performance-improvement,and e...In aerospace,nuclear power,and new energy vehicles industries,utilizing integrated metal components with extreme sizes and/or structures is crucial for achieving significant weight-saving,performance-improvement,and excellent reliability.These components,made from metal sheets,rings,or tubes,exhibit characteristics like ultra-thin,ultra-thick,ultra-large,ultra-long,ultra-high ribs,and large variable diameters.During plastic de-formation in metal forming processes,defects such as ruptures,wrinkles,excessive strain differences,and un-expected weak performance areas are likely to occur due to the intersection of multiple effects in different research disciplines,including materials science,processes,and mechanics of materials.Consequently,the smooth forming of integrated parts is difficult.It is the first time to review,summarize,and analyze the ad-vancement of forming methods for producing integrated parts with extreme sizes and structures.The general academic ideas to change the process conditions and sequences to optimize stress state and improve plastic deformation ability for forming the components with extreme sizes/structures are introduced.Practical ex-amples,discussed in detail in the paper,include the forming of(i)integrated ultra-thin and ultra-thick sheet components;(ii)integrated ultra-large size ring components with thin wall and high ribs;and(iii)integrated ultra-long tube components with large perimeter difference.Various plasticity technologies and process se-quences have been developed.The key processes and applications of the technologies are discussed in detail,which achieve successful plastic forming of integrated components.This paper provides state-of-the-art and perspectives for the rapidly advancing material forming fields of key metal components for the next generation of equipment.展开更多
Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic...Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic FEM code has been developed. Isothermal forging process of a cylindrical housing has been simulated. The simulation results show that the given techniques and the FEM code are reasonable and feasible for three-dimensional bulk forming processes.展开更多
The dispersibility of active components in hydrodesulfurization(HDS)catalysts significantly influences the corresponding catalytic performance.In this study,sugar-based materials(glucose,chitosan,soluble starch,and co...The dispersibility of active components in hydrodesulfurization(HDS)catalysts significantly influences the corresponding catalytic performance.In this study,sugar-based materials(glucose,chitosan,soluble starch,and corn starch)were utilized to prepare CoMo bulk HDS catalysts through a sugar foaming process.The foaming intermediates were analyzed using TG,FTIR,and Raman techniques to investigate the pyrolysis and carbonization process,revealing the presence of graphitic carbon in the 3 DPG,3 DPSS,and 3 DPCS catalysts even after calcination in an air atmosphere.The catalysts were further characterized using SEM,XRD,TEM,low-temperature N_(2) physical adsorption,and XPS.The 3 DPSS catalyst exhibited a thiophene conversion of 94.8%at 360℃ and 1 MPa,which could be ascribed to its unique three-dimensional pore structure,high dispersion of MoS_(2)(0.21),and high fraction of Mo^(4+)(83.14%).This study demonstrates the potential of using the sugar foaming technique to develop highly efficient HDS catalysts and provides new insights into the relationship between the physicochemical properties of the obtained catalysts and their catalytic performance.展开更多
To address the poor mechanical properties of polydimethylsiloxane(PDMS)and enhance the understanding of the reinforcement mechanisms of aerogel network structures in rubber matrices,this study reinforced PDMS using an...To address the poor mechanical properties of polydimethylsiloxane(PDMS)and enhance the understanding of the reinforcement mechanisms of aerogel network structures in rubber matrices,this study reinforced PDMS using an ordered interconnected three-dimensional montmorillonite(MMT)aerogel network.The average pore diameter of the aerogels was successfully reduced from 11.53μm to 2.51μm by adjusting the ratio of poly(vinyl alcohol)(PVA)to MMT via directional freezing.Changes in the aerogel network were observed in field emission scanning electron microscope(FESEM)images.After vacuum impregnation,the aerogel network structure of the composites was observed using FESEM.Tensile tests indicated that as the pore diameter decreased,the elongation at break of the composites first increased to a peak of329.61%before decreasing,while the tensile strength and Young's modulus continuously increased to their maximum values of 6.29 MPa and24.67 MPa,respectively.Meanwhile,FESEM images of the tensile cracks and fracture surfaces showed that with a reduction in aerogel pore diameter,the degrees of crack deflection and interfacial debonding increased,presenting a rougher fracture surface.These phenomena enable the composites to dissipate substantial energy during tension,thus effectively improving the mechanical strength of the composites.The present work elucidates the bearing of ordered three-dimensional aerogel network structures on the performance of rubber matrices and provides crucial theoretical insights and technical guidance for the creation and optimization of high-performance PDMS-based composites.展开更多
Intercepting high-maneuverability hypersonic targets in near-space environments poses significant challenges due to their extreme speeds and evasive capabilities.To address these challenges,this study presents an inte...Intercepting high-maneuverability hypersonic targets in near-space environments poses significant challenges due to their extreme speeds and evasive capabilities.To address these challenges,this study presents an integrated approach that combines a Three-Dimensional Finite-Time Optimal Cooperative Guidance Law(FTOC)with an Information Fusion Anti-saturation Predefined-time Observer(IFAPO).The proposed FTOC guidance law employs a nonlinear,non-quadratic finite-time optimal control strategy designed for rapid convergence within the limited timeframes of near-space interceptions,avoiding the need for remaining flight time estimation or linear decoupling inherent in traditional methods.To complement the guidance strategy,the IFAPO leverages multi-source information fusion theory and incorporates anti-saturation mechanisms to enhance target maneuver estimation.This method ensures accurate and real-time prediction of target acceleration while maintaining predefined convergence performance,even under complex interception conditions.By integrating the FTOC guidance law and IFAPO,the approach optimizes cooperative missile positioning,improves interception success rates,and minimizes fuel consumption,addressing practical constraints in military applications.Simulation results and comparative analyses confirm the effectiveness of the integrated approach,demonstrating its capability to achieve cooperative interception of highly maneuvering targets with enhanced efficiency and reduced economic costs,aligning with realistic combat scenarios.展开更多
The internal hotspot temperature rise prediction in nanocrystalline high-frequency transformers(nanoHFTs) is essential to ensure reliable operation. This paper presents a three-dimensional thermal network(3DTN) model ...The internal hotspot temperature rise prediction in nanocrystalline high-frequency transformers(nanoHFTs) is essential to ensure reliable operation. This paper presents a three-dimensional thermal network(3DTN) model for epoxy resin encapsulated nano HFTs, which aims to precisely predict the temperature distribution inside the transformer in combination with the finite element method(FEM). A magnetothermal bidirectional coupling 3DTN model is established by analyzing the thermal conduction between the core, windings, and epoxy resin, while also considering the convection and radiation heat transfer mechanisms on the surface of the epoxy resin. The model considers the impact of loss distribution in the core and windings on the temperature field and adopts a simplified 1/2 thermal network model to reduce computational complexity. Furthermore, the results of FEM are compared with experimental results to verify the accuracy of the 3DTN model in predicting the temperature rise of nano HFT. The results show that the 3DTN model reduces errors by an average of 5.25% over the traditional two-dimensional thermal network(2DTN) model, particularly for temperature distributions in the windings and core. This paper provides a temperature rise prediction method for the thermal design and offers a theoretical basis and engineering guidance for the optimization of their thermal management systems.展开更多
The rational design of efficient and stable carbon-based electrocatalysts for oxygen reduction and oxygen evolution reactions is crucial for improving energy density and long-term stability of rechargeable zinc-air ba...The rational design of efficient and stable carbon-based electrocatalysts for oxygen reduction and oxygen evolution reactions is crucial for improving energy density and long-term stability of rechargeable zinc-air batteries(ZABs).Herein,a general and controllable synthesis method was developed to prepare three-dimensional(3D)porous carbon composites embedded with diverse metal phosphide nanocrystallites by interfacial coordination of transition metal ions with phytic acid-doped polyaniline networks and subsequent pyrolysis.Phytic acid as the dopant of polyaniline provides favorable anchoring sites for metal ions owing to the coordination interaction.Specifically,adjusting the concentration of adsorbed cobalt ions can achieve the phase regulation of transition metal phosphides.Thus,with abundant cobalt phosphide nanoparticles and nitrogen-and phosphorus-doping sites,the obtained carbon-based electrocatalysts exhibited efficient electrocatalytic activities toward oxygen reduction and evolution reactions.Consequently,the fabricated ZABs exhibited a high energy density,high power density of 368 mW cm^(-2),and good cycling/mechanical stability,which could power water splitting for integrated device fabrication with high gas yields.展开更多
To improve heat-transfer performance, a novel integral three-dimensional fin-structure on the plat surface was presented to increase the evaporation efficiency. The three-dimensional fin-structure is composed of a spi...To improve heat-transfer performance, a novel integral three-dimensional fin-structure on the plat surface was presented to increase the evaporation efficiency. The three-dimensional fin-structure is composed of a spiral micro-groove and multi radial micro-grooves. Both ploughing-extrusion(P-E) and stamping were used to form the integral-fins with a connection between radial and circumferential directions. Based on the SEM results, the relationships among P-E speed v P-E, rotational speed np and feed fp, and among interference length Li, stamping feed angle θc and stamping depth ac were analyzed. The effects of processing parameters on the groove morphology and the matching relationship between parameters were also discussed. The integral finned surface with micro-grooves and cracks can be obtained under such processing conditions: P-E depth ap=0.3 mm, ac=0.3 mm, the interval of helical groove dp=1.24 mm, θc=2° and np=50 r/min.展开更多
Three-dimensional（3D）ordered mesoporous MnO2 was prepared using KIT-6 mesoporous molecular sieves as a hard template.The material was used for catalytic oxidation of HCHO.The material has high surface areas and the ...Three-dimensional（3D）ordered mesoporous MnO2 was prepared using KIT-6 mesoporous molecular sieves as a hard template.The material was used for catalytic oxidation of HCHO.The material has high surface areas and the mesoporous characteristics of the template,with cubic symmetry（ia3d）.It consists of a β-MnO2 crystalline phase corresponding to pyrolusite,with a rutile structure.Transmission electron microscopy and X-ray photoelectron spectroscopy showed that the 3D-MnO2 catalyst has a large number of exposed Mn4＋ ions on the（110）crystal plane surfaces,with a lattice spacing of 0.311 nm; this enhances oxidation of HCHO.Complete conversion of HCHO to CO2 and H2O was achieved at 130 °C on 3D-MnO2; the same conversions on α-MnO2 and β-MnO2 nanorods were obtained at 140 and 180 °C,respectively,under the same conditions.The specific mesoporous structure,high specific surface area,and large number of surface Mn4＋ ions are responsible for the catalytic activity of 3D-MnO2 in HCHO oxidation.展开更多
A series of K-doped Mn0.5Ce0.5Oδ （K-MCO） catalysts with three-dimensionally ordered macroporous （3DOM） structure and different K loadings were successfully synthesized using simple methods. These catalysts exhibi...A series of K-doped Mn0.5Ce0.5Oδ （K-MCO） catalysts with three-dimensionally ordered macroporous （3DOM） structure and different K loadings were successfully synthesized using simple methods. These catalysts exhibited well-defined 3DOM nanostructure, which consisted of extensive interconnecting networks of spherical voids. The effects of the calcination temperature and calcination time on the morphological characteristics and crystalline forms of the catalysts were systematically studied. The catalysts showed high catalytic activity for the combustion of soot. 3DOM 20% K-MCO-4h catalyst, in particular, showed the highest catalytic activity of all of the catalysts studied （e.g., Ts0 = 331 ~C and Smco2 = 95.3%）. The occurrence of structural and synergistic effects among the K, Mn, and Ce atoms in the catalysts was favorable for enhancing their catalytic activity towards the combustion of diesel soot. Furthermore, the temperatures required for the complete combustion of the soot （〈400 ℃） were well within the exhaust temperature range （175-400 ℃）, which means that the accumulated soot can be removed under the conditions of the diesel exhaust gas. These catalysts could therefore be used in numerous practical applications because they are easy to synthesize, exhibit high catalytic activity, and can be made from low cost materials.展开更多
An integration processing system of three-dimensional laser scanning information visualization in goaf was developed. It is provided with multiple functions, such as laser scanning information management for goaf, clo...An integration processing system of three-dimensional laser scanning information visualization in goaf was developed. It is provided with multiple functions, such as laser scanning information management for goaf, cloud data de-noising optimization, construction, display and operation of three-dimensional model, model editing, profile generation, calculation of goaf volume and roof area, Boolean calculation among models and interaction with the third party soft ware. Concerning this system with a concise interface, plentiful data input/output interfaces, it is featured with high integration, simple and convenient operations of applications. According to practice, in addition to being well-adapted, this system is favorably reliable and stable.展开更多
Three-dimensional(3D)culture systems are becoming increasingly popular due to their ability to mimic tissue-like structures more effectively than the monolayer cultures.In cancer and stem cell research,the natural cel...Three-dimensional(3D)culture systems are becoming increasingly popular due to their ability to mimic tissue-like structures more effectively than the monolayer cultures.In cancer and stem cell research,the natural cell characteristics and architectures are closely mimicked by the 3D cell models.Thus,the 3D cell cultures are promising and suitable systems for various proposes,ranging from disease modeling to drug target identification as well as potential therapeutic substances that may transform our lives.This review provides a comprehensive compendium of recent advancements in culturing cells,in particular cancer and stem cells,using 3D culture techniques.The major approaches highlighted here include cell spheroids,hydrogel embedding,bioreactors,scaffolds,and bioprinting.In addition,the progress of employing 3D cell culture systems as a platform for cancer and stem cell research was addressed,and the prominent studies of 3D cell culture systems were discussed.展开更多
Using self-researched gas drainage borehole stability dynamic monitoring device, three-dimensional deformation characteristics of borehole under steady vertical load were researched experimentally and systematically. ...Using self-researched gas drainage borehole stability dynamic monitoring device, three-dimensional deformation characteristics of borehole under steady vertical load were researched experimentally and systematically. This research indicated that under the action of steady loading, the mechanical deformation path of the simulated gas drainage borehole is gradually complicated, and the decay of the borehole circumferential strain is an important characterization of the prediction and early warning of borehole instability and collapse. The horizontal position of borehole occurs compressive strain, and the vertical of which occurs tensile strain under the action of vertical stress. At the initial stage of loading, the vertical strain is more sensitive than that in the horizontal direction. After a certain period of time, the horizontal strain is gradually higher than the vertical one, and the intersection of the borehole horizontal diameter and the hole wall is the stress concentration point. With the increase of the depth of hole, the strain shows a gradual decay trend as a whole, and the vertical strain decays more observably, but there is no absolute position correlation between the amount of strain decay and the increase in borehole depth,and the area within 1.5 times the orifice size is the borehole stress concentration zone.展开更多
To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D lea...To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D leader-following cooperative interception guidance law.First,in the LOS direction of the leader,an impact time-controlled guidance law is derived based on the fixed-time stability theory,which enables the leader to complete the interception task at a prespecified impact time.Next,in the LOS direction of the followers,by introducing a time consensus tracking error function,a fixed-time consensus tracking guidance law is investigated to guarantee the consensus tracking convergence of the time-to-go.Then,in the direction normal to the LOS,by combining the designed global integral sliding mode surface and the second-order Sliding Mode Control(SMC)theory,an innovative 3D LOS-angle-constrained interception guidance law is developed,which eliminates the reaching phase in the traditional sliding mode guidance laws and effectively saves energy consumption.Moreover,it effectively suppresses the chattering phenomenon while avoiding the singularity issue,and compensates for unknown interference caused by target maneuvering online,making it convenient for practical engineering applications.Finally,theoretical proof analysis and multiple sets of numerical simulation results verify the effectiveness,superiority,and robustness of the investigated guidance law.展开更多
This study assessed the clinical application of transvaginal three-dimensional ultrasound （3D TVUS） in the diagnosis of congenital uterine malformation. A retrospective study was performed on 62 patients with congen...This study assessed the clinical application of transvaginal three-dimensional ultrasound （3D TVUS） in the diagnosis of congenital uterine malformation. A retrospective study was performed on 62 patients with congenital uterine malformation confirmed hysteroscopically and/or laparoscopically. The patients were subjected to transvaginal two-dimensional ultrasound （2D TVUS） and 3D TVUS. The accuracy rate was compared between the two methods. The accuracy rate of 3D TVUS was （98.38%, 61/62）, higher than that of 2D TVUS （80.65%, 50/62）. 3D TVUS coronal plane imaging could demon- strate the internal shape of the endometrial cavity and the external contour of the uterine fundus. It al- lowed accurate measurement on the coronary plane, and could three-dimensionally show the image of cervical tube, thereby providing information for the diagnosis of some complex uterine malformation. 3D TVUS imaging can obtain comprehensive information of the uterus malformation, and it is superior to 2D TVUS for the diagnosis of congenital uterine malformations, especially complex uterine anomaly.展开更多
The environment of low-altitude urban airspace is complex and variable due to numerous obstacles,non-cooperative aircraft,and birds.Unmanned Aerial Vehicles(UAVs)leveraging environmental information to achieve three-d...The environment of low-altitude urban airspace is complex and variable due to numerous obstacles,non-cooperative aircraft,and birds.Unmanned Aerial Vehicles(UAVs)leveraging environmental information to achieve three-dimension collision-free trajectory planning is the prerequisite to ensure airspace security.However,the timely information of surrounding situation is difficult to acquire by UAVs,which further brings security risks.As a mature technology leveraged in traditional civil aviation,the Automatic Dependent Surveillance-Broadcast(ADS-B)realizes continuous surveillance of the information of aircraft.Consequently,we leverage ADS-B for surveillance and information broadcasting,and divide the aerial airspace into multiple sub-airspaces to improve flight safety in UAV trajectory planning.In detail,we propose the secure Sub-airSpaces Planning(SSP)algorithm and Particle Swarm Optimization Rapidly-exploring Random Trees(PSO-RRT)algorithm for the UAV trajectory planning in law-altitude airspace.The performance of the proposed algorithm is verified by simulations and the results show that SSP reduces both the maximum number of UAVs in the sub-airspace and the length of the trajectory,and PSO-RRT reduces the cost of UAV trajectory in the sub-airspace.展开更多
基金support of the National Natural Science Foundation of China(No.12172023)。
文摘According to the Mindlin plate theory and the first-order piston theory,this work obtains accurate closed-form eigensolutions for the flutter problem of three-dimensional(3D)rectangular laminated panels.The governing differential equations are derived by the Hamilton's variational principle,and then solved by the iterative Separation-of-Variable(i SOV)method,which are applicable to arbitrary combinations of homogeneous Boundary Conditions(BCs).However,only the simply-support,clamped and cantilever panels are considered in this work for the sake of clarity.With the closed-form eigensolutions,the flutter frequency,flutter mode and flutter boundary are presented,and the effect of shear deformation and aerodynamic damping on flutter frequencies is investigated.Besides,the relation between panel energy and the work of aerodynamic load is discussed.The numerical comparisons reveal the following.(A)The flutter eigenvalues obtained by the present method are accurate,validated by the Finite Element Method(FEM)and the Galerkin method.(B)When the span-chord ratio is larger than 3,simplifying a 3D panel to 2D(two-dimensional)panel is reasonable and the relative differences of the flutter points predicted by the two models are less than one percent.(C)The reciprocal relationship between the mechanical energy of the panel and the work done by aerodynamic load is verified by using the present flutter eigenvalues and modes,further indicating the high accuracy of the present solutions.(D)The coupling of shear deformation and aerodynamic damping prevents frequency coalescing.
基金Project(50625101) supported by the National Science Fund for Distinguished Young Scholars of ChinaProject supported by Graduate Independent Innovation Foundation of Shandong University(GIIFSDU),ChinaProject(51071097) supported by the National Natural Science Foundation of China
文摘A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on the three-dimensional morphology of TiB2 particles.Different preparation routes result in different reaction forms,which accounts for the morphology variation of TiB2 particles.When the Al-Ti-B master alloy is prepared using ＂halide salt＂ route,TiB2 particles exhibit hexagonal platelet morphology and are independent with each other.In addition,the reaction temperature almost does not have influence on the morphology of TiB2 particles.However,TiB2 particles exhibit different morphologies at different reaction temperatures when the master alloys are prepared with Al-3B and Ti sponge.When the master alloy is prepared at 850 ℃,a kind of TiB2 particle agglomeration forms with a size larger than 5 μm.The TiB2 particles change to layered stacking morphology even dendritic morphology with the reaction temperature reaching up to 1200 ℃.
基金financially supported by the National Key R&D Program of China(No.2024YFE0108800/T24KITG014)the National Natural Science Foundation of China(No:52475411)the International Partnership Program of Chinese Academy of Sciences(No.172GJHZ2022096FN)。
文摘Taking half-tube part with curvature as an example,the Impact Hydroforming(IHF)characteristics were studied by combining the actual forming experiment and numerical simulation.The IHF experiment showed that wrinkles appeared at the bottom of the part during single-step forming,but no wrinkles were observed during double-step forming.The thinning rate and deviation of the wall thickness of the part in each area were less than 20%and 2.7 mm,correspondingly,and the drawing depth of the part reached 45.8 mm.The effect of double-step forming was better than that of single-step forming,which was related to the IHF forming law.Besides,the characteristics of the IHF process were studied by numerical simulation.The results indicated that when double-step forming was utilized,there was almost no velocity field in the opposite direction of deformation after the bottom of the part contacted the die,and the existence of stress state at the bottom would restrain and eliminate the wrinkles.The inertia effect evolved with the driving pressure.Specially,the inertia effect can improve the flow of metal and reduce the deviation of the wall thickness of the part under double-step forming.
基金the supports of the National Natural Science Foundation of China(Grant No.52375378)。
文摘The multi-pass intermittent local loading process,which features a more flexible processing path,can further enhance the second material distribution during local loading,improve the formability of components,and reduce forming loads.However,the absence of compatible forming equipment makes it difficult to control the constraint in the unloaded zones during the forming process.This difficulty complicates coordination and control of deformation,particularly for asymmetric rib-web components.Additionally,the current implementation involves multi-fire heating,a long process flow,and high energy consumption,which limits the popularization and application of the local loading process.In this study,a new multi-pass local loading hydraulic forming apparatus that can quickly and reliably switch between heavy-load deformation and low-load constraint for different local loading sub-dies was developed.A 10-tonne laboratory prototype was developed,and the forming characteristics during the forming process as well as the response characteristics of the hydraulic system during the multi-pass intermittent local loading of rib-web component were investigated using numerical simulations and physical experiments.Results indicated that,compared to a whole loading process with the same initial geometry of billet,the total forming load(i.e.,the sum of loaded and restrained loads)is reduced by more than 40%with the local loading process,and by nearly 50%with multi-pass local loading.The multi-pass local loading process allows for more effective control of material flow compared to single-pass local loading,leading to improved cavity filling and reduced flow line disturbance.For a large-scale,complex titanium alloy bulkhead,the cavity filling problem was addressed by optimizing the multi-pass local loading path with an unequal thickness billet.The dynamic performance of the multi-pass local loading hydraulic system was found to be robust,with stable pressure transitions during motion and load switching for the sub-die(s).The dynamic characteristic of the hydraulic cylinder when switching from non-moving/unloaded state to a moving/loading state are consistent whether a load is present or not.However,the dynamic characteristics differ when switching from a moving/loading state to non-moving/unloaded state,showing opposite behavior.The developed hydraulic drive mechanism provides a way for implementation of multi-pass local loading without auxiliary operation and extra heating.The results of the study provide a foundation for the industrial production of large-scale,complex components with reduced force requirement and low-energy consumption.
基金Supported by National Natural Science Foundation of China(Grant Nos.52422510,52373320,52175360,50725517)the Young Elite Scientists Sponsorship Program by China Association for Science and Technology(Grant No.2021QNRC001)+1 种基金the Key R&D Program of Hubei Province(Grant No.2024BAB080)Natural Science Foundation of Wuhan(Grant No.2024040801020257).
文摘In aerospace,nuclear power,and new energy vehicles industries,utilizing integrated metal components with extreme sizes and/or structures is crucial for achieving significant weight-saving,performance-improvement,and excellent reliability.These components,made from metal sheets,rings,or tubes,exhibit characteristics like ultra-thin,ultra-thick,ultra-large,ultra-long,ultra-high ribs,and large variable diameters.During plastic de-formation in metal forming processes,defects such as ruptures,wrinkles,excessive strain differences,and un-expected weak performance areas are likely to occur due to the intersection of multiple effects in different research disciplines,including materials science,processes,and mechanics of materials.Consequently,the smooth forming of integrated parts is difficult.It is the first time to review,summarize,and analyze the ad-vancement of forming methods for producing integrated parts with extreme sizes and structures.The general academic ideas to change the process conditions and sequences to optimize stress state and improve plastic deformation ability for forming the components with extreme sizes/structures are introduced.Practical ex-amples,discussed in detail in the paper,include the forming of(i)integrated ultra-thin and ultra-thick sheet components;(ii)integrated ultra-large size ring components with thin wall and high ribs;and(iii)integrated ultra-long tube components with large perimeter difference.Various plasticity technologies and process se-quences have been developed.The key processes and applications of the technologies are discussed in detail,which achieve successful plastic forming of integrated components.This paper provides state-of-the-art and perspectives for the rapidly advancing material forming fields of key metal components for the next generation of equipment.
基金This work was supported by the Brain Korea 2lProject and the Grallt of Post-Doc Program, KyungpookNational University (1999).
文摘Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic FEM code has been developed. Isothermal forging process of a cylindrical housing has been simulated. The simulation results show that the given techniques and the FEM code are reasonable and feasible for three-dimensional bulk forming processes.
基金supported by the Natural Science Foundation of Shandong Province(ZR2022MB019,ZR2021MB134)the National Natural Science Foundation of China(22008131,51974086)。
文摘The dispersibility of active components in hydrodesulfurization(HDS)catalysts significantly influences the corresponding catalytic performance.In this study,sugar-based materials(glucose,chitosan,soluble starch,and corn starch)were utilized to prepare CoMo bulk HDS catalysts through a sugar foaming process.The foaming intermediates were analyzed using TG,FTIR,and Raman techniques to investigate the pyrolysis and carbonization process,revealing the presence of graphitic carbon in the 3 DPG,3 DPSS,and 3 DPCS catalysts even after calcination in an air atmosphere.The catalysts were further characterized using SEM,XRD,TEM,low-temperature N_(2) physical adsorption,and XPS.The 3 DPSS catalyst exhibited a thiophene conversion of 94.8%at 360℃ and 1 MPa,which could be ascribed to its unique three-dimensional pore structure,high dispersion of MoS_(2)(0.21),and high fraction of Mo^(4+)(83.14%).This study demonstrates the potential of using the sugar foaming technique to develop highly efficient HDS catalysts and provides new insights into the relationship between the physicochemical properties of the obtained catalysts and their catalytic performance.
基金financially supported by the National Natural Science Foundation of China(Nos.21876164 and U2030203)A Project Funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions。
文摘To address the poor mechanical properties of polydimethylsiloxane(PDMS)and enhance the understanding of the reinforcement mechanisms of aerogel network structures in rubber matrices,this study reinforced PDMS using an ordered interconnected three-dimensional montmorillonite(MMT)aerogel network.The average pore diameter of the aerogels was successfully reduced from 11.53μm to 2.51μm by adjusting the ratio of poly(vinyl alcohol)(PVA)to MMT via directional freezing.Changes in the aerogel network were observed in field emission scanning electron microscope(FESEM)images.After vacuum impregnation,the aerogel network structure of the composites was observed using FESEM.Tensile tests indicated that as the pore diameter decreased,the elongation at break of the composites first increased to a peak of329.61%before decreasing,while the tensile strength and Young's modulus continuously increased to their maximum values of 6.29 MPa and24.67 MPa,respectively.Meanwhile,FESEM images of the tensile cracks and fracture surfaces showed that with a reduction in aerogel pore diameter,the degrees of crack deflection and interfacial debonding increased,presenting a rougher fracture surface.These phenomena enable the composites to dissipate substantial energy during tension,thus effectively improving the mechanical strength of the composites.The present work elucidates the bearing of ordered three-dimensional aerogel network structures on the performance of rubber matrices and provides crucial theoretical insights and technical guidance for the creation and optimization of high-performance PDMS-based composites.
基金supported by the National Natural Science Foundation of China(Grant No.61773142).
文摘Intercepting high-maneuverability hypersonic targets in near-space environments poses significant challenges due to their extreme speeds and evasive capabilities.To address these challenges,this study presents an integrated approach that combines a Three-Dimensional Finite-Time Optimal Cooperative Guidance Law(FTOC)with an Information Fusion Anti-saturation Predefined-time Observer(IFAPO).The proposed FTOC guidance law employs a nonlinear,non-quadratic finite-time optimal control strategy designed for rapid convergence within the limited timeframes of near-space interceptions,avoiding the need for remaining flight time estimation or linear decoupling inherent in traditional methods.To complement the guidance strategy,the IFAPO leverages multi-source information fusion theory and incorporates anti-saturation mechanisms to enhance target maneuver estimation.This method ensures accurate and real-time prediction of target acceleration while maintaining predefined convergence performance,even under complex interception conditions.By integrating the FTOC guidance law and IFAPO,the approach optimizes cooperative missile positioning,improves interception success rates,and minimizes fuel consumption,addressing practical constraints in military applications.Simulation results and comparative analyses confirm the effectiveness of the integrated approach,demonstrating its capability to achieve cooperative interception of highly maneuvering targets with enhanced efficiency and reduced economic costs,aligning with realistic combat scenarios.
基金supported by the Project of the National Key Research and Development Program of China under Grant 2022YFB2404100。
文摘The internal hotspot temperature rise prediction in nanocrystalline high-frequency transformers(nanoHFTs) is essential to ensure reliable operation. This paper presents a three-dimensional thermal network(3DTN) model for epoxy resin encapsulated nano HFTs, which aims to precisely predict the temperature distribution inside the transformer in combination with the finite element method(FEM). A magnetothermal bidirectional coupling 3DTN model is established by analyzing the thermal conduction between the core, windings, and epoxy resin, while also considering the convection and radiation heat transfer mechanisms on the surface of the epoxy resin. The model considers the impact of loss distribution in the core and windings on the temperature field and adopts a simplified 1/2 thermal network model to reduce computational complexity. Furthermore, the results of FEM are compared with experimental results to verify the accuracy of the 3DTN model in predicting the temperature rise of nano HFT. The results show that the 3DTN model reduces errors by an average of 5.25% over the traditional two-dimensional thermal network(2DTN) model, particularly for temperature distributions in the windings and core. This paper provides a temperature rise prediction method for the thermal design and offers a theoretical basis and engineering guidance for the optimization of their thermal management systems.
文摘The rational design of efficient and stable carbon-based electrocatalysts for oxygen reduction and oxygen evolution reactions is crucial for improving energy density and long-term stability of rechargeable zinc-air batteries(ZABs).Herein,a general and controllable synthesis method was developed to prepare three-dimensional(3D)porous carbon composites embedded with diverse metal phosphide nanocrystallites by interfacial coordination of transition metal ions with phytic acid-doped polyaniline networks and subsequent pyrolysis.Phytic acid as the dopant of polyaniline provides favorable anchoring sites for metal ions owing to the coordination interaction.Specifically,adjusting the concentration of adsorbed cobalt ions can achieve the phase regulation of transition metal phosphides.Thus,with abundant cobalt phosphide nanoparticles and nitrogen-and phosphorus-doping sites,the obtained carbon-based electrocatalysts exhibited efficient electrocatalytic activities toward oxygen reduction and evolution reactions.Consequently,the fabricated ZABs exhibited a high energy density,high power density of 368 mW cm^(-2),and good cycling/mechanical stability,which could power water splitting for integrated device fabrication with high gas yields.
基金Projects(51205072,51275099)supported by the National Natural Science Foundation of ChinaProjects(S2013010013469,S2011040004110)supported by the Natural Science Foundation of Guangdong Province,China+1 种基金Projects(Yq2013127,2013KJCX0143)supported by Research Program of Guangdong Province UniversityProject(2012A083)supported by Guangzhou Prefecture University Research Program,China
文摘To improve heat-transfer performance, a novel integral three-dimensional fin-structure on the plat surface was presented to increase the evaporation efficiency. The three-dimensional fin-structure is composed of a spiral micro-groove and multi radial micro-grooves. Both ploughing-extrusion(P-E) and stamping were used to form the integral-fins with a connection between radial and circumferential directions. Based on the SEM results, the relationships among P-E speed v P-E, rotational speed np and feed fp, and among interference length Li, stamping feed angle θc and stamping depth ac were analyzed. The effects of processing parameters on the groove morphology and the matching relationship between parameters were also discussed. The integral finned surface with micro-grooves and cracks can be obtained under such processing conditions: P-E depth ap=0.3 mm, ac=0.3 mm, the interval of helical groove dp=1.24 mm, θc=2° and np=50 r/min.
基金supported by the National Natural Science Foundation of China(21325731,21221004 and 51478241)~~
文摘Three-dimensional（3D）ordered mesoporous MnO2 was prepared using KIT-6 mesoporous molecular sieves as a hard template.The material was used for catalytic oxidation of HCHO.The material has high surface areas and the mesoporous characteristics of the template,with cubic symmetry（ia3d）.It consists of a β-MnO2 crystalline phase corresponding to pyrolusite,with a rutile structure.Transmission electron microscopy and X-ray photoelectron spectroscopy showed that the 3D-MnO2 catalyst has a large number of exposed Mn4＋ ions on the（110）crystal plane surfaces,with a lattice spacing of 0.311 nm; this enhances oxidation of HCHO.Complete conversion of HCHO to CO2 and H2O was achieved at 130 °C on 3D-MnO2; the same conversions on α-MnO2 and β-MnO2 nanorods were obtained at 140 and 180 °C,respectively,under the same conditions.The specific mesoporous structure,high specific surface area,and large number of surface Mn4＋ ions are responsible for the catalytic activity of 3D-MnO2 in HCHO oxidation.
基金supported by the National Natural Science Foundation of China(21177160,21303263,21477164)Beijing Nova Program(Z141109001814072)+1 种基金Specialized Research Fund for the Doctoral Program of High Education of China(20130007120011)the Science Foundation of China University of Petroleum-Beijing(2462013YJRC13,2462013BJRC003)~~
文摘A series of K-doped Mn0.5Ce0.5Oδ （K-MCO） catalysts with three-dimensionally ordered macroporous （3DOM） structure and different K loadings were successfully synthesized using simple methods. These catalysts exhibited well-defined 3DOM nanostructure, which consisted of extensive interconnecting networks of spherical voids. The effects of the calcination temperature and calcination time on the morphological characteristics and crystalline forms of the catalysts were systematically studied. The catalysts showed high catalytic activity for the combustion of soot. 3DOM 20% K-MCO-4h catalyst, in particular, showed the highest catalytic activity of all of the catalysts studied （e.g., Ts0 = 331 ~C and Smco2 = 95.3%）. The occurrence of structural and synergistic effects among the K, Mn, and Ce atoms in the catalysts was favorable for enhancing their catalytic activity towards the combustion of diesel soot. Furthermore, the temperatures required for the complete combustion of the soot （〈400 ℃） were well within the exhaust temperature range （175-400 ℃）, which means that the accumulated soot can be removed under the conditions of the diesel exhaust gas. These catalysts could therefore be used in numerous practical applications because they are easy to synthesize, exhibit high catalytic activity, and can be made from low cost materials.
基金Project(51274250)supported by the National Natural Science Foundation of ChinaProject(2012BAK09B02-05)supported by the National Key Technology R&D Program during the 12th Five-year Plan of China
文摘An integration processing system of three-dimensional laser scanning information visualization in goaf was developed. It is provided with multiple functions, such as laser scanning information management for goaf, cloud data de-noising optimization, construction, display and operation of three-dimensional model, model editing, profile generation, calculation of goaf volume and roof area, Boolean calculation among models and interaction with the third party soft ware. Concerning this system with a concise interface, plentiful data input/output interfaces, it is featured with high integration, simple and convenient operations of applications. According to practice, in addition to being well-adapted, this system is favorably reliable and stable.
文摘Three-dimensional(3D)culture systems are becoming increasingly popular due to their ability to mimic tissue-like structures more effectively than the monolayer cultures.In cancer and stem cell research,the natural cell characteristics and architectures are closely mimicked by the 3D cell models.Thus,the 3D cell cultures are promising and suitable systems for various proposes,ranging from disease modeling to drug target identification as well as potential therapeutic substances that may transform our lives.This review provides a comprehensive compendium of recent advancements in culturing cells,in particular cancer and stem cells,using 3D culture techniques.The major approaches highlighted here include cell spheroids,hydrogel embedding,bioreactors,scaffolds,and bioprinting.In addition,the progress of employing 3D cell culture systems as a platform for cancer and stem cell research was addressed,and the prominent studies of 3D cell culture systems were discussed.
基金financial support of Distinguished scholars of yueqi (NO. 800015Z1179)National Science Fund subsidized project (51474220)Basic scientific research project of the CPC Central Committee (NO. 2009QZ03)
文摘Using self-researched gas drainage borehole stability dynamic monitoring device, three-dimensional deformation characteristics of borehole under steady vertical load were researched experimentally and systematically. This research indicated that under the action of steady loading, the mechanical deformation path of the simulated gas drainage borehole is gradually complicated, and the decay of the borehole circumferential strain is an important characterization of the prediction and early warning of borehole instability and collapse. The horizontal position of borehole occurs compressive strain, and the vertical of which occurs tensile strain under the action of vertical stress. At the initial stage of loading, the vertical strain is more sensitive than that in the horizontal direction. After a certain period of time, the horizontal strain is gradually higher than the vertical one, and the intersection of the borehole horizontal diameter and the hole wall is the stress concentration point. With the increase of the depth of hole, the strain shows a gradual decay trend as a whole, and the vertical strain decays more observably, but there is no absolute position correlation between the amount of strain decay and the increase in borehole depth,and the area within 1.5 times the orifice size is the borehole stress concentration zone.
文摘To address the problem of multi-missile cooperative interception against maneuvering targets at a prespecified impact time and desired Line-of-Sight(LOS)angles in ThreeDimensional(3D)space,this paper proposes a 3D leader-following cooperative interception guidance law.First,in the LOS direction of the leader,an impact time-controlled guidance law is derived based on the fixed-time stability theory,which enables the leader to complete the interception task at a prespecified impact time.Next,in the LOS direction of the followers,by introducing a time consensus tracking error function,a fixed-time consensus tracking guidance law is investigated to guarantee the consensus tracking convergence of the time-to-go.Then,in the direction normal to the LOS,by combining the designed global integral sliding mode surface and the second-order Sliding Mode Control(SMC)theory,an innovative 3D LOS-angle-constrained interception guidance law is developed,which eliminates the reaching phase in the traditional sliding mode guidance laws and effectively saves energy consumption.Moreover,it effectively suppresses the chattering phenomenon while avoiding the singularity issue,and compensates for unknown interference caused by target maneuvering online,making it convenient for practical engineering applications.Finally,theoretical proof analysis and multiple sets of numerical simulation results verify the effectiveness,superiority,and robustness of the investigated guidance law.
文摘This study assessed the clinical application of transvaginal three-dimensional ultrasound （3D TVUS） in the diagnosis of congenital uterine malformation. A retrospective study was performed on 62 patients with congenital uterine malformation confirmed hysteroscopically and/or laparoscopically. The patients were subjected to transvaginal two-dimensional ultrasound （2D TVUS） and 3D TVUS. The accuracy rate was compared between the two methods. The accuracy rate of 3D TVUS was （98.38%, 61/62）, higher than that of 2D TVUS （80.65%, 50/62）. 3D TVUS coronal plane imaging could demon- strate the internal shape of the endometrial cavity and the external contour of the uterine fundus. It al- lowed accurate measurement on the coronary plane, and could three-dimensionally show the image of cervical tube, thereby providing information for the diagnosis of some complex uterine malformation. 3D TVUS imaging can obtain comprehensive information of the uterus malformation, and it is superior to 2D TVUS for the diagnosis of congenital uterine malformations, especially complex uterine anomaly.
基金supported by the National Key R&D Program of China(No.2022YFB3104502)the National Natural Science Foundation of China(No.62301251)+2 种基金the Natural Science Foundation of Jiangsu Province of China under Project(No.BK20220883)the open research fund of National Mobile Communications Research Laboratory,Southeast University,China(No.2024D04)the Young Elite Scientists Sponsorship Program by CAST(No.2023QNRC001).
文摘The environment of low-altitude urban airspace is complex and variable due to numerous obstacles,non-cooperative aircraft,and birds.Unmanned Aerial Vehicles(UAVs)leveraging environmental information to achieve three-dimension collision-free trajectory planning is the prerequisite to ensure airspace security.However,the timely information of surrounding situation is difficult to acquire by UAVs,which further brings security risks.As a mature technology leveraged in traditional civil aviation,the Automatic Dependent Surveillance-Broadcast(ADS-B)realizes continuous surveillance of the information of aircraft.Consequently,we leverage ADS-B for surveillance and information broadcasting,and divide the aerial airspace into multiple sub-airspaces to improve flight safety in UAV trajectory planning.In detail,we propose the secure Sub-airSpaces Planning(SSP)algorithm and Particle Swarm Optimization Rapidly-exploring Random Trees(PSO-RRT)algorithm for the UAV trajectory planning in law-altitude airspace.The performance of the proposed algorithm is verified by simulations and the results show that SSP reduces both the maximum number of UAVs in the sub-airspace and the length of the trajectory,and PSO-RRT reduces the cost of UAV trajectory in the sub-airspace.
