To address the poor mechanical properties of polydimethylsiloxane(PDMS)and enhance the understanding of the reinforcement mechanisms of aerogel network structures in rubber matrices,this study reinforced PDMS using an...To address the poor mechanical properties of polydimethylsiloxane(PDMS)and enhance the understanding of the reinforcement mechanisms of aerogel network structures in rubber matrices,this study reinforced PDMS using an ordered interconnected three-dimensional montmorillonite(MMT)aerogel network.The average pore diameter of the aerogels was successfully reduced from 11.53μm to 2.51μm by adjusting the ratio of poly(vinyl alcohol)(PVA)to MMT via directional freezing.Changes in the aerogel network were observed in field emission scanning electron microscope(FESEM)images.After vacuum impregnation,the aerogel network structure of the composites was observed using FESEM.Tensile tests indicated that as the pore diameter decreased,the elongation at break of the composites first increased to a peak of329.61%before decreasing,while the tensile strength and Young's modulus continuously increased to their maximum values of 6.29 MPa and24.67 MPa,respectively.Meanwhile,FESEM images of the tensile cracks and fracture surfaces showed that with a reduction in aerogel pore diameter,the degrees of crack deflection and interfacial debonding increased,presenting a rougher fracture surface.These phenomena enable the composites to dissipate substantial energy during tension,thus effectively improving the mechanical strength of the composites.The present work elucidates the bearing of ordered three-dimensional aerogel network structures on the performance of rubber matrices and provides crucial theoretical insights and technical guidance for the creation and optimization of high-performance PDMS-based composites.展开更多
Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade compone...Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.展开更多
Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal...Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal mechanisms(MRMs)involved in the machining of PRMMCs.This paper develops a three-dimensional(3D)microstructure-based model for investigating the MRM and surface integrity of machined PRMMCs.To accurately mimic the actual microstructure of a PRMMC,polyhedrons were randomly distributed inside the matrix to represent irregular SiC particles.Particle fracture and matrix deformation and failure were taken into account.For the model’s capability comparison,a two-dimensional(2D)analysis was also conducted.Relevant cutting experiments showed that the established 3D model accurately predicted the material removal,chip morphology,machined surface finish,and cutting forces.It was found that the matrix-particle-tool interactions led to particle fractures,mainly in the primary shear and secondary deformation zones along the cutting path and beneath the machined surface.Particle fracture and dilodegment greatly influences the quality of a machined surface.It was also found that although a 2D model can reflect certain material removal features,its ability to predict microstructural variation is limited.展开更多
The development of graphene-based composites with low density,robust absorption,wide bandwidth and thin thickness remained a great challenge in the field of electromagnetic(EM)absorption.In this work,nitrogen-doped re...The development of graphene-based composites with low density,robust absorption,wide bandwidth and thin thickness remained a great challenge in the field of electromagnetic(EM)absorption.In this work,nitrogen-doped reduced graphene oxide/hollow cobalt ferrite(NRGO/hollow CoFe_(2)O_(4))composite aerogels were constructed by a solvothermal and hydrothermal two-step route.Results demonstrated that the as-fabricated composite aerogels had the ultralow density and a unique three-dimensional(3D)network structure,and lots of hollow CoFe_(2)O_(4)microspheres were almost homogeneously distributed on the wrinkled surfaces of lamellar NRGO.Moreover,superior EM absorbing capacity could be achieved by modulating the ferrite structure,addition amounts of hollow CoFe_(2)O_(4)and thicknesses.It was noteworthy that the NRGO/hollow CoFe_(2)O_(4)composite aerogel with the addition amount of ferrite of 15.0 mg pos-sessed the minimum reflection loss of-44.7 dB and maximum absorption bandwidth of 5.2 GHz(from 12.6 to 17.8 GHz)at a very thin thickness of 1.8 mm and filling ratio of 15.0 wt.%.Furthermore,the possible EM attenuation mechanism had been proposed.The results of this work would be helpful for developing RGO-based 3D composites as lightweight,thin and highly efficient EM wave absorbers.展开更多
As a two-dimensional(2D)material,graphene shows excellent advantages in the field of gas sensors due to its inherent large specific surface area and unique electrical properties.However,in the practical application of...As a two-dimensional(2D)material,graphene shows excellent advantages in the field of gas sensors due to its inherent large specific surface area and unique electrical properties.However,in the practical application of gas detection,graphene sheet is easy to form irreversible agglomeration and has some limitations such as low sensitivity,long response time and slow recovery speed,which greatly reduce its gas sensing performance.As a gas sensing material,three-dimensional(3D)porous graphene has been extensively studied in recent years owing to its larger specific surface area and stable structure.In order to synthesize graphene with different three-dimensional structures,many methods have been developed.Herein,the synthesis and assembly of three-dimensional graphene and its composites were reviewed,with emphasis on the application of three-dimensional graphene and its composites in the field of gas sensors.The challenges and development prospects of three-dimensional graphene materials in the application of gas sensors were briefly described.展开更多
Polyvinyl alcohol hydrogels have been used in wearable devices due to their good flexibility and biocompatibility.However,due to the low thermal conductivity(κ)of pure hydrogel,its further application in high power d...Polyvinyl alcohol hydrogels have been used in wearable devices due to their good flexibility and biocompatibility.However,due to the low thermal conductivity(κ)of pure hydrogel,its further application in high power devices is limited.To solve this problem,melamine sponge(MS)was used as the skeleton to wrap boron nitride nanosheets(BNNS)through repeated layering assembly,successfully preparing a three-dimensional(3D)boron nitride network(BNNS@MS),and PVA hydrogels were formed in the pores of the network.Due to the existence of the continuous phonon conduction network,the BNNS@MS/PVA exhibited an improvedκ.When the content of BNNS is about 6 wt.%,κof the hydrogel was increased to 1.12 W m^(-1)K^(-1),about two times higher than that of pure hydrogel.The solid heat conduction network and liquid convection network cooperate to achieve good thermal management ability.Combined with its high specific heat capacity,the composites have an important application prospect in the field of wearable flexible electronic thermal management.展开更多
The 2D limit equilibrium method is widely used for slope stability analysis.However,with the advancement of dump engineering,composite slopes often exhibit significant 3D mechanical effects.Consequently,it is of signi...The 2D limit equilibrium method is widely used for slope stability analysis.However,with the advancement of dump engineering,composite slopes often exhibit significant 3D mechanical effects.Consequently,it is of significant importance to develop an effective 3D stability calculation method for composite slopes to enhance the design and stability control of open-pit slope engineering.Using the composite slope formed by the mining stope and inner dump in Baiyinhua No.1 and No.2 open-pit coal mine as a case study,this research investigates the failure mode of composite slopes and establishes spatial shape equations for the sliding mass.By integrating the shear resistance and sliding force of each row of microstrip columns onto the bottom surface of the strip corresponding to the main sliding surface,a novel 2D equivalent physical and mechanical parameters analysis method for the strips on the main sliding surface of 3D sliding masses is proposed.Subsequently,a comprehensive 3D stability calculation method for composite slopes is developed,and the quantitative relationship between the coordinated development distance and its 3D stability coefficients is examined.The analysis reveals that the failure mode of the composite slope is characterized by cutting-bedding sliding,with the arc serving as the side interface and the weak layer as the bottom interface,while the destabilization mechanism primarily involves shear failure.The spatial form equation of the sliding mass comprises an ellipsoid and weak plane equation.The analysis revealed that when the coordinated development distance is 1500 m,the error rate between the 3D stability calculation result and the 2D stability calculation result of the composite slope is less than 8%,thereby verifying the proposed analytical method of equivalent physical and mechanical parameters and the 3D stability calculation method for composite slopes.Furthermore,the3D stability coefficient of the composite slope exhibits an exponential correlation with the coordinated development distance,with the coefficient gradually decreasing as the coordinated development distance increases.These findings provide a theoretical guideline for designing similar slope shape parameters and conducting stability analysis.展开更多
Silica fibers-reinforced, fused silica composites were fabricated with repeated vacuum-assisted liquid-phase infiltration. The mechanical properties, thermal properties, and ablative properties of the samples were eva...Silica fibers-reinforced, fused silica composites were fabricated with repeated vacuum-assisted liquid-phase infiltration. The mechanical properties, thermal properties, and ablative properties of the samples were evaluated. The effect of the silica fiber content and treatment temperature on the flexural strength of the three-dimensional SiO2 （3-D SiO2） composites also was investigated. The SiO2 composites show good mechanical properties and excellent ablative performance. The flexural strength increases with an increase in silica fiber content, and decreases with an increase in treatment temperature. When the volume fraction of the silica fiber is 50vo1% and the treatment temperature is 700℃ the flexural strength of the composites reaches a maximum value of 78 MPa. By adding cyclohexanone surfactant, the infiltration property can be largely improved, resulting in the density of SiO2 composites increasing up to 1.65 g/cm^3. The fracture surfaces of the flexural specimens observed using SEM, show that the pseudoplasticity and the toughening mechanisms of the composites are caused by absorption of a lot of energy by interface debonding and fiber pulling out.展开更多
As a thermosetting resin with excellent properties,epoxy resin is used in many areas such as electronics,transportation,aerospace,and other fields.However,its relatively low thermal conductivity limits its wide applic...As a thermosetting resin with excellent properties,epoxy resin is used in many areas such as electronics,transportation,aerospace,and other fields.However,its relatively low thermal conductivity limits its wide application in more demanding fields.Here,a three-dimensional carbon(3DC)network was prepared through NaCl template-assisted in situ chemical vapor deposition(CVD)and used to reinforce epoxy resin for enhancing its thermal conductivity.The 3DC was prepared with a molar ratio of sodium atom to carbon atom of 100:20,and argon atmosphere in CVD led to an optimal improvement in the thermal conductivity of epoxy resin.The thermal conductivity of epoxy resin increased by 18%when the filling content was 3 wt.%of 3DC network because of the high contact area,uniform dispersion,and enhanced formation of conductive paths with epoxy resin.As the amount of 3DC addition increases,the thermal conductivity of composites also increases.As an innovative exploration,the work presented in this paper is of great significance for the thermal conductivity application of epoxy resin in the future.展开更多
Three-dimensional( 3 D) fabric composite is a newly developed sandwich structure,consisting of two identical parallel fabric decks woven integrally and mechanically together by means of vertical woven fabrics. In this...Three-dimensional( 3 D) fabric composite is a newly developed sandwich structure,consisting of two identical parallel fabric decks woven integrally and mechanically together by means of vertical woven fabrics. In this paper,six types of 3 D fabric sandwich composites were developed in terms of compressive and flexural properties as a function of pile height( 10, 20 and30 mm) and pile distance( 16, 24 and 32 mm) in pile structures. The mechanical characteristics and the damage modes of the 3 D fabric sandwich composites under compressive and flexural load conditions were investigated. Besides,the influence of pile height and pile distance on the 3 D fabric sandwich composites mechanical properties was analyzed. The results showed that the compressive properties decreased with the increase of the pile height and the pile distance. Flexural properties increased with the increase of pile height, while decreased with the increase of pile distance.展开更多
The effects of fiber volume fraction on damping properties of carbon fiber three-dimensional and five-directional( 3D-5Dir)braided carbon fiber / epoxyres in composite cantilever beams were studied by experimental mod...The effects of fiber volume fraction on damping properties of carbon fiber three-dimensional and five-directional( 3D-5Dir)braided carbon fiber / epoxyres in composite cantilever beams were studied by experimental modal analysis method. Meanwhile,carbon fiber plain woven laminated / epoxy resin composites with different fiber volume fraction were concerned for comparison. The experimental result of braided specimens shows that the first three orders of natural frequency increase and the first three orders of the damping ratios of specimens decrease, when the fiber volume fraction increases. Furthermore,larger fiber volume fraction will be valuable for the better anti-exiting property of braided composites,and get an opposite effect on dissipation of vibration energy. The fiber volume fraction is an important factor for vibration performance design of braided composites. The comparison between the braided specimens and laminated specimens reveals that 3D braided composites have a wider range of damping properties than laminated composites with the same fiber volume fractions.展开更多
This work provides a method to predict the three-dimensional equivalent elastic properties of the filament-wound composites based on the multi-scale homogenization principle.In the meso-scale,a representative volume e...This work provides a method to predict the three-dimensional equivalent elastic properties of the filament-wound composites based on the multi-scale homogenization principle.In the meso-scale,a representative volume element(RVE)is defined and the bridging model is adopted to establish a theoretical predictive model for its three-dimensional equivalent elastic constants.The results obtained through this method for the previous experimental model are compared with the ones gained respectively by experiments and classical laminate theory to verify the reliability of this model.In addition,the effects of some winding parameters,such as winding angle,on the equivalent elastic behavior of the filament-wound composites are analyzed.The rules gained can provide a theoretical reference for the optimum design of filament-wound composites.展开更多
To improve the specific capacitance and rate capability of electrode material for supercapacitors, a three-dimensional graphene/polyaniline （3DGN/PANI） composite is prepared via in situ polymerization on GN hydrogel...To improve the specific capacitance and rate capability of electrode material for supercapacitors, a three-dimensional graphene/polyaniline （3DGN/PANI） composite is prepared via in situ polymerization on GN hydrogel. PANI grows on the GN surface as a thin film, and its content in the composite is controlled by the concentration of the reaction monomer. The specific capacitance of the 3DGN/PANI composite containing 10 wt% PANI reaches 322.8 F.g-1 at a current density of 1 A.g-1, nearly twice as large as that of the pure 3DGN （162.8 F.g-1）. The capacitance of the composite is 307.9 F.g-1 at 30 A.g-1 （maintaining 95.4%）, and 89% retention after 500 cycles. This study demonstrates the exciting potential of 3DGN/PANI with high capacitance, excellent rate capability and long cycling life for supercapacitors.展开更多
By making use of the direct integration method,an exact analysis of the general three-dimensional thermoelasticity problem is performed for the case of a transversely isotropic homogeneous half-space subject to local ...By making use of the direct integration method,an exact analysis of the general three-dimensional thermoelasticity problem is performed for the case of a transversely isotropic homogeneous half-space subject to local thermal and force loadings.The material plane of isotropy is assumed to be parallel to the limiting surface of the halfspace.By reducing the original thermoelasticity equations to the governing ones for individual stress-tensor components,the effect of material anisotropy in the stress field is analyzed with regard to the feasibility requirement,i.e.,the finiteness of the stress field at a distance from the disturbed area.As a result,the solution is constructed in the form of explicit analytical dependencies on the force and thermal loadings for various kinds of transversely isotropic materials and agrees with the basic principles of the continua mechanics.The solution can be efficiently used as a benchmark one for the direct computation of temperature and thermal stresses in transversely isotropic semi-infinite domains,as well as for the verification of solutions constructed by different means.展开更多
Three-dimensional(3D)braided composites with better properties have been used in some particular industries.Some have had obvious signs of crack when they are braided.Others have had catastrophic failures occuring wit...Three-dimensional(3D)braided composites with better properties have been used in some particular industries.Some have had obvious signs of crack when they are braided.Others have had catastrophic failures occuring without warning.A new methodology for the analysis of failure modes in composite materials by means of acoustic emission techniques has been developed.The occurrence of fiber-breakage during tensile loading tests has been observed by the acoustic emission technology.Using acoustic emission technology is investigated as a means of monitoring 3D braided composites structures,detecting damage,and predicting impending damage.Some of the findings of the research project were presented.展开更多
As one of China's national minorities, Tujia nationality has exerted an important role in the development course of modern national culture. In the development course of national culture of Tujia nationality, its ...As one of China's national minorities, Tujia nationality has exerted an important role in the development course of modern national culture. In the development course of national culture of Tujia nationality, its brocade art inherited generation by generation has been extensively applied in art inheritance in modern society. It has also been applied in practical teaching to manifest the unique style and special artistic expression of Tujia brocade art. Under such a context, it is necessary to strengthen analysis on its national characteristics in the art development course and art composition characteristics. For this purpose, this paper makes special analysis on the national characteristics and art composition of Tujia brocade art in the sequence of analysis on the basic components of Tujia brocade art, analysis on its national characteristics and then detailed analysis on its composition characteristics. The author hopes to help people to understand the unique characteristics and results of Tujia brocade art after the analysis in this paper.展开更多
United States Botanic Garden(USBG) was taken for example to systematically demonstrate the role of formal composition in garden landscape design.Application cases were used to analyze formal composition of plant lands...United States Botanic Garden(USBG) was taken for example to systematically demonstrate the role of formal composition in garden landscape design.Application cases were used to analyze formal composition of plant landscapes in USBG.Point plant landscapes lay the foundation of all other forms,concentrated and centripetal effects of which can form comparisons according to size of plant.Line is the trace of moving points,and linear plant landscapes indicate those formed by using thick,thin,long,short,square,round,curved and straight "lines".And surface plant landscapes are to form contrastive images or scenic areas by using plant clusters.Finally,concrete cases were given to analyze flowerpot selection and combination for creating point,linear and surface potted plant landscapes,and to provide detailed reference for the plant design of modern Chinese gardens.展开更多
This article observes the composition of Chinese gardening arts in light of philosophy,aesthetics of painting,stylistics and culture,and tries to explore the correlation between artistic composition and garden composi...This article observes the composition of Chinese gardening arts in light of philosophy,aesthetics of painting,stylistics and culture,and tries to explore the correlation between artistic composition and garden composition.展开更多
Three-dimensional graphene/conducting polymer（3DGCP） composites have received significant attention in recent years due to their unique structures and promising applications in energy storage.With the structural div...Three-dimensional graphene/conducting polymer（3DGCP） composites have received significant attention in recent years due to their unique structures and promising applications in energy storage.With the structural diversity of graphene and π-functional conducting polymers via rich chemical routes,a number of 3DGCP composites with novel structures and attractive performance have been developed.Particularly,the hierarchical porosity,the interactions between graphene and conducting polymers as well as the their synergetic effects within 3DGCP composites can be well combined and elaborated by various synthetic methods,which made 3DGCP composites show unique electrochemical properties and significantly improved performance in energy storage fields compared to other graphenebased composites.In this short review,we present recent advances in 3DGCP composites in developing effective strategies to prepare 3DGCP composites and exploring them as a unique platform for supercapacitors with unprecedented performance.The challenges and future opportunities are also discussed for promotion of further study.展开更多
Constructing three-dimensional(3D)foam-like structure in magnetic metal/carbon composites is regarded as a promising pathway to reinforce their electromagnetic(EM)functions.Herein,a nitrateassisted polymer-bubbling st...Constructing three-dimensional(3D)foam-like structure in magnetic metal/carbon composites is regarded as a promising pathway to reinforce their electromagnetic(EM)functions.Herein,a nitrateassisted polymer-bubbling strategy is reported for the synthesis of Co/carbon foams,which is simply accomplished by direct pyrolyzing the mixture of polyvinylpyrrolidone(PVP)and cobalt nitrate hexahydrate(Co(NO_(3))_(2)·6 H_(2) O).Co(NO_(3))_(2)·6H_(2)O not only plays as the source of Co nanoparticles,but also accounts for the formation of 3D microstructure through releasing gas.By manipulating the weight ratio of Co(NO_(3))_(2)·6H_(2)O to PVP,the chemical composition,microstructure,and EM properties of these composites can be easily regulated.When the weight ratio reaches 1.5,the resultant composite displays good microwave absorption performance,whose reflection loss intensity and effective absorption bandwidth are superior to those of many common Co/C composites.EM analysis reveals that such architecture is greatly helpful to establish cross-linked conductive networks in the wax matrix,resulting in powerful dielectric loss under low absorber loading.Meanwhile,3D microstructure is also beneficial for multiple reflections that equal to extend the transmission path of incident EM waves.Simple synthesis strategy and desirable properties of these magnetic carbon foams may render them as the low-cost substitute of 3D graphene for the application against EM pollution.展开更多
基金financially supported by the National Natural Science Foundation of China(Nos.21876164 and U2030203)A Project Funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions。
文摘To address the poor mechanical properties of polydimethylsiloxane(PDMS)and enhance the understanding of the reinforcement mechanisms of aerogel network structures in rubber matrices,this study reinforced PDMS using an ordered interconnected three-dimensional montmorillonite(MMT)aerogel network.The average pore diameter of the aerogels was successfully reduced from 11.53μm to 2.51μm by adjusting the ratio of poly(vinyl alcohol)(PVA)to MMT via directional freezing.Changes in the aerogel network were observed in field emission scanning electron microscope(FESEM)images.After vacuum impregnation,the aerogel network structure of the composites was observed using FESEM.Tensile tests indicated that as the pore diameter decreased,the elongation at break of the composites first increased to a peak of329.61%before decreasing,while the tensile strength and Young's modulus continuously increased to their maximum values of 6.29 MPa and24.67 MPa,respectively.Meanwhile,FESEM images of the tensile cracks and fracture surfaces showed that with a reduction in aerogel pore diameter,the degrees of crack deflection and interfacial debonding increased,presenting a rougher fracture surface.These phenomena enable the composites to dissipate substantial energy during tension,thus effectively improving the mechanical strength of the composites.The present work elucidates the bearing of ordered three-dimensional aerogel network structures on the performance of rubber matrices and provides crucial theoretical insights and technical guidance for the creation and optimization of high-performance PDMS-based composites.
基金Project supported by the National Natural Science Foundation of China(Nos.12372071 and 12372070)the Aeronautical Science Fund of China(No.2022Z055052001)the Foundation of China Scholarship Council(No.202306830079)。
文摘Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.
文摘Particulate-reinforced metal matrix composites(PRMMCs)are difficult to machine due to the inclusion of hard,brittle reinforcing particles.Existing experimental investigations rarely reveal the complex material removal mechanisms(MRMs)involved in the machining of PRMMCs.This paper develops a three-dimensional(3D)microstructure-based model for investigating the MRM and surface integrity of machined PRMMCs.To accurately mimic the actual microstructure of a PRMMC,polyhedrons were randomly distributed inside the matrix to represent irregular SiC particles.Particle fracture and matrix deformation and failure were taken into account.For the model’s capability comparison,a two-dimensional(2D)analysis was also conducted.Relevant cutting experiments showed that the established 3D model accurately predicted the material removal,chip morphology,machined surface finish,and cutting forces.It was found that the matrix-particle-tool interactions led to particle fractures,mainly in the primary shear and secondary deformation zones along the cutting path and beneath the machined surface.Particle fracture and dilodegment greatly influences the quality of a machined surface.It was also found that although a 2D model can reflect certain material removal features,its ability to predict microstructural variation is limited.
基金supported by the Foundation of Provincial Natural Science Research Project of Anhui Colleges(No.KJ2021ZD0047)the Anhui Provincial Natural Science Foundation(No.2008085J27)+1 种基金the China Postdoctoral Science Foundation(No.2019M652160)the Research Foundation of the Institute of Environment-friendly Materials and Occupational Health(Wuhu),Anhui University of Science and Technology(No.ALW2020YF05).
文摘The development of graphene-based composites with low density,robust absorption,wide bandwidth and thin thickness remained a great challenge in the field of electromagnetic(EM)absorption.In this work,nitrogen-doped reduced graphene oxide/hollow cobalt ferrite(NRGO/hollow CoFe_(2)O_(4))composite aerogels were constructed by a solvothermal and hydrothermal two-step route.Results demonstrated that the as-fabricated composite aerogels had the ultralow density and a unique three-dimensional(3D)network structure,and lots of hollow CoFe_(2)O_(4)microspheres were almost homogeneously distributed on the wrinkled surfaces of lamellar NRGO.Moreover,superior EM absorbing capacity could be achieved by modulating the ferrite structure,addition amounts of hollow CoFe_(2)O_(4)and thicknesses.It was noteworthy that the NRGO/hollow CoFe_(2)O_(4)composite aerogel with the addition amount of ferrite of 15.0 mg pos-sessed the minimum reflection loss of-44.7 dB and maximum absorption bandwidth of 5.2 GHz(from 12.6 to 17.8 GHz)at a very thin thickness of 1.8 mm and filling ratio of 15.0 wt.%.Furthermore,the possible EM attenuation mechanism had been proposed.The results of this work would be helpful for developing RGO-based 3D composites as lightweight,thin and highly efficient EM wave absorbers.
基金financially supported by the Graduate Scientific Research and Innovation Foundation of Chongqing,China(No.CYS20001)。
文摘As a two-dimensional(2D)material,graphene shows excellent advantages in the field of gas sensors due to its inherent large specific surface area and unique electrical properties.However,in the practical application of gas detection,graphene sheet is easy to form irreversible agglomeration and has some limitations such as low sensitivity,long response time and slow recovery speed,which greatly reduce its gas sensing performance.As a gas sensing material,three-dimensional(3D)porous graphene has been extensively studied in recent years owing to its larger specific surface area and stable structure.In order to synthesize graphene with different three-dimensional structures,many methods have been developed.Herein,the synthesis and assembly of three-dimensional graphene and its composites were reviewed,with emphasis on the application of three-dimensional graphene and its composites in the field of gas sensors.The challenges and development prospects of three-dimensional graphene materials in the application of gas sensors were briefly described.
基金the National Natural Science Foundation of China(Nos.52173078,52130303,and 51803151)the Young Elite Scientists Sponsorship Program by CAST(No.2019QNRC001)。
文摘Polyvinyl alcohol hydrogels have been used in wearable devices due to their good flexibility and biocompatibility.However,due to the low thermal conductivity(κ)of pure hydrogel,its further application in high power devices is limited.To solve this problem,melamine sponge(MS)was used as the skeleton to wrap boron nitride nanosheets(BNNS)through repeated layering assembly,successfully preparing a three-dimensional(3D)boron nitride network(BNNS@MS),and PVA hydrogels were formed in the pores of the network.Due to the existence of the continuous phonon conduction network,the BNNS@MS/PVA exhibited an improvedκ.When the content of BNNS is about 6 wt.%,κof the hydrogel was increased to 1.12 W m^(-1)K^(-1),about two times higher than that of pure hydrogel.The solid heat conduction network and liquid convection network cooperate to achieve good thermal management ability.Combined with its high specific heat capacity,the composites have an important application prospect in the field of wearable flexible electronic thermal management.
基金supported by the National Natural Science Foundation of China (No.52374124)National Youth Science Foundation of China (No.52204135)+3 种基金Xing Liao Talent Plan (No.XLYC2202004)Young Elite Scientists Sponsorship Program by CAST (No.2023QNRC001)Liaoning Province International Science and Technology Cooperation Plan (No.2022JH2/1070004)Liaoning Natural Science Foundation Program (No.2022-BS-327)。
文摘The 2D limit equilibrium method is widely used for slope stability analysis.However,with the advancement of dump engineering,composite slopes often exhibit significant 3D mechanical effects.Consequently,it is of significant importance to develop an effective 3D stability calculation method for composite slopes to enhance the design and stability control of open-pit slope engineering.Using the composite slope formed by the mining stope and inner dump in Baiyinhua No.1 and No.2 open-pit coal mine as a case study,this research investigates the failure mode of composite slopes and establishes spatial shape equations for the sliding mass.By integrating the shear resistance and sliding force of each row of microstrip columns onto the bottom surface of the strip corresponding to the main sliding surface,a novel 2D equivalent physical and mechanical parameters analysis method for the strips on the main sliding surface of 3D sliding masses is proposed.Subsequently,a comprehensive 3D stability calculation method for composite slopes is developed,and the quantitative relationship between the coordinated development distance and its 3D stability coefficients is examined.The analysis reveals that the failure mode of the composite slope is characterized by cutting-bedding sliding,with the arc serving as the side interface and the weak layer as the bottom interface,while the destabilization mechanism primarily involves shear failure.The spatial form equation of the sliding mass comprises an ellipsoid and weak plane equation.The analysis revealed that when the coordinated development distance is 1500 m,the error rate between the 3D stability calculation result and the 2D stability calculation result of the composite slope is less than 8%,thereby verifying the proposed analytical method of equivalent physical and mechanical parameters and the 3D stability calculation method for composite slopes.Furthermore,the3D stability coefficient of the composite slope exhibits an exponential correlation with the coordinated development distance,with the coefficient gradually decreasing as the coordinated development distance increases.These findings provide a theoretical guideline for designing similar slope shape parameters and conducting stability analysis.
文摘Silica fibers-reinforced, fused silica composites were fabricated with repeated vacuum-assisted liquid-phase infiltration. The mechanical properties, thermal properties, and ablative properties of the samples were evaluated. The effect of the silica fiber content and treatment temperature on the flexural strength of the three-dimensional SiO2 （3-D SiO2） composites also was investigated. The SiO2 composites show good mechanical properties and excellent ablative performance. The flexural strength increases with an increase in silica fiber content, and decreases with an increase in treatment temperature. When the volume fraction of the silica fiber is 50vo1% and the treatment temperature is 700℃ the flexural strength of the composites reaches a maximum value of 78 MPa. By adding cyclohexanone surfactant, the infiltration property can be largely improved, resulting in the density of SiO2 composites increasing up to 1.65 g/cm^3. The fracture surfaces of the flexural specimens observed using SEM, show that the pseudoplasticity and the toughening mechanisms of the composites are caused by absorption of a lot of energy by interface debonding and fiber pulling out.
基金the Key Projects of Tianjin Natural Science Foundation(No.16ZXCLGX00130).
文摘As a thermosetting resin with excellent properties,epoxy resin is used in many areas such as electronics,transportation,aerospace,and other fields.However,its relatively low thermal conductivity limits its wide application in more demanding fields.Here,a three-dimensional carbon(3DC)network was prepared through NaCl template-assisted in situ chemical vapor deposition(CVD)and used to reinforce epoxy resin for enhancing its thermal conductivity.The 3DC was prepared with a molar ratio of sodium atom to carbon atom of 100:20,and argon atmosphere in CVD led to an optimal improvement in the thermal conductivity of epoxy resin.The thermal conductivity of epoxy resin increased by 18%when the filling content was 3 wt.%of 3DC network because of the high contact area,uniform dispersion,and enhanced formation of conductive paths with epoxy resin.As the amount of 3DC addition increases,the thermal conductivity of composites also increases.As an innovative exploration,the work presented in this paper is of great significance for the thermal conductivity application of epoxy resin in the future.
基金National Key R&D Program of China(Nos.2016YFB0303104,2018YFC0810306)Jiangsu Overseas Visiting Scholar Program for University Prominent Younge Middle-aged Teachers and PresidentsSix Talent Peaks Project in Jiangsu Province,China(No.XCL-061)
文摘Three-dimensional( 3 D) fabric composite is a newly developed sandwich structure,consisting of two identical parallel fabric decks woven integrally and mechanically together by means of vertical woven fabrics. In this paper,six types of 3 D fabric sandwich composites were developed in terms of compressive and flexural properties as a function of pile height( 10, 20 and30 mm) and pile distance( 16, 24 and 32 mm) in pile structures. The mechanical characteristics and the damage modes of the 3 D fabric sandwich composites under compressive and flexural load conditions were investigated. Besides,the influence of pile height and pile distance on the 3 D fabric sandwich composites mechanical properties was analyzed. The results showed that the compressive properties decreased with the increase of the pile height and the pile distance. Flexural properties increased with the increase of pile height, while decreased with the increase of pile distance.
基金Tianjin Municipal Science and Technologies Commission,China(Nos.10SYSYJC27800,1ZCKFSF00500)
文摘The effects of fiber volume fraction on damping properties of carbon fiber three-dimensional and five-directional( 3D-5Dir)braided carbon fiber / epoxyres in composite cantilever beams were studied by experimental modal analysis method. Meanwhile,carbon fiber plain woven laminated / epoxy resin composites with different fiber volume fraction were concerned for comparison. The experimental result of braided specimens shows that the first three orders of natural frequency increase and the first three orders of the damping ratios of specimens decrease, when the fiber volume fraction increases. Furthermore,larger fiber volume fraction will be valuable for the better anti-exiting property of braided composites,and get an opposite effect on dissipation of vibration energy. The fiber volume fraction is an important factor for vibration performance design of braided composites. The comparison between the braided specimens and laminated specimens reveals that 3D braided composites have a wider range of damping properties than laminated composites with the same fiber volume fractions.
文摘This work provides a method to predict the three-dimensional equivalent elastic properties of the filament-wound composites based on the multi-scale homogenization principle.In the meso-scale,a representative volume element(RVE)is defined and the bridging model is adopted to establish a theoretical predictive model for its three-dimensional equivalent elastic constants.The results obtained through this method for the previous experimental model are compared with the ones gained respectively by experiments and classical laminate theory to verify the reliability of this model.In addition,the effects of some winding parameters,such as winding angle,on the equivalent elastic behavior of the filament-wound composites are analyzed.The rules gained can provide a theoretical reference for the optimum design of filament-wound composites.
基金Project supported by the National Basic Research Program of China(Grant Nos.2011CB932700 and 2011CB932703)the National Natural Science Foundation of China(Grant Nos.61335006,61378073,and 61077044)+1 种基金the Beijing Natural Science Foundation,China(Grant No.4132031)the Fundamental Research Funds for the Central Universities of Beijing Jiaotong University,China(Grant No.2014YJS136)
文摘To improve the specific capacitance and rate capability of electrode material for supercapacitors, a three-dimensional graphene/polyaniline （3DGN/PANI） composite is prepared via in situ polymerization on GN hydrogel. PANI grows on the GN surface as a thin film, and its content in the composite is controlled by the concentration of the reaction monomer. The specific capacitance of the 3DGN/PANI composite containing 10 wt% PANI reaches 322.8 F.g-1 at a current density of 1 A.g-1, nearly twice as large as that of the pure 3DGN （162.8 F.g-1）. The capacitance of the composite is 307.9 F.g-1 at 30 A.g-1 （maintaining 95.4%）, and 89% retention after 500 cycles. This study demonstrates the exciting potential of 3DGN/PANI with high capacitance, excellent rate capability and long cycling life for supercapacitors.
基金supported by Joint Fund of Advanced Aerospace Manufacturing Technology Research(No. U1937601)the partial financial support of this research by the budget program of Ukraine“Support for the Development of Priority Research Areas”(No.CPCEC 6451230)。
文摘By making use of the direct integration method,an exact analysis of the general three-dimensional thermoelasticity problem is performed for the case of a transversely isotropic homogeneous half-space subject to local thermal and force loadings.The material plane of isotropy is assumed to be parallel to the limiting surface of the halfspace.By reducing the original thermoelasticity equations to the governing ones for individual stress-tensor components,the effect of material anisotropy in the stress field is analyzed with regard to the feasibility requirement,i.e.,the finiteness of the stress field at a distance from the disturbed area.As a result,the solution is constructed in the form of explicit analytical dependencies on the force and thermal loadings for various kinds of transversely isotropic materials and agrees with the basic principles of the continua mechanics.The solution can be efficiently used as a benchmark one for the direct computation of temperature and thermal stresses in transversely isotropic semi-infinite domains,as well as for the verification of solutions constructed by different means.
基金Tianjin Natural Science Sustentation Fund Project,China(No.043600711)Ministry of Education Sustentation Fund Project,China(No.03008)
文摘Three-dimensional(3D)braided composites with better properties have been used in some particular industries.Some have had obvious signs of crack when they are braided.Others have had catastrophic failures occuring without warning.A new methodology for the analysis of failure modes in composite materials by means of acoustic emission techniques has been developed.The occurrence of fiber-breakage during tensile loading tests has been observed by the acoustic emission technology.Using acoustic emission technology is investigated as a means of monitoring 3D braided composites structures,detecting damage,and predicting impending damage.Some of the findings of the research project were presented.
文摘As one of China's national minorities, Tujia nationality has exerted an important role in the development course of modern national culture. In the development course of national culture of Tujia nationality, its brocade art inherited generation by generation has been extensively applied in art inheritance in modern society. It has also been applied in practical teaching to manifest the unique style and special artistic expression of Tujia brocade art. Under such a context, it is necessary to strengthen analysis on its national characteristics in the art development course and art composition characteristics. For this purpose, this paper makes special analysis on the national characteristics and art composition of Tujia brocade art in the sequence of analysis on the basic components of Tujia brocade art, analysis on its national characteristics and then detailed analysis on its composition characteristics. The author hopes to help people to understand the unique characteristics and results of Tujia brocade art after the analysis in this paper.
文摘United States Botanic Garden(USBG) was taken for example to systematically demonstrate the role of formal composition in garden landscape design.Application cases were used to analyze formal composition of plant landscapes in USBG.Point plant landscapes lay the foundation of all other forms,concentrated and centripetal effects of which can form comparisons according to size of plant.Line is the trace of moving points,and linear plant landscapes indicate those formed by using thick,thin,long,short,square,round,curved and straight "lines".And surface plant landscapes are to form contrastive images or scenic areas by using plant clusters.Finally,concrete cases were given to analyze flowerpot selection and combination for creating point,linear and surface potted plant landscapes,and to provide detailed reference for the plant design of modern Chinese gardens.
文摘This article observes the composition of Chinese gardening arts in light of philosophy,aesthetics of painting,stylistics and culture,and tries to explore the correlation between artistic composition and garden composition.
基金supported by The Program for Professor of Special Appointment(Eastern Scholar)at Shanghai Institutions of Higher Learning(No.TP2015002)the National Natural Science Foundation of China(No.51403099)
文摘Three-dimensional graphene/conducting polymer（3DGCP） composites have received significant attention in recent years due to their unique structures and promising applications in energy storage.With the structural diversity of graphene and π-functional conducting polymers via rich chemical routes,a number of 3DGCP composites with novel structures and attractive performance have been developed.Particularly,the hierarchical porosity,the interactions between graphene and conducting polymers as well as the their synergetic effects within 3DGCP composites can be well combined and elaborated by various synthetic methods,which made 3DGCP composites show unique electrochemical properties and significantly improved performance in energy storage fields compared to other graphenebased composites.In this short review,we present recent advances in 3DGCP composites in developing effective strategies to prepare 3DGCP composites and exploring them as a unique platform for supercapacitors with unprecedented performance.The challenges and future opportunities are also discussed for promotion of further study.
基金financially supported by the National Natural Science Foundation of China(Nos.21676065,21776053)。
文摘Constructing three-dimensional(3D)foam-like structure in magnetic metal/carbon composites is regarded as a promising pathway to reinforce their electromagnetic(EM)functions.Herein,a nitrateassisted polymer-bubbling strategy is reported for the synthesis of Co/carbon foams,which is simply accomplished by direct pyrolyzing the mixture of polyvinylpyrrolidone(PVP)and cobalt nitrate hexahydrate(Co(NO_(3))_(2)·6 H_(2) O).Co(NO_(3))_(2)·6H_(2)O not only plays as the source of Co nanoparticles,but also accounts for the formation of 3D microstructure through releasing gas.By manipulating the weight ratio of Co(NO_(3))_(2)·6H_(2)O to PVP,the chemical composition,microstructure,and EM properties of these composites can be easily regulated.When the weight ratio reaches 1.5,the resultant composite displays good microwave absorption performance,whose reflection loss intensity and effective absorption bandwidth are superior to those of many common Co/C composites.EM analysis reveals that such architecture is greatly helpful to establish cross-linked conductive networks in the wax matrix,resulting in powerful dielectric loss under low absorber loading.Meanwhile,3D microstructure is also beneficial for multiple reflections that equal to extend the transmission path of incident EM waves.Simple synthesis strategy and desirable properties of these magnetic carbon foams may render them as the low-cost substitute of 3D graphene for the application against EM pollution.
