The three-dimensional particle electrode system exhibits significant potential for application in the treatment of wastewater.Nonetheless,the advancement of effective granular electrodes characterized by elevated cata...The three-dimensional particle electrode system exhibits significant potential for application in the treatment of wastewater.Nonetheless,the advancement of effective granular electrodes characterized by elevated catalytic activity and minimal energy consumption continues to pose a significant challenge.In this research,Fluorine-doped copper-carbon(F/Cu-GAC)particle electrodes were effectively synthesized through an impregnationcalcination technique,utilizing granular activated carbon as the carrier and fluorinedoped modified copper oxides as the catalytic agents.The particle electrodes were subsequently utilized to promote the degradation of 2,4,6-trichlorophenol(2,4,6-TCP)in a threedimensional electrocatalytic reactor(3DER).The F/Cu-GAC particle electrodes were polarized under the action of electric field,which promoted the heterogeneous Fenton-like reaction in which H2O2 generated by two-electron oxygen reduction reaction(2e-ORR)of O_(2) was catalytically decomposed to·OH.The 3DER equipped with F/Cu-GAC particle electrodes showed 100%removal of 2,4,6-TCP and 79.24%removal of TOC with a specific energy consumption(EC)of approximately 0.019 kWh/g·COD after 2 h of operation.The F/Cu-GAC particle electrodes exhibited an overpotential of 0.38 V and an electrochemically active surface area(ECSA)of 715 cm^(2),as determined through linear sweep voltammetry(LSV)and cyclic voltammetry(CV)assessments.These findings suggest a high level of electrocatalytic performance.Furthermore,the catalytic mechanism of the 3DER equipped with F/Cu-GAC particle electrodes was elucidated through the application of X-ray photoelectron spectroscopy(XPS),electron spin resonance(ESR),and active species capture experiments.This investigation offers a novel approach for the effective degradation of 2,4,6-TCP.展开更多
This study focused on As(V)removal by electrosorption in a self-made three-dimensional electrode reactor,in which granular activated carbon(GAC)was used as the particle electrode.Under the optimal conditions,the remov...This study focused on As(V)removal by electrosorption in a self-made three-dimensional electrode reactor,in which granular activated carbon(GAC)was used as the particle electrode.Under the optimal conditions,the removal efficiency of As(V)was 84%,and its residual concentration in solution was 0.08 mg/L.From kinetic investigation,the rate determining steps of the entire process may involve more than two processes:membrane diffusion,material diffusion and physical/chemical adsorption processes.During the desorption process,As(V)can be desorbed from GAC,and the GAC was able to electro-adsorb As(V)again after desorption,which means that the electrode has good cycling performance.展开更多
The electrochemical degradation of reed pulp black liquor containing lignin pretreated by acidification method was investigated using a three-dimensional electrode reactor. Using activated carbon as particle electrode...The electrochemical degradation of reed pulp black liquor containing lignin pretreated by acidification method was investigated using a three-dimensional electrode reactor. Using activated carbon as particle electrode, the effects of p H value, reaction temperature, electrolysis time and current on residual concentration of total organic carbon(TOC) were discussed in detail. The optimal conditions were obtained: pH 2.5, influent flow rate of 200 mL/min, 25 °C, 300 mA and 2h of electrolysis time, and the removal efficiency of TOC maintains at 35.57 %. The results of the electrochemical method indicate that ·OH radicals are produced in activated carbon anode in the electrolysis process and then adsorbed on the activated carbon surface. Microcell consists of ·OH radicals and the absorbed lignin. With the microcell reaction, the lignin is degraded, while the anodic polarized curve illustrates that the lignin is obviously oxidized in the anode. The contributions of direct and indirect electrolyses to the TOC removal ratio are about 50%, respectively.展开更多
The use of three-dimensional(3D)electrodes in water treatment is competitive because of their high catalytic efficiency,low energy consumption and promising development.The use of particle electrodes is a key research...The use of three-dimensional(3D)electrodes in water treatment is competitive because of their high catalytic efficiency,low energy consumption and promising development.The use of particle electrodes is a key research focus in this technology.They are usually in the form of particles that fill the space between the cathode and anode,and the selection of materials used is important.Carbon-based materials are widely used because of their large specific surface area,good adsorption performance,high chemical stability and low cost.The principles of 3D electrode technology are introduced and recent research on its use for degrading organic pollutants using carbon-based particle electrodes is summarized.The classification of particle electrodes is introduced and the challenges for the future development of carbon-based particle electrodes in wastewater treatment are discussed.展开更多
Degradation of o-chloronitrobenzene wastewater was experimentally investigated at a three-dimensional electrode（TDE） with granular activated carbon as the particle electrode, graphite as the anode, and stainless ste...Degradation of o-chloronitrobenzene wastewater was experimentally investigated at a three-dimensional electrode（TDE） with granular activated carbon as the particle electrode, graphite as the anode, and stainless steel plate as the cathode. The kinetic model of o-chloronitrobenzene degradation was studied, and the effects of pH, electrolysis time, particle electrode, electrolyte concentration, and initial concentration of the solution on degradation efficiency were investigated to determine the optimal operating conditions. The degradation of o-chloronitrobenzene by oxidation at the TDE was monitored by chemical oxygen demand（COD） measurements, UV-Vis absorption, and high performance liquid chromatography（HPLC）. COD degradation by electrochemical degradation followed pseudo-first order kinetics with respect to the concentration of o-chloronitrobenzene solutions. Optimal reaction conditions included 15 g of activated carbon as the particle electrode, 400 mg/L o-chloronitrobenzene solution containing 0.10 mol/L Na2SO4, pH=3, and 60 min of electrolysis. The UV-Vis absorption spectra and HPLC results illustrate that the benzene ring in o-chloronitrobenzene was rapidly broken down to form aliphatic substances through electrochemical degradation. COD degradation was approximately 98.5% at optimal conditions.展开更多
In order to increase the electrode surface area and enhance the charge storage capacity, we study the micro electro mechanical system technology to fabricate three-dimensional high aspect ratio micro-electrode structu...In order to increase the electrode surface area and enhance the charge storage capacity, we study the micro electro mechanical system technology to fabricate three-dimensional high aspect ratio micro-electrode structure based on glass. The anodic constant potential method is employed to deposit manganese oxide as electroactive substances on the micro-electrode surface. Cyclic voltammetry and constant current charge-discharge method are both used to prepare electrode electrochemical performance testing, with a two-dimensional electrode without structure for comparison. Experimental results show that three-dimensional elec- trode structure can effectively enhance the charge storage capacity. At 1.0 mA/cm2 charge- discharge density, the three-dimensional electrode shows a capacitance of 17.88 mF/cm2, seven times higher than the two-dimensional electrode.展开更多
Three-dimensional(3D)vertical architecture transistors represent an important technological pursuit,which have distinct advantages in device integration density,operation speed,and power consumption.However,the fabric...Three-dimensional(3D)vertical architecture transistors represent an important technological pursuit,which have distinct advantages in device integration density,operation speed,and power consumption.However,the fabrication processes of such 3D devices are complex,especially in the interconnection of electrodes.In this paper,we present a novel method which combines suspended electrodes and focused ion beam(FIB)technology to greatly simplify the electrodes interconnection in 3D devices.Based on this method,we fabricate 3D vertical core-double shell structure transistors with ZnO channel and Al_(2)O_(3) gate-oxide both grown by atomic layer deposition.Suspended top electrodes of vertical architecture could be directly connected to planar electrodes by FIB deposited Pt nanowires,which avoid cumbersome steps in the traditional 3D structure fabrication technology.Both single pillar and arrays devices show well behaved transfer characteristics with an Ion/Ioff current ratio greater than 106 and a low threshold voltage around 0 V.The ON-current of the 2×2 pillars vertical channel transistor was 1.2μA at the gate voltage of 3 V and drain voltage of 2 V,which can be also improved by increasing the number of pillars.Our method for fabricating vertical architecture transistors can be promising for device applications with high integration density and low power consumption.展开更多
The development of efficient catalysts for hydrogen evolution reaction(HER)and oxygen evolution reaction(OER)is of great significance for the practical application of water splitting in alkaline electrolytes.Transitio...The development of efficient catalysts for hydrogen evolution reaction(HER)and oxygen evolution reaction(OER)is of great significance for the practical application of water splitting in alkaline electrolytes.Transition metal sulfide electrocatalysts have been widely recognized as efficient catalysts for water splitting in alkaline media.In this work,an original and efficient synthesis strategy is proposed for the fabrication of asymmetric anode(N-(Co-Cu)S_(x))and cathode(N-CoS/Cu_(2)S).Impressively,these electrodes exhibit superior performance,benefiting from the construction of three-dimensional(3D)structures and the electronic structure adjustment caused by N-doping with increased active sites,improved mass/charge transport and enhanced evolution and release of gas bubbles.Hence,N-(Co-Cu)S_(x)anode exhibits excellent OER performance with only 217 mV overpotential at 10 mA·cm^(-2),while N-CoS/Cu_(2)S cathode possesses excellent HER performance with only 67 mV overpotential at 10 mA·cm^(-2).N-(Co-Cu)S_(x)||N-CoS/Cu_(2)S electrolyzer presents a low cell voltage of 1.53 V at 10 mA·cm^(-2)toward overall water splitting,which is superior to most recently reported transition metal sulfide-based catalysts.展开更多
Advanced oxidation processes are promising for degradation of the highly chemical stability and refractory methylisothiazolinone(MIT) bactericides in relevant industrial wastewater.In order to assemble a low cost and ...Advanced oxidation processes are promising for degradation of the highly chemical stability and refractory methylisothiazolinone(MIT) bactericides in relevant industrial wastewater.In order to assemble a low cost and high performance electrochemical oxidation system for wastewater treatment,granular active carbon(GAC) was decorated by doping Ce,Sn,Sb to synthesize Sn-Sb-Ce/GAC using sol-gel method as particle electrode filled into a three-dimensional(3D) electrochemical reactor.Scanning electron microscopy(SEM),energy-dispersive spectroscopy(EDS) and X-ray diffraction(XRD) experiments revealed that the Sn-Sb-Ce/GAC particle electrode crystal particles were compact and uniform,and the surface structure was improved.The ten cyclic experiments indicated that the Sn-Sb-Ce/GAC particle electrode had high stability and low dissolution of the loaded active substance.The degradation mechanism of MIT was studied under the optimal working conditions of 3D electrode system with GAC of 5 g/L,current density of 20 mA/cm^(2),initial pH 5,electrolyte concentration of Na_(2)SO_(4)0.02 mol/L and reaction time of 120 min.The indirect electrochemical degradation of MIT was dominated by active substance pathway that active chlorine rather than free radicals(·OH) played the main role.Comparing with conventional two-dimensional(2D) electrode system,the 3D electrochemical system has larger active electrode area,higher treatment efficiency and lower energy consumption than the former.The 3D electrochemical system could remove 96.5% of MIT from the actual high-salt reverse osmosis concentrate wastewater in 30 min.It has a certain removal effect on UV_(254)in wastewater,but has a better removal effect on fluorescent substances.This study proposed a new strategy to develop transition metal and rare earth metal particle electrodes using carbon-based materials for high efficient electrocatalytic oxidation in the electrochemical treatment system.展开更多
Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electroche...Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electrochemical measurements were used to characterize its morphology,crystal structure,and electrochemical properties.Removal of aniline by the Ti/TiOxHy/Sb-SnO2electrode was investigated by ultraviolet-Visible spectroscopy and chemical oxygen demand(COD)analysis under different conditions,including current densities,initial concentrations of aniline,pH values,concentrations of chloride ions,and types of reactor.It was found that a higher current density,a lower initial concentration of aniline,an acidic solution,the presence of chloride ions(0.2wt%NaCl),and a three-dimensional(3D)reactor promoted the removal efficiency of aniline.Electrochemical degradation of aniline followed pseudo-first-order kinetics.The aniline(200 mL of 100mg·L-(-1))and COD removal efficiencies reached 100%and 73.5%,respectively,at a current density of 20 mA·cm-(-2),pH of 7.0,and supporting electrolyte of 0.5 wt%Na2SO4 after 2 h electrolysis in a 3D reactor.These results show that aniline can be significantly removed on the Ti/TiOxHy/Sb-SnO2electrode,which provides an efficient way for elimination of aniline from aqueous solution.展开更多
A method using three-dimensional electrode is applied to treat wastewater in oil fields, which contains polyacrylamide （PAM）, for analogue. A best condition for electrolysis （I= 1.0 A, t=90 min, c=0.1%, m=980 g,φ=...A method using three-dimensional electrode is applied to treat wastewater in oil fields, which contains polyacrylamide （PAM）, for analogue. A best condition for electrolysis （I= 1.0 A, t=90 min, c=0.1%, m=980 g,φ=5 mm, d=5.0 cm） has been determined, under which the COD removal efficiency reached 96.0%, COD containing in wastewater reduced to 64.3 mg/L from 1 622.9 mg/L, the figure before treatment. Three categories of PAM-containing wastewater in production practice have been treated with the COD removal ratios being 87.5%, 82.4% and 84.7% respectively. Presence of H2O2 and ·OH are detected by means of Ti（IV）-5-Br-PADAP technique and colorimetry respectively. The concentration is positively proportional to the COD removal ratio and increases in accordance with increment of time of electrolysis and current.展开更多
The electrochemical treatment of COD contained in biologically pretreated coking wastewater treated by a three-dimensional electrode system with modified coke as the particle electrode was investigated. And the electr...The electrochemical treatment of COD contained in biologically pretreated coking wastewater treated by a three-dimensional electrode system with modified coke as the particle electrode was investigated. And the electrochemical perromance of the coke modified with various active components was studied. The results show that the coke modified with Fe（NO3）2 has the lowest energy consumption and higher COD removal rate under the same condition, and the modified coke has better surface characteristics for the purpose of this study. In addition, the kinetic constant was also calculated. The study shows that the three-dimensional electrode system with Fe （NO3）z-modified coke can give a satisfactory solution in biologically pretreated coking wastewater.展开更多
Transition metal oxide(TMO)nanoarrays are promising architecture designs for self-supporting oxygen electrodes to achieve high catalytic activities in lithium-oxygen(Li-O2)batteries.However,the poor conductive nature ...Transition metal oxide(TMO)nanoarrays are promising architecture designs for self-supporting oxygen electrodes to achieve high catalytic activities in lithium-oxygen(Li-O2)batteries.However,the poor conductive nature of TMOs and the confined growth of nanostructures on the limited surfaces of electrode substrates result in the low areal capacities of TMO nanoarray electrodes,which seriously deteriorates the intrinsically high energy densities of Li-O2 batteries.Herein,we propose a hybrid nanoarray architecture design that integrates the high electronic conductivity of carbon nanoflakes(CNFs)and the high catalytic activity of Co3 O4 nanosheets on carbon cloth(CC).Due to the synergistic effect of two differently featured components,the hybrid nanoarrays(Co3 O4-CNF@CC)achieve a high reversible capacity of3.14 mA h cm-2 that cannot be achieved by only single components.Further,CNFs grown on CC induce the three-dimensionally distributed growth of ultrafine Co3 O4 nanosheets to enable the efficient utilization of catalysts.Thus,with the high catalytic efficiency,hybrid Co3 O4-CNF@CC also achieves a more prolonged cycling life than pristine TMO nanoarrays.The present work provides a new strategy for improving the performance of nanoarray oxygen electrodes via the hybrid architecture design that integrates the intrinsic properties of each component and induces the three-dimensional distribution of catalysts.展开更多
High-concentration phenol wastewater is pollutant of concern that pose significant risks to human health and the environment.Three-dimensional electrocatalytic oxidation is one of the most promising wastewater treatme...High-concentration phenol wastewater is pollutant of concern that pose significant risks to human health and the environment.Three-dimensional electrocatalytic oxidation is one of the most promising wastewater treatment technologies because of its high treatment efficiency,low energy consumption and low secondary pollution.Lower-cost and higher-performance particles still faces great challenges.In this work,metal oxide particle electrodes were prepared using granular activated carbon(GAC)as a substrate to study the degradation of phenol by three-dimensional electrocatalytic oxidation.GAC particle electrodes loaded with different monometallic oxides(Mn,Fe,Co,Ce)and bimetallic oxides(Fe and Ce)were prepared by the impregnation method.The effectiveness of the particle electrodes in degrading phenol was greatly improved after active components loading.Among all monometallic oxide particle electrodes,the concentration degradation efficiency was in the order of Ce/GAC>Co/GAC>Mn/GAC>Fe/GAC,and the COD degradation efficiency was Ce/GAC>Fe/GAC>Co/GAC>Mn/GAC.After optimizing the loading metal type and loading amount,it was found that the 1.1%Fe-2.7%Ce/GAC particle electrode perform the best,with a phenol degradation efficiency of 95.48%,a COD degradation rate of 94.35%,an energy consumption of 0.75 kW·h·kg^(-1)COD.This lower-cost and higher-performance particle highlights a reliable route for solving the problem of particle electrode materials limiting the efficient treatment of phenol-containing wastewater.展开更多
In this work,we constructed a three-dimensional electrochemical system(3D-ECO),which included the cathode and anode electrode plates,as well as the screening of three-dimensional particle electrodes and parameter opti...In this work,we constructed a three-dimensional electrochemical system(3D-ECO),which included the cathode and anode electrode plates,as well as the screening of three-dimensional particle electrodes and parameter opti-mization,for the degradation of landfill leachate(LL)containing elevated levels of tetracycline(TC),and explored its mechanism of action.Firstly,titanium-based ruthenium-iridium(Ti/RuO_(2)-IrO_(2)),titanium-based ruthenium-iridium-platinum(Ti/Pt-RuO_(2)-IrO_(2)),and titanium-based tin-antimony(Ti/SnO_(2)-Sb_(2)O_(3))were employed as an-odes in the electrocatalytic oxidation system,with titanium and stainless steel plates serving as cathodes,to construct the optimal two-dimensional electrocatalytic oxidation system(2D-ECO)through cross-comparison ex-periments.Subsequently,using granular activated carbon(GAC),coconut shell biochar(CBC),walnut shell carbon(WBC),and bamboo charcoal(BBC)as particle electrodes,a 3D-ECO system was developed.The influence of var-ious operational parameters on treating TC-containing LL was investigated.The optimal operating parameters obtained from the study was:pH=5,current density of 30 mA/cm^(2),particle dosage of 7 g/L,particle size ranging from 1.70 to 2.00 mm,and electrode spacing of 4 cm.Under these conditions,the COD removal rate of 3D-ECO within three hours was 90.25%,the TC removal rate was 72.41%,and the NH_(3)-N removal rate was 39.52%.The removal of TC followed a pseudo-first-order kinetic model.Additionally,degradation mechanisms were elucidated through electron paramagnetic resonance(EPR)spectrometer and Tert-Butanol(TBA)quenching experiments,indicating that the degradation primarily occurred through a non-radical(1O_(2))pathway.This re-search offers a comprehensive analysis of the simultaneous breakdown of intricate LL matrices and TC,enhancing our comprehension of the degradation processes and underlying mechanisms.展开更多
N-doped activated carbon(AC)was employed in a three-dimensional electrode system(3DES)to enhance the removal of sulfur-containing volatile organic compounds(S-VOC).The technical parameters for preparing N-doped AC wer...N-doped activated carbon(AC)was employed in a three-dimensional electrode system(3DES)to enhance the removal of sulfur-containing volatile organic compounds(S-VOC).The technical parameters for preparing N-doped AC were optimized based on CS_(2)removal and COS accumulation,where the mass ratio of AC to urea was 1:1.0,and the activation temperature and heat-treatment time were 400℃and 120 min,respectively.When the mixing S-VOC were purified under an operating voltage of 8 V and peroxydisulfate concentration of 0.15 mol/L,CS_(2)removal in the 3DES system with N-doped AC reached 100%within 75 min,and was above 83%as purification time extended to 200 min.Additionally,the COS content in the outlet gas was usually undetectable within 120 min,and was lower than that in the other electrochemical systems.Modification of raw AC through urea impregnation and subsequent heat treatment significantly improved its surface structure and pore size distribution.Moreover,polar functional groups,such as C=O and pyridinic-N,increased noticeably,enhancing the SVOC adsorption capacity and dielectric properties.Consequently,highly reactive substances were more efficiently activated in 3DES system with N-doped AC,and oxidizing species HO·and^(1)O_(2)had important contributions to S-VOC purification compared to SO_(4)^(-)·radicals.A pathway was proposed to elucidate the transformation of sulfur-containing components,such as CH3SH and CS_(2).This study provides an efficient approach for S-VOC purification.展开更多
The development of an electrocatalyst based on abundant elements for the oxygen evolution reaction （OER） is important for water splitting associated with renewable energy sources. In this study, we develop an interc...The development of an electrocatalyst based on abundant elements for the oxygen evolution reaction （OER） is important for water splitting associated with renewable energy sources. In this study, we develop an interconnected Ni（Fe）OxHy nanosheet array on a stainless steel mesh （SSNNi） as an integrated OER electrode, without using any polymer binder. Benefiting from the well- defined three-dimensional （3D） architecture with highly exposed surface area, intimate contact between the active species and conductive substrate improved electron and mass transport capacity, facilitated electrolyte penetration, and improved mechanical stability. The SSNNi electrode also has excellent OER performance, including low overpotential, a small Tafel slope, and long-term durability in the alkaline electrolyte, making it one of the most promising OER electrodes developed.展开更多
The capacity of supercapacitor charge storage depends on the size of the electrode surface area and the active material on the electrodes.To enhance the charge storage capacity with a reduced volume,silicon is used as...The capacity of supercapacitor charge storage depends on the size of the electrode surface area and the active material on the electrodes.To enhance the charge storage capacity with a reduced volume,silicon is used as the electrode material,and three-dimensional electrode structure is prepared to increase the electrode surface area on the footprint area by inductively coupled plasma reactive etching(ICP) techniques.The anodic constant current deposition method is employed to deposit manganese oxide on the electrode surface as the electroactive material.For comparison,samples without slot are prepared with a two-dimensional electrode.Scanning Electron Microscopy(SEM) and Energy Dispersive Spectroscopy(EDS) are used to characterize the surface morphology of the electrode structure and the deposited electroactive material.Electrochemical properties of the electrode are characterized by the cyclic voltammetry(CV) and the constant current charge-discharge method.Experimental results show that our approach can effectively increase the electrode surface area with more electroactive substances,and hence can increase storage capacity of the micro-supercapacitor.展开更多
Solid oxide cells(SOCs),capable of interconverting electrical and chemical energy,have emerged as one of the key technologies for the future multi-energy complementary grid.However,the commercialization of SOCs is hin...Solid oxide cells(SOCs),capable of interconverting electrical and chemical energy,have emerged as one of the key technologies for the future multi-energy complementary grid.However,the commercialization of SOCs is hindered by poor long-term stability,attributed in large part to the microstructural evolution of the electrodes,which results in the loss of active reaction sites,blockage of gas transport pathways,and degradation of mechanical properties.Owing to recently developed three-dimensional(3D)microstructure reconstruction techniques,the microstructural evolution of SOC electrodes can now be investigated quantitatively.This review highlights insights gained from studies of the microstructural evolution of porous cermet SOC electrodes during long-term operation and redox cycling,and the corresponding effects on electrochemical and mechanical performance,with particular attention to investigations using 3D reconstruction technologies.The influencing parameters and the possible strategies to mitigate microstructure evolution-induced degradation are also summarized.The challenges and opportunities for the future development of stable and active SOC electrode microstructures are analyzed,and the corresponding prospects for commercial application are provided.展开更多
Aqueous Zinc-metal batteries(AZBs)hold great promise for energy storage applications,yet their practical deployment is hindered by challenges such as dendrite formation and parasitic side reactions at the Zn anode.Her...Aqueous Zinc-metal batteries(AZBs)hold great promise for energy storage applications,yet their practical deployment is hindered by challenges such as dendrite formation and parasitic side reactions at the Zn anode.Herein,we developed a three-dimensional Cu-coated flexible host via an electroless plating strategy on cotton cloth(Cu@CT).This design effectively homogenizes the local current density,spatially regulates Zn-ion flux,and accommodates substantial volume changes during cycling.Additionally,the zincophilic Cu coating facilitates Zn nucleation and deposition by forming Cu-Zn alloys,which reduce the Zn nucleation overpotential and promote uniform Zn plating.As a result,the Cu@CT based anode exhibits highly reversible Zn plating/stripping behavior with an average Coulombic efficiency of 99.58%over 800 cycles,accompanied by low polarization and dendrite-free behavior.Moreover,the Zn-I_(2) full cell demonstrates excellent rate capability,delivering a discharge capacity of 114 mA h g^(-1) at 10 A g^(-1),along with stable long-term cycling performance over 950 cycles.The electroless plating strategy may represent a promising pathway for advancing high-performance AZBs.展开更多
基金supported by Guangxi Science and Technology Major Program(No.AA23073008)Hubei Key Laboratory of Water System Science for Sponge City Construction(Wuhan University)(No.2023–05)Nanning Innovation and Entrepreneur Leading Talent Project(No.2021001).
文摘The three-dimensional particle electrode system exhibits significant potential for application in the treatment of wastewater.Nonetheless,the advancement of effective granular electrodes characterized by elevated catalytic activity and minimal energy consumption continues to pose a significant challenge.In this research,Fluorine-doped copper-carbon(F/Cu-GAC)particle electrodes were effectively synthesized through an impregnationcalcination technique,utilizing granular activated carbon as the carrier and fluorinedoped modified copper oxides as the catalytic agents.The particle electrodes were subsequently utilized to promote the degradation of 2,4,6-trichlorophenol(2,4,6-TCP)in a threedimensional electrocatalytic reactor(3DER).The F/Cu-GAC particle electrodes were polarized under the action of electric field,which promoted the heterogeneous Fenton-like reaction in which H2O2 generated by two-electron oxygen reduction reaction(2e-ORR)of O_(2) was catalytically decomposed to·OH.The 3DER equipped with F/Cu-GAC particle electrodes showed 100%removal of 2,4,6-TCP and 79.24%removal of TOC with a specific energy consumption(EC)of approximately 0.019 kWh/g·COD after 2 h of operation.The F/Cu-GAC particle electrodes exhibited an overpotential of 0.38 V and an electrochemically active surface area(ECSA)of 715 cm^(2),as determined through linear sweep voltammetry(LSV)and cyclic voltammetry(CV)assessments.These findings suggest a high level of electrocatalytic performance.Furthermore,the catalytic mechanism of the 3DER equipped with F/Cu-GAC particle electrodes was elucidated through the application of X-ray photoelectron spectroscopy(XPS),electron spin resonance(ESR),and active species capture experiments.This investigation offers a novel approach for the effective degradation of 2,4,6-TCP.
基金financially supported by the National Natural Science Foundation of China (No. 52004256)the Shanxi Provincial Science Foundation for Youths, China (No. 201901D211212)+2 种基金the Scientific and Technological Innovation Programs of Higher Education Institutions in Shanxi Province, China (No. 2019L0574)the Young Academic Leader of North University of China (No. QX202004)the Postdoctoral Innovative Talent Support Program of Hunan Province, China (2021RC2010)
文摘This study focused on As(V)removal by electrosorption in a self-made three-dimensional electrode reactor,in which granular activated carbon(GAC)was used as the particle electrode.Under the optimal conditions,the removal efficiency of As(V)was 84%,and its residual concentration in solution was 0.08 mg/L.From kinetic investigation,the rate determining steps of the entire process may involve more than two processes:membrane diffusion,material diffusion and physical/chemical adsorption processes.During the desorption process,As(V)can be desorbed from GAC,and the GAC was able to electro-adsorb As(V)again after desorption,which means that the electrode has good cycling performance.
基金Project(50925417)supported by the National Natureal Science Foundation for Distinguished Young Scholar of ChinaProject(51074191)supported by the National Natural Science Foundation of China
文摘The electrochemical degradation of reed pulp black liquor containing lignin pretreated by acidification method was investigated using a three-dimensional electrode reactor. Using activated carbon as particle electrode, the effects of p H value, reaction temperature, electrolysis time and current on residual concentration of total organic carbon(TOC) were discussed in detail. The optimal conditions were obtained: pH 2.5, influent flow rate of 200 mL/min, 25 °C, 300 mA and 2h of electrolysis time, and the removal efficiency of TOC maintains at 35.57 %. The results of the electrochemical method indicate that ·OH radicals are produced in activated carbon anode in the electrolysis process and then adsorbed on the activated carbon surface. Microcell consists of ·OH radicals and the absorbed lignin. With the microcell reaction, the lignin is degraded, while the anodic polarized curve illustrates that the lignin is obviously oxidized in the anode. The contributions of direct and indirect electrolyses to the TOC removal ratio are about 50%, respectively.
文摘The use of three-dimensional(3D)electrodes in water treatment is competitive because of their high catalytic efficiency,low energy consumption and promising development.The use of particle electrodes is a key research focus in this technology.They are usually in the form of particles that fill the space between the cathode and anode,and the selection of materials used is important.Carbon-based materials are widely used because of their large specific surface area,good adsorption performance,high chemical stability and low cost.The principles of 3D electrode technology are introduced and recent research on its use for degrading organic pollutants using carbon-based particle electrodes is summarized.The classification of particle electrodes is introduced and the challenges for the future development of carbon-based particle electrodes in wastewater treatment are discussed.
基金Supported by the National Natural Science Foundation of China(Nos.50602003, 50502004)the Beijing Science & Technology Star Plans, China(No.2007B020)
文摘Degradation of o-chloronitrobenzene wastewater was experimentally investigated at a three-dimensional electrode（TDE） with granular activated carbon as the particle electrode, graphite as the anode, and stainless steel plate as the cathode. The kinetic model of o-chloronitrobenzene degradation was studied, and the effects of pH, electrolysis time, particle electrode, electrolyte concentration, and initial concentration of the solution on degradation efficiency were investigated to determine the optimal operating conditions. The degradation of o-chloronitrobenzene by oxidation at the TDE was monitored by chemical oxygen demand（COD） measurements, UV-Vis absorption, and high performance liquid chromatography（HPLC）. COD degradation by electrochemical degradation followed pseudo-first order kinetics with respect to the concentration of o-chloronitrobenzene solutions. Optimal reaction conditions included 15 g of activated carbon as the particle electrode, 400 mg/L o-chloronitrobenzene solution containing 0.10 mol/L Na2SO4, pH=3, and 60 min of electrolysis. The UV-Vis absorption spectra and HPLC results illustrate that the benzene ring in o-chloronitrobenzene was rapidly broken down to form aliphatic substances through electrochemical degradation. COD degradation was approximately 98.5% at optimal conditions.
文摘In order to increase the electrode surface area and enhance the charge storage capacity, we study the micro electro mechanical system technology to fabricate three-dimensional high aspect ratio micro-electrode structure based on glass. The anodic constant potential method is employed to deposit manganese oxide as electroactive substances on the micro-electrode surface. Cyclic voltammetry and constant current charge-discharge method are both used to prepare electrode electrochemical performance testing, with a two-dimensional electrode without structure for comparison. Experimental results show that three-dimensional elec- trode structure can effectively enhance the charge storage capacity. At 1.0 mA/cm2 charge- discharge density, the three-dimensional electrode shows a capacitance of 17.88 mF/cm2, seven times higher than the two-dimensional electrode.
基金the National Key Research and Development Program of China(Grant Nos.2016YFA0200400 and 2016YFA0200800)the National Natural Science Foundation of China(Grant Nos.61888102,12074420,and 11674387)+1 种基金Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDB33000000)Key Research Program of Frontier Sciences,Chinese Acdemy of Sciences(Grant No.QYZDJ-SSWSLH042).
文摘Three-dimensional(3D)vertical architecture transistors represent an important technological pursuit,which have distinct advantages in device integration density,operation speed,and power consumption.However,the fabrication processes of such 3D devices are complex,especially in the interconnection of electrodes.In this paper,we present a novel method which combines suspended electrodes and focused ion beam(FIB)technology to greatly simplify the electrodes interconnection in 3D devices.Based on this method,we fabricate 3D vertical core-double shell structure transistors with ZnO channel and Al_(2)O_(3) gate-oxide both grown by atomic layer deposition.Suspended top electrodes of vertical architecture could be directly connected to planar electrodes by FIB deposited Pt nanowires,which avoid cumbersome steps in the traditional 3D structure fabrication technology.Both single pillar and arrays devices show well behaved transfer characteristics with an Ion/Ioff current ratio greater than 106 and a low threshold voltage around 0 V.The ON-current of the 2×2 pillars vertical channel transistor was 1.2μA at the gate voltage of 3 V and drain voltage of 2 V,which can be also improved by increasing the number of pillars.Our method for fabricating vertical architecture transistors can be promising for device applications with high integration density and low power consumption.
基金supported by the Science and Technology Project of Southwest Petroleum University(No.2021JBGS03)the Local Science and Technology Development Fund Projects Guided by the Central Government of China(No.2021ZYD0060)+2 种基金the National Natural Science Foundation of China(Nos.22209143 and 52371241)Guangdong High-level Innovation Institute Project(Nos.2021B0909050001 and 2021CX02L365)Guangdong Basic and Applied Basic Research Foundation(No.2023B1515120095).
文摘The development of efficient catalysts for hydrogen evolution reaction(HER)and oxygen evolution reaction(OER)is of great significance for the practical application of water splitting in alkaline electrolytes.Transition metal sulfide electrocatalysts have been widely recognized as efficient catalysts for water splitting in alkaline media.In this work,an original and efficient synthesis strategy is proposed for the fabrication of asymmetric anode(N-(Co-Cu)S_(x))and cathode(N-CoS/Cu_(2)S).Impressively,these electrodes exhibit superior performance,benefiting from the construction of three-dimensional(3D)structures and the electronic structure adjustment caused by N-doping with increased active sites,improved mass/charge transport and enhanced evolution and release of gas bubbles.Hence,N-(Co-Cu)S_(x)anode exhibits excellent OER performance with only 217 mV overpotential at 10 mA·cm^(-2),while N-CoS/Cu_(2)S cathode possesses excellent HER performance with only 67 mV overpotential at 10 mA·cm^(-2).N-(Co-Cu)S_(x)||N-CoS/Cu_(2)S electrolyzer presents a low cell voltage of 1.53 V at 10 mA·cm^(-2)toward overall water splitting,which is superior to most recently reported transition metal sulfide-based catalysts.
基金the financial supports from Major Science and Technology project of China Power Engineering Consulting Group Co., Ltd. "Research on Green and digital Intelligent Technology of Sewage Treatment Plant" (No. CEEC2023-ZDYF-09)Technology Innovation Ability Improvement Project of Shandong Province, China (No. 2022TSGC1247)。
文摘Advanced oxidation processes are promising for degradation of the highly chemical stability and refractory methylisothiazolinone(MIT) bactericides in relevant industrial wastewater.In order to assemble a low cost and high performance electrochemical oxidation system for wastewater treatment,granular active carbon(GAC) was decorated by doping Ce,Sn,Sb to synthesize Sn-Sb-Ce/GAC using sol-gel method as particle electrode filled into a three-dimensional(3D) electrochemical reactor.Scanning electron microscopy(SEM),energy-dispersive spectroscopy(EDS) and X-ray diffraction(XRD) experiments revealed that the Sn-Sb-Ce/GAC particle electrode crystal particles were compact and uniform,and the surface structure was improved.The ten cyclic experiments indicated that the Sn-Sb-Ce/GAC particle electrode had high stability and low dissolution of the loaded active substance.The degradation mechanism of MIT was studied under the optimal working conditions of 3D electrode system with GAC of 5 g/L,current density of 20 mA/cm^(2),initial pH 5,electrolyte concentration of Na_(2)SO_(4)0.02 mol/L and reaction time of 120 min.The indirect electrochemical degradation of MIT was dominated by active substance pathway that active chlorine rather than free radicals(·OH) played the main role.Comparing with conventional two-dimensional(2D) electrode system,the 3D electrochemical system has larger active electrode area,higher treatment efficiency and lower energy consumption than the former.The 3D electrochemical system could remove 96.5% of MIT from the actual high-salt reverse osmosis concentrate wastewater in 30 min.It has a certain removal effect on UV_(254)in wastewater,but has a better removal effect on fluorescent substances.This study proposed a new strategy to develop transition metal and rare earth metal particle electrodes using carbon-based materials for high efficient electrocatalytic oxidation in the electrochemical treatment system.
文摘Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electrochemical measurements were used to characterize its morphology,crystal structure,and electrochemical properties.Removal of aniline by the Ti/TiOxHy/Sb-SnO2electrode was investigated by ultraviolet-Visible spectroscopy and chemical oxygen demand(COD)analysis under different conditions,including current densities,initial concentrations of aniline,pH values,concentrations of chloride ions,and types of reactor.It was found that a higher current density,a lower initial concentration of aniline,an acidic solution,the presence of chloride ions(0.2wt%NaCl),and a three-dimensional(3D)reactor promoted the removal efficiency of aniline.Electrochemical degradation of aniline followed pseudo-first-order kinetics.The aniline(200 mL of 100mg·L-(-1))and COD removal efficiencies reached 100%and 73.5%,respectively,at a current density of 20 mA·cm-(-2),pH of 7.0,and supporting electrolyte of 0.5 wt%Na2SO4 after 2 h electrolysis in a 3D reactor.These results show that aniline can be significantly removed on the Ti/TiOxHy/Sb-SnO2electrode,which provides an efficient way for elimination of aniline from aqueous solution.
基金Supported by the National High-Technology Research and Development Program(2003AA602140-2)the Important Scientific Re-search Project of Hubei Provincial Department of Education, China (2004D001)
文摘A method using three-dimensional electrode is applied to treat wastewater in oil fields, which contains polyacrylamide （PAM）, for analogue. A best condition for electrolysis （I= 1.0 A, t=90 min, c=0.1%, m=980 g,φ=5 mm, d=5.0 cm） has been determined, under which the COD removal efficiency reached 96.0%, COD containing in wastewater reduced to 64.3 mg/L from 1 622.9 mg/L, the figure before treatment. Three categories of PAM-containing wastewater in production practice have been treated with the COD removal ratios being 87.5%, 82.4% and 84.7% respectively. Presence of H2O2 and ·OH are detected by means of Ti（IV）-5-Br-PADAP technique and colorimetry respectively. The concentration is positively proportional to the COD removal ratio and increases in accordance with increment of time of electrolysis and current.
文摘The electrochemical treatment of COD contained in biologically pretreated coking wastewater treated by a three-dimensional electrode system with modified coke as the particle electrode was investigated. And the electrochemical perromance of the coke modified with various active components was studied. The results show that the coke modified with Fe（NO3）2 has the lowest energy consumption and higher COD removal rate under the same condition, and the modified coke has better surface characteristics for the purpose of this study. In addition, the kinetic constant was also calculated. The study shows that the three-dimensional electrode system with Fe （NO3）z-modified coke can give a satisfactory solution in biologically pretreated coking wastewater.
基金supported by grants from the National Natural Science Foundation of China(Nos.21673169,51672205,51972257)the National Key Research Program of China(No.2016YFA0202602)+1 种基金the Research Start-Up Fund from Wuhan University of Technologythe Fundamental Research Funds for the Central Universities(WUT:No.2019IB003)。
文摘Transition metal oxide(TMO)nanoarrays are promising architecture designs for self-supporting oxygen electrodes to achieve high catalytic activities in lithium-oxygen(Li-O2)batteries.However,the poor conductive nature of TMOs and the confined growth of nanostructures on the limited surfaces of electrode substrates result in the low areal capacities of TMO nanoarray electrodes,which seriously deteriorates the intrinsically high energy densities of Li-O2 batteries.Herein,we propose a hybrid nanoarray architecture design that integrates the high electronic conductivity of carbon nanoflakes(CNFs)and the high catalytic activity of Co3 O4 nanosheets on carbon cloth(CC).Due to the synergistic effect of two differently featured components,the hybrid nanoarrays(Co3 O4-CNF@CC)achieve a high reversible capacity of3.14 mA h cm-2 that cannot be achieved by only single components.Further,CNFs grown on CC induce the three-dimensionally distributed growth of ultrafine Co3 O4 nanosheets to enable the efficient utilization of catalysts.Thus,with the high catalytic efficiency,hybrid Co3 O4-CNF@CC also achieves a more prolonged cycling life than pristine TMO nanoarrays.The present work provides a new strategy for improving the performance of nanoarray oxygen electrodes via the hybrid architecture design that integrates the intrinsic properties of each component and induces the three-dimensional distribution of catalysts.
文摘High-concentration phenol wastewater is pollutant of concern that pose significant risks to human health and the environment.Three-dimensional electrocatalytic oxidation is one of the most promising wastewater treatment technologies because of its high treatment efficiency,low energy consumption and low secondary pollution.Lower-cost and higher-performance particles still faces great challenges.In this work,metal oxide particle electrodes were prepared using granular activated carbon(GAC)as a substrate to study the degradation of phenol by three-dimensional electrocatalytic oxidation.GAC particle electrodes loaded with different monometallic oxides(Mn,Fe,Co,Ce)and bimetallic oxides(Fe and Ce)were prepared by the impregnation method.The effectiveness of the particle electrodes in degrading phenol was greatly improved after active components loading.Among all monometallic oxide particle electrodes,the concentration degradation efficiency was in the order of Ce/GAC>Co/GAC>Mn/GAC>Fe/GAC,and the COD degradation efficiency was Ce/GAC>Fe/GAC>Co/GAC>Mn/GAC.After optimizing the loading metal type and loading amount,it was found that the 1.1%Fe-2.7%Ce/GAC particle electrode perform the best,with a phenol degradation efficiency of 95.48%,a COD degradation rate of 94.35%,an energy consumption of 0.75 kW·h·kg^(-1)COD.This lower-cost and higher-performance particle highlights a reliable route for solving the problem of particle electrode materials limiting the efficient treatment of phenol-containing wastewater.
基金supported by the National Natural Science Foundation of China(Nos.42477406 and 51878617)the Horizontal Scientific Research Project(No.KYY-HX-20220803)the Engineering Research Center of Ministry of Education for Renewable Energy Infrastructure Construction Technology.
文摘In this work,we constructed a three-dimensional electrochemical system(3D-ECO),which included the cathode and anode electrode plates,as well as the screening of three-dimensional particle electrodes and parameter opti-mization,for the degradation of landfill leachate(LL)containing elevated levels of tetracycline(TC),and explored its mechanism of action.Firstly,titanium-based ruthenium-iridium(Ti/RuO_(2)-IrO_(2)),titanium-based ruthenium-iridium-platinum(Ti/Pt-RuO_(2)-IrO_(2)),and titanium-based tin-antimony(Ti/SnO_(2)-Sb_(2)O_(3))were employed as an-odes in the electrocatalytic oxidation system,with titanium and stainless steel plates serving as cathodes,to construct the optimal two-dimensional electrocatalytic oxidation system(2D-ECO)through cross-comparison ex-periments.Subsequently,using granular activated carbon(GAC),coconut shell biochar(CBC),walnut shell carbon(WBC),and bamboo charcoal(BBC)as particle electrodes,a 3D-ECO system was developed.The influence of var-ious operational parameters on treating TC-containing LL was investigated.The optimal operating parameters obtained from the study was:pH=5,current density of 30 mA/cm^(2),particle dosage of 7 g/L,particle size ranging from 1.70 to 2.00 mm,and electrode spacing of 4 cm.Under these conditions,the COD removal rate of 3D-ECO within three hours was 90.25%,the TC removal rate was 72.41%,and the NH_(3)-N removal rate was 39.52%.The removal of TC followed a pseudo-first-order kinetic model.Additionally,degradation mechanisms were elucidated through electron paramagnetic resonance(EPR)spectrometer and Tert-Butanol(TBA)quenching experiments,indicating that the degradation primarily occurred through a non-radical(1O_(2))pathway.This re-search offers a comprehensive analysis of the simultaneous breakdown of intricate LL matrices and TC,enhancing our comprehension of the degradation processes and underlying mechanisms.
基金financially supported by the the Reserve Talents of Young and Middle-aged Academic and Technical Leaders in Yunnan Province,China(No.202105AC160096).
文摘N-doped activated carbon(AC)was employed in a three-dimensional electrode system(3DES)to enhance the removal of sulfur-containing volatile organic compounds(S-VOC).The technical parameters for preparing N-doped AC were optimized based on CS_(2)removal and COS accumulation,where the mass ratio of AC to urea was 1:1.0,and the activation temperature and heat-treatment time were 400℃and 120 min,respectively.When the mixing S-VOC were purified under an operating voltage of 8 V and peroxydisulfate concentration of 0.15 mol/L,CS_(2)removal in the 3DES system with N-doped AC reached 100%within 75 min,and was above 83%as purification time extended to 200 min.Additionally,the COS content in the outlet gas was usually undetectable within 120 min,and was lower than that in the other electrochemical systems.Modification of raw AC through urea impregnation and subsequent heat treatment significantly improved its surface structure and pore size distribution.Moreover,polar functional groups,such as C=O and pyridinic-N,increased noticeably,enhancing the SVOC adsorption capacity and dielectric properties.Consequently,highly reactive substances were more efficiently activated in 3DES system with N-doped AC,and oxidizing species HO·and^(1)O_(2)had important contributions to S-VOC purification compared to SO_(4)^(-)·radicals.A pathway was proposed to elucidate the transformation of sulfur-containing components,such as CH3SH and CS_(2).This study provides an efficient approach for S-VOC purification.
基金This work is financially supported by the National Natural Science Foundation of China （Nos. 51472209, U1401241, 51522101, 51471075, 5163100, and 51401084）, and Specialized Research Fund for the Doctoral Program of Higher Education of China （No. 20110061120040）.
文摘The development of an electrocatalyst based on abundant elements for the oxygen evolution reaction （OER） is important for water splitting associated with renewable energy sources. In this study, we develop an interconnected Ni（Fe）OxHy nanosheet array on a stainless steel mesh （SSNNi） as an integrated OER electrode, without using any polymer binder. Benefiting from the well- defined three-dimensional （3D） architecture with highly exposed surface area, intimate contact between the active species and conductive substrate improved electron and mass transport capacity, facilitated electrolyte penetration, and improved mechanical stability. The SSNNi electrode also has excellent OER performance, including low overpotential, a small Tafel slope, and long-term durability in the alkaline electrolyte, making it one of the most promising OER electrodes developed.
文摘The capacity of supercapacitor charge storage depends on the size of the electrode surface area and the active material on the electrodes.To enhance the charge storage capacity with a reduced volume,silicon is used as the electrode material,and three-dimensional electrode structure is prepared to increase the electrode surface area on the footprint area by inductively coupled plasma reactive etching(ICP) techniques.The anodic constant current deposition method is employed to deposit manganese oxide on the electrode surface as the electroactive material.For comparison,samples without slot are prepared with a two-dimensional electrode.Scanning Electron Microscopy(SEM) and Energy Dispersive Spectroscopy(EDS) are used to characterize the surface morphology of the electrode structure and the deposited electroactive material.Electrochemical properties of the electrode are characterized by the cyclic voltammetry(CV) and the constant current charge-discharge method.Experimental results show that our approach can effectively increase the electrode surface area with more electroactive substances,and hence can increase storage capacity of the micro-supercapacitor.
基金funding from National Natural Science Foundation of China,China(52102226,12472173)Guangdong Basic and Applied Basic Research Foundation,China(2023A1515011003,2023A1515010723)+2 种基金Science,Technology and Innovation Commission of Shenzhen Municipality,China(GJHZ20220913143009017,GJHZ20210705141401004)the Talent Recruitment Project of Guangdong Province,China(2019QN01G098)Development and Reform Commission of Shenzhen Municipality,China(XMHT20220103004).
文摘Solid oxide cells(SOCs),capable of interconverting electrical and chemical energy,have emerged as one of the key technologies for the future multi-energy complementary grid.However,the commercialization of SOCs is hindered by poor long-term stability,attributed in large part to the microstructural evolution of the electrodes,which results in the loss of active reaction sites,blockage of gas transport pathways,and degradation of mechanical properties.Owing to recently developed three-dimensional(3D)microstructure reconstruction techniques,the microstructural evolution of SOC electrodes can now be investigated quantitatively.This review highlights insights gained from studies of the microstructural evolution of porous cermet SOC electrodes during long-term operation and redox cycling,and the corresponding effects on electrochemical and mechanical performance,with particular attention to investigations using 3D reconstruction technologies.The influencing parameters and the possible strategies to mitigate microstructure evolution-induced degradation are also summarized.The challenges and opportunities for the future development of stable and active SOC electrode microstructures are analyzed,and the corresponding prospects for commercial application are provided.
基金supported by the National Natural Science Foundation of China(52301285,52173091,and 22208331)Wuhan Science and Technology Bureau(2024040801020319)Department of Science and Technology of Hubei Province(2021CSA076).
文摘Aqueous Zinc-metal batteries(AZBs)hold great promise for energy storage applications,yet their practical deployment is hindered by challenges such as dendrite formation and parasitic side reactions at the Zn anode.Herein,we developed a three-dimensional Cu-coated flexible host via an electroless plating strategy on cotton cloth(Cu@CT).This design effectively homogenizes the local current density,spatially regulates Zn-ion flux,and accommodates substantial volume changes during cycling.Additionally,the zincophilic Cu coating facilitates Zn nucleation and deposition by forming Cu-Zn alloys,which reduce the Zn nucleation overpotential and promote uniform Zn plating.As a result,the Cu@CT based anode exhibits highly reversible Zn plating/stripping behavior with an average Coulombic efficiency of 99.58%over 800 cycles,accompanied by low polarization and dendrite-free behavior.Moreover,the Zn-I_(2) full cell demonstrates excellent rate capability,delivering a discharge capacity of 114 mA h g^(-1) at 10 A g^(-1),along with stable long-term cycling performance over 950 cycles.The electroless plating strategy may represent a promising pathway for advancing high-performance AZBs.
