From viewpoint of chemical element and microstructure of wood, this paper makes a discussion on thermal diffusivity of wood and two theoretical expressions of thermal diffusivity for the choral and radial directions w...From viewpoint of chemical element and microstructure of wood, this paper makes a discussion on thermal diffusivity of wood and two theoretical expressions of thermal diffusivity for the choral and radial directions were derived. The thermal diffusivities of the choral and radial directions for about 20 species of trees were calculated with the derived theoretical expressions and compared with the experimental values. The average error of the theoretical values of thermal diffusivity was 7.5% for choral direction and 6.2% for radial direction.展开更多
Thermal property is one of the most important properties of light-emitting diode （LED）. Thermal property of LED packaging material determines the heat dissipations of the phosphor and the chip surface, accordingly h...Thermal property is one of the most important properties of light-emitting diode （LED）. Thermal property of LED packaging material determines the heat dissipations of the phosphor and the chip surface, accordingly having an influence on the light-emitting efficiency and the life-span of the device. In this paper, photoacoustic piezoelectric （PAPE） technique has been employed to investigate the thermal properties of polyvinyl alcohol （]？VA） and silicon dioxide, which are the new and the traditional packaging materials in white LED, respectively. Firstly, the theory of PAPE technique has been developed for two-layer model in order to investigate soft materials; secondly, the experimental system has been set up and adjusted by measuring the reference sample; thirdly, the thermal diffusivities of PVA and silicon dioxide are measured and analysed. The experimental results show that PVA has a higher thermal diffusivity than silicon dioxide and is a better packaging material in the sense of thermal diffusivity for white LED.展开更多
The nanostructured zirconia coatings were deposited by atmospherically plasma spraying. Scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and X-ray diffraction were used to investigate the...The nanostructured zirconia coatings were deposited by atmospherically plasma spraying. Scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and X-ray diffraction were used to investigate the microstructure of the zirconia coatings. Thermal diffusivity values at normal temperatures have been evaluated by laser flash technique. Effect of annealing on the microstructure evolution of the zirconia coating has been performed. The grains and thermal diffusivity are increased with increasing annealing time and temperature. The grain growth is according to the GRIGC （the grain rotation induced grain coalescence） mechanism. The increase in thermal diffusivity is attributed to the grain growth and the decrease in porosity of nanostructured zirconia coatings.展开更多
Orthopyroxene is an important constitutive mineral in the crust and the upper mantle.Its thermal properties play a key role in constructing the thermal structure of the crust and the upper mantle.In this study,we deve...Orthopyroxene is an important constitutive mineral in the crust and the upper mantle.Its thermal properties play a key role in constructing the thermal structure of the crust and the upper mantle.In this study,we developed a new method to synthesize polycrystalline ferrosilite,one end-member of orthopyroxene,via the reaction of FeO+SiO_(2)→FeSiO_(3).We found that the P-T condition of 3 GPa and 1273 K is suitable to synthesize dense ferrosilite samples with low porosity.We employed the transient plane-source method to investigate the thermal conductivityκand thermal diffusivity D of synthetic ferrosilite at 1 GPa and 293-873 K,of which,κ=1.786+1.048×10^(3)T^(-1)-9.269×10^(4)T^(-2) and D=0.424+0.223×10^(3)T^(-1)+1.64×10^(4)T^(-2).Our results suggest phonon conduction should be the dominant mechanism at P-T conditions of interest since the thermal conductivity and the thermal diffusivity of ferrosilite both decrease with increasing temperature.The calculated heat capacity of ferrosilite at 1 GPa increases with temperature,which increases with increasing temperature with about 10%per 100 K(<500 K)and 4%per 100 K(>500 K).Iron content of an asteroid significantly influences its thermal evolution history and temperature distribution inside.It is expected that the mantle temperature of the Fe-rich asteroid will be higher and the Fe-rich asteroid's cooling history will be longer.展开更多
The paper explores the evolution of thermal behavior of the material by studying the variations in thermal diffusivity using the single beam thermal lens(TL) technique. For this purpose, the decomposition of Cu(OH)_(2...The paper explores the evolution of thermal behavior of the material by studying the variations in thermal diffusivity using the single beam thermal lens(TL) technique. For this purpose, the decomposition of Cu(OH)_(2) into CuO is studied in a time range up to 120 h, by subjecting the sample to morphological, structural, and spectroscopic characterizations. The time evolution of thermal diffusivity can be divided into three regions for demonstrating the dynamics of the reaction. When the reaction is complete, the thermal diffusivity is also found to be saturated. In addition to the morphological modifications,from rods to flakes, the variations in the amount of hydroxyl group are attributed to be responsible for the enhancement of base fluid's thermal diffusivity by 165%. Thus the study unveils the role of hydroxyl groups in the thermal behavior of CuO.展开更多
A very simple model based on the Quadrupole method was used in thetheoretical analysis of thermal diffusivity of composite materials of Cu-PVC, PVC-Cu-PVC, andCu-PVC-Cu. The use of MATLAB software with a return to rea...A very simple model based on the Quadrupole method was used in thetheoretical analysis of thermal diffusivity of composite materials of Cu-PVC, PVC-Cu-PVC, andCu-PVC-Cu. The use of MATLAB software with a return to real space using the Stehfest algorithm makesthe time of calculation very short. The thermal responses on the rear face of each consideredsample, which determine the thermal diffusivity were represented. A mathematical demonstration whichconfirmed the results was given. Thermal diffusivity determined from the rear face thermalresponses were compared with the results of the thermal diffusivity calculated by considering thecomposite materials to be homogeneous, and a discussion on the two kinds of results was provided.展开更多
This paper is concerned with the asymptotic behavior of solutions to the initial boundary problem of the two-dimensional density-dependent Boussinesq equations.It is shown that the solutions of the Boussinesq equation...This paper is concerned with the asymptotic behavior of solutions to the initial boundary problem of the two-dimensional density-dependent Boussinesq equations.It is shown that the solutions of the Boussinesq equations converge to those of zero thermal diffusivity Boussinesq equations as the thermal diffusivity tends to zero,and the convergence rate is established.In addition,we prove that the boundary-layer thickness is of the valueδ(k)=k^(α)with anyα∈(0,1/4)for a small diffusivity coefficient k>0,and we also find a function to describe the properties of the boundary layer.展开更多
A global mean ocean model including atmospheric heating, heat capacity of the mixed layer ocean, and vertical thermal diffusivity in the lower ocean, proposed by Cess and Goldenberg (1981), is used in this paper to st...A global mean ocean model including atmospheric heating, heat capacity of the mixed layer ocean, and vertical thermal diffusivity in the lower ocean, proposed by Cess and Goldenberg (1981), is used in this paper to study the sensitivity of global warming to the vertical diffusivity. The results suggest that the behaviour of upper ocean temperature is mainly determined by the magnitude of upper layer diffusivity and an ocean with a larger diffusivity leads to a less increase of sea surface temperature and a longer time delay for the global warming induced by increasing CO2 than that with smaller one. The global warming relative to four scenarios of CO2 emission assumed by Intergovernmental Panel of Climate Change (IPCC) is also estimated by using the model with two kinds of thermal diffusivities. The result shows that for various combinations of the CO2 emission scenarios and the diffusivities, the oceanic time delay to the global warming varies from 15 years to 70 years.展开更多
The heat equation is a second-order parabolic partial differential equation, which can be solved in many ways using numerical methods. This paper provides a numerical solution that uses the finite difference method li...The heat equation is a second-order parabolic partial differential equation, which can be solved in many ways using numerical methods. This paper provides a numerical solution that uses the finite difference method like the explicit center difference method. The forward time and centered space (FTCS) is used to a problem containing the one-dimensional heat equation and the stability condition of the scheme is reported with different thermal conductivity of different materials. In this study, results obtained for different thermal conductivity of distinct materials are compared. Also, the results reveal the well-behavior properties of the materials in good agreement.展开更多
Thermal diffusivity is a physical quantity that represents the thermal properties of soil.Amid the climate change known as global warming faced by humanity,Antarctica is one of the regions most affected by such change...Thermal diffusivity is a physical quantity that represents the thermal properties of soil.Amid the climate change known as global warming faced by humanity,Antarctica is one of the regions most affected by such changes.Therefore,in order to counter the effects of climate change,the thermal diffusivity of Antarctic regions is estimated in advance.展开更多
High energy consumption is a serious issue associated with in situ thermal desorption(TD)remediation of sites contaminated by petroleum hydrocarbons(PHs).The knowledge on the thermophysical properties of contaminated ...High energy consumption is a serious issue associated with in situ thermal desorption(TD)remediation of sites contaminated by petroleum hydrocarbons(PHs).The knowledge on the thermophysical properties of contaminated soil can help predict accurately the transient temperature distribution in a remediation site,for the purpose of energy conservation.However,such data are rarely reported for PH-contaminated soil.In this study,by taking diesel as a representative example for PHs,soil samples with constant dry bulk density but different diesel mass concentrations ranging from 0% to 20% were prepared,and the variations of their thermal conductivity,specific heat capacity and thermal diffusivity were measured and analyzed over a wide temperature range between 0℃ and 120℃.It was found that the effect of diesel concentration on the thermal conductivity of soil is negligible when it is below 1%.When diesel concentration is below 10%,the thermal conductivity of soil increases with raising the temperature.However,when diesel concentration becomes above 10%,the change of the thermal conductivity of soil with temperature exhibits the opposite trend.This is mainly due to the competition between soil minerals and diesel,because the thermal conductivity of minerals increases with temperature,whereas the thermal conductivity of diesel decreases with temperature.The analysis results showed that,compared with temperature,the diesel concentration has more significant effects on soil thermal conductivity.Regardless of the diesel concentration,with the increase of temperature,the specific heat capacity of soil increases,while the thermal diffusivity of soil decreases.In addition,the results of a control experiment exhibited that the relative differences of the thermal conductivity of the soil samples containing the same concentration of both diesel and a pure alkane are all below 10%,indicating that the results obtained with diesel in this study can be extended to the family of PHs.A theoretical prediction model was proposed based on cubic fractal and thermal resistance analysis,which confirmed that diesel concentration does have a significant effect on soil thermal conductivity.For the sake of practical applications,a regression model with the diesel concentration as a primary parameter was also proposed.展开更多
In this paper,we present a dual-wavelength flash Raman(DFR)mapping method for measuring the thermal diffusivity of a suspended nanowire.A heating pulse is used to heat the nanowire sample,and a probing pulse of differ...In this paper,we present a dual-wavelength flash Raman(DFR)mapping method for measuring the thermal diffusivity of a suspended nanowire.A heating pulse is used to heat the nanowire sample,and a probing pulse of different wavelength is used to measure the increase in temperature.The laser absorption coefficient can be eliminated by normalization,and the thermal diffusivity of the sample can be extracted from the normalized temperature increase.An infinite heat conduction model is used in this method to avoid the influence of boundary thermal resistance.By changing the position of the probing laser center,the measurement sensitivity of thermal diffusivity can be further improved.The position of maximum sensitivity is influenced by the thermal diffusivity of the nanowire,width of the heating pulse,radius of the heating laser spot,and characteristic length of the sample.To comprehensively analyze the influences of the various parameters,obtain the best measurement conditions,and attain maximum sensitivity,we propose a dimensionless physical model to analyze the heat conduction of the suspended nanowire.Based on the analysis of the best dimensionless parameters,the corresponding appropriate measurement conditions can be determined.Sensitivity analysis shows that when the radius of the heating laser spot is 1%of the length of the nanowire,the sensitivity of the DFR mapping method can be more than four times that of the concentric DFR method for measuring the thermal diffusivity of the nanowire.展开更多
Multi-material laser-based powder bed fusion (PBF-LB) allows manufacturing of parts with 3-dimensional gradient and additional functionality in a single step. This research focuses on the combination of thermally-cond...Multi-material laser-based powder bed fusion (PBF-LB) allows manufacturing of parts with 3-dimensional gradient and additional functionality in a single step. This research focuses on the combination of thermally-conductive CuCr1Zr with hard M300 tool steel.Two interface configurations of M300 on CuCr1Zr and CuCr1Zr on M300 were investigated. Ultra-fine grains form at the interface due to the low mutual solubility of Cu and steel. The material mixing zone size is dependent on the configurations and tunable in the range of0.1–0.3 mm by introducing a separate set of parameters for the interface layers. Microcracks and pores mainly occur in the transition zone.Regardless of these defects, the thermal diffusivity of bimetallic parts with 50vol% of CuCr1Zr significantly increases by 70%–150%compared to pure M300. The thermal diffusivity of CuCr1Zr and the hardness of M300 steel can be enhanced simultaneously by applying the aging heat treatment.展开更多
Rock thermal physical properties play a crucial role in understanding deep thermal conditions,modeling the thermal structure of the lithosphere,and discovering the evolutionary history of sedimentary basins.Recent adv...Rock thermal physical properties play a crucial role in understanding deep thermal conditions,modeling the thermal structure of the lithosphere,and discovering the evolutionary history of sedimentary basins.Recent advancements in geothermal exploration,particularly the identification of high-temperature geothermal resources in Datong Basin,Shanxi,China,have opened new possibilities.This study aims to characterize the thermal properties of rocks and explore factors influencing thermal conductivity in basins hosting high-temperature geothermal resources.A total of 70 groups of rock samples were collected from outcrops in and around Datong Basin,Shanxi Province.Thermal property tests were carried out to analyze the rock properties,and the influencing factors of thermal conductivity were studied through experiments at different temperature and water-filled states.The results indicate that the thermal conductivity of rocks in Datong,Shanxi Province,typically ranges from 0.690 W/(m·K)to 6.460 W/(m·K),the thermal diffusion coefficient ranges from 0.441 mm^(2)/s to 2.023 mm^(2)/s,and the specific heat capacity of the rocks ranges from 0.569 KJ/(kg·℃)to 1.117 KJ/(kg·°C).Experimental results reveal the impact of temperature and water saturation on the thermal conductivity of the rock.The thermal conductivity decreases with increasing temperature and rises with high water saturation.A temperature correction formula for the thermal conductivity of different lithologies in the area is proposed through linear fitting.The findings from this study provide essential parameters for the assessment and prediction,development,and utilization of geothermal resources in the region and other basins with typical high-temperature geothermal resource.展开更多
A method of measuring thermal diffusivity of materials at room temperature by photothermal reflection technique is described. An intensity-modulated Ar+ laser beam is used as incident light. The beam is focused to abo...A method of measuring thermal diffusivity of materials at room temperature by photothermal reflection technique is described. An intensity-modulated Ar+ laser beam is used as incident light. The beam is focused to about 1 mm diameter spot and illuminates the sample surface. HgCdTe infrared detector is used to receive photothermal signal. By using this technique, the photothermal signals are experimentally measured as the function of different frequencies. The thermal diffusivities can be obtained by fitting the experimental data. On the other hand, the thermal diffusivities of one-way composite and orthogonal symmetric arranged composites Al2O3/Al are measured in transverse, longitudinal and arbitrary directions. The results show that the diffusivity of one-way material decreases with the increase of the measurement angle; the diffusivity of orthogonally arranged material almost keeps the same when measurement angle changes.展开更多
A novel approach based on thermal diffusion was used to achieve controllable Mg content in A_(2)B_(7)-type La-Mg-Ni-based alloys.The formation mechanism of the A_(2)B_(7)-type phase as a result of the thermal diffusio...A novel approach based on thermal diffusion was used to achieve controllable Mg content in A_(2)B_(7)-type La-Mg-Ni-based alloys.The formation mechanism of the A_(2)B_(7)-type phase as a result of the thermal diffusion process and the effect of Mg content on hydrogen storage performance were investigated.X-ray diffraction(XRD)patterns and Rietveld refinement results showed that increased Mg transformed the LaNi_(5)phase in the La_(0.74)Sm_(0.03)Y_(0.23)Ni_(4.32)Al_(0.04)precursor alloy into a superlattice structure.Scanning electron microscopy(SEM)images showed that Mg was evenly distributed in the alloy bulk.Mg in the superlattice significantly inhibited the phase decomposition of the superlattice structure during the hydrogen absorption/desorption cycles.An A_(2)B_(7)-type La_(0.57)Sm_(0.02)Y_(0.18)Mg_(0.23)Ni_(3.38)Al_(0.03)alloy composed of Gd_(2)Co_(7)and Ce_(2)Ni_(7)phases was successfully synthesized.The pressure-composition isotherm profiles showed that the alloy had a hydrogen storage capacity as high as 1.73 wt%,with good cycling stability.After 50 cycles of hydrogen absorption/desorption,the alloy retained a hydrogen storage capacity of 1.45 wt%,with a capacity retention rate of up to 84.28%.The Mg thermal diffusion process thus provides a new approach for the controlled preparation of La-Mg-Ni-based alloys.展开更多
We attempt to compute the Surface Average Heat Flow （SAHF） from long-term temperature observations of one hundred seventy-seven observational points at the depths of 0.8, 1.6, and 3.2 m, which were relatively evenly...We attempt to compute the Surface Average Heat Flow （SAHF） from long-term temperature observations of one hundred seventy-seven observational points at the depths of 0.8, 1.6, and 3.2 m, which were relatively evenly distributed in China's Mainland. We first employ Fourier transformation to remove the influence of atmospheric temperature variations from the observation series, which are classified into the type of the steady-state temperature monotonously increasing with depth （type I） and other three types. Then we compare our results obtained from the data of type I, of which the values are thought to equal to those of the mean borehole heat flow, with those obtained from traditional heat flow observations mainly distributed in North China Craton. In computations of the SAHF at the observation stations, we deduce the thermal diffusivity and volumetric specific heat of the soil by employing harmonic solutions of the heat conduction equation for the same moisture group as the first step, and then we determine the SAHF using Fourier＇s law. Our results indicate that the SAHF derived from shallow earth geothermal data can reflect the heat flow field to a large extent.展开更多
Data from July 2006 to June 2008 observed at SACOL （Semi-Arid Climate and Environment Observatory of Lanzhou University, 35.946°N, 104.137°E, elev. 1961 m）, a semi-arid site in Northwest China, are used to...Data from July 2006 to June 2008 observed at SACOL （Semi-Arid Climate and Environment Observatory of Lanzhou University, 35.946°N, 104.137°E, elev. 1961 m）, a semi-arid site in Northwest China, are used to study seasonal variability of soil moisture, along with surface albedo and other soil thermal parameters, such as heat capacity, thermal conductivity and thermal diffusivity, and their relationships to soil moisture content. The results indicate that surface albedo decreases with increases in soil moisture content, showing a typical exponential relation between the surface albedo and the soil moisture. The heat capacity, the soil thermal diffusivity, and soil thermal conductivity show large variations between Julian day 90-212 and 450-578. The soil thermal conductivity is found to increase as a power function of soil moisture. Soil heat capacity and soil thermal diffusivity increase with increases in soil moisture. The SACOL observed soil moisture are also used to validate the AMSR-E/AQUA retrieved soil moisture and there is good agreement between them. The analysis of the relationship between satellite retrieved soil moisture and precipitation suggests that the variability of soil moisture depends on the variation of precipitation over the Loess Plateau.展开更多
Continuous observation data collected over the whole year of 2004 on a cropland surtace m Tongyu, a senti-arid area of northeastern China （44°25＇N, 122°52＇E）, have been used to investigate the variations...Continuous observation data collected over the whole year of 2004 on a cropland surtace m Tongyu, a senti-arid area of northeastern China （44°25＇N, 122°52＇E）, have been used to investigate the variations of surface albedo and soil thermal parameters, including heat capacity, thermal conductivity and thermal diffusivity, and their relationships to soil moisture. The diurnal variation of surface albedo appears as a U shape curve on sunny days. Surface albedo decreases with the increase of solar elevation angle, and it tends to be a constant when solar elevation angle is larger than 40°. So the daily average surface albedo was computed using the data when solar elevation angle is larger than 40° Mean daily surface albedo is found to decrease with the increase of soil moisture, showing an exponential dependence on soil moisture. The variations of soil heat capacity are small during Julian days 90 300. Compared with the heat capacity, soil thermal conductivity has very gentle variations during this period, but the soil thermal diffusivity has wide variations during the same period. The soil thermal conductivity is found to increase as a power function of soil moisture. The soil thermal diffusivity increases firstly and then decreases with the increase of soil moisture.展开更多
The thermal conductivity or diffusivity of pearlitic grey irons with various carbon contents is investigated by the laser flash method. The materials are cast in controlled thermal environments and produced in three d...The thermal conductivity or diffusivity of pearlitic grey irons with various carbon contents is investigated by the laser flash method. The materials are cast in controlled thermal environments and produced in three dissimilar cooling rates. The cooling rate together with the carbon content largely influence the thermal conductivity of grey iron. Linear relationships exist between the thermal conductivity and the carbon content,the carbon equivalent and the fraction of former primary solidified austenite transformed into pearlite. The work shows that optimal thermal transport properties are obtained at medium cooling rates. Equations describing the thermal conductivity of pearlite,solidified as pre-eutectic austenite,and the eutectic of grey iron are derived. The thermal conductivity of pearlitic grey iron is modeled at both room temperature and elevated temperature with good accuracy.展开更多
基金Natural Science Foundation of Fujian Province. "Theoretical Research on Wood Thermal Property".
文摘From viewpoint of chemical element and microstructure of wood, this paper makes a discussion on thermal diffusivity of wood and two theoretical expressions of thermal diffusivity for the choral and radial directions were derived. The thermal diffusivities of the choral and radial directions for about 20 species of trees were calculated with the derived theoretical expressions and compared with the experimental values. The average error of the theoretical values of thermal diffusivity was 7.5% for choral direction and 6.2% for radial direction.
基金Project supported by the National Nature Science Foundation of China (Grant No. 50506006)the National High Technology Research and Development Program of China (Grant No. 2006AA03A116)the Youth Foundation of University of Electronic Science and Technology of China (Grant No. JX05024)
文摘Thermal property is one of the most important properties of light-emitting diode （LED）. Thermal property of LED packaging material determines the heat dissipations of the phosphor and the chip surface, accordingly having an influence on the light-emitting efficiency and the life-span of the device. In this paper, photoacoustic piezoelectric （PAPE） technique has been employed to investigate the thermal properties of polyvinyl alcohol （]？VA） and silicon dioxide, which are the new and the traditional packaging materials in white LED, respectively. Firstly, the theory of PAPE technique has been developed for two-layer model in order to investigate soft materials; secondly, the experimental system has been set up and adjusted by measuring the reference sample; thirdly, the thermal diffusivities of PVA and silicon dioxide are measured and analysed. The experimental results show that PVA has a higher thermal diffusivity than silicon dioxide and is a better packaging material in the sense of thermal diffusivity for white LED.
基金This work was supported by the program for New Century Excellent Talents in University(NCET)the National Natural Science Foundation of China under the contact 50176005.
文摘The nanostructured zirconia coatings were deposited by atmospherically plasma spraying. Scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and X-ray diffraction were used to investigate the microstructure of the zirconia coatings. Thermal diffusivity values at normal temperatures have been evaluated by laser flash technique. Effect of annealing on the microstructure evolution of the zirconia coating has been performed. The grains and thermal diffusivity are increased with increasing annealing time and temperature. The grain growth is according to the GRIGC （the grain rotation induced grain coalescence） mechanism. The increase in thermal diffusivity is attributed to the grain growth and the decrease in porosity of nanostructured zirconia coatings.
基金supported by the CAS“Light of West China”Program(No.Y9CR026)the National Natural Science Foundation of China(No.442072051)。
文摘Orthopyroxene is an important constitutive mineral in the crust and the upper mantle.Its thermal properties play a key role in constructing the thermal structure of the crust and the upper mantle.In this study,we developed a new method to synthesize polycrystalline ferrosilite,one end-member of orthopyroxene,via the reaction of FeO+SiO_(2)→FeSiO_(3).We found that the P-T condition of 3 GPa and 1273 K is suitable to synthesize dense ferrosilite samples with low porosity.We employed the transient plane-source method to investigate the thermal conductivityκand thermal diffusivity D of synthetic ferrosilite at 1 GPa and 293-873 K,of which,κ=1.786+1.048×10^(3)T^(-1)-9.269×10^(4)T^(-2) and D=0.424+0.223×10^(3)T^(-1)+1.64×10^(4)T^(-2).Our results suggest phonon conduction should be the dominant mechanism at P-T conditions of interest since the thermal conductivity and the thermal diffusivity of ferrosilite both decrease with increasing temperature.The calculated heat capacity of ferrosilite at 1 GPa increases with temperature,which increases with increasing temperature with about 10%per 100 K(<500 K)and 4%per 100 K(>500 K).Iron content of an asteroid significantly influences its thermal evolution history and temperature distribution inside.It is expected that the mantle temperature of the Fe-rich asteroid will be higher and the Fe-rich asteroid's cooling history will be longer.
文摘The paper explores the evolution of thermal behavior of the material by studying the variations in thermal diffusivity using the single beam thermal lens(TL) technique. For this purpose, the decomposition of Cu(OH)_(2) into CuO is studied in a time range up to 120 h, by subjecting the sample to morphological, structural, and spectroscopic characterizations. The time evolution of thermal diffusivity can be divided into three regions for demonstrating the dynamics of the reaction. When the reaction is complete, the thermal diffusivity is also found to be saturated. In addition to the morphological modifications,from rods to flakes, the variations in the amount of hydroxyl group are attributed to be responsible for the enhancement of base fluid's thermal diffusivity by 165%. Thus the study unveils the role of hydroxyl groups in the thermal behavior of CuO.
基金The research work is financially supported by National Natural Science Foundation of China (No.50276003).
文摘A very simple model based on the Quadrupole method was used in thetheoretical analysis of thermal diffusivity of composite materials of Cu-PVC, PVC-Cu-PVC, andCu-PVC-Cu. The use of MATLAB software with a return to real space using the Stehfest algorithm makesthe time of calculation very short. The thermal responses on the rear face of each consideredsample, which determine the thermal diffusivity were represented. A mathematical demonstration whichconfirmed the results was given. Thermal diffusivity determined from the rear face thermalresponses were compared with the results of the thermal diffusivity calculated by considering thecomposite materials to be homogeneous, and a discussion on the two kinds of results was provided.
基金the National Natural Science Foundation of China(12061037,11971209)the Natural Science Foundation of Jiangxi Province(20212BAB201016)National Natural Science Foundation of China(11861038)。
文摘This paper is concerned with the asymptotic behavior of solutions to the initial boundary problem of the two-dimensional density-dependent Boussinesq equations.It is shown that the solutions of the Boussinesq equations converge to those of zero thermal diffusivity Boussinesq equations as the thermal diffusivity tends to zero,and the convergence rate is established.In addition,we prove that the boundary-layer thickness is of the valueδ(k)=k^(α)with anyα∈(0,1/4)for a small diffusivity coefficient k>0,and we also find a function to describe the properties of the boundary layer.
文摘A global mean ocean model including atmospheric heating, heat capacity of the mixed layer ocean, and vertical thermal diffusivity in the lower ocean, proposed by Cess and Goldenberg (1981), is used in this paper to study the sensitivity of global warming to the vertical diffusivity. The results suggest that the behaviour of upper ocean temperature is mainly determined by the magnitude of upper layer diffusivity and an ocean with a larger diffusivity leads to a less increase of sea surface temperature and a longer time delay for the global warming induced by increasing CO2 than that with smaller one. The global warming relative to four scenarios of CO2 emission assumed by Intergovernmental Panel of Climate Change (IPCC) is also estimated by using the model with two kinds of thermal diffusivities. The result shows that for various combinations of the CO2 emission scenarios and the diffusivities, the oceanic time delay to the global warming varies from 15 years to 70 years.
文摘The heat equation is a second-order parabolic partial differential equation, which can be solved in many ways using numerical methods. This paper provides a numerical solution that uses the finite difference method like the explicit center difference method. The forward time and centered space (FTCS) is used to a problem containing the one-dimensional heat equation and the stability condition of the scheme is reported with different thermal conductivity of different materials. In this study, results obtained for different thermal conductivity of distinct materials are compared. Also, the results reveal the well-behavior properties of the materials in good agreement.
基金financially supported by the Korea Polar Research Institute(KOPRI)Project(PE19200)Basic Science Research Program through the National Research Foundation of Korea(NRF)funded by the Ministry of Education(No.2019R1A6A1A03033167).
文摘Thermal diffusivity is a physical quantity that represents the thermal properties of soil.Amid the climate change known as global warming faced by humanity,Antarctica is one of the regions most affected by such changes.Therefore,in order to counter the effects of climate change,the thermal diffusivity of Antarctic regions is estimated in advance.
基金financially supported by the National Key Research and Development Program (project No.2019YFC1805700,program No.2019YFC1805701)。
文摘High energy consumption is a serious issue associated with in situ thermal desorption(TD)remediation of sites contaminated by petroleum hydrocarbons(PHs).The knowledge on the thermophysical properties of contaminated soil can help predict accurately the transient temperature distribution in a remediation site,for the purpose of energy conservation.However,such data are rarely reported for PH-contaminated soil.In this study,by taking diesel as a representative example for PHs,soil samples with constant dry bulk density but different diesel mass concentrations ranging from 0% to 20% were prepared,and the variations of their thermal conductivity,specific heat capacity and thermal diffusivity were measured and analyzed over a wide temperature range between 0℃ and 120℃.It was found that the effect of diesel concentration on the thermal conductivity of soil is negligible when it is below 1%.When diesel concentration is below 10%,the thermal conductivity of soil increases with raising the temperature.However,when diesel concentration becomes above 10%,the change of the thermal conductivity of soil with temperature exhibits the opposite trend.This is mainly due to the competition between soil minerals and diesel,because the thermal conductivity of minerals increases with temperature,whereas the thermal conductivity of diesel decreases with temperature.The analysis results showed that,compared with temperature,the diesel concentration has more significant effects on soil thermal conductivity.Regardless of the diesel concentration,with the increase of temperature,the specific heat capacity of soil increases,while the thermal diffusivity of soil decreases.In addition,the results of a control experiment exhibited that the relative differences of the thermal conductivity of the soil samples containing the same concentration of both diesel and a pure alkane are all below 10%,indicating that the results obtained with diesel in this study can be extended to the family of PHs.A theoretical prediction model was proposed based on cubic fractal and thermal resistance analysis,which confirmed that diesel concentration does have a significant effect on soil thermal conductivity.For the sake of practical applications,a regression model with the diesel concentration as a primary parameter was also proposed.
基金supported by the National Natural Science Foundation of China(Grant Nos.51827807 and 51636002).
文摘In this paper,we present a dual-wavelength flash Raman(DFR)mapping method for measuring the thermal diffusivity of a suspended nanowire.A heating pulse is used to heat the nanowire sample,and a probing pulse of different wavelength is used to measure the increase in temperature.The laser absorption coefficient can be eliminated by normalization,and the thermal diffusivity of the sample can be extracted from the normalized temperature increase.An infinite heat conduction model is used in this method to avoid the influence of boundary thermal resistance.By changing the position of the probing laser center,the measurement sensitivity of thermal diffusivity can be further improved.The position of maximum sensitivity is influenced by the thermal diffusivity of the nanowire,width of the heating pulse,radius of the heating laser spot,and characteristic length of the sample.To comprehensively analyze the influences of the various parameters,obtain the best measurement conditions,and attain maximum sensitivity,we propose a dimensionless physical model to analyze the heat conduction of the suspended nanowire.Based on the analysis of the best dimensionless parameters,the corresponding appropriate measurement conditions can be determined.Sensitivity analysis shows that when the radius of the heating laser spot is 1%of the length of the nanowire,the sensitivity of the DFR mapping method can be more than four times that of the concentric DFR method for measuring the thermal diffusivity of the nanowire.
基金supported by VTT Technical Research Centre of Finland,Aalto University,Aerosint SA,and partially from European Union Horizon 2020 (No.768775)。
文摘Multi-material laser-based powder bed fusion (PBF-LB) allows manufacturing of parts with 3-dimensional gradient and additional functionality in a single step. This research focuses on the combination of thermally-conductive CuCr1Zr with hard M300 tool steel.Two interface configurations of M300 on CuCr1Zr and CuCr1Zr on M300 were investigated. Ultra-fine grains form at the interface due to the low mutual solubility of Cu and steel. The material mixing zone size is dependent on the configurations and tunable in the range of0.1–0.3 mm by introducing a separate set of parameters for the interface layers. Microcracks and pores mainly occur in the transition zone.Regardless of these defects, the thermal diffusivity of bimetallic parts with 50vol% of CuCr1Zr significantly increases by 70%–150%compared to pure M300. The thermal diffusivity of CuCr1Zr and the hardness of M300 steel can be enhanced simultaneously by applying the aging heat treatment.
基金supported by the Geothermal Survey Project of the China Geological Survey(Grant No.DD20221676)the Shanxi Geoscience Think Tank Development Fund 2023–001 and Basic Research Operations Project of the Institute of Hydrogeology and Environmental Geology,Chinese Academy of Geological Sciences(SK202212).
文摘Rock thermal physical properties play a crucial role in understanding deep thermal conditions,modeling the thermal structure of the lithosphere,and discovering the evolutionary history of sedimentary basins.Recent advancements in geothermal exploration,particularly the identification of high-temperature geothermal resources in Datong Basin,Shanxi,China,have opened new possibilities.This study aims to characterize the thermal properties of rocks and explore factors influencing thermal conductivity in basins hosting high-temperature geothermal resources.A total of 70 groups of rock samples were collected from outcrops in and around Datong Basin,Shanxi Province.Thermal property tests were carried out to analyze the rock properties,and the influencing factors of thermal conductivity were studied through experiments at different temperature and water-filled states.The results indicate that the thermal conductivity of rocks in Datong,Shanxi Province,typically ranges from 0.690 W/(m·K)to 6.460 W/(m·K),the thermal diffusion coefficient ranges from 0.441 mm^(2)/s to 2.023 mm^(2)/s,and the specific heat capacity of the rocks ranges from 0.569 KJ/(kg·℃)to 1.117 KJ/(kg·°C).Experimental results reveal the impact of temperature and water saturation on the thermal conductivity of the rock.The thermal conductivity decreases with increasing temperature and rises with high water saturation.A temperature correction formula for the thermal conductivity of different lithologies in the area is proposed through linear fitting.The findings from this study provide essential parameters for the assessment and prediction,development,and utilization of geothermal resources in the region and other basins with typical high-temperature geothermal resource.
基金This project was supported by Shandong National Science Foundation under Grant No. Y2002A08.
文摘A method of measuring thermal diffusivity of materials at room temperature by photothermal reflection technique is described. An intensity-modulated Ar+ laser beam is used as incident light. The beam is focused to about 1 mm diameter spot and illuminates the sample surface. HgCdTe infrared detector is used to receive photothermal signal. By using this technique, the photothermal signals are experimentally measured as the function of different frequencies. The thermal diffusivities can be obtained by fitting the experimental data. On the other hand, the thermal diffusivities of one-way composite and orthogonal symmetric arranged composites Al2O3/Al are measured in transverse, longitudinal and arbitrary directions. The results show that the diffusivity of one-way material decreases with the increase of the measurement angle; the diffusivity of orthogonally arranged material almost keeps the same when measurement angle changes.
基金financially supported by the National Key Research and Development Program of China(2022YFB3803804)the National Natural Science Foundation of China(Nos.51971197,52071281 and 52201282)+3 种基金Basic Innovation Research Project in Yanshan University(No.2022LGZD004)China Postdoctoral Science Foundation(2023M742945)Postdoctoral research project of Hebei Province(B2023003023)Subsidy for Hebei Key Laboratory of Applied Chemistry after Operation Performance(No.22567616H)。
文摘A novel approach based on thermal diffusion was used to achieve controllable Mg content in A_(2)B_(7)-type La-Mg-Ni-based alloys.The formation mechanism of the A_(2)B_(7)-type phase as a result of the thermal diffusion process and the effect of Mg content on hydrogen storage performance were investigated.X-ray diffraction(XRD)patterns and Rietveld refinement results showed that increased Mg transformed the LaNi_(5)phase in the La_(0.74)Sm_(0.03)Y_(0.23)Ni_(4.32)Al_(0.04)precursor alloy into a superlattice structure.Scanning electron microscopy(SEM)images showed that Mg was evenly distributed in the alloy bulk.Mg in the superlattice significantly inhibited the phase decomposition of the superlattice structure during the hydrogen absorption/desorption cycles.An A_(2)B_(7)-type La_(0.57)Sm_(0.02)Y_(0.18)Mg_(0.23)Ni_(3.38)Al_(0.03)alloy composed of Gd_(2)Co_(7)and Ce_(2)Ni_(7)phases was successfully synthesized.The pressure-composition isotherm profiles showed that the alloy had a hydrogen storage capacity as high as 1.73 wt%,with good cycling stability.After 50 cycles of hydrogen absorption/desorption,the alloy retained a hydrogen storage capacity of 1.45 wt%,with a capacity retention rate of up to 84.28%.The Mg thermal diffusion process thus provides a new approach for the controlled preparation of La-Mg-Ni-based alloys.
基金supported by the National Natural Science Foundation of China(Grant No.4087404741174084)
文摘We attempt to compute the Surface Average Heat Flow （SAHF） from long-term temperature observations of one hundred seventy-seven observational points at the depths of 0.8, 1.6, and 3.2 m, which were relatively evenly distributed in China's Mainland. We first employ Fourier transformation to remove the influence of atmospheric temperature variations from the observation series, which are classified into the type of the steady-state temperature monotonously increasing with depth （type I） and other three types. Then we compare our results obtained from the data of type I, of which the values are thought to equal to those of the mean borehole heat flow, with those obtained from traditional heat flow observations mainly distributed in North China Craton. In computations of the SAHF at the observation stations, we deduce the thermal diffusivity and volumetric specific heat of the soil by employing harmonic solutions of the heat conduction equation for the same moisture group as the first step, and then we determine the SAHF using Fourier＇s law. Our results indicate that the SAHF derived from shallow earth geothermal data can reflect the heat flow field to a large extent.
基金supported bythe National Natural Science Foundation of China un-der Grants Nos40725015 and 40633017the Na-tional Basic Research Program of China under Grant No2006CB400501
文摘Data from July 2006 to June 2008 observed at SACOL （Semi-Arid Climate and Environment Observatory of Lanzhou University, 35.946°N, 104.137°E, elev. 1961 m）, a semi-arid site in Northwest China, are used to study seasonal variability of soil moisture, along with surface albedo and other soil thermal parameters, such as heat capacity, thermal conductivity and thermal diffusivity, and their relationships to soil moisture content. The results indicate that surface albedo decreases with increases in soil moisture content, showing a typical exponential relation between the surface albedo and the soil moisture. The heat capacity, the soil thermal diffusivity, and soil thermal conductivity show large variations between Julian day 90-212 and 450-578. The soil thermal conductivity is found to increase as a power function of soil moisture. Soil heat capacity and soil thermal diffusivity increase with increases in soil moisture. The SACOL observed soil moisture are also used to validate the AMSR-E/AQUA retrieved soil moisture and there is good agreement between them. The analysis of the relationship between satellite retrieved soil moisture and precipitation suggests that the variability of soil moisture depends on the variation of precipitation over the Loess Plateau.
基金the National Basic Research Program of China (973Program, 2006CB500401).
文摘Continuous observation data collected over the whole year of 2004 on a cropland surtace m Tongyu, a senti-arid area of northeastern China （44°25＇N, 122°52＇E）, have been used to investigate the variations of surface albedo and soil thermal parameters, including heat capacity, thermal conductivity and thermal diffusivity, and their relationships to soil moisture. The diurnal variation of surface albedo appears as a U shape curve on sunny days. Surface albedo decreases with the increase of solar elevation angle, and it tends to be a constant when solar elevation angle is larger than 40°. So the daily average surface albedo was computed using the data when solar elevation angle is larger than 40° Mean daily surface albedo is found to decrease with the increase of soil moisture, showing an exponential dependence on soil moisture. The variations of soil heat capacity are small during Julian days 90 300. Compared with the heat capacity, soil thermal conductivity has very gentle variations during this period, but the soil thermal diffusivity has wide variations during the same period. The soil thermal conductivity is found to increase as a power function of soil moisture. The soil thermal diffusivity increases firstly and then decreases with the increase of soil moisture.
文摘The thermal conductivity or diffusivity of pearlitic grey irons with various carbon contents is investigated by the laser flash method. The materials are cast in controlled thermal environments and produced in three dissimilar cooling rates. The cooling rate together with the carbon content largely influence the thermal conductivity of grey iron. Linear relationships exist between the thermal conductivity and the carbon content,the carbon equivalent and the fraction of former primary solidified austenite transformed into pearlite. The work shows that optimal thermal transport properties are obtained at medium cooling rates. Equations describing the thermal conductivity of pearlite,solidified as pre-eutectic austenite,and the eutectic of grey iron are derived. The thermal conductivity of pearlitic grey iron is modeled at both room temperature and elevated temperature with good accuracy.
