This study focuses on the fluorescent thermometric properties of CaMoO4:5%Tb3+under different temperature excitations.At the detection wavelength of 544 nm,with the temperature varying from 293 K to 563 K,there is a b...This study focuses on the fluorescent thermometric properties of CaMoO4:5%Tb3+under different temperature excitations.At the detection wavelength of 544 nm,with the temperature varying from 293 K to 563 K,there is a broadband absorption peak in the range of 250 nm to 350 nm.The results indicate that this phenomenon is caused by the superposition of the 4f-5d transition of Tb3+ and the O2--Mo6+charge transfer.It is considered that as the temperature rises,the luminescent intensity of the material shows an obvious continuous decreasing trend,which reflects a significant luminescent thermal quenching trend;thus,this quenching belongs to the“strong coupling”type.Based on the excitation spectrum results,two excitation wavelengths,312 nm and 338 nm,were specifically selected to excite the samples,which correspond to the top of the charge transfer band,the redshift intersection of the charge transfer band,and the edge of the charge transfer band at 293 K,respectively.展开更多
Temperature characteristics are important for the performance of organic thin film devices. On the basis of the hopping theory of Miller-Abrahams,an analytical model of charge transport for bilayer organic devices und...Temperature characteristics are important for the performance of organic thin film devices. On the basis of the hopping theory of Miller-Abrahams,an analytical model of charge transport for bilayer organic devices under the organicorganic interface limited current conduction is developed. The dependence of current, field,and carrier distribution in bilayer organic devices with the structure of ＂injection electrode/Layer Ⅰ/Layer Ⅱ/collection electrode＂ on temperature are numerically analyzed. We conclude that, for a given applied voltage, when temperature is raised, the voltage of LayerⅠ will increase,and the field will be higher. Meanwhile, the voltage of Layer Ⅲ will decrease, the field will become weaker accordingly,and the current of the device will increase.展开更多
The high temperature (300 ～480K) characteristics of the n-3C-SiC/p-Si heterojunction diodes (HJD) fabr icated by low-pressure chemical vapor deposition on Si (100) substrates are inv estigated.The obtained diode with...The high temperature (300 ～480K) characteristics of the n-3C-SiC/p-Si heterojunction diodes (HJD) fabr icated by low-pressure chemical vapor deposition on Si (100) substrates are inv estigated.The obtained diode with best rectifying properties has 1.8×104 of ratio at room temperature,and slightly rectifying characteristics with 3.1 of rectification ratio is measured at 480K of an ambient temperature .220V of reverse breakdown voltage is acquired at 300K.Capacitance-voltage char acteristics show that the abrupt junction model is applicable to the SiC/Si HJD structure and the built-in voltage is 0.75V.An ingenious equation is employed to perfectly simulate and explain the forward current density-voltage data meas ured at various temperatures.The 3C-SiC/Si HJD represents a promising approach for the fabrication of high quality heterojunction devices such as SiC-emitter heterojunction bipolar transistors.展开更多
High-speed trains often use temperature sensors to monitor the motion state of bearings.However,the temperature of bearings can be affected by factors such as weather and faults.Therefore,it is necessary to analyze in...High-speed trains often use temperature sensors to monitor the motion state of bearings.However,the temperature of bearings can be affected by factors such as weather and faults.Therefore,it is necessary to analyze in detail the relationship between the bearing temperature and influencing factors.In this study,a dynamics model of the axle box bearing of high-speed trains is established.The model can obtain the contact force between the rollers and raceway and its change law when the bearing contains outer-ring,inner-ring,and rolling-element faults.Based on the model,a thermal network method is introduced to study the temperature field distribution of the axle box bearings of high-speed trains.In this model,the heat generation,conduction,and dispersion of the isothermal nodes can be solved.The results show that the temperature of the contact point between the outer-ring raceway and rolling-elements is the highest.The relationships between the node temperature and the speed,fault type,and fault size are analyzed,finding that the higher the speed,the higher the node temperature.Under different fault types,the node temperature first increases and then decreases as the fault size increases.The effectiveness of the model is demonstrated using the actual temperature data of a high-speed train.This study proposes a thermal network model that can predict the temperature of each component of the bearings on a high-speed train under various speed and fault conditions.展开更多
Direct current （DC） and pulsed measurements are performed to determine the degradation mechanisms of A1GaN/GaN high electron mobility transistors （HEMTs） under high temperature. The degradation of the DC character...Direct current （DC） and pulsed measurements are performed to determine the degradation mechanisms of A1GaN/GaN high electron mobility transistors （HEMTs） under high temperature. The degradation of the DC characteristics is mainly attributed to the reduction in the density and the mobility of the two-dimensional electron gas （2DEG）. The pulsed measurements indicate that the trap assisted tunneling is the dominant gate leakage mechanism in the temperature range of interest. The traps in the barrier layer become active as the temperature increases, which is conducive to the electron tunneling between the gate and the channel. The enhancement of the tunneling results in the weakening of the current collapse effects, as the electrons trapped by the barrier traps can escape more easily at the higher temperature.展开更多
In order to investigate the temperature characteristics of wood during microwave(MW) treatments,optical fiber sensors were used to measure wood(Pinus sylvestris L. var. mongolica Litv.) temperatures. The results show ...In order to investigate the temperature characteristics of wood during microwave(MW) treatments,optical fiber sensors were used to measure wood(Pinus sylvestris L. var. mongolica Litv.) temperatures. The results show that the development of internal temperatures in wood basically includes two patterns during the process of MW treatment. The first may be divided into three phases: warming, constant temperature, and a sharply rising phase. The second pattern may be divided into two phases: warming, and constant temperature. The maximum temperature(MT) and rate of temperature increase(RTI)rose as the microwave power increased. The initial wood moisture content decreased while the period of constant temperature fell. Temperatures varied in different positions in the wood. The order of MT and RTI levels were the upper surface, center, bottom surface and the end point.Along the direction of wood thickness, the closer the monitoring point was to the generator, the faster the temperature increased. The MT and RTI of the end point was a minimum value because of the rapid removal of steam.展开更多
The rational design of airflow distribution is of great importance for comfort and energy conservation.Several numerical investigations of flow and temperature characteristics in cockpits have been performed to study ...The rational design of airflow distribution is of great importance for comfort and energy conservation.Several numerical investigations of flow and temperature characteristics in cockpits have been performed to study the distinct airflow distribution.This study developed the coupled heat transfer model of radiation,convection,and heat conduction for the cockpit flight environment.A three-dimensional physical model was created and a shear stress transfer(SST)k-w turbulence model was well verified with a high prediction accuracy of 91%for the experimental data.The strong inhomogeneous flow and temperature distribution were captured for various initial operating conditions(inlet temperature,inlet pressure,and gravitational acceleration).The results indicated that the common feature of the flow field was stable in the middle part of the cockpit,while the temperature field showed a large temperature gradient near the cockpit’s top region.It was also found that there was remarkable consistency in the distributed features,regardless of the applied initial operating conditions.Additionally,the mass flux and the top heat source greatly affected the flow and temperature characteristics.This study suggests that an optimized operating condition does exist and that this condition makes the flow and temperature field more stable in the cockpit.The corresponding results can provide necessary theoretical guidance for the further design of the cockpit structure.展开更多
In this paper,high temperature direct current（DC） performance of bilayer epitaxial graphene device on SiC substrate is studied in a temperature range from 25℃ to 200℃.At a gate voltage of-8 V（far from Dirac point...In this paper,high temperature direct current（DC） performance of bilayer epitaxial graphene device on SiC substrate is studied in a temperature range from 25℃ to 200℃.At a gate voltage of-8 V（far from Dirac point）,the drainsource current decreases obviously with increasing temperature,but it has little change at a gate bias of ＋8 V（near Dirac point）.The competing interactions between scattering and thermal activation are responsible for the different reduction tendencies.Four different kinds of scatterings are taken into account to qualitatively analyze the carrier mobility under different temperatures.The devices exhibit almost unchanged DC performances after high temperature measurements at 200℃ for 5 hours in air ambience,demonstrating the high thermal stabilities of the bilayer epitaxial graphene devices.展开更多
Langasite (LGS) is a novel piezoelectric crystal. The authors numerically analyses the temperature stability of surface acoustic waves (SAW) and the relation of SAW propagation with temperature on certain optimal cuts...Langasite (LGS) is a novel piezoelectric crystal. The authors numerically analyses the temperature stability of surface acoustic waves (SAW) and the relation of SAW propagation with temperature on certain optimal cuts on LGS in this paper. The results show that LGS has better temperature stability than traditional piezo crystals. The results also demonstrate that the velocity of SAW decrease with temperature, the electro-mechanical coupling constant (k2) and temperature coefficient of frequency increases parabolically and the power flow angle increases linearly on certain optimal cuts of LGS. The calculation result compared with the experimental and show good agreement.展开更多
The temperature characteristics of VCSEL using proton implantation are described,compared with its edge-emitting counterpart.Implant-confined VCSEL operation has been realized up to 120 ℃.These records of high operat...The temperature characteristics of VCSEL using proton implantation are described,compared with its edge-emitting counterpart.Implant-confined VCSEL operation has been realized up to 120 ℃.These records of high operating temperature are caused by high characteristic temperature. The relevant physical mechanisms including their dependence on temperature and carrier density are considered. The temperature sensitivity of the threshold current is not strongly increasing with higher temperature.展开更多
The resolution expression for the temperature dependence of the current and threshold voltage is deduced as well as the analysis of temperature characteristics of BJMOSFET. Equivalent circuit of analysis and simulatio...The resolution expression for the temperature dependence of the current and threshold voltage is deduced as well as the analysis of temperature characteristics of BJMOSFET. Equivalent circuit of analysis and simulation has been established for the BJMOSFET temperature characteristics. By using the general circuit simulation software of PSpice9 and computer simulation, characteristic graphs of the BJMOSFET output characteristic, transient characteristic and amplitude-frequency characteristic with temperature variation are obtained. The results accorded very good with theoretical analysis and proved that BJMOSFET has better temperature characteristics than traditional MOSFET.展开更多
Cavity perturbation method was used to determine the dielectric properties （ε′,ε″, and tanδ） of zinc oxide dust in different apparent densities. The process was conducted to study the microwave-absorption prope...Cavity perturbation method was used to determine the dielectric properties （ε′,ε″, and tanδ） of zinc oxide dust in different apparent densities. The process was conducted to study the microwave-absorption properties of zinc oxide dust and the feasibility of microwave roasting zinc oxide dust to remove fluorine and chlorine. The dielectric constant, dielectric loss, and loss tangent were proportional to the apparent density of zinc oxide dust. The effects of sample mass and microwave power on the temperature increase characteristics under the microwave field were also studied. The results show that the apparent heating rate of the zinc oxide dust increases with the increase in microwave roasting power and decreases with the increase in the sample mass. The temperature of the samples reaches approximately 800 ＆#176;C after microwave treatment for 8 min, which indicates that the zinc oxide dust has strong microwave-absorption ability.展开更多
Based on the method of linear trending,analysis was made upon the daily temperature statistics of Meitan County from 1951 to 2009,and the results showed that the temperature in general was on the rise.With 1980 as the...Based on the method of linear trending,analysis was made upon the daily temperature statistics of Meitan County from 1951 to 2009,and the results showed that the temperature in general was on the rise.With 1980 as the turning point,it was on the decline before while later the temperature increased quickly.Among these figures,the variation rates of annual average temperature,annual maximum temperature,and annual minimum temperature are 0.11 ℃/10 a,0.08 ℃/10 a,and 0.36 ℃/10 a.The variation rates of average temperature in spring,summer,fall and winter are respectively 0.12 ℃/10 a,0.07 ℃/10 a,0.12 ℃/10 a,and 0.13 ℃/10 a.Morlet wavelet was adopted to analyze the periodicity of temperature change which has periods of different scales.But since 2000,during different time scales most of the areas have been in the period of temperature rises.Besides,certain rule exists in the periodicity of maximum temperature and minimum temperature.Before 1970s,they had opposite changing rules,and the alteration of the peak value occurred.However,in the late 1980s,they had similar changing rules,and their peak values appeared at the same time.It means that against the background of global warming,the reaction of temperature evolution in Meitan County is quite remarkable.展开更多
Different from the traditional way of using piezoelectric （PZT）phase shifter to measure phase difference, a new method is designed to calculate it between signals in the two arms of a homodyne fiber interferometer. ...Different from the traditional way of using piezoelectric （PZT）phase shifter to measure phase difference, a new method is designed to calculate it between signals in the two arms of a homodyne fiber interferometer. A simple homodyne fiber interferometer system is then established to measure the interference photoeurrent and the photocurrents from the two fiber arms generated by the signal power on a temperature control plat. The homodyne fiber interferometer system is composed of fiber and sensitive to the variation of temperature. Thus, is necessary to study the temperature characteristics in the phase measurement of homodyne fiber interferometer. The experimental results show that the variation of the phase difference of signals in the two fiber arms is proportional to the variation of temperature.展开更多
The reduction degradation characteristics of typical sinter, pellet and lump ore were tested with the reducing gas conditions simulating two kinds of irowmaking processes. The results show that, in the same condition ...The reduction degradation characteristics of typical sinter, pellet and lump ore were tested with the reducing gas conditions simulating two kinds of irowmaking processes. The results show that, in the same condition of gas composition and temperature, the reduction degradation degree （RDI〈3.15mm） of sinter is high, RDI〈3.15mm of lump ore is low and RDI〈3.15 mm of pellet is in the middle level. With two kinds of gas composition simulating different iron-making processes, the reduction degradation indices （RDI） of three kinds of iron ores all present the tenden- cy of ＂inverted V-shape＂ in the temperature range from 450 to 650℃, and the RDI reach the maximum value at 550℃. The reduction degradation degrees of iron ores are extended when mixing the gas with hydrogen to increase the re duction potential, and the influence extent is discrepant for different iron ores. Colligating the increase amplitude of grains in small size fraction, the influence of reducing gas on lump ore is the greatest, the influence on sinter is the second, and the sensitivity of pellet on the reducing gas properties change is relatively small. As for the degradation form, lump ore and sinter both present the degradation ,of cracking, and the distribution of small grains generated from the cracking is in the range from 03 5 to 6. 3 mm uniformly. The lump ore presents surface cracking, while sin- ter presents integral cracking. The pellet presents the degradation of surface stripping, and the proportion of grains smaller than 0.5 mm is the highest, which is up to 90% in the grains smaller than 3.15 mm.展开更多
To avoid the nonuniform phenomena of heat and mass transfer of metallurgical powdery materials caused by conventional heating method,the temperature rise characteristics of carbon-containing chromite ore fines in the ...To avoid the nonuniform phenomena of heat and mass transfer of metallurgical powdery materials caused by conventional heating method,the temperature rise characteristics of carbon-containing chromite ore fines in the microwave field were investigated using microwave heating in a microwave metallurgical furnace.The experimental results show that the carbon-containing chromite ore fines have better temperature rise characteristics in the microwave field at a frequency of 2.45 GHz.After heated in the microwave field of 10 kW,the temperature of 1 kg carbon-containing chromite ore fines rose up to 1 100 ℃ in 7 min,at a temperature rise rate of 157.1（℃·min-1·kg-1）,whereas the temperature of 1 kg carbon-containing magnetite ore fines rose only up to 1 000 ℃ in 10 min,at a temperature rise rate of 100（℃·min-1·kg-1）.With increasing carbon-fitting ratios and by adding calcic lime,their heating effects changed regularly.展开更多
The rupture behavior of a cast Ni-base superalloy M963 at high temperature has been investi- gated. The microstructure examination shows that there exists a large amount of the carbide and γ-γ' eutectic, which i...The rupture behavior of a cast Ni-base superalloy M963 at high temperature has been investi- gated. The microstructure examination shows that there exists a large amount of the carbide and γ-γ' eutectic, which is very harmful to the mechanical properties of M963 superalloy. The tensile strength of M963 superalloy both at room temperature and at high temperatures is higher than that of K17G alloy, but the tensile ductility of the former is much lower than that of the latter. In tensile fracture process with the high strain rate, the open carbides are the initiation site and the carbide/matrix interface is the propagation path of cracks. But in fracture process with the low strain rate, the carbide/matrix interface and cast microvoids are the initiation sites, and the carbide/matrix interface is the propagation path of cracks. The effective ways to improve ductility of M963 superalloy are also suggested.展开更多
With the series of annual and seasonal temperature during 1957 – 2001 in Dongguan, Guangdong, the statistical characteristic and power spectrum and secular trend and sudden change phenomena are computed in this paper...With the series of annual and seasonal temperature during 1957 – 2001 in Dongguan, Guangdong, the statistical characteristic and power spectrum and secular trend and sudden change phenomena are computed in this paper. From the results it is known that (1) the temperatures have obvious characteristics of monsoon climate but do not have normal distribution, showing biased distribution of high or low kurtosis; (2) over the recent half- century, the temperatures tend to rise, specially in the last 10 years, in which mean temperature have quickly ascended by about 1.5°C, and except for the spring, there were sudden change of seasonal temperature rising from the 1980’s to 1990’s, which really reflected the influence of developing and opening and urbanization on Dongguan temperature; (3) except for the spring, the temperature of other seasons show some oscillatory periods in Dongguan and some of them also include long-term variation trends.展开更多
The effect of thermal cycling and aging in martensitic state in Ti-Pd-Ni alloys were investigated by DSC and TEM observations. It is shown that the thermal cycling causes the decreases in M, and Af temperatures in Ti5...The effect of thermal cycling and aging in martensitic state in Ti-Pd-Ni alloys were investigated by DSC and TEM observations. It is shown that the thermal cycling causes the decreases in M, and Af temperatures in Ti50Pd50-xNix (x=10, 20, 30) alloys, but no obvious thermal cycling effect was observed in Ti50Pd50Pd40Ni10 alloys and the aging effect shows a curious feature, i.e., the Af temperature does not saturate even after relatively long time aging, which is considered to be due to the occurrence of recovery recrystallization during aging.展开更多
The effects of Cr content and annealing temperature on abrasive wear characteristics of cast ausferrite nodular iron were investigated with Suga type abrasive wear tester. The surface morphology and Vickers hardness o...The effects of Cr content and annealing temperature on abrasive wear characteristics of cast ausferrite nodular iron were investigated with Suga type abrasive wear tester. The surface morphology and Vickers hardness of the tested samples were analyzed by scanning electron microscopy（SEM）, digital microscope and Vickers hardness tester. The results show that the cast ausferrite nodular iron could be obtained by alloying with Cr in the as-cast ductile cast iron and permanent mold casting, and the bainite content in the matrix increased with increasing Cr content. However, the decomposition of bainite took place during annealing at 500 °C to 800 °C; especially, at 800 °C, the bainite transformed into a mixture of fine lamellar pearlite and ferrite matrix structure. The wear loss of specimens was reduced with increasing Cr content in the cast ausferrite nodular iron. The wear loss of the sample cast ausferrite nodular iron with 0.4mass% Cr is the least. The wear loss began to increase while the Cr content is 0.6mass%. The wear loss of annealed ductile irons at different annealing temperatures was higher than that of as-cast samples. During the abrasive wear, the shear stress transformed austenite to martensite, and the hardness of specimens increased and the wear resistance of as-cast ductile cast iron was improved.展开更多
基金Basic Scientific Research Operating Expenses Project of Provincial Undergraduate Colleges and Universities in Heilongjiang Province:Study on Luminescent Properties and Fluorescent Temperature Characteristics of Rare Earth Luminescent Materials Based on Tungstates(YWK10236210223)Provincial General Project:College Students’Innovation and Entrepreneurship Training Program Project:Design of a Multifunctional Intelligent Car(202310236033)。
文摘This study focuses on the fluorescent thermometric properties of CaMoO4:5%Tb3+under different temperature excitations.At the detection wavelength of 544 nm,with the temperature varying from 293 K to 563 K,there is a broadband absorption peak in the range of 250 nm to 350 nm.The results indicate that this phenomenon is caused by the superposition of the 4f-5d transition of Tb3+ and the O2--Mo6+charge transfer.It is considered that as the temperature rises,the luminescent intensity of the material shows an obvious continuous decreasing trend,which reflects a significant luminescent thermal quenching trend;thus,this quenching belongs to the“strong coupling”type.Based on the excitation spectrum results,two excitation wavelengths,312 nm and 338 nm,were specifically selected to excite the samples,which correspond to the top of the charge transfer band,the redshift intersection of the charge transfer band,and the edge of the charge transfer band at 293 K,respectively.
文摘Temperature characteristics are important for the performance of organic thin film devices. On the basis of the hopping theory of Miller-Abrahams,an analytical model of charge transport for bilayer organic devices under the organicorganic interface limited current conduction is developed. The dependence of current, field,and carrier distribution in bilayer organic devices with the structure of ＂injection electrode/Layer Ⅰ/Layer Ⅱ/collection electrode＂ on temperature are numerically analyzed. We conclude that, for a given applied voltage, when temperature is raised, the voltage of LayerⅠ will increase,and the field will be higher. Meanwhile, the voltage of Layer Ⅲ will decrease, the field will become weaker accordingly,and the current of the device will increase.
文摘The high temperature (300 ～480K) characteristics of the n-3C-SiC/p-Si heterojunction diodes (HJD) fabr icated by low-pressure chemical vapor deposition on Si (100) substrates are inv estigated.The obtained diode with best rectifying properties has 1.8×104 of ratio at room temperature,and slightly rectifying characteristics with 3.1 of rectification ratio is measured at 480K of an ambient temperature .220V of reverse breakdown voltage is acquired at 300K.Capacitance-voltage char acteristics show that the abrupt junction model is applicable to the SiC/Si HJD structure and the built-in voltage is 0.75V.An ingenious equation is employed to perfectly simulate and explain the forward current density-voltage data meas ured at various temperatures.The 3C-SiC/Si HJD represents a promising approach for the fabrication of high quality heterojunction devices such as SiC-emitter heterojunction bipolar transistors.
基金National Key R&D Program(Grant No.2020YFB2007700),National Natural Science Foundation of China(Grant Nos.11790282,12032017,12002221 and 11872256)S&T Program of Hebei(Grant No.20310803D)+1 种基金Natural Science Foundation of Hebei Province(Grant No.A2020210028)State Foundation for Studying Abroad.
文摘High-speed trains often use temperature sensors to monitor the motion state of bearings.However,the temperature of bearings can be affected by factors such as weather and faults.Therefore,it is necessary to analyze in detail the relationship between the bearing temperature and influencing factors.In this study,a dynamics model of the axle box bearing of high-speed trains is established.The model can obtain the contact force between the rollers and raceway and its change law when the bearing contains outer-ring,inner-ring,and rolling-element faults.Based on the model,a thermal network method is introduced to study the temperature field distribution of the axle box bearings of high-speed trains.In this model,the heat generation,conduction,and dispersion of the isothermal nodes can be solved.The results show that the temperature of the contact point between the outer-ring raceway and rolling-elements is the highest.The relationships between the node temperature and the speed,fault type,and fault size are analyzed,finding that the higher the speed,the higher the node temperature.Under different fault types,the node temperature first increases and then decreases as the fault size increases.The effectiveness of the model is demonstrated using the actual temperature data of a high-speed train.This study proposes a thermal network model that can predict the temperature of each component of the bearings on a high-speed train under various speed and fault conditions.
基金supported by the National Natural Science Foundation of China(Grant No.60736033)
文摘Direct current （DC） and pulsed measurements are performed to determine the degradation mechanisms of A1GaN/GaN high electron mobility transistors （HEMTs） under high temperature. The degradation of the DC characteristics is mainly attributed to the reduction in the density and the mobility of the two-dimensional electron gas （2DEG）. The pulsed measurements indicate that the trap assisted tunneling is the dominant gate leakage mechanism in the temperature range of interest. The traps in the barrier layer become active as the temperature increases, which is conducive to the electron tunneling between the gate and the channel. The enhancement of the tunneling results in the weakening of the current collapse effects, as the electrons trapped by the barrier traps can escape more easily at the higher temperature.
基金financially supported by the National‘‘Twelfth Five-Year’’ Plan for Science&Technology(No.2015BAD14B04)the Special Fund for Forest Scientific Research in the Public Interest of China(No.201404516)
文摘In order to investigate the temperature characteristics of wood during microwave(MW) treatments,optical fiber sensors were used to measure wood(Pinus sylvestris L. var. mongolica Litv.) temperatures. The results show that the development of internal temperatures in wood basically includes two patterns during the process of MW treatment. The first may be divided into three phases: warming, constant temperature, and a sharply rising phase. The second pattern may be divided into two phases: warming, and constant temperature. The maximum temperature(MT) and rate of temperature increase(RTI)rose as the microwave power increased. The initial wood moisture content decreased while the period of constant temperature fell. Temperatures varied in different positions in the wood. The order of MT and RTI levels were the upper surface, center, bottom surface and the end point.Along the direction of wood thickness, the closer the monitoring point was to the generator, the faster the temperature increased. The MT and RTI of the end point was a minimum value because of the rapid removal of steam.
基金the Fundamental Research Funds for the Central Universities.(Project No.31020190504004).
文摘The rational design of airflow distribution is of great importance for comfort and energy conservation.Several numerical investigations of flow and temperature characteristics in cockpits have been performed to study the distinct airflow distribution.This study developed the coupled heat transfer model of radiation,convection,and heat conduction for the cockpit flight environment.A three-dimensional physical model was created and a shear stress transfer(SST)k-w turbulence model was well verified with a high prediction accuracy of 91%for the experimental data.The strong inhomogeneous flow and temperature distribution were captured for various initial operating conditions(inlet temperature,inlet pressure,and gravitational acceleration).The results indicated that the common feature of the flow field was stable in the middle part of the cockpit,while the temperature field showed a large temperature gradient near the cockpit’s top region.It was also found that there was remarkable consistency in the distributed features,regardless of the applied initial operating conditions.Additionally,the mass flux and the top heat source greatly affected the flow and temperature characteristics.This study suggests that an optimized operating condition does exist and that this condition makes the flow and temperature field more stable in the cockpit.The corresponding results can provide necessary theoretical guidance for the further design of the cockpit structure.
基金Project supported by the National Natural Science Foundation of China(Grant No.61306006)
文摘In this paper,high temperature direct current（DC） performance of bilayer epitaxial graphene device on SiC substrate is studied in a temperature range from 25℃ to 200℃.At a gate voltage of-8 V（far from Dirac point）,the drainsource current decreases obviously with increasing temperature,but it has little change at a gate bias of ＋8 V（near Dirac point）.The competing interactions between scattering and thermal activation are responsible for the different reduction tendencies.Four different kinds of scatterings are taken into account to qualitatively analyze the carrier mobility under different temperatures.The devices exhibit almost unchanged DC performances after high temperature measurements at 200℃ for 5 hours in air ambience,demonstrating the high thermal stabilities of the bilayer epitaxial graphene devices.
文摘Langasite (LGS) is a novel piezoelectric crystal. The authors numerically analyses the temperature stability of surface acoustic waves (SAW) and the relation of SAW propagation with temperature on certain optimal cuts on LGS in this paper. The results show that LGS has better temperature stability than traditional piezo crystals. The results also demonstrate that the velocity of SAW decrease with temperature, the electro-mechanical coupling constant (k2) and temperature coefficient of frequency increases parabolically and the power flow angle increases linearly on certain optimal cuts of LGS. The calculation result compared with the experimental and show good agreement.
文摘The temperature characteristics of VCSEL using proton implantation are described,compared with its edge-emitting counterpart.Implant-confined VCSEL operation has been realized up to 120 ℃.These records of high operating temperature are caused by high characteristic temperature. The relevant physical mechanisms including their dependence on temperature and carrier density are considered. The temperature sensitivity of the threshold current is not strongly increasing with higher temperature.
文摘The resolution expression for the temperature dependence of the current and threshold voltage is deduced as well as the analysis of temperature characteristics of BJMOSFET. Equivalent circuit of analysis and simulation has been established for the BJMOSFET temperature characteristics. By using the general circuit simulation software of PSpice9 and computer simulation, characteristic graphs of the BJMOSFET output characteristic, transient characteristic and amplitude-frequency characteristic with temperature variation are obtained. The results accorded very good with theoretical analysis and proved that BJMOSFET has better temperature characteristics than traditional MOSFET.
基金Project(51104073)supported by the National Natural Science Foundation of ChinaProject(2014CB643404)supported by the National Basic Research Program of China+1 种基金Project(2013AA064003)supported by the Hi-tech Research and Development Program of ChinaProject(2012HB008)supported by the Yunnan Provincial Young Academic Technology Leader Reserve Talents,China
文摘Cavity perturbation method was used to determine the dielectric properties （ε′,ε″, and tanδ） of zinc oxide dust in different apparent densities. The process was conducted to study the microwave-absorption properties of zinc oxide dust and the feasibility of microwave roasting zinc oxide dust to remove fluorine and chlorine. The dielectric constant, dielectric loss, and loss tangent were proportional to the apparent density of zinc oxide dust. The effects of sample mass and microwave power on the temperature increase characteristics under the microwave field were also studied. The results show that the apparent heating rate of the zinc oxide dust increases with the increase in microwave roasting power and decreases with the increase in the sample mass. The temperature of the samples reaches approximately 800 ＆#176;C after microwave treatment for 8 min, which indicates that the zinc oxide dust has strong microwave-absorption ability.
基金Supported by National Basic Research Program of China (973 Pro-gram) (2010CB951102 )Program of Innovation ResearchGroup (51021006),National Natural Science Foundation of China~~
文摘Based on the method of linear trending,analysis was made upon the daily temperature statistics of Meitan County from 1951 to 2009,and the results showed that the temperature in general was on the rise.With 1980 as the turning point,it was on the decline before while later the temperature increased quickly.Among these figures,the variation rates of annual average temperature,annual maximum temperature,and annual minimum temperature are 0.11 ℃/10 a,0.08 ℃/10 a,and 0.36 ℃/10 a.The variation rates of average temperature in spring,summer,fall and winter are respectively 0.12 ℃/10 a,0.07 ℃/10 a,0.12 ℃/10 a,and 0.13 ℃/10 a.Morlet wavelet was adopted to analyze the periodicity of temperature change which has periods of different scales.But since 2000,during different time scales most of the areas have been in the period of temperature rises.Besides,certain rule exists in the periodicity of maximum temperature and minimum temperature.Before 1970s,they had opposite changing rules,and the alteration of the peak value occurred.However,in the late 1980s,they had similar changing rules,and their peak values appeared at the same time.It means that against the background of global warming,the reaction of temperature evolution in Meitan County is quite remarkable.
基金supported by the National Natural Science Foundation of China (60372061)Basic Fund for the Scientific Research Project of Jilin University (200903296)
文摘Different from the traditional way of using piezoelectric （PZT）phase shifter to measure phase difference, a new method is designed to calculate it between signals in the two arms of a homodyne fiber interferometer. A simple homodyne fiber interferometer system is then established to measure the interference photoeurrent and the photocurrents from the two fiber arms generated by the signal power on a temperature control plat. The homodyne fiber interferometer system is composed of fiber and sensitive to the variation of temperature. Thus, is necessary to study the temperature characteristics in the phase measurement of homodyne fiber interferometer. The experimental results show that the variation of the phase difference of signals in the two fiber arms is proportional to the variation of temperature.
文摘The reduction degradation characteristics of typical sinter, pellet and lump ore were tested with the reducing gas conditions simulating two kinds of irowmaking processes. The results show that, in the same condition of gas composition and temperature, the reduction degradation degree （RDI〈3.15mm） of sinter is high, RDI〈3.15mm of lump ore is low and RDI〈3.15 mm of pellet is in the middle level. With two kinds of gas composition simulating different iron-making processes, the reduction degradation indices （RDI） of three kinds of iron ores all present the tenden- cy of ＂inverted V-shape＂ in the temperature range from 450 to 650℃, and the RDI reach the maximum value at 550℃. The reduction degradation degrees of iron ores are extended when mixing the gas with hydrogen to increase the re duction potential, and the influence extent is discrepant for different iron ores. Colligating the increase amplitude of grains in small size fraction, the influence of reducing gas on lump ore is the greatest, the influence on sinter is the second, and the sensitivity of pellet on the reducing gas properties change is relatively small. As for the degradation form, lump ore and sinter both present the degradation ,of cracking, and the distribution of small grains generated from the cracking is in the range from 03 5 to 6. 3 mm uniformly. The lump ore presents surface cracking, while sin- ter presents integral cracking. The pellet presents the degradation of surface stripping, and the proportion of grains smaller than 0.5 mm is the highest, which is up to 90% in the grains smaller than 3.15 mm.
基金Item Sponsored by National Natural Science Foundation of China and Baoshan Iron and Steel Group Co(50474083)
文摘To avoid the nonuniform phenomena of heat and mass transfer of metallurgical powdery materials caused by conventional heating method,the temperature rise characteristics of carbon-containing chromite ore fines in the microwave field were investigated using microwave heating in a microwave metallurgical furnace.The experimental results show that the carbon-containing chromite ore fines have better temperature rise characteristics in the microwave field at a frequency of 2.45 GHz.After heated in the microwave field of 10 kW,the temperature of 1 kg carbon-containing chromite ore fines rose up to 1 100 ℃ in 7 min,at a temperature rise rate of 157.1（℃·min-1·kg-1）,whereas the temperature of 1 kg carbon-containing magnetite ore fines rose only up to 1 000 ℃ in 10 min,at a temperature rise rate of 100（℃·min-1·kg-1）.With increasing carbon-fitting ratios and by adding calcic lime,their heating effects changed regularly.
基金supported by the Postdoctoral Science Foundation of China
文摘The rupture behavior of a cast Ni-base superalloy M963 at high temperature has been investi- gated. The microstructure examination shows that there exists a large amount of the carbide and γ-γ' eutectic, which is very harmful to the mechanical properties of M963 superalloy. The tensile strength of M963 superalloy both at room temperature and at high temperatures is higher than that of K17G alloy, but the tensile ductility of the former is much lower than that of the latter. In tensile fracture process with the high strain rate, the open carbides are the initiation site and the carbide/matrix interface is the propagation path of cracks. But in fracture process with the low strain rate, the carbide/matrix interface and cast microvoids are the initiation sites, and the carbide/matrix interface is the propagation path of cracks. The effective ways to improve ductility of M963 superalloy are also suggested.
文摘With the series of annual and seasonal temperature during 1957 – 2001 in Dongguan, Guangdong, the statistical characteristic and power spectrum and secular trend and sudden change phenomena are computed in this paper. From the results it is known that (1) the temperatures have obvious characteristics of monsoon climate but do not have normal distribution, showing biased distribution of high or low kurtosis; (2) over the recent half- century, the temperatures tend to rise, specially in the last 10 years, in which mean temperature have quickly ascended by about 1.5°C, and except for the spring, there were sudden change of seasonal temperature rising from the 1980’s to 1990’s, which really reflected the influence of developing and opening and urbanization on Dongguan temperature; (3) except for the spring, the temperature of other seasons show some oscillatory periods in Dongguan and some of them also include long-term variation trends.
基金This work was supported by a Grant-in-Aid fOrEncouragement of Young Scientists (W.C.) (l998-1999) from the Ministry of Educat
文摘The effect of thermal cycling and aging in martensitic state in Ti-Pd-Ni alloys were investigated by DSC and TEM observations. It is shown that the thermal cycling causes the decreases in M, and Af temperatures in Ti50Pd50-xNix (x=10, 20, 30) alloys, but no obvious thermal cycling effect was observed in Ti50Pd50Pd40Ni10 alloys and the aging effect shows a curious feature, i.e., the Af temperature does not saturate even after relatively long time aging, which is considered to be due to the occurrence of recovery recrystallization during aging.
基金Item Sponsored by Important National Science and Technology Specific Project of China(2012ZX04010-031)
文摘The effects of Cr content and annealing temperature on abrasive wear characteristics of cast ausferrite nodular iron were investigated with Suga type abrasive wear tester. The surface morphology and Vickers hardness of the tested samples were analyzed by scanning electron microscopy（SEM）, digital microscope and Vickers hardness tester. The results show that the cast ausferrite nodular iron could be obtained by alloying with Cr in the as-cast ductile cast iron and permanent mold casting, and the bainite content in the matrix increased with increasing Cr content. However, the decomposition of bainite took place during annealing at 500 °C to 800 °C; especially, at 800 °C, the bainite transformed into a mixture of fine lamellar pearlite and ferrite matrix structure. The wear loss of specimens was reduced with increasing Cr content in the cast ausferrite nodular iron. The wear loss of the sample cast ausferrite nodular iron with 0.4mass% Cr is the least. The wear loss began to increase while the Cr content is 0.6mass%. The wear loss of annealed ductile irons at different annealing temperatures was higher than that of as-cast samples. During the abrasive wear, the shear stress transformed austenite to martensite, and the hardness of specimens increased and the wear resistance of as-cast ductile cast iron was improved.
