Non-destructive techniques of in-situ stress measurement from oriented cored rocks have great potential to be developed as a cost cost-effective and reliable alternative to the conventional overcoring and hydraulic fr...Non-destructive techniques of in-situ stress measurement from oriented cored rocks have great potential to be developed as a cost cost-effective and reliable alternative to the conventional overcoring and hydraulic fracturing methods.The tangent modulus method(TMM)is one such technique that can be applied to oriented cored rocks to measure in-situ stresses.Like the deformation rate analysis(DRA),the rock specimen is subjected to two cycles of uniaxial compression and the stress-tangent modulus curve for the two cycles is obtained from the stress-strain curve.A bending point in the tangent modulus curve of the first cycle is observed,separating it from the tangent modulus curve of the second cycle.The point of separation between the two curves is assumed to be the previously applied maximum stress.A number of experiments were conducted on coal and coal measured rocks(sandstone and limestone)to understand the effect of loading conditions and the time delay.The specimens were preloaded,and cyclic compressions were applied under three different modes of loading,four different strain rates,and time delays of up to one week.The bending point in the stress-tangent modulus curves occurred approximately at the applied pre-stress levels under all three loading modes,and no effect of loading rate was observed on the bending points in TMM.However,a clear effect of time delay was observed on the TMM,contradicting the DRA results.This could be due to the sensitivity of TMM and the range of its applicability,all of which need further investigation for the in-situ stress measurement.展开更多
This paper presents an elasto-viscoplastic consistent tangent operator (CTO) based boundary element formulation, and application for calculation of path-domain independentJ integrals (extension of the classicalJ integ...This paper presents an elasto-viscoplastic consistent tangent operator (CTO) based boundary element formulation, and application for calculation of path-domain independentJ integrals (extension of the classicalJ integrals) in nonlinear crack analysis. When viscoplastic deformation happens, the effective stresses around the crack tip in the nonlinear region is allowed to exceed the loading surface, and the pure plastic theory is not suitable for this situation. The concept of consistency employed in the solution of increment viscoplastic problem, plays a crucial role in preserving the quadratic rate asymptotic convergence of iteractive schemes based on Newton's method. Therefore, this paper investigates the viscoplastic crack problem, and presents an implicit viscoplastic algorithm using the CTO concept in a boundary element framework for path-domain independentJ integrals. Applications are presented with two numerical examples for viscoplastic crack problems andJ integrals.展开更多
基金financially supported by the Australian Coal Association Research Program(ACARP)under project C29010.
文摘Non-destructive techniques of in-situ stress measurement from oriented cored rocks have great potential to be developed as a cost cost-effective and reliable alternative to the conventional overcoring and hydraulic fracturing methods.The tangent modulus method(TMM)is one such technique that can be applied to oriented cored rocks to measure in-situ stresses.Like the deformation rate analysis(DRA),the rock specimen is subjected to two cycles of uniaxial compression and the stress-tangent modulus curve for the two cycles is obtained from the stress-strain curve.A bending point in the tangent modulus curve of the first cycle is observed,separating it from the tangent modulus curve of the second cycle.The point of separation between the two curves is assumed to be the previously applied maximum stress.A number of experiments were conducted on coal and coal measured rocks(sandstone and limestone)to understand the effect of loading conditions and the time delay.The specimens were preloaded,and cyclic compressions were applied under three different modes of loading,four different strain rates,and time delays of up to one week.The bending point in the stress-tangent modulus curves occurred approximately at the applied pre-stress levels under all three loading modes,and no effect of loading rate was observed on the bending points in TMM.However,a clear effect of time delay was observed on the TMM,contradicting the DRA results.This could be due to the sensitivity of TMM and the range of its applicability,all of which need further investigation for the in-situ stress measurement.
基金The project supported by National Natural Science Foundation of China(9713008)Zhejiang Natural Science Foundation Special Funds No. RC.9601
文摘This paper presents an elasto-viscoplastic consistent tangent operator (CTO) based boundary element formulation, and application for calculation of path-domain independentJ integrals (extension of the classicalJ integrals) in nonlinear crack analysis. When viscoplastic deformation happens, the effective stresses around the crack tip in the nonlinear region is allowed to exceed the loading surface, and the pure plastic theory is not suitable for this situation. The concept of consistency employed in the solution of increment viscoplastic problem, plays a crucial role in preserving the quadratic rate asymptotic convergence of iteractive schemes based on Newton's method. Therefore, this paper investigates the viscoplastic crack problem, and presents an implicit viscoplastic algorithm using the CTO concept in a boundary element framework for path-domain independentJ integrals. Applications are presented with two numerical examples for viscoplastic crack problems andJ integrals.
