Powdering/exfoliating of coatings and scratching galvanized steels and high strength steels （HSS）, are the main forms of surface damage in the forming of which result in increased die maintenance cost and scrap rate...Powdering/exfoliating of coatings and scratching galvanized steels and high strength steels （HSS）, are the main forms of surface damage in the forming of which result in increased die maintenance cost and scrap rate. In this study, a special rectangular box was developed to investigate the behavior and characteristics of surface damage in sheet metal forming （SMF） processes. U-channel forming tests were conducted to study the effect of tool hardness on surface damage in the forming of high strength steels and galvanized steels （hot-dip galvanized and galvannealed steels）. Experimental results indicate that sheet deformation mode influences the severity of surface damage in SMF and surface damage occurs easily at the regions where sheet specimen deforms under the action of compressive stress. Die corner is the position where surface damage initiates. For HSS sheet, surface damage is of major interest due to high forming pressure. The HSS and hot-dip galvanized steels show improved ability of damage-resistance with increased hardness of the forming tool. However, for galvannealed steel it is not the forming tool with the highest hardness value that performs best.展开更多
Bone cutting is of importance in orthopaedic surgery but is also challenging due to its nature of brittleness—where severe mechanical and thermal damages can be introduced easily in conventional machining.Laser machi...Bone cutting is of importance in orthopaedic surgery but is also challenging due to its nature of brittleness—where severe mechanical and thermal damages can be introduced easily in conventional machining.Laser machining is a new technology that can allow for complex cut geometries whilst minimising surface defects i.e.,smearing,which occur in mechanical methods.However,comparative studies on the influence of lasers with different pulse characteristics on necrotic damage and surface integrity have not been reported yet.This paper for the first time investigates the effects of laser type on the necrotic damage and surface integrity in fresh bovine cortical bone after ex-situ laser machining.Three lasers of different pulse widths,i.e.,picosecond,nanosecond and continuous wave lasers have been investigated with different feed speeds tested to study the machining efficiency.The cutting temperature,and geometrical outputs have been measured to investigate the thermal influence on the cooling behaviour of the bone samples while high-speed imaging was used to compare the material removal mechanisms between a pulsed and continuous wave laser.Furthermore,an in-depth histological analysis of the subsurface has revealed that the nanosecond laser caused the largest necrotic depth,owing to the high pulse frequency limiting the dissipation of heat.It has also been observed that surface cracks positioned perpendicular to the trench direction were produced after machining by the picosecond laser,indicative of the photomechanical effect induced by plasma explosions.Therefore,the choice of laser type(i.e.,in terms of its pulse width and frequency)needs to be critically considered for appropriate application during laser osteotomy with minimum damage and improved healing.展开更多
Two complementary types NPN and PNP of bipolar junction transistors （BJTs） were exposed to higll dose of neutrons and gamma rays. The change in the base and collector currents, minority carriers lifetime, and curren...Two complementary types NPN and PNP of bipolar junction transistors （BJTs） were exposed to higll dose of neutrons and gamma rays. The change in the base and collector currents, minority carriers lifetime, and current gain factor/3 with respect to the dose were analyzed. The contributions of the base current according to the defect types were also reported. It was declared that the radiation effect of neutrons was almost similar between the two transistor types, this effect at high dose may decrease the value of/3 to less than one. The Messenger-Spratt equation was used to describe the experimental results in this case. However, the experimental data demonstrated that the effect of gamma rays was generally higher on NPN than PNP transistors. This is mainly attributed to the difference in the behavior of the trapped positive charges in the SiO2 layers. Meanwhile, this difference tends to be small for high gamma dose.展开更多
The surface damage and the damage depth in wire-cut silicon wafers and inner-diameter (ID) cut silicon wafers were studied by means of thickness meter, scanning electron microscopy (SEM) and double crystal X-ray diffr...The surface damage and the damage depth in wire-cut silicon wafers and inner-diameter (ID) cut silicon wafers were studied by means of thickness meter, scanning electron microscopy (SEM) and double crystal X-ray diffractometer. The results show that the surface of wire-cut silicon wafers is rougher than that of ID-cut silicon wafers and the surface damage in wire-cut silicon wafers is more serious than that in ID-cut silicon wafers, while the damage depth in wire-cut silicon wafers is smaller than that in ID-cut silicon wafers. The possible reasons for the generation of surface damage in wire-cut silicon wafers were also discussed.展开更多
This letter reports experimental observation of a direct correlation between the acoustic nonlinearity parameter (NP) measured with nonlinear Rayleigh waves and the accumulation of plasticity damage in an AZ31 magnesi...This letter reports experimental observation of a direct correlation between the acoustic nonlinearity parameter (NP) measured with nonlinear Rayleigh waves and the accumulation of plasticity damage in an AZ31 magnesium alloy plate specimen.Rayleigh waves are generated and detected with wedge transducers,and the NPs are measured at different stress levels.The results show that there is a significant increase in the NPs with monotonic tensile loads surpassing the material’s yielding stress.The research suggests an effective nondestructive evaluation method to track the surface damage in metals.展开更多
In this paper, damages and annealing effects of X,Y and Z cut LiNbO-3 implanted by 350keV high energy Ti (1.5 x 10<sup>17</sup> / cm<sup>2</sup>) are studied. The surface damages of X,Y cut pla...In this paper, damages and annealing effects of X,Y and Z cut LiNbO-3 implanted by 350keV high energy Ti (1.5 x 10<sup>17</sup> / cm<sup>2</sup>) are studied. The surface damages of X,Y cut plates are nearly amorphous, but the surface damage of Z cut does not reach saturation. Radiation damage is mainly due to Nb moving atoms and Ti atoms occupy the interstitial sites. By annealing the sample at 1000℃, most damage is removed from the boundary between implanted layer and LiNbO<sub>3</sub> base to surface.展开更多
Exoelectron is low energy electrons delayed emission from a metallic member surface.The fatigue damage of the metallic often happens under the action of a dynamic load. Theaccumulation of fatigue damage of metallic fr...Exoelectron is low energy electrons delayed emission from a metallic member surface.The fatigue damage of the metallic often happens under the action of a dynamic load. Theaccumulation of fatigue damage of metallic frames leads to the result of surface fatiguemicrocracks. Microcracks would result in the exoelectrons emission. In this paper therelationship between exoelectrons emission and the fatigue damage microcracks of metallicframes is studied. A new type of the Double Grid Air Counter (DGAC) was designed.Experiments have shown that the systems of the DGAC are sound and work efficiently, and themeasurement precision was important, and valuable in study and detection of formation andgrowth of microcracks of the metallic members surface in the initial stage offatigue da,nage.展开更多
There is a problem of real-time detection difficulty in road surface damage detection. This paper proposes an improved lightweight model based on you only look once version 5(YOLOv5). Firstly, this paper fully utilize...There is a problem of real-time detection difficulty in road surface damage detection. This paper proposes an improved lightweight model based on you only look once version 5(YOLOv5). Firstly, this paper fully utilized the convolutional neural network(CNN) + ghosting bottleneck(G_bneck) architecture to reduce redundant feature maps. Afterwards, we upgraded the original upsampling algorithm to content-aware reassembly of features(CARAFE) and increased the receptive field. Finally, we replaced the spatial pyramid pooling fast(SPPF) module with the basic receptive field block(Basic RFB) pooling module and added dilated convolution. After comparative experiments, we can see that the number of parameters and model size of the improved algorithm in this paper have been reduced by nearly half compared to the YOLOv5s. The frame rate per second(FPS) has been increased by 3.25 times. The mean average precision(m AP@0.5: 0.95) has increased by 8%—17% compared to other lightweight algorithms.展开更多
The change in surface damage/microstructures and its effects on the hydrogen(H)isotope/helium(He)dynamic behavior are the key factors for investigating issues of tungsten(W)-based plasma-facing materials(PFMs)in fusio...The change in surface damage/microstructures and its effects on the hydrogen(H)isotope/helium(He)dynamic behavior are the key factors for investigating issues of tungsten(W)-based plasma-facing materials(PFMs)in fusion such as surface erosion,H/He retention and tritium(T)inventory.Complex surface damage/microstructures are introduced in W by high-temperature plasma irradiation and new material design,typically including pre-damage and multi-ion co-deposition induced structures,solute elements and related composites,native defects like dislocations and interfaces,and nanostructures.Systematic experimental and theoretical researches were performed on H isotope/He retention in complex W-based materials in the past decades.In this review,we aim to provide an overview of typical surface damage/microstructures and their effects on H/He retention in W,both in the experiment and multiscale modeling.The distribution/state,dynamics evolution,and interaction with defects/microstructures of H/He are generally summarized at different scales.Finally,the current difficulties,challenges and future directions are also discussed about H/He retention in complex W-based PFMs.展开更多
Deuterated potassium dihydrogen phosphate damage performance at 351 nm is studied on a large-aperture laser system. Bulk and rear-surface damage are initiated under the 3ω fluences of 6.T J/cm2 and 33/cm2, and show d...Deuterated potassium dihydrogen phosphate damage performance at 351 nm is studied on a large-aperture laser system. Bulk and rear-surface damage are initiated under the 3ω fluences of 6.T J/cm2 and 33/cm2, and show different growth characteristics under multiple laser irradiations with the fluence of 6 J/cm2. The size and number of bulk damage keep unchanged once initiated. However, surface damage size also does not grow, while surface damage number increases linearly with laser shots. Different damage thresholds and growth behaviors suggest different formations of bulk and surface damage precursors. The cause of surface damage is supposed to be near-surface absorbing particles buried under the sol-gel coating.展开更多
A mesoscale convective system(MCS) occurred over the East China coastal provinces and the East China Sea on 30April 2021, producing damaging surface winds near the coastal city Nantong with observed speeds reaching 45...A mesoscale convective system(MCS) occurred over the East China coastal provinces and the East China Sea on 30April 2021, producing damaging surface winds near the coastal city Nantong with observed speeds reaching 45 m s^(–1). A simulation using the Weather Research and Forecasting model with a 1.5-km grid spacing generally reproduces the development and subsequent organization of this convective system into an MCS, with an eastward protruding bow segment over the sea. In the simulation, an east-west-oriented high wind swath is generated behind the gust front of the MCS. Descending dry rear-to-front inflows behind the bow and trailing gust front are found to feed the downdrafts in the main precipitation regions. The inflows help to establish spreading cold outflows and enhance the downdrafts through evaporative cooling. Meanwhile, front-to-rear inflows from the south are present, associated with severely rearward-tilted updrafts initially forming over the gust front. Such inflows descend behind(north of) the gust front, significantly enhancing downdrafts and near-surface winds within the cold pool. Consistently, calculated trajectories show that these parcels that contribute to the derecho originate primarily from the region ahead(south) of the east-west-oriented gust front, and dry southwesterly flows in the low-to-middle levels contribute to strong downdrafts within the MCS. Moreover, momentum budget analyses reveal that a large westward-directed horizontal pressure gradient force within the simulated cold pool produced rapid flow acceleration towards Nantong. The analyses enrich the understanding of damaging wind characteristics over coastal East China and will prove helpful to operational forecasters.展开更多
Despite numerous research investigations to understand the influences of various structural parameters,to the authors'knowledge,no research has been the effect of different angles of incidence on stab response and...Despite numerous research investigations to understand the influences of various structural parameters,to the authors'knowledge,no research has been the effect of different angles of incidence on stab response and performance of different types of protective textiles.Three distinct structures of 3D woven textiles and 2D plain weave fabric made with similar high-performance fiber and areal density were designed and manufactured to be tested.Two samples,one composed of a single and the other of 4-panel layers,from each fabric type structure,were prepared,and tested against stabbing at[0○],[22.5○],and[45○]angle of incidence.A new stabbing experimental setup that entertained testing of the specimens at various angles of incidence was engineered and utilized.The stabbing bench is also equipped with magnetic sensors and a UK Home Office Scientific Development Branch(HOSDB)/P1/B sharpness engineered knives to measure the impact velocity and exerted impact energy respectively.A silicon compound was utilized to imprint the Back Face Signature(BFS)on the backing material after every specimen test.Each silicon print was then scanned,digitized,and precisely measured to evaluate the stab response and performance of the specimen based on different performance variables,including Depth of Trauma(DOT),Depth of Penetration(DOP),and Length of Penetration(LOP).Besides,the post-impact surface failure modes of the fabrics were also measured using Image software and analyzed at the microscale level.The results show stab angle of incidence greatly influences the stab response and performance of protective textiles.The outcome of the study could provide not only valuable insights into understanding the stab response and capabilities of protective textiles under different angle of incidence,but also provide valuable information for protective textile manufacturer,armor developer and stab testing and standardizing organizations to consider the angle of incidence while developing,testing,optimizing,and using protective textiles in various applications.展开更多
There are several fatigue-based approaches that estimate the evolution of rolling contact fatigue(RCF) on rails over time and built to be used in tandem with multibody simulations of vehicle dynamics. However, most of...There are several fatigue-based approaches that estimate the evolution of rolling contact fatigue(RCF) on rails over time and built to be used in tandem with multibody simulations of vehicle dynamics. However, most of the models are not directly comparable with each other since they are based on different physical models even though they shall predict the same RCF damage at the end.This article studies different approaches to quantifying RCF and puts forward a measure for the degree of agreement between them. The methodological framework studies various steps in the RCF quantification procedure within the context of one another, identifies the ‘primary quantification step’ in each approach and compares results of the fatigue analyses. In addition to this, two quantities—‘similarity’ and ‘correlation’—have been put forward to give an indication of mutual agreement between models.Four widely used surface-based and sub-surface-based fatigue quantification approaches with varying complexities have been studied. Different operational cases corresponding to a metro vehicle operation in Austria have been considered for this study. Results showed that the best possible quantity to compare is the normalized damage increment per loading cycle coming from different approaches. Amongst the methods studied, approaches that included the load distribution step on the contact patch showed higher similarity and correlation in their results.While the different approaches might qualitatively agree on whether contact cases are ‘damaging’ due to RCF, they might not quantitatively correlate with the trends observed for damage increment values.展开更多
The surface morphology of the continuous SiC filament,prepared by radio frequency heating CVD technique,has been observed and the tensile strength of the filament related to the technological parameters of preparation...The surface morphology of the continuous SiC filament,prepared by radio frequency heating CVD technique,has been observed and the tensile strength of the filament related to the technological parameters of preparation has also been investigated.The tensile strength is found to be dependent directly upon the surface smoothness,grain size and uniformity.How- ever,the CVD temperature,the composition and flow rate of reactive gases,as well as the cleansing of W wire substrate,etc.,are the very important factors.A protective layer coated over the outer surface of SiC filament may effectively improve the smoothness,susceptibility to surface damage and properties of the SiC filament.展开更多
During hard cutting process there is severe thermodynamic coupling effect between cutting tool and workpiece, which causes quenching effect on finished surfaces under certain conditions. However, material phase transf...During hard cutting process there is severe thermodynamic coupling effect between cutting tool and workpiece, which causes quenching effect on finished surfaces under certain conditions. However, material phase transformation mechanism of heat treatment in cutting process is different from the one in traditional process, which leads to changes of the formation mechanism of damaged layer on machined workpiece surface. This paper researches on the generation mechanism of damaged layer on machined surface in the process of PCBN tool hard cutting hardened steel Cr12MoV. Rules of temperature change on machined surface and subsurface are got by means of finite element simulation. In phase transformation temperature experiments rapid transformation instrument is employed, and the effect of quenching under cutting conditions on generation of damaged layer is revealed. Based on that, the phase transformation points of temperature under cutting conditions are determined. By experiment, the effects of cutting speed and tool wear on white layer thickness in damaged layer are revealed. The temperature distribution law of third deformation zone is got by establishing the numerical prediction model, and thickness of white layer in damaged layer is predicted, taking the tool wear effect into consideration. The experimental results show that the model prediction is accurate, and the establishment of prediction model provides a reference for wise selection of parameters in precise hard cutting process. For the machining process with high demanding on surface integrity, the generation of damaged layer on machined surface can be controlled precisely by using the prediction model.展开更多
This study examines the impact of variations in side-blowing airflow velocity on plasma generation,combustion wave propagation mechanisms,and surface damage in fused silica induced by a combined millisecond-nanosecond...This study examines the impact of variations in side-blowing airflow velocity on plasma generation,combustion wave propagation mechanisms,and surface damage in fused silica induced by a combined millisecond-nanosecond pulsed laser.The airflow rate and pulse delay are the main experimental variables.The evolution of plasma motion was recorded using ultrafast time-resolved optical shadowing.The experimental results demonstrate that the expansion velocities of the plasma and combustion wave are influenced differently by the sideblowing airflow at different airflow rates(0.2 Ma,0.4 Ma,and 0.6 Ma).As the flow rate of the sideblow air stream increases,the initial expansion velocities of the plasma and combustion wave gradually decrease,and the side-blow air stream increasingly suppresses the plasma.It is important to note that the target vapor is always formed and ionized into plasma during the combined pulse laser action.Therefore,the side-blown airflow alone cannot completely clear the plasma.Depending on the delay conditions,the pressure of the side-blowing airflow,the influence of inverse Bremsstrahlung radiation absorption and target surface absorption mechanisms can lead to a phenomenon known as the double combustion waves when using a nanosecond pulse laser.Both simulation and experimental results are consistent,indicating the potential for further exploration of fused silica targets in the laser field.展开更多
The irradiation effects of Ar＋, He＋, and S＋ with energy from 10 eV to 180 eV on n-InP（100） surface are analyzed by X-ray photoelectron spectroscopy and low energy electron diffraction. After irradiation on the n-...The irradiation effects of Ar＋, He＋, and S＋ with energy from 10 eV to 180 eV on n-InP（100） surface are analyzed by X-ray photoelectron spectroscopy and low energy electron diffraction. After irradiation on the n-InP surface, damage on the surface, displacement of the Fermilevel and formation of sulfur species on S＋ exposed surface are found and studied. Successive annealing is done to suppress the surface states introduced by S＋ exposure. However, it is unsuccessful in removing the damage caused by noble ions. Besides, S＋ ions can efficiently repair the Ar＋ damaged surface, and finally form a fine 2×2 InP surface.展开更多
The present study shows that naturally developed fracture surfaces in rocks display the properties of self-affine fractals. Surface roughness can be quantitatively characterized by fractal dimension D and the intercep...The present study shows that naturally developed fracture surfaces in rocks display the properties of self-affine fractals. Surface roughness can be quantitatively characterized by fractal dimension D and the intercept A on the log-log plot of variance: the former describes the irregularity and the later is statistically analogues to the slopes of asperities. In order to confirm the effects of these fractalparameters on the properties and mechanical behavior of rock joints, which have been observed in experiments under both normal andshear loadings, a theoretic model of rock joint is proposed on the basis of contact mechanics. The shape of asperity at contact is assumed to have a sinusoidal form in its representative scale r, with fractal dimension D and the intercept A. The model considers different local contact mechanisms, such as elastic deformation, frictional sliding and tensile fracture of the asperity. The empirical evolution law of surface damage developed in experiment is implemented into the model to up-date geometry of asperity in loading history. The effects of surface roughness characterized by D, A and re on normal and shear deformation of rock joint have been elaborated.展开更多
The current collector fracture failure of lithium-ion batteries(LIBs)occurs during its winding production process frequently,and the consequent damages are usually large,but little research has been conducted on this ...The current collector fracture failure of lithium-ion batteries(LIBs)occurs during its winding production process frequently,and the consequent damages are usually large,but little research has been conducted on this phenomenon.This work stems from the difficulty and obstacles in the winding process of actual production of LIBs.The fracture failure of the current collectors is easily caused by the evolution and mutation of the mechanical behavior during the winding process,resulting in safety hazards and poor efficiency.The purpose of this work is to reveal the evolution and distribution mechanism of circumferential strain of the current collectors on the fracture failure under the constraint of winding process.Experimental tests,finite element calculations and theoretical model are used to study the evolution and distribution of circumferential strain.The dynamic evolution process of circumferential strain is tested accurately,and the mechanism of fracture failure of current collectors is revealed.The criterion for current collector strength is proposed based on the results of strain analysis and SEM observation.展开更多
The coiled tubing plugging has become the main means of plugging in gas Wells in Xinjiang. These Wells are deep and have high pressure, which can easily affect the fatigue life of the operating coiled tubing. In order...The coiled tubing plugging has become the main means of plugging in gas Wells in Xinjiang. These Wells are deep and have high pressure, which can easily affect the fatigue life of the operating coiled tubing. In order to improve the life of coiled tubing in high-pressure gas Wells, this paper studies the plugging conditions of coiled tubing in high-pressure ultra-deep Wells. Firstly, the cross section deformation of coiled tubing under high internal pressure is analyzed. Secondly, the factors influencing the fatigue life of coiled tubing and the influence of surface damage on the fatigue life of coiled tubing were studied. Finally, the mechanism of furrow damage caused by coiled tubing and the main measures to reduce furrow damage are analyzed. The following suggestions are made to improve the life of coiled tubing: select the right material and the right size coiled tubing;Use appropriate measures to prevent premature coiled tubing failure and reduce operating costs.展开更多
基金supported by the National Natural Science Foundation of China under grant No. 50605043
文摘Powdering/exfoliating of coatings and scratching galvanized steels and high strength steels （HSS）, are the main forms of surface damage in the forming of which result in increased die maintenance cost and scrap rate. In this study, a special rectangular box was developed to investigate the behavior and characteristics of surface damage in sheet metal forming （SMF） processes. U-channel forming tests were conducted to study the effect of tool hardness on surface damage in the forming of high strength steels and galvanized steels （hot-dip galvanized and galvannealed steels）. Experimental results indicate that sheet deformation mode influences the severity of surface damage in SMF and surface damage occurs easily at the regions where sheet specimen deforms under the action of compressive stress. Die corner is the position where surface damage initiates. For HSS sheet, surface damage is of major interest due to high forming pressure. The HSS and hot-dip galvanized steels show improved ability of damage-resistance with increased hardness of the forming tool. However, for galvannealed steel it is not the forming tool with the highest hardness value that performs best.
基金The University of Nottingham,the Mexican National Council for Science and Technology(CONACYT)EPSRC through the DTP 2018–19 University of Nottingham(Grant No.EP/T517902/1)Nottingham Research Fellowship and University of Nottingham Propulsion Futures Beacon Programme.
文摘Bone cutting is of importance in orthopaedic surgery but is also challenging due to its nature of brittleness—where severe mechanical and thermal damages can be introduced easily in conventional machining.Laser machining is a new technology that can allow for complex cut geometries whilst minimising surface defects i.e.,smearing,which occur in mechanical methods.However,comparative studies on the influence of lasers with different pulse characteristics on necrotic damage and surface integrity have not been reported yet.This paper for the first time investigates the effects of laser type on the necrotic damage and surface integrity in fresh bovine cortical bone after ex-situ laser machining.Three lasers of different pulse widths,i.e.,picosecond,nanosecond and continuous wave lasers have been investigated with different feed speeds tested to study the machining efficiency.The cutting temperature,and geometrical outputs have been measured to investigate the thermal influence on the cooling behaviour of the bone samples while high-speed imaging was used to compare the material removal mechanisms between a pulsed and continuous wave laser.Furthermore,an in-depth histological analysis of the subsurface has revealed that the nanosecond laser caused the largest necrotic depth,owing to the high pulse frequency limiting the dissipation of heat.It has also been observed that surface cracks positioned perpendicular to the trench direction were produced after machining by the picosecond laser,indicative of the photomechanical effect induced by plasma explosions.Therefore,the choice of laser type(i.e.,in terms of its pulse width and frequency)needs to be critically considered for appropriate application during laser osteotomy with minimum damage and improved healing.
文摘Two complementary types NPN and PNP of bipolar junction transistors （BJTs） were exposed to higll dose of neutrons and gamma rays. The change in the base and collector currents, minority carriers lifetime, and current gain factor/3 with respect to the dose were analyzed. The contributions of the base current according to the defect types were also reported. It was declared that the radiation effect of neutrons was almost similar between the two transistor types, this effect at high dose may decrease the value of/3 to less than one. The Messenger-Spratt equation was used to describe the experimental results in this case. However, the experimental data demonstrated that the effect of gamma rays was generally higher on NPN than PNP transistors. This is mainly attributed to the difference in the behavior of the trapped positive charges in the SiO2 layers. Meanwhile, this difference tends to be small for high gamma dose.
文摘The surface damage and the damage depth in wire-cut silicon wafers and inner-diameter (ID) cut silicon wafers were studied by means of thickness meter, scanning electron microscopy (SEM) and double crystal X-ray diffractometer. The results show that the surface of wire-cut silicon wafers is rougher than that of ID-cut silicon wafers and the surface damage in wire-cut silicon wafers is more serious than that in ID-cut silicon wafers, while the damage depth in wire-cut silicon wafers is smaller than that in ID-cut silicon wafers. The possible reasons for the generation of surface damage in wire-cut silicon wafers were also discussed.
基金supported by the Beijing Natural Science Foundation (KZ200810005001)the National Basic Research Program of China (973 Program) (2010CB732104)
文摘This letter reports experimental observation of a direct correlation between the acoustic nonlinearity parameter (NP) measured with nonlinear Rayleigh waves and the accumulation of plasticity damage in an AZ31 magnesium alloy plate specimen.Rayleigh waves are generated and detected with wedge transducers,and the NPs are measured at different stress levels.The results show that there is a significant increase in the NPs with monotonic tensile loads surpassing the material’s yielding stress.The research suggests an effective nondestructive evaluation method to track the surface damage in metals.
文摘In this paper, damages and annealing effects of X,Y and Z cut LiNbO-3 implanted by 350keV high energy Ti (1.5 x 10<sup>17</sup> / cm<sup>2</sup>) are studied. The surface damages of X,Y cut plates are nearly amorphous, but the surface damage of Z cut does not reach saturation. Radiation damage is mainly due to Nb moving atoms and Ti atoms occupy the interstitial sites. By annealing the sample at 1000℃, most damage is removed from the boundary between implanted layer and LiNbO<sub>3</sub> base to surface.
文摘Exoelectron is low energy electrons delayed emission from a metallic member surface.The fatigue damage of the metallic often happens under the action of a dynamic load. Theaccumulation of fatigue damage of metallic frames leads to the result of surface fatiguemicrocracks. Microcracks would result in the exoelectrons emission. In this paper therelationship between exoelectrons emission and the fatigue damage microcracks of metallicframes is studied. A new type of the Double Grid Air Counter (DGAC) was designed.Experiments have shown that the systems of the DGAC are sound and work efficiently, and themeasurement precision was important, and valuable in study and detection of formation andgrowth of microcracks of the metallic members surface in the initial stage offatigue da,nage.
基金supported by the Shanghai Sailing Program,China (No.20YF1447600)the Research Start-Up Project of Shanghai Institute of Technology (No.YJ2021-60)+1 种基金the Collaborative Innovation Project of Shanghai Institute of Technology (No.XTCX2020-12)the Science and Technology Talent Development Fund for Young and Middle-Aged Teachers at Shanghai Institute of Technology (No.ZQ2022-6)。
文摘There is a problem of real-time detection difficulty in road surface damage detection. This paper proposes an improved lightweight model based on you only look once version 5(YOLOv5). Firstly, this paper fully utilized the convolutional neural network(CNN) + ghosting bottleneck(G_bneck) architecture to reduce redundant feature maps. Afterwards, we upgraded the original upsampling algorithm to content-aware reassembly of features(CARAFE) and increased the receptive field. Finally, we replaced the spatial pyramid pooling fast(SPPF) module with the basic receptive field block(Basic RFB) pooling module and added dilated convolution. After comparative experiments, we can see that the number of parameters and model size of the improved algorithm in this paper have been reduced by nearly half compared to the YOLOv5s. The frame rate per second(FPS) has been increased by 3.25 times. The mean average precision(m AP@0.5: 0.95) has increased by 8%—17% compared to other lightweight algorithms.
基金This work was financially supported by the National Natural Science Foundation of China(Grant Nos.11975018,11775254 and 11534012)the National Magnetic Confinement Fusion Energy Research Project(Grant No.2018YEF0308100)+2 种基金the Science Challenge Project(Grant No.TZ2018004)the Youth Innovation Promotion Association of Chinese Academy of Sciences(CAS)(Grant No.2016386)Director Grants of Hefei Institutes of Physics Science,Chinese Academy of Sciences(CASHIPS).
文摘The change in surface damage/microstructures and its effects on the hydrogen(H)isotope/helium(He)dynamic behavior are the key factors for investigating issues of tungsten(W)-based plasma-facing materials(PFMs)in fusion such as surface erosion,H/He retention and tritium(T)inventory.Complex surface damage/microstructures are introduced in W by high-temperature plasma irradiation and new material design,typically including pre-damage and multi-ion co-deposition induced structures,solute elements and related composites,native defects like dislocations and interfaces,and nanostructures.Systematic experimental and theoretical researches were performed on H isotope/He retention in complex W-based materials in the past decades.In this review,we aim to provide an overview of typical surface damage/microstructures and their effects on H/He retention in W,both in the experiment and multiscale modeling.The distribution/state,dynamics evolution,and interaction with defects/microstructures of H/He are generally summarized at different scales.Finally,the current difficulties,challenges and future directions are also discussed about H/He retention in complex W-based PFMs.
基金Supported by the National Natural Science Foundation of China under Grant No 61505187
文摘Deuterated potassium dihydrogen phosphate damage performance at 351 nm is studied on a large-aperture laser system. Bulk and rear-surface damage are initiated under the 3ω fluences of 6.T J/cm2 and 33/cm2, and show different growth characteristics under multiple laser irradiations with the fluence of 6 J/cm2. The size and number of bulk damage keep unchanged once initiated. However, surface damage size also does not grow, while surface damage number increases linearly with laser shots. Different damage thresholds and growth behaviors suggest different formations of bulk and surface damage precursors. The cause of surface damage is supposed to be near-surface absorbing particles buried under the sol-gel coating.
基金primarily supported by the Ministry of Science and Technology of the People's Republic of China (MOST)(Grant No. 2018YFC1507303)National Natural Science Foundation of China (Grant Nos. 419505044,41941007, and 42230607)+1 种基金by the Talent Research Start-Up Fund of Nanjing University of Aeronautics and Astronautics(Grant No. 1007-90YAH22046)supported by The High Performance Computing Platform of Nanjing University of Aeronautics and Astronautics。
文摘A mesoscale convective system(MCS) occurred over the East China coastal provinces and the East China Sea on 30April 2021, producing damaging surface winds near the coastal city Nantong with observed speeds reaching 45 m s^(–1). A simulation using the Weather Research and Forecasting model with a 1.5-km grid spacing generally reproduces the development and subsequent organization of this convective system into an MCS, with an eastward protruding bow segment over the sea. In the simulation, an east-west-oriented high wind swath is generated behind the gust front of the MCS. Descending dry rear-to-front inflows behind the bow and trailing gust front are found to feed the downdrafts in the main precipitation regions. The inflows help to establish spreading cold outflows and enhance the downdrafts through evaporative cooling. Meanwhile, front-to-rear inflows from the south are present, associated with severely rearward-tilted updrafts initially forming over the gust front. Such inflows descend behind(north of) the gust front, significantly enhancing downdrafts and near-surface winds within the cold pool. Consistently, calculated trajectories show that these parcels that contribute to the derecho originate primarily from the region ahead(south) of the east-west-oriented gust front, and dry southwesterly flows in the low-to-middle levels contribute to strong downdrafts within the MCS. Moreover, momentum budget analyses reveal that a large westward-directed horizontal pressure gradient force within the simulated cold pool produced rapid flow acceleration towards Nantong. The analyses enrich the understanding of damaging wind characteristics over coastal East China and will prove helpful to operational forecasters.
文摘Despite numerous research investigations to understand the influences of various structural parameters,to the authors'knowledge,no research has been the effect of different angles of incidence on stab response and performance of different types of protective textiles.Three distinct structures of 3D woven textiles and 2D plain weave fabric made with similar high-performance fiber and areal density were designed and manufactured to be tested.Two samples,one composed of a single and the other of 4-panel layers,from each fabric type structure,were prepared,and tested against stabbing at[0○],[22.5○],and[45○]angle of incidence.A new stabbing experimental setup that entertained testing of the specimens at various angles of incidence was engineered and utilized.The stabbing bench is also equipped with magnetic sensors and a UK Home Office Scientific Development Branch(HOSDB)/P1/B sharpness engineered knives to measure the impact velocity and exerted impact energy respectively.A silicon compound was utilized to imprint the Back Face Signature(BFS)on the backing material after every specimen test.Each silicon print was then scanned,digitized,and precisely measured to evaluate the stab response and performance of the specimen based on different performance variables,including Depth of Trauma(DOT),Depth of Penetration(DOP),and Length of Penetration(LOP).Besides,the post-impact surface failure modes of the fabrics were also measured using Image software and analyzed at the microscale level.The results show stab angle of incidence greatly influences the stab response and performance of protective textiles.The outcome of the study could provide not only valuable insights into understanding the stab response and capabilities of protective textiles under different angle of incidence,but also provide valuable information for protective textile manufacturer,armor developer and stab testing and standardizing organizations to consider the angle of incidence while developing,testing,optimizing,and using protective textiles in various applications.
基金funding from the Shift2Rail Joint Undertaking (JU) under the European Union’s Horizon 2020 research and innovation programme under grant agreement (No. 826206)。
文摘There are several fatigue-based approaches that estimate the evolution of rolling contact fatigue(RCF) on rails over time and built to be used in tandem with multibody simulations of vehicle dynamics. However, most of the models are not directly comparable with each other since they are based on different physical models even though they shall predict the same RCF damage at the end.This article studies different approaches to quantifying RCF and puts forward a measure for the degree of agreement between them. The methodological framework studies various steps in the RCF quantification procedure within the context of one another, identifies the ‘primary quantification step’ in each approach and compares results of the fatigue analyses. In addition to this, two quantities—‘similarity’ and ‘correlation’—have been put forward to give an indication of mutual agreement between models.Four widely used surface-based and sub-surface-based fatigue quantification approaches with varying complexities have been studied. Different operational cases corresponding to a metro vehicle operation in Austria have been considered for this study. Results showed that the best possible quantity to compare is the normalized damage increment per loading cycle coming from different approaches. Amongst the methods studied, approaches that included the load distribution step on the contact patch showed higher similarity and correlation in their results.While the different approaches might qualitatively agree on whether contact cases are ‘damaging’ due to RCF, they might not quantitatively correlate with the trends observed for damage increment values.
文摘The surface morphology of the continuous SiC filament,prepared by radio frequency heating CVD technique,has been observed and the tensile strength of the filament related to the technological parameters of preparation has also been investigated.The tensile strength is found to be dependent directly upon the surface smoothness,grain size and uniformity.How- ever,the CVD temperature,the composition and flow rate of reactive gases,as well as the cleansing of W wire substrate,etc.,are the very important factors.A protective layer coated over the outer surface of SiC filament may effectively improve the smoothness,susceptibility to surface damage and properties of the SiC filament.
基金Supported by National Natural Science Foundation of China (Grant Nos.51105119,51235003)
文摘During hard cutting process there is severe thermodynamic coupling effect between cutting tool and workpiece, which causes quenching effect on finished surfaces under certain conditions. However, material phase transformation mechanism of heat treatment in cutting process is different from the one in traditional process, which leads to changes of the formation mechanism of damaged layer on machined workpiece surface. This paper researches on the generation mechanism of damaged layer on machined surface in the process of PCBN tool hard cutting hardened steel Cr12MoV. Rules of temperature change on machined surface and subsurface are got by means of finite element simulation. In phase transformation temperature experiments rapid transformation instrument is employed, and the effect of quenching under cutting conditions on generation of damaged layer is revealed. Based on that, the phase transformation points of temperature under cutting conditions are determined. By experiment, the effects of cutting speed and tool wear on white layer thickness in damaged layer are revealed. The temperature distribution law of third deformation zone is got by establishing the numerical prediction model, and thickness of white layer in damaged layer is predicted, taking the tool wear effect into consideration. The experimental results show that the model prediction is accurate, and the establishment of prediction model provides a reference for wise selection of parameters in precise hard cutting process. For the machining process with high demanding on surface integrity, the generation of damaged layer on machined surface can be controlled precisely by using the prediction model.
基金funded by the International Science and Technology Cooperation Project of Jilin Provincial Department of Science and Technology(No.20230402078GH)。
文摘This study examines the impact of variations in side-blowing airflow velocity on plasma generation,combustion wave propagation mechanisms,and surface damage in fused silica induced by a combined millisecond-nanosecond pulsed laser.The airflow rate and pulse delay are the main experimental variables.The evolution of plasma motion was recorded using ultrafast time-resolved optical shadowing.The experimental results demonstrate that the expansion velocities of the plasma and combustion wave are influenced differently by the sideblowing airflow at different airflow rates(0.2 Ma,0.4 Ma,and 0.6 Ma).As the flow rate of the sideblow air stream increases,the initial expansion velocities of the plasma and combustion wave gradually decrease,and the side-blow air stream increasingly suppresses the plasma.It is important to note that the target vapor is always formed and ionized into plasma during the combined pulse laser action.Therefore,the side-blown airflow alone cannot completely clear the plasma.Depending on the delay conditions,the pressure of the side-blowing airflow,the influence of inverse Bremsstrahlung radiation absorption and target surface absorption mechanisms can lead to a phenomenon known as the double combustion waves when using a nanosecond pulse laser.Both simulation and experimental results are consistent,indicating the potential for further exploration of fused silica targets in the laser field.
基金ACKNOWLEDGMENTS This work was supported by the National Natural Science Foundation of China （No.11275024） and the Ministry of Science and Technology of China （No.2013YQ03059503 and No.2011AA120101）. The authors would like to thank Prof. R. W. M. Kwok from the Chinese University of Hong Kong.
文摘The irradiation effects of Ar＋, He＋, and S＋ with energy from 10 eV to 180 eV on n-InP（100） surface are analyzed by X-ray photoelectron spectroscopy and low energy electron diffraction. After irradiation on the n-InP surface, damage on the surface, displacement of the Fermilevel and formation of sulfur species on S＋ exposed surface are found and studied. Successive annealing is done to suppress the surface states introduced by S＋ exposure. However, it is unsuccessful in removing the damage caused by noble ions. Besides, S＋ ions can efficiently repair the Ar＋ damaged surface, and finally form a fine 2×2 InP surface.
文摘The present study shows that naturally developed fracture surfaces in rocks display the properties of self-affine fractals. Surface roughness can be quantitatively characterized by fractal dimension D and the intercept A on the log-log plot of variance: the former describes the irregularity and the later is statistically analogues to the slopes of asperities. In order to confirm the effects of these fractalparameters on the properties and mechanical behavior of rock joints, which have been observed in experiments under both normal andshear loadings, a theoretic model of rock joint is proposed on the basis of contact mechanics. The shape of asperity at contact is assumed to have a sinusoidal form in its representative scale r, with fractal dimension D and the intercept A. The model considers different local contact mechanisms, such as elastic deformation, frictional sliding and tensile fracture of the asperity. The empirical evolution law of surface damage developed in experiment is implemented into the model to up-date geometry of asperity in loading history. The effects of surface roughness characterized by D, A and re on normal and shear deformation of rock joint have been elaborated.
基金National Natural Science Foundation of China(12002183)Postdoctoral Science Foundation(2019TQ0171,2020M670304)Beijing Natural Science Foundation(Grant Nos.16L00001 and 2182065)are Rratefullv acknowledged.
文摘The current collector fracture failure of lithium-ion batteries(LIBs)occurs during its winding production process frequently,and the consequent damages are usually large,but little research has been conducted on this phenomenon.This work stems from the difficulty and obstacles in the winding process of actual production of LIBs.The fracture failure of the current collectors is easily caused by the evolution and mutation of the mechanical behavior during the winding process,resulting in safety hazards and poor efficiency.The purpose of this work is to reveal the evolution and distribution mechanism of circumferential strain of the current collectors on the fracture failure under the constraint of winding process.Experimental tests,finite element calculations and theoretical model are used to study the evolution and distribution of circumferential strain.The dynamic evolution process of circumferential strain is tested accurately,and the mechanism of fracture failure of current collectors is revealed.The criterion for current collector strength is proposed based on the results of strain analysis and SEM observation.
文摘The coiled tubing plugging has become the main means of plugging in gas Wells in Xinjiang. These Wells are deep and have high pressure, which can easily affect the fatigue life of the operating coiled tubing. In order to improve the life of coiled tubing in high-pressure gas Wells, this paper studies the plugging conditions of coiled tubing in high-pressure ultra-deep Wells. Firstly, the cross section deformation of coiled tubing under high internal pressure is analyzed. Secondly, the factors influencing the fatigue life of coiled tubing and the influence of surface damage on the fatigue life of coiled tubing were studied. Finally, the mechanism of furrow damage caused by coiled tubing and the main measures to reduce furrow damage are analyzed. The following suggestions are made to improve the life of coiled tubing: select the right material and the right size coiled tubing;Use appropriate measures to prevent premature coiled tubing failure and reduce operating costs.
