In this work,the influences of surface layer slurry at different temperatures(10℃,14℃,18℃,22℃)on wax patterns deformation,shrinkage,slurry coating characteristics,and the surface quality of the casting were invest...In this work,the influences of surface layer slurry at different temperatures(10℃,14℃,18℃,22℃)on wax patterns deformation,shrinkage,slurry coating characteristics,and the surface quality of the casting were investigated by using a single factor variable method.The surface morphologies of the shell molds produced by different temperatures of the surface(first)layer slurries were observed via electron microscopy.Furthermore,the microscopic composition of these shell molds was obtained by EDS,and the osmotic effect of the slurry on the wax patterns at different temperatures was also assessed by the PZ-200 Contact Angle detector.The forming reasons for the surface cracks and holes of thick and large ZTC4 titanium alloy by investment casting were analyzed.The experimental results show that the surface of the shell molds prepared by the surface layer slurry with a low temperature exhibits noticeable damage,which is mainly due to the poor coating performance and the serious expansion and contraction of wax pattern at low temperatures.The second layer shell material(SiO_(2),Al_(2)O_(3))immerses into the crack area of the surface layer,contacts and reacts with the molten titanium to form surface cracks and holes in the castings.With the increase of the temperature of surface layer slurry,the damage to the shell surface tends to weaken,and the composition of the shell molds'surface becomes more uniform with less impurities.The results show that the surface layer slurry at 22℃is evenly coated on the surface of the wax patterns with appropriate thickness,and there is no surface shell mold rupture caused by sliding slurry after sand leaching.The surface layer slurry temperature is consistent with the wax pattern temperature and the workshop temperature,so there is no damage of the surface layer shell caused by expansion and contraction.Therefore,the shell mold prepared by the surface layer slurry at this temperature has good integrity,isolating the contact between the low inert shell material and the titanium liquid effectively,and the ZTC4 titanium alloy cylinder casting prepared by this shell mold is smooth,without cracks and holes.展开更多
In hilly regions,the existence of surface cracks in rock mass induces a potential threat to structural stability.Thus,the present research aims to explore the impact of surface cracks on the loadbearing capacity of st...In hilly regions,the existence of surface cracks in rock mass induces a potential threat to structural stability.Thus,the present research aims to explore the impact of surface cracks on the loadbearing capacity of strip footing placed on the rock mass.By taking into account the various boundary constraints across the surface of crack edges,the study investigates the presence of two categories of surface cracks,namely(1)separated crack,and(2)fine crack.The lower bound limit analysis is employed in conjunction with the finite element method(LBFELA)to conduct the numerical analysis.In order to evaluate rock mass yielding,the power conic programming(PCP)method is utilized to implement the generalized Hoek-Brown(GHB)failure criterion.The stability of the strip footing is analyzed by determining the bearing capacity factor(Nσγ),which is presented in the form of design charts by varying the strength parameters of rock,including the Geological Strength Index(GSI),Hoek-Brown material parameter(mi),Disturbance factor(D),and Normalised Uniaxial Compressive Strength(σci/γB),whereγis the unit weight of rock mass,and B is the width of strip footing.The study also investigates the impact of cracks on strip footings,considering different positions of the crack(LC)and depths of the crack(DC).The results demonstrate that the influence of the fine crack is only noticeable until the LC/B ratio reaches 6.However,for the separated crack,its impact remains significant even when the LC/B ratio exceeds 16.The appearance of fine crack at the edge of the footing results in a decrease in the magnitude Nσγof up to 45%,indicating a substantial reduction in the stability of the footing.The failure patterns are presented and discussed in detail for various cases in this study to examine the effect of surface cracks on the strip footing and to address the extent of the plastic collapse.展开更多
In order to ensure safe mining and reduce surface damage in shallow multi-seam mining,the failure characteristics of interburden strata with different coal pillars offset distances between pillars in the upper and low...In order to ensure safe mining and reduce surface damage in shallow multi-seam mining,the failure characteristics of interburden strata with different coal pillars offset distances between pillars in the upper and lower seams,the distribution characteristics of stress concentration in coal pillars,and the development characteristics of stratum cracks and subsidence were investigated by physical and UDEC2D simulation.Meanwhile,the effect of different coal pillar offset distances on stress concentration of coal pillar and development of stratum cracks were studied.Based on those results,a formula for safe mining and reducing surface damage was established,which provided a theoretical basis for safe and environmentally friendly mining in shallow multi-seam.According to the results,the optimal coal pillar offset distance(the side to side horizontal distance of the upper and lower coal pillars)between the upper and lower coal seams was developed to reduce the stress concentration of coal pillars and surface damage.The results of this study have been applied in Ningtiaota coal mine and have achieved good results in safe and environmentally friendly mining.展开更多
Static tensile test and tensile-tensile fatigue test of medium carbon steel sheet specimens with surface crack precut were performed on MTS810 hydraulic testing machine to clear the meaning of the point of Hp(y) value...Static tensile test and tensile-tensile fatigue test of medium carbon steel sheet specimens with surface crack precut were performed on MTS810 hydraulic testing machine to clear the meaning of the point of Hp(y) value zero. Magnetic memory signals were measured during the test process. The results show that only one point of Hp(y) zero value exists in all measured magnetic signal curves during the loading process, which should be a sign of intersection of positive-negative magnetic poles after magnetic ordered state appears and does not indicate the position of surface crack precut. The analysis shows that the surface crack precut can not interrupt the magnetic ordered state occurred during the test completely, hence its Hp(y) value is not zero. However, the crack extending to a penetrated defect at the instant of specimen′s fracture leads to the discontinuance of magnetic ordered state.展开更多
The effect of alloy segregation and delta （δ） ferrite contents on surface cracking of three standard （i.e. AISI 304L, AISI 310S and AISI 321） and two low nickel （i.e. LNi-1 and LNi-0.3） austenitic stainless ste...The effect of alloy segregation and delta （δ） ferrite contents on surface cracking of three standard （i.e. AISI 304L, AISI 310S and AISI 321） and two low nickel （i.e. LNi-1 and LNi-0.3） austenitic stainless steels （ASS） during hot roiling was investigated using optical microscopy （OM）, automatic image analyzer, scanning electron microscopy （SEM）, energy dispersive X-ray spectroscopy （EDX） and electron probe micro analyzer （EPMA）. It was observed that the amount of 6-ferrite varied among different grades and also distributed heterogeneously across the width of the steel plates. In general, low nickel ASS showed higher amount of 6-ferrite compared to the standard ASS grades. The tendency to surface cracking during hot rolling gradually increased with increasing 6-ferrite content. Interestingly, carbon and nitrogen exerted maximum effect on 6-ferrite formation. The higher carbon and nitrogen content in the steel decreased 6-ferMte content. In addition, the segregation of Cu and Mn plays significant role in low nickel ASS and Ni-Cr in case of standard ASS has profound effect on surface cracking of the steel plates. A possible cause of surface crack formation/origination in steel plates during hot rolling was discussed.展开更多
A theoretical model of semi-elliptic surface crack growth based on the low cycle strain damage accumulation near the crack tip along the cracking direction and the Newman-Raju formula is developed. The crack is regard...A theoretical model of semi-elliptic surface crack growth based on the low cycle strain damage accumulation near the crack tip along the cracking direction and the Newman-Raju formula is developed. The crack is regarded as a sharp notch with a small curvature radius and the process zone is assumed to be the size of cyclic plastic zone. The modified Hutchinson, Rice and Rosengren （HRR） formulations are used in the presented study. Assuming that the shape of surface crack front is controlled by two critical points： the deepest point and the surface point. The theoretical model is applied to semi-elliptic surface cracked A1 7075-T6 alloy plate under cyclic loading, and five different initial crack shapes are discussed in present study. Good agreement between experimental and theoretical results is obtained.展开更多
18Mn18Cr0.5N steel specimens were preheated at the temperatures from 1100 to 1250°C for 5 min,and then cooled to 950°C and compressed.The cracking behaviors were investigated using optical microscopy and sca...18Mn18Cr0.5N steel specimens were preheated at the temperatures from 1100 to 1250°C for 5 min,and then cooled to 950°C and compressed.The cracking behaviors were investigated using optical microscopy and scanning electron microscopy.The results showed that the hot workability of 18Mn18Cr0.5N steel gradually decreased with increasing preheating temperature between 1100 and 1200°C,and quickly deteriorated up to 1250°C.Above 1200°C,delta ferrite particles appeared in 18Mn18Cr0.5N steel,promoted cavity coalescence on grain boundary,and accelerated surface crack formation during the hot working process.展开更多
Based on the production practice of medium carbon thin slabs in the CSP plant,the reasons and influencing factors for the formation of longitudinal cracks were investigated,and some industrial measures were taken to e...Based on the production practice of medium carbon thin slabs in the CSP plant,the reasons and influencing factors for the formation of longitudinal cracks were investigated,and some industrial measures were taken to eliminate the cracks.The results show that the efficient solutions to reduce longitudinal cracks are improving the performance of the mold powder,stabilizing the mold heat flux,and maintaining a proper taper of the mold during casting.Proper pouring temperature and secondary cooling also play important roles in preventing longitudinal surface cracks.展开更多
Three-dimensional crack closure correction methods are investigated in this paper.The fatigue crack growth tests of surface cracks in 14MnNbq steel for bridge plate subjected to tensile and bending loadings are system...Three-dimensional crack closure correction methods are investigated in this paper.The fatigue crack growth tests of surface cracks in 14MnNbq steel for bridge plate subjected to tensile and bending loadings are systematically conducted.The experimentally measured fatigue crack growth rates of surface cracks are compared with those of through-thickness cracks in detail.It is found that the crack growth rates of surface cracks are lower than those of through-thickness cracks.In order to correct their differences in fatigue crack growth rates, a dimensionless crack closure correction model is proposed.Although this correction model is determined only by the experimental data of surface cracks under tensile loading with a constant ratio R=0.05, it can correlate the surface crack growth rates with reasonable accuracy under tensile and bending loadings with various stress ratios ranging from 0 to 0.5.Furthermore, predictions of fatigue life and crack aspect ratio for surface cracks are discussed, and the predicted results are also compared with those obtained from other prediction approaches.Comparison results show that the proposed crack closure correction model gives better prediction of fatigue life than other models.展开更多
In this paper, simulated experiment device of coal and gas outburst was employed to perform the experiment on gas-containing coal extrusion. In the experiment, coal surface cracks were observed with a high-speed camer...In this paper, simulated experiment device of coal and gas outburst was employed to perform the experiment on gas-containing coal extrusion. In the experiment, coal surface cracks were observed with a high-speed camera and then the images were processed by sketch. Based on the above description, the paper studied the fractal dimension values from different positions of coal surface as well as their changing laws with time. The results show that there is a growing parabola trend of crack dimension value in the process of coal extrusion. Accordingly, we drew the conclusion that extruded coal crack evolution is a process of fractal dimension value increase. On the basis of fractal dimension values taken from different parts of coal masses, a fractal dimension of the contour map was drawn. Thus, it is clear that the contour map involves different crack fractal dimension values from different positions. To be specific, where there are complicated force and violent movement in coal mass, there are higher fractal dimension values, i.e., the further the middle of observation surface is from the exit of coal mass, and the lower the fractal dimension value is. In line with fractal geometry and energy theory of coal and gas outburst, this study presents the relation between fractal dimension and energy in the process of extruding. In conclusion, the evolution of crack fractal dimension value can signify that of energy, which has laid a solid foundation for the quantification research on the mechanism of gas-containing coal extrusion.展开更多
In this paper, a modified shear-lag model is developed to calculate the surface crack density in thermal barrier coatings（TBCs）. The mechanical properties of TBCs are also measured to quantitatively assess their sur...In this paper, a modified shear-lag model is developed to calculate the surface crack density in thermal barrier coatings（TBCs）. The mechanical properties of TBCs are also measured to quantitatively assess their surface crack density. Acoustic emission（AE） and digital image correlation methods are applied to monitor the surface cracking in TBCs under tensile loading. The results show that the calculated surface crack density from the modified model is in agreement with that obtained from experiments. The surface cracking process of TBCs can be discriminated by their AE characteristics and strain evolution. Based on the correlation of energy released from cracking and its corresponding AE signals, a linear relationship is built up between the surface crack density and AE parameters, with the slope being dependent on the mechanical properties of TBCs.展开更多
To avoid leaking or bursing by crack on surface of preddure vessels made of streels,a method for analyzing the principle of propagation of a surface crack is established,and used on a spherical vessel with program cal...To avoid leaking or bursing by crack on surface of preddure vessels made of streels,a method for analyzing the principle of propagation of a surface crack is established,and used on a spherical vessel with program calculation and simulation,the program is written in QBASIC and the reaults are provided and discussed.展开更多
The Monte- Carlo method is used to simulate the surface fatigue crack growth rate for offshore structural steel E36-Z35, and to determine the distributions and relevance of the parameters in the Paris equation. By thi...The Monte- Carlo method is used to simulate the surface fatigue crack growth rate for offshore structural steel E36-Z35, and to determine the distributions and relevance of the parameters in the Paris equation. By this method, the time and cost of fatigue crack propagation testing can be reduced. The application of the method is demonstrated by use of four sets of fatigue crack propagation data for offshore structural steel E36-Z35. A comparison of the test data with the theoretical prediction for surface crack growth rate shows the application of the simulation method to the fatigue crack propagation tests is successful.展开更多
In this paper a semi-elliptic surface crack problem in an elastic solid of finite size under impact loading is investigated. An analysis is performed by means of fracture dynamics and the finite element method, and a ...In this paper a semi-elliptic surface crack problem in an elastic solid of finite size under impact loading is investigated. An analysis is performed by means of fracture dynamics and the finite element method, and a three-dimensional finite element program is developed to compute the dynamic stress intensity factor. The results reveal that the effects of the solid＇s boundary surface, crack surface, material inertia and stress wave interactions play significant roles in dynamic fracture.展开更多
The fact that the amount of the mold flux components differs at differentlocations on the cracking surface indicates that the longitudinal surface cracks are initiallyformed in the mold and are enlarged in the seconda...The fact that the amount of the mold flux components differs at differentlocations on the cracking surface indicates that the longitudinal surface cracks are initiallyformed in the mold and are enlarged in the secondary cooling zone. Based on the hot ductilitymeasurement of two typical container used steels, it is known that the steels are in severeembrittlement state in the temperature range of 825-775 deg C. By means of increasing Cr/Ni platingthickness on the upper part of the mold, reducing mold heat flux, adopting new secondary coolingpattern, etc., the occurrence of the surface longitudinal cracks on the steel CC (continuouscasting) slabs has been significantly reduced.展开更多
Surface crack of components of the cast nickel base superalloy was repaired with twin laser beams under proper technological conditions. One laser beam was used to melt the substrate material of crack, and the other t...Surface crack of components of the cast nickel base superalloy was repaired with twin laser beams under proper technological conditions. One laser beam was used to melt the substrate material of crack, and the other to fill in powder material to the crack region. The experimental results show that the surface crack with the width of 0.1 ～ 0.3?mm could be repaired under the laser power of 3?kW and the scanning speed of 6 ～ 8?mm/s. The repaired deepness of crack region is below 6.5?mm. The microstructure of repaired region is the cellular crystal, columnar crystal dendrite crystal from the transition region to the top filled layer. The phases in repaired region mainly consisted of supersaturated α Co with plenty of Ni, some Cr and Al, Cr 23 C 6, Co 2B, Co Ni Mo, Ni 4B 3, TiSi and VSi. The hardness of filled layer in repaired region ranged from HV 0.2 450 to HV 0.2 500, and the hardness decreases gradually from the filled layer to joined zone.展开更多
The brittle fracture mode close to the surface of Inconel 718 subsea bolts is closely related to their nanostructure. When the bolts are used subsea under cathodic protection, hydrogen evolves. Intergranular precipita...The brittle fracture mode close to the surface of Inconel 718 subsea bolts is closely related to their nanostructure. When the bolts are used subsea under cathodic protection, hydrogen evolves. Intergranular precipitates and points of intersection of slip lines always held responsible for hydrogen enhanced decohesion. However, thus far, little attention has been paid to the bolts manufacturing method and to the characterization of the role of subsurface oversized nanoprecipitates on transgranular surface cracking. As-received subsea bolts were analyzed using multi-scale observation techniques such as focused ion beam milling, scanning electron microscopy, transmission electron microscopy, and in-air strain rate tensile tests. The results further demonstrated that under identical API aging, there was a difference in the morphological precipitation and strength of 718 as a bolt and rectangular billet. For the 718 rectangular billets, discrete intergranular stable <em>δ</em>/MC carbides precipitate and only <em>γ</em>' of 10 - 20 nm was observed for the bulk and subsurface. Whereas, for the CRA subsea bolt, <em>γ</em>' was approximately 30 nm, <em>γ</em>" was 30 - 50 nm for the bulk (370 HV);<em>γ</em>' was approximately 50 nm and γ" was 50 - 100 nm at subsurface (400 HV). As-received subsea bolts were investigated at subsurface (10 μm from the surface) at the thread and shank region, which revealed transgranular sheared oversized ~50 nm <em>γ</em>' (with dislocation networks) and metastable <em>γ</em>" > 100 nm particles, respectively. Thus, an effort was made to develop the hydrogen-assisted surface cracking theory for bolts.展开更多
Laser spot thermography is a novel technique for the detection of surface cracks with a laser to heat sample locally and with an IR camera to record the surface temperature distribution. Common methods to characterize...Laser spot thermography is a novel technique for the detection of surface cracks with a laser to heat sample locally and with an IR camera to record the surface temperature distribution. Common methods to characterize cracks are only suitable for the situation that the laser scanning path is vertical to the crack. But due to the randomness of cracks,when the scanning path is parallel to the crack,surface cracks cannot be detected by these methods. To tackle this problem,a method is presented which is suitable for the situation that the scanning path is parallel to crack. The main idea is to evaluate the crack-caused asymmetries of the surface temperature distribution. The effect of temperature gradient and the maximum scanning interval are analyzed by a 2D simulation. A new crack imaging technique is presented that is based on delayed temperature difference at symmetric points to characterize the crack in the thermal image. Compared well with those obtained by the spatial first derivative method,experimental results are shown to efficiently prove this method.展开更多
This work presents some numerical aspects of isogeometric boundary element methods(IGABEM).The behavior of hyper-singular and nearly-singular integration is first explored on the distorted NURBS surface.Several numeri...This work presents some numerical aspects of isogeometric boundary element methods(IGABEM).The behavior of hyper-singular and nearly-singular integration is first explored on the distorted NURBS surface.Several numerical treatments are proposed to enhance the quadrature in the framework of isogeometric analysis.Then a numerical implementation of IGABEM on the trimmed NURBS is detailed.Based on this idea,the surface crack problem is modeled incorporation with the phantom element method.The proposed method allows the crack to intersect with the boundary of the body while preserving the original parametrization of the NURBS-based CAD geometry.展开更多
In this work,the stress intensity factors(SIFs)for a wide range of semi-elliptical surface cracks with different inclination angles in a cylindrical bar subjected to pure tension were investigated numerically.The main...In this work,the stress intensity factors(SIFs)for a wide range of semi-elliptical surface cracks with different inclination angles in a cylindrical bar subjected to pure tension were investigated numerically.The main parameters considered to evaluate the SIFs were the crack size ratio(a/d),the crack aspect ratio(a/c),and the crack inclination angle(0).The dual-boundary element met hod implemented in software BEASY was used to compute the SIF values for cracks.Furt her more,the general closed-form solutions were proposed to evaluate the corresponding SIFs for Mode I,Mode II and Mode III types of fracture through curve fitting approaches.These solutions can provide accurate and reliable values of stress intensity factors for a crack on a cylindrical bar under pure tension in a rapid way compared to those obtained using computational models.In addition,these results can be used as inputs for failure studies and life evaluations of cracked cylinder under working conditions.展开更多
文摘In this work,the influences of surface layer slurry at different temperatures(10℃,14℃,18℃,22℃)on wax patterns deformation,shrinkage,slurry coating characteristics,and the surface quality of the casting were investigated by using a single factor variable method.The surface morphologies of the shell molds produced by different temperatures of the surface(first)layer slurries were observed via electron microscopy.Furthermore,the microscopic composition of these shell molds was obtained by EDS,and the osmotic effect of the slurry on the wax patterns at different temperatures was also assessed by the PZ-200 Contact Angle detector.The forming reasons for the surface cracks and holes of thick and large ZTC4 titanium alloy by investment casting were analyzed.The experimental results show that the surface of the shell molds prepared by the surface layer slurry with a low temperature exhibits noticeable damage,which is mainly due to the poor coating performance and the serious expansion and contraction of wax pattern at low temperatures.The second layer shell material(SiO_(2),Al_(2)O_(3))immerses into the crack area of the surface layer,contacts and reacts with the molten titanium to form surface cracks and holes in the castings.With the increase of the temperature of surface layer slurry,the damage to the shell surface tends to weaken,and the composition of the shell molds'surface becomes more uniform with less impurities.The results show that the surface layer slurry at 22℃is evenly coated on the surface of the wax patterns with appropriate thickness,and there is no surface shell mold rupture caused by sliding slurry after sand leaching.The surface layer slurry temperature is consistent with the wax pattern temperature and the workshop temperature,so there is no damage of the surface layer shell caused by expansion and contraction.Therefore,the shell mold prepared by the surface layer slurry at this temperature has good integrity,isolating the contact between the low inert shell material and the titanium liquid effectively,and the ZTC4 titanium alloy cylinder casting prepared by this shell mold is smooth,without cracks and holes.
基金supported by the Centre for Development of Advanced Computing (CDAC), Pune
文摘In hilly regions,the existence of surface cracks in rock mass induces a potential threat to structural stability.Thus,the present research aims to explore the impact of surface cracks on the loadbearing capacity of strip footing placed on the rock mass.By taking into account the various boundary constraints across the surface of crack edges,the study investigates the presence of two categories of surface cracks,namely(1)separated crack,and(2)fine crack.The lower bound limit analysis is employed in conjunction with the finite element method(LBFELA)to conduct the numerical analysis.In order to evaluate rock mass yielding,the power conic programming(PCP)method is utilized to implement the generalized Hoek-Brown(GHB)failure criterion.The stability of the strip footing is analyzed by determining the bearing capacity factor(Nσγ),which is presented in the form of design charts by varying the strength parameters of rock,including the Geological Strength Index(GSI),Hoek-Brown material parameter(mi),Disturbance factor(D),and Normalised Uniaxial Compressive Strength(σci/γB),whereγis the unit weight of rock mass,and B is the width of strip footing.The study also investigates the impact of cracks on strip footings,considering different positions of the crack(LC)and depths of the crack(DC).The results demonstrate that the influence of the fine crack is only noticeable until the LC/B ratio reaches 6.However,for the separated crack,its impact remains significant even when the LC/B ratio exceeds 16.The appearance of fine crack at the edge of the footing results in a decrease in the magnitude Nσγof up to 45%,indicating a substantial reduction in the stability of the footing.The failure patterns are presented and discussed in detail for various cases in this study to examine the effect of surface cracks on the strip footing and to address the extent of the plastic collapse.
基金The article was funded by the National Natural Science Foundation of China(Nos.51674190 and 52074211)the Natural Science Basic Research Program of Shaanxi(Nos.2019JQ-798 and 2019JLP-08).The authors also thank the reviewers for their patient work.
文摘In order to ensure safe mining and reduce surface damage in shallow multi-seam mining,the failure characteristics of interburden strata with different coal pillars offset distances between pillars in the upper and lower seams,the distribution characteristics of stress concentration in coal pillars,and the development characteristics of stratum cracks and subsidence were investigated by physical and UDEC2D simulation.Meanwhile,the effect of different coal pillar offset distances on stress concentration of coal pillar and development of stratum cracks were studied.Based on those results,a formula for safe mining and reducing surface damage was established,which provided a theoretical basis for safe and environmentally friendly mining in shallow multi-seam.According to the results,the optimal coal pillar offset distance(the side to side horizontal distance of the upper and lower coal pillars)between the upper and lower coal seams was developed to reduce the stress concentration of coal pillars and surface damage.The results of this study have been applied in Ningtiaota coal mine and have achieved good results in safe and environmentally friendly mining.
基金This work was financially supported by the National Natural Science Foundation of China (No.50235030, 50505052).
文摘Static tensile test and tensile-tensile fatigue test of medium carbon steel sheet specimens with surface crack precut were performed on MTS810 hydraulic testing machine to clear the meaning of the point of Hp(y) value zero. Magnetic memory signals were measured during the test process. The results show that only one point of Hp(y) zero value exists in all measured magnetic signal curves during the loading process, which should be a sign of intersection of positive-negative magnetic poles after magnetic ordered state appears and does not indicate the position of surface crack precut. The analysis shows that the surface crack precut can not interrupt the magnetic ordered state occurred during the test completely, hence its Hp(y) value is not zero. However, the crack extending to a penetrated defect at the instant of specimen′s fracture leads to the discontinuance of magnetic ordered state.
文摘The effect of alloy segregation and delta （δ） ferrite contents on surface cracking of three standard （i.e. AISI 304L, AISI 310S and AISI 321） and two low nickel （i.e. LNi-1 and LNi-0.3） austenitic stainless steels （ASS） during hot roiling was investigated using optical microscopy （OM）, automatic image analyzer, scanning electron microscopy （SEM）, energy dispersive X-ray spectroscopy （EDX） and electron probe micro analyzer （EPMA）. It was observed that the amount of 6-ferrite varied among different grades and also distributed heterogeneously across the width of the steel plates. In general, low nickel ASS showed higher amount of 6-ferrite compared to the standard ASS grades. The tendency to surface cracking during hot rolling gradually increased with increasing 6-ferrite content. Interestingly, carbon and nitrogen exerted maximum effect on 6-ferrite formation. The higher carbon and nitrogen content in the steel decreased 6-ferMte content. In addition, the segregation of Cu and Mn plays significant role in low nickel ASS and Ni-Cr in case of standard ASS has profound effect on surface cracking of the steel plates. A possible cause of surface crack formation/origination in steel plates during hot rolling was discussed.
基金the National Natural Science Foundation of China (No. 11072205)
文摘A theoretical model of semi-elliptic surface crack growth based on the low cycle strain damage accumulation near the crack tip along the cracking direction and the Newman-Raju formula is developed. The crack is regarded as a sharp notch with a small curvature radius and the process zone is assumed to be the size of cyclic plastic zone. The modified Hutchinson, Rice and Rosengren （HRR） formulations are used in the presented study. Assuming that the shape of surface crack front is controlled by two critical points： the deepest point and the surface point. The theoretical model is applied to semi-elliptic surface cracked A1 7075-T6 alloy plate under cyclic loading, and five different initial crack shapes are discussed in present study. Good agreement between experimental and theoretical results is obtained.
基金supported by the National Science and Technology Support Plan of China(No.2007BAF02B01-03)
文摘18Mn18Cr0.5N steel specimens were preheated at the temperatures from 1100 to 1250°C for 5 min,and then cooled to 950°C and compressed.The cracking behaviors were investigated using optical microscopy and scanning electron microscopy.The results showed that the hot workability of 18Mn18Cr0.5N steel gradually decreased with increasing preheating temperature between 1100 and 1200°C,and quickly deteriorated up to 1250°C.Above 1200°C,delta ferrite particles appeared in 18Mn18Cr0.5N steel,promoted cavity coalescence on grain boundary,and accelerated surface crack formation during the hot working process.
文摘Based on the production practice of medium carbon thin slabs in the CSP plant,the reasons and influencing factors for the formation of longitudinal cracks were investigated,and some industrial measures were taken to eliminate the cracks.The results show that the efficient solutions to reduce longitudinal cracks are improving the performance of the mold powder,stabilizing the mold heat flux,and maintaining a proper taper of the mold during casting.Proper pouring temperature and secondary cooling also play important roles in preventing longitudinal surface cracks.
文摘Three-dimensional crack closure correction methods are investigated in this paper.The fatigue crack growth tests of surface cracks in 14MnNbq steel for bridge plate subjected to tensile and bending loadings are systematically conducted.The experimentally measured fatigue crack growth rates of surface cracks are compared with those of through-thickness cracks in detail.It is found that the crack growth rates of surface cracks are lower than those of through-thickness cracks.In order to correct their differences in fatigue crack growth rates, a dimensionless crack closure correction model is proposed.Although this correction model is determined only by the experimental data of surface cracks under tensile loading with a constant ratio R=0.05, it can correlate the surface crack growth rates with reasonable accuracy under tensile and bending loadings with various stress ratios ranging from 0 to 0.5.Furthermore, predictions of fatigue life and crack aspect ratio for surface cracks are discussed, and the predicted results are also compared with those obtained from other prediction approaches.Comparison results show that the proposed crack closure correction model gives better prediction of fatigue life than other models.
基金the National Natural Science Foundation of China (Nos. 50904067 and 51104156)the New Century Excellent Talents in University (No. NCET-10-0768) for their support of this project
文摘In this paper, simulated experiment device of coal and gas outburst was employed to perform the experiment on gas-containing coal extrusion. In the experiment, coal surface cracks were observed with a high-speed camera and then the images were processed by sketch. Based on the above description, the paper studied the fractal dimension values from different positions of coal surface as well as their changing laws with time. The results show that there is a growing parabola trend of crack dimension value in the process of coal extrusion. Accordingly, we drew the conclusion that extruded coal crack evolution is a process of fractal dimension value increase. On the basis of fractal dimension values taken from different parts of coal masses, a fractal dimension of the contour map was drawn. Thus, it is clear that the contour map involves different crack fractal dimension values from different positions. To be specific, where there are complicated force and violent movement in coal mass, there are higher fractal dimension values, i.e., the further the middle of observation surface is from the exit of coal mass, and the lower the fractal dimension value is. In line with fractal geometry and energy theory of coal and gas outburst, this study presents the relation between fractal dimension and energy in the process of extruding. In conclusion, the evolution of crack fractal dimension value can signify that of energy, which has laid a solid foundation for the quantification research on the mechanism of gas-containing coal extrusion.
基金supported by the National Natural Science Foundation of China(11002122,51172192,11272275,and 10828205)the Natural Science Foundation of Hunan Province(11JJ4003)+1 种基金the Key Project of Scientific Research Conditions in Hunan Province(2012TT2040)The specimens were provided by the AVIC Shenyang Liming Aero-Engine(GROUP)Corporation Ltd
文摘In this paper, a modified shear-lag model is developed to calculate the surface crack density in thermal barrier coatings（TBCs）. The mechanical properties of TBCs are also measured to quantitatively assess their surface crack density. Acoustic emission（AE） and digital image correlation methods are applied to monitor the surface cracking in TBCs under tensile loading. The results show that the calculated surface crack density from the modified model is in agreement with that obtained from experiments. The surface cracking process of TBCs can be discriminated by their AE characteristics and strain evolution. Based on the correlation of energy released from cracking and its corresponding AE signals, a linear relationship is built up between the surface crack density and AE parameters, with the slope being dependent on the mechanical properties of TBCs.
文摘To avoid leaking or bursing by crack on surface of preddure vessels made of streels,a method for analyzing the principle of propagation of a surface crack is established,and used on a spherical vessel with program calculation and simulation,the program is written in QBASIC and the reaults are provided and discussed.
文摘The Monte- Carlo method is used to simulate the surface fatigue crack growth rate for offshore structural steel E36-Z35, and to determine the distributions and relevance of the parameters in the Paris equation. By this method, the time and cost of fatigue crack propagation testing can be reduced. The application of the method is demonstrated by use of four sets of fatigue crack propagation data for offshore structural steel E36-Z35. A comparison of the test data with the theoretical prediction for surface crack growth rate shows the application of the simulation method to the fatigue crack propagation tests is successful.
基金Project supported by the National Natural Science Foundation of China (No.10176003).
文摘In this paper a semi-elliptic surface crack problem in an elastic solid of finite size under impact loading is investigated. An analysis is performed by means of fracture dynamics and the finite element method, and a three-dimensional finite element program is developed to compute the dynamic stress intensity factor. The results reveal that the effects of the solid＇s boundary surface, crack surface, material inertia and stress wave interactions play significant roles in dynamic fracture.
文摘The fact that the amount of the mold flux components differs at differentlocations on the cracking surface indicates that the longitudinal surface cracks are initiallyformed in the mold and are enlarged in the secondary cooling zone. Based on the hot ductilitymeasurement of two typical container used steels, it is known that the steels are in severeembrittlement state in the temperature range of 825-775 deg C. By means of increasing Cr/Ni platingthickness on the upper part of the mold, reducing mold heat flux, adopting new secondary coolingpattern, etc., the occurrence of the surface longitudinal cracks on the steel CC (continuouscasting) slabs has been significantly reduced.
文摘Surface crack of components of the cast nickel base superalloy was repaired with twin laser beams under proper technological conditions. One laser beam was used to melt the substrate material of crack, and the other to fill in powder material to the crack region. The experimental results show that the surface crack with the width of 0.1 ～ 0.3?mm could be repaired under the laser power of 3?kW and the scanning speed of 6 ～ 8?mm/s. The repaired deepness of crack region is below 6.5?mm. The microstructure of repaired region is the cellular crystal, columnar crystal dendrite crystal from the transition region to the top filled layer. The phases in repaired region mainly consisted of supersaturated α Co with plenty of Ni, some Cr and Al, Cr 23 C 6, Co 2B, Co Ni Mo, Ni 4B 3, TiSi and VSi. The hardness of filled layer in repaired region ranged from HV 0.2 450 to HV 0.2 500, and the hardness decreases gradually from the filled layer to joined zone.
文摘The brittle fracture mode close to the surface of Inconel 718 subsea bolts is closely related to their nanostructure. When the bolts are used subsea under cathodic protection, hydrogen evolves. Intergranular precipitates and points of intersection of slip lines always held responsible for hydrogen enhanced decohesion. However, thus far, little attention has been paid to the bolts manufacturing method and to the characterization of the role of subsurface oversized nanoprecipitates on transgranular surface cracking. As-received subsea bolts were analyzed using multi-scale observation techniques such as focused ion beam milling, scanning electron microscopy, transmission electron microscopy, and in-air strain rate tensile tests. The results further demonstrated that under identical API aging, there was a difference in the morphological precipitation and strength of 718 as a bolt and rectangular billet. For the 718 rectangular billets, discrete intergranular stable <em>δ</em>/MC carbides precipitate and only <em>γ</em>' of 10 - 20 nm was observed for the bulk and subsurface. Whereas, for the CRA subsea bolt, <em>γ</em>' was approximately 30 nm, <em>γ</em>" was 30 - 50 nm for the bulk (370 HV);<em>γ</em>' was approximately 50 nm and γ" was 50 - 100 nm at subsurface (400 HV). As-received subsea bolts were investigated at subsurface (10 μm from the surface) at the thread and shank region, which revealed transgranular sheared oversized ~50 nm <em>γ</em>' (with dislocation networks) and metastable <em>γ</em>" > 100 nm particles, respectively. Thus, an effort was made to develop the hydrogen-assisted surface cracking theory for bolts.
基金supported by the National Key Scientific Instrument and Equipment Development Projects,China(Grant No.2013YQ470767)。
文摘Laser spot thermography is a novel technique for the detection of surface cracks with a laser to heat sample locally and with an IR camera to record the surface temperature distribution. Common methods to characterize cracks are only suitable for the situation that the laser scanning path is vertical to the crack. But due to the randomness of cracks,when the scanning path is parallel to the crack,surface cracks cannot be detected by these methods. To tackle this problem,a method is presented which is suitable for the situation that the scanning path is parallel to crack. The main idea is to evaluate the crack-caused asymmetries of the surface temperature distribution. The effect of temperature gradient and the maximum scanning interval are analyzed by a 2D simulation. A new crack imaging technique is presented that is based on delayed temperature difference at symmetric points to characterize the crack in the thermal image. Compared well with those obtained by the spatial first derivative method,experimental results are shown to efficiently prove this method.
基金National Natural Science Foundation of China(NSFC)under Grant(No.51904202).
文摘This work presents some numerical aspects of isogeometric boundary element methods(IGABEM).The behavior of hyper-singular and nearly-singular integration is first explored on the distorted NURBS surface.Several numerical treatments are proposed to enhance the quadrature in the framework of isogeometric analysis.Then a numerical implementation of IGABEM on the trimmed NURBS is detailed.Based on this idea,the surface crack problem is modeled incorporation with the phantom element method.The proposed method allows the crack to intersect with the boundary of the body while preserving the original parametrization of the NURBS-based CAD geometry.
文摘In this work,the stress intensity factors(SIFs)for a wide range of semi-elliptical surface cracks with different inclination angles in a cylindrical bar subjected to pure tension were investigated numerically.The main parameters considered to evaluate the SIFs were the crack size ratio(a/d),the crack aspect ratio(a/c),and the crack inclination angle(0).The dual-boundary element met hod implemented in software BEASY was used to compute the SIF values for cracks.Furt her more,the general closed-form solutions were proposed to evaluate the corresponding SIFs for Mode I,Mode II and Mode III types of fracture through curve fitting approaches.These solutions can provide accurate and reliable values of stress intensity factors for a crack on a cylindrical bar under pure tension in a rapid way compared to those obtained using computational models.In addition,these results can be used as inputs for failure studies and life evaluations of cracked cylinder under working conditions.
