The surrounding rock is prone to large-scale loosening and failure after the excavation of shallow large-span caverns because of the thin overlying strata and large cross-section span.The rational design of bolt suppo...The surrounding rock is prone to large-scale loosening and failure after the excavation of shallow large-span caverns because of the thin overlying strata and large cross-section span.The rational design of bolt support is very important to the safety control of surrounding rock as a common support means.The control mechanism and design method of bolt support for shallow-buried large-span caverns is carried out.The calculation method of bolt prestress and length based on arched failure and collapsed failure mode is established.The influence mechanism of different influencing factors on the bolt prestress and length is clarified.At the same time,the constant resistance energy-absorbing bolt with high strength and high toughness is developed,and the comparative test of mechanical properties is carried out.On this basis,the design method of high prestressed bolt support for shallow-buried large-span caverns is put forward,and the field test is carried out in Qingdao metro station in China.The monitoring results show that the maximum roof settlement is 6.8 mm after the new design method is adopted,and the effective control of the shallow-buried large-span caverns is realized.The research results can provide theoretical and technical support for the safety control of shallow-buried large-span caverns.展开更多
Due to the long-term plate tectonic movements in southwestern China,the in-situ stress field in deep formations is complex.When passing through deep soft-rock mass under non-hydrostatic high in-situ stress field,tunne...Due to the long-term plate tectonic movements in southwestern China,the in-situ stress field in deep formations is complex.When passing through deep soft-rock mass under non-hydrostatic high in-situ stress field,tunnels will suffer serious asymmetric deformation.There is no available support design method for tunnels under such a situation in existing studies to clarify the support time and support stiffness.This study first analyzed the mechanical behavior of tunnels in non-hydrostatic in-situ stress field and derived the theoretical equations of the ground squeezing curve(GSC)and ground loosening curve(GLC).Then,based on the convergence confinement theory,the support design method of deep soft-rock tunnels under non-hydrostatic high in-situ stress field was established considering both squeezing and loosening pressures.In addition,this method can provide the clear support time and support stiffness of the second layer of initial support.The proposed design method was applied to the Wanhe tunnel of the China-Laos railway in China.Monitoring data indicated that the optimal support scheme had a good effect on controlling the tunnel deformation in non-hydrostatic high in-situ stress field.Field applications showed that the secondary lining could be constructed properly.展开更多
Inadequate decision support tools have led to selection of inappropriate wastewater treatment technologies.The objectives of this research were to investigate performance data for wastewater treatment technologies,dev...Inadequate decision support tools have led to selection of inappropriate wastewater treatment technologies.The objectives of this research were to investigate performance data for wastewater treatment technologies,develop a Decision Support Method(DSM)for evaluating performance of technologies,and to validate the developed method.The method was developed through evaluation of performance of wastewater treatment technologies against environmental and economic indicators.Fuzzy logic techniques in form of linguistic variables were applied in order to support decision making under uncertainty.The DSM relied on performance evaluation in order to rate effectiveness of wastewater treatment technologies.DSM was validated through a training tool in ED-WAVE,a model developed by a consortium of European and Asian countries.The reliance of the DSM on performance evaluation was an improvement on the existing decision support tools such as ED-WAVE that relied on retrieval of past performance data.As DSM integrated environmental and economic factors in evaluating wastewater treatment technologies,it was thus able to select a process that was not only environmentally sustainable but also economically affordable.展开更多
According to military requirement, and based on the problems of equipmentmaintenance support methods in high-tech battles, each element supporting equipment maintenance isanalyzed, and the methods for improving equipm...According to military requirement, and based on the problems of equipmentmaintenance support methods in high-tech battles, each element supporting equipment maintenance isanalyzed, and the methods for improving equipment maintenance are proposed.展开更多
Eight casing failure modes and 32 risk factors in oil and gas wells are given in this paper. According to the quantitative analysis of the influence degree and occurrence probability of risk factors, the Borda counts ...Eight casing failure modes and 32 risk factors in oil and gas wells are given in this paper. According to the quantitative analysis of the influence degree and occurrence probability of risk factors, the Borda counts for failure modes are obtained with the Borda method. The risk indexes of failure modes are derived from the Borda matrix. Based on the support vector machine （SVM）, a casing life prediction model is established. In the prediction model, eight risk indexes are defined as input vectors and casing life is defined as the output vector. The ideal model parameters are determined with the training set from 19 wells with casing failure. The casing life prediction software is developed with the SVM model as a predictor. The residual life of 60 wells with casing failure is predicted with the software, and then compared with the actual casing life. The comparison results show that the casing life prediction software with the SVM model has high accuracy.展开更多
Center of gravity(COG)is an important parameter of projectiles and rockets,for which supporting reaction method(or support reaction method)is an important COG measurement method.Based on this supporting reaction metho...Center of gravity(COG)is an important parameter of projectiles and rockets,for which supporting reaction method(or support reaction method)is an important COG measurement method.Based on this supporting reaction method a novel design method is proposed to determine the key design parameters of the COG measurement system.The method can quantitatively analyze the influence of the design parameters on the COG accuracy,in the measurement system designed with supporting reaction method.Using the principle of static balance,the error propagation theory,and the system accuracy analysis method,the equal-range required sensor precision(RSP)surface and non-equal-range required sensor pair precision(RSPP)adapted surface are adopted.The influence of random errors(like sensor accuracy and distance calibration accuracy)is analyzed.The selection strategy of equal-range and non-equal-range sensors is chosen,and then the recommended calibration accuracy values are obtained.For the quality detection accuracy of±0.6 kg and the axial COG detection accuracy of±1.5 mm,the RSP surface is drawn by the proposed method,and the force sensor with±0.23 kg detection accuracy is selected.The experimental verification meets the accuracy requirements and verifies the effectiveness of the proposed design method for the system parameters of the COG measurement equipment.展开更多
This paper presents a computer system reliability allocation method that is based on the theory of statistic and Markovian chain,which can be used to allocate reliability to subsystem, to hybrid system and software mo...This paper presents a computer system reliability allocation method that is based on the theory of statistic and Markovian chain,which can be used to allocate reliability to subsystem, to hybrid system and software modules. A relevant supporting tool built by us is introduced.展开更多
The influencing factors of the equipment support activity process have the characteristics of nonlinearity, high dimension, many constraints, random uncertainty and fuzzy uncertainty. Monte Carlo method can solve the ...The influencing factors of the equipment support activity process have the characteristics of nonlinearity, high dimension, many constraints, random uncertainty and fuzzy uncertainty. Monte Carlo method can solve the above problems commendably. This paper analyzes the main equipment support activity process and establishes the sampling plan and simulation model of the medium maintenance process based on Monte Carlo method, and the simulation result verifies a fact that the medium maintenance time can be effectively reduced when parallel operation on some procedures is used. It has a practical value and can give good advice to achieve the capability of equipment supportability.展开更多
To ameliorate reliability analysis efficiency for aeroengine components, such as compressor blade, support vector machine response surface method(SRSM) is proposed. SRSM integrates the advantages of support vector mac...To ameliorate reliability analysis efficiency for aeroengine components, such as compressor blade, support vector machine response surface method(SRSM) is proposed. SRSM integrates the advantages of support vector machine(SVM) and traditional response surface method(RSM), and utilizes experimental samples to construct a suitable response surface function(RSF) to replace the complicated and abstract finite element model. Moreover, the randomness of material parameters, structural dimension and operating condition are considered during extracting data so that the response surface function is more agreeable to the practical model. The results indicate that based on the same experimental data, SRSM has come closer than RSM reliability to approximating Monte Carlo method(MCM); while SRSM(17.296 s) needs far less running time than MCM(10958 s) and RSM(9840 s). Therefore,under the same simulation conditions, SRSM has the largest analysis efficiency, and can be considered a feasible and valid method to analyze structural reliability.展开更多
In aircraft structural dynamic design the matching of guns with their supporting structure is one of the most important tasks on which hinges the success or failure of the structural design. The design curves for matc...In aircraft structural dynamic design the matching of guns with their supporting structure is one of the most important tasks on which hinges the success or failure of the structural design. The design curves for matching guns with their supporting structure can be obtained from response calculations of the plate-spring system supporting the gun on the ground,the model structure tested on the ground and the actual structure.A set of matching curves is given for engineering application.Then,the matching design can be accomplished by means of impact load spectrograms so as to perform an optimal structural design and to make further improvements on dynamic design program.展开更多
An aqueous sol-gel method for the synthesis of γ-Al2O3 supports has been developed for the use in tar reforming applications. It was determined the influences of two different aluminum precursors (aluminum sec-butoxi...An aqueous sol-gel method for the synthesis of γ-Al2O3 supports has been developed for the use in tar reforming applications. It was determined the influences of two different aluminum precursors (aluminum sec-butoxide (Al[OCH(CH3)CH2CH3]3) and aluminum nitrate (Al(NO3)3)) on the textural and crystallographic properties of Al2O3 supports. Only the formation of γ-Al2O3 is aimed in order to use these alumina materials as catalytic supports, because it presents high specific surface area and pore volume values. Additionally, the synthesis of γ-Al2O3 was realized with the use of a functionalized silicon precursor, [3-(2-aminoethylamino)propyl]trimethoxysilane, called EDAS. By the presence of an ethylenediamine group in this molecule, it is possible to chelate metallic ions and to highly increase their dispersion at a molecular level during the synthesis of metallic catalysts supported on alumina, which is an asset for catalytic applications. So it was developed a synthesis sol-gel procedure for the cogelation between the functionalized silicon alkoxide EDAS and alumina precursor. The alumina supports synthesized with Al(NO3)3 as precursor presented higher porous values than the ones obtained with aluminium sec-butoxide precursor. Since nitrate salts are much easier to handle than alkoxides, these observations allowed validating Al(NO3)3 as aluminum source for the future synthesis procedures for metallic catalysts supported on alumina.展开更多
Large catalogues of classified galaxy images have been useful in many studies of the universe in astronomy. There are too many objects to classify manually in the Sloan Digital Sky Survey, one of the premier data sour...Large catalogues of classified galaxy images have been useful in many studies of the universe in astronomy. There are too many objects to classify manually in the Sloan Digital Sky Survey, one of the premier data sources in astronomy. Therefore, efficient machine learning and classification algorithms are required to automate the classifying process. We propose to apply the Support Vector Machine (SVM) algorithm to classify galaxy morphologies and Krylov iterative methods to improve runtime of the classification. The accuracy of the classification is measured on various categories of galaxies from the survey. A three-class algorithm is presented that makes use of multiple SVMs. This algorithm is used to assign the categories of spiral, elliptical, and irregular galaxies. A selection of Krylov iterative solvers are compared based on their efficiency and accuracy of the resulting classification. The experimental results demonstrate that runtime can be significantly improved by utilizing Krylov iterative methods without impacting classification accuracy. The generalized minimal residual method (GMRES) is shown to be the most efficient solver to classify galaxy morphologies.展开更多
The element-free Galerkin method is proposed to solve free vibration of rectangular plates with finite interior elastic point supports and elastically restrained edges.Based on the extended Hamilton＇s principle for t...The element-free Galerkin method is proposed to solve free vibration of rectangular plates with finite interior elastic point supports and elastically restrained edges.Based on the extended Hamilton＇s principle for the elastic dynamics system,the dimensionless equations of motion of rectangular plates with finite interior elastic point supports and the edge elastically restrained are established using the element-free Galerkin method.Through numerical calculation,curves of the natural frequency of thin plates with three edges simply supported and one edge elastically restrained,and three edges clamped and the other edge elastically restrained versus the spring constant,locations of elastic point support and the elastic stiffness of edge elastically restrained are obtained.Effects of elastic point supports and edge elastically restrained on the free vibration characteristics of the thin plates are analyzed.展开更多
基金Project(2023YFC3805700) supported by the National Key Research and Development Program of ChinaProjects(42477166,42277174) supported by the National Natural Science Foundation of China+2 种基金Project(2024JCCXSB01) supported by the Fundamental Research Funds for the Central Universities,ChinaProject(KFJJ24-01M) supported by the State Key Laboratory of Explosion Science and Safety Protection,Beijing Institute of Technology,ChinaProject(HLCX-2024-04) supported by the Open Foundation of Collaborative Innovation Center of Green Development and Ecological Restoration of Mineral Resources,China。
文摘The surrounding rock is prone to large-scale loosening and failure after the excavation of shallow large-span caverns because of the thin overlying strata and large cross-section span.The rational design of bolt support is very important to the safety control of surrounding rock as a common support means.The control mechanism and design method of bolt support for shallow-buried large-span caverns is carried out.The calculation method of bolt prestress and length based on arched failure and collapsed failure mode is established.The influence mechanism of different influencing factors on the bolt prestress and length is clarified.At the same time,the constant resistance energy-absorbing bolt with high strength and high toughness is developed,and the comparative test of mechanical properties is carried out.On this basis,the design method of high prestressed bolt support for shallow-buried large-span caverns is put forward,and the field test is carried out in Qingdao metro station in China.The monitoring results show that the maximum roof settlement is 6.8 mm after the new design method is adopted,and the effective control of the shallow-buried large-span caverns is realized.The research results can provide theoretical and technical support for the safety control of shallow-buried large-span caverns.
基金Project(52178402)supported by the National Natural Science Foundation of ChinaProject(2021-Key-09)supported by the Science and Technology Research and Development Program Project of China Railway Group LimitedProject(2021zzts0216)supported by the Innovation-Driven Project of Central South University,China。
文摘Due to the long-term plate tectonic movements in southwestern China,the in-situ stress field in deep formations is complex.When passing through deep soft-rock mass under non-hydrostatic high in-situ stress field,tunnels will suffer serious asymmetric deformation.There is no available support design method for tunnels under such a situation in existing studies to clarify the support time and support stiffness.This study first analyzed the mechanical behavior of tunnels in non-hydrostatic in-situ stress field and derived the theoretical equations of the ground squeezing curve(GSC)and ground loosening curve(GLC).Then,based on the convergence confinement theory,the support design method of deep soft-rock tunnels under non-hydrostatic high in-situ stress field was established considering both squeezing and loosening pressures.In addition,this method can provide the clear support time and support stiffness of the second layer of initial support.The proposed design method was applied to the Wanhe tunnel of the China-Laos railway in China.Monitoring data indicated that the optimal support scheme had a good effect on controlling the tunnel deformation in non-hydrostatic high in-situ stress field.Field applications showed that the secondary lining could be constructed properly.
基金The authors gratefully acknowledge support extended by Jomo Kenyatta University of Agriculture and Technology,the Ministry of Water and Irrigation,Kenya and Lappeenranta University of Technology for research funding through the CIMO-JKUAT training program.
文摘Inadequate decision support tools have led to selection of inappropriate wastewater treatment technologies.The objectives of this research were to investigate performance data for wastewater treatment technologies,develop a Decision Support Method(DSM)for evaluating performance of technologies,and to validate the developed method.The method was developed through evaluation of performance of wastewater treatment technologies against environmental and economic indicators.Fuzzy logic techniques in form of linguistic variables were applied in order to support decision making under uncertainty.The DSM relied on performance evaluation in order to rate effectiveness of wastewater treatment technologies.DSM was validated through a training tool in ED-WAVE,a model developed by a consortium of European and Asian countries.The reliance of the DSM on performance evaluation was an improvement on the existing decision support tools such as ED-WAVE that relied on retrieval of past performance data.As DSM integrated environmental and economic factors in evaluating wastewater treatment technologies,it was thus able to select a process that was not only environmentally sustainable but also economically affordable.
文摘According to military requirement, and based on the problems of equipmentmaintenance support methods in high-tech battles, each element supporting equipment maintenance isanalyzed, and the methods for improving equipment maintenance are proposed.
基金support from "973 Project" (Contract No. 2010CB226706)
文摘Eight casing failure modes and 32 risk factors in oil and gas wells are given in this paper. According to the quantitative analysis of the influence degree and occurrence probability of risk factors, the Borda counts for failure modes are obtained with the Borda method. The risk indexes of failure modes are derived from the Borda matrix. Based on the support vector machine （SVM）, a casing life prediction model is established. In the prediction model, eight risk indexes are defined as input vectors and casing life is defined as the output vector. The ideal model parameters are determined with the training set from 19 wells with casing failure. The casing life prediction software is developed with the SVM model as a predictor. The residual life of 60 wells with casing failure is predicted with the software, and then compared with the actual casing life. The comparison results show that the casing life prediction software with the SVM model has high accuracy.
基金Supported by National Key Research and Development Program of China(2018YFB1306300)。
文摘Center of gravity(COG)is an important parameter of projectiles and rockets,for which supporting reaction method(or support reaction method)is an important COG measurement method.Based on this supporting reaction method a novel design method is proposed to determine the key design parameters of the COG measurement system.The method can quantitatively analyze the influence of the design parameters on the COG accuracy,in the measurement system designed with supporting reaction method.Using the principle of static balance,the error propagation theory,and the system accuracy analysis method,the equal-range required sensor precision(RSP)surface and non-equal-range required sensor pair precision(RSPP)adapted surface are adopted.The influence of random errors(like sensor accuracy and distance calibration accuracy)is analyzed.The selection strategy of equal-range and non-equal-range sensors is chosen,and then the recommended calibration accuracy values are obtained.For the quality detection accuracy of±0.6 kg and the axial COG detection accuracy of±1.5 mm,the RSP surface is drawn by the proposed method,and the force sensor with±0.23 kg detection accuracy is selected.The experimental verification meets the accuracy requirements and verifies the effectiveness of the proposed design method for the system parameters of the COG measurement equipment.
基金Supported by Visiting Scholar Foundation of Key Lab.In University"86 3" High Tech Projects(86 3-30 6 -ZT0 2 -0 4-2 )
文摘This paper presents a computer system reliability allocation method that is based on the theory of statistic and Markovian chain,which can be used to allocate reliability to subsystem, to hybrid system and software modules. A relevant supporting tool built by us is introduced.
基金the Special Research Fund for the Research on Armored Vehicle Supportability Requirement Analysis(No.51319050302)
文摘The influencing factors of the equipment support activity process have the characteristics of nonlinearity, high dimension, many constraints, random uncertainty and fuzzy uncertainty. Monte Carlo method can solve the above problems commendably. This paper analyzes the main equipment support activity process and establishes the sampling plan and simulation model of the medium maintenance process based on Monte Carlo method, and the simulation result verifies a fact that the medium maintenance time can be effectively reduced when parallel operation on some procedures is used. It has a practical value and can give good advice to achieve the capability of equipment supportability.
基金Project(51335003)supported by the National Natural Science Foundation of ChinaProject(20111102110011)supported by the Specialized Research Fund for the Doctoral Program of Higher Education of China
文摘To ameliorate reliability analysis efficiency for aeroengine components, such as compressor blade, support vector machine response surface method(SRSM) is proposed. SRSM integrates the advantages of support vector machine(SVM) and traditional response surface method(RSM), and utilizes experimental samples to construct a suitable response surface function(RSF) to replace the complicated and abstract finite element model. Moreover, the randomness of material parameters, structural dimension and operating condition are considered during extracting data so that the response surface function is more agreeable to the practical model. The results indicate that based on the same experimental data, SRSM has come closer than RSM reliability to approximating Monte Carlo method(MCM); while SRSM(17.296 s) needs far less running time than MCM(10958 s) and RSM(9840 s). Therefore,under the same simulation conditions, SRSM has the largest analysis efficiency, and can be considered a feasible and valid method to analyze structural reliability.
文摘In aircraft structural dynamic design the matching of guns with their supporting structure is one of the most important tasks on which hinges the success or failure of the structural design. The design curves for matching guns with their supporting structure can be obtained from response calculations of the plate-spring system supporting the gun on the ground,the model structure tested on the ground and the actual structure.A set of matching curves is given for engineering application.Then,the matching design can be accomplished by means of impact load spectrograms so as to perform an optimal structural design and to make further improvements on dynamic design program.
文摘An aqueous sol-gel method for the synthesis of γ-Al2O3 supports has been developed for the use in tar reforming applications. It was determined the influences of two different aluminum precursors (aluminum sec-butoxide (Al[OCH(CH3)CH2CH3]3) and aluminum nitrate (Al(NO3)3)) on the textural and crystallographic properties of Al2O3 supports. Only the formation of γ-Al2O3 is aimed in order to use these alumina materials as catalytic supports, because it presents high specific surface area and pore volume values. Additionally, the synthesis of γ-Al2O3 was realized with the use of a functionalized silicon precursor, [3-(2-aminoethylamino)propyl]trimethoxysilane, called EDAS. By the presence of an ethylenediamine group in this molecule, it is possible to chelate metallic ions and to highly increase their dispersion at a molecular level during the synthesis of metallic catalysts supported on alumina, which is an asset for catalytic applications. So it was developed a synthesis sol-gel procedure for the cogelation between the functionalized silicon alkoxide EDAS and alumina precursor. The alumina supports synthesized with Al(NO3)3 as precursor presented higher porous values than the ones obtained with aluminium sec-butoxide precursor. Since nitrate salts are much easier to handle than alkoxides, these observations allowed validating Al(NO3)3 as aluminum source for the future synthesis procedures for metallic catalysts supported on alumina.
文摘Large catalogues of classified galaxy images have been useful in many studies of the universe in astronomy. There are too many objects to classify manually in the Sloan Digital Sky Survey, one of the premier data sources in astronomy. Therefore, efficient machine learning and classification algorithms are required to automate the classifying process. We propose to apply the Support Vector Machine (SVM) algorithm to classify galaxy morphologies and Krylov iterative methods to improve runtime of the classification. The accuracy of the classification is measured on various categories of galaxies from the survey. A three-class algorithm is presented that makes use of multiple SVMs. This algorithm is used to assign the categories of spiral, elliptical, and irregular galaxies. A selection of Krylov iterative solvers are compared based on their efficiency and accuracy of the resulting classification. The experimental results demonstrate that runtime can be significantly improved by utilizing Krylov iterative methods without impacting classification accuracy. The generalized minimal residual method (GMRES) is shown to be the most efficient solver to classify galaxy morphologies.
基金Project supported by the National Natural Science Foundation of China (Grant No.10872163)the Natural Science Foundation of Education Department of Shaanxi Province (Grant No.08JK394)
文摘The element-free Galerkin method is proposed to solve free vibration of rectangular plates with finite interior elastic point supports and elastically restrained edges.Based on the extended Hamilton＇s principle for the elastic dynamics system,the dimensionless equations of motion of rectangular plates with finite interior elastic point supports and the edge elastically restrained are established using the element-free Galerkin method.Through numerical calculation,curves of the natural frequency of thin plates with three edges simply supported and one edge elastically restrained,and three edges clamped and the other edge elastically restrained versus the spring constant,locations of elastic point support and the elastic stiffness of edge elastically restrained are obtained.Effects of elastic point supports and edge elastically restrained on the free vibration characteristics of the thin plates are analyzed.
