The radar cross section （RCS） of weak scattering source on the surface of an aircraft is usually less than -40 dBsm. How to accurately measure the RCS characteristics of weak scattering source is a technical challen...The radar cross section （RCS） of weak scattering source on the surface of an aircraft is usually less than -40 dBsm. How to accurately measure the RCS characteristics of weak scattering source is a technical challenge for the aircraft＇s RCS measurement. This paper proposes separating and extracting the two-dimensional （2D） reflectivity distribution of the weak scattering source with the microwave imaging algorithm and spectral transform so as to enhance its measurement preci- sion. Firstly, we performed the 2D microwave imaging of the target and then used the 2D gating function to separate and extract the reflectivity distribution of the weak scattering source. Secondly, we carried out the spectral transform of the reflectivity distribution and eventually obtained the RCS of the weak scattering source through calibration. The prototype experimental results and their analysis show that the measurement method is effective. The experiments on an aircraft＇s low-scattering conformal antenna verify that the measurement method can eliminate the clutter on the surface of aircraft. The precision of measuring a -40 dBsm target is 3 5 dB better than the existing RCS measurement methods. The measurement method can more accurately obtain the weak scattering source＇s RCS characteristics.展开更多
Micro-focus computed tomography(CT),which allows the hyperfine structure within objects to be reconstructed,is a powerful nondestructive testing tool in many fields.However,current x-ray sources for micro-focus CT are...Micro-focus computed tomography(CT),which allows the hyperfine structure within objects to be reconstructed,is a powerful nondestructive testing tool in many fields.However,current x-ray sources for micro-focus CT are typically limited by their relatively low photon energy and low flux.An all-optical inverse Compton scattering source(AOCS)based on laser wakefield acceleration can generate intense quasi-monoenergetic x/gamma-ray pulses in the kilo-to megaelectronvolt range with micrometer-level source size,and its potential application for micro-focus CT has become very attractive in recent years because of the rapid progress made in laser wakefield acceleration.Reported here is a successful experimental demonstration of high-fidelity micro-focus CT using an AOCS(∼70 keV)by imaging and reconstructing a test object with complex inner structures.A region-of-interest CT method is adopted to utilize the relatively small field of view of the AOCS to ensure high spatial resolution.This demonstration of AOCS-based region-of-interest micro-focus CT is a key step toward its application in the field of hyperfine nondestructive testing.展开更多
N-soliton solutions of the hierarchy of non-isospectral mKdV equation with self-consistent sources andthe hierarchy of non-isospectral sine-Gordon equation with self-consistent sources are obtained via the inverse sca...N-soliton solutions of the hierarchy of non-isospectral mKdV equation with self-consistent sources andthe hierarchy of non-isospectral sine-Gordon equation with self-consistent sources are obtained via the inverse scatteringtransform.展开更多
Separation of the components of rigid acoustic scattering by underwater objects is essential in obtaining the structural characteristics of such objects. To overcome the problem of rigid structures appearing to have t...Separation of the components of rigid acoustic scattering by underwater objects is essential in obtaining the structural characteristics of such objects. To overcome the problem of rigid structures appearing to have the same spectral structure in the time domain, time-frequency Blind Source Separation (BSS) can be used in combination with image morphology to separate the rigid scattering components of different objects. Based on a highlight model, the separation of the rigid scattering structure of objects with time-frequency distribution is deduced. Using a morphological filter, different characteristics in a Wigner-Ville Distribution (WVD) observed for single auto term and cross terms can be simplified to remove any cross-term interference. By selecting time and frequency points of the auto terms signal, the accuracy of BSS can be improved. A simulation experimental has been used to analyze the feasibility of the new method, with changing the pulse width of the transmitted signal, the relative amplitude and the time delay parameter. And simulation results show that the new method can not only separate rigid scattering components, but can also separate the components when elastic scattering and rigid scattering exist at the same time. Experimental results confirm that the new method can be used in separating the rigid scattering structure of underwater objects.展开更多
This paper investigates in detail the dynamics of the modified KdV equation with self-consistent sources, including characteristics of one-soliton, scattering conditions and phase shifts of two solitons, degenerate ca...This paper investigates in detail the dynamics of the modified KdV equation with self-consistent sources, including characteristics of one-soliton, scattering conditions and phase shifts of two solitons, degenerate case of two solitons and ＂ghost＂ solitons, etc. Co-moving coordinate frames are employed in asymptotic analysis.展开更多
Energy spectra, angular distributions, and temporal profiles of the photons produced by an all-optical Thomson scat- tering X-ray source are explored through numerical simulations based on the parameters of the SILEX-...Energy spectra, angular distributions, and temporal profiles of the photons produced by an all-optical Thomson scat- tering X-ray source are explored through numerical simulations based on the parameters of the SILEX-I laser system （800 nm, 30 fs, 300 TW） and the previous wakefield acceleration experimental results. The simulation results show that X-ray pulses with a duration of 30 fs and an emission angle of 50 mrad can be produced from such a source. Using the optimized electron parameters, X-ray pulses with better directivity and narrower energy spectra can be obtained. Besides the electron parameters, the laser parameters such as the wavelength, pulse duration, and spot size also affect the X-ray yield, the angular distribution, and the maximum photon energy, except the X-ray pulse duration which is slightly changed for the case of ultrafast laser-electron interaction.展开更多
In this paper, it is proved the ability of quantity reconstruction, amplitudes and coordinates of metallic strip local scattering sources from the backscattering pattern. They are performed as the results of numerical...In this paper, it is proved the ability of quantity reconstruction, amplitudes and coordinates of metallic strip local scattering sources from the backscattering pattern. They are performed as the results of numerical solution for the infinite perfect conducting strip in case of E-polarization of the incident plane electromagnetic wave. In this case it is necessary to fulfill the following conditions. The local sources amplitudes should be the same order, in transverse and longitudinal directions the local sources should be separated into distances more than apparatus resolution, and the object maximum size does not have to be more than approximately 50λ. It was shown the limit and ability of the further development of the offered method.展开更多
We report our recent progress in the design and simulation of a high-brightness S-band photo-injector with a ballistic bunching scheme aimed at driving an inverse Compton scattering(ICS)X-ray source.By adding a short ...We report our recent progress in the design and simulation of a high-brightness S-band photo-injector with a ballistic bunching scheme aimed at driving an inverse Compton scattering(ICS)X-ray source.By adding a short standing-wave buncher between the RF gun and first booster in a conventional S-band photo-injector,electron bunches with a 500 pC charge can be compressed to the sub-picosecond level with very limited input RF power and an unchanged basic layout of the photo-injector.Beam dynamics analysis indicates that fine tuning of the focusing strength of the gun and linac solenoid can well balance additional focusing provided by the standing wave buncher and generate a well-compensated transverse emittance.Thorough bunching dynamics simulations with different operating conditions of the buncher show that a buncher with more cells and a moderate gradient is suitable for simultaneously obtaining a short bunch duration and low emittance.In a typical case of a 9-cell buncher with a 38 MV/m gradient,an ultrashort bunch duration of 0.5 ps(corresponding to a compression ratio of>5)and a low emittance of<1 mm mrad can be readily obtained for a 500 pC electron pulse.This feasible ballistic bunching scheme will facilitate the implementation of an ultrashort pulse mode inverse Compton scattering X-ray source on most existing S-band photo-injectors.展开更多
The inverse scattering problems are to detect the property of obstacles from the measurements outside the obstacles. One of important research areas in this topic is the recovery of boundary property for impenetrable ...The inverse scattering problems are to detect the property of obstacles from the measurements outside the obstacles. One of important research areas in this topic is the recovery of boundary property for impenetrable obstacles. In this paper, we would like to give a brief review about the recently developed singular source methods. There are three different methods in this category, namely, linear sampling method, pointsource method and probe method. We also present some recent new results about the probe method.展开更多
Glucose molecules are of great significance being one of the most important molecules in metabolic chain.However,due to the small Raman scattering cross-section and weak/non-adsorption on bare metals,accurately obtain...Glucose molecules are of great significance being one of the most important molecules in metabolic chain.However,due to the small Raman scattering cross-section and weak/non-adsorption on bare metals,accurately obtaining their"fingerprint information"remains a huge obstacle.Herein,we developed a tip-enhanced Raman scattering(TERS)technique to address this challenge.Adopting an optical fiber radial vector mode internally illuminates the plasmonic fiber tip to effectively suppress the background noise while generating a strong electric-field enhanced tip hotspot.Furthermore,the tip hotspot approaching the glucose molecules was manipulated via the shear-force feedback to provide more freedom for selecting substrates.Consequently,our TERS technique achieves the visualization of all Raman modes of glucose molecules within spectral window of 400-3200 cm^(-1),which is not achievable through the far-field/surface-enhanced Raman,or the existing TERS techniques.Our TERS technique offers a powerful tool for accurately identifying Raman scattering of molecules,paving the way for biomolecular analysis.展开更多
The application of a controllable neutron source for measuring formation porosity in the advancement of nuclear logging has garnered increased attention.The existing porosity algorithm,which is based on the thermal ne...The application of a controllable neutron source for measuring formation porosity in the advancement of nuclear logging has garnered increased attention.The existing porosity algorithm,which is based on the thermal neutron counting ratio,exhibits lower sensitivity in high-porosity regions.To enhance the sensitivity,the effects of elastic and inelastic scattering,which influence the slowing-down of fast neutrons,were theoretically analyzed,and a slowing-down model of fast neutrons was created.Based on this model,a density correction porosity algorithm was proposed based on the relationship between density,thermal neutron counting ratio,and porosity.Finally,the super multifunctional calculation program for nuclear design and safety evaluation(TopMC/SuperMC)was used to create a simulation model for porosity logging,and its applicability was examined.The results demonstrated that the relative error between the calculated and actual porosities was less than 1%,and the influence of deviation in the density measurement was less than 2%.Therefore,the proposed density correction algorithm based on the slowing-down model of fast neutrons can effectively improve the sensitivity in the high-porosity region.This study is expected to serve as a reference for the application of neutron porosity measurements with D–T neutron sources.展开更多
In neutron and photon transport problems,anisotropic scattering is of great importance for the particle flux,especially when the angular flux has a strong forward peak in shielding analyses.The conventional Legendre e...In neutron and photon transport problems,anisotropic scattering is of great importance for the particle flux,especially when the angular flux has a strong forward peak in shielding analyses.The conventional Legendre expansion is widely used in discrete ordinates transport codes because of algebraic simplifications with spherical harmonics for the scattering source.However,negative cross sections caused by the finitely truncated expansion may give rise to a negative source and flux.A simple method is adopted,based on integrating functions of scattering moments,to evaluate anisotropy and convergence of expanded functions.A series of problems were designed with angular fluxes of different anisotropy,and numerical simulations were performed using the ARES transport code to study different treatments and algorithms for scattering.Results show that the diagonal transport approximation is more stable and obtains a similar accuracy with the extended approximation.A conservative fixup for the negative source could ensure particle balance and improve computational accuracy significantly for photon transport.The effect of anisotropic scattering is problem-dependent,and no distinct differences among various methods are observed for volume source problems with a continuous energy source.For beam source problems,flux results are sensitive to negative scattering functions,and strictly nonnegative cross sections need to be implemented.展开更多
In the paper, Ablowitz–Ladik hierarchy with new self-consistent sources is investigated. First the source in the hierarchy is described as φnφn+1, where φnis related to the Ablowitz–Ladik spectral problem, instea...In the paper, Ablowitz–Ladik hierarchy with new self-consistent sources is investigated. First the source in the hierarchy is described as φnφn+1, where φnis related to the Ablowitz–Ladik spectral problem, instead of the corresponding adjoint spectral problem. Then by means of the inverse scattering transform, the multi-soliton solutions for the hierarchy are obtained. Two reductions to the discrete mKdV and nonlinear Schr¨odinger hierarchies with selfconsistent sources are considered by using the uniqueness of the Jost functions, as well as their N-soliton solutions.展开更多
The theory of elastic wave scattering is a fundamental concept in the study of elastic dynamics and wave motion,and the wave function expansion technique has been widely used in many subjects.To supply the essential t...The theory of elastic wave scattering is a fundamental concept in the study of elastic dynamics and wave motion,and the wave function expansion technique has been widely used in many subjects.To supply the essential tools for solving wave scattering problems induced by an eccentric source or multi-sources as well as multi-scatters,a whole-space transform formula of cylindrical wave functions is presented and its applicability to some simple cases is demonstrated in this study.The transforms of wave functions in cylindrical coordinates can be classifi ed into two basic types: interior transform and exterior transform,and the existing Graf’s addition theorem is only suitable for the former.By performing a new replacement between the two coordinates,the exterior transform formula is fi rst deduced.It is then combined with Graf’s addition theorem to establish a whole-space transform formula.By using the whole-space transform formula,the scattering solutions by the sources outside and inside a cylindrical cavity are constructed as examples of its application.The effectiveness and advantages of the whole-space transform formula is illustrated by comparison with the approximate model based on a large cycle method.The whole-space transform formula presented herein can be used to perform the transform between two different cylindrical coordinates in the whole space.In addition,its concept and principle are universal and can be further extended to establish the coordinate transform formula of wave functions in other coordinate systems.展开更多
The conversion of energy between seismic and electromagnetic wave fields has been described by Pride's coupled equations in porous media. In this paper, the seismoelectric field excited by the explosive point sour...The conversion of energy between seismic and electromagnetic wave fields has been described by Pride's coupled equations in porous media. In this paper, the seismoelectric field excited by the explosive point source located at the outside of the borehole is studied. The scattering fields inside and outside a borehole are analyzed and deduced under the boundary conditions at the interface between fluid and porous media. The influences of the distance of the point source, multipole components of the eccentric explosive source, and the receiving position along the axis of vertical borehole, on the converted waves inside the borehole are all investigated. When the distance from the acoustic source to the axis of a borehole is far enough, the longitudinal and coseismic longitudinal wave packets dominate the acoustic and electric field, respectively. The three components of both electric field and magnetic field can be detected, and the radial electric field is mainly excited and converted by the dipole component. Owing to the existence of borehole, the electric fields and magnetic fields in the borehole are azimuthal. The distance from the point where the maximum amplitude of the axial components of electric field is recorded, to the origin of coordinate indicates the horizontal distance from the explosive source to the axis of vertical borehole.展开更多
Purpose To propose a method for simultaneous fluorescence and Compton scattering computed tomography by using linearly polarized X-rays.Methods Monte Carlo simulations were adopted to demonstrate the feasibility of th...Purpose To propose a method for simultaneous fluorescence and Compton scattering computed tomography by using linearly polarized X-rays.Methods Monte Carlo simulations were adopted to demonstrate the feasibility of the proposed method.In the simulations,the phantom is a polytetrafluoroethylene cylinder inside which are cylindrical columns containing aluminum,water,and gold(Au)-loaded water solutions with Au concentrations ranging between 0.5 and 4.0 wt%,and a parallel-hole collimator imaging geometry was adopted.The light source was modeled based on a Thomson scattering X-ray source.The phantom images for both imaging modalities were reconstructed using a maximumlikelihood expectation maximization algorithm.Results Both the X-ray fluorescence computed tomography(XFCT)and Compton scattering computed tomography(CSCT)images of the phantom were accurately reconstructed.A similar attenuation contrast problem for the different cylindrical columns in the phantom can be resolved in the XFCT and CSCT images.The interplay between XFCT and CSCT was analyzed,and the contrast-to-noise ratio(CNR)of the reconstruction was improved by correcting for the mutual influence between the two imaging modalities.Compared with K-edge subtraction imaging,XFCT exhibits a CNR advantage for the phantom.Conclusion Simultaneous XFCT and CSCT can be realized by using linearly polarized X-rays.The synergy between the two imaging modalities would have an important application in cancer radiation therapy.展开更多
At thermal ultra-cold neutron (UCN) sources (neutrons in thermal equilibrium with the moderator) only a very small fraction of neutrons have velocities ~6 m/s. Therefore, the UCN production rate cannot be substantiall...At thermal ultra-cold neutron (UCN) sources (neutrons in thermal equilibrium with the moderator) only a very small fraction of neutrons have velocities ~6 m/s. Therefore, the UCN production rate cannot be substantially increased by simply lowering the temperature of the moderator. The new approach is to use the super-thermal principle, i.e., neutrons not in thermal equilibrium with the converter. We want to investigate scattering kernels for a super-thermal UCN source based on a two-layer arrangement of D2O and solid D2. The solid D2 (sD2) at temperature 8 K is kept in close contact with D2O moderator at room temperature. Using the MCNP code, the fast neutron flux on the spallation target, the thermal flux in the D2O near the sD2, and the cold flux in the sD2 are simulated. For a given cold flux, neutron transport equations are calculated. In order to obtain precise neutron scattering kernels, and consequently UCN flux and density, 330 neutron energy groups have been taken. The coupled energy dependent transport equations have been solved by combining MCNPX code with an analytical approach and using implicit method in MATLAB. We have obtained an optimal dimension for the UCN source. A suitable space step has been taken for the numerical stability.展开更多
The parasitic source resistance（RS） of AlGaN/AlN/GaN heterostructure field-effect transistors（HFETs） is studied in the temperature range 300–500 K. By using the measured RSand both capacitance–voltage（C–V） an...The parasitic source resistance（RS） of AlGaN/AlN/GaN heterostructure field-effect transistors（HFETs） is studied in the temperature range 300–500 K. By using the measured RSand both capacitance–voltage（C–V） and current–voltage（I–V） characteristics for the fabricated device at 300, 350, 400, 450, and 500 K, it is found that the polarization Coulomb field（PCF） scattering exhibits a significant impact on RSat the above-mentioned different temperatures. Furthermore, in the AlGaN/AlN/GaN HFETs, the interaction between the additional positive polarization charges underneath the gate contact and the additional negative polarization charges near the source Ohmic contact, which is related to the PCF scattering, is verified during the variable-temperature study of RS.展开更多
High brightness γ-rays produced by laser Compton scattering(LCS) are ideal probes for the study of nucleon and nuclear structure. We propose such a γ-ray source using the backscattering of a laser from the bright el...High brightness γ-rays produced by laser Compton scattering(LCS) are ideal probes for the study of nucleon and nuclear structure. We propose such a γ-ray source using the backscattering of a laser from the bright electron beam produced by the linac of the Shanghai Soft X-ray Free-electron Laser(SXFEL) test facility at the Shanghai Institute of Applied Physics(SINAP). The performance is optimized through theoretical analysis and benchmarked with 4D Monte-Carlo simulations. The peak brightness of the source is expected to be larger than2 × 1022photons/(mm2mrad2s 0.1%BW) and photon energy ranges from 3.7 Me V to 38.9 Me V. Its performance, compared to Extreme Light Infrastructure-Nuclear Physics(ELI-NP), and the Shanghai Laser-Electron Gamma-ray Source(SLEGS), is given. The potential for basic and applied research is also briefly outlined.展开更多
Increasing the peak brightness is beneficial to various applications of the Thomson scattering X-ray source. A higher peak brightness of the scattered X-ray pulse demands a shorter scattering electron beam realized by...Increasing the peak brightness is beneficial to various applications of the Thomson scattering X-ray source. A higher peak brightness of the scattered X-ray pulse demands a shorter scattering electron beam realized by beam compression in the electron beam-line. In this article, we study the possibility of compressing the electron beam in a typical S-band normal conducting photo-injector via ballistic bunching, through just adding a short RF linac section right behind the RF gun, so as to improve the peak brightness of the scattered x-ray pulse. Numerical optimization by ASTRA demonstrates that the peak current can increase from 50 A to 300 A for a 500 pC, 10 ps FWHM electron pulse, while normalized transverse RMS emittance and RMS energy spread increases very little. Correspondingly, the peak brightness of the Thomson scattering X-ray source is estimated to increase about three times.展开更多
基金co-supported by the National Natural Science Foundation of China(Nos.61201320,61371023)the Fundamental Research Funds for the Central Universities of China(No.3102014JCQ01103)
文摘The radar cross section （RCS） of weak scattering source on the surface of an aircraft is usually less than -40 dBsm. How to accurately measure the RCS characteristics of weak scattering source is a technical challenge for the aircraft＇s RCS measurement. This paper proposes separating and extracting the two-dimensional （2D） reflectivity distribution of the weak scattering source with the microwave imaging algorithm and spectral transform so as to enhance its measurement preci- sion. Firstly, we performed the 2D microwave imaging of the target and then used the 2D gating function to separate and extract the reflectivity distribution of the weak scattering source. Secondly, we carried out the spectral transform of the reflectivity distribution and eventually obtained the RCS of the weak scattering source through calibration. The prototype experimental results and their analysis show that the measurement method is effective. The experiments on an aircraft＇s low-scattering conformal antenna verify that the measurement method can eliminate the clutter on the surface of aircraft. The precision of measuring a -40 dBsm target is 3 5 dB better than the existing RCS measurement methods. The measurement method can more accurately obtain the weak scattering source＇s RCS characteristics.
基金This work was supported by the National Natural Science Foundation of China(Grant Nos.11535006,11991071,11775125,and 11875175)the Tsinghua University Initiative Scientific Research Program.
文摘Micro-focus computed tomography(CT),which allows the hyperfine structure within objects to be reconstructed,is a powerful nondestructive testing tool in many fields.However,current x-ray sources for micro-focus CT are typically limited by their relatively low photon energy and low flux.An all-optical inverse Compton scattering source(AOCS)based on laser wakefield acceleration can generate intense quasi-monoenergetic x/gamma-ray pulses in the kilo-to megaelectronvolt range with micrometer-level source size,and its potential application for micro-focus CT has become very attractive in recent years because of the rapid progress made in laser wakefield acceleration.Reported here is a successful experimental demonstration of high-fidelity micro-focus CT using an AOCS(∼70 keV)by imaging and reconstructing a test object with complex inner structures.A region-of-interest CT method is adopted to utilize the relatively small field of view of the AOCS to ensure high spatial resolution.This demonstration of AOCS-based region-of-interest micro-focus CT is a key step toward its application in the field of hyperfine nondestructive testing.
基金Supported by the National Natural Science Foundation of China under Grant Nos.10371070,10671121the Foundation of Shanghai Education Committee for Shanghai Prospective Excellent Young Teachers+1 种基金Shanghai Leading Academic Discipline Project under Grant No.J50101 the President Foundation of East China Institute of Technology under Grant No.DHXK0810
文摘N-soliton solutions of the hierarchy of non-isospectral mKdV equation with self-consistent sources andthe hierarchy of non-isospectral sine-Gordon equation with self-consistent sources are obtained via the inverse scatteringtransform.
基金Supported by the National Natural Science Foundation of China under Grant No.51279033Heilongjiang Natural Science Foundation of China under Grant No.F201346
文摘Separation of the components of rigid acoustic scattering by underwater objects is essential in obtaining the structural characteristics of such objects. To overcome the problem of rigid structures appearing to have the same spectral structure in the time domain, time-frequency Blind Source Separation (BSS) can be used in combination with image morphology to separate the rigid scattering components of different objects. Based on a highlight model, the separation of the rigid scattering structure of objects with time-frequency distribution is deduced. Using a morphological filter, different characteristics in a Wigner-Ville Distribution (WVD) observed for single auto term and cross terms can be simplified to remove any cross-term interference. By selecting time and frequency points of the auto terms signal, the accuracy of BSS can be improved. A simulation experimental has been used to analyze the feasibility of the new method, with changing the pulse width of the transmitted signal, the relative amplitude and the time delay parameter. And simulation results show that the new method can not only separate rigid scattering components, but can also separate the components when elastic scattering and rigid scattering exist at the same time. Experimental results confirm that the new method can be used in separating the rigid scattering structure of underwater objects.
基金The project supported by National Natural Science Foundation of China under Grant Nos.10371070 and 10671121the Foundation of Shanghai Education Committee for Shanghai Prospective Excellent Young Teachers
文摘This paper investigates in detail the dynamics of the modified KdV equation with self-consistent sources, including characteristics of one-soliton, scattering conditions and phase shifts of two solitons, degenerate case of two solitons and ＂ghost＂ solitons, etc. Co-moving coordinate frames are employed in asymptotic analysis.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.10902010 and 10975121)the Foundation of China Academy of Engineering Physics(CAEP)(Grant No.2009A0102003)the Foundation of Laboratory of Science and Technology on Plasma Physics,RCLF,CAEP(Grant No.9140C680305120C68252)
文摘Energy spectra, angular distributions, and temporal profiles of the photons produced by an all-optical Thomson scat- tering X-ray source are explored through numerical simulations based on the parameters of the SILEX-I laser system （800 nm, 30 fs, 300 TW） and the previous wakefield acceleration experimental results. The simulation results show that X-ray pulses with a duration of 30 fs and an emission angle of 50 mrad can be produced from such a source. Using the optimized electron parameters, X-ray pulses with better directivity and narrower energy spectra can be obtained. Besides the electron parameters, the laser parameters such as the wavelength, pulse duration, and spot size also affect the X-ray yield, the angular distribution, and the maximum photon energy, except the X-ray pulse duration which is slightly changed for the case of ultrafast laser-electron interaction.
文摘In this paper, it is proved the ability of quantity reconstruction, amplitudes and coordinates of metallic strip local scattering sources from the backscattering pattern. They are performed as the results of numerical solution for the infinite perfect conducting strip in case of E-polarization of the incident plane electromagnetic wave. In this case it is necessary to fulfill the following conditions. The local sources amplitudes should be the same order, in transverse and longitudinal directions the local sources should be separated into distances more than apparatus resolution, and the object maximum size does not have to be more than approximately 50λ. It was shown the limit and ability of the further development of the offered method.
基金supported by National Natural Science Foundation of China(NSFC)(Nos.12005211,11905210,11975218 and 11805192).
文摘We report our recent progress in the design and simulation of a high-brightness S-band photo-injector with a ballistic bunching scheme aimed at driving an inverse Compton scattering(ICS)X-ray source.By adding a short standing-wave buncher between the RF gun and first booster in a conventional S-band photo-injector,electron bunches with a 500 pC charge can be compressed to the sub-picosecond level with very limited input RF power and an unchanged basic layout of the photo-injector.Beam dynamics analysis indicates that fine tuning of the focusing strength of the gun and linac solenoid can well balance additional focusing provided by the standing wave buncher and generate a well-compensated transverse emittance.Thorough bunching dynamics simulations with different operating conditions of the buncher show that a buncher with more cells and a moderate gradient is suitable for simultaneously obtaining a short bunch duration and low emittance.In a typical case of a 9-cell buncher with a 38 MV/m gradient,an ultrashort bunch duration of 0.5 ps(corresponding to a compression ratio of>5)and a low emittance of<1 mm mrad can be readily obtained for a 500 pC electron pulse.This feasible ballistic bunching scheme will facilitate the implementation of an ultrashort pulse mode inverse Compton scattering X-ray source on most existing S-band photo-injectors.
文摘The inverse scattering problems are to detect the property of obstacles from the measurements outside the obstacles. One of important research areas in this topic is the recovery of boundary property for impenetrable obstacles. In this paper, we would like to give a brief review about the recently developed singular source methods. There are three different methods in this category, namely, linear sampling method, pointsource method and probe method. We also present some recent new results about the probe method.
基金supported by National Natural Science Foundation of China(12374358,91950207)Guangdong Basic and Applied Basic Research Foundation(2024A1515010420).
文摘Glucose molecules are of great significance being one of the most important molecules in metabolic chain.However,due to the small Raman scattering cross-section and weak/non-adsorption on bare metals,accurately obtaining their"fingerprint information"remains a huge obstacle.Herein,we developed a tip-enhanced Raman scattering(TERS)technique to address this challenge.Adopting an optical fiber radial vector mode internally illuminates the plasmonic fiber tip to effectively suppress the background noise while generating a strong electric-field enhanced tip hotspot.Furthermore,the tip hotspot approaching the glucose molecules was manipulated via the shear-force feedback to provide more freedom for selecting substrates.Consequently,our TERS technique achieves the visualization of all Raman modes of glucose molecules within spectral window of 400-3200 cm^(-1),which is not achievable through the far-field/surface-enhanced Raman,or the existing TERS techniques.Our TERS technique offers a powerful tool for accurately identifying Raman scattering of molecules,paving the way for biomolecular analysis.
基金supported by the Anhui Provincial Major Science and Technology Project(No.201903c08020003)the Taishan industrial Experts Program。
文摘The application of a controllable neutron source for measuring formation porosity in the advancement of nuclear logging has garnered increased attention.The existing porosity algorithm,which is based on the thermal neutron counting ratio,exhibits lower sensitivity in high-porosity regions.To enhance the sensitivity,the effects of elastic and inelastic scattering,which influence the slowing-down of fast neutrons,were theoretically analyzed,and a slowing-down model of fast neutrons was created.Based on this model,a density correction porosity algorithm was proposed based on the relationship between density,thermal neutron counting ratio,and porosity.Finally,the super multifunctional calculation program for nuclear design and safety evaluation(TopMC/SuperMC)was used to create a simulation model for porosity logging,and its applicability was examined.The results demonstrated that the relative error between the calculated and actual porosities was less than 1%,and the influence of deviation in the density measurement was less than 2%.Therefore,the proposed density correction algorithm based on the slowing-down model of fast neutrons can effectively improve the sensitivity in the high-porosity region.This study is expected to serve as a reference for the application of neutron porosity measurements with D–T neutron sources.
基金supported by the National Natural Science Foundation of China(Nos.11505059,11575061)the Fundamental Research Funds for Central Universities(No.2017XS087)
文摘In neutron and photon transport problems,anisotropic scattering is of great importance for the particle flux,especially when the angular flux has a strong forward peak in shielding analyses.The conventional Legendre expansion is widely used in discrete ordinates transport codes because of algebraic simplifications with spherical harmonics for the scattering source.However,negative cross sections caused by the finitely truncated expansion may give rise to a negative source and flux.A simple method is adopted,based on integrating functions of scattering moments,to evaluate anisotropy and convergence of expanded functions.A series of problems were designed with angular fluxes of different anisotropy,and numerical simulations were performed using the ARES transport code to study different treatments and algorithms for scattering.Results show that the diagonal transport approximation is more stable and obtains a similar accuracy with the extended approximation.A conservative fixup for the negative source could ensure particle balance and improve computational accuracy significantly for photon transport.The effect of anisotropic scattering is problem-dependent,and no distinct differences among various methods are observed for volume source problems with a continuous energy source.For beam source problems,flux results are sensitive to negative scattering functions,and strictly nonnegative cross sections need to be implemented.
基金Supported by the Research Foundation of Education Bureau of Jiangxi Province of China under Grant No.GJJ13459the National Natural Science Foundation of China under Grant No.11101350
文摘In the paper, Ablowitz–Ladik hierarchy with new self-consistent sources is investigated. First the source in the hierarchy is described as φnφn+1, where φnis related to the Ablowitz–Ladik spectral problem, instead of the corresponding adjoint spectral problem. Then by means of the inverse scattering transform, the multi-soliton solutions for the hierarchy are obtained. Two reductions to the discrete mKdV and nonlinear Schr¨odinger hierarchies with selfconsistent sources are considered by using the uniqueness of the Jost functions, as well as their N-soliton solutions.
基金the National Natural Science Foundation of China under Grand No.549974011
文摘The theory of elastic wave scattering is a fundamental concept in the study of elastic dynamics and wave motion,and the wave function expansion technique has been widely used in many subjects.To supply the essential tools for solving wave scattering problems induced by an eccentric source or multi-sources as well as multi-scatters,a whole-space transform formula of cylindrical wave functions is presented and its applicability to some simple cases is demonstrated in this study.The transforms of wave functions in cylindrical coordinates can be classifi ed into two basic types: interior transform and exterior transform,and the existing Graf’s addition theorem is only suitable for the former.By performing a new replacement between the two coordinates,the exterior transform formula is fi rst deduced.It is then combined with Graf’s addition theorem to establish a whole-space transform formula.By using the whole-space transform formula,the scattering solutions by the sources outside and inside a cylindrical cavity are constructed as examples of its application.The effectiveness and advantages of the whole-space transform formula is illustrated by comparison with the approximate model based on a large cycle method.The whole-space transform formula presented herein can be used to perform the transform between two different cylindrical coordinates in the whole space.In addition,its concept and principle are universal and can be further extended to establish the coordinate transform formula of wave functions in other coordinate systems.
基金Project supported by the National Natural Science Foundation of China （Grant Nos. 40974067. 11134011, and 41004044）, the State Key Laboratory of Acoustics, Chinese Academy of Sciences （Grant No. SKLOA201108）, and the Scientific Forefront and Interdisciplinary Innovation Project of Jilin University, China.
文摘The conversion of energy between seismic and electromagnetic wave fields has been described by Pride's coupled equations in porous media. In this paper, the seismoelectric field excited by the explosive point source located at the outside of the borehole is studied. The scattering fields inside and outside a borehole are analyzed and deduced under the boundary conditions at the interface between fluid and porous media. The influences of the distance of the point source, multipole components of the eccentric explosive source, and the receiving position along the axis of vertical borehole, on the converted waves inside the borehole are all investigated. When the distance from the acoustic source to the axis of a borehole is far enough, the longitudinal and coseismic longitudinal wave packets dominate the acoustic and electric field, respectively. The three components of both electric field and magnetic field can be detected, and the radial electric field is mainly excited and converted by the dipole component. Owing to the existence of borehole, the electric fields and magnetic fields in the borehole are azimuthal. The distance from the point where the maximum amplitude of the axial components of electric field is recorded, to the origin of coordinate indicates the horizontal distance from the explosive source to the axis of vertical borehole.
基金supported by the National Natural Science Foundation of China(Nos.12375157,12027902,and 11905011)。
文摘Purpose To propose a method for simultaneous fluorescence and Compton scattering computed tomography by using linearly polarized X-rays.Methods Monte Carlo simulations were adopted to demonstrate the feasibility of the proposed method.In the simulations,the phantom is a polytetrafluoroethylene cylinder inside which are cylindrical columns containing aluminum,water,and gold(Au)-loaded water solutions with Au concentrations ranging between 0.5 and 4.0 wt%,and a parallel-hole collimator imaging geometry was adopted.The light source was modeled based on a Thomson scattering X-ray source.The phantom images for both imaging modalities were reconstructed using a maximumlikelihood expectation maximization algorithm.Results Both the X-ray fluorescence computed tomography(XFCT)and Compton scattering computed tomography(CSCT)images of the phantom were accurately reconstructed.A similar attenuation contrast problem for the different cylindrical columns in the phantom can be resolved in the XFCT and CSCT images.The interplay between XFCT and CSCT was analyzed,and the contrast-to-noise ratio(CNR)of the reconstruction was improved by correcting for the mutual influence between the two imaging modalities.Compared with K-edge subtraction imaging,XFCT exhibits a CNR advantage for the phantom.Conclusion Simultaneous XFCT and CSCT can be realized by using linearly polarized X-rays.The synergy between the two imaging modalities would have an important application in cancer radiation therapy.
文摘At thermal ultra-cold neutron (UCN) sources (neutrons in thermal equilibrium with the moderator) only a very small fraction of neutrons have velocities ~6 m/s. Therefore, the UCN production rate cannot be substantially increased by simply lowering the temperature of the moderator. The new approach is to use the super-thermal principle, i.e., neutrons not in thermal equilibrium with the converter. We want to investigate scattering kernels for a super-thermal UCN source based on a two-layer arrangement of D2O and solid D2. The solid D2 (sD2) at temperature 8 K is kept in close contact with D2O moderator at room temperature. Using the MCNP code, the fast neutron flux on the spallation target, the thermal flux in the D2O near the sD2, and the cold flux in the sD2 are simulated. For a given cold flux, neutron transport equations are calculated. In order to obtain precise neutron scattering kernels, and consequently UCN flux and density, 330 neutron energy groups have been taken. The coupled energy dependent transport equations have been solved by combining MCNPX code with an analytical approach and using implicit method in MATLAB. We have obtained an optimal dimension for the UCN source. A suitable space step has been taken for the numerical stability.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11174182,11574182,and 61306113)the Specialized Research Fund for the Doctoral Program of Higher Education of China(Grant No.20110131110005)
文摘The parasitic source resistance（RS） of AlGaN/AlN/GaN heterostructure field-effect transistors（HFETs） is studied in the temperature range 300–500 K. By using the measured RSand both capacitance–voltage（C–V） and current–voltage（I–V） characteristics for the fabricated device at 300, 350, 400, 450, and 500 K, it is found that the polarization Coulomb field（PCF） scattering exhibits a significant impact on RSat the above-mentioned different temperatures. Furthermore, in the AlGaN/AlN/GaN HFETs, the interaction between the additional positive polarization charges underneath the gate contact and the additional negative polarization charges near the source Ohmic contact, which is related to the PCF scattering, is verified during the variable-temperature study of RS.
基金Supported by the Major State Basic Research Development Program of China(No.2011CB808300)the Shanghai Natural Science Foundation(No.13ZR1464700)the Knowledge Innovation Project of the Chinese Academy of Sciences(No.255015061)
文摘High brightness γ-rays produced by laser Compton scattering(LCS) are ideal probes for the study of nucleon and nuclear structure. We propose such a γ-ray source using the backscattering of a laser from the bright electron beam produced by the linac of the Shanghai Soft X-ray Free-electron Laser(SXFEL) test facility at the Shanghai Institute of Applied Physics(SINAP). The performance is optimized through theoretical analysis and benchmarked with 4D Monte-Carlo simulations. The peak brightness of the source is expected to be larger than2 × 1022photons/(mm2mrad2s 0.1%BW) and photon energy ranges from 3.7 Me V to 38.9 Me V. Its performance, compared to Extreme Light Infrastructure-Nuclear Physics(ELI-NP), and the Shanghai Laser-Electron Gamma-ray Source(SLEGS), is given. The potential for basic and applied research is also briefly outlined.
基金Supported by National Natural Science Foundation of China(11127507,11375097,11375098)National Basic Research Program of China(973 Program)(2011CB808302)
文摘Increasing the peak brightness is beneficial to various applications of the Thomson scattering X-ray source. A higher peak brightness of the scattered X-ray pulse demands a shorter scattering electron beam realized by beam compression in the electron beam-line. In this article, we study the possibility of compressing the electron beam in a typical S-band normal conducting photo-injector via ballistic bunching, through just adding a short RF linac section right behind the RF gun, so as to improve the peak brightness of the scattered x-ray pulse. Numerical optimization by ASTRA demonstrates that the peak current can increase from 50 A to 300 A for a 500 pC, 10 ps FWHM electron pulse, while normalized transverse RMS emittance and RMS energy spread increases very little. Correspondingly, the peak brightness of the Thomson scattering X-ray source is estimated to increase about three times.
