The Infrared Hyperspectral Atmospheric SounderⅡ(HIRAS-Ⅱ)is the key equipment on FengYun-3E(FY-3E)satellite,which can realize vertical atmospheric detection,featuring hyper spectral,high sensitivity and high precisio...The Infrared Hyperspectral Atmospheric SounderⅡ(HIRAS-Ⅱ)is the key equipment on FengYun-3E(FY-3E)satellite,which can realize vertical atmospheric detection,featuring hyper spectral,high sensitivity and high precision.To ensure its accuracy of detection,it is necessary to correlate their thermal models to in-orbit da⁃ta.In this work,an investigation of intelligent correlation method named Intelligent Correlation Platform for Ther⁃mal Model(ICP-TM)was established,the advanced Kriging surrogate model and efficient adaptive region opti⁃mization algorithm were introduced.After the correlation with this method for FY-3E/HIRAS-Ⅱ,the results indi⁃cate that compared with the data in orbit,the error of the thermal model has decreased from 5 K to within±1 K in cold case(10℃).Then,the correlated model is validated in hot case(20℃),and the correlated model exhibits good universality.This correlation precision is also much superiors to the general ones like 3 K in other similar lit⁃erature.Furthermore,the process is finished in 8 days using ICP-TM,the efficiency is much better than 3 months based on manual.The results show that the proposed approach significantly enhances the accuracy and efficiency of thermal model,this contributes to the precise thermal control of subsequent infrared optical payloads.展开更多
As the proportion of newenergy increases,the traditional cumulant method(CM)produces significant errorswhen performing probabilistic load flow(PLF)calculations with large-scale wind power integrated.Considering the wi...As the proportion of newenergy increases,the traditional cumulant method(CM)produces significant errorswhen performing probabilistic load flow(PLF)calculations with large-scale wind power integrated.Considering the wind speed correlation,a multi-scenario PLF calculation method that combines random sampling and segmented discrete wind farm power was proposed.Firstly,based on constructing discrete scenes of wind farms,the Nataf transform is used to handle the correlation between wind speeds.Then,the random sampling method determines the output probability of discrete wind power scenarios when wind speed exhibits correlation.Finally,the PLF calculation results of each scenario areweighted and superimposed following the total probability formula to obtain the final power flow calculation result.Verified in the IEEE standard node system,the absolute percent error(APE)for the mean and standard deviation(SD)of the node voltages and branch active power are all within 1%,and the average root mean square(AMSR)values of the probability curves are all less than 1%.展开更多
The fatigue of heavy-haul railway bridges is considered a key concern due to high stress levels and cyclic loading.The evaluation of fatigue reliability is required to include factor correlations.A major challenge is ...The fatigue of heavy-haul railway bridges is considered a key concern due to high stress levels and cyclic loading.The evaluation of fatigue reliability is required to include factor correlations.A major challenge is presented by the construction of the cumulative distribution function(CDF)and the description of correlations between random variables.In this study,the copula function is used to analyze the fatigue failure probability of the Shuohuang heavy-haul railway bridge.A C-vine copula(CVC)-based joint probability density function(JPDF)is derived with eight correlated parameters.To enhance efficiency in small failure probability calculations,the subset simulation and most probable point(MPP)Monte Carlo importance sampling are introduced based on the Rosenblatt transform and C-vine model.Comparisons with traditional Monte Carlo methods confirm that high accuracy and efficiency are achieved.The results show that when parameter correlations are ignored,failure probability is underestimated,increasing safety risks in bridge assessments.展开更多
Creating conditions to implement equilibrium processes of damage accumulation under a predictable scenario enables control over the failure of structural elements in critical states.It improves safety and reduces the ...Creating conditions to implement equilibrium processes of damage accumulation under a predictable scenario enables control over the failure of structural elements in critical states.It improves safety and reduces the probability of catastrophic behavior in case of accidents.Equilibrium damage accumulation in some cases leads to a falling part(called a postcritical stage)on the material’s stress-strain curve.It must be taken into account to assess the strength and deformation limits of composite structures.Digital image correlation method,acoustic emission(AE)signals recording,and optical microscopy were used in this paper to study the deformation and failure processes of an orthogonal-layup composite during tension in various directions to orthotropy axes.An elastic-plastic deformation model was proposed for the composite in a plane stress condition.The evolution of strain fields and neck formation were analyzed.The staging of the postcritical deformation process was described.AE signals obtained during tests were studied;characteristic damage types of a material were defined.The rationality and necessity of polymer composites’postcritical deformation stage taken into account in refined strength analysis of structures were concluded.展开更多
For the observed line at 799.23°A in tungsten EBIT experiment,which was assigned to be^(3)F_(4)^(o)−^(3)F_(3)^(o)([Ar]4s^(2)4p^(5)4d)of W^(38+)ion,there were noticeable deviations for most calculated wavelengths ...For the observed line at 799.23°A in tungsten EBIT experiment,which was assigned to be^(3)F_(4)^(o)−^(3)F_(3)^(o)([Ar]4s^(2)4p^(5)4d)of W^(38+)ion,there were noticeable deviations for most calculated wavelengths from the measured value.To clarify this issue,we carry out an extensive calculation for energy levels and transition properties of W^(38+)ion using the multi-configuration Dirac–Hartree–Fock and relativistic configuration interaction method,in which more deeper inner core electron correlations are included,and different forms of Breit interaction as well as quantum electrodynamics corrections are investigated.It is found that the inner core electron correlations can affect the total energy of levels,while only slightly modify the excited energy of levels in 4s^(2)4p^(5)4d complex.The present calculated wavelengths agree with the corresponding measured values excellently except the line at 799.23Å.Thus we are strongly suspicious this line should be misidentified,and suggest that new experiment with higher resolution and spectra analysis based on more accurate atomic data should be performed for W^(38+)ion.展开更多
Estimation precision of Displaced Phase Center Algorithm(DPCA) is affected by the number of displaced phase center pairs,the bandwidth of transmitting signal and many other factors.Detailed analysis is made on DPCA...Estimation precision of Displaced Phase Center Algorithm(DPCA) is affected by the number of displaced phase center pairs,the bandwidth of transmitting signal and many other factors.Detailed analysis is made on DPCA's estimation precision.Analysis results show that the directional vector estimation precision of DPCA is low,which will produce accumulating errors when phase cen-ters' track is estimated.Because of this reason,DPCA suffers from accumulating errors seriously.To overcome this problem,a method combining DPCA with Sub Aperture Image Correlation(SAIC) is presented.Large synthetic aperture is divided into sub-apertures.Micro errors in sub-aperture are estimated by DPCA and compensated to raw echo data.Bulk errors between sub-apertures are esti-mated by SAIC and compensated directly to sub-aperture images.After that,sub-aperture images are directly used to generate ultimate SAS image.The method is applied to the lake-trial dataset of a 20 kHz SAS prototype system.Results show the method can successfully remove the accumulating error and produce a better SAS image.展开更多
We analyzed the infrared 0R）-near infrared （NIR） 2D correlation spectra of drugs perturbed by temperature. By identification of functional groups by IR spectrum and by the correlation analysis of IR-NIR spectrum, w...We analyzed the infrared 0R）-near infrared （NIR） 2D correlation spectra of drugs perturbed by temperature. By identification of functional groups by IR spectrum and by the correlation analysis of IR-NIR spectrum, we identified the characteristic spectral bands that were closely related to the structure of a drug substance of interest. These characteristic spectral bands were relatively less interfered by other ingredients for analysis by the NIR correlation coefficient method. With these characteristic spectral bands, the accuracy of screening illegally added Sildenafil citrate, Tadalafil and Metforrnin hydrochloride in Chinese patent drugs and healthcare products reached about 90%, which met the requirements of rapid screening.展开更多
The digital speckle correlation method is an important optical metrology for sur- face displacement and strain measurement.With this technique,the whole field deformation in- formation can be obtained by tracking the ...The digital speckle correlation method is an important optical metrology for sur- face displacement and strain measurement.With this technique,the whole field deformation in- formation can be obtained by tracking the geometric points on the speckle images based on a correlation-matching search technique.However,general search techniques suffer from great com- putational complexity in the processing of speckle images with large deformation and the large random errors in the processing of images of bad quality.In this paper,an advanced approach based on genetic algorithms (GA) for correlation-matching search is developed.Benefiting from the abilities of global optimum and parallelism searching of GA,this new approach can complete the correlation-matching search with less computational consumption and at high accuracy.Two experimental results from the simulated speckle images have proved the efficiency of the new approach.展开更多
The deformation field around sub-cracks was calculated using the digital speckle correlation method. First, the uni-axial compression tests on sandstone samples containing a pre- fabricated fracture were made. Photomi...The deformation field around sub-cracks was calculated using the digital speckle correlation method. First, the uni-axial compression tests on sandstone samples containing a pre- fabricated fracture were made. Photomicrographs showing the characteristics of the sub-crack development were taken using a scanning electron microscope （SEM）. From these photomicrographs, the real-time images showing the initiation, growth and coalescence of sub-cracks and micro-cracks in the sandstone specimens were obtained and the effects of loading level as well as grain boundaries on the development of cracks were analyzed. Second, the intensity images of the sandstone specimen surface were captured from the observations of the SEM corresponding to different loading levels. Then correlation computation was carried out for the sequential pairs of intensity images to evaluate the displacement components, as well as the strain field. The results show that the deformation varies in different areas separated by sub-cracks during rock damage processes.展开更多
Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials ...Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials is proposed. First of all, according to the manufacturing process of FDM, orthotropic constitutive model is used to describe the mechanical behavior. Then the virtual fields method(VFM) is applied to characterize all the mechanical parameters(Q, Q, Q, Q) using the full-field strain,which is measured by digital image correlation(DIC). Since the principal axis of the FDM-fabricated structure is sometimes unknown due to the complexity of the manufacturing process, a disk in diametrical compression is used as the load configuration so that the loading angle can be changed conveniently. To verify the feasibility of the proposed method, finite element method(FEM) simulation is conducted to obtain the strain field of the disk. The simulation results show that higher accuracy can be achieved when the loading angle is close to 30?. Finally, a disk fabricated by FDM was used for the experiment. By rotating the disk, several tests with different loading angles were conducted. To determine the position of the principal axis in each test, two groups of parameters(Q, Q, Q, Q) are calculated by two different groups of virtual fields. Then the corresponding loading angle can be determined by minimizing the deviation between two groups of the parameters. After that, the four constants(Q, Q, Q, Q) were determined from the test with an angle of 27?.展开更多
This paper studies the interface curing stresses between polymethyl methacrylate (PMMA) and composite by means of digital speckle correlation method (DSCM).A new method by combining DSCM with the marker points is deve...This paper studies the interface curing stresses between polymethyl methacrylate (PMMA) and composite by means of digital speckle correlation method (DSCM).A new method by combining DSCM with the marker points is developed to measure the interface curing stresses,and the measurement principle is introduced.The interface curing stresses between PMMA and composite with different curing bonding conditions are measured and analyzed,this indicates that the residual stress for furnace heating and furnace cooling is the smallest.Finally,the measurement error is discussed by means of finite element method,the influences of glass microsphere between adhesive and PMMA can be ignored.展开更多
In a test of the weak equivalence principle （WEP） with a rotating torsion pendulum, it is important to estimate the amplitude of the modulation signal with high precision. We use a torsional filter to remove the fre...In a test of the weak equivalence principle （WEP） with a rotating torsion pendulum, it is important to estimate the amplitude of the modulation signal with high precision. We use a torsional filter to remove the free oscillation signal and employ the correlation method to estimate the amplitude of the modulation signal. The data analysis of an experiment shows that the uncertainties of amplitude components of the modulation signal obtained by the correlation method are in agreement with those due to white noise. The power spectral density of the modulation signal obtained by the correlation method is about one order higher than the thermal noise limit. It indicates that the correlation method is an effective way to estimate the amplitude of the modulation signal and it is instructive to conduct a high-accuracy WEP test.展开更多
Aimed at improving the bias stability of Fiber-Optic Gyroscope(FOG)-based inertial navigation systems in environments of various ambient temperatures,a novel temperaturecompensation method based on a correlation analy...Aimed at improving the bias stability of Fiber-Optic Gyroscope(FOG)-based inertial navigation systems in environments of various ambient temperatures,a novel temperaturecompensation method based on a correlation analysis of the same batch of FOGs is proposed.The empirical mode decomposition method was employed to filter the high-frequency noises of the FOGs.Then,the correlation information of the multiple FOGs was used to analyze the feasibility of the method.Eventually,the same residual error of the FOGs was compensated via the simple piecewise linear models.The experimental results indicate that excellent compensation effects for both high-and low-accuracy FOGs are achieved using the proposed method.Specifically,the accuracies of high-accuracy FOGs are improved by approximately 33.9%,20%,and 31.2%,while those of low-accuracy FOGs are improved by approximately 39.1%,20.8%,and 26.1%.The method exhibits the merits of simplicity,validity,and stability,and thus is expected to be widely used in engineering applications.展开更多
The isotropic and anisotropic behaviors are considered as the important formats of the constitutive behaviors,and can also be called the global properties.To improve the identification ability of virtual fields method...The isotropic and anisotropic behaviors are considered as the important formats of the constitutive behaviors,and can also be called the global properties.To improve the identification ability of virtual fields method(VFM)when the global properties are unknown,this paper proposes the strain correlation method(SCM)to determine the global properties before the parameter identification using the VFM.Firstly,the basic principle of SCM is described in detail.Then,the feasibility and accuracy of SCM are verified through the numerical experiments based on the three-point bending configuration and the real experiment of polymethyl methacrylate(PMMA).The influence of the additive Gaussian white noise,local errors in the strain fields,and missing data at the specimen edges on the characterization results are evaluated.The results show that the SCM has good noise immunity and lower accuracy requirements for the strain fields.As an application,the mechanical properties of Ti-6A1-4V alloys fabricated by selective laser melting(SLM)are characterized by the SCM.The results show that the alloys are isotropic,and the isotropic VFM is utilized to determine the mechanical parameters.By using the SCM,the accuracy of identification results can be improved for the isotropic or bidirectional reinforced orthotropic materials when using VFM.展开更多
The splitting test is a competitive alternative method to study the tensile strength of sea ice owing to its suitability for sampling.However,the approach was questioned to the neglect of local plastic deformation dur...The splitting test is a competitive alternative method to study the tensile strength of sea ice owing to its suitability for sampling.However,the approach was questioned to the neglect of local plastic deformation during the tests.In this study,splitting tests were performed on sea ice,with 32 samples subjected to the regular procedure and 8 samples subjected to the digital image correlation method.The salinity,density,and temperature were measured to determine the total porosity.With the advantage of the digital image correlation method,the full-field deformation of the ice samples could be determined.In the loading direction,the samples mainly deformed at the ice-platen contact area.In the direction vertical to the loading,deformation appears along the central line where the splitting crack occurs.Based on the distribution of the sample deformation,a modified solution was derived to calculate the tensile strength with the maximum load.Based on the modified solution,the tensile strength was further calculated together with the splitting test results.The results show that the tensile strength has a negative correlation with the total porosity,which agrees with previous studies based on uniaxial tension tests.展开更多
The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economic...The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economical, less time-consuming, and easily adaptable to the field. The main aim of this study was to derive correlations between direct and indirect test methods for basalt and rhyolite rock types from Carlin trend deposits in Nevada. In the destructive methods, point load index, block punch index, and splitting tensile strength tests are performed. In the non-destructive methods, Schmidt hammer and ultrasonic pulse velocity tests are performed. Correlations between the direct and indirect compression strength tests are developed using linear and nonlinear regression analysis methods. The results show that the splitting tensile strength has the best correlation with the uniaxial compression strength.Furthermore, the Poisson's ratio has no correlation with any of the direct and indirect test results.展开更多
The effects of plasma screening on the ^(1)P^(o) resonance states of H-and He below the n=3 and n=4 thresholds of the respective subsystemsare investigated using the stabilization method and correlated exponential wav...The effects of plasma screening on the ^(1)P^(o) resonance states of H-and He below the n=3 and n=4 thresholds of the respective subsystemsare investigated using the stabilization method and correlated exponential wave functions.Two plasma mediums,namely,the Debye plasma and quantum plasma environments are considered.The screened Coulomb potential(SCP)obtained from Debye-Hückel model is used to represent Debye plasma environments and the exponential cosine screened Coulomb potential(ECSCP)obtained from a modified Debye-Hückel model is used to represent quantum plasma environments.The resonance parameters(resonance positions and widths)are presented in terms of the screening parameters.展开更多
In the measurement of G with the angular acceleration method,the improved correlation method developed by Wu et al.（Wu W H,Tian Y,Luo J,Shao C G,Xu J H and Wang DH 2016 Rev.Sci.Instrum.87 094501） is used to accurate...In the measurement of G with the angular acceleration method,the improved correlation method developed by Wu et al.（Wu W H,Tian Y,Luo J,Shao C G,Xu J H and Wang DH 2016 Rev.Sci.Instrum.87 094501） is used to accurately estimate the amplitudes of the prominent harmonic components of the gravitational background signal with time-varying frequency.Except the quadratic slow drift,the angular frequency of the gravitational background signal also includes a cosine oscillation coming from the useful angular acceleration signal,which leads to a deviation from the estimated amplitude.We calculate the correction of the cosine oscillation to the amplitude estimation.The result shows that the corrections of the cosine oscillation to the amplitudes of the fundamental frequency and second harmonic components obtained by the improved correlation method are within respective errors.展开更多
The validity of correlation analysis between finite element model（FEM） and modal test data is strongly affected by three factors, i.e., quality of excitation and measurement points in modal test,FEM reduction method...The validity of correlation analysis between finite element model（FEM） and modal test data is strongly affected by three factors, i.e., quality of excitation and measurement points in modal test,FEM reduction methods, and correlation check techniques. A new criterion based on modified mode participation（MMP） for choosing the best excitation point is presented. Comparison between this new criterion and mode participation（MP） criterion is made by using Case 1 with a simple printed circuit board（PCB）. The result indicates that this new criterion produces better results. In Case 2, 35 measurement points are selected to perform modal test and correlation analysis while 9 selected in Case 3.System equivalent reduction expansion process（SEREP）, modal assurance criteria（MAC）, coordinate modal assurance criteria（CoMAC）, pseudo orthogonality check（POC） and coordinate orthogonality check（CORTHOG） are used to show the error introduced by modal test in Cases 2 and 3. Case 2 shows that additional errors which cannot be identified by using CoMAC can be found by using CORTHOG.In both Cases 2 and 3, Guyan reduction, improved reduced system（IRS） method, SEREP and Hybrid reduction are compared for accuracy and robustness. The results suggest that the quality of the reduction process is problem dependent. However, the IRS method is an improvement over the Guyan reduction, and the Hybrid reduction is an improvement over the SEREP reduction.展开更多
A new method to measure the average plasma velocity in a Hall-effect thruster is presented. The method is brought forward in virtue of the characteristics of low frequency oscillation induced by the propellant ionizat...A new method to measure the average plasma velocity in a Hall-effect thruster is presented. The method is brought forward in virtue of the characteristics of low frequency oscillation induced by the propellant ionization in the channel and the oriented movement feature of the plasma density out of the channel. The method, equivalent to the correlation method generally used in the signal processing field, provides a solution to the problem of specific impulse measurement on a timescale of hundreds of microseconds and makes the time evolution of average plasma velocity clear. The comparison between the measured value and the calibrated value shows that the relative error is about 3%.展开更多
基金Supported by the National Key Research and Development Program of China(2022YFB3904803)。
文摘The Infrared Hyperspectral Atmospheric SounderⅡ(HIRAS-Ⅱ)is the key equipment on FengYun-3E(FY-3E)satellite,which can realize vertical atmospheric detection,featuring hyper spectral,high sensitivity and high precision.To ensure its accuracy of detection,it is necessary to correlate their thermal models to in-orbit da⁃ta.In this work,an investigation of intelligent correlation method named Intelligent Correlation Platform for Ther⁃mal Model(ICP-TM)was established,the advanced Kriging surrogate model and efficient adaptive region opti⁃mization algorithm were introduced.After the correlation with this method for FY-3E/HIRAS-Ⅱ,the results indi⁃cate that compared with the data in orbit,the error of the thermal model has decreased from 5 K to within±1 K in cold case(10℃).Then,the correlated model is validated in hot case(20℃),and the correlated model exhibits good universality.This correlation precision is also much superiors to the general ones like 3 K in other similar lit⁃erature.Furthermore,the process is finished in 8 days using ICP-TM,the efficiency is much better than 3 months based on manual.The results show that the proposed approach significantly enhances the accuracy and efficiency of thermal model,this contributes to the precise thermal control of subsequent infrared optical payloads.
基金supported by Basic Science Research Program through the National Natural Science Foundation of China(Grant No.61867003).
文摘As the proportion of newenergy increases,the traditional cumulant method(CM)produces significant errorswhen performing probabilistic load flow(PLF)calculations with large-scale wind power integrated.Considering the wind speed correlation,a multi-scenario PLF calculation method that combines random sampling and segmented discrete wind farm power was proposed.Firstly,based on constructing discrete scenes of wind farms,the Nataf transform is used to handle the correlation between wind speeds.Then,the random sampling method determines the output probability of discrete wind power scenarios when wind speed exhibits correlation.Finally,the PLF calculation results of each scenario areweighted and superimposed following the total probability formula to obtain the final power flow calculation result.Verified in the IEEE standard node system,the absolute percent error(APE)for the mean and standard deviation(SD)of the node voltages and branch active power are all within 1%,and the average root mean square(AMSR)values of the probability curves are all less than 1%.
基金Project supported by the National Natural Science Foundation of China(No.52278180)。
文摘The fatigue of heavy-haul railway bridges is considered a key concern due to high stress levels and cyclic loading.The evaluation of fatigue reliability is required to include factor correlations.A major challenge is presented by the construction of the cumulative distribution function(CDF)and the description of correlations between random variables.In this study,the copula function is used to analyze the fatigue failure probability of the Shuohuang heavy-haul railway bridge.A C-vine copula(CVC)-based joint probability density function(JPDF)is derived with eight correlated parameters.To enhance efficiency in small failure probability calculations,the subset simulation and most probable point(MPP)Monte Carlo importance sampling are introduced based on the Rosenblatt transform and C-vine model.Comparisons with traditional Monte Carlo methods confirm that high accuracy and efficiency are achieved.The results show that when parameter correlations are ignored,failure probability is underestimated,increasing safety risks in bridge assessments.
基金This work was supported by the Russian Science Foundation(Grant No.22-19-00765)at the Perm National Research Polytechnic University.
文摘Creating conditions to implement equilibrium processes of damage accumulation under a predictable scenario enables control over the failure of structural elements in critical states.It improves safety and reduces the probability of catastrophic behavior in case of accidents.Equilibrium damage accumulation in some cases leads to a falling part(called a postcritical stage)on the material’s stress-strain curve.It must be taken into account to assess the strength and deformation limits of composite structures.Digital image correlation method,acoustic emission(AE)signals recording,and optical microscopy were used in this paper to study the deformation and failure processes of an orthogonal-layup composite during tension in various directions to orthotropy axes.An elastic-plastic deformation model was proposed for the composite in a plane stress condition.The evolution of strain fields and neck formation were analyzed.The staging of the postcritical deformation process was described.AE signals obtained during tests were studied;characteristic damage types of a material were defined.The rationality and necessity of polymer composites’postcritical deformation stage taken into account in refined strength analysis of structures were concluded.
基金supported by the Science Challenge Project of China Academy of Engineering Physics(CAEP)(Grant No.TZ2018005)the National Natural Science Foundation of China(Grant Nos.12474277,12374259,12104095,12074081,and 12074082).
文摘For the observed line at 799.23°A in tungsten EBIT experiment,which was assigned to be^(3)F_(4)^(o)−^(3)F_(3)^(o)([Ar]4s^(2)4p^(5)4d)of W^(38+)ion,there were noticeable deviations for most calculated wavelengths from the measured value.To clarify this issue,we carry out an extensive calculation for energy levels and transition properties of W^(38+)ion using the multi-configuration Dirac–Hartree–Fock and relativistic configuration interaction method,in which more deeper inner core electron correlations are included,and different forms of Breit interaction as well as quantum electrodynamics corrections are investigated.It is found that the inner core electron correlations can affect the total energy of levels,while only slightly modify the excited energy of levels in 4s^(2)4p^(5)4d complex.The present calculated wavelengths agree with the corresponding measured values excellently except the line at 799.23Å.Thus we are strongly suspicious this line should be misidentified,and suggest that new experiment with higher resolution and spectra analysis based on more accurate atomic data should be performed for W^(38+)ion.
基金Supported by the National High Technology Research and Development Program of China (863 Program, 2007AA 091101)
文摘Estimation precision of Displaced Phase Center Algorithm(DPCA) is affected by the number of displaced phase center pairs,the bandwidth of transmitting signal and many other factors.Detailed analysis is made on DPCA's estimation precision.Analysis results show that the directional vector estimation precision of DPCA is low,which will produce accumulating errors when phase cen-ters' track is estimated.Because of this reason,DPCA suffers from accumulating errors seriously.To overcome this problem,a method combining DPCA with Sub Aperture Image Correlation(SAIC) is presented.Large synthetic aperture is divided into sub-apertures.Micro errors in sub-aperture are estimated by DPCA and compensated to raw echo data.Bulk errors between sub-apertures are esti-mated by SAIC and compensated directly to sub-aperture images.After that,sub-aperture images are directly used to generate ultimate SAS image.The method is applied to the lake-trial dataset of a 20 kHz SAS prototype system.Results show the method can successfully remove the accumulating error and produce a better SAS image.
基金National Key Technology R & D Program-On-site Rapid Identification of Drug Research Project (Grant No. 2008BAI55B06)
文摘We analyzed the infrared 0R）-near infrared （NIR） 2D correlation spectra of drugs perturbed by temperature. By identification of functional groups by IR spectrum and by the correlation analysis of IR-NIR spectrum, we identified the characteristic spectral bands that were closely related to the structure of a drug substance of interest. These characteristic spectral bands were relatively less interfered by other ingredients for analysis by the NIR correlation coefficient method. With these characteristic spectral bands, the accuracy of screening illegally added Sildenafil citrate, Tadalafil and Metforrnin hydrochloride in Chinese patent drugs and healthcare products reached about 90%, which met the requirements of rapid screening.
基金Project supported by the National Natural Science Foundation of China(No.19772033)the Research Innovation Fund of Tsinghua University for Ph.D.Candidates(No.092410048).
文摘The digital speckle correlation method is an important optical metrology for sur- face displacement and strain measurement.With this technique,the whole field deformation in- formation can be obtained by tracking the geometric points on the speckle images based on a correlation-matching search technique.However,general search techniques suffer from great com- putational complexity in the processing of speckle images with large deformation and the large random errors in the processing of images of bad quality.In this paper,an advanced approach based on genetic algorithms (GA) for correlation-matching search is developed.Benefiting from the abilities of global optimum and parallelism searching of GA,this new approach can complete the correlation-matching search with less computational consumption and at high accuracy.Two experimental results from the simulated speckle images have proved the efficiency of the new approach.
基金supported by the NaturalScience Foundation of China(contract no.40821062)
文摘The deformation field around sub-cracks was calculated using the digital speckle correlation method. First, the uni-axial compression tests on sandstone samples containing a pre- fabricated fracture were made. Photomicrographs showing the characteristics of the sub-crack development were taken using a scanning electron microscope （SEM）. From these photomicrographs, the real-time images showing the initiation, growth and coalescence of sub-cracks and micro-cracks in the sandstone specimens were obtained and the effects of loading level as well as grain boundaries on the development of cracks were analyzed. Second, the intensity images of the sandstone specimen surface were captured from the observations of the SEM corresponding to different loading levels. Then correlation computation was carried out for the sequential pairs of intensity images to evaluate the displacement components, as well as the strain field. The results show that the deformation varies in different areas separated by sub-cracks during rock damage processes.
基金the financial support from the National Natural Science Foundation of China (Grants 11672153, 11232008, and 11227801)
文摘Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials is proposed. First of all, according to the manufacturing process of FDM, orthotropic constitutive model is used to describe the mechanical behavior. Then the virtual fields method(VFM) is applied to characterize all the mechanical parameters(Q, Q, Q, Q) using the full-field strain,which is measured by digital image correlation(DIC). Since the principal axis of the FDM-fabricated structure is sometimes unknown due to the complexity of the manufacturing process, a disk in diametrical compression is used as the load configuration so that the loading angle can be changed conveniently. To verify the feasibility of the proposed method, finite element method(FEM) simulation is conducted to obtain the strain field of the disk. The simulation results show that higher accuracy can be achieved when the loading angle is close to 30?. Finally, a disk fabricated by FDM was used for the experiment. By rotating the disk, several tests with different loading angles were conducted. To determine the position of the principal axis in each test, two groups of parameters(Q, Q, Q, Q) are calculated by two different groups of virtual fields. Then the corresponding loading angle can be determined by minimizing the deviation between two groups of the parameters. After that, the four constants(Q, Q, Q, Q) were determined from the test with an angle of 27?.
基金supported by the National Basic Research Program (973 Program) of China (2011CB606105)
文摘This paper studies the interface curing stresses between polymethyl methacrylate (PMMA) and composite by means of digital speckle correlation method (DSCM).A new method by combining DSCM with the marker points is developed to measure the interface curing stresses,and the measurement principle is introduced.The interface curing stresses between PMMA and composite with different curing bonding conditions are measured and analyzed,this indicates that the residual stress for furnace heating and furnace cooling is the smallest.Finally,the measurement error is discussed by means of finite element method,the influences of glass microsphere between adhesive and PMMA can be ignored.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11575160,91636221,and 11605065)
文摘In a test of the weak equivalence principle （WEP） with a rotating torsion pendulum, it is important to estimate the amplitude of the modulation signal with high precision. We use a torsional filter to remove the free oscillation signal and employ the correlation method to estimate the amplitude of the modulation signal. The data analysis of an experiment shows that the uncertainties of amplitude components of the modulation signal obtained by the correlation method are in agreement with those due to white noise. The power spectral density of the modulation signal obtained by the correlation method is about one order higher than the thermal noise limit. It indicates that the correlation method is an effective way to estimate the amplitude of the modulation signal and it is instructive to conduct a high-accuracy WEP test.
基金supported by the Young Scientists Fund,China(No.62103021).
文摘Aimed at improving the bias stability of Fiber-Optic Gyroscope(FOG)-based inertial navigation systems in environments of various ambient temperatures,a novel temperaturecompensation method based on a correlation analysis of the same batch of FOGs is proposed.The empirical mode decomposition method was employed to filter the high-frequency noises of the FOGs.Then,the correlation information of the multiple FOGs was used to analyze the feasibility of the method.Eventually,the same residual error of the FOGs was compensated via the simple piecewise linear models.The experimental results indicate that excellent compensation effects for both high-and low-accuracy FOGs are achieved using the proposed method.Specifically,the accuracies of high-accuracy FOGs are improved by approximately 33.9%,20%,and 31.2%,while those of low-accuracy FOGs are improved by approximately 39.1%,20.8%,and 26.1%.The method exhibits the merits of simplicity,validity,and stability,and thus is expected to be widely used in engineering applications.
基金This research was financially supported by the National Key Research and Development Program of China(Grant 2017YFB1103900)the National Science and Technology Major Project(Grant 2017-VI-0003-0073)+1 种基金the National Natural Science Foundation of China(Grant 11672153)Hubei Provincial Major Program of Technological Innovation(Grant 2017AAA121).
文摘The isotropic and anisotropic behaviors are considered as the important formats of the constitutive behaviors,and can also be called the global properties.To improve the identification ability of virtual fields method(VFM)when the global properties are unknown,this paper proposes the strain correlation method(SCM)to determine the global properties before the parameter identification using the VFM.Firstly,the basic principle of SCM is described in detail.Then,the feasibility and accuracy of SCM are verified through the numerical experiments based on the three-point bending configuration and the real experiment of polymethyl methacrylate(PMMA).The influence of the additive Gaussian white noise,local errors in the strain fields,and missing data at the specimen edges on the characterization results are evaluated.The results show that the SCM has good noise immunity and lower accuracy requirements for the strain fields.As an application,the mechanical properties of Ti-6A1-4V alloys fabricated by selective laser melting(SLM)are characterized by the SCM.The results show that the alloys are isotropic,and the isotropic VFM is utilized to determine the mechanical parameters.By using the SCM,the accuracy of identification results can be improved for the isotropic or bidirectional reinforced orthotropic materials when using VFM.
基金This study was supported financially by the National Key Research and Development Program of China(Grant no.2018YFA0605902)the National Natural Science Foundation of China(Grant no.52101300)+1 种基金the Fundamental Research Funds for the Central Universities(Grant no.DUT21LK03)Joint Scientific Research Fund Project of DBJI(Grant no.ICR2102).
文摘The splitting test is a competitive alternative method to study the tensile strength of sea ice owing to its suitability for sampling.However,the approach was questioned to the neglect of local plastic deformation during the tests.In this study,splitting tests were performed on sea ice,with 32 samples subjected to the regular procedure and 8 samples subjected to the digital image correlation method.The salinity,density,and temperature were measured to determine the total porosity.With the advantage of the digital image correlation method,the full-field deformation of the ice samples could be determined.In the loading direction,the samples mainly deformed at the ice-platen contact area.In the direction vertical to the loading,deformation appears along the central line where the splitting crack occurs.Based on the distribution of the sample deformation,a modified solution was derived to calculate the tensile strength with the maximum load.Based on the modified solution,the tensile strength was further calculated together with the splitting test results.The results show that the tensile strength has a negative correlation with the total porosity,which agrees with previous studies based on uniaxial tension tests.
基金CDC/NIOSH for their partial funding of this work
文摘The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economical, less time-consuming, and easily adaptable to the field. The main aim of this study was to derive correlations between direct and indirect test methods for basalt and rhyolite rock types from Carlin trend deposits in Nevada. In the destructive methods, point load index, block punch index, and splitting tensile strength tests are performed. In the non-destructive methods, Schmidt hammer and ultrasonic pulse velocity tests are performed. Correlations between the direct and indirect compression strength tests are developed using linear and nonlinear regression analysis methods. The results show that the splitting tensile strength has the best correlation with the uniaxial compression strength.Furthermore, the Poisson's ratio has no correlation with any of the direct and indirect test results.
基金Supported by the Natural Science Foundation of Heilongjiang Province(LH2024A025)。
文摘The effects of plasma screening on the ^(1)P^(o) resonance states of H-and He below the n=3 and n=4 thresholds of the respective subsystemsare investigated using the stabilization method and correlated exponential wave functions.Two plasma mediums,namely,the Debye plasma and quantum plasma environments are considered.The screened Coulomb potential(SCP)obtained from Debye-Hückel model is used to represent Debye plasma environments and the exponential cosine screened Coulomb potential(ECSCP)obtained from a modified Debye-Hückel model is used to represent quantum plasma environments.The resonance parameters(resonance positions and widths)are presented in terms of the screening parameters.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11575160,11175160,11275075,and 11511130011)
文摘In the measurement of G with the angular acceleration method,the improved correlation method developed by Wu et al.（Wu W H,Tian Y,Luo J,Shao C G,Xu J H and Wang DH 2016 Rev.Sci.Instrum.87 094501） is used to accurately estimate the amplitudes of the prominent harmonic components of the gravitational background signal with time-varying frequency.Except the quadratic slow drift,the angular frequency of the gravitational background signal also includes a cosine oscillation coming from the useful angular acceleration signal,which leads to a deviation from the estimated amplitude.We calculate the correction of the cosine oscillation to the amplitude estimation.The result shows that the corrections of the cosine oscillation to the amplitudes of the fundamental frequency and second harmonic components obtained by the improved correlation method are within respective errors.
基金supported by Science and Technology on Reliability and Environmental Engineering Laboratory,Beihang University
文摘The validity of correlation analysis between finite element model（FEM） and modal test data is strongly affected by three factors, i.e., quality of excitation and measurement points in modal test,FEM reduction methods, and correlation check techniques. A new criterion based on modified mode participation（MMP） for choosing the best excitation point is presented. Comparison between this new criterion and mode participation（MP） criterion is made by using Case 1 with a simple printed circuit board（PCB）. The result indicates that this new criterion produces better results. In Case 2, 35 measurement points are selected to perform modal test and correlation analysis while 9 selected in Case 3.System equivalent reduction expansion process（SEREP）, modal assurance criteria（MAC）, coordinate modal assurance criteria（CoMAC）, pseudo orthogonality check（POC） and coordinate orthogonality check（CORTHOG） are used to show the error introduced by modal test in Cases 2 and 3. Case 2 shows that additional errors which cannot be identified by using CoMAC can be found by using CORTHOG.In both Cases 2 and 3, Guyan reduction, improved reduced system（IRS） method, SEREP and Hybrid reduction are compared for accuracy and robustness. The results suggest that the quality of the reduction process is problem dependent. However, the IRS method is an improvement over the Guyan reduction, and the Hybrid reduction is an improvement over the SEREP reduction.
基金supported by National Natural Science Foundation of China(No.50676026)
文摘A new method to measure the average plasma velocity in a Hall-effect thruster is presented. The method is brought forward in virtue of the characteristics of low frequency oscillation induced by the propellant ionization in the channel and the oriented movement feature of the plasma density out of the channel. The method, equivalent to the correlation method generally used in the signal processing field, provides a solution to the problem of specific impulse measurement on a timescale of hundreds of microseconds and makes the time evolution of average plasma velocity clear. The comparison between the measured value and the calibrated value shows that the relative error is about 3%.
