Achievements are presented for truss models of RC structures developed in previous years: 1. Two constitutive models, biaxial and triaxial, are based on regular trusses, with bars obeying nonlinear uniaxial σ-ε laws...Achievements are presented for truss models of RC structures developed in previous years: 1. Two constitutive models, biaxial and triaxial, are based on regular trusses, with bars obeying nonlinear uniaxial σ-ε laws of material under simulation;both models have been compared with test results and show a dependence of Poisson ratio on curvature of σ-ε law. 2. A truss finite element has been used in the nonlinear static and dynamic analysis of plane RC frames;it has been compared with test results and describes, in a simple way, the formation of plastic hinges. 3. Thanks to the very simple geometry of a truss, the equilibrium equations can be easily written and the stiffness matrix can be easily updated, both with respect to the deformed truss, within each step of a static incremental loading or within each time step of a dynamic analysis, so that to take into account geometric nonlinearities. So the confinement of a RC column is interpreted as a structural stability effect of concrete. And a significant role of the transverse reinforcement is revealed, that of preventing, by its close spacing and sufficient amount, the buckling of inner longitudinal concrete struts, which would lead to a global instability of the RC column. 4. The proposed truss model is statically indeterminate, so it exhibits some features, which are not met by the “strut-and-tie” model.展开更多
High spatial frequency laser induced periodic surface structures(HSFLs)on silicon substrates are often developed on flat surfaces at low fluences near ablation threshold of 0.1 J/cm2,seldom on microstructures or micro...High spatial frequency laser induced periodic surface structures(HSFLs)on silicon substrates are often developed on flat surfaces at low fluences near ablation threshold of 0.1 J/cm2,seldom on microstructures or microgrooves at relatively higher fluences above 1 J/cm^2.This work aims to enrich the variety of HSFLs-containing hierarchical microstructures,by femtosecond laser(pulse duration:457 fs,wavelength:1045 nm,and repetition rate:100 kHz)in liquids(water and acetone)at laser fluence of 1.7 J/cm^2.The period of Si-HSFLs in the range of 110–200 nm is independent of the scanning speeds(0.1,0.5,1 and 2 mm/s),line intervals(5,15 and 20μm)of scanning lines and scanning directions(perpendicular or parallel to light polarization direction).It is interestingly found that besides normal HSFLs whose orientations are perpendicular to the direction of light polarization,both clockwise or anticlockwise randomly tilted HSFLs with a maximal deviation angle of 50°as compared to those of normal HSFLSs are found on the microstructures with height gradients.Raman spectra and SEM characterization jointly clarify that surface melting and nanocapillary waves play important roles in the formation of Si-HSFLs.The fact that no HSFLs are produced by laser ablation in air indicates that moderate melting facilitated with ultrafast liquid cooling is beneficial for the formation of HSFLs by LALs.On the basis of our findings and previous reports,a synergistic formation mechanism for HSFLs at high fluence was proposed and discussed,including thermal melting with the concomitance of ultrafast cooling in liquids,transformation of the molten layers into ripples and nanotips by surface plasmon polaritons(SPP)and second-harmonic generation(SHG),and modulation of Si-HSFLs direction by both nanocapillary waves and the localized electric field coming from the excited large Si particles.展开更多
Protein Secondary Structure Prediction (PSSP) is considered as one of the major challenging tasks in bioinformatics, so many solutions have been proposed to solve that problem via trying to achieve more accurate predi...Protein Secondary Structure Prediction (PSSP) is considered as one of the major challenging tasks in bioinformatics, so many solutions have been proposed to solve that problem via trying to achieve more accurate prediction results. The goal of this paper is to develop and implement an intelligent based system to predict secondary structure of a protein from its primary amino acid sequence by using five models of Neural Network (NN). These models are Feed Forward Neural Network (FNN), Learning Vector Quantization (LVQ), Probabilistic Neural Network (PNN), Convolutional Neural Network (CNN), and CNN Fine Tuning for PSSP. To evaluate our approaches two datasets have been used. The first one contains 114 protein samples, and the second one contains 1845 protein samples.展开更多
Peculiar properties of morphological structures of organelle membranes were studied by fluorescent confocal microscopy. The list of objects in our experiments was represented by mitochondria, chloroplasts and vacuoles...Peculiar properties of morphological structures of organelle membranes were studied by fluorescent confocal microscopy. The list of objects in our experiments was represented by mitochondria, chloroplasts and vacuoles. During this study, identification of lipid microinclusions having the form of such lipid-protein structural microformations as lipid-protein microdomains, vesicles and membrane tubular structures (cytoplasmic transvacuolar strands and nanotubes) located in organelle membranes or bound up with them was conducted. Such membrane probes as laurdan, DPH, ANS and bis-ANS were used. Comparison of fluorescence intensity of these membrane probes was conducted. This investigation of the morphological properties of lipid-protein structural microformations was accompanied with analysis of 1) the phase state and 2) dynamics of microviscosity variations in the membrane elements of isolated plant cell organelles. Distributions of laurdan fluorescence generalized polarization (GP) values for the membrane on the whole and for the intensively fluorescing membrane segments were obtained. It was discovered that the microviscosity of intensively fluorescing membrane segments essentially differed from the microviscosity of the rest part of the membrane. In conclusion, some results of the study of peculiar properties of lipid-protein structural microformations related to the structure of organelle membranes and the discoveries made in this investigation are discussed.展开更多
Neural stem cells,which are capable of multi-potential differentiation and self-renewal,have recently been shown to have clinical potential for repairing central nervous system tissue damage.However,the theme trends a...Neural stem cells,which are capable of multi-potential differentiation and self-renewal,have recently been shown to have clinical potential for repairing central nervous system tissue damage.However,the theme trends and knowledge structures for human neural stem cells have not yet been studied bibliometrically.In this study,we retrieved 2742 articles from the PubMed database from 2013 to 2018 using "Neural Stem Cells" as the retrieval word.Co-word analysis was conducted to statistically quantify the characteristics and popular themes of human neural stem cell-related studies.Bibliographic data matrices were generated with the Bibliographic Item Co-Occurrence Matrix Builder.We identified 78 high-frequency Medical Subject Heading(MeSH)terms.A visual matrix was built with the repeated bisection method in gCLUTO software.A social network analysis network was generated with Ucinet 6.0 software and GraphPad Prism 5 software.The analyses demonstrated that in the 6-year period,hot topics were clustered into five categories.As suggested by the constructed strategic diagram,studies related to cytology and physiology were well-developed,whereas those related to neural stem cell applications,tissue engineering,metabolism and cell signaling,and neural stem cell pathology and virology remained immature.Neural stem cell therapy for stroke and Parkinson’s disease,the genetics of microRNAs and brain neoplasms,as well as neuroprotective agents,Zika virus,Notch receptor,neural crest and embryonic stem cells were identified as emerging hot spots.These undeveloped themes and popular topics are potential points of focus for new studies on human neural stem cells.展开更多
Heterogeneity of biological samples is usually considered a major obstacle for three-dimensional (3D) structure determination of macromolecular complexes. Heterogeneity may occur at the level of composition or conform...Heterogeneity of biological samples is usually considered a major obstacle for three-dimensional (3D) structure determination of macromolecular complexes. Heterogeneity may occur at the level of composition or conformational variability of complexes and affects most 3D structure determination methods that rely on signal averaging. Here, an approach is described that allows sorting structural states based on a 3D statistical approach, the 3D sampling and classification (3D-SC) of 3D structures derived from single particles imaged by cryo electron microscopy (cryo-EM). The method is based on jackknifing & bootstrapping of 3D sub-ensembles and 3D multivariate statistical analysis followed by 3D classification. The robustness of the statistical sorting procedure is corroborated using model data from an RNA polymerase structure and experimental data from a ribosome complex. It allows resolving multiple states within heterogeneous complexes that thus become amendable for a structural analysis despite of their highly flexible nature. The method has important implications for high-resolution structural studies and allows describing structure ensembles to provide insights into the dynamics of multi-component macromolecular assemblies.展开更多
We report results from ab-initio, self-consistent density functional theory (DFT) calculations of electronic, transport and bulk properties of rock salt magnesium sulfide (MgS). In the absence of experimental data on ...We report results from ab-initio, self-consistent density functional theory (DFT) calculations of electronic, transport and bulk properties of rock salt magnesium sulfide (MgS). In the absence of experimental data on these properties, except for the bulk modulus, these results are predictions. Our calculations utilized the Ceperley and Alder local density approximation (LDA) potential and the linear combination of Gaussian orbitals (LCGO). The key difference between our computations and other previous ab-initio DFT ones stems from our use of successively larger basis sets, in consecutive, self-consistent calculations, to attain the ground state of the material. We predicted an indirect (Γ-X) band gap of 3.278 eV for a room temperature lattice constant of 5.200Å. We obtained a predicted low temperature indirect (Γ-X) band gap of 3.512 eV, using the equilibrium lattice constant of 5.183Å. We found a theoretical value of 79.76 GPa for the bulk modulus;it agrees very well with the experimental finding of 78 ±3.7 GPa.展开更多
A novel, Ti-6 Al-4 V(Ti64)/Hydroxyapatite(HA at 5% by weight concentration) metal/ceramic composite has been fabricated using electron beam powder bed fusion(EPBF) additive manufacturing(AM): specifically, the commerc...A novel, Ti-6 Al-4 V(Ti64)/Hydroxyapatite(HA at 5% by weight concentration) metal/ceramic composite has been fabricated using electron beam powder bed fusion(EPBF) additive manufacturing(AM): specifically, the commercial electron beam melting(EBM?) process. In addition to solid Ti64 and Ti64/5% HA samples, four different unit cell(model) open-cellular mesh structures for the Ti64/5% HA composite were fabricated having densities ranging from 0.68 to 1.12 g/cm^3, and corresponding Young's moduli ranging from 2.9 to 8.0 GPa, and compressive strengths ranging from ~3 to 11 MPa. The solid Ti64/5%HA composite exhibited an optimal tensile strength of 123 MPa, and elongation of 5.5% in contrast to a maximum compressive strength of 875 MPa. Both the solid composite and mesh samples deformed primarily by brittle deformation, with the mesh samples exhibiting erratic, brittle crushing. Solid, EPBF-fabricated Ti64 samples had a Vickers microindentation hardness of 4.1 GPa while the Ti64/5%HA solid composite exhibited a Vickers microindentation hardness of 6.8 GPa. The lowest density Ti64/5%HA composite mesh strut sections had a Vickers microindentation hardness of 7.1 GPa. Optical metallography(OM) and scanning electron microscopy(SEM) analysis showed the HA dispersoids to be highly segregated along domain or grain boundaries, but homogeneously distributed along alpha(hcp) platelet boundaries within these domains in the Ti64 matrix for both the solid and mesh composites. The alpha platelet width varied from ~5 μm in the EPBF-fabricated Ti64 to ~1.1 m for the Ti64/5%HA mesh strut. The precursor HA powder diameter averaged 5 μm, in contrast to the dispersed HA particle diameters in the Ti64/5%HA composite which averaged 0.5 m. This work highlights the use of EPBF AM as a novel process for fabrication of a true composite structure, consisting of a Ti64 matrix and interspersed and exposed HA domains, which to the authors' knowledge has not been reported before. The results also illustrate the prospects not only for fabricating specialized, novel composite bone replacement scaffolds and implants, through the combination of Ti64 and HA, but also prospects for producing a variety of related metal/ceramic composites using EPBF AM.展开更多
On the basis of the analysis of field thermogeochemical data along abnormal zones of a thermal stream in the Bukhara-Khiva, oil-and-gas region of the Turan (Tegermen, Chagakul, Shimoly Alat, Beshtepa) was succeeded to...On the basis of the analysis of field thermogeochemical data along abnormal zones of a thermal stream in the Bukhara-Khiva, oil-and-gas region of the Turan (Tegermen, Chagakul, Shimoly Alat, Beshtepa) was succeeded to obtain important data on a deep structure of sites. Data of gas-chemical and geothermal observations show about confinedness of abnormal concentration of methane to zones of the increased values of the temperature field the measured values of temperatures (Tegermen Square and others). On geoelectric section mines 2-D of inversion of the MT-field depth of 4000 m are lower, among very high-resistance the chemogenic and carbonate deposits of the Paleozoic is traced the subvertical carrying-out abnormal zone. This zone is identified as the channel of a deep heat and mass transfer with which hydrocarbon (HC) deposits are connected. It is shown that electro-investigation when using a geophysical complex can and has to become “advancing” at exploration by oil and gas.展开更多
There were more expounding to north—west (west) trend fault and north\|east trend fault within Qiangtang Basin, North Part of Tibet, in the past literature. With increasing of geophysical exploration data, nearly eas...There were more expounding to north—west (west) trend fault and north\|east trend fault within Qiangtang Basin, North Part of Tibet, in the past literature. With increasing of geophysical exploration data, nearly east\|west trend structure began to be taken note to. Since the year of 1995, by a synthetic study to geophysical and geological data, that south\|north trend faulted structures are well developed. These structures should be paid much more attention to, because they have important theoretical meaning and practical significance.1 Spreading of south\|north faulted structure belt According to different geological and geophysical data, the six larger scale nearly south\|north faulted structure belt could be distinguished within the scope of east longitude 84°～96° and near Qiangtang Basin. The actual location of the six belts are nearly located in the west of the six meridian of east longitude 85°,87°,89°,91°,93°,95° or located near these meridian. The six south\|north faulted structure belts spread in the same interval with near 2° longitude interval. The more clear and much more significance of south\|north trend faulted structure belts are the two S—N trend faulted structure belts of east longitude 87° and 89°. There are S—N trend faulted structure belts in the west of east longitude 83°,81°, or near the longitudes. The structure belts spreading features,manifestation,geological function and its importance, and inter texture and structure are not exactly so same. The structure belts all different degree caused different region of geological structure or gravity field and magnetic field. There is different scale near S—N trend faulted structure belt between the belts.展开更多
In this study dynamic analysis of Soil Structure Interaction (SSI) effect on multi story reinforced concrete (RC) frame founded on soft soil (flexible base) is made and compared with fixed base. Two model 2D RC frames...In this study dynamic analysis of Soil Structure Interaction (SSI) effect on multi story reinforced concrete (RC) frame founded on soft soil (flexible base) is made and compared with fixed base. Two model 2D RC frames with 7 and 12 story are selected for analysis. Winkler Spring and half space direct method models are used for flexible base for the frames founded on two types of soft soils with shear velocity Vs < 150 m/s Asper Seismic Codes of Chinese GB50011-2010 Soil IV and Ethiopian ES8-2015 soil D. The frames are subjected to strong ground motion matched to response spectrums of soft soil of Chinese GB50011-2010 and Ethiopian ES8-2015 for linear time history analysis. The dynamic analysis result shows Spring and Fixed base mass participation 90% reaches in 2 or 3 modes but in direct method 11 to 30 modes for story 12 and 7 respectively. However, both flexible base models have bigger fundamental period of vibration and inter story drift but smaller base shear than fixed base. In addition, within the flexible base models the inter-story drift, second order effect (P-Δ) and Story shear distribution are different along the height of frames. The spring model shows larger Story drift and second order effect (P-Δ) at the bottom of Story for both soft soils types. On the other hand, half space direct method model indicates value reverse to spring model;it gives bigger Story drift and P-Δ effect in the top stories than fixed base. Finally, this study concludes that base shear reduction due to SSI may not be always beneficial. Because the gravity load is constant in both fixed and flexible bases that cause bigger P-Δ effect at the bottom stories due to increase, inter story drift and decrease story shear in flexible base.展开更多
The 1:200,000 middle-large scale Bouguer gravity anomaly data covering the southern segment of the Liaocheng-Lankao fault(SLLF)and its vicinity are analyzed with two methods.First,the Bouguer gravity anomaly data are ...The 1:200,000 middle-large scale Bouguer gravity anomaly data covering the southern segment of the Liaocheng-Lankao fault(SLLF)and its vicinity are analyzed with two methods.First,the Bouguer gravity anomaly data are decomposed by two-dimensional(2 D)wavelet to make the family of multi-scale modes correspond with density structure at different depths.Second,a two and half dimension(2.5 D)human-computer interaction inversion of the Bouguer gravity anomaly data are conducted with the constraints provided by two deep seismic sounding profiles(DSS1 and DSS2)crossing the study area to get the crustal density profiles.Based on the integrated study,we can draw the following conclusions:1)SLLF appears to be a deep fault with almost vertical dipping and rooted into the uppermost mantle;2)In the middle to upper crust SLLF shows an clear turning patterns and segmentation features;3)In the study area the epicentral distributions of the precisely re-located small earthquakes and the historical large earthquakes have a good correspondence with the turning patterns and segmentation features of SLLF;and 4)The results of the horizontal slices from 2 D wavelet decomposition show that there are significant differences in the density structure on the two sides of the fault.A well-defined concave structure with low density exists in the upper crust of the Dongming Depression on the west side of the fault,with the concave center being estimated at a depth of about 8 km.In contrast,the upper crust on the east side presents a relative thinner pattern in depth with a bit higher density.Meanwhile,the low-density structure in the middle crust underneath the fault is presumably caused by the uplift of the upper mantle materials and their intrusion along the deep rupture system.This paper clarified the inconsistency of fault system and epicenters of small earthquakes from upper to lower crust.The results indicated that the fault system plays an important governing role to the seismicity in this area.展开更多
Accuracy is a key factor in high-resolution remote sensing and photogrammetry. The factors that affect accuracy are imaging system errors and data processing errors. Due to the complexity of aerial camera errors, this...Accuracy is a key factor in high-resolution remote sensing and photogrammetry. The factors that affect accuracy are imaging system errors and data processing errors. Due to the complexity of aerial camera errors, this paper focuses on the design of digital aerial camera systems and the means to reduce system error and data processing inefficiencies. There are many kinds of digital aerial camera systems at present;however, these systems lack a unified physical model, which ultimately leads to more complicated designs and multi-camera modes. Such a system is complex and costly, as it is easily affected by factors such as vibration and temperature. Thus, the installed accuracy can only reach the millimeter level. Here, we describe a unified physical structure for a digital aerial camera that imitates an out-of-field multi-charge-coupled device (CCD), an in-field multi-CCD, and once-imaging and twice-imaging digital camera systems. This model is referred to as the variable baseline-height ratio spatiotemporal model. The variable ratio allows the opto-mechanical spatial parameters to be linked with height accuracy, thus providing a connection to the surface elevation. The twice-imaging digital camera prototype system and the wideband limb imaging spectrometer provide a transformation prototype from the current multi-rigid once-imaging aerial camera to a single rigid structure. Thus, our research lays a theoretical foundation and prototype references for the construction and industrialization of digital aerial systems.展开更多
The development of equations to predict tree height, crown diameter, crown depth from stem diameter of a tree species enables arborists, researchers, and urban forest managers to model costs and benefits, analyze alte...The development of equations to predict tree height, crown diameter, crown depth from stem diameter of a tree species enables arborists, researchers, and urban forest managers to model costs and benefits, analyze alternative management scenarios, and determine the best management practices for sustainable forests. The objective of this study was to develop regression prediction models for tree age, tree height, crown diameter, crown ratio and crown depth for A. senegal growing in Ferlo, in the northern Senegal. Four plantations of different years old (ISRA, 10 years old plantations, Ndodj, 8 years old plantations, Boulal, 5 years old plantations and Déali, 4 years old plantations) were selected. The following dendometric variables: crown height, crown diameter, stem diameter at the breast height, stem basal diameter (at 0.30 m) and the height from the tree base to first branch were measured on a total of 489 trees. The results suggested that the ecological structure of the different year old A. Senegal plantation revealed a bell-shaped form with left dissymmetric distribution indicating a predominance of individuals with small diameter at breast height. Allometry study of A. Senegal showed highly significant positive correlations (p = 0.00) between stem diameter at breast height, stem basal diameter, tree height, crown diameter and crown depth. Positive correlations were also found between crown diameter, tree height and crown height. Prediction models derived from these relationships can be used to estimate the tree height, stem diameter at breast height and crown depth from crown diameter with greater precision. As for A. Senegal age estimation, the established model is not strong as it can explain only 49.1% of the age variation.展开更多
Starting from well established results in pure mathematics, mainly transfinite set theory, E-infinity algebra over operads, fuzzy manifolds and fuzzy Lie symmetry groups, we construct an exact Weyl scaling for the hig...Starting from well established results in pure mathematics, mainly transfinite set theory, E-infinity algebra over operads, fuzzy manifolds and fuzzy Lie symmetry groups, we construct an exact Weyl scaling for the highly structured E-infinity rings corresponding to E-infinity theory of high energy physics. The final result is an exact expression for the energy density of the cosmos which agrees with previous analysis as well as accurate cosmological measurements and observations, such as COBE, WMAP and Planck. The paper is partially intended as a vivid demonstration of the power of pure mathematics in physics and cosmology.展开更多
The objective of the present paper is to develop nonlinear finite element method models for predicting the weld-induced initial deflection and residual stress of plating in steel stiffened-plate structures. For this p...The objective of the present paper is to develop nonlinear finite element method models for predicting the weld-induced initial deflection and residual stress of plating in steel stiffened-plate structures. For this purpose, three-dimensional thermo-elastic-plastic finite element method computations are performed with varying plate thickness and weld bead length (leg length) in welded plate panels, the latter being associated with weld heat input. The finite element models are verified by a comparison with experimental database which was obtained by the authors in separate studies with full scale measurements. It is concluded that the nonlinear finite element method models developed in the present paper are very accurate in terms of predicting the weld-induced initial imperfections of steel stiffened plate structures. Details of the numerical computations together with test database are documented.展开更多
In this paper,218 long period Rayleigh wave records from 7 seismic station of CDSN are selected.We applied a partitioned waveform inversion to these data in order to construct a 3\|D model of shear velocity down to 40...In this paper,218 long period Rayleigh wave records from 7 seismic station of CDSN are selected.We applied a partitioned waveform inversion to these data in order to construct a 3\|D model of shear velocity down to 400km depth in the crust and upper mantle of Qinghai\|Tibet plateau and Its Adjacent Regions (22°～44°N,70°～110°E).The first step of the waveform inversion used involved the matching of the waveforms of fundamental and highermost Ravleigh waves with waveforms synthesized from stratified models;in the second stage,the 3\|D model was constructed by solve linear constrains equation. The major structural features inferred from the surface waveform inversions can be summarized as follows:(1) There is a great contrast between surface waveform through Qinghai—Thibet plateau and the others.Main frequency of the former is lower than the latter, which indicate the crust depth of Qinghai—Tibet plateau is deeper than the others. In addition,the amplitude of about 30s period and 50s period is lower than both sides,which implied these exist lower velocity layer at about 25km depth and about 50km depth in Qinghai—Tibet plateau Crust.The former is common,the latter was argued because resolution of most method can not prove it.展开更多
For the solid blanket concept of helium cooled ceramic breeder (HCCB) demonstration fusion power plant (DEMO), a feasible blanket structure with configuration 2×X is proposed as considering relatively low tempera...For the solid blanket concept of helium cooled ceramic breeder (HCCB) demonstration fusion power plant (DEMO), a feasible blanket structure with configuration 2×X is proposed as considering relatively low temperature limit of neutron multiplier beryllium pebbles. Based on that, preliminary design for the typical blanket module of HCCB DEMO has been carried out and verified by thermal-hydraulic analysis and structural analysis. Furthermore, the specific relationship of maximum temperature depended on the surface heating of blanket key part first wall (FW) is also analyzed.展开更多
A numerical simulation is performed to find out a key vortical structure in the laminar-turbulent transition. A low-speed streak is generated inside a laminar boundary layer using an isolated cuboid roughness, aimed a...A numerical simulation is performed to find out a key vortical structure in the laminar-turbulent transition. A low-speed streak is generated inside a laminar boundary layer using an isolated cuboid roughness, aimed at providing an environment unstable to outer disturbances. Then, a short duration jet is issued into the boundary layer. When the jet velocity is low, some vortices appear in the boundary layer, but the transition of the boundary layer does not take place.However, when the jet velocity exceeds a certain threshold, two vortices newly appear above the elongated legs of a V-shaped vortex and only one of them is stretched and survives. After that,vortices are generated one after another around the survived one. By comparing the decayed and the survived vortices, it is found that the difference in their heights is the key characteristic which leads to the transition.展开更多
文摘Achievements are presented for truss models of RC structures developed in previous years: 1. Two constitutive models, biaxial and triaxial, are based on regular trusses, with bars obeying nonlinear uniaxial σ-ε laws of material under simulation;both models have been compared with test results and show a dependence of Poisson ratio on curvature of σ-ε law. 2. A truss finite element has been used in the nonlinear static and dynamic analysis of plane RC frames;it has been compared with test results and describes, in a simple way, the formation of plastic hinges. 3. Thanks to the very simple geometry of a truss, the equilibrium equations can be easily written and the stiffness matrix can be easily updated, both with respect to the deformed truss, within each step of a static incremental loading or within each time step of a dynamic analysis, so that to take into account geometric nonlinearities. So the confinement of a RC column is interpreted as a structural stability effect of concrete. And a significant role of the transverse reinforcement is revealed, that of preventing, by its close spacing and sufficient amount, the buckling of inner longitudinal concrete struts, which would lead to a global instability of the RC column. 4. The proposed truss model is statically indeterminate, so it exhibits some features, which are not met by the “strut-and-tie” model.
文摘High spatial frequency laser induced periodic surface structures(HSFLs)on silicon substrates are often developed on flat surfaces at low fluences near ablation threshold of 0.1 J/cm2,seldom on microstructures or microgrooves at relatively higher fluences above 1 J/cm^2.This work aims to enrich the variety of HSFLs-containing hierarchical microstructures,by femtosecond laser(pulse duration:457 fs,wavelength:1045 nm,and repetition rate:100 kHz)in liquids(water and acetone)at laser fluence of 1.7 J/cm^2.The period of Si-HSFLs in the range of 110–200 nm is independent of the scanning speeds(0.1,0.5,1 and 2 mm/s),line intervals(5,15 and 20μm)of scanning lines and scanning directions(perpendicular or parallel to light polarization direction).It is interestingly found that besides normal HSFLs whose orientations are perpendicular to the direction of light polarization,both clockwise or anticlockwise randomly tilted HSFLs with a maximal deviation angle of 50°as compared to those of normal HSFLSs are found on the microstructures with height gradients.Raman spectra and SEM characterization jointly clarify that surface melting and nanocapillary waves play important roles in the formation of Si-HSFLs.The fact that no HSFLs are produced by laser ablation in air indicates that moderate melting facilitated with ultrafast liquid cooling is beneficial for the formation of HSFLs by LALs.On the basis of our findings and previous reports,a synergistic formation mechanism for HSFLs at high fluence was proposed and discussed,including thermal melting with the concomitance of ultrafast cooling in liquids,transformation of the molten layers into ripples and nanotips by surface plasmon polaritons(SPP)and second-harmonic generation(SHG),and modulation of Si-HSFLs direction by both nanocapillary waves and the localized electric field coming from the excited large Si particles.
文摘Protein Secondary Structure Prediction (PSSP) is considered as one of the major challenging tasks in bioinformatics, so many solutions have been proposed to solve that problem via trying to achieve more accurate prediction results. The goal of this paper is to develop and implement an intelligent based system to predict secondary structure of a protein from its primary amino acid sequence by using five models of Neural Network (NN). These models are Feed Forward Neural Network (FNN), Learning Vector Quantization (LVQ), Probabilistic Neural Network (PNN), Convolutional Neural Network (CNN), and CNN Fine Tuning for PSSP. To evaluate our approaches two datasets have been used. The first one contains 114 protein samples, and the second one contains 1845 protein samples.
文摘Peculiar properties of morphological structures of organelle membranes were studied by fluorescent confocal microscopy. The list of objects in our experiments was represented by mitochondria, chloroplasts and vacuoles. During this study, identification of lipid microinclusions having the form of such lipid-protein structural microformations as lipid-protein microdomains, vesicles and membrane tubular structures (cytoplasmic transvacuolar strands and nanotubes) located in organelle membranes or bound up with them was conducted. Such membrane probes as laurdan, DPH, ANS and bis-ANS were used. Comparison of fluorescence intensity of these membrane probes was conducted. This investigation of the morphological properties of lipid-protein structural microformations was accompanied with analysis of 1) the phase state and 2) dynamics of microviscosity variations in the membrane elements of isolated plant cell organelles. Distributions of laurdan fluorescence generalized polarization (GP) values for the membrane on the whole and for the intensively fluorescing membrane segments were obtained. It was discovered that the microviscosity of intensively fluorescing membrane segments essentially differed from the microviscosity of the rest part of the membrane. In conclusion, some results of the study of peculiar properties of lipid-protein structural microformations related to the structure of organelle membranes and the discoveries made in this investigation are discussed.
基金supported by the National Natural Science Foundation of China,No.81471308(to JL)the Stem Cell Clinical Research Project in China,No.CMR-20161129-1003(to JL)the Innovation Technology Funding of Dalian in China,No.2018J11CY025(to JL)
文摘Neural stem cells,which are capable of multi-potential differentiation and self-renewal,have recently been shown to have clinical potential for repairing central nervous system tissue damage.However,the theme trends and knowledge structures for human neural stem cells have not yet been studied bibliometrically.In this study,we retrieved 2742 articles from the PubMed database from 2013 to 2018 using "Neural Stem Cells" as the retrieval word.Co-word analysis was conducted to statistically quantify the characteristics and popular themes of human neural stem cell-related studies.Bibliographic data matrices were generated with the Bibliographic Item Co-Occurrence Matrix Builder.We identified 78 high-frequency Medical Subject Heading(MeSH)terms.A visual matrix was built with the repeated bisection method in gCLUTO software.A social network analysis network was generated with Ucinet 6.0 software and GraphPad Prism 5 software.The analyses demonstrated that in the 6-year period,hot topics were clustered into five categories.As suggested by the constructed strategic diagram,studies related to cytology and physiology were well-developed,whereas those related to neural stem cell applications,tissue engineering,metabolism and cell signaling,and neural stem cell pathology and virology remained immature.Neural stem cell therapy for stroke and Parkinson’s disease,the genetics of microRNAs and brain neoplasms,as well as neuroprotective agents,Zika virus,Notch receptor,neural crest and embryonic stem cells were identified as emerging hot spots.These undeveloped themes and popular topics are potential points of focus for new studies on human neural stem cells.
文摘Heterogeneity of biological samples is usually considered a major obstacle for three-dimensional (3D) structure determination of macromolecular complexes. Heterogeneity may occur at the level of composition or conformational variability of complexes and affects most 3D structure determination methods that rely on signal averaging. Here, an approach is described that allows sorting structural states based on a 3D statistical approach, the 3D sampling and classification (3D-SC) of 3D structures derived from single particles imaged by cryo electron microscopy (cryo-EM). The method is based on jackknifing & bootstrapping of 3D sub-ensembles and 3D multivariate statistical analysis followed by 3D classification. The robustness of the statistical sorting procedure is corroborated using model data from an RNA polymerase structure and experimental data from a ribosome complex. It allows resolving multiple states within heterogeneous complexes that thus become amendable for a structural analysis despite of their highly flexible nature. The method has important implications for high-resolution structural studies and allows describing structure ensembles to provide insights into the dynamics of multi-component macromolecular assemblies.
文摘We report results from ab-initio, self-consistent density functional theory (DFT) calculations of electronic, transport and bulk properties of rock salt magnesium sulfide (MgS). In the absence of experimental data on these properties, except for the bulk modulus, these results are predictions. Our calculations utilized the Ceperley and Alder local density approximation (LDA) potential and the linear combination of Gaussian orbitals (LCGO). The key difference between our computations and other previous ab-initio DFT ones stems from our use of successively larger basis sets, in consecutive, self-consistent calculations, to attain the ground state of the material. We predicted an indirect (Γ-X) band gap of 3.278 eV for a room temperature lattice constant of 5.200Å. We obtained a predicted low temperature indirect (Γ-X) band gap of 3.512 eV, using the equilibrium lattice constant of 5.183Å. We found a theoretical value of 79.76 GPa for the bulk modulus;it agrees very well with the experimental finding of 78 ±3.7 GPa.
文摘A novel, Ti-6 Al-4 V(Ti64)/Hydroxyapatite(HA at 5% by weight concentration) metal/ceramic composite has been fabricated using electron beam powder bed fusion(EPBF) additive manufacturing(AM): specifically, the commercial electron beam melting(EBM?) process. In addition to solid Ti64 and Ti64/5% HA samples, four different unit cell(model) open-cellular mesh structures for the Ti64/5% HA composite were fabricated having densities ranging from 0.68 to 1.12 g/cm^3, and corresponding Young's moduli ranging from 2.9 to 8.0 GPa, and compressive strengths ranging from ~3 to 11 MPa. The solid Ti64/5%HA composite exhibited an optimal tensile strength of 123 MPa, and elongation of 5.5% in contrast to a maximum compressive strength of 875 MPa. Both the solid composite and mesh samples deformed primarily by brittle deformation, with the mesh samples exhibiting erratic, brittle crushing. Solid, EPBF-fabricated Ti64 samples had a Vickers microindentation hardness of 4.1 GPa while the Ti64/5%HA solid composite exhibited a Vickers microindentation hardness of 6.8 GPa. The lowest density Ti64/5%HA composite mesh strut sections had a Vickers microindentation hardness of 7.1 GPa. Optical metallography(OM) and scanning electron microscopy(SEM) analysis showed the HA dispersoids to be highly segregated along domain or grain boundaries, but homogeneously distributed along alpha(hcp) platelet boundaries within these domains in the Ti64 matrix for both the solid and mesh composites. The alpha platelet width varied from ~5 μm in the EPBF-fabricated Ti64 to ~1.1 m for the Ti64/5%HA mesh strut. The precursor HA powder diameter averaged 5 μm, in contrast to the dispersed HA particle diameters in the Ti64/5%HA composite which averaged 0.5 m. This work highlights the use of EPBF AM as a novel process for fabrication of a true composite structure, consisting of a Ti64 matrix and interspersed and exposed HA domains, which to the authors' knowledge has not been reported before. The results also illustrate the prospects not only for fabricating specialized, novel composite bone replacement scaffolds and implants, through the combination of Ti64 and HA, but also prospects for producing a variety of related metal/ceramic composites using EPBF AM.
文摘On the basis of the analysis of field thermogeochemical data along abnormal zones of a thermal stream in the Bukhara-Khiva, oil-and-gas region of the Turan (Tegermen, Chagakul, Shimoly Alat, Beshtepa) was succeeded to obtain important data on a deep structure of sites. Data of gas-chemical and geothermal observations show about confinedness of abnormal concentration of methane to zones of the increased values of the temperature field the measured values of temperatures (Tegermen Square and others). On geoelectric section mines 2-D of inversion of the MT-field depth of 4000 m are lower, among very high-resistance the chemogenic and carbonate deposits of the Paleozoic is traced the subvertical carrying-out abnormal zone. This zone is identified as the channel of a deep heat and mass transfer with which hydrocarbon (HC) deposits are connected. It is shown that electro-investigation when using a geophysical complex can and has to become “advancing” at exploration by oil and gas.
文摘There were more expounding to north—west (west) trend fault and north\|east trend fault within Qiangtang Basin, North Part of Tibet, in the past literature. With increasing of geophysical exploration data, nearly east\|west trend structure began to be taken note to. Since the year of 1995, by a synthetic study to geophysical and geological data, that south\|north trend faulted structures are well developed. These structures should be paid much more attention to, because they have important theoretical meaning and practical significance.1 Spreading of south\|north faulted structure belt According to different geological and geophysical data, the six larger scale nearly south\|north faulted structure belt could be distinguished within the scope of east longitude 84°～96° and near Qiangtang Basin. The actual location of the six belts are nearly located in the west of the six meridian of east longitude 85°,87°,89°,91°,93°,95° or located near these meridian. The six south\|north faulted structure belts spread in the same interval with near 2° longitude interval. The more clear and much more significance of south\|north trend faulted structure belts are the two S—N trend faulted structure belts of east longitude 87° and 89°. There are S—N trend faulted structure belts in the west of east longitude 83°,81°, or near the longitudes. The structure belts spreading features,manifestation,geological function and its importance, and inter texture and structure are not exactly so same. The structure belts all different degree caused different region of geological structure or gravity field and magnetic field. There is different scale near S—N trend faulted structure belt between the belts.
文摘In this study dynamic analysis of Soil Structure Interaction (SSI) effect on multi story reinforced concrete (RC) frame founded on soft soil (flexible base) is made and compared with fixed base. Two model 2D RC frames with 7 and 12 story are selected for analysis. Winkler Spring and half space direct method models are used for flexible base for the frames founded on two types of soft soils with shear velocity Vs < 150 m/s Asper Seismic Codes of Chinese GB50011-2010 Soil IV and Ethiopian ES8-2015 soil D. The frames are subjected to strong ground motion matched to response spectrums of soft soil of Chinese GB50011-2010 and Ethiopian ES8-2015 for linear time history analysis. The dynamic analysis result shows Spring and Fixed base mass participation 90% reaches in 2 or 3 modes but in direct method 11 to 30 modes for story 12 and 7 respectively. However, both flexible base models have bigger fundamental period of vibration and inter story drift but smaller base shear than fixed base. In addition, within the flexible base models the inter-story drift, second order effect (P-Δ) and Story shear distribution are different along the height of frames. The spring model shows larger Story drift and second order effect (P-Δ) at the bottom of Story for both soft soils types. On the other hand, half space direct method model indicates value reverse to spring model;it gives bigger Story drift and P-Δ effect in the top stories than fixed base. Finally, this study concludes that base shear reduction due to SSI may not be always beneficial. Because the gravity load is constant in both fixed and flexible bases that cause bigger P-Δ effect at the bottom stories due to increase, inter story drift and decrease story shear in flexible base.
基金financial support from China Scholarship Councilthe support from the Seismic Youth Founding of GEC (Grant No. YFGEC2016008)the National Natural Science Foundation of China(Grant No. 41474077)
文摘The 1:200,000 middle-large scale Bouguer gravity anomaly data covering the southern segment of the Liaocheng-Lankao fault(SLLF)and its vicinity are analyzed with two methods.First,the Bouguer gravity anomaly data are decomposed by two-dimensional(2 D)wavelet to make the family of multi-scale modes correspond with density structure at different depths.Second,a two and half dimension(2.5 D)human-computer interaction inversion of the Bouguer gravity anomaly data are conducted with the constraints provided by two deep seismic sounding profiles(DSS1 and DSS2)crossing the study area to get the crustal density profiles.Based on the integrated study,we can draw the following conclusions:1)SLLF appears to be a deep fault with almost vertical dipping and rooted into the uppermost mantle;2)In the middle to upper crust SLLF shows an clear turning patterns and segmentation features;3)In the study area the epicentral distributions of the precisely re-located small earthquakes and the historical large earthquakes have a good correspondence with the turning patterns and segmentation features of SLLF;and 4)The results of the horizontal slices from 2 D wavelet decomposition show that there are significant differences in the density structure on the two sides of the fault.A well-defined concave structure with low density exists in the upper crust of the Dongming Depression on the west side of the fault,with the concave center being estimated at a depth of about 8 km.In contrast,the upper crust on the east side presents a relative thinner pattern in depth with a bit higher density.Meanwhile,the low-density structure in the middle crust underneath the fault is presumably caused by the uplift of the upper mantle materials and their intrusion along the deep rupture system.This paper clarified the inconsistency of fault system and epicenters of small earthquakes from upper to lower crust.The results indicated that the fault system plays an important governing role to the seismicity in this area.
基金The National Major Plan Research and Development Project(2017YFB0503003)The National Natural Science Foundation of China(11174017)+1 种基金The National 863 Subject(2007AA12Z111,2006AA12Z119)The Special Research Fund for Doctoral Programs in Colleges and Universities(20130001110046).
文摘Accuracy is a key factor in high-resolution remote sensing and photogrammetry. The factors that affect accuracy are imaging system errors and data processing errors. Due to the complexity of aerial camera errors, this paper focuses on the design of digital aerial camera systems and the means to reduce system error and data processing inefficiencies. There are many kinds of digital aerial camera systems at present;however, these systems lack a unified physical model, which ultimately leads to more complicated designs and multi-camera modes. Such a system is complex and costly, as it is easily affected by factors such as vibration and temperature. Thus, the installed accuracy can only reach the millimeter level. Here, we describe a unified physical structure for a digital aerial camera that imitates an out-of-field multi-charge-coupled device (CCD), an in-field multi-CCD, and once-imaging and twice-imaging digital camera systems. This model is referred to as the variable baseline-height ratio spatiotemporal model. The variable ratio allows the opto-mechanical spatial parameters to be linked with height accuracy, thus providing a connection to the surface elevation. The twice-imaging digital camera prototype system and the wideband limb imaging spectrometer provide a transformation prototype from the current multi-rigid once-imaging aerial camera to a single rigid structure. Thus, our research lays a theoretical foundation and prototype references for the construction and industrialization of digital aerial systems.
文摘The development of equations to predict tree height, crown diameter, crown depth from stem diameter of a tree species enables arborists, researchers, and urban forest managers to model costs and benefits, analyze alternative management scenarios, and determine the best management practices for sustainable forests. The objective of this study was to develop regression prediction models for tree age, tree height, crown diameter, crown ratio and crown depth for A. senegal growing in Ferlo, in the northern Senegal. Four plantations of different years old (ISRA, 10 years old plantations, Ndodj, 8 years old plantations, Boulal, 5 years old plantations and Déali, 4 years old plantations) were selected. The following dendometric variables: crown height, crown diameter, stem diameter at the breast height, stem basal diameter (at 0.30 m) and the height from the tree base to first branch were measured on a total of 489 trees. The results suggested that the ecological structure of the different year old A. Senegal plantation revealed a bell-shaped form with left dissymmetric distribution indicating a predominance of individuals with small diameter at breast height. Allometry study of A. Senegal showed highly significant positive correlations (p = 0.00) between stem diameter at breast height, stem basal diameter, tree height, crown diameter and crown depth. Positive correlations were also found between crown diameter, tree height and crown height. Prediction models derived from these relationships can be used to estimate the tree height, stem diameter at breast height and crown depth from crown diameter with greater precision. As for A. Senegal age estimation, the established model is not strong as it can explain only 49.1% of the age variation.
文摘Starting from well established results in pure mathematics, mainly transfinite set theory, E-infinity algebra over operads, fuzzy manifolds and fuzzy Lie symmetry groups, we construct an exact Weyl scaling for the highly structured E-infinity rings corresponding to E-infinity theory of high energy physics. The final result is an exact expression for the energy density of the cosmos which agrees with previous analysis as well as accurate cosmological measurements and observations, such as COBE, WMAP and Planck. The paper is partially intended as a vivid demonstration of the power of pure mathematics in physics and cosmology.
文摘The objective of the present paper is to develop nonlinear finite element method models for predicting the weld-induced initial deflection and residual stress of plating in steel stiffened-plate structures. For this purpose, three-dimensional thermo-elastic-plastic finite element method computations are performed with varying plate thickness and weld bead length (leg length) in welded plate panels, the latter being associated with weld heat input. The finite element models are verified by a comparison with experimental database which was obtained by the authors in separate studies with full scale measurements. It is concluded that the nonlinear finite element method models developed in the present paper are very accurate in terms of predicting the weld-induced initial imperfections of steel stiffened plate structures. Details of the numerical computations together with test database are documented.
文摘In this paper,218 long period Rayleigh wave records from 7 seismic station of CDSN are selected.We applied a partitioned waveform inversion to these data in order to construct a 3\|D model of shear velocity down to 400km depth in the crust and upper mantle of Qinghai\|Tibet plateau and Its Adjacent Regions (22°～44°N,70°～110°E).The first step of the waveform inversion used involved the matching of the waveforms of fundamental and highermost Ravleigh waves with waveforms synthesized from stratified models;in the second stage,the 3\|D model was constructed by solve linear constrains equation. The major structural features inferred from the surface waveform inversions can be summarized as follows:(1) There is a great contrast between surface waveform through Qinghai—Thibet plateau and the others.Main frequency of the former is lower than the latter, which indicate the crust depth of Qinghai—Tibet plateau is deeper than the others. In addition,the amplitude of about 30s period and 50s period is lower than both sides,which implied these exist lower velocity layer at about 25km depth and about 50km depth in Qinghai—Tibet plateau Crust.The former is common,the latter was argued because resolution of most method can not prove it.
基金supported by the National Special Project of China for magnetic confined nuclear fusion energy(2015GB108004)
文摘For the solid blanket concept of helium cooled ceramic breeder (HCCB) demonstration fusion power plant (DEMO), a feasible blanket structure with configuration 2×X is proposed as considering relatively low temperature limit of neutron multiplier beryllium pebbles. Based on that, preliminary design for the typical blanket module of HCCB DEMO has been carried out and verified by thermal-hydraulic analysis and structural analysis. Furthermore, the specific relationship of maximum temperature depended on the surface heating of blanket key part first wall (FW) is also analyzed.
文摘A numerical simulation is performed to find out a key vortical structure in the laminar-turbulent transition. A low-speed streak is generated inside a laminar boundary layer using an isolated cuboid roughness, aimed at providing an environment unstable to outer disturbances. Then, a short duration jet is issued into the boundary layer. When the jet velocity is low, some vortices appear in the boundary layer, but the transition of the boundary layer does not take place.However, when the jet velocity exceeds a certain threshold, two vortices newly appear above the elongated legs of a V-shaped vortex and only one of them is stretched and survives. After that,vortices are generated one after another around the survived one. By comparing the decayed and the survived vortices, it is found that the difference in their heights is the key characteristic which leads to the transition.
