Coronary artery calcium data and reporting system(CAC-DRS)is a recently introduced standardized reporting system for calcium scoring on computed tomography.CAC-DRS provides four risk categories(0,1,2 and 3)along with ...Coronary artery calcium data and reporting system(CAC-DRS)is a recently introduced standardized reporting system for calcium scoring on computed tomography.CAC-DRS provides four risk categories(0,1,2 and 3)along with treatment recommendations for each category.As with any other new reporting platform,CAC-DRS has both advantages and disadvantages.Improved communication,better clarity of details,organized management recommendations and utility in future research and education are the major strengths of CAC-DRS.It has many limitations such as questionable need for a new system,few missing components,use of a less accurate visual method and treatment suggestions based on expert opinion instead of clinical trials.In this contemporary review,we discuss the new reporting system CAC-DRS,its application,strengths and limitations and conclude with some remarks for the future.展开更多
The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of ...The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of mining situations. While common wisdom sensibly limits the use of the resultant pillar strength equations and methods to design scenarios that are consistent with the founding database, there are a number of examples where failures have occurred as a direct result of applying empirical design methods to coal pillar design problems that are inconsistent with the founding database. This paper explores the reasons why empirically derived coal pillar strength equations tend to be problem-specific and should be considered as providing no more than a pillar strength ‘‘index." These include the non-consideration of overburden horizontal stress within the mine stability problem, an inadequate definition of supercritical overburden behavior as it applies to standing coal pillars, and the non-consideration of overburden displacement and coal pillar strain limits. All of which combine to potentially complicate and confuse the back-analysis of coal pillar strength from failed cases. A modified coal pillar design representation and model are presented based on coal pillars acting to reinforce a horizontally stressed overburden, rather than suspend an otherwise unstable self-loaded overburden or section, the latter having been at the core of historical empirical studies into coal pillar strength and stability.展开更多
Overhanging rock slopes(steeper than 90°) are typically avoided in rock engineering design, particularly where the scale of the slope exceeds the scale of fracturing present in the rock mass. This paper highlight...Overhanging rock slopes(steeper than 90°) are typically avoided in rock engineering design, particularly where the scale of the slope exceeds the scale of fracturing present in the rock mass. This paper highlights an integrated approach of designing overhanging rock slopes where the relative dimensions of the slope exceed the scale of fracturing and the rock mass failure needs to be considered rather than kinematic release of individual blocks. The key to the method is a simplified limit equilibrium(LE) tool that was used for the support design and analysis of a multi-faceted overhanging rock slope. The overhanging slopes required complex geometries with constantly changing orientations. The overhanging rock varied in height from 30 m to 66 m. Geomechanical modelling combined with discrete fracture network(DFN)representation of the rock mass was used to validate the rock mass strength assumptions and the failure mechanism assumed in the LE model. The advantage of the simplified LE method is that buttress and support design iterations(along with sensitivity analysis of design parameters) can be completed for various cross-sections along the proposed overhanging rock sections in an efficient manner, compared to the more time-intensive, sophisticated methods that were used for the initial validation. The method described presents the development of this design tool and assumptions made for a specific overhanging rock slope design. Other locations will have different geological conditions that can control the potential behaviour of rock slopes, however, the approach presented can be applied as a general guiding design principle for overhanging rock cut slope.展开更多
The surface yield strength(σ_(ms))for various carbon steels was studied by means of X-ray diffraction method.The results showed that it is.far below the bulk yield strength,and is the resistance against plastic defor...The surface yield strength(σ_(ms))for various carbon steels was studied by means of X-ray diffraction method.The results showed that it is.far below the bulk yield strength,and is the resistance against plastic deformation in the surface layer.The smooth fatigue limit is associ- ated with crack initiation which is a result of accumulation of plastic deformation.Experimen- tal results showed the relation of smooth fatigue limit for 50% survival with σ_(ms)is σ_(ms)=0.81 tO 1.02 σ_(-1)for different steels.The smooth fatigue limit of a medium carbon steel for 99.9% survival with σ_(ms)is σ_(ms)=0.98 tO 1.10 σ_(-1).It is less expensive and time consuming to measure σ_(ms)than σ_(-1).展开更多
With applied dislocation theory,the effects of shear and normal stresses on the slide and climb motions at the same section of a crystal were analyzed.And,based on the synergetic effect of both normal and shear strain...With applied dislocation theory,the effects of shear and normal stresses on the slide and climb motions at the same section of a crystal were analyzed.And,based on the synergetic effect of both normal and shear strain specific energies,the concept of the total equivalent strain specific energy(TESSE)at an oblique section and a new strength theory named as limiting strain energy strength theory(LSEST)were proposed.As for isotropic materials,the plastic yielding or brittle fracture of under uniaxial stress state would occur when the maximum TESSE reached the strain specific energy,also the expressions on the equivalent stresses and a function of failure of the LSEST under different principal stress states were obtained.Relationship formulas among the tensile, compressive and shear yield strengths for plastic metals were derived.These theoretical predictions,according to the LSEST,were consistent very well with experiment results of tensile,compressive and torsion tests of three plastic metals and other experiment results from open literatures.This novel LSEST might also help for strength calculation of other materials.展开更多
Resistance multi-spot welding （MSW） in column, triangle and tetragonal symmetry arrangements was prepared using cold-rolled 301L high-strength sheets, and their static and fatigue properties were in- vestigated. The...Resistance multi-spot welding （MSW） in column, triangle and tetragonal symmetry arrangements was prepared using cold-rolled 301L high-strength sheets, and their static and fatigue properties were in- vestigated. The effects of spot welds on the fracture strengths and fatigue limits were discussed. The results show that the static strengths can be estimated using an inherent linear relationship formula of the load versus the welding area. It was based on the 28%-33% volume fraction of α′ martensite induced at the interfacial spot weld fracture because of the failure deformation. The fatigue limits of the MSW nonlin- early increase with the number of spot welds. The arrangement of spot welds in the MSW significantly affects the average fatigue limit of each spot weld; its 26% maximum reduction occurred in the triangle, and the interaction stress between spot welds led to its 18% reduction in the tetragonal symmetry. The calculated fatigue stress of all MSW loadings with their mean fatigue limits was 230-270 MPa.展开更多
The finite element limit analysis method has the advantages of both numerical and traditional limit equilibrium techniques and it is particularly useful to geotechnical engineering.This method has been developed in Ch...The finite element limit analysis method has the advantages of both numerical and traditional limit equilibrium techniques and it is particularly useful to geotechnical engineering.This method has been developed in China,following well-accepted international procedures,to enhance understanding of stability issues in a number of geotechnical settings.Great advancements have been made in basic theory,the improvement of computational precision,and the broadening of practical applications.This paper presents the results of research on（1） the efficient design of embedded anti-slide piles,（2） the stability analysis of reservoir slopes with strength reduction theory,and（3） the determination of the ultimate bearing capacity of foundations using step-loading FEM（overloading）.These three applications are evidence of the design improvements and benefits made possible in geotechnical engineering by finite element modeling.展开更多
Extensive data of undrained shear strength for various remolded soils are compiled to normalize the remolded undrained strength. Remolded soils have a wide spectrum of liquid limits ranging from 25% to 412%. It is fou...Extensive data of undrained shear strength for various remolded soils are compiled to normalize the remolded undrained strength. Remolded soils have a wide spectrum of liquid limits ranging from 25% to 412%. It is found that the remolded undrained strength is a function of water content and liquid limit. Furthermore, a simple index designated as normalized water content w * is introduced for normalizing remolded undrained strength for various soils. The normalized water content w * is the ratio of water content to liquid limit. The relationship between the remolded undrained strength and the normalized water content can be expressed by a simple equation. The new simple equation is not only valuable theoretically for helping in assessing the in situ mechanical behavior, but also useful to ocean engineering practice.展开更多
This paper presents the results of four partially prestressed ultra-high strength concrete beams in flexure. The test results are used to evaluate the effects of prestressing tendon depth and area on flexure behavior ...This paper presents the results of four partially prestressed ultra-high strength concrete beams in flexure. The test results are used to evaluate the effects of prestressing tendon depth and area on flexure behavior of specimen beams. The test results indicate that: the cracking load,yielding load,peak load and stiffness postcracking of specimen beams are enhanced by reducing prestressing tendon depth or increasing prestressing tendon area, and the flexural ductility is improved by increasing prestressing tendon depth or reducing prestressing tendon area. The effect of complex reinforcement index considering the strength of the equivalence principle and the reinforcement position on loading levels under serviceability limit state,flexural strength and displacement ductility factor are studied. The influence coefficient of prestressing tendon kpis introduced in the complex reinforcement index. As the complex reinforcement index increases, the loading levels under serviceability limit state and flexural strength increases linearly,and the displacement ductility factor decreases linearly. The test results also verify the conventional beam flexural theory based on the plane cross-section assumption for predicting ultimate flexural strength of partially prestressed ultra-high strength concrete beams is valid. After the introduction of the coefficient kp,the calculation method of cracks in code for design of concrete structure in china are appropriated for the specimen beams.展开更多
Structural analysis of steel frames is typically performed using beam elements. Since these elements are unable to explicitly capture the local buckling behavior of steel cross-sections, traditional steel design speci...Structural analysis of steel frames is typically performed using beam elements. Since these elements are unable to explicitly capture the local buckling behavior of steel cross-sections, traditional steel design specifications use the concept of cross-section classification to determine the extent to which the strength and deformation capacity of a cross-section are affected by local buckling. The use of plastic design methods are restricted to Class 1 cross-sections, which possess sufficient rotation capacity for plastic hinges to develop and a collapse mechanism to form. Local buckling prevents the development of plastic hinges with such rotation capacity for cross-sections of higher classes and, unless computationally demanding shell elements are used, elastic analysis is required. However, this article demonstrates that local buckling can be mimicked effectively in beam elements by incorporating the continuous strength method (CSM) strain limits into the analysis. Furthermore, by performing an advanced analysis that accounts for both geometric and material nonlinearities, no additional design checks are required. The positive influence of the strain hardening observed in stocky cross-sections can also be harnessed, provided a suitably accurate stress–strain relationship is adopted;a quad-linear material model for hot-rolled steels is described for this purpose. The CSM strain limits allow cross-sections of all slenderness to be analyzed in a consistent advanced analysis framework and to benefit from the appropriate level of load redistribution. The proposed approach is applied herein to individual members, continuous beams, and frames, and is shown to bring significant benefits in terms of accuracy and consistency over current steel design specifications.展开更多
Stress-strength model is a basic and important tool for reliability analysis.There are few methods to assess the confidence limit of interference reliability when the distribution parameters of stress and strength are...Stress-strength model is a basic and important tool for reliability analysis.There are few methods to assess the confidence limit of interference reliability when the distribution parameters of stress and strength are all unknown.A new assessment method of interference reliability is proposed and the estimates of the distribution parameters are accordingly given.The lower confidence limit of interference reliability with given confidence can be obtained with the method even though the parameters are all unknown.Simulation studies and an engineering application are conducted to validate the method,which suggest that the method provides precise estimates even for sample size of approximately.展开更多
The present paper aims at giving some general ideas concerning the micromechanical approach of the strength of a porous material. It is shown that its determination theoretically amounts to solving a nonlinear boundar...The present paper aims at giving some general ideas concerning the micromechanical approach of the strength of a porous material. It is shown that its determination theoretically amounts to solving a nonlinear boundary value problem defined on a representative elementary volume(REV). The principle of nonlinear homogenization is illustrated based on the case of a solid phase having a Green’s strength criterion. An original refinement of the so-called secant method(based on two reference strains) is also provided. The paper also describes the main feature of the Gurson’s model which implements the principle of limit analysis on a conceptual model of hollow sphere. The last part of the paper gives some ideas concerning poromechanical couplings.展开更多
A simplified procedure was described to estimate the FEL of three kinds of hot-mix asphalt concrete （HMAC） without doing any fatigue tests. The procedure required two fundamental properties of HMAC, tensile strength...A simplified procedure was described to estimate the FEL of three kinds of hot-mix asphalt concrete （HMAC） without doing any fatigue tests. The procedure required two fundamental properties of HMAC, tensile strength under different temperatures and strain rates, and flexural stiffness under different stain levels. This information can reliably be obtained in simple tests, which are the monotonic uniaxial tensile test （MUTT） and the four-point bending test （FPBT）. A new parameter, the initial stress ratio Rinitial, was introduced to connect these two tests, which was defined as the ratio of applied initial stress and tensile strength of the specimen. At last the FEL can be expressed as a function of the initial flexural stiffness, frequency and temperature. Obviously, this procedure has the potential to be very useful in view of long-life pavement design and time consuming traditional fatigue tests.展开更多
文摘Coronary artery calcium data and reporting system(CAC-DRS)is a recently introduced standardized reporting system for calcium scoring on computed tomography.CAC-DRS provides four risk categories(0,1,2 and 3)along with treatment recommendations for each category.As with any other new reporting platform,CAC-DRS has both advantages and disadvantages.Improved communication,better clarity of details,organized management recommendations and utility in future research and education are the major strengths of CAC-DRS.It has many limitations such as questionable need for a new system,few missing components,use of a less accurate visual method and treatment suggestions based on expert opinion instead of clinical trials.In this contemporary review,we discuss the new reporting system CAC-DRS,its application,strengths and limitations and conclude with some remarks for the future.
文摘The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of mining situations. While common wisdom sensibly limits the use of the resultant pillar strength equations and methods to design scenarios that are consistent with the founding database, there are a number of examples where failures have occurred as a direct result of applying empirical design methods to coal pillar design problems that are inconsistent with the founding database. This paper explores the reasons why empirically derived coal pillar strength equations tend to be problem-specific and should be considered as providing no more than a pillar strength ‘‘index." These include the non-consideration of overburden horizontal stress within the mine stability problem, an inadequate definition of supercritical overburden behavior as it applies to standing coal pillars, and the non-consideration of overburden displacement and coal pillar strain limits. All of which combine to potentially complicate and confuse the back-analysis of coal pillar strength from failed cases. A modified coal pillar design representation and model are presented based on coal pillars acting to reinforce a horizontally stressed overburden, rather than suspend an otherwise unstable self-loaded overburden or section, the latter having been at the core of historical empirical studies into coal pillar strength and stability.
文摘Overhanging rock slopes(steeper than 90°) are typically avoided in rock engineering design, particularly where the scale of the slope exceeds the scale of fracturing present in the rock mass. This paper highlights an integrated approach of designing overhanging rock slopes where the relative dimensions of the slope exceed the scale of fracturing and the rock mass failure needs to be considered rather than kinematic release of individual blocks. The key to the method is a simplified limit equilibrium(LE) tool that was used for the support design and analysis of a multi-faceted overhanging rock slope. The overhanging slopes required complex geometries with constantly changing orientations. The overhanging rock varied in height from 30 m to 66 m. Geomechanical modelling combined with discrete fracture network(DFN)representation of the rock mass was used to validate the rock mass strength assumptions and the failure mechanism assumed in the LE model. The advantage of the simplified LE method is that buttress and support design iterations(along with sensitivity analysis of design parameters) can be completed for various cross-sections along the proposed overhanging rock sections in an efficient manner, compared to the more time-intensive, sophisticated methods that were used for the initial validation. The method described presents the development of this design tool and assumptions made for a specific overhanging rock slope design. Other locations will have different geological conditions that can control the potential behaviour of rock slopes, however, the approach presented can be applied as a general guiding design principle for overhanging rock cut slope.
文摘The surface yield strength(σ_(ms))for various carbon steels was studied by means of X-ray diffraction method.The results showed that it is.far below the bulk yield strength,and is the resistance against plastic deformation in the surface layer.The smooth fatigue limit is associ- ated with crack initiation which is a result of accumulation of plastic deformation.Experimen- tal results showed the relation of smooth fatigue limit for 50% survival with σ_(ms)is σ_(ms)=0.81 tO 1.02 σ_(-1)for different steels.The smooth fatigue limit of a medium carbon steel for 99.9% survival with σ_(ms)is σ_(ms)=0.98 tO 1.10 σ_(-1).It is less expensive and time consuming to measure σ_(ms)than σ_(-1).
文摘With applied dislocation theory,the effects of shear and normal stresses on the slide and climb motions at the same section of a crystal were analyzed.And,based on the synergetic effect of both normal and shear strain specific energies,the concept of the total equivalent strain specific energy(TESSE)at an oblique section and a new strength theory named as limiting strain energy strength theory(LSEST)were proposed.As for isotropic materials,the plastic yielding or brittle fracture of under uniaxial stress state would occur when the maximum TESSE reached the strain specific energy,also the expressions on the equivalent stresses and a function of failure of the LSEST under different principal stress states were obtained.Relationship formulas among the tensile, compressive and shear yield strengths for plastic metals were derived.These theoretical predictions,according to the LSEST,were consistent very well with experiment results of tensile,compressive and torsion tests of three plastic metals and other experiment results from open literatures.This novel LSEST might also help for strength calculation of other materials.
基金funded by the Scientific Research and Development Projects of China Railway Corporation(2011J105-B)
文摘Resistance multi-spot welding （MSW） in column, triangle and tetragonal symmetry arrangements was prepared using cold-rolled 301L high-strength sheets, and their static and fatigue properties were in- vestigated. The effects of spot welds on the fracture strengths and fatigue limits were discussed. The results show that the static strengths can be estimated using an inherent linear relationship formula of the load versus the welding area. It was based on the 28%-33% volume fraction of α′ martensite induced at the interfacial spot weld fracture because of the failure deformation. The fatigue limits of the MSW nonlin- early increase with the number of spot welds. The arrangement of spot welds in the MSW significantly affects the average fatigue limit of each spot weld; its 26% maximum reduction occurred in the triangle, and the interaction stress between spot welds led to its 18% reduction in the tetragonal symmetry. The calculated fatigue stress of all MSW loadings with their mean fatigue limits was 230-270 MPa.
基金Supported by the National Natural Science Foundation of China (40318002)
文摘The finite element limit analysis method has the advantages of both numerical and traditional limit equilibrium techniques and it is particularly useful to geotechnical engineering.This method has been developed in China,following well-accepted international procedures,to enhance understanding of stability issues in a number of geotechnical settings.Great advancements have been made in basic theory,the improvement of computational precision,and the broadening of practical applications.This paper presents the results of research on（1） the efficient design of embedded anti-slide piles,（2） the stability analysis of reservoir slopes with strength reduction theory,and（3） the determination of the ultimate bearing capacity of foundations using step-loading FEM（overloading）.These three applications are evidence of the design improvements and benefits made possible in geotechnical engineering by finite element modeling.
基金ThisresearchprojectwasfinanciallysupportedbytheMinistryofScienceandTechnology Japan (DomesticResearchFellowship 1999 2 0 0 1) .
文摘Extensive data of undrained shear strength for various remolded soils are compiled to normalize the remolded undrained strength. Remolded soils have a wide spectrum of liquid limits ranging from 25% to 412%. It is found that the remolded undrained strength is a function of water content and liquid limit. Furthermore, a simple index designated as normalized water content w * is introduced for normalizing remolded undrained strength for various soils. The normalized water content w * is the ratio of water content to liquid limit. The relationship between the remolded undrained strength and the normalized water content can be expressed by a simple equation. The new simple equation is not only valuable theoretically for helping in assessing the in situ mechanical behavior, but also useful to ocean engineering practice.
基金Sponsored by the National Natural Science Foundation of China(Grant No.50878037,51078059,51178078)
文摘This paper presents the results of four partially prestressed ultra-high strength concrete beams in flexure. The test results are used to evaluate the effects of prestressing tendon depth and area on flexure behavior of specimen beams. The test results indicate that: the cracking load,yielding load,peak load and stiffness postcracking of specimen beams are enhanced by reducing prestressing tendon depth or increasing prestressing tendon area, and the flexural ductility is improved by increasing prestressing tendon depth or reducing prestressing tendon area. The effect of complex reinforcement index considering the strength of the equivalence principle and the reinforcement position on loading levels under serviceability limit state,flexural strength and displacement ductility factor are studied. The influence coefficient of prestressing tendon kpis introduced in the complex reinforcement index. As the complex reinforcement index increases, the loading levels under serviceability limit state and flexural strength increases linearly,and the displacement ductility factor decreases linearly. The test results also verify the conventional beam flexural theory based on the plane cross-section assumption for predicting ultimate flexural strength of partially prestressed ultra-high strength concrete beams is valid. After the introduction of the coefficient kp,the calculation method of cracks in code for design of concrete structure in china are appropriated for the specimen beams.
文摘Structural analysis of steel frames is typically performed using beam elements. Since these elements are unable to explicitly capture the local buckling behavior of steel cross-sections, traditional steel design specifications use the concept of cross-section classification to determine the extent to which the strength and deformation capacity of a cross-section are affected by local buckling. The use of plastic design methods are restricted to Class 1 cross-sections, which possess sufficient rotation capacity for plastic hinges to develop and a collapse mechanism to form. Local buckling prevents the development of plastic hinges with such rotation capacity for cross-sections of higher classes and, unless computationally demanding shell elements are used, elastic analysis is required. However, this article demonstrates that local buckling can be mimicked effectively in beam elements by incorporating the continuous strength method (CSM) strain limits into the analysis. Furthermore, by performing an advanced analysis that accounts for both geometric and material nonlinearities, no additional design checks are required. The positive influence of the strain hardening observed in stocky cross-sections can also be harnessed, provided a suitably accurate stress–strain relationship is adopted;a quad-linear material model for hot-rolled steels is described for this purpose. The CSM strain limits allow cross-sections of all slenderness to be analyzed in a consistent advanced analysis framework and to benefit from the appropriate level of load redistribution. The proposed approach is applied herein to individual members, continuous beams, and frames, and is shown to bring significant benefits in terms of accuracy and consistency over current steel design specifications.
文摘Stress-strength model is a basic and important tool for reliability analysis.There are few methods to assess the confidence limit of interference reliability when the distribution parameters of stress and strength are all unknown.A new assessment method of interference reliability is proposed and the estimates of the distribution parameters are accordingly given.The lower confidence limit of interference reliability with given confidence can be obtained with the method even though the parameters are all unknown.Simulation studies and an engineering application are conducted to validate the method,which suggest that the method provides precise estimates even for sample size of approximately.
文摘The present paper aims at giving some general ideas concerning the micromechanical approach of the strength of a porous material. It is shown that its determination theoretically amounts to solving a nonlinear boundary value problem defined on a representative elementary volume(REV). The principle of nonlinear homogenization is illustrated based on the case of a solid phase having a Green’s strength criterion. An original refinement of the so-called secant method(based on two reference strains) is also provided. The paper also describes the main feature of the Gurson’s model which implements the principle of limit analysis on a conceptual model of hollow sphere. The last part of the paper gives some ideas concerning poromechanical couplings.
文摘A simplified procedure was described to estimate the FEL of three kinds of hot-mix asphalt concrete （HMAC） without doing any fatigue tests. The procedure required two fundamental properties of HMAC, tensile strength under different temperatures and strain rates, and flexural stiffness under different stain levels. This information can reliably be obtained in simple tests, which are the monotonic uniaxial tensile test （MUTT） and the four-point bending test （FPBT）. A new parameter, the initial stress ratio Rinitial, was introduced to connect these two tests, which was defined as the ratio of applied initial stress and tensile strength of the specimen. At last the FEL can be expressed as a function of the initial flexural stiffness, frequency and temperature. Obviously, this procedure has the potential to be very useful in view of long-life pavement design and time consuming traditional fatigue tests.
