To investigate the damage evolution caused by stress-driven and sub-critical crack propagation within the Beishan granite under multi-creep triaxial compressive conditions,the distributed optical fiber sensing and X-r...To investigate the damage evolution caused by stress-driven and sub-critical crack propagation within the Beishan granite under multi-creep triaxial compressive conditions,the distributed optical fiber sensing and X-ray computed tomography were combined to obtain the strain distribution over the sample surface and internal fractures of the samples.The Gini and skewness(G-S)coefficients were used to quantify strain localization during tests,where the Gini coefficient reflects the degree of clustering of elements with high strain values,i.e.,strain localization/delocalization.The strain localization-induced asymmetry of data distribution is quantified by the skewness coefficient.A precursor to granite failure is defined by the rapid and simultaneous increase of the G-S coefficients,which are calculated from strain increment,giving an earlier warning of failure by about 8%peak stress than those from absolute strain values.Moreover,the process of damage accumulation due to stress-driven crack propagation in Beishan granite is different at various confining pressures as the stress exceeds the crack initiation stress.Concretely,strain localization is continuous until brittle failure at higher confining pressure,while both strain localization and delocalization occur at lower confining pressure.Despite the different stress conditions,a similar statistical characteristic of strain localization during the creep stage is observed.The Gini coefficient increases,and the skewness coefficient decreases slightly as the creep stress is below 95%peak stress.When the accelerated strain localization begins,the Gini and skewness coefficients increase rapidly and simultaneously.展开更多
A multi-stage stress relaxation test was performed on a granodiorite sample to understand the deformation process prior to the macroscopic failure of brittle rocks,as well as the transient response during stress relax...A multi-stage stress relaxation test was performed on a granodiorite sample to understand the deformation process prior to the macroscopic failure of brittle rocks,as well as the transient response during stress relaxation.Distributed optical fiber sensing was used to measure strains across the sample surface by helically wrapping the single-mode fiber around the cylindrical sample.Close agreement was observed between the circumferential strains obtained from the optical fibers and the extensometer.The reconstructed full-field strain contours show strain heterogeneity from the crack closure phase,and the strains in the later deformation phase are dominantly localized within the former high-strain zone.The Gini coefficient was used to quantify the degree of strain localization and shows an initial increase during the crack closure phase,a decrease during the linear elastic phase,and a subsequent increase during the post-yielding phase.This behavior corresponds to a process of initial localization from an imperfect boundary condition,homogenization,and eventual relocalization prior to the macroscopic failure of the sample.The transient strain rate decay during the stress relaxation phase was quantified using the p-value in the“Omori-like"power law function.A higher initial stress at the onset of relaxation results in a lower p-value,indicating a slower strain rate decay.As the sample approaches macroscopic failure,the lowest p-value shifts from the most damaged zone to adjacent areas,suggesting stress redistribution or crack propagation in deformed crystalline rocks under stress relaxation conditions.展开更多
Granular materials exhibit complex macroscopic mechanical behaviors closely related to their microscalemicrostructural features.Traditional macroscopic phenomenological elasto-plastic models,however,usually have compl...Granular materials exhibit complex macroscopic mechanical behaviors closely related to their microscalemicrostructural features.Traditional macroscopic phenomenological elasto-plastic models,however,usually have complex formulations and lack explicit relations to these microstructural features.To avoid these limitations,this study proposes a micromechanics-based softening hyperelastic model for granular materials,integrating softening hyperelasticity withmicrostructural insights to capture strain softening,critical state,and strain localization behaviors.The model has two key advantages:(1)a clear conceptualization,straightforward formulation,and ease of numerical implementation(via Abaqus UMAT subroutine in this study);(2)explicit incorporation of micro-scale features(e.g.,contact stiffness,particle size,porosity)to reveal their influences on macroscopic responses.An isotropic directional distribution density of contacts and three specific microstructures are considered,and their softening hyperelastic constitutive modulus tensors are explicitly derived.By introducing a softening factor and critical failure energy density,the model can describe geomaterial behaviors,simulating residual strength,X-shaped shear bands,and strain localization evolution.Numerical validations in comparison with themacro-scale hyperelastic model,Abaqus Drucker-Prager model,and the experiment confirm its accuracy.Parametric studies reveal critical dependencies:a normal to tangential contact stiffness ratio of 2-8(depending on stiffness magnitude),an internal length of 2-4 mm to ensure shear band formation,and a critical failure energy density(≤10 kJ/m^(3))to trigger strain softening and localization.Influences of the specific microstructures on strain localization and softening are investigated.The model also shows mesh independence due to the introduction of an internal length.The model’s applicability is further demonstrated by slope stability analysis,capturing slip surface evolution,and load-displacement characteristics.This study develops a robust microstructure-aware hyperelastic framework to describe the mechanical behaviors of granular materials,providing multiscale insights for geotechnical engineering applications.展开更多
The study of rock failure mechanisms is fundamental to geotechnical engineering,as it enhances design quality and mitigates disaster risks.This research employed in situ compression tests on 3D-printed rocklike sample...The study of rock failure mechanisms is fundamental to geotechnical engineering,as it enhances design quality and mitigates disaster risks.This research employed in situ compression tests on 3D-printed rocklike samples with a single flaw,combining Micro-CT scans and a specialized loading device to analyze their behavior.Mechanical properties and failure modes of these printed samples were compared to those of natural flawed sandstones,demonstrating the capability of 3D printing to replicate natural rock characteristics.By reconstructing 3D crack evolution from 2D CT images and applying digital volume correlation(DVC),the study visualized internal strain fields and established a relationship between strain patterns and rock failure.The results reveal that crack initiation consistently occurs at the flaw,advancing into tensile and secondary shear or mixed cracks.For flaw angles(α)ranging from 0°to 45°,the 3D-printed samples exhibited a higher number of newly formed cracks and a faster increase in crack volume with strain.In contrast,for flaw angles of 45°≤α≤90°,the opposite trend was observed.The internal strain field exhibited significant strain localization,with this uneven distribution playing a critical role in sample failure.When the flaw angle was in the range of 0°≤α≤30°,failure was primarily driven by tensile cracks,forming distinct tensile bands.Conversely,for 30°<α≤90°,a combination of tensile and shear cracks dominated the failure,producing both shear and tensile bands in the sample.Additionally,the strain field component ε_(yy) showed a strong correlation with the evolution of internal damage,providing valuable insights into the underlying rock failure mechanisms.展开更多
A kind of slow deformation wave is produced in the crust under the action of internal and external factors,which plays an important role in the formation and occurrence of earthquakes.In this paper,uniaxial compressio...A kind of slow deformation wave is produced in the crust under the action of internal and external factors,which plays an important role in the formation and occurrence of earthquakes.In this paper,uniaxial compression tests are carried out on red sandstone samples with uniform texture.Displacement controlled loading methods are adopted,and the loading rates are 0.1 mm/min,0.5 mm/min and 1.0 mm/min,respectively.The micro-characterization method of speckle photography and DIC processing technology are adopted.The transfer characteristics of slow deformation and strain localization of red sandstone specimens during loading and deformation are discussed.The results show that the boundary advance velocity is proportional to the slow deformation transfer velocity with the change of position,so it can be considered that the slow deformation transfer velocity is equal to the particle motion transfer velocity.The formation and development of sample strain localization may be determined by the flow channel,nucleation and Luders zone evolution.The formation of the Luders band is related to the maximum value of the flow channel,and as deformation increases,the Luders band merges and develops with the maximum value of the nearby flow channel.By applying different loading rates,the influence of loading rate on the average transfer velocity of slow deformation was obtained;the slow deformation wave during seismic migration has similar characteristics to the deformation transfer in the experiment,therefore the research results have reference significance for further studies on the evolution characteristics of slow deformation waves and seismic migration.展开更多
Background and Objectives:The perception of sound in the vertical plane supports spatial hearing by enabling listeners to detect sources located above and below.Sounds originating from both the front and back elevatio...Background and Objectives:The perception of sound in the vertical plane supports spatial hearing by enabling listeners to detect sources located above and below.Sounds originating from both the front and back elevations along the mid-sagittal plane further contribute to a three-dimensional auditory experience.This study aimed to characterize the variability in vertical sound localization abilities among normal-hearing(NH)individuals using spatialized audio.Materials and Methods:Fifty-one NH participants(aged 18 to 35 years)completed three vertical localization tasks under headphones as part of a single-group,within-subject experimental study.These tasks included two-plane identification:(1)top-down localization,(2)front-back localization,and one discrimination task in the front plane.Hierarchical Cluster Analysis(HCA)was employed to identify distinct patterns in spatial localization profiles specific to the vertical-median plane.Fisher's Discriminant Function Analysis(FDA)was used to validate the accuracy of HCA and estimate classification error.Results:HCA revealed three distinct listener clusters:(1)cluster 1 with good performance across all three tasks,(2)cluster 2 with selective impairment in top-bottom identification,and(3)cluster 3 with selective deficits in front-back identification.FDA validated group membership of the clusters identified by the HCA,with a prediction accuracy of 98%.Conclusions:Individuals with clinically NH exhibited three distinct vertical localization profiles:uniform performers,those impaired in top-bottom identification,and those impaired in front-back identification.These profiles may be linked to the interplay between acoustic and non-acoustic perceptual factors.展开更多
Owing to their good biocompatibility,polysaccharide hydrogels have broad application prospects in the field of flexible strain sensors.However,there are still significant challenges in the preparation of polysaccharid...Owing to their good biocompatibility,polysaccharide hydrogels have broad application prospects in the field of flexible strain sensors.However,there are still significant challenges in the preparation of polysaccharide hydrogels with good mechanical properties.MCA-Li Cl hydrogels were prepared by introducing methacrylated hyaluronic acid(Me HA)into the polymer network in the presence of acrylic acid(AA),acryloyloxyethyltrimethyl ammonium chloride(CATAC),and metal ions.The polymer network not only has a chemically cross-linked network and a tough network structure,but also benefits from a variety of supramolecular interactions,such as hydrogen bonding and coordination covalent bonding,resulting in excellent mechanical properties,with an elongation at break of 1390%,a tensile strength of up to 1200 k Pa,a toughness of 9.4546 MJ/m^(3),and adhesive properties towards various substrates.At the same time,the hydrogel has a high conductivity(5.33 mS/cm)and high strain-sensing sensitivity(Gauge factor=2.55).The flexible strain sensor assembled from the prepared MCA-Li Cl hydrogel can be used to detect human movements,from micro-expressions(smiles,swallowing)to pulse signals and other physiological activities,as well as large-scale joint movements(wrists,elbows,knees,fingers,etc.),realizing the real-time monitoring of full-scale human movements.The prepared hydrogels have potential applications in wearable devices,electronic skin,and strain-sensor components.展开更多
Single-crystal GaN epilayers were irradiated with heavy inert gas ions(2.3-MeV Ne^(8+),5.3-MeV Kr^(19+))to fluences ranging from 1.0×1.0^(11) to 1.0×1.0^(15)ions∕cm^(2).The strain-related damage accumulatio...Single-crystal GaN epilayers were irradiated with heavy inert gas ions(2.3-MeV Ne^(8+),5.3-MeV Kr^(19+))to fluences ranging from 1.0×1.0^(11) to 1.0×1.0^(15)ions∕cm^(2).The strain-related damage accumulation versus ion fluences was studied using highresolution X-ray diffraction(HRXRD)and ultraviolet–visible(UV–Vis)spectroscopy.The results showed that the damage accumulation was mainly dominated by nuclear energy loss.When the ion fluence was less than∼0.055 displacement per atom(dpa),the lattice expansions and lattice strains markedly increased linearly with increasing ion fluences,accompanied by a slow enhancement in the dislocation densities,distortion parameters,and Urbach energy for both ion irradiations.Above this fluence(∼0.055 dpa),the lattice strains presented a slight increase,whereas a remarkable increase was observed in the dislocation densities,distortion parameters,and Urbach energy with the ion fluences after both ion irradiations.∼0.055 dpa is the threshold ion fluence for defect evolution and lattice damage related to strain.The mechanisms underlying the damage accumulation are discussed in detail.展开更多
This paper proposes a tamper detection technique for semi-fragile watermarking using Quantizationbased Discrete Cosine Transform(DCT)for tamper localization.In this study,the proposed embedding strategy is investigate...This paper proposes a tamper detection technique for semi-fragile watermarking using Quantizationbased Discrete Cosine Transform(DCT)for tamper localization.In this study,the proposed embedding strategy is investigated by experimental tests over the diagonal order of the DCT coefficients.The cover image is divided into non-overlapping blocks of size 8×8 pixels.The DCT is applied to each block,and the coefficients are arranged using a zig-zag pattern within the block.In this study,the low-frequency coefficients are selected to examine the impact of the imperceptibility score and tamper detection accuracy.High accuracy of tamper detection can be achieved by checking the surrounding blocks to determine whether the corresponding block has been tampered with.The proposed tamper detection is tested under various malicious,incidental,and hybrid attacks(both incidental and malicious attacks).The experimental results demonstrate that the proposed technique achieves a Peak-Signal-to-Noise Ratio(PSNR)value of 41.2318 dB,an average Structural Similarity Index Measure(SSIM)value of 0.9768.The proposed scheme is also evaluated against malicious attacks such as copy-move,object deletion,object manipulation,and collage attacks.The proposed scheme can detect the malicious attack localization under various tampering rates.In addition,the proposed scheme can still detect tampered pixels under a hybrid attack,such as a combination ofmalicious and incidental attacks,with an average accuracy of 96.44%.展开更多
The acquisition of position information of legitimate users and jammers plays an important role in the emerging non-geostationary synchronous orbit(NGSO)satellite communications.In this paper,we study the multi-signal...The acquisition of position information of legitimate users and jammers plays an important role in the emerging non-geostationary synchronous orbit(NGSO)satellite communications.In this paper,we study the multi-signal localization problem in an uplink NGSO satellite communication system.We propose an onboard localization scheme based on multiple observations from the satellite,together with the geometric constraints of the satellite postions,the signal positions,the attitude of the satellite,and the angle-of-arrival(AoAs)of the signals.We develop a massage-passing algorithm,termed the Bayesian blind multi-signal localization(BMSL),to jointly estimate the AoAs and the signal positions.The Cramér-Rao lower bound(CRLB)is derived to characterize the fundamental performance limit of the considered localization problem.Simulation results show that the proposed BMSL algorithm can perform close to the derived CRLB and significantly outperforms its counterpart algorithms.展开更多
The stator of the maglev track plays a crucial role in the operation of the maglev system.Currently,the efficiency of maglev track inspection is limited by several factors,including the large span of elevated structur...The stator of the maglev track plays a crucial role in the operation of the maglev system.Currently,the efficiency of maglev track inspection is limited by several factors,including the large span of elevated structures,manual visual inspection,short inspection window times,and limited GPS positioning accuracy.To address these issues,this paper proposes a deep learning-based method for detecting and locating stator surface damage.This study establishes a maglev track stator surface image dataset,trains different object detection models,and compares their performance.Ultimately,YOLO and ByteTrack object tracking algorithms were chosen as the basic framework and enhanced to achieve automatic identification of high-speed maglev track stator surface damage images and track and count stator surface localization feature images.By matching the identified damaged images with their corresponding stator segment and beam segment sequence numbers,the location of the damage is pinpointed to the corresponding stator segment,enabling rapid and accurate identification and localization of complex damage to the maglev track stator surface.展开更多
Large magnetic entropy change(△S_(M))can realize a prominent heat transformation under the magnetic field and directly strengthen the efficacy of the magnetocaloric effect,which provides a pioneering environmentally ...Large magnetic entropy change(△S_(M))can realize a prominent heat transformation under the magnetic field and directly strengthen the efficacy of the magnetocaloric effect,which provides a pioneering environmentally friendly solidstate strategy to improve refrigeration capacities and efficiencies.The second-order magnetic transition(SOMT)materials have broader△S_(M) peaks without thermal hysteresis,making them highly attractive in magnetic refrigeration,especially in the room temperature range.Here,we report a significant enhancement of△S_(M) at room temperature in single-crystal Mn_(5)Ge_(3).In this SOMT system,we realize a 60%improvement of-△S_(M)^(max) from 3.5 J/kg·K to 5.6 J/kg·K at T=300 K.This considerable enhancement of△S_(M) is achieved by intentionally introducing strain energy through high-pressure constrained deformation.Both experimental results and Monte Carlo simulations demonstrate that the enhancement of△S_(M) originates from the microscopic strain and lattice deformation induced by strain energy after deformation.This strain energy will reconstruct the energy landscape of this ferromagnetic system and enhance magnetization,resulting in a giant intensity of magnetocaloric responses.Our findings provide an approach to increase magnetic entropy change and may give fresh ideas for exploring advanced magnetocaloric materials.展开更多
This paper develops a semi-analytical solution for pile penetration in natural soft clays using the strain path method(SPM).The stress-strain behavior of soils is characterized by the S-CLAY1S model,which can capture ...This paper develops a semi-analytical solution for pile penetration in natural soft clays using the strain path method(SPM).The stress-strain behavior of soils is characterized by the S-CLAY1S model,which can capture the anisotropic evolution and destructuring nature of soft clays.By integrating the S-CLAY1S model into the theoretical framework of the SPM,a set of ordinary differential equations is formulated with respect to the vertical coordinate of soil particles.The distribution of excess pore water pressure(EPWP)following pile installation is approximated through one-dimensional(1D)radial integration around the pile shaft.The distribution of stresses and EPWP,along with the evolution of fabric anisotropy within the soil surrounding the pile,is presented to illustrate the response of pile penetration in natural soft clays.The proposed solution is validated against existing theoretical solutions using the SPM and cavity expansion method(CEM),along with experimental data.The findings demonstrate that the SPM reveals lower radial effective stresses and EPWP at the pile shaft than that of CEM.Pile penetration alters the soil's anisotropic properties,inducing rotational hardening and affecting post-installation stress distribution.Soil destructuration eliminates bonding among particles near the pile,resulting in a complete disruption of soil structure at the pile surface,which is particularly pronounced for higher initial soil structure ratios.Minimal variation was observed in the three principal stresses and shear stress on the cone side surface as the angle increased from 18°to 60°,except for a slight reduction in EPWP.展开更多
High-performance fiber fabrics and composites experienced transverse compression deformation at ultrahigh strain rates near the impact point when subjected to high-velocity impacts,which significantly affected their b...High-performance fiber fabrics and composites experienced transverse compression deformation at ultrahigh strain rates near the impact point when subjected to high-velocity impacts,which significantly affected their ballistic limits.In this paper,a fiber-scale experimental method for characterizing ultrahigh strain-rate transverse compression behavior was proposed.To begin with,in order to measure the extremely low stress and strain in small specimens,the conventional Hopkinson bar was reduced to the hundred-micron scale,thereby achieving wave impedance matching with single fibers.In addition,tangential and normal laser Doppler velocimetry(LDV)methods were employed to realize non-contact,high-precision,and high-speed axial velocity measurements of micron-scale incident and transmission bars,respectively.Meanwhile,a microscopic observation system was used to facilitate the installation of miniature fiber samples.The experimental setup and procedures were introduced,and the system accuracy was verified through sample-free loading tests based on one-dimensional stress wave propagation theory.Dynamic compression experiments on Graphene-UHMWPE fibers were carried out,followed by post-compression microstructural characterization via scanning electron microscopy(SEM).Results demonstrated that successful mechanical characterization was achieved at strain rates exceeding 105,an order of magnitude higher than the previously reported maximum rates.Furthermore,during the loading process,the fibers underwent uniform compression deformation while exhibiting pronounced strain-rate effects.This method offers a novel approach for dynamic mechanical characterization of microscale single fibers,enabling the development of comprehensive strain-ratedependent material models to guide the design of advanced composites and high-performance fibers.展开更多
High-performance intelligent protective materials are vital for nuclear energy systems exposed to extreme irradiation.Among them,tungsten-based alloys demonstrate exceptional potential owing to their superior irradiat...High-performance intelligent protective materials are vital for nuclear energy systems exposed to extreme irradiation.Among them,tungsten-based alloys demonstrate exceptional potential owing to their superior irradiation resistance.Recent experimental studies have demonstrated that W-Ta-Cr-V alloys exhibit excellent irradiation resistance under helium(He)ion irradiation.However,the underlying mechanisms,especially the migration behavior of He atoms,remain unclear.In this work,the influences of uniaxial tensile and compressive strain on He migration in W-Ta-Cr-V complex alloys have been systematically studied through first-principles calculations.Our results demonstrate that He atoms preferentially occupy the tetrahedral interstitial sites,with interstitial formation energies significantly reduced compared to pure W.The introduction of Ta,Cr,and V alloying elements markedly increases the He migration barriers,effectively suppressing He diffusion.Compressive strain increases the migration barriers,inhibiting He bubbles nucleation and growth,while tensile strain decreases the barriers,facilitating bubble formation.Compared to pure W,the W-Ta-Cr-V alloys exhibit both lower He interstitial formation energies and higher migration barriers,with further enhancement under compressive strain.Specifically,compressive strain of 6%increases the He migration barrier of the W-Ta-Cr-V alloy by 0.166 e V,which further widens the difference relative to pure W.These findings provide a theoretical explanation for the superior irradiation resistance of tungsten-based alloys observed experimentally and promote the understanding of irradiation damage in these alloys under strain.展开更多
Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study el...Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study elucidates the fundamental mechanisms of ultrafast laser shock imprinting(LSI)in two-dimensional tellurium(Te),establishing a direct relationship between strain field orientation,mold topology,and anisotropic structural evolution.This is the first demonstration of ultrafast LSI on chiral chain Te unveiling orientation-sensitive dislocation networks.By applying controlled strain fields parallel or transverse to Te’s helical chains,we uncover two distinct deformation regimes.Strain aligned parallel to the chain’s direction induces gliding and rotation governed by weak interchain interactions,preserving covalent intrachain bonds and vibrational modes.In contrast,transverse strain drives shear-mediated multimodal deformations—tensile stretching,compression,and bending—resulting in significant lattice distortions and electronic property modulation.We discovered the critical role of mold topology on deformation:sharp-edged gratings generate localized shear forces surpassing those from homogeneous strain fields via smooth CD molds,triggering dislocation tangle formation,lattice reorientation,and inhomogeneous plastic deformation.Asymmetrical strain configurations enable localized structural transformations while retaining single-crystal integrity in adjacent regions—a balance essential for functional device integration.These insights position LSI as a precision tool for nanoscale strain engineering,capable of sculpting 2D material morphologies without compromising crystallinity.By bridging ultrafast mechanics with chiral chain material science,this work advances the design of strain-tunable devices for next-generation electronics and optoelectronics,while establishing a universal framework for manipulating anisotropic 2D systems under extreme strain rates.This work discovered crystallographic orientation-dependent deformation mechanisms in 2D Te,linking parallel strain to chain gliding and transverse strain to shear-driven multimodal distortion.It demonstrates mold geometry as a critical lever for strain localization and dislocation dynamics,with sharp-edged gratings enabling unprecedented control over lattice reorientation.Crucially,the identification of strain field conditions that reconcile severe plastic deformation with single-crystal retention offers a pathway to functional nanostructure fabrication,redefining LSI’s potential in ultrafast strain engineering of chiral chain materials.展开更多
Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The t...Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.展开更多
Microorganisms are crucial for the breakdown of proteins and lipids in dry-fermented sausages and are intimately associated with the flavor profile of sausages.In this study,we used a mixed starter culture to ferment ...Microorganisms are crucial for the breakdown of proteins and lipids in dry-fermented sausages and are intimately associated with the flavor profile of sausages.In this study,we used a mixed starter culture to ferment sausages and investigated the flavor turnover.During the fermentation of salami,the data from free amino acids(FAAs),free fatty acids(FFAs)and volatile flavor substances were used to assess the quality of salami.At the end of fermentation,the total FAAs increased from 1171.32 to 4582.48 mg/kg in the control group and 5053.25 mg/kg in the experimental group.Additionally,following inoculation with the mixed starter culture,the levels of glutamic acid,lysine,methionine,valine and leucine were significantly higher(P<0.05)than those in the control group.Oleic acid(C_(18:1))and chondritic acid(C_(16:0))were the two most abundant FFAs in both salami samples with 45.86%and 26.07%on the 23^(th)day in mixed culture inoculated salami.The mixed starter inoculated group had significantly lower saturated fatty acids and higher percentage levels of monounsaturated fatty acids than the control group(P<0.05).In the volatile flavor substance analysis,a total of 61 volatile compounds were found.Ester compounds were progressively enriched with drying time,significantly increasing the flavor substances,like ethyl diphosgene,1-octen-3-ol,and 2,3-butanediol at P<0.05.The correlation analysis between the core flora and volatile flavor compounds during fermentation and maturation of salami indicates Lactobacillus sakei and Lactobacillus rhamnosus were significantly higher and positively correlated with the major volatile organic compounds,which are the key core microorganisms affecting the flavor quality of fermented sausages.展开更多
Reconfigurable intelligent surfaces(RISs)not only assist communication but also help the localization of user equipment(UE).This study focuses on indoor localization of UE with a single access point(AP)and multiple RI...Reconfigurable intelligent surfaces(RISs)not only assist communication but also help the localization of user equipment(UE).This study focuses on indoor localization of UE with a single access point(AP)and multiple RISs.First,we propose a two-stage channel estimation scheme where RIS phase shifts are tuned to obtain multiple channel soundings.In the first stage,the newtonized orthogonal matching pursuit algorithm extracts the parameters of multiple paths from the received signals.Then,the LOS path and RISreflected paths are identified.In the second stage,the estimated path gains of RIS-reflected paths with different phase shifts are utilized to determine the angle of arrival(AOA)at the RIS by obtaining the angular pseudo spectrum.Consequently,by taking the AP and RISs as reference points,the linear least squares estimator can locate UE with the estimated AOAs.Simulation results show that the proposed algorithm can realize centimeter-level localization accuracy in the discussed scenarios.Moreover,the higher accuracy of pseudo spectrum,a larger number of channel soundings,and a larger number of reference points can realize higher localization accuracy of UE.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.52339001).
文摘To investigate the damage evolution caused by stress-driven and sub-critical crack propagation within the Beishan granite under multi-creep triaxial compressive conditions,the distributed optical fiber sensing and X-ray computed tomography were combined to obtain the strain distribution over the sample surface and internal fractures of the samples.The Gini and skewness(G-S)coefficients were used to quantify strain localization during tests,where the Gini coefficient reflects the degree of clustering of elements with high strain values,i.e.,strain localization/delocalization.The strain localization-induced asymmetry of data distribution is quantified by the skewness coefficient.A precursor to granite failure is defined by the rapid and simultaneous increase of the G-S coefficients,which are calculated from strain increment,giving an earlier warning of failure by about 8%peak stress than those from absolute strain values.Moreover,the process of damage accumulation due to stress-driven crack propagation in Beishan granite is different at various confining pressures as the stress exceeds the crack initiation stress.Concretely,strain localization is continuous until brittle failure at higher confining pressure,while both strain localization and delocalization occur at lower confining pressure.Despite the different stress conditions,a similar statistical characteristic of strain localization during the creep stage is observed.The Gini coefficient increases,and the skewness coefficient decreases slightly as the creep stress is below 95%peak stress.When the accelerated strain localization begins,the Gini and skewness coefficients increase rapidly and simultaneously.
基金support of her postdoctoral research at the GFZ Helmholtz Centre for Geosciences.P.Pan acknowledges the financial support of the National Natural Science Foundation of China(Grant No.52339001)H.Hofmann and Y.Ji acknowledge the financial support of the Helmholtz Association's Initiative and Networking Fund for the Helmholtz Young Investigator Group ARES(contract number VH-NG-1516).
文摘A multi-stage stress relaxation test was performed on a granodiorite sample to understand the deformation process prior to the macroscopic failure of brittle rocks,as well as the transient response during stress relaxation.Distributed optical fiber sensing was used to measure strains across the sample surface by helically wrapping the single-mode fiber around the cylindrical sample.Close agreement was observed between the circumferential strains obtained from the optical fibers and the extensometer.The reconstructed full-field strain contours show strain heterogeneity from the crack closure phase,and the strains in the later deformation phase are dominantly localized within the former high-strain zone.The Gini coefficient was used to quantify the degree of strain localization and shows an initial increase during the crack closure phase,a decrease during the linear elastic phase,and a subsequent increase during the post-yielding phase.This behavior corresponds to a process of initial localization from an imperfect boundary condition,homogenization,and eventual relocalization prior to the macroscopic failure of the sample.The transient strain rate decay during the stress relaxation phase was quantified using the p-value in the“Omori-like"power law function.A higher initial stress at the onset of relaxation results in a lower p-value,indicating a slower strain rate decay.As the sample approaches macroscopic failure,the lowest p-value shifts from the most damaged zone to adjacent areas,suggesting stress redistribution or crack propagation in deformed crystalline rocks under stress relaxation conditions.
基金supported by the National Natural Science Foundation of China through grant numbers 12002245 and 12172263the Science and Technology Research Program of Chongqing Municipal Education Commission through grant number KJQN202300742+1 种基金the National Natural Science Foundation of ChongqingMunicipality through grant number CSTB2025NSCQ-GPX0841Chongqing Jiaotong University through grant number F1220038.
文摘Granular materials exhibit complex macroscopic mechanical behaviors closely related to their microscalemicrostructural features.Traditional macroscopic phenomenological elasto-plastic models,however,usually have complex formulations and lack explicit relations to these microstructural features.To avoid these limitations,this study proposes a micromechanics-based softening hyperelastic model for granular materials,integrating softening hyperelasticity withmicrostructural insights to capture strain softening,critical state,and strain localization behaviors.The model has two key advantages:(1)a clear conceptualization,straightforward formulation,and ease of numerical implementation(via Abaqus UMAT subroutine in this study);(2)explicit incorporation of micro-scale features(e.g.,contact stiffness,particle size,porosity)to reveal their influences on macroscopic responses.An isotropic directional distribution density of contacts and three specific microstructures are considered,and their softening hyperelastic constitutive modulus tensors are explicitly derived.By introducing a softening factor and critical failure energy density,the model can describe geomaterial behaviors,simulating residual strength,X-shaped shear bands,and strain localization evolution.Numerical validations in comparison with themacro-scale hyperelastic model,Abaqus Drucker-Prager model,and the experiment confirm its accuracy.Parametric studies reveal critical dependencies:a normal to tangential contact stiffness ratio of 2-8(depending on stiffness magnitude),an internal length of 2-4 mm to ensure shear band formation,and a critical failure energy density(≤10 kJ/m^(3))to trigger strain softening and localization.Influences of the specific microstructures on strain localization and softening are investigated.The model also shows mesh independence due to the introduction of an internal length.The model’s applicability is further demonstrated by slope stability analysis,capturing slip surface evolution,and load-displacement characteristics.This study develops a robust microstructure-aware hyperelastic framework to describe the mechanical behaviors of granular materials,providing multiscale insights for geotechnical engineering applications.
基金supported by the Korea Institute of Energy Technology Evaluation and Planning(KETEP)grant funded by the Korea Government(MOTIE)(Grant No.20214000000500,Training program of CCUS for the green growth)by the National Research Foundation of Korea(NRF)grant funded by the Korea Government(MSIT)(Grant No.2022R1F1A1076409)the support from the Chinese Scholarship Council for awarding a scholarship(CSC No.202106820011).
文摘The study of rock failure mechanisms is fundamental to geotechnical engineering,as it enhances design quality and mitigates disaster risks.This research employed in situ compression tests on 3D-printed rocklike samples with a single flaw,combining Micro-CT scans and a specialized loading device to analyze their behavior.Mechanical properties and failure modes of these printed samples were compared to those of natural flawed sandstones,demonstrating the capability of 3D printing to replicate natural rock characteristics.By reconstructing 3D crack evolution from 2D CT images and applying digital volume correlation(DVC),the study visualized internal strain fields and established a relationship between strain patterns and rock failure.The results reveal that crack initiation consistently occurs at the flaw,advancing into tensile and secondary shear or mixed cracks.For flaw angles(α)ranging from 0°to 45°,the 3D-printed samples exhibited a higher number of newly formed cracks and a faster increase in crack volume with strain.In contrast,for flaw angles of 45°≤α≤90°,the opposite trend was observed.The internal strain field exhibited significant strain localization,with this uneven distribution playing a critical role in sample failure.When the flaw angle was in the range of 0°≤α≤30°,failure was primarily driven by tensile cracks,forming distinct tensile bands.Conversely,for 30°<α≤90°,a combination of tensile and shear cracks dominated the failure,producing both shear and tensile bands in the sample.Additionally,the strain field component ε_(yy) showed a strong correlation with the evolution of internal damage,providing valuable insights into the underlying rock failure mechanisms.
基金Postdoctoral Science Fund(043201027)National Natural Science Key Foundation of China(41831290)National Natural Science Foundation of China(52079068).
文摘A kind of slow deformation wave is produced in the crust under the action of internal and external factors,which plays an important role in the formation and occurrence of earthquakes.In this paper,uniaxial compression tests are carried out on red sandstone samples with uniform texture.Displacement controlled loading methods are adopted,and the loading rates are 0.1 mm/min,0.5 mm/min and 1.0 mm/min,respectively.The micro-characterization method of speckle photography and DIC processing technology are adopted.The transfer characteristics of slow deformation and strain localization of red sandstone specimens during loading and deformation are discussed.The results show that the boundary advance velocity is proportional to the slow deformation transfer velocity with the change of position,so it can be considered that the slow deformation transfer velocity is equal to the particle motion transfer velocity.The formation and development of sample strain localization may be determined by the flow channel,nucleation and Luders zone evolution.The formation of the Luders band is related to the maximum value of the flow channel,and as deformation increases,the Luders band merges and develops with the maximum value of the nearby flow channel.By applying different loading rates,the influence of loading rate on the average transfer velocity of slow deformation was obtained;the slow deformation wave during seismic migration has similar characteristics to the deformation transfer in the experiment,therefore the research results have reference significance for further studies on the evolution characteristics of slow deformation waves and seismic migration.
文摘Background and Objectives:The perception of sound in the vertical plane supports spatial hearing by enabling listeners to detect sources located above and below.Sounds originating from both the front and back elevations along the mid-sagittal plane further contribute to a three-dimensional auditory experience.This study aimed to characterize the variability in vertical sound localization abilities among normal-hearing(NH)individuals using spatialized audio.Materials and Methods:Fifty-one NH participants(aged 18 to 35 years)completed three vertical localization tasks under headphones as part of a single-group,within-subject experimental study.These tasks included two-plane identification:(1)top-down localization,(2)front-back localization,and one discrimination task in the front plane.Hierarchical Cluster Analysis(HCA)was employed to identify distinct patterns in spatial localization profiles specific to the vertical-median plane.Fisher's Discriminant Function Analysis(FDA)was used to validate the accuracy of HCA and estimate classification error.Results:HCA revealed three distinct listener clusters:(1)cluster 1 with good performance across all three tasks,(2)cluster 2 with selective impairment in top-bottom identification,and(3)cluster 3 with selective deficits in front-back identification.FDA validated group membership of the clusters identified by the HCA,with a prediction accuracy of 98%.Conclusions:Individuals with clinically NH exhibited three distinct vertical localization profiles:uniform performers,those impaired in top-bottom identification,and those impaired in front-back identification.These profiles may be linked to the interplay between acoustic and non-acoustic perceptual factors.
基金financially supported by the National Natural Science Foundation of China(No.22271074)Natural Science Foundation of Hebei Province(Nos.B2023208042,B2022208032,B2021208066,E2024208084,and E2024208088)+2 种基金Science Research Project of Hebei Education Department(No.JZX2024013)Special Fund for Local Scientific and Technological Development under the Guidance of the Central Government(No.236Z3704G)Hebei Province High Level Talent Funding(No.A202001010)。
文摘Owing to their good biocompatibility,polysaccharide hydrogels have broad application prospects in the field of flexible strain sensors.However,there are still significant challenges in the preparation of polysaccharide hydrogels with good mechanical properties.MCA-Li Cl hydrogels were prepared by introducing methacrylated hyaluronic acid(Me HA)into the polymer network in the presence of acrylic acid(AA),acryloyloxyethyltrimethyl ammonium chloride(CATAC),and metal ions.The polymer network not only has a chemically cross-linked network and a tough network structure,but also benefits from a variety of supramolecular interactions,such as hydrogen bonding and coordination covalent bonding,resulting in excellent mechanical properties,with an elongation at break of 1390%,a tensile strength of up to 1200 k Pa,a toughness of 9.4546 MJ/m^(3),and adhesive properties towards various substrates.At the same time,the hydrogel has a high conductivity(5.33 mS/cm)and high strain-sensing sensitivity(Gauge factor=2.55).The flexible strain sensor assembled from the prepared MCA-Li Cl hydrogel can be used to detect human movements,from micro-expressions(smiles,swallowing)to pulse signals and other physiological activities,as well as large-scale joint movements(wrists,elbows,knees,fingers,etc.),realizing the real-time monitoring of full-scale human movements.The prepared hydrogels have potential applications in wearable devices,electronic skin,and strain-sensor components.
基金supported by the Program for National Natural Science Foundation of China(No.11675231)the Sichuan Science and Technology Program(Nos.2022YFG0263 and 2024NSFSC1097)the Scientific Research Starting Foundation for talents(Nos.21zx7109 and 22zx7175,24ycx1005).
文摘Single-crystal GaN epilayers were irradiated with heavy inert gas ions(2.3-MeV Ne^(8+),5.3-MeV Kr^(19+))to fluences ranging from 1.0×1.0^(11) to 1.0×1.0^(15)ions∕cm^(2).The strain-related damage accumulation versus ion fluences was studied using highresolution X-ray diffraction(HRXRD)and ultraviolet–visible(UV–Vis)spectroscopy.The results showed that the damage accumulation was mainly dominated by nuclear energy loss.When the ion fluence was less than∼0.055 displacement per atom(dpa),the lattice expansions and lattice strains markedly increased linearly with increasing ion fluences,accompanied by a slow enhancement in the dislocation densities,distortion parameters,and Urbach energy for both ion irradiations.Above this fluence(∼0.055 dpa),the lattice strains presented a slight increase,whereas a remarkable increase was observed in the dislocation densities,distortion parameters,and Urbach energy with the ion fluences after both ion irradiations.∼0.055 dpa is the threshold ion fluence for defect evolution and lattice damage related to strain.The mechanisms underlying the damage accumulation are discussed in detail.
基金funded by Ministry of Higher Education Malaysia through Universiti Malaysia Pahang Al-Sultan Abdullah under Internal Research Grant(RDU233003).
文摘This paper proposes a tamper detection technique for semi-fragile watermarking using Quantizationbased Discrete Cosine Transform(DCT)for tamper localization.In this study,the proposed embedding strategy is investigated by experimental tests over the diagonal order of the DCT coefficients.The cover image is divided into non-overlapping blocks of size 8×8 pixels.The DCT is applied to each block,and the coefficients are arranged using a zig-zag pattern within the block.In this study,the low-frequency coefficients are selected to examine the impact of the imperceptibility score and tamper detection accuracy.High accuracy of tamper detection can be achieved by checking the surrounding blocks to determine whether the corresponding block has been tampered with.The proposed tamper detection is tested under various malicious,incidental,and hybrid attacks(both incidental and malicious attacks).The experimental results demonstrate that the proposed technique achieves a Peak-Signal-to-Noise Ratio(PSNR)value of 41.2318 dB,an average Structural Similarity Index Measure(SSIM)value of 0.9768.The proposed scheme is also evaluated against malicious attacks such as copy-move,object deletion,object manipulation,and collage attacks.The proposed scheme can detect the malicious attack localization under various tampering rates.In addition,the proposed scheme can still detect tampered pixels under a hybrid attack,such as a combination ofmalicious and incidental attacks,with an average accuracy of 96.44%.
基金National Key R&D Program of China under Grants 2021YFB2900404the National Natural Science Foundation of China under Grants 62371098。
文摘The acquisition of position information of legitimate users and jammers plays an important role in the emerging non-geostationary synchronous orbit(NGSO)satellite communications.In this paper,we study the multi-signal localization problem in an uplink NGSO satellite communication system.We propose an onboard localization scheme based on multiple observations from the satellite,together with the geometric constraints of the satellite postions,the signal positions,the attitude of the satellite,and the angle-of-arrival(AoAs)of the signals.We develop a massage-passing algorithm,termed the Bayesian blind multi-signal localization(BMSL),to jointly estimate the AoAs and the signal positions.The Cramér-Rao lower bound(CRLB)is derived to characterize the fundamental performance limit of the considered localization problem.Simulation results show that the proposed BMSL algorithm can perform close to the derived CRLB and significantly outperforms its counterpart algorithms.
基金supported in part by the National Natural Science Foundation of China under Grant 52432012in part by the Shanghai Science and Technology Project with 25ZR1402508。
文摘The stator of the maglev track plays a crucial role in the operation of the maglev system.Currently,the efficiency of maglev track inspection is limited by several factors,including the large span of elevated structures,manual visual inspection,short inspection window times,and limited GPS positioning accuracy.To address these issues,this paper proposes a deep learning-based method for detecting and locating stator surface damage.This study establishes a maglev track stator surface image dataset,trains different object detection models,and compares their performance.Ultimately,YOLO and ByteTrack object tracking algorithms were chosen as the basic framework and enhanced to achieve automatic identification of high-speed maglev track stator surface damage images and track and count stator surface localization feature images.By matching the identified damaged images with their corresponding stator segment and beam segment sequence numbers,the location of the damage is pinpointed to the corresponding stator segment,enabling rapid and accurate identification and localization of complex damage to the maglev track stator surface.
基金Project supported by the National Key Research and Decelopment Program of China(Grant No.2021YFB3500302)the National Natural Science Foundation of China(Grant Nos.U22A20116 and 52371200)the Innovation Capability Improvement Project of Hebei Province,China(Grant No.22567605H)。
文摘Large magnetic entropy change(△S_(M))can realize a prominent heat transformation under the magnetic field and directly strengthen the efficacy of the magnetocaloric effect,which provides a pioneering environmentally friendly solidstate strategy to improve refrigeration capacities and efficiencies.The second-order magnetic transition(SOMT)materials have broader△S_(M) peaks without thermal hysteresis,making them highly attractive in magnetic refrigeration,especially in the room temperature range.Here,we report a significant enhancement of△S_(M) at room temperature in single-crystal Mn_(5)Ge_(3).In this SOMT system,we realize a 60%improvement of-△S_(M)^(max) from 3.5 J/kg·K to 5.6 J/kg·K at T=300 K.This considerable enhancement of△S_(M) is achieved by intentionally introducing strain energy through high-pressure constrained deformation.Both experimental results and Monte Carlo simulations demonstrate that the enhancement of△S_(M) originates from the microscopic strain and lattice deformation induced by strain energy after deformation.This strain energy will reconstruct the energy landscape of this ferromagnetic system and enhance magnetization,resulting in a giant intensity of magnetocaloric responses.Our findings provide an approach to increase magnetic entropy change and may give fresh ideas for exploring advanced magnetocaloric materials.
基金support from the National Natural Science Foundation of China(Grant No.42407256)the State Key Laboratory of Hydraulics and Mountain River Engineering,China(Grant No.SKHL2113)the Sichuan Science and Technology Program(Grant No.2024YFHZ0341).
文摘This paper develops a semi-analytical solution for pile penetration in natural soft clays using the strain path method(SPM).The stress-strain behavior of soils is characterized by the S-CLAY1S model,which can capture the anisotropic evolution and destructuring nature of soft clays.By integrating the S-CLAY1S model into the theoretical framework of the SPM,a set of ordinary differential equations is formulated with respect to the vertical coordinate of soil particles.The distribution of excess pore water pressure(EPWP)following pile installation is approximated through one-dimensional(1D)radial integration around the pile shaft.The distribution of stresses and EPWP,along with the evolution of fabric anisotropy within the soil surrounding the pile,is presented to illustrate the response of pile penetration in natural soft clays.The proposed solution is validated against existing theoretical solutions using the SPM and cavity expansion method(CEM),along with experimental data.The findings demonstrate that the SPM reveals lower radial effective stresses and EPWP at the pile shaft than that of CEM.Pile penetration alters the soil's anisotropic properties,inducing rotational hardening and affecting post-installation stress distribution.Soil destructuration eliminates bonding among particles near the pile,resulting in a complete disruption of soil structure at the pile surface,which is particularly pronounced for higher initial soil structure ratios.Minimal variation was observed in the three principal stresses and shear stress on the cone side surface as the angle increased from 18°to 60°,except for a slight reduction in EPWP.
基金financial support provided by the National Natural Science Foundation of China(Grant No.12302472)the Science and Technology Support Program of Jiangsu Province(Grant No.BK20230874)+2 种基金the Aeronautical Science Fund(ASF)(Grant No.2023Z057052005)the Research Fund of State Key Laboratory of Mechanics and Control for Aerospace Structures(Nanjing University of Aeronautics and Astronautics)(Grant No.MCAS-I-0124G02)the funding received from Jiangsu Hanvo Safety Product Co.,Ltd。
文摘High-performance fiber fabrics and composites experienced transverse compression deformation at ultrahigh strain rates near the impact point when subjected to high-velocity impacts,which significantly affected their ballistic limits.In this paper,a fiber-scale experimental method for characterizing ultrahigh strain-rate transverse compression behavior was proposed.To begin with,in order to measure the extremely low stress and strain in small specimens,the conventional Hopkinson bar was reduced to the hundred-micron scale,thereby achieving wave impedance matching with single fibers.In addition,tangential and normal laser Doppler velocimetry(LDV)methods were employed to realize non-contact,high-precision,and high-speed axial velocity measurements of micron-scale incident and transmission bars,respectively.Meanwhile,a microscopic observation system was used to facilitate the installation of miniature fiber samples.The experimental setup and procedures were introduced,and the system accuracy was verified through sample-free loading tests based on one-dimensional stress wave propagation theory.Dynamic compression experiments on Graphene-UHMWPE fibers were carried out,followed by post-compression microstructural characterization via scanning electron microscopy(SEM).Results demonstrated that successful mechanical characterization was achieved at strain rates exceeding 105,an order of magnitude higher than the previously reported maximum rates.Furthermore,during the loading process,the fibers underwent uniform compression deformation while exhibiting pronounced strain-rate effects.This method offers a novel approach for dynamic mechanical characterization of microscale single fibers,enabling the development of comprehensive strain-ratedependent material models to guide the design of advanced composites and high-performance fibers.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11505003 and 52325103)the Anhui Provincial Natural Science Foundation(Grant No.2108085MA25)。
文摘High-performance intelligent protective materials are vital for nuclear energy systems exposed to extreme irradiation.Among them,tungsten-based alloys demonstrate exceptional potential owing to their superior irradiation resistance.Recent experimental studies have demonstrated that W-Ta-Cr-V alloys exhibit excellent irradiation resistance under helium(He)ion irradiation.However,the underlying mechanisms,especially the migration behavior of He atoms,remain unclear.In this work,the influences of uniaxial tensile and compressive strain on He migration in W-Ta-Cr-V complex alloys have been systematically studied through first-principles calculations.Our results demonstrate that He atoms preferentially occupy the tetrahedral interstitial sites,with interstitial formation energies significantly reduced compared to pure W.The introduction of Ta,Cr,and V alloying elements markedly increases the He migration barriers,effectively suppressing He diffusion.Compressive strain increases the migration barriers,inhibiting He bubbles nucleation and growth,while tensile strain decreases the barriers,facilitating bubble formation.Compared to pure W,the W-Ta-Cr-V alloys exhibit both lower He interstitial formation energies and higher migration barriers,with further enhancement under compressive strain.Specifically,compressive strain of 6%increases the He migration barrier of the W-Ta-Cr-V alloy by 0.166 e V,which further widens the difference relative to pure W.These findings provide a theoretical explanation for the superior irradiation resistance of tungsten-based alloys observed experimentally and promote the understanding of irradiation damage in these alloys under strain.
基金financial support from NSF ExpandQISE program.The synthesis of tellurene was supported by NSF under grant no.CMMI-2046936supports from Purdue Research Foundation.
文摘Tellurene,a chiral chain semiconductor with a narrow bandgap and exceptional strain sensitivity,emerges as a pivotal material for tailoring electronic and optoelectronic properties via strain engineering.This study elucidates the fundamental mechanisms of ultrafast laser shock imprinting(LSI)in two-dimensional tellurium(Te),establishing a direct relationship between strain field orientation,mold topology,and anisotropic structural evolution.This is the first demonstration of ultrafast LSI on chiral chain Te unveiling orientation-sensitive dislocation networks.By applying controlled strain fields parallel or transverse to Te’s helical chains,we uncover two distinct deformation regimes.Strain aligned parallel to the chain’s direction induces gliding and rotation governed by weak interchain interactions,preserving covalent intrachain bonds and vibrational modes.In contrast,transverse strain drives shear-mediated multimodal deformations—tensile stretching,compression,and bending—resulting in significant lattice distortions and electronic property modulation.We discovered the critical role of mold topology on deformation:sharp-edged gratings generate localized shear forces surpassing those from homogeneous strain fields via smooth CD molds,triggering dislocation tangle formation,lattice reorientation,and inhomogeneous plastic deformation.Asymmetrical strain configurations enable localized structural transformations while retaining single-crystal integrity in adjacent regions—a balance essential for functional device integration.These insights position LSI as a precision tool for nanoscale strain engineering,capable of sculpting 2D material morphologies without compromising crystallinity.By bridging ultrafast mechanics with chiral chain material science,this work advances the design of strain-tunable devices for next-generation electronics and optoelectronics,while establishing a universal framework for manipulating anisotropic 2D systems under extreme strain rates.This work discovered crystallographic orientation-dependent deformation mechanisms in 2D Te,linking parallel strain to chain gliding and transverse strain to shear-driven multimodal distortion.It demonstrates mold geometry as a critical lever for strain localization and dislocation dynamics,with sharp-edged gratings enabling unprecedented control over lattice reorientation.Crucially,the identification of strain field conditions that reconcile severe plastic deformation with single-crystal retention offers a pathway to functional nanostructure fabrication,redefining LSI’s potential in ultrafast strain engineering of chiral chain materials.
基金Supported by the National Natural Science Foundation of China under Grant No.51975138the High-Tech Ship Scientific Research Project from the Ministry of Industry and Information Technology under Grant No.CJ05N20the National Defense Basic Research Project under Grant No.JCKY2023604C006.
文摘Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.
基金supported by the National Key Research and Development Program of China(2023YFD2100104)Henan Provincial Major Science and Technology Special Fund(231100110400).
文摘Microorganisms are crucial for the breakdown of proteins and lipids in dry-fermented sausages and are intimately associated with the flavor profile of sausages.In this study,we used a mixed starter culture to ferment sausages and investigated the flavor turnover.During the fermentation of salami,the data from free amino acids(FAAs),free fatty acids(FFAs)and volatile flavor substances were used to assess the quality of salami.At the end of fermentation,the total FAAs increased from 1171.32 to 4582.48 mg/kg in the control group and 5053.25 mg/kg in the experimental group.Additionally,following inoculation with the mixed starter culture,the levels of glutamic acid,lysine,methionine,valine and leucine were significantly higher(P<0.05)than those in the control group.Oleic acid(C_(18:1))and chondritic acid(C_(16:0))were the two most abundant FFAs in both salami samples with 45.86%and 26.07%on the 23^(th)day in mixed culture inoculated salami.The mixed starter inoculated group had significantly lower saturated fatty acids and higher percentage levels of monounsaturated fatty acids than the control group(P<0.05).In the volatile flavor substance analysis,a total of 61 volatile compounds were found.Ester compounds were progressively enriched with drying time,significantly increasing the flavor substances,like ethyl diphosgene,1-octen-3-ol,and 2,3-butanediol at P<0.05.The correlation analysis between the core flora and volatile flavor compounds during fermentation and maturation of salami indicates Lactobacillus sakei and Lactobacillus rhamnosus were significantly higher and positively correlated with the major volatile organic compounds,which are the key core microorganisms affecting the flavor quality of fermented sausages.
基金supported in part by the Fundamental Research Funds for the Central Universities under Grant 2242022k60004in part by the National Natural Science Foundation of China(NSFC)under Grants 62261160576,624B2036,W2421087,62422105+1 种基金in part by the Young Elite Scientists Sponsorship Program by CAST 2022QNRC001,and the“Zhishan”Scholars Programs of Southeast Universityin part by the Key Technologies R&D Program of Jiangsu(Prospective and Key Technologies for Industry)under Grants BE2023022,BE2023022-1 and BE2023022-2.
文摘Reconfigurable intelligent surfaces(RISs)not only assist communication but also help the localization of user equipment(UE).This study focuses on indoor localization of UE with a single access point(AP)and multiple RISs.First,we propose a two-stage channel estimation scheme where RIS phase shifts are tuned to obtain multiple channel soundings.In the first stage,the newtonized orthogonal matching pursuit algorithm extracts the parameters of multiple paths from the received signals.Then,the LOS path and RISreflected paths are identified.In the second stage,the estimated path gains of RIS-reflected paths with different phase shifts are utilized to determine the angle of arrival(AOA)at the RIS by obtaining the angular pseudo spectrum.Consequently,by taking the AP and RISs as reference points,the linear least squares estimator can locate UE with the estimated AOAs.Simulation results show that the proposed algorithm can realize centimeter-level localization accuracy in the discussed scenarios.Moreover,the higher accuracy of pseudo spectrum,a larger number of channel soundings,and a larger number of reference points can realize higher localization accuracy of UE.
