Sensitivity analysis and topology optimization of microstructures using strain energy-based method is presented. Compared with homogenization method, the strain energy-based method has advantages of higher computing e...Sensitivity analysis and topology optimization of microstructures using strain energy-based method is presented. Compared with homogenization method, the strain energy-based method has advantages of higher computing efficiency and simplified programming. Both the dual convex programming method and perimeter constraint scheme are used to optimize the 2D and 3D microstructures. Numerical results indicate that the strain energy-based method has the same effectiveness as that of homogenization method for orthotropic materials.展开更多
An alternative strain energy method is proposed for the prediction of effective elastic properties of orthotropic materials in this paper. The method is implemented in the topology optimization procedure to design cel...An alternative strain energy method is proposed for the prediction of effective elastic properties of orthotropic materials in this paper. The method is implemented in the topology optimization procedure to design cellular solids. A comparative study is made between the strain energy method and the well-known homogenization method. Numerical results show that both methods agree well in the numerical prediction and sensitivity analysis of effective elastic tensor when homogeneous boundary conditions are properly specified. Two dimensional and three dimensional microstructures are optimized for maximum stiffness designs by combining the proposed method with the dual optimization algorithm of convex programming. Satisfactory results are obtained for a variety of design cases.展开更多
This paper presents a finite element framework for imposing frictional contact conditions on embedded fracture faces,implemented by the constant-strain assumed enhanced strain(AES)method,where penalty method is used t...This paper presents a finite element framework for imposing frictional contact conditions on embedded fracture faces,implemented by the constant-strain assumed enhanced strain(AES)method,where penalty method is used to impose both non-penetration constraint and Coulomb’s law of friction.The proposed constant-strain AES method for modeling embedded frictional contact can be cast into an integration algorithm similar to those used in the classical plasticity theory,where displacement jump is calculated from the local traction equilibrium at Gauss point,so the method does not introduce any additional global degrees of freedom.Moreover,constant-strain elements are often desirable in practice because they can be easily created automatically for large-scale engineering applications with complicated geometries.As encountered in other enriched finite element methods for frictional contact,the problem of normal contact pressure oscillations is also observed in the constant-strain AES method.Therefore,we developed a strain-smoothing procedure to effectively mitigate the oscillations.We investigated and verified the proposed AES framework through several numerical examples,and illustrated the capability of this method in solving challenging nonlinear frictional contact problems.展开更多
Welding is commonly employed to connect large-scale components in practical engineering.Predicting the resulting deforma-tion and residual stresses during the welding process is typically essential.The thermal-elastic...Welding is commonly employed to connect large-scale components in practical engineering.Predicting the resulting deforma-tion and residual stresses during the welding process is typically essential.The thermal-elastic-plastic method simulates the welding process by examining heat distribution and elastic-plastic stresses.Despite its high computational accuracy,this method is often time-consuming,rendering it less suitable for large component welding predictions.In contrast,the inherent strain method skips the welding process and fo-cuses on the inherent strain in the weld and joint areas post-welding.This method is fast and convenient,particularly suitable for the analysis of large and complex structures.The results show that the error rate is 4.6%when using the inherent strain method to calculate the welding deformation of the test plate.In the calculation of welded parts,the error rate is 5%,which is within the tolerance of the actual engineering.In this paper,the simulation accuracy of the deformation results of the inherent strain method is validated by simulating fusion vacuum ves-sel mockup,aiming to reduce the cost of welding analysis by using this method and to provide reference for practical welding applications.展开更多
Through a modified inherent strain model based on the minimum residual stress and deformation,three building schemes with different building postures and support structures were evaluated by finite element analysis.Re...Through a modified inherent strain model based on the minimum residual stress and deformation,three building schemes with different building postures and support structures were evaluated by finite element analysis.Results demonstrate that according to the principle of reducing the overall height of the building and reducing the support structure with a large tilt angle from the building direction,the residual stress and deformation can be effectively reduced by proper design of building posture and support before laser powder bed melting.Moreover,without the data of thermophysical property variation of Ti-6Al-4V artificial knee implants with temperature,predicting the residual stress and deformation with acceptable accuracy and reduced time cost can be achieved by the inherent strain model.展开更多
Soft self-healing materials are promising candidates for flexible electronic devices due to their excep-tional compatibility,extensibility,and self-restorability.Generally,these materials suffer from low tensile stren...Soft self-healing materials are promising candidates for flexible electronic devices due to their excep-tional compatibility,extensibility,and self-restorability.Generally,these materials suffer from low tensile strength and susceptibility to fracture because of the restricted microstructure design.Herein,we pro-pose a hydrothermal-freeze-thaw method to construct high-strength self-healing hydrogels with even in-terconnected networks and distinctive wrinkled surfaces.The integration of the wrinkled outer surface with the three-dimensional internal network confers the self-healing hydrogel with enhanced mechan-ical strength.This hydrogel achieves a tensile strength of 223 kPa,a breaking elongation of 442%,an adhesion strength of 57.6 kPa,and an adhesion energy of 237.2 J m-2.Meanwhile,the hydrogel demon-strates impressive self-repair capability(repair efficiency:93%).Moreover,the density functional theory(DFT)calculations are used to substantiate the stable existence of hydrogen bonding between the PPPBG hydrogel and water molecules which ensures the durability of the PPPBG hydrogel for long-term applica-tion.The measurements demonstrate that this multifunctional hydrogel possesses the requisite sensitivity and durability to serve as a strain sensor,which monitors a spectrum of motion signals including subtle vocalizations,pronounced facial expressions,and limb articulations.This work presents a viable strategy for healthcare monitoring,soft robotics,and interactive electronic skins.展开更多
Dear Editor,Influenza viruses cause significant mortality and morbidity in humans.Vaccination is currently the most effective way to combat the virus(Perofsky and Nelson,2020).Unfortunately,the influenza virus frequen...Dear Editor,Influenza viruses cause significant mortality and morbidity in humans.Vaccination is currently the most effective way to combat the virus(Perofsky and Nelson,2020).Unfortunately,the influenza virus frequently changes its antigenicity through rapid mutations,leading to decreased vaccine efficacy or even failure.To improve vaccine effectiveness,it is necessary to monitor antigenic variation and update vaccine strains when significant antigenic variation occurs(Perofsky and Nelson,2020;Malik et al.,2024).展开更多
The valence subband energies and wave functions of a tensile strained quantum well are calculated by the plane wave expansion method within the 6×6 Luttinger Kohn model.The effect of the number and period of pla...The valence subband energies and wave functions of a tensile strained quantum well are calculated by the plane wave expansion method within the 6×6 Luttinger Kohn model.The effect of the number and period of plane waves used for expansion on the stability of energy eigenvalues is examined.For practical calculation,it should choose the period large sufficiently to ensure the envelope functions vanish at the boundary and the number of plane waves large enough to ensure the energy eigenvalues keep unchanged within a prescribed range.展开更多
A thorough understanding of the texture evolution of near-αtitanium alloys during the hot metal forming can help obtain an optimal crystallographic texture and material performance.The strain state has an obvious eff...A thorough understanding of the texture evolution of near-αtitanium alloys during the hot metal forming can help obtain an optimal crystallographic texture and material performance.The strain state has an obvious effect on the texture evolution of near-αtitanium alloys during the hot metal forming.In this paper,the texture evolution of a near-αTA15 titanium alloy during the hot metal forming under different strain states were discussed based on the crystal plasticity finite element method.It is found that the basal and prismatic slip systems are regarded as the dominant slip modes due to the similar low critical resolved shear stress during the hot metal forming of the TA15 sheet rotating the lattice around the[1010]and 0001 axis,respectively.Once both of them cannot be activated,the pyramidal-2 slipping occurs rotating the lattice around the[1010]axis.The relationship between the texture evolution and strain state is established.All the(0001)orientations form a band perpendicular to the direction of the first principal strain.The width of the band along the direction of the second principal strain depends on the ratio of the compressive effect to the tensile effect of the second principal strain.This relationship can help control the crystallographic texture and mechanical properties of the titanium alloys component during the hot metal forming.展开更多
In recent years, the method of magnetic survey as one of the new techniques in geological and geophysical studies is known. In this study to determine the shape of the stress field of the two methods, Anisotropy of Ma...In recent years, the method of magnetic survey as one of the new techniques in geological and geophysical studies is known. In this study to determine the shape of the stress field of the two methods, Anisotropy of Magnetic Susceptibility (AMS) and paleostress?have been used. Paleomagnetism is the characteristics of magnetic rocks. Some issues in associated with the past places of continental and oceanic plates can be solved. AMS is one of the paleomagnetism methods that pay to measurement of parameters (which are reflector of the magnetic fabrics rocks). It is presenting an ellipsoid with three-axis perpendicular to each other that defines magnetic ellipsoid. In this regard, the number of 12 stations in different rocks (Jurassic to Quaternary) in the southern region of Ardebil sampling was conducted. In this connection, the study of magnetic fabrics has shown an elliptical magnetic susceptibility with the prolate shape. For the separation of paleostress phases in the Khalkhal area using the analysis of the paleostress based on the study of heterogeneous fault-slip data and sliding lineaments. Firstly, data were picked from 10 stations, and after their analysis, the elliptical shape (prolate) has been determinated. The shape of the ellipsoid, based on AMS and paleostress methods and their results show that in both methods the shape of the stress field is prolate.展开更多
Structural strain modes are able to detect changes in local structural performance, but errors are inevitably intermixed in the measured data. In this paper, strain modal parameters are considered as random variables,...Structural strain modes are able to detect changes in local structural performance, but errors are inevitably intermixed in the measured data. In this paper, strain modal parameters are considered as random variables, and their uncertainty is analyzed by a Bayesian method based on the structural frequency response function （FRF）. The estimates of strain modal parameters with maximal posterior probability are determined. Several independent measurements of the FRF of a four-story reinforced concrete flame structural model were performed in the laboratory. The ability to identify the stiffness change in a concrete column using the strain mode was verified. It is shown that the uncertainty of the natural frequency is very small. Compared with the displacement mode shape, the variations of strain mode shapes at each point are quite different. The damping ratios are more affected by the types of test systems. Except for the case where a high order strain mode does not identify local damage, the first order strain mode can provide an exact indication of the damage location.展开更多
Due to the current trend towards lightweight design in automotive industry,hollow stepped gear shafts for automobile and its radial forging process are widely investigated.Utilizing coupled finite element thermo-mecha...Due to the current trend towards lightweight design in automotive industry,hollow stepped gear shafts for automobile and its radial forging process are widely investigated.Utilizing coupled finite element thermo-mechanical model,radial forging process of a hollow stepped gear shaft for automobile was simulated.The optimal combination of three process parameters including initial temperature,rotation rate and radial reduction was also selected using orthogonal design method.To examine the strain inhomogeneity of the forging workpiece,the strain inhomogeneity factor was introduced.The results reveal that the maximum effective strain and the minimum effective strain appeared in the outermost and innermost zones of different cross sections for the hollow stepped gear shaft,respectively.Optimal forging parameters are determined as a combination of initial temperature of 780°C,rotation rate of 21°/stroke and radial reduction of 3 mm.展开更多
The fatigue lives of materials and structures at different strain levels show het- eroscedasticity. In addition when the number of test specimens is insufficient, the fatigue strength coefficient and fatigue ductility...The fatigue lives of materials and structures at different strain levels show het- eroscedasticity. In addition when the number of test specimens is insufficient, the fatigue strength coefficient and fatigue ductility coefficient of the fitting parameters in the total strain life equa- tion may not have definite physical significance. In this work, a maximum likelihood method for estimating probabilistic strain amplitude fatigue life curves is presented based on the fatigue lives at different strain levels. The proposed method is based on the general basic assumption that the logarithm of fatigue life at an arbitrary strain level is normally distributed. The rela- tionship among the parameters of total strain life equation, monotonic ultimate tensile stress and percentage reduction of area is adopted. The presented approach is finally illustrated by two applications. It is shown that probabilistic strain amplitude-fatigue life curves can be eas- ily estimated based on the maximum likelihood method. The results show that fatigue lives at different strain levels have heteroscedasticity and the values of fatigue strength coefficient and fatigue ductility coefficient obtained by the proposed method are close to those of the true tensile fracture stress and true tensile fracture strain.展开更多
This paper proposes a novel nonlinear energy-based coupling control for an underactuated offshore ship-mounted crane,which guarantees both precise trolley positioning and payload swing suppressing performances under e...This paper proposes a novel nonlinear energy-based coupling control for an underactuated offshore ship-mounted crane,which guarantees both precise trolley positioning and payload swing suppressing performances under external sea wave disturbance. In addition to having such typical nonlinear underactuated property, as it is well known, an offshore ship-mounted crane also suffers from much unexpected persistent disturbances induced by sea waves or currents, which, essentially different from an overhead crane fixed on land, cause much difficulty in modeling and controller design. Inspired by the desire to achieve appropriate control performance against those challenging factors, in this paper, through carefully analyzing the inherent mechanism of the nonlinear dynamics, we first construct a new composite signal to enhance the coupling behavior of the trolley motion as well as the payload swing in the presence of ship′s roll motion disturbance. Based on which, an energy-based coupling control law is presented to achieve asymptotic stability of the crane control system′s equilibrium point. Without any linearization of the complex nonlinear dynamics, unlike traditional feedback controllers, the proposed control law takes a much simpler structure independent of the system parameters. To support the theoretical derivations and to further verify the actual control performance, Lyapunov-based mathematical analysis as well as numerical simulation/experimental results are carried out, which clarify the feasibility and superior performance of the proposed method over complicated disturbances.展开更多
Optical full-field measurement methods are now widely applied in various domains. In general,the displacement fields can be directly obtained from the measurement,however in mechanical analysis strain fields are prefe...Optical full-field measurement methods are now widely applied in various domains. In general,the displacement fields can be directly obtained from the measurement,however in mechanical analysis strain fields are preferred.To extract strain fields from noisy displacement fields is always a challenging topic.In this study,a finite element method for smoothing displacement fields and calculating strain fields is proposed.An experimental test case on a holed aluminum specimen under tension is applied to validate this method.The heterogeneous displacement fields are measured by digital image correlation(DIC).By this proposed method,the result shows that the measuring noise on experimental displacement fields can be successfully removed,and strain fields can be reconstructed in the arbitrary area.展开更多
The isotropic and anisotropic behaviors are considered as the important formats of the constitutive behaviors,and can also be called the global properties.To improve the identification ability of virtual fields method...The isotropic and anisotropic behaviors are considered as the important formats of the constitutive behaviors,and can also be called the global properties.To improve the identification ability of virtual fields method(VFM)when the global properties are unknown,this paper proposes the strain correlation method(SCM)to determine the global properties before the parameter identification using the VFM.Firstly,the basic principle of SCM is described in detail.Then,the feasibility and accuracy of SCM are verified through the numerical experiments based on the three-point bending configuration and the real experiment of polymethyl methacrylate(PMMA).The influence of the additive Gaussian white noise,local errors in the strain fields,and missing data at the specimen edges on the characterization results are evaluated.The results show that the SCM has good noise immunity and lower accuracy requirements for the strain fields.As an application,the mechanical properties of Ti-6A1-4V alloys fabricated by selective laser melting(SLM)are characterized by the SCM.The results show that the alloys are isotropic,and the isotropic VFM is utilized to determine the mechanical parameters.By using the SCM,the accuracy of identification results can be improved for the isotropic or bidirectional reinforced orthotropic materials when using VFM.展开更多
C^1 natural element method （C^1 NEM） is applied to strain gradient linear elasticity, and size effects on mi crostructures are analyzed. The shape functions in C^1 NEM are built upon the natural neighbor interpolati...C^1 natural element method （C^1 NEM） is applied to strain gradient linear elasticity, and size effects on mi crostructures are analyzed. The shape functions in C^1 NEM are built upon the natural neighbor interpolation （NNI）, with interpolation realized to nodal function and nodal gradient values, so that the essential boundary conditions （EBCs） can be imposed directly in a Galerkin scheme for partial differential equations （PDEs）. In the present paper, C^1 NEM for strain gradient linear elasticity is constructed, and sev- eral typical examples which have analytical solutions are presented to illustrate the effectiveness of the constructed method. In its application to microstructures, the size effects of bending stiffness and stress concentration factor （SCF） are studied for microspeciem and microgripper, respectively. It is observed that the size effects become rather strong when the width of spring for microgripper, the radius of circular perforation and the long axis of elliptical perforation for microspeciem come close to the material characteristic length scales. For the U-shaped notch, the size effects decline obviously with increasing notch radius, and decline mildly with increasing length of notch.展开更多
In order to establish the quantitative relationship between equivalent strain and the performance index of the deformed material within the range of certain passes for equal channel angular processing （ECAP）, a new ...In order to establish the quantitative relationship between equivalent strain and the performance index of the deformed material within the range of certain passes for equal channel angular processing （ECAP）, a new approach to characterize the equivalent strain was proposed. The results show that there exists better accordance between mechanical property （such as hardness or strength） and equivalent strain after rolling and ECAP in a certain range of deformation amount, and Gauss equation can be satisfied among the equivalent strain and the mechanical properties for ECAP. Through regression analysis on the data of hardness and strength after the deformation, a more generalized expression of equivalent strain for ECAP is proposed as：ε=k0exp[-（k1M-k2）^2], where M is the strength or hardness of the material, k1 is the modified coefficient （k1∈ （0, 1））, ko and k2 are two parameters dependent on the critical strain and mechanical property that reaches saturation state for the material, respectively. In this expression the equivalent strain for ECAP is characterized novelly through the mechanical parameter relating to material property rather than the classical geometry equation.展开更多
基金National Natural Science Foundation of China （90405016, 10676028） 973 Program （2006CB601205）+1 种基金 863 Project （2006AA04Z 122） Aeronautical Science Foundation （04B53080, 2006ZA 53006） and 111 Project （B07050）
文摘Sensitivity analysis and topology optimization of microstructures using strain energy-based method is presented. Compared with homogenization method, the strain energy-based method has advantages of higher computing efficiency and simplified programming. Both the dual convex programming method and perimeter constraint scheme are used to optimize the 2D and 3D microstructures. Numerical results indicate that the strain energy-based method has the same effectiveness as that of homogenization method for orthotropic materials.
基金The project supported by the National Natural Science Foundation of China(10372083,90405016)973 Program(2006CB601205)the Aeronautical Science Foundation(04B53080)
文摘An alternative strain energy method is proposed for the prediction of effective elastic properties of orthotropic materials in this paper. The method is implemented in the topology optimization procedure to design cellular solids. A comparative study is made between the strain energy method and the well-known homogenization method. Numerical results show that both methods agree well in the numerical prediction and sensitivity analysis of effective elastic tensor when homogeneous boundary conditions are properly specified. Two dimensional and three dimensional microstructures are optimized for maximum stiffness designs by combining the proposed method with the dual optimization algorithm of convex programming. Satisfactory results are obtained for a variety of design cases.
基金supported by the Fundamental Research Funds for the Central Universities (Grant No.2021FZZX001-14)and ZJU-ZCCC Institute of Collaborative Innovation (Grant No.ZDJG2021005).
文摘This paper presents a finite element framework for imposing frictional contact conditions on embedded fracture faces,implemented by the constant-strain assumed enhanced strain(AES)method,where penalty method is used to impose both non-penetration constraint and Coulomb’s law of friction.The proposed constant-strain AES method for modeling embedded frictional contact can be cast into an integration algorithm similar to those used in the classical plasticity theory,where displacement jump is calculated from the local traction equilibrium at Gauss point,so the method does not introduce any additional global degrees of freedom.Moreover,constant-strain elements are often desirable in practice because they can be easily created automatically for large-scale engineering applications with complicated geometries.As encountered in other enriched finite element methods for frictional contact,the problem of normal contact pressure oscillations is also observed in the constant-strain AES method.Therefore,we developed a strain-smoothing procedure to effectively mitigate the oscillations.We investigated and verified the proposed AES framework through several numerical examples,and illustrated the capability of this method in solving challenging nonlinear frictional contact problems.
基金supported by the National Key Scientific and Technological Infrastructure Construction Project(No.2018-000052-73-01-001228)National Natural Science Foundation of China Young Scientists Fund Project(12105185)Science Foundation of Institute of Plasma Physics,Chinese Academy of Sciences(No.DSJJ-2023-06).
文摘Welding is commonly employed to connect large-scale components in practical engineering.Predicting the resulting deforma-tion and residual stresses during the welding process is typically essential.The thermal-elastic-plastic method simulates the welding process by examining heat distribution and elastic-plastic stresses.Despite its high computational accuracy,this method is often time-consuming,rendering it less suitable for large component welding predictions.In contrast,the inherent strain method skips the welding process and fo-cuses on the inherent strain in the weld and joint areas post-welding.This method is fast and convenient,particularly suitable for the analysis of large and complex structures.The results show that the error rate is 4.6%when using the inherent strain method to calculate the welding deformation of the test plate.In the calculation of welded parts,the error rate is 5%,which is within the tolerance of the actual engineering.In this paper,the simulation accuracy of the deformation results of the inherent strain method is validated by simulating fusion vacuum ves-sel mockup,aiming to reduce the cost of welding analysis by using this method and to provide reference for practical welding applications.
基金Natural Science Foundation of Shandong Province(ZR2020ME020)。
文摘Through a modified inherent strain model based on the minimum residual stress and deformation,three building schemes with different building postures and support structures were evaluated by finite element analysis.Results demonstrate that according to the principle of reducing the overall height of the building and reducing the support structure with a large tilt angle from the building direction,the residual stress and deformation can be effectively reduced by proper design of building posture and support before laser powder bed melting.Moreover,without the data of thermophysical property variation of Ti-6Al-4V artificial knee implants with temperature,predicting the residual stress and deformation with acceptable accuracy and reduced time cost can be achieved by the inherent strain model.
基金supported by the National Natural Science Foundation of China(Nos.U21A6004,U21A20172,61804091,21574076,and U1510121)the Science and Technology Major Project of Shanxi(No.202101030201022)+1 种基金the Fundamental Research Program of Shanxi Province(No.202103021223019)the Open Fund of the Key Lab of Organic Optoelectronics&Molecular Engineering.
文摘Soft self-healing materials are promising candidates for flexible electronic devices due to their excep-tional compatibility,extensibility,and self-restorability.Generally,these materials suffer from low tensile strength and susceptibility to fracture because of the restricted microstructure design.Herein,we pro-pose a hydrothermal-freeze-thaw method to construct high-strength self-healing hydrogels with even in-terconnected networks and distinctive wrinkled surfaces.The integration of the wrinkled outer surface with the three-dimensional internal network confers the self-healing hydrogel with enhanced mechan-ical strength.This hydrogel achieves a tensile strength of 223 kPa,a breaking elongation of 442%,an adhesion strength of 57.6 kPa,and an adhesion energy of 237.2 J m-2.Meanwhile,the hydrogel demon-strates impressive self-repair capability(repair efficiency:93%).Moreover,the density functional theory(DFT)calculations are used to substantiate the stable existence of hydrogen bonding between the PPPBG hydrogel and water molecules which ensures the durability of the PPPBG hydrogel for long-term applica-tion.The measurements demonstrate that this multifunctional hydrogel possesses the requisite sensitivity and durability to serve as a strain sensor,which monitors a spectrum of motion signals including subtle vocalizations,pronounced facial expressions,and limb articulations.This work presents a viable strategy for healthcare monitoring,soft robotics,and interactive electronic skins.
基金upported by the Major Project of Guangzhou National Laboratory(GZNL2024A01002)National Key Plan for Scientific Research and Development of China(2022YFC2303802)+1 种基金National Natural Science Foundation of China(32170651&32370700)Hunan Provincial Natural Science Foundation of China(2024JJ2015).
文摘Dear Editor,Influenza viruses cause significant mortality and morbidity in humans.Vaccination is currently the most effective way to combat the virus(Perofsky and Nelson,2020).Unfortunately,the influenza virus frequently changes its antigenicity through rapid mutations,leading to decreased vaccine efficacy or even failure.To improve vaccine effectiveness,it is necessary to monitor antigenic variation and update vaccine strains when significant antigenic variation occurs(Perofsky and Nelson,2020;Malik et al.,2024).
文摘The valence subband energies and wave functions of a tensile strained quantum well are calculated by the plane wave expansion method within the 6×6 Luttinger Kohn model.The effect of the number and period of plane waves used for expansion on the stability of energy eigenvalues is examined.For practical calculation,it should choose the period large sufficiently to ensure the envelope functions vanish at the boundary and the number of plane waves large enough to ensure the energy eigenvalues keep unchanged within a prescribed range.
基金financially supported by the National Natural Science Foundation of China(No.51401065).
文摘A thorough understanding of the texture evolution of near-αtitanium alloys during the hot metal forming can help obtain an optimal crystallographic texture and material performance.The strain state has an obvious effect on the texture evolution of near-αtitanium alloys during the hot metal forming.In this paper,the texture evolution of a near-αTA15 titanium alloy during the hot metal forming under different strain states were discussed based on the crystal plasticity finite element method.It is found that the basal and prismatic slip systems are regarded as the dominant slip modes due to the similar low critical resolved shear stress during the hot metal forming of the TA15 sheet rotating the lattice around the[1010]and 0001 axis,respectively.Once both of them cannot be activated,the pyramidal-2 slipping occurs rotating the lattice around the[1010]axis.The relationship between the texture evolution and strain state is established.All the(0001)orientations form a band perpendicular to the direction of the first principal strain.The width of the band along the direction of the second principal strain depends on the ratio of the compressive effect to the tensile effect of the second principal strain.This relationship can help control the crystallographic texture and mechanical properties of the titanium alloys component during the hot metal forming.
文摘In recent years, the method of magnetic survey as one of the new techniques in geological and geophysical studies is known. In this study to determine the shape of the stress field of the two methods, Anisotropy of Magnetic Susceptibility (AMS) and paleostress?have been used. Paleomagnetism is the characteristics of magnetic rocks. Some issues in associated with the past places of continental and oceanic plates can be solved. AMS is one of the paleomagnetism methods that pay to measurement of parameters (which are reflector of the magnetic fabrics rocks). It is presenting an ellipsoid with three-axis perpendicular to each other that defines magnetic ellipsoid. In this regard, the number of 12 stations in different rocks (Jurassic to Quaternary) in the southern region of Ardebil sampling was conducted. In this connection, the study of magnetic fabrics has shown an elliptical magnetic susceptibility with the prolate shape. For the separation of paleostress phases in the Khalkhal area using the analysis of the paleostress based on the study of heterogeneous fault-slip data and sliding lineaments. Firstly, data were picked from 10 stations, and after their analysis, the elliptical shape (prolate) has been determinated. The shape of the ellipsoid, based on AMS and paleostress methods and their results show that in both methods the shape of the stress field is prolate.
基金Ministry of Construction of China through the Science and Technique Program Grant No.06-k6-13Guangzhou Construction Technological Development Foundation through Grant No.200409+1 种基金Guangdong Province Natural Science Foundation through Grant No.5300381 Guangzhou Science and Technique Bureau through Science and Technique Program Grant No.2006J1-C0451
文摘Structural strain modes are able to detect changes in local structural performance, but errors are inevitably intermixed in the measured data. In this paper, strain modal parameters are considered as random variables, and their uncertainty is analyzed by a Bayesian method based on the structural frequency response function （FRF）. The estimates of strain modal parameters with maximal posterior probability are determined. Several independent measurements of the FRF of a four-story reinforced concrete flame structural model were performed in the laboratory. The ability to identify the stiffness change in a concrete column using the strain mode was verified. It is shown that the uncertainty of the natural frequency is very small. Compared with the displacement mode shape, the variations of strain mode shapes at each point are quite different. The damping ratios are more affected by the types of test systems. Except for the case where a high order strain mode does not identify local damage, the first order strain mode can provide an exact indication of the damage location.
基金Projects(51774054,51974050)supported by the National Natural Science Foundation of China。
文摘Due to the current trend towards lightweight design in automotive industry,hollow stepped gear shafts for automobile and its radial forging process are widely investigated.Utilizing coupled finite element thermo-mechanical model,radial forging process of a hollow stepped gear shaft for automobile was simulated.The optimal combination of three process parameters including initial temperature,rotation rate and radial reduction was also selected using orthogonal design method.To examine the strain inhomogeneity of the forging workpiece,the strain inhomogeneity factor was introduced.The results reveal that the maximum effective strain and the minimum effective strain appeared in the outermost and innermost zones of different cross sections for the hollow stepped gear shaft,respectively.Optimal forging parameters are determined as a combination of initial temperature of 780°C,rotation rate of 21°/stroke and radial reduction of 3 mm.
基金supported by the National Natural Science Foundation of China(No.51475022)
文摘The fatigue lives of materials and structures at different strain levels show het- eroscedasticity. In addition when the number of test specimens is insufficient, the fatigue strength coefficient and fatigue ductility coefficient of the fitting parameters in the total strain life equa- tion may not have definite physical significance. In this work, a maximum likelihood method for estimating probabilistic strain amplitude fatigue life curves is presented based on the fatigue lives at different strain levels. The proposed method is based on the general basic assumption that the logarithm of fatigue life at an arbitrary strain level is normally distributed. The rela- tionship among the parameters of total strain life equation, monotonic ultimate tensile stress and percentage reduction of area is adopted. The presented approach is finally illustrated by two applications. It is shown that probabilistic strain amplitude-fatigue life curves can be eas- ily estimated based on the maximum likelihood method. The results show that fatigue lives at different strain levels have heteroscedasticity and the values of fatigue strength coefficient and fatigue ductility coefficient obtained by the proposed method are close to those of the true tensile fracture stress and true tensile fracture strain.
基金supported by National Natural Science Foundation of China (No. 11372144)National Science Fund for Distinguished Young Scholars of China (No. 61325017)National Science Foundation of Tianjin
文摘This paper proposes a novel nonlinear energy-based coupling control for an underactuated offshore ship-mounted crane,which guarantees both precise trolley positioning and payload swing suppressing performances under external sea wave disturbance. In addition to having such typical nonlinear underactuated property, as it is well known, an offshore ship-mounted crane also suffers from much unexpected persistent disturbances induced by sea waves or currents, which, essentially different from an overhead crane fixed on land, cause much difficulty in modeling and controller design. Inspired by the desire to achieve appropriate control performance against those challenging factors, in this paper, through carefully analyzing the inherent mechanism of the nonlinear dynamics, we first construct a new composite signal to enhance the coupling behavior of the trolley motion as well as the payload swing in the presence of ship′s roll motion disturbance. Based on which, an energy-based coupling control law is presented to achieve asymptotic stability of the crane control system′s equilibrium point. Without any linearization of the complex nonlinear dynamics, unlike traditional feedback controllers, the proposed control law takes a much simpler structure independent of the system parameters. To support the theoretical derivations and to further verify the actual control performance, Lyapunov-based mathematical analysis as well as numerical simulation/experimental results are carried out, which clarify the feasibility and superior performance of the proposed method over complicated disturbances.
基金supported by the National Basic Research Program of China("973"Project, Grant No.2010CB631005,2011CB606105)the National Natural Science Foundation of China(Grant No.10625209, 10732080,90916010)+2 种基金China Postdoctoral Science Foundation (Grant No.20090460335)Specialized Research Fund for the Doctoral Program of Higher Education(Grant No.20090002110048)the opening funds from the State Key Laboratory of Explosion Science and Technology (KFJJ10-18Y)
文摘Optical full-field measurement methods are now widely applied in various domains. In general,the displacement fields can be directly obtained from the measurement,however in mechanical analysis strain fields are preferred.To extract strain fields from noisy displacement fields is always a challenging topic.In this study,a finite element method for smoothing displacement fields and calculating strain fields is proposed.An experimental test case on a holed aluminum specimen under tension is applied to validate this method.The heterogeneous displacement fields are measured by digital image correlation(DIC).By this proposed method,the result shows that the measuring noise on experimental displacement fields can be successfully removed,and strain fields can be reconstructed in the arbitrary area.
基金This research was financially supported by the National Key Research and Development Program of China(Grant 2017YFB1103900)the National Science and Technology Major Project(Grant 2017-VI-0003-0073)+1 种基金the National Natural Science Foundation of China(Grant 11672153)Hubei Provincial Major Program of Technological Innovation(Grant 2017AAA121).
文摘The isotropic and anisotropic behaviors are considered as the important formats of the constitutive behaviors,and can also be called the global properties.To improve the identification ability of virtual fields method(VFM)when the global properties are unknown,this paper proposes the strain correlation method(SCM)to determine the global properties before the parameter identification using the VFM.Firstly,the basic principle of SCM is described in detail.Then,the feasibility and accuracy of SCM are verified through the numerical experiments based on the three-point bending configuration and the real experiment of polymethyl methacrylate(PMMA).The influence of the additive Gaussian white noise,local errors in the strain fields,and missing data at the specimen edges on the characterization results are evaluated.The results show that the SCM has good noise immunity and lower accuracy requirements for the strain fields.As an application,the mechanical properties of Ti-6A1-4V alloys fabricated by selective laser melting(SLM)are characterized by the SCM.The results show that the alloys are isotropic,and the isotropic VFM is utilized to determine the mechanical parameters.By using the SCM,the accuracy of identification results can be improved for the isotropic or bidirectional reinforced orthotropic materials when using VFM.
基金supported by the SDUST Spring Bud (2009AZZ021)Taian Science and Technology Development (20112001)
文摘C^1 natural element method （C^1 NEM） is applied to strain gradient linear elasticity, and size effects on mi crostructures are analyzed. The shape functions in C^1 NEM are built upon the natural neighbor interpolation （NNI）, with interpolation realized to nodal function and nodal gradient values, so that the essential boundary conditions （EBCs） can be imposed directly in a Galerkin scheme for partial differential equations （PDEs）. In the present paper, C^1 NEM for strain gradient linear elasticity is constructed, and sev- eral typical examples which have analytical solutions are presented to illustrate the effectiveness of the constructed method. In its application to microstructures, the size effects of bending stiffness and stress concentration factor （SCF） are studied for microspeciem and microgripper, respectively. It is observed that the size effects become rather strong when the width of spring for microgripper, the radius of circular perforation and the long axis of elliptical perforation for microspeciem come close to the material characteristic length scales. For the U-shaped notch, the size effects decline obviously with increasing notch radius, and decline mildly with increasing length of notch.
基金Projects(50471102,50671089) supported by the National Natural Science Foundation of China
文摘In order to establish the quantitative relationship between equivalent strain and the performance index of the deformed material within the range of certain passes for equal channel angular processing （ECAP）, a new approach to characterize the equivalent strain was proposed. The results show that there exists better accordance between mechanical property （such as hardness or strength） and equivalent strain after rolling and ECAP in a certain range of deformation amount, and Gauss equation can be satisfied among the equivalent strain and the mechanical properties for ECAP. Through regression analysis on the data of hardness and strength after the deformation, a more generalized expression of equivalent strain for ECAP is proposed as：ε=k0exp[-（k1M-k2）^2], where M is the strength or hardness of the material, k1 is the modified coefficient （k1∈ （0, 1））, ko and k2 are two parameters dependent on the critical strain and mechanical property that reaches saturation state for the material, respectively. In this expression the equivalent strain for ECAP is characterized novelly through the mechanical parameter relating to material property rather than the classical geometry equation.
