Flexible rolling is a forming process based on thickness reduction, and the precision of thickness reduction is the key factor affecting bending deformation. The major purpose of the present work is to solve the probl...Flexible rolling is a forming process based on thickness reduction, and the precision of thickness reduction is the key factor affecting bending deformation. The major purpose of the present work is to solve the problem of bending deformation error caused by insufficient thickness reduction. Under the condition of different rolling reductions with the same sheet thickness and the same thickness reduction with different sheet thicknesses, the thickness reduction error of sheet metal is analyzed. In addition, the bending deformation of sheet metal under the same conditions is discussed and the influence of the multi-step forming process on the thickness reduction error is studied. The results show that, under the condition of the same sheet thickness, the thickness reduction error increases with increasing rolling reduction because of an increase in work hardening. As rolling reduction increases, the longitudinal bending deformation decreases because of the decrease of the maximum thickness difference. Under the condition with the same thickness reduction, the thickness reduction error increases because of the decrease of the rolling force with increasing sheet thickness. As the sheet thickness increases, the longitudinal bending deformation increases because of the increase in the maximum thickness difference. A larger bending deformation is divided into a number of small bending deformations in a multi-step forming process, avoiding a sharp increase in the degree of work hardening; the thickness reduction error is effectively reduced in the multi-step forming process. Numerical simulation results agree with the results of the forming experiments.展开更多
近年来,超宽带(Ultra-wideband,UWB)通信技术因其具有数据传输速率高、功耗低、保密性高、成本低等诸多优点,成为室内高速数据传输的一种有效解决方案。由于高速通信下码间串扰极大地影响了UWB系统的接收性能,需要在解调前采用Rake接收...近年来,超宽带(Ultra-wideband,UWB)通信技术因其具有数据传输速率高、功耗低、保密性高、成本低等诸多优点,成为室内高速数据传输的一种有效解决方案。由于高速通信下码间串扰极大地影响了UWB系统的接收性能,需要在解调前采用Rake接收机和均衡等手段消除码间串扰。针对自适应最小误码率(Adaptive Minimum Bit Error Rate,AMBER)均衡算法与Rake接收机结合进行研究,提出了一种变步长自适应最小误码率(Variable Step-Adaptive Minimum Bit Error Rate,VS-AMBER)均衡算法,在较低信噪比和较高信噪比情况下分别使用不同的变步长方案,较高信噪比下在收敛速度和收敛精度上有所提升,较低信噪比下降低了误码率和功耗。展开更多
摆线泵转子的齿廓形状和加工精度决定了齿轮泵容腔的密封性,进而影响吸油和压油等运动特性。然而,转子的齿廓形状多是企业根据自身实际需求自行设计的,这就造成齿廓误差测量过程中的测量基准和设计基准不一致,测量结果更无法准确反映转...摆线泵转子的齿廓形状和加工精度决定了齿轮泵容腔的密封性,进而影响吸油和压油等运动特性。然而,转子的齿廓形状多是企业根据自身实际需求自行设计的,这就造成齿廓误差测量过程中的测量基准和设计基准不一致,测量结果更无法准确反映转子的齿廓加工质量。鉴于此,将企业设计的产品模型数据交互规范(Standard for the Exchange of Product model data, STEP)齿廓作为测量所必需的基准数据,在使用一维测头的国产齿轮测量中心上完成了转子齿廓的快速检测,采用重构及匹配等补偿处理方法,实现了摆线泵转子误差的精确评定。结果表明,该方法具有较好的柔性,对于复杂齿面的精确测量和评定具有重要的理论意义。展开更多
Errors due to split time stepping are discussed for an explicit free–surface ocean model. In commonly used split time stepping, the way of time integration for the barotropic momentum equation is not compatible with ...Errors due to split time stepping are discussed for an explicit free–surface ocean model. In commonly used split time stepping, the way of time integration for the barotropic momentum equation is not compatible with that of the baroclinic one. The baroclinic equation has three–time–level structure because of leapfrog scheme. The barotropic one, however, has two–time–level structure when represented in terms of the baroclinic time level, on which the baroclinic one is integrated. This incompatibility results in the splitting errors as shown in this paper. The proper split time stepping is therefore proposed in such a way that the compatibility is kept between the barotropic and baroclinic equations. Its splitting errors are shown extremely small, so that it is particularly relevant to long–term integration for climate studies. It is applied to a free–surface model for the North Pacific Ocean.展开更多
For aircraft manufacturing industries, the analyses and prediction of part machining error during machining process are very important to control and improve part machining quality. In order to effectively control mac...For aircraft manufacturing industries, the analyses and prediction of part machining error during machining process are very important to control and improve part machining quality. In order to effectively control machining error, the method of integrating multivariate statistical process control （MSPC） and stream of variations （SoV） is proposed. Firstly, machining error is modeled by multi-operation approaches for part machining process. SoV is adopted to establish the mathematic model of the relationship between the error of upstream operations and the error of downstream operations. Here error sources not only include the influence of upstream operations but also include many of other error sources. The standard model and the predicted model about SoV are built respectively by whether the operation is done or not to satisfy different requests during part machining process. Secondly, the method of one-step ahead forecast error （OSFE） is used to eliminate autocorrelativity of the sample data from the SoV model, and the T2 control chart in MSPC is built to realize machining error detection according to the data characteristics of the above error model, which can judge whether the operation is out of control or not. If it is, then feedback is sent to the operations. The error model is modified by adjusting the operation out of control, and continually it is used to monitor operations. Finally, a machining instance containing two operations demonstrates the effectiveness of the machining error control method presented in this paper.展开更多
Characteristic finite difference fractional step schemes are put forward. The electric potential equation is described by a seven-point finite difference scheme, and the electron and hole concentration equations are t...Characteristic finite difference fractional step schemes are put forward. The electric potential equation is described by a seven-point finite difference scheme, and the electron and hole concentration equations are treated by a kind of characteristic finite difference fractional step methods. The temperature equation is described by a fractional step method. Thick and thin grids are made use of to form a complete set. Piecewise threefold quadratic interpolation, symmetrical extension, calculus of variations, commutativity of operator product, decomposition of high order difference operators and prior estimates are also made use of. Optimal order estimates in l2 norm are derived to determine the error of the approximate solution. The well-known problem is thorongley and completely solred.展开更多
Transient behavior of three-dimensional semiconductor device with heat conduc- tion is described by a coupled mathematical system of four quasi-linear partial differential equations with initial-boundary value conditi...Transient behavior of three-dimensional semiconductor device with heat conduc- tion is described by a coupled mathematical system of four quasi-linear partial differential equations with initial-boundary value conditions. The electric potential is defined by an ellip- tic equation and it appears in the following three equations via the electric field intensity. The electron concentration and the hole concentration are determined by convection-dominated diffusion equations and the temperature is interpreted by a heat conduction equation. A mixed finite volume element approximation, keeping physical conservation law, is used to get numerical values of the electric potential and the accuracy is improved one order. Two con- centrations and the heat conduction are computed by a fractional step method combined with second-order upwind differences. This method can overcome numerical oscillation, dispersion and decreases computational complexity. Then a three-dimensional problem is solved by computing three successive one-dimensional problems where the method of speedup is used and the computational work is greatly shortened. An optimal second-order error estimate in L2 norm is derived by using prior estimate theory and other special techniques of partial differential equations. This type of mass-conservative parallel method is important and is most valuable in numerical analysis and application of semiconductor device.展开更多
A new active control method was proposed, in which the analytical control law was deduced by using a step by step integral method to differential equation of motion under the condition of static error being zero. This...A new active control method was proposed, in which the analytical control law was deduced by using a step by step integral method to differential equation of motion under the condition of static error being zero. This control law is terse in mathematical expression and convenient for practical use. The simulation results demonstrate that the proposed method can provide much more remarkable peak response reduction of seismically excited structures than the classical LQR method.展开更多
The exponentially-distributed random timestepping algorithm with boundary test is implemented to evaluate the prices of some variety of single one-sided barrier option contracts within the framework of Black-Scholes m...The exponentially-distributed random timestepping algorithm with boundary test is implemented to evaluate the prices of some variety of single one-sided barrier option contracts within the framework of Black-Scholes model, giving efficient estimation of their hitting times. It is numerically shown that this algorithm, as for the Brownian bridge technique, can improve the rate of weak convergence from order one-half for the standard Monte Carlo to order 1. The exponential timestepping algorithm, however, displays better results, for a given amount of CPU time, than the Brownian bridge technique as the step size becomes larger or the volatility grows up. This is due to the features of the exponential distribution which is more strongly peaked near the origin and has a higher kurtosis compared to the normal distribution, giving more stability of the exponential timestepping algorithm at large time steps and high levels of volatility.展开更多
Although the step degree of nonlinearity has been introduced to conduct basic analysis and error propagation analysis for the pseudodynamic testing of nonlinear systems, it cannot be reliably used to select an appropr...Although the step degree of nonlinearity has been introduced to conduct basic analysis and error propagation analysis for the pseudodynamic testing of nonlinear systems, it cannot be reliably used to select an appropriate time step before performing a pseudodynamic test. Therefore, a novel parameter of instantaneous degree of nonlinearity is introduced to monitor the stiffness change at the end of a time step, and can thus be used to evaluate numerical and error propagation properties for nonlinear systems. Based on these properties, it is possible to select an appropriate time step to conduct a pseudodynamic test in advance. This possibility is very important in pseudodynamic testing, since the use of an arbitrary time step might lead to unreliable results or even destroy the test specimen. In this paper, guidelines are proposed for choosing an appropriate time step for accurate integration of nonlinear systems. These guidelines require estimation of the maximum instantaneous degree of nonlinearity and the solution of the initial natural frequency. The Newmark explicit method is chosen for this study. All the analytical results and the guidelines proposed are thoroughly confirmed with numerical examples.展开更多
Two important extensions of a technique to perform a nonlinear error propagation analysis for an explicit pseudodynamic algorithm （Chang, 2003） are presented. One extends the stability study from a given time step t...Two important extensions of a technique to perform a nonlinear error propagation analysis for an explicit pseudodynamic algorithm （Chang, 2003） are presented. One extends the stability study from a given time step to a complete step-by-step integration procedure. It is analytically proven that ensuring stability conditions in each time step leads to a stable computation of the entire step-by-step integration procedure. The other extension shows that the nonlinear error propagation results, which are derived for a nonlinear single degree of freedom （SDOF） system, can be applied to a nonlinear multiple degree of freedom （MDOF） system. This application is dependent upon the determination of the natural frequencies of the system in each time step, since all the numerical properties and error propagation properties in the time step are closely related to these frequencies. The results are derived from the step degree of nonlinearity. An instantaneous degree of nonlinearity is introduced to replace the step degree of nonlinearity and is shown to be easier to use in practice. The extensions can be also applied to the results derived from a SDOF system based on the instantaneous degree of nonlinearity, and hence a time step might be appropriately chosen to perform a pseudodynamic test prior to testing.展开更多
An aperture design technique using multi-step amplitude quantization for two-dimensional solid-state active phased arrays to achieve low sidelobe is described. It can be applied to antennas with arbitrary complex aper...An aperture design technique using multi-step amplitude quantization for two-dimensional solid-state active phased arrays to achieve low sidelobe is described. It can be applied to antennas with arbitrary complex aperture. Also, the gain drop and sidelobe degradation due to random amplitude and phase errors and element (or T/R module) failures are investigated.展开更多
基金financially supported by the National Natural Science Foundation of China(No.51275202)
文摘Flexible rolling is a forming process based on thickness reduction, and the precision of thickness reduction is the key factor affecting bending deformation. The major purpose of the present work is to solve the problem of bending deformation error caused by insufficient thickness reduction. Under the condition of different rolling reductions with the same sheet thickness and the same thickness reduction with different sheet thicknesses, the thickness reduction error of sheet metal is analyzed. In addition, the bending deformation of sheet metal under the same conditions is discussed and the influence of the multi-step forming process on the thickness reduction error is studied. The results show that, under the condition of the same sheet thickness, the thickness reduction error increases with increasing rolling reduction because of an increase in work hardening. As rolling reduction increases, the longitudinal bending deformation decreases because of the decrease of the maximum thickness difference. Under the condition with the same thickness reduction, the thickness reduction error increases because of the decrease of the rolling force with increasing sheet thickness. As the sheet thickness increases, the longitudinal bending deformation increases because of the increase in the maximum thickness difference. A larger bending deformation is divided into a number of small bending deformations in a multi-step forming process, avoiding a sharp increase in the degree of work hardening; the thickness reduction error is effectively reduced in the multi-step forming process. Numerical simulation results agree with the results of the forming experiments.
文摘近年来,超宽带(Ultra-wideband,UWB)通信技术因其具有数据传输速率高、功耗低、保密性高、成本低等诸多优点,成为室内高速数据传输的一种有效解决方案。由于高速通信下码间串扰极大地影响了UWB系统的接收性能,需要在解调前采用Rake接收机和均衡等手段消除码间串扰。针对自适应最小误码率(Adaptive Minimum Bit Error Rate,AMBER)均衡算法与Rake接收机结合进行研究,提出了一种变步长自适应最小误码率(Variable Step-Adaptive Minimum Bit Error Rate,VS-AMBER)均衡算法,在较低信噪比和较高信噪比情况下分别使用不同的变步长方案,较高信噪比下在收敛速度和收敛精度上有所提升,较低信噪比下降低了误码率和功耗。
文摘摆线泵转子的齿廓形状和加工精度决定了齿轮泵容腔的密封性,进而影响吸油和压油等运动特性。然而,转子的齿廓形状多是企业根据自身实际需求自行设计的,这就造成齿廓误差测量过程中的测量基准和设计基准不一致,测量结果更无法准确反映转子的齿廓加工质量。鉴于此,将企业设计的产品模型数据交互规范(Standard for the Exchange of Product model data, STEP)齿廓作为测量所必需的基准数据,在使用一维测头的国产齿轮测量中心上完成了转子齿廓的快速检测,采用重构及匹配等补偿处理方法,实现了摆线泵转子误差的精确评定。结果表明,该方法具有较好的柔性,对于复杂齿面的精确测量和评定具有重要的理论意义。
基金Hundred Talent Program of Chinese Academy of Sciences under Grant No. 0300YQ000101. Partly supported by the National Natural Sci
文摘Errors due to split time stepping are discussed for an explicit free–surface ocean model. In commonly used split time stepping, the way of time integration for the barotropic momentum equation is not compatible with that of the baroclinic one. The baroclinic equation has three–time–level structure because of leapfrog scheme. The barotropic one, however, has two–time–level structure when represented in terms of the baroclinic time level, on which the baroclinic one is integrated. This incompatibility results in the splitting errors as shown in this paper. The proper split time stepping is therefore proposed in such a way that the compatibility is kept between the barotropic and baroclinic equations. Its splitting errors are shown extremely small, so that it is particularly relevant to long–term integration for climate studies. It is applied to a free–surface model for the North Pacific Ocean.
基金National Natural Science Foundation of China (70931004)
文摘For aircraft manufacturing industries, the analyses and prediction of part machining error during machining process are very important to control and improve part machining quality. In order to effectively control machining error, the method of integrating multivariate statistical process control （MSPC） and stream of variations （SoV） is proposed. Firstly, machining error is modeled by multi-operation approaches for part machining process. SoV is adopted to establish the mathematic model of the relationship between the error of upstream operations and the error of downstream operations. Here error sources not only include the influence of upstream operations but also include many of other error sources. The standard model and the predicted model about SoV are built respectively by whether the operation is done or not to satisfy different requests during part machining process. Secondly, the method of one-step ahead forecast error （OSFE） is used to eliminate autocorrelativity of the sample data from the SoV model, and the T2 control chart in MSPC is built to realize machining error detection according to the data characteristics of the above error model, which can judge whether the operation is out of control or not. If it is, then feedback is sent to the operations. The error model is modified by adjusting the operation out of control, and continually it is used to monitor operations. Finally, a machining instance containing two operations demonstrates the effectiveness of the machining error control method presented in this paper.
基金This work is supported by the Major State Basic Research Program of China (19990328), the National Tackling Key Problem Program, the National Science Foundation of China (10271066 and 0372052), and the Doctorate Foundation of the Ministry of Education of China (20030422047).
文摘Characteristic finite difference fractional step schemes are put forward. The electric potential equation is described by a seven-point finite difference scheme, and the electron and hole concentration equations are treated by a kind of characteristic finite difference fractional step methods. The temperature equation is described by a fractional step method. Thick and thin grids are made use of to form a complete set. Piecewise threefold quadratic interpolation, symmetrical extension, calculus of variations, commutativity of operator product, decomposition of high order difference operators and prior estimates are also made use of. Optimal order estimates in l2 norm are derived to determine the error of the approximate solution. The well-known problem is thorongley and completely solred.
基金supported by National Natural Science Foundation of China(11101244,11271231)National Tackling Key Problems Program(20050200069)Doctorate Foundation of the Ministry of Education of China(20030422047)
文摘Transient behavior of three-dimensional semiconductor device with heat conduc- tion is described by a coupled mathematical system of four quasi-linear partial differential equations with initial-boundary value conditions. The electric potential is defined by an ellip- tic equation and it appears in the following three equations via the electric field intensity. The electron concentration and the hole concentration are determined by convection-dominated diffusion equations and the temperature is interpreted by a heat conduction equation. A mixed finite volume element approximation, keeping physical conservation law, is used to get numerical values of the electric potential and the accuracy is improved one order. Two con- centrations and the heat conduction are computed by a fractional step method combined with second-order upwind differences. This method can overcome numerical oscillation, dispersion and decreases computational complexity. Then a three-dimensional problem is solved by computing three successive one-dimensional problems where the method of speedup is used and the computational work is greatly shortened. An optimal second-order error estimate in L2 norm is derived by using prior estimate theory and other special techniques of partial differential equations. This type of mass-conservative parallel method is important and is most valuable in numerical analysis and application of semiconductor device.
文摘A new active control method was proposed, in which the analytical control law was deduced by using a step by step integral method to differential equation of motion under the condition of static error being zero. This control law is terse in mathematical expression and convenient for practical use. The simulation results demonstrate that the proposed method can provide much more remarkable peak response reduction of seismically excited structures than the classical LQR method.
文摘The exponentially-distributed random timestepping algorithm with boundary test is implemented to evaluate the prices of some variety of single one-sided barrier option contracts within the framework of Black-Scholes model, giving efficient estimation of their hitting times. It is numerically shown that this algorithm, as for the Brownian bridge technique, can improve the rate of weak convergence from order one-half for the standard Monte Carlo to order 1. The exponential timestepping algorithm, however, displays better results, for a given amount of CPU time, than the Brownian bridge technique as the step size becomes larger or the volatility grows up. This is due to the features of the exponential distribution which is more strongly peaked near the origin and has a higher kurtosis compared to the normal distribution, giving more stability of the exponential timestepping algorithm at large time steps and high levels of volatility.
基金supported by the NSC,Chinese Taipei,Under Grant No.NSC-95-2221-E-027-099
文摘Although the step degree of nonlinearity has been introduced to conduct basic analysis and error propagation analysis for the pseudodynamic testing of nonlinear systems, it cannot be reliably used to select an appropriate time step before performing a pseudodynamic test. Therefore, a novel parameter of instantaneous degree of nonlinearity is introduced to monitor the stiffness change at the end of a time step, and can thus be used to evaluate numerical and error propagation properties for nonlinear systems. Based on these properties, it is possible to select an appropriate time step to conduct a pseudodynamic test in advance. This possibility is very important in pseudodynamic testing, since the use of an arbitrary time step might lead to unreliable results or even destroy the test specimen. In this paper, guidelines are proposed for choosing an appropriate time step for accurate integration of nonlinear systems. These guidelines require estimation of the maximum instantaneous degree of nonlinearity and the solution of the initial natural frequency. The Newmark explicit method is chosen for this study. All the analytical results and the guidelines proposed are thoroughly confirmed with numerical examples.
基金NSC, Chinese Taipei Under Grant No. NSC-97-2221-E-027-036-MY2
文摘Two important extensions of a technique to perform a nonlinear error propagation analysis for an explicit pseudodynamic algorithm （Chang, 2003） are presented. One extends the stability study from a given time step to a complete step-by-step integration procedure. It is analytically proven that ensuring stability conditions in each time step leads to a stable computation of the entire step-by-step integration procedure. The other extension shows that the nonlinear error propagation results, which are derived for a nonlinear single degree of freedom （SDOF） system, can be applied to a nonlinear multiple degree of freedom （MDOF） system. This application is dependent upon the determination of the natural frequencies of the system in each time step, since all the numerical properties and error propagation properties in the time step are closely related to these frequencies. The results are derived from the step degree of nonlinearity. An instantaneous degree of nonlinearity is introduced to replace the step degree of nonlinearity and is shown to be easier to use in practice. The extensions can be also applied to the results derived from a SDOF system based on the instantaneous degree of nonlinearity, and hence a time step might be appropriately chosen to perform a pseudodynamic test prior to testing.
文摘An aperture design technique using multi-step amplitude quantization for two-dimensional solid-state active phased arrays to achieve low sidelobe is described. It can be applied to antennas with arbitrary complex aperture. Also, the gain drop and sidelobe degradation due to random amplitude and phase errors and element (or T/R module) failures are investigated.
