A steel-concrete composite cable-stayed bridge features integrated steel girders and concrete decks linked by shear connectors to support loads,but stress concentration in wet joints can lead to cracking.In-situ tests...A steel-concrete composite cable-stayed bridge features integrated steel girders and concrete decks linked by shear connectors to support loads,but stress concentration in wet joints can lead to cracking.In-situ tests were conducted on key sections of steel-concrete composite cable-stayed bridges to analyze the stress-strain evolution of wet joints under environmental factors,constraints,and complex construction processes.The coordinated working performance of the bridge decks was also analyzed.The results indicate that temperature is the key factor affecting the stresses and strains in wet joint concrete.Approximately 7 days after casting the wet joint concrete,the strains at each measurement point of the wet joint are approximately negatively correlated with the temperature change at the measurement point.Different locations within the wet joints have respective impacts,presenting potential weak points.Construction conditions have a certain impact on the stress and strain of the wet joint.The top deck of the steel box girder is not fully bonded to the bottom surface of the wet joints,resulting in a certain strain difference after loading.To further analyze the cooperative working performance of steel box girders and concrete wet joint bridge deck systems,finite element analysis was conducted on composite girder structures.A stiffness calculation method for shear connectors based on numerical simulation was proposed.The results indicate that strain differences can cause interface slip in composite girders.This slip leads to increased deflection of the composite girders and increased tensile stress in the bottom plate of the steel box girders.This study clarifies the stress conditions and factors affecting wet joints during construction,preventing early cracking,and offers precise data for a full bridge finite element model.展开更多
In order to more accurately calculate the fatigue damage and fatigue life of steel-concrete composite beam under standard vehicle load,the steel beam components of a large-span steel-concrete composite beam suspension...In order to more accurately calculate the fatigue damage and fatigue life of steel-concrete composite beam under standard vehicle load,the steel beam components of a large-span steel-concrete composite beam suspension bridge were taken as the research object.Based on the S-N curve and linear fatigue damage theory,a standard segment model was established.Accordingly,the welding position of the secondary longitudinal beam was identified as the focus fatigue point,and the stress time course calculation was done for the point.The results showed that when the vehicle mass increases from 50 t to 100 t,the amount of fatigue damage will increase by more than 5 times in the same period of time,and the increase in the vehicle mass will reduce the fatigue life of the bridge structure.The fatigue damage of bridge structures increases with the increase of vehicle speed.The increase rate of fatigue damage is greater at low speeds,and the increase rate of fatigue damage slows down at high speeds.展开更多
The stiffness matrix of semi-rigidly connected composite beams considering interface slip was established and the calculation method for elastic seismic response of composite frame was derived.The corresponding calcul...The stiffness matrix of semi-rigidly connected composite beams considering interface slip was established and the calculation method for elastic seismic response of composite frame was derived.The corresponding calculation programs were developed.Introducing the dimensionless quantities that were related to the connector shearing stiffness and the joint rotation stiffness,the influences of interface slip and semi-rigid joint on composite frame were transferred to quantitative parameter analysis,taking account of cross sectional properties,materials and linear stiffness of composite beam synthetically.Based on the calculation programs,free vibration frequencies and seismic responses of semi-rigid joint steel-concrete composite frame considering interface slip were calculated.The influences of interface slip and semi rigid joint on dynamic characteristics and seismic response were analyzed and the seismic design advices were presented.The results show that the interface slip decreases the free vibration frequencies and increase the seismic responses of composite frame.The semi-rigid joint reduces the free vibration frequencies and increases seismic responses of composite frame compared with rigid joint.With the increase of joint rotational stiffness,the elastic seismic responses of composite frame increase firstly and then decrease.The effects are related to the ratio of joint rotation stiffness to linear stiffness of composite beam.展开更多
A new type of semi-rigid thin-walled steel-concrete composite beam-to-column joint has been proposed in this paper.Five semi-rigid composite beam-to-column joint specimens subjected to hogging moments under monotonic ...A new type of semi-rigid thin-walled steel-concrete composite beam-to-column joint has been proposed in this paper.Five semi-rigid composite beam-to-column joint specimens subjected to hogging moments under monotonic loading were tested to study the static behavior of this new type of joint.The main variable parameters for the five joint specimens were the longitudinal reinforcement ratio and the joint type.The experimental results designated that the magnitude of extension of the longitudinal reinforcement is the most important factor that influenced the moment-rotation characteristic of the new type of joint.The concrete slabs could resist 3.8%-19.1% of the total shear load applied to the cross-sections near the beam-to-column connection.The edge stiffened elements,such as the flange of the lipped I-section thin-walled steel beam,were capable of having considerable inelastic deformation capacity although they had comparatively large width-to-thickness ratios.The shear failure of the concrete cantilever edge strip must be taken into account in practical design because it has significant influence on the anchorage of the longitudinal reinforcement in the new type of external joints.展开更多
The solar temperature field of a large three-span continuous bridge with steel-concrete composite box girder and variable cross-section is measured to verify a calculation method for the temperature field of steel-con...The solar temperature field of a large three-span continuous bridge with steel-concrete composite box girder and variable cross-section is measured to verify a calculation method for the temperature field of steel-concrete composite beams. The test results show that the temperature of an external steel web- plate is higher than that of an internal web-plate due to the difference in solar radiation. Air temperature inside the box matches the average temperature of the whole steel box. Based on actual measurements, a transient thermal analysis with multiple boundary conditions is also carried out by a software program ANSYS. Convective boundary situation and states of solar radiation on steel web plates in different situations are determined in the analysis. The feature of the temperature field is preliminarily achieved through a comparative study between the actual measurement and the finite element analysis. The computed results are in good consistence with the actual measurement results, with the maximum difference within 2 ℃. This indicates that the theoretical calculation method is reliable and it provides a foundation for further research on temperature field distribution in the steel-concrete composite box girder.展开更多
Static load tests and bearing capacity analyses are carried out for two outer-plated steel-concrete continuous composite beams. The load-deflection curve and the load-strain curve of specimens are obtained and analyze...Static load tests and bearing capacity analyses are carried out for two outer-plated steel-concrete continuous composite beams. The load-deflection curve and the load-strain curve of specimens are obtained and analyzed. The test results indicate that effective cooperation can be achieved by the shearresistant connection between the reinforcement in the negative moment area and the outer-plated steel beam, and the overall working performance of the composite beams is favorable. At the load-bearing limiting state, the plastic strain on the maximum negative and positive moment section becomes fully developed so as to form relatively ideal plastic hinges. With the increase in the reinforcement ratio, the moment-carrying capacity of the composite beams improves significantly, but the ductility of the beams and the rotation ability of the plastic hinges decrease. The formulae for calculating the limit bending capacity in the negative moment area of outer-plated steel-concrete composite beams are proposed based on the test data. The calculated results agree well with the test results.展开更多
In order to establish the relationship between the measured dynamic response and the health status of long-span bridges, a double-layer model updating method for steel-concrete composite beam cable-stayed bridges is p...In order to establish the relationship between the measured dynamic response and the health status of long-span bridges, a double-layer model updating method for steel-concrete composite beam cable-stayed bridges is proposed. Measured frequencies are selected as the first-layer reference data, and the mass of the bridge deck, the grid density, the modulus of concrete and the ballast on the side span are modified by using a manual tuning technique. Measured global positioning system （GPS） data is selected as the second-layer reference data, and the degradation of the integral structure stiffness EI of the whole bridge is taken into account for the second-layer model updating by using the finite element iteration algorithm. The Nanpu Bridge in Shanghai is taken as a case to verify the applicability of the proposed model updating method. After the first-layer model updating, the standard deviation of modal frequencies is smaller than 7%. After the second-layer model updating, the error of the deflection of the mid-span is smaller than 10%. The integral structure stiffness of the whole bridge decreases about 20%. The research results show a good agreement between the calculated response and the measured response.展开更多
An accurate finite element （ FE） model was constructed to examine the hysteretic behavior of double-skin steel-concrete composite box （ DSCB） piers for further understanding the seismic performance of DSCB piers;...An accurate finite element （ FE） model was constructed to examine the hysteretic behavior of double-skin steel-concrete composite box （ DSCB） piers for further understanding the seismic performance of DSCB piers; where the local buckling behavior of steel tubes, the confinement of the in-filled concrete and the interface action between steel tube and in-filled concrete were considered. The accuracy of the proposed FE model was verified by the bidirectional cyclic loading test results. Based on the validated FE model, the effects of some key parameters, such as section width to steel thickness ratio, slenderness ratio, aspect ratio and axial load ratio on the hysteretic behavior of DSCB piers were investigated. Finally, the skeleton curve model of DSCB piers was proposed. The numerical simulation results reveal that the peak strength and elastic stiffness decrease with the increase of the section width to steel thickness ratio. Moreover, the increase of the slenderness ratio may result in a significant reduction in the peak strength and elastic stiffness while the ultimate displacement increases. The proposed skeleton curve model can be taken as a reference for seismic performance analyses of the DSCB piers.展开更多
Joints are widely distributed structural defects in rock masses,and their geometric characteristics play a decisive role in the overall stability of rocks under complex stress conditions.To clarify the influence of jo...Joints are widely distributed structural defects in rock masses,and their geometric characteristics play a decisive role in the overall stability of rocks under complex stress conditions.To clarify the influence of joint geometry on the mechanical behavior of jointed rock under such conditions,this study investigated the mechanical properties and failure mechanisms of composite jointed rock specimens with varying joint roughness and joint dip angles.Three typical failure modes under triaxial loading were identified,and a mechanical analysis model incorporating joint roughness and dip angle was established.The failure mechanism was revealed,and a discrete element model was developed to analyze the micro-damage evolution process of the specimens.The results show that the mechanical parameters of the specimens exhibit pronounced anisotropy.Both the elastic modulus and peak strength reach their minimum values at a joint dip angle of 60°.Increasing joint roughness significantly reduces the degree of anisotropy and enhances the energy storage capacity of the specimens.A strong linear relationship is observed between the elastic strain energy and the peak deviatoric stress,confirming the applicability of the linear energy storage law in composite jointed rocks.Discrete element simulations revealed the evolution path and dominant types of microcracks between the joint and matrix.The joint dip angle governs the transition of dominant crack types from tensile to shear and then back to tensile.Increased joint roughness significantly suppresses damage localization along the joint and results in an approximately 20%increase in the proportion of shear microcracks within the matrix.These findings clarify the regulatory role of joint geometrical parameters in the damage evolution process.展开更多
Ni/TiAl composite brazed joints could significantly reduce the aircraft’s weight.However,low interfacial adhesion,coarse and brittle-hard intermetallic compounds(IMCs)seriously limited the application of Ni/TiAl comp...Ni/TiAl composite brazed joints could significantly reduce the aircraft’s weight.However,low interfacial adhesion,coarse and brittle-hard intermetallic compounds(IMCs)seriously limited the application of Ni/TiAl composite joints in the next generation of aerospace applications.So enhanced K4169/TiAl composite joints were investigated by vacuum brazed with(Ni_(53.33)Cr_(20)B_(16.67)Si_(10)/Zr_(25)Ti_(18.75)Ta_(12.5)Ni_(25)Cu_(18.75))composite filler metal(CFM)designed based on cluster-plus-glue-atom model.The shear strength of the joint reached 485 MPa,comparable to the 491 MPa of TiAl substrate.The flat and brittle-hard diffusion reaction layer between Zones I and II was eliminated,simultaneously generating CrB4 dispersion strengthening due to the CFM developed with the interfacial solid-liquid space-time hysteresis effect.In Zones II and III,IMCs all transformed into Niss(Cr,Fe)_([0–88]),Niss(Ti,Al)_([004]),and Niss(Zr,Si)_([11–2])of circular and oval shapes through isothermal solidification.Meanwhile,the residual stresses and hardness were distributed in reticulated cladding characteristics.Thereby,lattice distortion led to solid solution strengthening and increased plastic toughness through crack termination and bridging mechanisms,which inhibited dislocations from plugging and crack propagation.Various interfaces in ZoneⅣwere regulated into semi-and coherent interfaces.Ni3(Ti,Al)/(Ni,Ti,Al)and(Ni,Ti,Al)/AlNi_(2)Ti were composed of higher interfacial bonding energy(2.771 J/m^(2),2.547 J/m^(2))and Ni-Ni covalent bonds.Interfacial covalent bonding and large interfacial bonding energy coupling strengthened Zone IV.Consequently,cracks initiated at the(Ni,Ti,Al)[013]/Ti3Al_([010])and expanded rapidly into TiAl substrate.Therefore,applying this method to design CFMs and regulate the phase,grain morphology,and interface’s fine structure could provide new pathways for dissimilar hard-to-join metals.展开更多
Based on Hamilton principle,the governing differential equations and the corresponding boundary conditions of steel-concrete composite box girder with consideration of the shear lag effect meeting self equilibrated st...Based on Hamilton principle,the governing differential equations and the corresponding boundary conditions of steel-concrete composite box girder with consideration of the shear lag effect meeting self equilibrated stress,shear deformation,slip,as well as rotational inertia were induced.Therefore,natural frequency equations were obtained for the boundary types,such as simple support,cantilever,continuous girder and fixed support at two ends.The ANSYS finite element solutions were compared with the analytical solutions by calculation examples and the validity of the proposed approach was verified,which also shows the correctness of longitudinal warping displacement functions.Some meaningful conclusions for engineering design were obtained.The decrease extent of each order natural frequency of the steel-concrete composite box-girder is great under action of the shear lag effect.The shear-lag effect of steel-concrete composite box girder increases when frequency order rises,and increases while span-width ratio decreases.The proposed approach provides theoretical basis for further research of free vibration characteristics of steel-concrete composite box-girder.展开更多
The connection efficiency of composite pre-tightened multi-tooth joint is low because of uneven load distribution and single load transmission path.In this paper,based on the principle of bio-tooth(suture)structure,co...The connection efficiency of composite pre-tightened multi-tooth joint is low because of uneven load distribution and single load transmission path.In this paper,based on the principle of bio-tooth(suture)structure,combining soft material with fractal,a composite pre-tightened multi-hierarchy tooth joint is proposed,and the bearing performance and failure process of the joint through experiments and finite element method under tensile load.First,the ultimate bearing capacity,load distribution ratio,and failure process of different hierarchies of teeth joints are studied through experiments.Then,the progressive damage models of different hierarchies of tooth joints are established,and experiments verify the validity of the finite element model.Finally,the effects of soft material and increasing tooth hierarchy on the failure process and bearing capacity of composite pre-tightened tooth joints are analyzed by the finite element method.The following conclusions can be drawn:(1)The embedding of soft materials changed the failure process of the joint.Increasing the tooth hierarchy can give the joint more load transfer paths,but the failure process of the joint is complicated.(2)Embedding soft materials and increasing the tooth hierarchy simultaneously can effectively improve the bearing capacity of composite pre-tightened tooth joints,which is 87.8%higher than that of traditional three-tooth joints.展开更多
Based on the consideration of longitudinal warp caused by shear lag effects on concrete slabs and bottom plates of steel beams,shear deformation of steel beams and interface slip between steel beams and concrete slabs...Based on the consideration of longitudinal warp caused by shear lag effects on concrete slabs and bottom plates of steel beams,shear deformation of steel beams and interface slip between steel beams and concrete slabs,the governing differential equations and boundary conditions of the steel-concrete composite box beams under lateral loading were derived using energy-variational method.The closed-form solutions for stress,deflection and slip of box beams under lateral loading were obtained,and the comparison of the analytical results and the experimental results for steel-concrete composite box beams under concentrated loading or uniform loading verifies the closed-form solution.The investigation of the parameters of load effects on composite box beams shows that:1) Slip stiffness has considerable impact on mid-span deflection and end slip when it is comparatively small;the mid-span deflection and end slip decrease significantly with the increase of slip stiffness,but when the slip stiffness reaches a certain value,its impact on mid-span deflection and end slip decreases to be negligible.2) The shear deformation has certain influence on mid-span deflection,and the larger the load is,the greater the influence is.3) The impact of shear deformation on end slip can be neglected.4) The strain of bottom plate of steel beam decreases with the increase of slip stiffness,while the shear lag effect becomes more significant.展开更多
6061 aluminum alloy was successfully vacuum brazed to 304 stainless steel using Al-Si-Ge/Cu composite filler metal.The thermodynamic model was established to analyze the formation mechanism of microstructure in brazed...6061 aluminum alloy was successfully vacuum brazed to 304 stainless steel using Al-Si-Ge/Cu composite filler metal.The thermodynamic model was established to analyze the formation mechanism of microstructure in brazed joint and element diffusion behavior between filler metal and substrate.The findings indicated that the microstructure of 6061 aluminum alloy/304 stainless steel joint was a multilayer structure composed of three zones(ZoneⅠ,ZoneⅡand ZoneⅢ).The free energy(△G)calculation results indicated that Al-Si-M(M was Fe,Cr,Ni and Cu)ternary intermetallic compounds(IMCs)formed,when on M-Al side and M-Si/Ge side was similar.And only Al-M binary IMCs would be generated when there was large difference between on M-Al side and that on M-Si/Ge side.The calculation results of chemical potential of Si△_(μSi)and Ge△_(μGe)indicated that there was continuous Si and Ge diffusion toward Zone I,forming(Ge,Si)layer.The segregation of Si and Ge hindered the diffusion of Cr toward Zone II and promoted its diffusion toward(Ge,Si)layer,leading to an upward trend of Cr distribution in Al7(Fe,Cr)2Si layer.Negative△_(μNi)and△_(μFe)were responsible for continuous diffusion of Fe and Ni toward Zone II.The small difference between△_(μcu)in Zone I and Zone II contributed to distribution of CuAl2 in Zone II.The formation mechanism of joint could be mainly divided into four steps.展开更多
Steel-concrete composite frames are seeing increased use in earthquake region because of their excellent structural characteristics, including high strength, stiffness, and good ductility. However, there exist gaps in...Steel-concrete composite frames are seeing increased use in earthquake region because of their excellent structural characteristics, including high strength, stiffness, and good ductility. However, there exist gaps in the knowledge of seismic behavior and the design provisions for these structures. In order to better understand the seismic behaviors of composite frame systems, eight steel-concrete composite frames were designed. These composite frames were composed of steel-concrete composite beams and concrete filled steel tube columns. The axial compression ratio of column, slenderness ratio and linear stiffness ratio of beam to column were selected as main design parameters. The low reversed cyclic loading tests of composite frame system were carried out. Based on test results, the seismic behaviors of composite frames such as failure mode, hysteresis curve, strength degradation, rigidity degradation, ductility and energy dissipation were studied. Known from the test phenomenon, the main cause of damage is the out-of-plane deformation of steel beam and the yielding destruction of column heel. The hysteretic loops of composite frame appear a spindle shape and no obvious pinch phenomenon. The results demonstrate that this type of composite frame has favorable seismic behaviors. Furthermore, the effects of design parameters on seismic behaviors were also discussed. The results of the experiment show that the different design parameter has different influence rule on seismic behaviors of composite frame.展开更多
Adopting a steel-anchor beam and steel corbel composite structure in the anchor zone on pylon is one of the key techniques for the design of Jintang bridge, a cable-stayed bridge in Zhoushan, China. In order to ensure...Adopting a steel-anchor beam and steel corbel composite structure in the anchor zone on pylon is one of the key techniques for the design of Jintang bridge, a cable-stayed bridge in Zhoushan, China. In order to ensure the safety of the steel-concrete composite structure, a stud connector model for the joint section was put forward. Experiments were conducted to obtain the relation between load and slip of specimen, the failure pattern of stud connector, the yield bearing capacity and ultimate bearing capacity of a single stud, etc. The whole process of the structural behavior of the specimen was comprehensively analyzed. The features of the internal force distribution in the steel-concrete composite structure and the strain distribution of stud connector under different loads were emphatically studied. The test results show that the stud connector is applicable for the steel-concrete composite structure for pylon of Jintang bridge. The stud has a good ductility performance and a obvious yield process before its destruction. The stud connector basically works in a state of elasticity under a load less than the yield load.展开更多
Proposes a simplified finite element model for steel-concrete composite beams. The effects of slip can be taken into account by creating a special matrix of shear connector stiffness and using the iteration method. Me...Proposes a simplified finite element model for steel-concrete composite beams. The effects of slip can be taken into account by creating a special matrix of shear connector stiffness and using the iteration method. Meanwhile, the effect of material non-linearity of steel and concrete on rigidity and strength of composite beams is considered. With the age-adjusted effective modulus method, the analysis for the whole process of shrinkage and creep under long-term load can be performed. The ultimate load, deflection, stress and slip of continuous composite beams under short-term and long-term load are computed using the proposed finite element model. The numerical results are compared with the experimental results and existing values based on other numerical methods, and are found to be in good agreement.展开更多
Slip of a composite box beam may reduce its stiffness, enlarge its deformation and affect its performance. In this work, the governing differential equations and boundary conditions of composite box beams were establi...Slip of a composite box beam may reduce its stiffness, enlarge its deformation and affect its performance. In this work, the governing differential equations and boundary conditions of composite box beams were established. Analytic solutions of combined differential equations were also established. Partial degree of freedom was adopted to establish a new FEA element of three-dimensional beam, taking into account the slip effect. Slip and its first-order derivative were introduced into the nodes of composite box beams as generalized degree of freedom. Stiffness matrix and load array of beam elements were established. A three-dimensional nonlinear calculation program was worked out. The results show that the element is reliable and easy to divide and is suitable for special nonlinear analysis of large-span composite box beams.展开更多
This work experimentally investigates the effects of shear stud characteristics on the interface slippage of steel-concrete composite push-out specimens. ABAQUS is used to establish a detailed 3D finite element(FE) mo...This work experimentally investigates the effects of shear stud characteristics on the interface slippage of steel-concrete composite push-out specimens. ABAQUS is used to establish a detailed 3D finite element(FE) model and analyze the behavior of push-out specimens. The modeling results are in good agreement with the experimental results. Based on parametrical analysis using the validated FE approaches, the effects of important design parameters, such as the diameter, number, length to diameter ratio, and yield strength of studs, concrete strength and steel transverse reinforcement ratio, on the load-slip relationship at the interface of composite beams are discussed. In addition, a simplified approach to model studs is developed using virtual springs with an equivalent stiffness. This approach is demonstrated to be able to predict the load-displacement response and ultimate bearing capacity of steel-concrete composite beams. The predicted results show satisfactory agreement with experimental results from the literature.展开更多
To improve the quality of the steel-concrete composite segment of the box girder,to ensure the compactness of concrete to avoid debonding and to enhance the fatigue strength of concrete are critical to the concrete pr...To improve the quality of the steel-concrete composite segment of the box girder,to ensure the compactness of concrete to avoid debonding and to enhance the fatigue strength of concrete are critical to the concrete preparation for such site. Furthermore,the coordination ability to deformation between steel and concrete is also important because of great difference of the elastic modulus between them. Concrete for the steel-concrete composite segment with high fluidity,excellent crack resistance and low shrinkage was prepared by adding efficient poly-carboxylic water-reducing agent,high quality fly ash and expansion agent to it. The quality of the concrete of the half partial testing block showed that the optimal mix proportion of polypropylene fiber reinforced concrete had achieved expected effect,ensured high quality,thus meeting the requirements of construction.展开更多
文摘A steel-concrete composite cable-stayed bridge features integrated steel girders and concrete decks linked by shear connectors to support loads,but stress concentration in wet joints can lead to cracking.In-situ tests were conducted on key sections of steel-concrete composite cable-stayed bridges to analyze the stress-strain evolution of wet joints under environmental factors,constraints,and complex construction processes.The coordinated working performance of the bridge decks was also analyzed.The results indicate that temperature is the key factor affecting the stresses and strains in wet joint concrete.Approximately 7 days after casting the wet joint concrete,the strains at each measurement point of the wet joint are approximately negatively correlated with the temperature change at the measurement point.Different locations within the wet joints have respective impacts,presenting potential weak points.Construction conditions have a certain impact on the stress and strain of the wet joint.The top deck of the steel box girder is not fully bonded to the bottom surface of the wet joints,resulting in a certain strain difference after loading.To further analyze the cooperative working performance of steel box girders and concrete wet joint bridge deck systems,finite element analysis was conducted on composite girder structures.A stiffness calculation method for shear connectors based on numerical simulation was proposed.The results indicate that strain differences can cause interface slip in composite girders.This slip leads to increased deflection of the composite girders and increased tensile stress in the bottom plate of the steel box girders.This study clarifies the stress conditions and factors affecting wet joints during construction,preventing early cracking,and offers precise data for a full bridge finite element model.
文摘In order to more accurately calculate the fatigue damage and fatigue life of steel-concrete composite beam under standard vehicle load,the steel beam components of a large-span steel-concrete composite beam suspension bridge were taken as the research object.Based on the S-N curve and linear fatigue damage theory,a standard segment model was established.Accordingly,the welding position of the secondary longitudinal beam was identified as the focus fatigue point,and the stress time course calculation was done for the point.The results showed that when the vehicle mass increases from 50 t to 100 t,the amount of fatigue damage will increase by more than 5 times in the same period of time,and the increase in the vehicle mass will reduce the fatigue life of the bridge structure.The fatigue damage of bridge structures increases with the increase of vehicle speed.The increase rate of fatigue damage is greater at low speeds,and the increase rate of fatigue damage slows down at high speeds.
基金Project(50778177) supported by the National Natural Science Foundation of ChinaProject(07JJ1009) supported by the Outstanding Younger Fund of Hunan Province,China
文摘The stiffness matrix of semi-rigidly connected composite beams considering interface slip was established and the calculation method for elastic seismic response of composite frame was derived.The corresponding calculation programs were developed.Introducing the dimensionless quantities that were related to the connector shearing stiffness and the joint rotation stiffness,the influences of interface slip and semi-rigid joint on composite frame were transferred to quantitative parameter analysis,taking account of cross sectional properties,materials and linear stiffness of composite beam synthetically.Based on the calculation programs,free vibration frequencies and seismic responses of semi-rigid joint steel-concrete composite frame considering interface slip were calculated.The influences of interface slip and semi rigid joint on dynamic characteristics and seismic response were analyzed and the seismic design advices were presented.The results show that the interface slip decreases the free vibration frequencies and increase the seismic responses of composite frame.The semi-rigid joint reduces the free vibration frequencies and increases seismic responses of composite frame compared with rigid joint.With the increase of joint rotational stiffness,the elastic seismic responses of composite frame increase firstly and then decrease.The effects are related to the ratio of joint rotation stiffness to linear stiffness of composite beam.
基金Sponsored by the National Natural Science Foundation of China (Grant No.50478027)
文摘A new type of semi-rigid thin-walled steel-concrete composite beam-to-column joint has been proposed in this paper.Five semi-rigid composite beam-to-column joint specimens subjected to hogging moments under monotonic loading were tested to study the static behavior of this new type of joint.The main variable parameters for the five joint specimens were the longitudinal reinforcement ratio and the joint type.The experimental results designated that the magnitude of extension of the longitudinal reinforcement is the most important factor that influenced the moment-rotation characteristic of the new type of joint.The concrete slabs could resist 3.8%-19.1% of the total shear load applied to the cross-sections near the beam-to-column connection.The edge stiffened elements,such as the flange of the lipped I-section thin-walled steel beam,were capable of having considerable inelastic deformation capacity although they had comparatively large width-to-thickness ratios.The shear failure of the concrete cantilever edge strip must be taken into account in practical design because it has significant influence on the anchorage of the longitudinal reinforcement in the new type of external joints.
文摘The solar temperature field of a large three-span continuous bridge with steel-concrete composite box girder and variable cross-section is measured to verify a calculation method for the temperature field of steel-concrete composite beams. The test results show that the temperature of an external steel web- plate is higher than that of an internal web-plate due to the difference in solar radiation. Air temperature inside the box matches the average temperature of the whole steel box. Based on actual measurements, a transient thermal analysis with multiple boundary conditions is also carried out by a software program ANSYS. Convective boundary situation and states of solar radiation on steel web plates in different situations are determined in the analysis. The feature of the temperature field is preliminarily achieved through a comparative study between the actual measurement and the finite element analysis. The computed results are in good consistence with the actual measurement results, with the maximum difference within 2 ℃. This indicates that the theoretical calculation method is reliable and it provides a foundation for further research on temperature field distribution in the steel-concrete composite box girder.
文摘Static load tests and bearing capacity analyses are carried out for two outer-plated steel-concrete continuous composite beams. The load-deflection curve and the load-strain curve of specimens are obtained and analyzed. The test results indicate that effective cooperation can be achieved by the shearresistant connection between the reinforcement in the negative moment area and the outer-plated steel beam, and the overall working performance of the composite beams is favorable. At the load-bearing limiting state, the plastic strain on the maximum negative and positive moment section becomes fully developed so as to form relatively ideal plastic hinges. With the increase in the reinforcement ratio, the moment-carrying capacity of the composite beams improves significantly, but the ductility of the beams and the rotation ability of the plastic hinges decrease. The formulae for calculating the limit bending capacity in the negative moment area of outer-plated steel-concrete composite beams are proposed based on the test data. The calculated results agree well with the test results.
基金The Special Project of the Ministry of Construction ofChina (No.20060909).
文摘In order to establish the relationship between the measured dynamic response and the health status of long-span bridges, a double-layer model updating method for steel-concrete composite beam cable-stayed bridges is proposed. Measured frequencies are selected as the first-layer reference data, and the mass of the bridge deck, the grid density, the modulus of concrete and the ballast on the side span are modified by using a manual tuning technique. Measured global positioning system （GPS） data is selected as the second-layer reference data, and the degradation of the integral structure stiffness EI of the whole bridge is taken into account for the second-layer model updating by using the finite element iteration algorithm. The Nanpu Bridge in Shanghai is taken as a case to verify the applicability of the proposed model updating method. After the first-layer model updating, the standard deviation of modal frequencies is smaller than 7%. After the second-layer model updating, the error of the deflection of the mid-span is smaller than 10%. The integral structure stiffness of the whole bridge decreases about 20%. The research results show a good agreement between the calculated response and the measured response.
基金The National Natural Science Foundation of China(No.51678141,51378112)the Open Fund from the National Engineering Laboratory for Technology of Geological Disaster Prevention in Land Transportation,Southwest Jiaotong University(No.SWJTUGGS-2014001)
文摘An accurate finite element （ FE） model was constructed to examine the hysteretic behavior of double-skin steel-concrete composite box （ DSCB） piers for further understanding the seismic performance of DSCB piers; where the local buckling behavior of steel tubes, the confinement of the in-filled concrete and the interface action between steel tube and in-filled concrete were considered. The accuracy of the proposed FE model was verified by the bidirectional cyclic loading test results. Based on the validated FE model, the effects of some key parameters, such as section width to steel thickness ratio, slenderness ratio, aspect ratio and axial load ratio on the hysteretic behavior of DSCB piers were investigated. Finally, the skeleton curve model of DSCB piers was proposed. The numerical simulation results reveal that the peak strength and elastic stiffness decrease with the increase of the section width to steel thickness ratio. Moreover, the increase of the slenderness ratio may result in a significant reduction in the peak strength and elastic stiffness while the ultimate displacement increases. The proposed skeleton curve model can be taken as a reference for seismic performance analyses of the DSCB piers.
基金supported by the National Natural Science Foundation of China(Nos.52304108,52274148)China University of Mining and Technology-Beijing Undergraduate Innovation Training Program(No.202515011).
文摘Joints are widely distributed structural defects in rock masses,and their geometric characteristics play a decisive role in the overall stability of rocks under complex stress conditions.To clarify the influence of joint geometry on the mechanical behavior of jointed rock under such conditions,this study investigated the mechanical properties and failure mechanisms of composite jointed rock specimens with varying joint roughness and joint dip angles.Three typical failure modes under triaxial loading were identified,and a mechanical analysis model incorporating joint roughness and dip angle was established.The failure mechanism was revealed,and a discrete element model was developed to analyze the micro-damage evolution process of the specimens.The results show that the mechanical parameters of the specimens exhibit pronounced anisotropy.Both the elastic modulus and peak strength reach their minimum values at a joint dip angle of 60°.Increasing joint roughness significantly reduces the degree of anisotropy and enhances the energy storage capacity of the specimens.A strong linear relationship is observed between the elastic strain energy and the peak deviatoric stress,confirming the applicability of the linear energy storage law in composite jointed rocks.Discrete element simulations revealed the evolution path and dominant types of microcracks between the joint and matrix.The joint dip angle governs the transition of dominant crack types from tensile to shear and then back to tensile.Increased joint roughness significantly suppresses damage localization along the joint and results in an approximately 20%increase in the proportion of shear microcracks within the matrix.These findings clarify the regulatory role of joint geometrical parameters in the damage evolution process.
基金financially supported by the National Natural Science Foundation of China(Nos.52275314 and 52075074).
文摘Ni/TiAl composite brazed joints could significantly reduce the aircraft’s weight.However,low interfacial adhesion,coarse and brittle-hard intermetallic compounds(IMCs)seriously limited the application of Ni/TiAl composite joints in the next generation of aerospace applications.So enhanced K4169/TiAl composite joints were investigated by vacuum brazed with(Ni_(53.33)Cr_(20)B_(16.67)Si_(10)/Zr_(25)Ti_(18.75)Ta_(12.5)Ni_(25)Cu_(18.75))composite filler metal(CFM)designed based on cluster-plus-glue-atom model.The shear strength of the joint reached 485 MPa,comparable to the 491 MPa of TiAl substrate.The flat and brittle-hard diffusion reaction layer between Zones I and II was eliminated,simultaneously generating CrB4 dispersion strengthening due to the CFM developed with the interfacial solid-liquid space-time hysteresis effect.In Zones II and III,IMCs all transformed into Niss(Cr,Fe)_([0–88]),Niss(Ti,Al)_([004]),and Niss(Zr,Si)_([11–2])of circular and oval shapes through isothermal solidification.Meanwhile,the residual stresses and hardness were distributed in reticulated cladding characteristics.Thereby,lattice distortion led to solid solution strengthening and increased plastic toughness through crack termination and bridging mechanisms,which inhibited dislocations from plugging and crack propagation.Various interfaces in ZoneⅣwere regulated into semi-and coherent interfaces.Ni3(Ti,Al)/(Ni,Ti,Al)and(Ni,Ti,Al)/AlNi_(2)Ti were composed of higher interfacial bonding energy(2.771 J/m^(2),2.547 J/m^(2))and Ni-Ni covalent bonds.Interfacial covalent bonding and large interfacial bonding energy coupling strengthened Zone IV.Consequently,cracks initiated at the(Ni,Ti,Al)[013]/Ti3Al_([010])and expanded rapidly into TiAl substrate.Therefore,applying this method to design CFMs and regulate the phase,grain morphology,and interface’s fine structure could provide new pathways for dissimilar hard-to-join metals.
基金Projects(51078355,50938008)supported by the National Natural Science Foundation of ChinaProject(094801020)supported by the Academic Scholarship for Doctoral Candidates of the Ministry of Education,China+1 种基金Project(CX2011B093)supported by the Doctoral Candidate Research Innovation Project of Hunan Province,ChinaProject(20117Q008)supported by the Central University Basic Scientific Research Business Expenses Special Fund of China
文摘Based on Hamilton principle,the governing differential equations and the corresponding boundary conditions of steel-concrete composite box girder with consideration of the shear lag effect meeting self equilibrated stress,shear deformation,slip,as well as rotational inertia were induced.Therefore,natural frequency equations were obtained for the boundary types,such as simple support,cantilever,continuous girder and fixed support at two ends.The ANSYS finite element solutions were compared with the analytical solutions by calculation examples and the validity of the proposed approach was verified,which also shows the correctness of longitudinal warping displacement functions.Some meaningful conclusions for engineering design were obtained.The decrease extent of each order natural frequency of the steel-concrete composite box-girder is great under action of the shear lag effect.The shear-lag effect of steel-concrete composite box girder increases when frequency order rises,and increases while span-width ratio decreases.The proposed approach provides theoretical basis for further research of free vibration characteristics of steel-concrete composite box-girder.
基金funded by the National Natural Science Foundation of China(52478138).
文摘The connection efficiency of composite pre-tightened multi-tooth joint is low because of uneven load distribution and single load transmission path.In this paper,based on the principle of bio-tooth(suture)structure,combining soft material with fractal,a composite pre-tightened multi-hierarchy tooth joint is proposed,and the bearing performance and failure process of the joint through experiments and finite element method under tensile load.First,the ultimate bearing capacity,load distribution ratio,and failure process of different hierarchies of teeth joints are studied through experiments.Then,the progressive damage models of different hierarchies of tooth joints are established,and experiments verify the validity of the finite element model.Finally,the effects of soft material and increasing tooth hierarchy on the failure process and bearing capacity of composite pre-tightened tooth joints are analyzed by the finite element method.The following conclusions can be drawn:(1)The embedding of soft materials changed the failure process of the joint.Increasing the tooth hierarchy can give the joint more load transfer paths,but the failure process of the joint is complicated.(2)Embedding soft materials and increasing the tooth hierarchy simultaneously can effectively improve the bearing capacity of composite pre-tightened tooth joints,which is 87.8%higher than that of traditional three-tooth joints.
基金Projects(51078355,50938008) supported by the National Natural Science Foundation of ChinaProject(094801020) supported by the Academic Scholarship for Doctoral Candidates of the Ministry of Education,China+1 种基金Project(CX2011B093) supported by the Doctoral Candidate Research Innovation Project of Hunan Province, ChinaProject(20117Q008) supported by the Central University Basic Scientific Research Business Expenses Special Fund of China
文摘Based on the consideration of longitudinal warp caused by shear lag effects on concrete slabs and bottom plates of steel beams,shear deformation of steel beams and interface slip between steel beams and concrete slabs,the governing differential equations and boundary conditions of the steel-concrete composite box beams under lateral loading were derived using energy-variational method.The closed-form solutions for stress,deflection and slip of box beams under lateral loading were obtained,and the comparison of the analytical results and the experimental results for steel-concrete composite box beams under concentrated loading or uniform loading verifies the closed-form solution.The investigation of the parameters of load effects on composite box beams shows that:1) Slip stiffness has considerable impact on mid-span deflection and end slip when it is comparatively small;the mid-span deflection and end slip decrease significantly with the increase of slip stiffness,but when the slip stiffness reaches a certain value,its impact on mid-span deflection and end slip decreases to be negligible.2) The shear deformation has certain influence on mid-span deflection,and the larger the load is,the greater the influence is.3) The impact of shear deformation on end slip can be neglected.4) The strain of bottom plate of steel beam decreases with the increase of slip stiffness,while the shear lag effect becomes more significant.
基金supported by National Natural Science Foundation of China(Grant No.203S20230001),awarded to Wei-min Long。
文摘6061 aluminum alloy was successfully vacuum brazed to 304 stainless steel using Al-Si-Ge/Cu composite filler metal.The thermodynamic model was established to analyze the formation mechanism of microstructure in brazed joint and element diffusion behavior between filler metal and substrate.The findings indicated that the microstructure of 6061 aluminum alloy/304 stainless steel joint was a multilayer structure composed of three zones(ZoneⅠ,ZoneⅡand ZoneⅢ).The free energy(△G)calculation results indicated that Al-Si-M(M was Fe,Cr,Ni and Cu)ternary intermetallic compounds(IMCs)formed,when on M-Al side and M-Si/Ge side was similar.And only Al-M binary IMCs would be generated when there was large difference between on M-Al side and that on M-Si/Ge side.The calculation results of chemical potential of Si△_(μSi)and Ge△_(μGe)indicated that there was continuous Si and Ge diffusion toward Zone I,forming(Ge,Si)layer.The segregation of Si and Ge hindered the diffusion of Cr toward Zone II and promoted its diffusion toward(Ge,Si)layer,leading to an upward trend of Cr distribution in Al7(Fe,Cr)2Si layer.Negative△_(μNi)and△_(μFe)were responsible for continuous diffusion of Fe and Ni toward Zone II.The small difference between△_(μcu)in Zone I and Zone II contributed to distribution of CuAl2 in Zone II.The formation mechanism of joint could be mainly divided into four steps.
基金Project(12K104)supported by Scientific Research Fund of Hunan Provincial Education DepartmentChina+1 种基金Project(E51254)supported by Scientific Research Foundation for the Doctoral Program of Hunan University of Science and TechnologyChina
文摘Steel-concrete composite frames are seeing increased use in earthquake region because of their excellent structural characteristics, including high strength, stiffness, and good ductility. However, there exist gaps in the knowledge of seismic behavior and the design provisions for these structures. In order to better understand the seismic behaviors of composite frame systems, eight steel-concrete composite frames were designed. These composite frames were composed of steel-concrete composite beams and concrete filled steel tube columns. The axial compression ratio of column, slenderness ratio and linear stiffness ratio of beam to column were selected as main design parameters. The low reversed cyclic loading tests of composite frame system were carried out. Based on test results, the seismic behaviors of composite frames such as failure mode, hysteresis curve, strength degradation, rigidity degradation, ductility and energy dissipation were studied. Known from the test phenomenon, the main cause of damage is the out-of-plane deformation of steel beam and the yielding destruction of column heel. The hysteretic loops of composite frame appear a spindle shape and no obvious pinch phenomenon. The results demonstrate that this type of composite frame has favorable seismic behaviors. Furthermore, the effects of design parameters on seismic behaviors were also discussed. The results of the experiment show that the different design parameter has different influence rule on seismic behaviors of composite frame.
文摘Adopting a steel-anchor beam and steel corbel composite structure in the anchor zone on pylon is one of the key techniques for the design of Jintang bridge, a cable-stayed bridge in Zhoushan, China. In order to ensure the safety of the steel-concrete composite structure, a stud connector model for the joint section was put forward. Experiments were conducted to obtain the relation between load and slip of specimen, the failure pattern of stud connector, the yield bearing capacity and ultimate bearing capacity of a single stud, etc. The whole process of the structural behavior of the specimen was comprehensively analyzed. The features of the internal force distribution in the steel-concrete composite structure and the strain distribution of stud connector under different loads were emphatically studied. The test results show that the stud connector is applicable for the steel-concrete composite structure for pylon of Jintang bridge. The stud has a good ductility performance and a obvious yield process before its destruction. The stud connector basically works in a state of elasticity under a load less than the yield load.
文摘Proposes a simplified finite element model for steel-concrete composite beams. The effects of slip can be taken into account by creating a special matrix of shear connector stiffness and using the iteration method. Meanwhile, the effect of material non-linearity of steel and concrete on rigidity and strength of composite beams is considered. With the age-adjusted effective modulus method, the analysis for the whole process of shrinkage and creep under long-term load can be performed. The ultimate load, deflection, stress and slip of continuous composite beams under short-term and long-term load are computed using the proposed finite element model. The numerical results are compared with the experimental results and existing values based on other numerical methods, and are found to be in good agreement.
基金Project(50708112) supported by the National Natural Science Foundation of ChinaProject(IRT1296) supported by the Program for Changjiang Scholars and Innovative Research Team in University
文摘Slip of a composite box beam may reduce its stiffness, enlarge its deformation and affect its performance. In this work, the governing differential equations and boundary conditions of composite box beams were established. Analytic solutions of combined differential equations were also established. Partial degree of freedom was adopted to establish a new FEA element of three-dimensional beam, taking into account the slip effect. Slip and its first-order derivative were introduced into the nodes of composite box beams as generalized degree of freedom. Stiffness matrix and load array of beam elements were established. A three-dimensional nonlinear calculation program was worked out. The results show that the element is reliable and easy to divide and is suitable for special nonlinear analysis of large-span composite box beams.
基金Project(2011BAJ09B02)supported by the National Key Technology R&D Program,ChinaProjects(51578548,51378511,51678576)supported by the National Natural Science Foundation of China
文摘This work experimentally investigates the effects of shear stud characteristics on the interface slippage of steel-concrete composite push-out specimens. ABAQUS is used to establish a detailed 3D finite element(FE) model and analyze the behavior of push-out specimens. The modeling results are in good agreement with the experimental results. Based on parametrical analysis using the validated FE approaches, the effects of important design parameters, such as the diameter, number, length to diameter ratio, and yield strength of studs, concrete strength and steel transverse reinforcement ratio, on the load-slip relationship at the interface of composite beams are discussed. In addition, a simplified approach to model studs is developed using virtual springs with an equivalent stiffness. This approach is demonstrated to be able to predict the load-displacement response and ultimate bearing capacity of steel-concrete composite beams. The predicted results show satisfactory agreement with experimental results from the literature.
文摘To improve the quality of the steel-concrete composite segment of the box girder,to ensure the compactness of concrete to avoid debonding and to enhance the fatigue strength of concrete are critical to the concrete preparation for such site. Furthermore,the coordination ability to deformation between steel and concrete is also important because of great difference of the elastic modulus between them. Concrete for the steel-concrete composite segment with high fluidity,excellent crack resistance and low shrinkage was prepared by adding efficient poly-carboxylic water-reducing agent,high quality fly ash and expansion agent to it. The quality of the concrete of the half partial testing block showed that the optimal mix proportion of polypropylene fiber reinforced concrete had achieved expected effect,ensured high quality,thus meeting the requirements of construction.
