Actuator faults can be critical in turbofan engines as they can lead to stall,surge,loss of thrust and failure of speed control.Thus,fault diagnosis of gas turbine actuators has attracted considerable attention,from b...Actuator faults can be critical in turbofan engines as they can lead to stall,surge,loss of thrust and failure of speed control.Thus,fault diagnosis of gas turbine actuators has attracted considerable attention,from both academia and industry.However,the extensive literature that exists on this topic does not address identifying the severity of actuator faults and focuses mainly on actuator fault detection and isolation.In addition,previous studies of actuator fault identification have not dealt with multiple concurrent faults in real time,especially when these are accompanied by sudden failures under dynamic conditions.This study develops component-level models for fault identification in four typical actuators used in high-bypass ratio turbofan engines under both dynamic and steady-state conditions and these are then integrated with the engine performance model developed by the authors.The research results reported here present a novel method of quantifying actuator faults using dynamic effect compensation.The maximum error for each actuator is less than0.06%and 0.07%,with average computational time of less than 0.0058 s and 0.0086 s for steady-state and transient cases,respectively.These results confirm that the proposed method can accurately and efficiently identify concurrent actuator fault for an engine operating under either transient or steady-state conditions,even in the case of a sudden malfunction.The research results emonstrate the potential benefit to emergency response capabilities by introducing this method of monitoring the health of aero engines.展开更多
The present work aims to stabilize the room temperature allotropic transition of ammonium nitrate(AN)particles utilizing a microencapsulation technique,which involves solvent/non-solvent in which nitrocellulose(NC)has...The present work aims to stabilize the room temperature allotropic transition of ammonium nitrate(AN)particles utilizing a microencapsulation technique,which involves solvent/non-solvent in which nitrocellulose(NC)has been employed as a coating agent.The SEM micrographs revealed distinct features of both pure AN and NC,contrasting with the irregular granular surface topography of the coated AN particles,demonstrating the adherence of NC on the AN surface.Structural analysis via infrared spectroscopy(IR)demonstrated a successful association of AN and NC,with slight shifts observed in IR bands indicating interfacial interactions.Powder X-ray Diffraction(PXRD)analysis further elucidated the structural changes induced by the coating process,revealing that the NC coating altered the crystallization pattern of its pure form.Thermal analysis demonstrates distinct profiles for pure and coated AN,for which the coated sample exhibits a temperature increase and an enthalpy decrease of the room temperature allotropic transition by 6℃,and 36%,respectively.Furthermore,the presence of NC coating alters the intermolecular forces within the composite system,leading to a reduction in melting enthalpy of coated AN by~39%compared to pure AN.The thermal decomposition analysis shows a two-step thermolysis process for coated AN,with a significant increase in the released heat by about 78%accompanied by an increase in the activation barrier of NC and AN thermolysis,demonstrating a stabilized reactivity of the AN-NC particles.These findings highlight the synergistic effect of NC coating on AN particles,which contributed to a structural and reactive stabilization of both AN and NC,proving the potential application of NC-coated AN as a strategically advantageous oxidizer in composite solid propellant formulations.展开更多
Weathering steel exhibits excellent corrosion resistance and is widely used in bridges,towers,railways,highways,and other engineering projects that are exposed to the atmosphere for long periods of time.However,before...Weathering steel exhibits excellent corrosion resistance and is widely used in bridges,towers,railways,highways,and other engineering projects that are exposed to the atmosphere for long periods of time.However,before the formation of stable rust layers,weathering steel is prone to liquid rust sagging and spattering,leading to environmental pollution and city appearance concerns.These factors limit the application and development of weathering steel.In this study,a rapid and environmentally friendly method was de-veloped by introducing alloying elements,specifically investigating the role of Sn in the rapid stabilization of rust layers in marine atmo-spheric environments.The rust layer formed on weathering low-alloy steel exposed to prolonged outdoor conditions and laboratory im-mersion experiments was explored using electron probe micro-analyzer(EPMA),micro-Raman,X-ray photoelectron spectroscopy(XPS),and electrochemical measurements.Results showed an optimal synergistic effect between Sn and Cr,which facilitated the accelerated densification of the rust layer.This beneficial effect enhanced the capability of the rust layer to resist Cl^(-)erosion and improved the protec-tion performance of the rust layer.展开更多
Although perovskite solar cells(PSCs) demonstrate outstanding power conversion efficiency(PCE), their practical applications are still limited by stability issues caused by various problems such as poor crystal qualit...Although perovskite solar cells(PSCs) demonstrate outstanding power conversion efficiency(PCE), their practical applications are still limited by stability issues caused by various problems such as poor crystal quality triggered structural instability. Herein, to address the structural instability of perovskites, we introduced a polymer additive, poly-L-lysine hydrobromide(PLL), into the perovskite precursor to promote perovskite crystal growth, thereby constructing a stable crystal structure. The results show that the introduction of PLL modulates the colloidal aggregation state in the precursor solution, provides longer time for growth of perovskite and successfully realizes the formation of large-sized perovskite films with high crystallinity. More importantly, owing to its hydrophobic long-chain structure and the widespread distribution of C=O and NH on the chain, PLL firmly locks the perovskite crystals, enhancing their structural stability while blocking the intrusion of external factors such as water molecules, significantly enhances the overall stability of the device. The results show that the PLL-based PSC has negligible hysteresis and its PCE is improved from 22.20% to 23.66%. while the PLL-modified perovskite films and devices demonstrate excellent thermal and environmental stability. These findings highlight PLL as a promising additive for optimizing perovskite crystallization, offering guidance for fabricating efficient and stable photovoltaic devices.展开更多
Objectives:Cold-acclimated organisms accumulate low molecular weight organic solutes such as sugar alcohols and soluble sugars.This study aimed to compare the efficacy of five sugar alcohols and 14 soluble sugars in s...Objectives:Cold-acclimated organisms accumulate low molecular weight organic solutes such as sugar alcohols and soluble sugars.This study aimed to compare the efficacy of five sugar alcohols and 14 soluble sugars in stabilizing proteins under freezing,freeze-drying,and air-drying stresses.Materials and methods:Glucose-6-Phosphate Dehydrogenase(G6PD)was used as the model protein.G6PD solutions with or without sugar alcohols and or sugars were subjected to freezing,freeze-drying,and air-drying stresses.The recovery of G6PD activity was measured to evaluate the protective efficacy of these compounds.Results:Without stabilizers,freezing G6PD at-20℃ or-80℃ reduced enzyme activity by around 24%,while freeze-drying or air-drying reduced activity by 90%-95%.Among the five sugar alcohols tested,pinitol,quebrachitol and sorbitol stabilized G6PD,whereas mannitol and myo-inositol destabilized it.Among 14 soluble sugars,trehalose and raffinose showed slightly lower enzyme recovery after repeated freeze-thaw cycles at-20℃.Most soluble sugars(except arabinose and xylose)protected G6PD during freeze-drying,with di-,tri-,and oligosaccharides generally outperforming monosaccharides.During air-drying,lactose was ineffective,while arabinose,galactose,and xylose were detrimental.Conclusion:The study highlights the diverse mechanisms of sugar alcohols and sugars in protein stabilization under stress,offering insights for formulating stable protein-and cell-based drugs.展开更多
This study investigates the innovative reuse of sewage sludge with eco-friendly alkaline solutes to improve clayey soil without conventional cementitious binders.The unconfined compressive strength(UCS)was the main cr...This study investigates the innovative reuse of sewage sludge with eco-friendly alkaline solutes to improve clayey soil without conventional cementitious binders.The unconfined compressive strength(UCS)was the main criterion to assess the quality and effectiveness of the proposed solutions,as this test was performed to measure the strength of the stabilized clay by varying binders’dosages and curing times.Moreover,the direct shear test(DST)was used to investigate the Mohr-Coulomb parameters of the treated soil.Microstructure observations of the natural and treated soil were conducted using scanning electron microscope(SEM),energy-dispersive spectroscopy(EDS),and FTIR.Furthermore,toxicity characteristic leaching procedure(TCLP)tests were performed on the treated soil to investigate the leachability of metals.According to the results,using 2.5%of sewage sludge activated by NaOH and Na_(2)SiO_(3)increases the UCS values from 176 kPa to 1.46 MPa after 7 d and 56 d of curing,respectively.The results of the DST indicate that sewage sludge as a precursor increases cohesion and enhances frictional resistance,thereby improving the Mohr-Coulomb parameters of the stabilized soil.The SEM micrographs show that alkali-activated sewage sludge increases the integrity and reduces the cavity volumes in the stabilized soil.Moreover,TCLP tests revealed that the solubility of metals in the treated soil alkaliactivated by sewage sludge significantly decreased.This study suggests that using sewage sludge can replace cement and lime in ground improvement,improve the circular economy,and reduce the carbon footprint of construction projects.展开更多
The steady-state transverse vibration of an axially moving string with geometric nonlinearity was investigated. The transport speed was assumed to be a constant mean speed with small harmonic variations. The nonlinear...The steady-state transverse vibration of an axially moving string with geometric nonlinearity was investigated. The transport speed was assumed to be a constant mean speed with small harmonic variations. The nonlinear partial-differential equation that governs the transverse vibration of the string was derived by use of the Hamilton principle. The method of multiple scales was applied directly to the equation. The solvability condition of eliminating the secular terms was established. Closed form solutions for the amplitude and the existence conditions of nontrivial steady-state response of the two-to-one parametric resonance were obtained. Some numerical examples showing effects of the mean transport speed, the amplitude and the frequency of speed variation were presented. The Liapunov linearized stability theory was employed to derive the instability conditions of the trivial solution and the nontrivial solutions for the two-to-one parametric resonance. Some numerical examples highlighting influences of the related parameters on the instability conditions were presented.展开更多
The effects of plasma screening on the ^(1)P^(o) resonance states of H-and He below the n=3 and n=4 thresholds of the respective subsystemsare investigated using the stabilization method and correlated exponential wav...The effects of plasma screening on the ^(1)P^(o) resonance states of H-and He below the n=3 and n=4 thresholds of the respective subsystemsare investigated using the stabilization method and correlated exponential wave functions.Two plasma mediums,namely,the Debye plasma and quantum plasma environments are considered.The screened Coulomb potential(SCP)obtained from Debye-Hückel model is used to represent Debye plasma environments and the exponential cosine screened Coulomb potential(ECSCP)obtained from a modified Debye-Hückel model is used to represent quantum plasma environments.The resonance parameters(resonance positions and widths)are presented in terms of the screening parameters.展开更多
Dear Editor,This letter is concerned with stability analysis and stabilization design for sampled-data based load frequency control(LFC) systems via a data-driven method. By describing the dynamic behavior of LFC syst...Dear Editor,This letter is concerned with stability analysis and stabilization design for sampled-data based load frequency control(LFC) systems via a data-driven method. By describing the dynamic behavior of LFC systems based on a data-based representation, a stability criterion is derived to obtain the admissible maximum sampling interval(MSI) for a given controller and a design condition of the PI-type controller is further developed to meet the required MSI. Finally, the effectiveness of the proposed methods is verified by a case study.展开更多
In the paper the simplified criterion of a steady-state stability of electric power systems (EPS) is justified on the basis of Lyapunov functions in a quadratic form ensuring necessary and sufficient conditions of its...In the paper the simplified criterion of a steady-state stability of electric power systems (EPS) is justified on the basis of Lyapunov functions in a quadratic form ensuring necessary and sufficient conditions of its performance. Upon that, the use of the node-voltage equations allows reducing study of a steady-state stability of complex EPS to study of the generator-bus system. The obtained results facilitate studies of a steady-state stability of the complex systems and have practical importance.展开更多
Slow-release phosphate materials were prepared by activating insoluble phosphate with organic acid to stabilize high concentrations of Cd and Zn in contaminated smelter soil.The results showed that oxalic acid(0.1 mol...Slow-release phosphate materials were prepared by activating insoluble phosphate with organic acid to stabilize high concentrations of Cd and Zn in contaminated smelter soil.The results showed that oxalic acid(0.1 mol/L)activated tricalcium phosphate(TO-0.1)provided the most efficient stabilization of Cd and Zn.After 30 d treatment,leaching concentrations of Cd and Zn in soil were decreased from 3.17 and 16.60 mg/L to 0.078 and 0.32 mg/L,respectively.The acid-soluble fractions of Cd and Zn were transformed into reducible,oxidizable,and residual fractions.Notably,As mobility in TO-0.1 treated soils did not increase.In addition,acid rain leaching and 150 d of natural aging revealed that the slow-release phosphate material provided long-term stability for the stabilization of Cd and Zn.This study verifies the potential application of slow-release phosphate materials for the remediation of heavy metal contaminated soil at smelting sites.展开更多
Wellbore instability is one of the significant challenges in the drilling engineering and during the development of carbonate reservoirs,especially with open-hole completion.The problems of wellbore instability such a...Wellbore instability is one of the significant challenges in the drilling engineering and during the development of carbonate reservoirs,especially with open-hole completion.The problems of wellbore instability such as downhole collapse and silt deposit in the fractured carbonate reservoir of Tarim Basin(Ordovician)are severe.Solid destabilization and production(SDP)was proposed to describe this engineering problem of carbonate reservoirs.To clarify the mechanism and mitigate potential borehole instability problems,we conducted particle size distribution(PSD)analysis,X-ray diffraction(XRD)analysis,triaxial compression tests,and micro-scale sand production tests based on data analysis.We found that the rock fragments and silt in the wellbore came from two sources:one from the wellbore collapse in the upper unplugged layers and the other from the production of sand particles carried by the fluid in the productive layers.Based on the experimental study,a novel method combining a geomechanical model and microscopic sand production model was proposed to predict wellbore instability and analyze its influencing factors.The critical condition and failure zone predicted by the prediction model fit well with the field observations.According to the prediction results,the management and prevention measures of wellbore instability in carbonate reservoirs were proposed.It is suggested to optimize the well track in new drilling wells while upgrading the production system in old wells.This study is of great guiding significance for the optimization of carbonate solid control and it improves the understanding of the sand production problems in carbonate reservoirs.展开更多
This study presents a novel approach to enhance silicon anode performance through barium titanate(BTO)incorporation,with the establishment of a force-electric coupling model.By introducing piezoelectric BTO into silic...This study presents a novel approach to enhance silicon anode performance through barium titanate(BTO)incorporation,with the establishment of a force-electric coupling model.By introducing piezoelectric BTO into silicon matrices,we successfully improved both the mechanical stability and electrochemical kinetics of the anode.The developed force-electric coupling model explains how BTO mitigates stress accumulation during lithiation while optimizing the kinetics of Li^(+)and electron transfer.Experimental verification and multiphysical simulation indicate that Si@BTO effectively eliminates structural degradation during the cycling process and significantly reduces the charge transfer resistance.The force-electric coupling mechanism further facilitates stable solid electrolyte interphase(SEI)formation.When paired with LiFePO_(4)cathodes,Si@BTO maintains 76% capacity retention after 500 cycles at a 10 C rate.This work establishes a basic force-electric coupling model framework and offers insights into the development of advanced silicon anode batteries with exceptional performance.展开更多
This paper deals with the singular chemotaxis-Navier-Stokes system with indirect signal consumption n_(t)+u·▽v=△n-Х▽·(n/v▽u);v_(t)+u·▽v=△v-uw;w_(t)+u·▽w=△w-w+n;u_(t)+(u·▽)u=△u-▽P+...This paper deals with the singular chemotaxis-Navier-Stokes system with indirect signal consumption n_(t)+u·▽v=△n-Х▽·(n/v▽u);v_(t)+u·▽v=△v-uw;w_(t)+u·▽w=△w-w+n;u_(t)+(u·▽)u=△u-▽P+n▽Ф;▽·u=0,x∈Ω,t>0 in a bounded and smooth domainΩ⊂ℝ2 with no-flux/no-flux/no-flux/no-slip boundary conditions,whereΦ∈W2,∞(Ω).A recent literature[Dai F,Liu B.J Differential Equations,2023,369:115–155]has proved that for all reasonably regular initial data,the associated initial-boundary value problem possesses a global classical solution,but qualitative information on the behavior of solution has never been touched so far.In stark contrast to the positive effect of indirect signal consumption mechanism on the global solvability of system,the analysis of asymptotic behavior of solution to the system with indirect signal consumption is essentially complicated than that with direct signal consumption because the favorable coupled structure between cells and signal is broken down by the indirect signal consumption mechanism.The present study shows that the global classical solution exponentially stabilizes toward the corresponding spatially homogeneous equilibria under a smallness condition on the initial cell mass.In comparison to the previously known result concerning the uniform convergence of solution to the system with direct signal consumption,our result inter alia provides a more in-depth understanding on the asymptotic behavior of solution.展开更多
We propose an adaptive stencil construction for high-order accurate finite volume schemes a posteriori stabilized devoted to solve one-dimensional steady-state hyperbolic equations.High accuracy(up to the sixth-order ...We propose an adaptive stencil construction for high-order accurate finite volume schemes a posteriori stabilized devoted to solve one-dimensional steady-state hyperbolic equations.High accuracy(up to the sixth-order presently)is achieved,thanks to polynomial recon-structions while stability is provided with an a posteriori MOOD method which controls the cell polynomial degree for eliminating non-physical oscillations in the vicinity of dis-continuities.We supplemented this scheme with a stencil construction allowing to reduce even further the numerical dissipation.The stencil is shifted away from troubles(shocks,discontinuities,etc.)leading to less oscillating polynomial reconstructions.Experimented on linear,Burgers',and Euler equations,we demonstrate that the adaptive stencil technique manages to retrieve smooth solutions with optimal order of accuracy but also irregular ones without spurious oscillations.Moreover,we numerically show that the approach allows to reduce the dissipation still maintaining the essentially non-oscillatory behavior.展开更多
We read with great interest the investigations conducted by Pourakbar et al.(2024)on the“Stabilization of clay soil using alkali-activated sewage sludge.”The authors have investigated the feasibility of utilizing al...We read with great interest the investigations conducted by Pourakbar et al.(2024)on the“Stabilization of clay soil using alkali-activated sewage sludge.”The authors have investigated the feasibility of utilizing alkali-activated sewage sludge(AASS)as a binder for stabilizing the clayey soil.Sewage sludge(SS)in varying proportions of 1.5%,2%,2.5%,3.5%,and 4.5%was utilized to prepare geopolymer binders using sodium and potassium-based alkali activators.Furthermore,unconfined compressive strength(UCS)and direct shear tests were conducted to examine the strength development of clayey soil stabilized with AASS.While the study presented some intriguing results,we have identified critical concerns regarding(i)the selection of SS as a precursor for alkali activation,(ii)technical inconsistencies associated with the compaction characteristics and microstructural analysis,and(iii)the feasibility of the proposed methodology for practical applications.Through our discussion,we seek to highlight these issues and provide constructive feedback to advance the understanding of alkali activation processes and their implications for soil stabilization.展开更多
This study presents a numerical analysis of the steady-state solution for transient magnetohydrodynamic(MHD)dissipative and radiative fluid flow,incorporating an inducedmagnetic field(IMF)and considering a relatively ...This study presents a numerical analysis of the steady-state solution for transient magnetohydrodynamic(MHD)dissipative and radiative fluid flow,incorporating an inducedmagnetic field(IMF)and considering a relatively high concentration of foreign mass(accounting for Soret and Dufour effects)over a vertically oriented semi-infinite plate.The governing equations were normalized using boundary layer(BL)approximations.The resulting nonlinear system of partial differential equations(PDEs)was discretized and solved using an efficient explicit finite difference method(FDM).Numerical simulations were conducted using MATLAB R2015a,and the developed numerical code was verified through comparison with another code written in FORTRAN 6.6a.To ensure the reliability of the results,both mesh refinement and steady-state time validation tests were performed.Furthermore,a comparison with existing published studies was made to confirm the accuracy of the findings.The dimensionless equations revealed the impacts of several key parameters.The IMF initially intensifies near the plate before gradually diminishing as the magnetic parameter increases.For the range 0≤y≤1.8(where y is the horizontal direction),the IMF decreases with a rise in the magnetic Prandtl number;however,for 1.8≤y≤7(approximately),the magnetic field begins to increase.Beyond this,the profile of the magnetic field becomes somewhat irregular through the remaining part of the BL.展开更多
This paper proposes a model-based control framework for vehicle platooning systems with secondorder nonlinear dynamics operating over switching signed networks,time-varying delays,and deception attacks.The study inclu...This paper proposes a model-based control framework for vehicle platooning systems with secondorder nonlinear dynamics operating over switching signed networks,time-varying delays,and deception attacks.The study includes two configurations:a leaderless structure using Finite-Time Non-Singular Terminal Bipartite Consensus(FNTBC)and Fixed-Time Bipartite Consensus(FXTBC),and a leader—follower structure ensuring structural balance and robustness against deceptive signals.In the leaderless model,a bipartite controller based on impulsive control theory,gauge transformation,and Markovian switching Lyapunov functions ensures mean-square stability and coordination under deception attacks and communication delays.The FNTBC achieves finite-time convergence depending on initial conditions,while the FXTBC guarantees fixed-time convergence independent of them,providing adaptability to different operating states.In the leader—follower case,a discontinuous impulsive control law synchronizes all followers with the leader despite deceptive attacks and switching topologies,maintaining robust coordination through nonlinear corrective mechanisms.To validate the approach,simulations are conducted on systems of five and seventeen vehicles in both leaderless and leader—follower configurations.The results demonstrate that the proposed framework achieves rapid consensus,strong robustness,and high resistance to deception attacks,offering a secure and scalable model-based control solution for modern vehicular communication networks.展开更多
In order to enhance the dynamic control precision of inertial stabilization platform(ISP),a disturbance sliding mode observer(DSMO)is proposed in this paper suppressing disturbance torques inherent within the system.T...In order to enhance the dynamic control precision of inertial stabilization platform(ISP),a disturbance sliding mode observer(DSMO)is proposed in this paper suppressing disturbance torques inherent within the system.The control accuracy of ISP is fundamentally circumscribed by various disturbance torques in rotating shaft.Therefore,a dynamic model of ISP incorporating composite perturbations is established with regard to the stabilization of axis in the inertial reference frame.Subsequently,an online estimator for control loop uncertainties based on the sliding mode control algorithm is designed to estimate the aggregate disturbances of various parameters uncertainties and other unmodeled disturbances that cannot be accurately calibrated.Finally,the proposed DSMO is integrated into a classical proportional-integral-derivative(PID)control scheme,utilizing feedforward approach to compensate the composite disturbance in the control loop online.The effectiveness of the proposed disturbance observer is validated through simulation and hardware experimentation,demonstrating a significant improvement in the dynamic control performance and robustness of the classical PID controller extensively utilized in the field of engineering.展开更多
基金support by the National Natural Science Foundation of China(Grant No.52402520)。
文摘Actuator faults can be critical in turbofan engines as they can lead to stall,surge,loss of thrust and failure of speed control.Thus,fault diagnosis of gas turbine actuators has attracted considerable attention,from both academia and industry.However,the extensive literature that exists on this topic does not address identifying the severity of actuator faults and focuses mainly on actuator fault detection and isolation.In addition,previous studies of actuator fault identification have not dealt with multiple concurrent faults in real time,especially when these are accompanied by sudden failures under dynamic conditions.This study develops component-level models for fault identification in four typical actuators used in high-bypass ratio turbofan engines under both dynamic and steady-state conditions and these are then integrated with the engine performance model developed by the authors.The research results reported here present a novel method of quantifying actuator faults using dynamic effect compensation.The maximum error for each actuator is less than0.06%and 0.07%,with average computational time of less than 0.0058 s and 0.0086 s for steady-state and transient cases,respectively.These results confirm that the proposed method can accurately and efficiently identify concurrent actuator fault for an engine operating under either transient or steady-state conditions,even in the case of a sudden malfunction.The research results emonstrate the potential benefit to emergency response capabilities by introducing this method of monitoring the health of aero engines.
文摘The present work aims to stabilize the room temperature allotropic transition of ammonium nitrate(AN)particles utilizing a microencapsulation technique,which involves solvent/non-solvent in which nitrocellulose(NC)has been employed as a coating agent.The SEM micrographs revealed distinct features of both pure AN and NC,contrasting with the irregular granular surface topography of the coated AN particles,demonstrating the adherence of NC on the AN surface.Structural analysis via infrared spectroscopy(IR)demonstrated a successful association of AN and NC,with slight shifts observed in IR bands indicating interfacial interactions.Powder X-ray Diffraction(PXRD)analysis further elucidated the structural changes induced by the coating process,revealing that the NC coating altered the crystallization pattern of its pure form.Thermal analysis demonstrates distinct profiles for pure and coated AN,for which the coated sample exhibits a temperature increase and an enthalpy decrease of the room temperature allotropic transition by 6℃,and 36%,respectively.Furthermore,the presence of NC coating alters the intermolecular forces within the composite system,leading to a reduction in melting enthalpy of coated AN by~39%compared to pure AN.The thermal decomposition analysis shows a two-step thermolysis process for coated AN,with a significant increase in the released heat by about 78%accompanied by an increase in the activation barrier of NC and AN thermolysis,demonstrating a stabilized reactivity of the AN-NC particles.These findings highlight the synergistic effect of NC coating on AN particles,which contributed to a structural and reactive stabilization of both AN and NC,proving the potential application of NC-coated AN as a strategically advantageous oxidizer in composite solid propellant formulations.
基金support of the National Natural Science Foundation of China(No.52171063).
文摘Weathering steel exhibits excellent corrosion resistance and is widely used in bridges,towers,railways,highways,and other engineering projects that are exposed to the atmosphere for long periods of time.However,before the formation of stable rust layers,weathering steel is prone to liquid rust sagging and spattering,leading to environmental pollution and city appearance concerns.These factors limit the application and development of weathering steel.In this study,a rapid and environmentally friendly method was de-veloped by introducing alloying elements,specifically investigating the role of Sn in the rapid stabilization of rust layers in marine atmo-spheric environments.The rust layer formed on weathering low-alloy steel exposed to prolonged outdoor conditions and laboratory im-mersion experiments was explored using electron probe micro-analyzer(EPMA),micro-Raman,X-ray photoelectron spectroscopy(XPS),and electrochemical measurements.Results showed an optimal synergistic effect between Sn and Cr,which facilitated the accelerated densification of the rust layer.This beneficial effect enhanced the capability of the rust layer to resist Cl^(-)erosion and improved the protec-tion performance of the rust layer.
基金the financial support from the National Key R&D Program of China (No. 2021YFB3800102)the National Natural Science Foundation of China (Nos. 52102196 and 52302324)CASHIPS Director's Fund (Nos. YZJJ-GGZX-2022-01 and YZJJ202304-CX)。
文摘Although perovskite solar cells(PSCs) demonstrate outstanding power conversion efficiency(PCE), their practical applications are still limited by stability issues caused by various problems such as poor crystal quality triggered structural instability. Herein, to address the structural instability of perovskites, we introduced a polymer additive, poly-L-lysine hydrobromide(PLL), into the perovskite precursor to promote perovskite crystal growth, thereby constructing a stable crystal structure. The results show that the introduction of PLL modulates the colloidal aggregation state in the precursor solution, provides longer time for growth of perovskite and successfully realizes the formation of large-sized perovskite films with high crystallinity. More importantly, owing to its hydrophobic long-chain structure and the widespread distribution of C=O and NH on the chain, PLL firmly locks the perovskite crystals, enhancing their structural stability while blocking the intrusion of external factors such as water molecules, significantly enhances the overall stability of the device. The results show that the PLL-based PSC has negligible hysteresis and its PCE is improved from 22.20% to 23.66%. while the PLL-modified perovskite films and devices demonstrate excellent thermal and environmental stability. These findings highlight PLL as a promising additive for optimizing perovskite crystallization, offering guidance for fabricating efficient and stable photovoltaic devices.
基金supported by a research grant from the National University of Singapore to WQS(RP-3960366)a collaborative research grant from Sichuan Zhongke Organ Co.Ltd(Chengdu,China).
文摘Objectives:Cold-acclimated organisms accumulate low molecular weight organic solutes such as sugar alcohols and soluble sugars.This study aimed to compare the efficacy of five sugar alcohols and 14 soluble sugars in stabilizing proteins under freezing,freeze-drying,and air-drying stresses.Materials and methods:Glucose-6-Phosphate Dehydrogenase(G6PD)was used as the model protein.G6PD solutions with or without sugar alcohols and or sugars were subjected to freezing,freeze-drying,and air-drying stresses.The recovery of G6PD activity was measured to evaluate the protective efficacy of these compounds.Results:Without stabilizers,freezing G6PD at-20℃ or-80℃ reduced enzyme activity by around 24%,while freeze-drying or air-drying reduced activity by 90%-95%.Among the five sugar alcohols tested,pinitol,quebrachitol and sorbitol stabilized G6PD,whereas mannitol and myo-inositol destabilized it.Among 14 soluble sugars,trehalose and raffinose showed slightly lower enzyme recovery after repeated freeze-thaw cycles at-20℃.Most soluble sugars(except arabinose and xylose)protected G6PD during freeze-drying,with di-,tri-,and oligosaccharides generally outperforming monosaccharides.During air-drying,lactose was ineffective,while arabinose,galactose,and xylose were detrimental.Conclusion:The study highlights the diverse mechanisms of sugar alcohols and sugars in protein stabilization under stress,offering insights for formulating stable protein-and cell-based drugs.
文摘This study investigates the innovative reuse of sewage sludge with eco-friendly alkaline solutes to improve clayey soil without conventional cementitious binders.The unconfined compressive strength(UCS)was the main criterion to assess the quality and effectiveness of the proposed solutions,as this test was performed to measure the strength of the stabilized clay by varying binders’dosages and curing times.Moreover,the direct shear test(DST)was used to investigate the Mohr-Coulomb parameters of the treated soil.Microstructure observations of the natural and treated soil were conducted using scanning electron microscope(SEM),energy-dispersive spectroscopy(EDS),and FTIR.Furthermore,toxicity characteristic leaching procedure(TCLP)tests were performed on the treated soil to investigate the leachability of metals.According to the results,using 2.5%of sewage sludge activated by NaOH and Na_(2)SiO_(3)increases the UCS values from 176 kPa to 1.46 MPa after 7 d and 56 d of curing,respectively.The results of the DST indicate that sewage sludge as a precursor increases cohesion and enhances frictional resistance,thereby improving the Mohr-Coulomb parameters of the stabilized soil.The SEM micrographs show that alkali-activated sewage sludge increases the integrity and reduces the cavity volumes in the stabilized soil.Moreover,TCLP tests revealed that the solubility of metals in the treated soil alkaliactivated by sewage sludge significantly decreased.This study suggests that using sewage sludge can replace cement and lime in ground improvement,improve the circular economy,and reduce the carbon footprint of construction projects.
文摘The steady-state transverse vibration of an axially moving string with geometric nonlinearity was investigated. The transport speed was assumed to be a constant mean speed with small harmonic variations. The nonlinear partial-differential equation that governs the transverse vibration of the string was derived by use of the Hamilton principle. The method of multiple scales was applied directly to the equation. The solvability condition of eliminating the secular terms was established. Closed form solutions for the amplitude and the existence conditions of nontrivial steady-state response of the two-to-one parametric resonance were obtained. Some numerical examples showing effects of the mean transport speed, the amplitude and the frequency of speed variation were presented. The Liapunov linearized stability theory was employed to derive the instability conditions of the trivial solution and the nontrivial solutions for the two-to-one parametric resonance. Some numerical examples highlighting influences of the related parameters on the instability conditions were presented.
基金Supported by the Natural Science Foundation of Heilongjiang Province(LH2024A025)。
文摘The effects of plasma screening on the ^(1)P^(o) resonance states of H-and He below the n=3 and n=4 thresholds of the respective subsystemsare investigated using the stabilization method and correlated exponential wave functions.Two plasma mediums,namely,the Debye plasma and quantum plasma environments are considered.The screened Coulomb potential(SCP)obtained from Debye-Hückel model is used to represent Debye plasma environments and the exponential cosine screened Coulomb potential(ECSCP)obtained from a modified Debye-Hückel model is used to represent quantum plasma environments.The resonance parameters(resonance positions and widths)are presented in terms of the screening parameters.
基金supported in part by the National Natural Science Foundation of China(62373337,62373333)the 111 Project(B17040)State Key Laboratory of Advanced Electromagnetic Technology(2024KF002)
文摘Dear Editor,This letter is concerned with stability analysis and stabilization design for sampled-data based load frequency control(LFC) systems via a data-driven method. By describing the dynamic behavior of LFC systems based on a data-based representation, a stability criterion is derived to obtain the admissible maximum sampling interval(MSI) for a given controller and a design condition of the PI-type controller is further developed to meet the required MSI. Finally, the effectiveness of the proposed methods is verified by a case study.
文摘In the paper the simplified criterion of a steady-state stability of electric power systems (EPS) is justified on the basis of Lyapunov functions in a quadratic form ensuring necessary and sufficient conditions of its performance. Upon that, the use of the node-voltage equations allows reducing study of a steady-state stability of complex EPS to study of the generator-bus system. The obtained results facilitate studies of a steady-state stability of the complex systems and have practical importance.
基金supported by the Natural Science Foundation of Hunan Province,China(No.2024JJ1012)the Postgraduate Innovative Project of Central South University,China(No.2023ZZTS0459)the National Key Research and Development Program of China(No.2019YFC1803605)。
文摘Slow-release phosphate materials were prepared by activating insoluble phosphate with organic acid to stabilize high concentrations of Cd and Zn in contaminated smelter soil.The results showed that oxalic acid(0.1 mol/L)activated tricalcium phosphate(TO-0.1)provided the most efficient stabilization of Cd and Zn.After 30 d treatment,leaching concentrations of Cd and Zn in soil were decreased from 3.17 and 16.60 mg/L to 0.078 and 0.32 mg/L,respectively.The acid-soluble fractions of Cd and Zn were transformed into reducible,oxidizable,and residual fractions.Notably,As mobility in TO-0.1 treated soils did not increase.In addition,acid rain leaching and 150 d of natural aging revealed that the slow-release phosphate material provided long-term stability for the stabilization of Cd and Zn.This study verifies the potential application of slow-release phosphate materials for the remediation of heavy metal contaminated soil at smelting sites.
基金financially supported by the National Natural Science Foundation of China(Grant No.52074331).
文摘Wellbore instability is one of the significant challenges in the drilling engineering and during the development of carbonate reservoirs,especially with open-hole completion.The problems of wellbore instability such as downhole collapse and silt deposit in the fractured carbonate reservoir of Tarim Basin(Ordovician)are severe.Solid destabilization and production(SDP)was proposed to describe this engineering problem of carbonate reservoirs.To clarify the mechanism and mitigate potential borehole instability problems,we conducted particle size distribution(PSD)analysis,X-ray diffraction(XRD)analysis,triaxial compression tests,and micro-scale sand production tests based on data analysis.We found that the rock fragments and silt in the wellbore came from two sources:one from the wellbore collapse in the upper unplugged layers and the other from the production of sand particles carried by the fluid in the productive layers.Based on the experimental study,a novel method combining a geomechanical model and microscopic sand production model was proposed to predict wellbore instability and analyze its influencing factors.The critical condition and failure zone predicted by the prediction model fit well with the field observations.According to the prediction results,the management and prevention measures of wellbore instability in carbonate reservoirs were proposed.It is suggested to optimize the well track in new drilling wells while upgrading the production system in old wells.This study is of great guiding significance for the optimization of carbonate solid control and it improves the understanding of the sand production problems in carbonate reservoirs.
基金the financial support of the National Natural Science Foundation of China(NSFC,No.12074093)。
文摘This study presents a novel approach to enhance silicon anode performance through barium titanate(BTO)incorporation,with the establishment of a force-electric coupling model.By introducing piezoelectric BTO into silicon matrices,we successfully improved both the mechanical stability and electrochemical kinetics of the anode.The developed force-electric coupling model explains how BTO mitigates stress accumulation during lithiation while optimizing the kinetics of Li^(+)and electron transfer.Experimental verification and multiphysical simulation indicate that Si@BTO effectively eliminates structural degradation during the cycling process and significantly reduces the charge transfer resistance.The force-electric coupling mechanism further facilitates stable solid electrolyte interphase(SEI)formation.When paired with LiFePO_(4)cathodes,Si@BTO maintains 76% capacity retention after 500 cycles at a 10 C rate.This work establishes a basic force-electric coupling model framework and offers insights into the development of advanced silicon anode batteries with exceptional performance.
文摘This paper deals with the singular chemotaxis-Navier-Stokes system with indirect signal consumption n_(t)+u·▽v=△n-Х▽·(n/v▽u);v_(t)+u·▽v=△v-uw;w_(t)+u·▽w=△w-w+n;u_(t)+(u·▽)u=△u-▽P+n▽Ф;▽·u=0,x∈Ω,t>0 in a bounded and smooth domainΩ⊂ℝ2 with no-flux/no-flux/no-flux/no-slip boundary conditions,whereΦ∈W2,∞(Ω).A recent literature[Dai F,Liu B.J Differential Equations,2023,369:115–155]has proved that for all reasonably regular initial data,the associated initial-boundary value problem possesses a global classical solution,but qualitative information on the behavior of solution has never been touched so far.In stark contrast to the positive effect of indirect signal consumption mechanism on the global solvability of system,the analysis of asymptotic behavior of solution to the system with indirect signal consumption is essentially complicated than that with direct signal consumption because the favorable coupled structure between cells and signal is broken down by the indirect signal consumption mechanism.The present study shows that the global classical solution exponentially stabilizes toward the corresponding spatially homogeneous equilibria under a smallness condition on the initial cell mass.In comparison to the previously known result concerning the uniform convergence of solution to the system with direct signal consumption,our result inter alia provides a more in-depth understanding on the asymptotic behavior of solution.
基金support by FEDER-Fundo Europeu de Desenvolvimento Regional,through COMPETE 2020-Programa Operational Fatores de Competitividade,and the National Funds through FCT-Fundacao para a Ciencia e a Tecnologia,project no.UID/FIS/04650/2019support by FEDER-Fundo Europeu de Desenvolvimento Regional,through COMPETI E 2020-Programa Operacional Fatores de Competitividade,and the National Funds through FCT-Fundacao para a Ciencia e a Tecnologia,project no.POCI-01-0145-FEDER-028118
文摘We propose an adaptive stencil construction for high-order accurate finite volume schemes a posteriori stabilized devoted to solve one-dimensional steady-state hyperbolic equations.High accuracy(up to the sixth-order presently)is achieved,thanks to polynomial recon-structions while stability is provided with an a posteriori MOOD method which controls the cell polynomial degree for eliminating non-physical oscillations in the vicinity of dis-continuities.We supplemented this scheme with a stencil construction allowing to reduce even further the numerical dissipation.The stencil is shifted away from troubles(shocks,discontinuities,etc.)leading to less oscillating polynomial reconstructions.Experimented on linear,Burgers',and Euler equations,we demonstrate that the adaptive stencil technique manages to retrieve smooth solutions with optimal order of accuracy but also irregular ones without spurious oscillations.Moreover,we numerically show that the approach allows to reduce the dissipation still maintaining the essentially non-oscillatory behavior.
文摘We read with great interest the investigations conducted by Pourakbar et al.(2024)on the“Stabilization of clay soil using alkali-activated sewage sludge.”The authors have investigated the feasibility of utilizing alkali-activated sewage sludge(AASS)as a binder for stabilizing the clayey soil.Sewage sludge(SS)in varying proportions of 1.5%,2%,2.5%,3.5%,and 4.5%was utilized to prepare geopolymer binders using sodium and potassium-based alkali activators.Furthermore,unconfined compressive strength(UCS)and direct shear tests were conducted to examine the strength development of clayey soil stabilized with AASS.While the study presented some intriguing results,we have identified critical concerns regarding(i)the selection of SS as a precursor for alkali activation,(ii)technical inconsistencies associated with the compaction characteristics and microstructural analysis,and(iii)the feasibility of the proposed methodology for practical applications.Through our discussion,we seek to highlight these issues and provide constructive feedback to advance the understanding of alkali activation processes and their implications for soil stabilization.
基金supported by the NST Fellowship under the Ministry of Science and Technology,Government of the People’s Republic of Bangladesh(Session:2019–2020,merit number:334,serial number:714,physical science).
文摘This study presents a numerical analysis of the steady-state solution for transient magnetohydrodynamic(MHD)dissipative and radiative fluid flow,incorporating an inducedmagnetic field(IMF)and considering a relatively high concentration of foreign mass(accounting for Soret and Dufour effects)over a vertically oriented semi-infinite plate.The governing equations were normalized using boundary layer(BL)approximations.The resulting nonlinear system of partial differential equations(PDEs)was discretized and solved using an efficient explicit finite difference method(FDM).Numerical simulations were conducted using MATLAB R2015a,and the developed numerical code was verified through comparison with another code written in FORTRAN 6.6a.To ensure the reliability of the results,both mesh refinement and steady-state time validation tests were performed.Furthermore,a comparison with existing published studies was made to confirm the accuracy of the findings.The dimensionless equations revealed the impacts of several key parameters.The IMF initially intensifies near the plate before gradually diminishing as the magnetic parameter increases.For the range 0≤y≤1.8(where y is the horizontal direction),the IMF decreases with a rise in the magnetic Prandtl number;however,for 1.8≤y≤7(approximately),the magnetic field begins to increase.Beyond this,the profile of the magnetic field becomes somewhat irregular through the remaining part of the BL.
基金Deanship of Research and Graduate Studies at King Khalid University for funding this work through Large Research Project under grant number RGP.2/103/46”Deanship of Scientific Research at Northern Border University,Arar,Saudi Arabia for funding this research work through project number“NBU-FFR-2025-871-15”funding from Prince Sattam bin Abdulaziz University project number(PSAU/2025/R/1447).
文摘This paper proposes a model-based control framework for vehicle platooning systems with secondorder nonlinear dynamics operating over switching signed networks,time-varying delays,and deception attacks.The study includes two configurations:a leaderless structure using Finite-Time Non-Singular Terminal Bipartite Consensus(FNTBC)and Fixed-Time Bipartite Consensus(FXTBC),and a leader—follower structure ensuring structural balance and robustness against deceptive signals.In the leaderless model,a bipartite controller based on impulsive control theory,gauge transformation,and Markovian switching Lyapunov functions ensures mean-square stability and coordination under deception attacks and communication delays.The FNTBC achieves finite-time convergence depending on initial conditions,while the FXTBC guarantees fixed-time convergence independent of them,providing adaptability to different operating states.In the leader—follower case,a discontinuous impulsive control law synchronizes all followers with the leader despite deceptive attacks and switching topologies,maintaining robust coordination through nonlinear corrective mechanisms.To validate the approach,simulations are conducted on systems of five and seventeen vehicles in both leaderless and leader—follower configurations.The results demonstrate that the proposed framework achieves rapid consensus,strong robustness,and high resistance to deception attacks,offering a secure and scalable model-based control solution for modern vehicular communication networks.
基金supported by the National Natural Science Foundation of China(61803015).
文摘In order to enhance the dynamic control precision of inertial stabilization platform(ISP),a disturbance sliding mode observer(DSMO)is proposed in this paper suppressing disturbance torques inherent within the system.The control accuracy of ISP is fundamentally circumscribed by various disturbance torques in rotating shaft.Therefore,a dynamic model of ISP incorporating composite perturbations is established with regard to the stabilization of axis in the inertial reference frame.Subsequently,an online estimator for control loop uncertainties based on the sliding mode control algorithm is designed to estimate the aggregate disturbances of various parameters uncertainties and other unmodeled disturbances that cannot be accurately calibrated.Finally,the proposed DSMO is integrated into a classical proportional-integral-derivative(PID)control scheme,utilizing feedforward approach to compensate the composite disturbance in the control loop online.The effectiveness of the proposed disturbance observer is validated through simulation and hardware experimentation,demonstrating a significant improvement in the dynamic control performance and robustness of the classical PID controller extensively utilized in the field of engineering.
