A three-dimensional electrochemical oxidation （3D-EC） reactor with introduction of activated carbon （AC） as particle micro-electrodes was apphed for the advanced treatment of secondary wastewater effluent of a wet...A three-dimensional electrochemical oxidation （3D-EC） reactor with introduction of activated carbon （AC） as particle micro-electrodes was apphed for the advanced treatment of secondary wastewater effluent of a wet-spun acrylic fiber manufacturing plant. Under the optimized conditions （current density of 500 A/m2, circulation rate of 5 mL/min, AC dosage of 50 g, and chloride concentration of 1.0 g/L）, the average removal efficiencies of chemical oxygen demand （CODer）, NH3-N, total organic carbon （TOC）, and ultraviolet absorption at 254 nm （UV2s4） of the 3D-EC reactor were 64.5%, 60.8%, 46.4%, and 64.8%, respectively; while the corresponding effluent concentrations of CODcr, NH3-N, TOC, and UV2s4 were 76.6, 20.1, and 42.5 mg/L, and 0.08 Abs/cm, respectively. The effluent concentration of CODer was less than 100 mg/L, which showed that the treated wastewater satisfied the demand of the integrated wastewater discharge standard （GB 8978-1996）. The 3D-EC process remarkably improved the treatment efficiencies with synergistic effects for CODer, NH3-N, TOC, and UV2s4 during the stable stage of 44.5%, 38.8%, 27.2%, and 10.9%, respectively, as compared with the sum of the efficiencies of a two-dimensional electrochemical oxidation （2D-EC） reactor and an AC adsorption process, which was ascribed to the numerous micro-electrodes of AC in the 3D-EC reactor. Gas chromatography mass spectrometry （GC-MS） analysis revealed that electro- chemical treatment did not generate more toxic organics, and it was proved that the increase in acute biotoxicity was caused primarily by the production of free chlorine.展开更多
In this paper, fibrillation properties of solvent - spun cellulose fiber and some influencing factors are analyzed based on the experiment results. It is pointed out that special textile styles and aesthetic appearanc...In this paper, fibrillation properties of solvent - spun cellulose fiber and some influencing factors are analyzed based on the experiment results. It is pointed out that special textile styles and aesthetic appearance could be obtained by controlling the fibrillation.展开更多
It is believed that gel spun polyethylene(PE)fibers have a somewhat extended chain crystalstructure,because of the disentangling of the chains which takes place in semi-dilute solutionand the ultra high draw ratio use...It is believed that gel spun polyethylene(PE)fibers have a somewhat extended chain crystalstructure,because of the disentangling of the chains which takes place in semi-dilute solutionand the ultra high draw ratio used.Ten years ago,PE shish-kebabs grown from dilute solutionwere proved to have extended chain backbone which causes the raising of its melting point.These crystals were found to have a triclinic crystal phase,This study shows a different result forgel spun ultra high drawn PE fiber.The unit cell remains orthorhombic even if the draw ratioreaches 50;as the draw ratio increases,the length in a and b axes are shortened while that in c ax-is changes quite insignificantly.When the draw ratio is over 10,two endothermic melting peakscan be seen in the DSC curves with corresponding peak temperature of 136.7-145.3℃.The lat-ter peak is attributed to the amount of extended chain crystal.展开更多
Ultra-high strength and modulus polyethylene fibers can be produced from UHMW-PE(ul-tra-high molecular weight polyethylene) by gel spinning and ultra-high drawing method.The spe-cial supermolecular structure of″shish...Ultra-high strength and modulus polyethylene fibers can be produced from UHMW-PE(ul-tra-high molecular weight polyethylene) by gel spinning and ultra-high drawing method.The spe-cial supermolecular structure of″shish-kebabs″ is the intrinsic course for the fiber having highperformance.In this paper,the formation mechanism of the characteristic structure of PE fibershas been investigated by means of SEM,DSC,WAXD,SAXS and TEM,The experimental resultsshow that the extended-chain structure of PE fibers is formed originally from the bridged mole-cules in amorphous region and increased gradually during further drawing porcess.The″shish-kebab″ structure is formed by the combination of extended-chalnS and originalfolded-chains.展开更多
Consolidation of thermoplastic unidirectional(UD)lami-nate with friction spun core yarns was investigated,espe-cially the characterization of filament bundles in consoli-dation was analyzed.The results showed that the...Consolidation of thermoplastic unidirectional(UD)lami-nate with friction spun core yarns was investigated,espe-cially the characterization of filament bundles in consoli-dation was analyzed.The results showed that the bundleeffect was affected considerably by processing conditions(applied pressure and processing time).The boundaryof the bundles was disappeared under suitable processingconditions and finally an even fiber/resin distributioncould be attained.In consolidation,filament bundlesgetting close each other and resin flowing into the bundl-es occurred simultaneously,and eventually the bundleswere fully impregnated by the resin.Fiber packing den-sity in UD-laminate was the same as that of frictionspun core yarn(55%-65% in volume)and was not af-fected significantly by processing conditions under thecurrent experimental conditions.展开更多
基金supported by the Major Science and Technology Program for Water Pollution Control and Treatment (No. 2012ZX07201002-6)
文摘A three-dimensional electrochemical oxidation （3D-EC） reactor with introduction of activated carbon （AC） as particle micro-electrodes was apphed for the advanced treatment of secondary wastewater effluent of a wet-spun acrylic fiber manufacturing plant. Under the optimized conditions （current density of 500 A/m2, circulation rate of 5 mL/min, AC dosage of 50 g, and chloride concentration of 1.0 g/L）, the average removal efficiencies of chemical oxygen demand （CODer）, NH3-N, total organic carbon （TOC）, and ultraviolet absorption at 254 nm （UV2s4） of the 3D-EC reactor were 64.5%, 60.8%, 46.4%, and 64.8%, respectively; while the corresponding effluent concentrations of CODcr, NH3-N, TOC, and UV2s4 were 76.6, 20.1, and 42.5 mg/L, and 0.08 Abs/cm, respectively. The effluent concentration of CODer was less than 100 mg/L, which showed that the treated wastewater satisfied the demand of the integrated wastewater discharge standard （GB 8978-1996）. The 3D-EC process remarkably improved the treatment efficiencies with synergistic effects for CODer, NH3-N, TOC, and UV2s4 during the stable stage of 44.5%, 38.8%, 27.2%, and 10.9%, respectively, as compared with the sum of the efficiencies of a two-dimensional electrochemical oxidation （2D-EC） reactor and an AC adsorption process, which was ascribed to the numerous micro-electrodes of AC in the 3D-EC reactor. Gas chromatography mass spectrometry （GC-MS） analysis revealed that electro- chemical treatment did not generate more toxic organics, and it was proved that the increase in acute biotoxicity was caused primarily by the production of free chlorine.
文摘In this paper, fibrillation properties of solvent - spun cellulose fiber and some influencing factors are analyzed based on the experiment results. It is pointed out that special textile styles and aesthetic appearance could be obtained by controlling the fibrillation.
基金This project is supported by National Science Foundation of China
文摘It is believed that gel spun polyethylene(PE)fibers have a somewhat extended chain crystalstructure,because of the disentangling of the chains which takes place in semi-dilute solutionand the ultra high draw ratio used.Ten years ago,PE shish-kebabs grown from dilute solutionwere proved to have extended chain backbone which causes the raising of its melting point.These crystals were found to have a triclinic crystal phase,This study shows a different result forgel spun ultra high drawn PE fiber.The unit cell remains orthorhombic even if the draw ratioreaches 50;as the draw ratio increases,the length in a and b axes are shortened while that in c ax-is changes quite insignificantly.When the draw ratio is over 10,two endothermic melting peakscan be seen in the DSC curves with corresponding peak temperature of 136.7-145.3℃.The lat-ter peak is attributed to the amount of extended chain crystal.
文摘Ultra-high strength and modulus polyethylene fibers can be produced from UHMW-PE(ul-tra-high molecular weight polyethylene) by gel spinning and ultra-high drawing method.The spe-cial supermolecular structure of″shish-kebabs″ is the intrinsic course for the fiber having highperformance.In this paper,the formation mechanism of the characteristic structure of PE fibershas been investigated by means of SEM,DSC,WAXD,SAXS and TEM,The experimental resultsshow that the extended-chain structure of PE fibers is formed originally from the bridged mole-cules in amorphous region and increased gradually during further drawing porcess.The″shish-kebab″ structure is formed by the combination of extended-chalnS and originalfolded-chains.
文摘Consolidation of thermoplastic unidirectional(UD)lami-nate with friction spun core yarns was investigated,espe-cially the characterization of filament bundles in consoli-dation was analyzed.The results showed that the bundleeffect was affected considerably by processing conditions(applied pressure and processing time).The boundaryof the bundles was disappeared under suitable processingconditions and finally an even fiber/resin distributioncould be attained.In consolidation,filament bundlesgetting close each other and resin flowing into the bundl-es occurred simultaneously,and eventually the bundleswere fully impregnated by the resin.Fiber packing den-sity in UD-laminate was the same as that of frictionspun core yarn(55%-65% in volume)and was not af-fected significantly by processing conditions under thecurrent experimental conditions.
