A series of steady and unsteady numerical calculations of the internal flow in mixed-flow pumps with three different specific speeds were carried out based on the N-S equation coupled with the standard k-εturbulence ...A series of steady and unsteady numerical calculations of the internal flow in mixed-flow pumps with three different specific speeds were carried out based on the N-S equation coupled with the standard k-εturbulence model under different operating conditions to investigate the relationship between the impeller specific speed and the pump performance as well as pressure pulsations.Meanwhile,the pump performance and pressure pulsations inside the mixed-flow pump with three different specific speeds were also analyzed and compared with the corresponding test data.From the results,the averaged deviations between the predicted and tested head among different impellers are below 5%,and with respect to the equivalent impeller specific speeds of 280 and 260,the values are 4.30%and 3.69%,respectively.For all the impeller schemes,the best efficiency point of the mixed-flow pump is found at the flow rate of 1.2 Q_(d) and the higher head deviation occurs at lower flow rates.Especially,it can be found that the specific speed has a slight effect on the pressure fluctuation in the impellers.Eventually,it is determined that the pump performance curves calculated by numerical simu-lations have good agreement with the relevant experimental results,which verifies that the numerical methods used in the present study are accurate to a certain extent.Furthermore,the results also provide some references to the pressure pulsation analysis and the performance improvement of the mixed-flow pump design.展开更多
The ultra-low specific speed centrifugal blower is widely used in energy industries due to its features such as low flow rate,high pressure and low manufacturing cost. However,the width-to-diameter ratio of the above ...The ultra-low specific speed centrifugal blower is widely used in energy industries due to its features such as low flow rate,high pressure and low manufacturing cost. However,the width-to-diameter ratio of the above blower becomes relatively small to satisfy the needed operation condition and its performances are considerably degraded as a result of relatively high leakage,disc friction and passage friction loss consequently. The purpose of this paper is to improve its performance through the optimization design of the blade’s profile properly. Based on artificial neural networks (ANN) and hierarchical fair competition genetic algorithms with dynamic niche (HFCDN-GAs),the optimization design approach is established. By conjoining Bezier parameterization and FINE/TURBO solver,the optimized blade is designed by adjusting the profile gradually. An industrial ultra-low specific speed centrifugal blower with parallel hub and shroud has been selected as a reference case for optimization design. The performance investigations of the centrifugal blowers with different types of blades are conducted. The conclusions of the performance improvement of the optimized blade provide positive evidences in the application of the optimization design of the above blower blade.展开更多
This paper aims to clarify the cavitation suppression mechanism of the gap structure impeller based on the analysis of cavitation characteristics in a low specific speed centrifugal pump. In order to obtain reliable a...This paper aims to clarify the cavitation suppression mechanism of the gap structure impeller based on the analysis of cavitation characteristics in a low specific speed centrifugal pump. In order to obtain reliable and consistent numerical results, some numerical considerations and modeling methodology were demonstrated and researched, and a check of the time and space resolution were also conducted. Hence the predicted cavitation performance of the two centrifugal pumps were investigated and compared with experimental results, and they were in qualitative agreement. It was confirmed that the new gap structure impeller has a very good characteristic of inhibiting cavitation, especially in large flow area, the present numerical method can effectively capture the major internal flow features in the centrifugal pump, through the comparison of the two type impeller flow fields, the cavitation suppression mechanism of the gap impeller may be the combination effects of the small vice blade＇s guiding flow and gap tunnel＇s auto-balancing of pressure.展开更多
A three-dimensional transient numerical simulation was conducted to study the pressure fluctuations in low-specific-speed centrifugal pumps. The characteristics of the inner flow were investigated using the SST k-ω t...A three-dimensional transient numerical simulation was conducted to study the pressure fluctuations in low-specific-speed centrifugal pumps. The characteristics of the inner flow were investigated using the SST k-ω turbulence model. The distributions of pressure fluctuations in the impeller and the volute were recorded, and the pressure fluctuation intensity was analyzed comprehensively, at the design condition, using statistical methods. The results show that the pressure fluctuation intensity increases along the impeller streamline from the leading edge to the trailing edge. In the impeller passage, the intensity near the shroud is much higher than that near the hub at thc inlet. However, the intensity at the middle passage is almost equal to the intensity at the outlet. The pressure fluctuation intensity is the highest at the trailing edge on the pressure side and near the tongue because of the rotor-stator interaction. The distribution of pressure fluctuation intensity is symmetrical in the axial cross sections of the volute channel. However, this intensity decreases with increasing radial distance. Hence, the pressure fluctuation intensity can be reduced by modifying the geometry of the leading edge in the impeller and the tongue in the volute.展开更多
基金National Natural Science Foundation of China(51976078)Senior Personnel Scientific Research Foundation of Jiangsu University:(15JDG073)Open Research Subject of Key Laboratory of Fluid and Power Machinery,Ministry of Education(szjj2016-065)。
文摘A series of steady and unsteady numerical calculations of the internal flow in mixed-flow pumps with three different specific speeds were carried out based on the N-S equation coupled with the standard k-εturbulence model under different operating conditions to investigate the relationship between the impeller specific speed and the pump performance as well as pressure pulsations.Meanwhile,the pump performance and pressure pulsations inside the mixed-flow pump with three different specific speeds were also analyzed and compared with the corresponding test data.From the results,the averaged deviations between the predicted and tested head among different impellers are below 5%,and with respect to the equivalent impeller specific speeds of 280 and 260,the values are 4.30%and 3.69%,respectively.For all the impeller schemes,the best efficiency point of the mixed-flow pump is found at the flow rate of 1.2 Q_(d) and the higher head deviation occurs at lower flow rates.Especially,it can be found that the specific speed has a slight effect on the pressure fluctuation in the impellers.Eventually,it is determined that the pump performance curves calculated by numerical simu-lations have good agreement with the relevant experimental results,which verifies that the numerical methods used in the present study are accurate to a certain extent.Furthermore,the results also provide some references to the pressure pulsation analysis and the performance improvement of the mixed-flow pump design.
基金supported by the National Natural Science Foundation of China (Grant No.50776056)the National High Technology Research and Development Program of China ("863" Program) (Grant No.2009AA05Z201)
文摘The ultra-low specific speed centrifugal blower is widely used in energy industries due to its features such as low flow rate,high pressure and low manufacturing cost. However,the width-to-diameter ratio of the above blower becomes relatively small to satisfy the needed operation condition and its performances are considerably degraded as a result of relatively high leakage,disc friction and passage friction loss consequently. The purpose of this paper is to improve its performance through the optimization design of the blade’s profile properly. Based on artificial neural networks (ANN) and hierarchical fair competition genetic algorithms with dynamic niche (HFCDN-GAs),the optimization design approach is established. By conjoining Bezier parameterization and FINE/TURBO solver,the optimized blade is designed by adjusting the profile gradually. An industrial ultra-low specific speed centrifugal blower with parallel hub and shroud has been selected as a reference case for optimization design. The performance investigations of the centrifugal blowers with different types of blades are conducted. The conclusions of the performance improvement of the optimized blade provide positive evidences in the application of the optimization design of the above blower blade.
基金supported by the National Science and Technology Foundation of China(Grant No.51179100)the Key Research Projects of Shanghai Science and Technology Commission(Grant No.10100500200)+1 种基金the Shanghai Program for Innovative Research Team in Universitiessupported by the Graduate Student Innovation Foundation of Shanghai University(Grant No.SHUCX111010)
文摘This paper aims to clarify the cavitation suppression mechanism of the gap structure impeller based on the analysis of cavitation characteristics in a low specific speed centrifugal pump. In order to obtain reliable and consistent numerical results, some numerical considerations and modeling methodology were demonstrated and researched, and a check of the time and space resolution were also conducted. Hence the predicted cavitation performance of the two centrifugal pumps were investigated and compared with experimental results, and they were in qualitative agreement. It was confirmed that the new gap structure impeller has a very good characteristic of inhibiting cavitation, especially in large flow area, the present numerical method can effectively capture the major internal flow features in the centrifugal pump, through the comparison of the two type impeller flow fields, the cavitation suppression mechanism of the gap impeller may be the combination effects of the small vice blade＇s guiding flow and gap tunnel＇s auto-balancing of pressure.
基金Projects(51239005,51009072) supported by the National Natural Science Foundation of ChinaProject(2011BAF14B04) supported by the National Science&Technology Pillar Program of ChinaProject(13JDG084) supported by the Research Foundation for Advanced Talents of Jiansu University,China
文摘A three-dimensional transient numerical simulation was conducted to study the pressure fluctuations in low-specific-speed centrifugal pumps. The characteristics of the inner flow were investigated using the SST k-ω turbulence model. The distributions of pressure fluctuations in the impeller and the volute were recorded, and the pressure fluctuation intensity was analyzed comprehensively, at the design condition, using statistical methods. The results show that the pressure fluctuation intensity increases along the impeller streamline from the leading edge to the trailing edge. In the impeller passage, the intensity near the shroud is much higher than that near the hub at thc inlet. However, the intensity at the middle passage is almost equal to the intensity at the outlet. The pressure fluctuation intensity is the highest at the trailing edge on the pressure side and near the tongue because of the rotor-stator interaction. The distribution of pressure fluctuation intensity is symmetrical in the axial cross sections of the volute channel. However, this intensity decreases with increasing radial distance. Hence, the pressure fluctuation intensity can be reduced by modifying the geometry of the leading edge in the impeller and the tongue in the volute.
