Sm0.2Ce0.8O1.9 （SDC） electrolyte was prepared by a modified solid state method at relatively low sintering temperatures without any sintering promoters. The phase composition and microstructure of the electrolytes w...Sm0.2Ce0.8O1.9 （SDC） electrolyte was prepared by a modified solid state method at relatively low sintering temperatures without any sintering promoters. The phase composition and microstructure of the electrolytes were investigated by X-ray diffraction （XRD） and field emission scanning electron microscopy （FESEM） technologies. A relative density of SDC electrolyte sintered at 1300 ℃ reached 97.3%and the mean SDC grain size was about 770 nm. Their ionic conductivity and thermal expansion coefficient were also measured by electrochemical workstation and dilatometer. The electrolyte attained a high conductivity of 5×10^-2 S/cm at 800 ℃ with an activation energy of 1.03 eV and a proper thermal expansion coefficient of 12.6×10^-6 K^-1.展开更多
Employing Li2CO3, NiO, Co3O4, and MnCO3 powders as starting materials, Li[Ni1/3Co1/3Mn1/3]O2 was synthesized by solid-state reaction method. Various grinding aids were applied during milling in order to optimize the s...Employing Li2CO3, NiO, Co3O4, and MnCO3 powders as starting materials, Li[Ni1/3Co1/3Mn1/3]O2 was synthesized by solid-state reaction method. Various grinding aids were applied during milling in order to optimize the synthesis process. After successive heat treatments at 650 and 950 ℃, the prepared powders were characterized by X-ray diffraction (XRD) analysis, scanning electron microscopy, and transmission electron microscopy. The powders prepared by adding salt (NaCl) as grinding aid exhibit a clear R3m layer structure. The powders by other grinding aids like heptane show some impurity peaks in the XRD pattern. The former powders show a uniform particle size distribution of less than 1 μm average size while the latter shows a wide distribution ranging from 1 to 10 μm. Energy dispersive X-ray (EDX) analysiss show that the ratio of Ni, Co, and Mn content in the powder is approximately 1/3, 1/3, and 1/3, respecively. The EDX data indicate no incorporation of sodium or chlorine into the powders. Charge-discharge tests gave an initial discharge capacity of 160 mAh·g-1 for the powders with NaCl addition while 70 mAh·g-1 for the powders with heptane.展开更多
Micro silicon(mSi)is a promising anode candidate for all-solid-state batteries due to its high specific capacity,low side reactions,and high tap density.However,silicon suffers from its poor electronic and ionic condu...Micro silicon(mSi)is a promising anode candidate for all-solid-state batteries due to its high specific capacity,low side reactions,and high tap density.However,silicon suffers from its poor electronic and ionic conductivity,which is particularly severe on a micro scale and in solid-state systems,leading to increased polarization and inferior electrochemical performance.Doping can broaden the transmission pathways and reduce the diffusion energy barrier for electrons and lithium ions.However,achieving effective,uniform doping in mSi is challenging due to its longer diffusion paths and higher energy barriers.Therefore,current doping research is primarily limited to nanosilicon.In this study,we successfully used a Joule-heating activated staged thermal treatment to achieve full-depth doping of germanium(Ge)in the mSi substrate.The Joule-heating process activated the mSi substrate,resulting in abundant vacancy defects that reduced the diffusion barrier of Ge into the silicon lattice and facilitated full-depth Ge doping.Surprisingly,the resulting Si-Ge anode exhibited significantly enhanced electrical conductivity(70 times).Meanwhile,the improved Li-ion conductivity in mSi and the reduced Young’s modulus enhance the electrode reaction kinetics and integrity after cycling.Ge-doped silicon anodes demonstrate excellent electrochemical performance when applied in sulfide solid-state half-cells and full-cells.This work provides substantial insights into the rational structural design of mSi alloyed anode materials,paving the way for the development of high-performance solid-state Li-ion batteries.展开更多
Polyethylene oxide(PEO)-based solid polymer electrolytes(SPEs)have long faced limitations due to low ionic conductivity at ambient temperature and poor interfacial stability with lithium metal anodes.Here,we present a...Polyethylene oxide(PEO)-based solid polymer electrolytes(SPEs)have long faced limitations due to low ionic conductivity at ambient temperature and poor interfacial stability with lithium metal anodes.Here,we present a structural engineering strategy to address these challenges through shear-induced crystallization of concentrated PEO-LiTFSI solutions,which self-assemble into flower-like spherulites with radially aligned lamellar crystals.This unique structure creates continuous Li^(+)transport highways through densely packed crystalline domains,achieving a record-high ionic conductivity of 1.70×10^(-4) S/cm at 25℃ for pristine PEO-based systems.Strategic incorporation of lithium montmorillonite(MMTli,10 wt%)further optimizes the composite electrolyte,balancing high ionic conductivity(1.47×10^(-4) S/cm)with enhanced electrochemical stability(4.99 V vs.Li^(+)/Li),elevated Li^(+)transference number(0.62),and mechanical robustness.The composite electrolyte enables stable Li plating/stripping over 800 h in symmetric Li||Li cells and powers LiFePO_(4)||Li solid-state batteries with 82%capacity retention after 200 cycles at 0.2 C under ambient conditions.This work pioneers a scalable processing paradigm for crystalline polymer electrolytes,offering new insights into ion transport mechanisms and validating clay minerals as multifunctional additives for next-generation energy storage systems.展开更多
All-solid-state batteries(ASSBs)represent a next-generation energy storage technology,offering enhanced safety,higher energy density,and improved cycling stability compared to conventional liquid-electrolyte-based lit...All-solid-state batteries(ASSBs)represent a next-generation energy storage technology,offering enhanced safety,higher energy density,and improved cycling stability compared to conventional liquid-electrolyte-based lithium-ion batteries.Understanding and optimizing the complex chemistries and interfaces that underpin ASSB performance present significant challenges from both experimental and modeling perspectives.In particular,atomistic simulations face difficulties in capturing the complex structure,disorder,and dynamic evolution of materials and interfaces under practically relevant conditions.While established methods such as density functional theory and classical force fields have provided valuable insights,some questions remain difficult to address,particularly those involving large system sizes or long timescales.Recently,machine learning interatomic potentials(MLIPs)have emerged as a transformative tool,enabling atomistic simulations at length and time scales that were previously challenging to access with conventional approaches.By delivering near first-principles accuracy with much greater efficiency,MLIPs open new avenues for large-scale,long-timescale,and high-throughput simulations of solid-state battery materials.In this review,we present a comparative overview of density functional theory,classical force fields,and MLIPs,highlighting their respective strengths and limitations in ASSB research.We then discuss how MLIPs enable simulations that reach longer timescales,larger system sizes,and support high-throughput calculations,providing unique insights into ion transport and interfacial evolution in ASSBs.Finally,we conclude with a summary and outlook on current challenges and future opportunities for expanding MLIP capabilities and accelerating their impact in solid-state battery research.展开更多
In the realm of large-scale power system energy storage,sodium-based batteries represent a cost-effective post-lithium energy storage technology,making inorganic solid-state sodium batteries(ISSSB)a critical branch of...In the realm of large-scale power system energy storage,sodium-based batteries represent a cost-effective post-lithium energy storage technology,making inorganic solid-state sodium batteries(ISSSB)a critical branch of this development.Inorganic solid-state electrolytes(ISSEs)are the core components of sodium batteries;however,they face significant challenges such as insufficient ionic conductivity,interfacial instability,and dendrite growth,all of which severely hinder practical application.This review critically assesses experimental protocols and theoretical frameworks related to mainstream ISSEs and systematizes optimization strategies aimed at overcoming these challenges.Leveraging integrated insights from both experimental and computational studies,the review first categorizes and summarizes the primary types of ISSEs,namely oxide-,sulfide-,and halide-based electrolytes.It then details interfacial optimization strategies focused on addressing three core interfacial issues:ion transport barriers resulting from mechanical incompatibility,side reactions stemming from electrochemical mismatch,and dendrite formation.Finally,the review advocates prioritizing in-depth research that integrates experimental and theoretical approaches to establish a closed-loop methodology encompassing predictive design,multiscale investigation,mechanistic exploration,and high-throughput automated experimentation,with feedback-driven refinement.This work serves as a comprehensive reference and systematic roadmap for future research on solid-state electrolytes(SSEs).展开更多
Thermoplastic polyurethane(TPU)consists of a hardsegment and a soft segment,where the former affords mechanical strength and thermalstability,while the latter provides a possibility of good ionic conductivity by promo...Thermoplastic polyurethane(TPU)consists of a hardsegment and a soft segment,where the former affords mechanical strength and thermalstability,while the latter provides a possibility of good ionic conductivity by promoting dissociation of ions from the lithium salt.Thus,TPU attracts a wide interest recently as a promising polymer electrolyte for solid-state lithium batteries.However,the relatively low ionic conductivity of TPU still restricts its actual applications due to the aggregation of polymer chains,which greatly reduces the dissociation of lithium salts.Herein,a strategy to address this challenge was adopted by in situ polymerization poly(ethylene glycol diacrylate)(PEGDA)in fully dispersed TPU.Hence a stretchable solid-state electrolyte(denoted as TELL and the contrast sample was denoted as TLL)with high ionic conductivity of 7.18×10^(-4) S/cm was obtained at room temperature.The Li^(+)transference number is 0.85 in Li|TELL|Li cell and can stably undergo charge-discharge cycles for 1400 h at a current density of O.1 mA/cm^(2),while the contrast sample is short-circuited after 634 h of cycling.The LiFePO_(4)|TELL|Li cell achieves a capacity retention of 78.93%after 200 cycles at 2 C.The LiFePO_(4) TLL Li cellonly gains the capacity retention of 51.9%after 50 cyclesat the same current density.So,the method adopted here may provide a new approach to realize a flexible solid-state electrolyte with high ion-conductivity.展开更多
Ribonucleic acid(RNA)structures and dynamics play a crucial role in elucidating RNA functions and facilitating the design of drugs targeting RNA and RNA-protein complexes.However,obtaining RNA structures using convent...Ribonucleic acid(RNA)structures and dynamics play a crucial role in elucidating RNA functions and facilitating the design of drugs targeting RNA and RNA-protein complexes.However,obtaining RNA structures using conventional biophysical techniques,such as Xray crystallography and solution nuclear magnetic resonance(NMR),presents challenges due to the inherent flexibility and susceptibility to degradation of RNA.In recent years,solid-state NMR(SSNMR)has rapidly emerged as a promising alternative technique for characterizing RNA structure and dynamics.SSNMR has several distinct advantages,including flexibility in sample states,the ability to capture dynamic features of RNA in solid form,and suitability to character RNAs in various sizes.Recent decade witnessed the growth of ^(1)H-detected SSNMR methods on RNA,which targeted elucidating RNA topology and base pair dynamics in solid state.They have been applied to determine the topology of RNA segment in human immunodeficiency virus(HIV)genome and the base pair dynamics of riboswitch RNA.These advancements have expanded the utility of SSNMR techniques within the RNA research field.This review provides a comprehensive discussion of recent progress in ^(1)H-detected SSNMR investigations into RNA structure and dynamics.We focus on the established ^(1)H-detected SSNMR methods,sample preparation protocols,and the implementation of rapid data acquisition approaches.展开更多
An approach called hybrid heat-source solid-state additive manufacturing (HHSAM) for fabricating multilayer AA6061 deposition with superior properties is proposed in this paper. As compared with the traditional additi...An approach called hybrid heat-source solid-state additive manufacturing (HHSAM) for fabricating multilayer AA6061 deposition with superior properties is proposed in this paper. As compared with the traditional additive friction stir deposition (AFSD), the auxiliary induction heat-source in HHSAM effectively improves the temperature and fluidity of plastic flow, which facilitates the formation and enrichment of residual Mg_(2)Si phases besides Al(Fe,Mn)Si, promotes the dynamic recrystallization and increases the bonding strength between layers during the deposition process. Therefore, the HHSAM depositions possess a more uniform structure, superior integral mechanical properties and corrosion resistance after heat treatment process. Moreover, HHSAMed specimens avoid abnormal grain growth (AGG) in heat treatment process, which is regularly encountered in the traditional AFSD. HHSAM method is proved to be a new solid-state additive manufacturing method with good developing prospects for fabricating alloy production with excellent properties in a high-efficiency manner.展开更多
Oily cold rolling mill （CRM） sludge is one of the pollutants emitted by iron and steel plants. Recycling oily CRM sludge can not only reduce pollution but also bring social and environmental benefits. In this study,...Oily cold rolling mill （CRM） sludge is one of the pollutants emitted by iron and steel plants. Recycling oily CRM sludge can not only reduce pollution but also bring social and environmental benefits. In this study, using oily CRM sludge as sources of iron oxide, the strontium ferrite powders were synthesized in multiple steps including vacuum distillation, magnetic separation, oxidizing roasting, and solidstate reaction. The optimal technological conditions of vacuum distillation and oxidizing roasting were studied carefully. To consider the effects of Fe203/ SrCO3 tool ratio, calcination temperature, milling time and calcination time on magnetic properties of prepared strontium ferrite powders, the orthogonal experimental method was adopted. The maximum saturation magneti- zation （62.6 mA-m2.g-1） of the synthesized strontium ferrite powders was achieved at the Fe203/SrCO3 mol ratio of 6, 5 h milling time, 1250 ~C calcination temperature, and 1 h calcination time. Strontium ferrite powders syn- thesis method not only provides a cheap, high quality raw material for the production of strontium ferrite powders, but also effectively prevents the environmental pollution.展开更多
This study shows that sulfide solid-state electrolytes,β-Li_(3)PS_(4)and Li_(6)PS_(5)Cl,are flammable solids.Both solid-state electrolytes release sulfur vapor in a dry,oxidizing environment at elevated temperature&l...This study shows that sulfide solid-state electrolytes,β-Li_(3)PS_(4)and Li_(6)PS_(5)Cl,are flammable solids.Both solid-state electrolytes release sulfur vapor in a dry,oxidizing environment at elevated temperature<300℃.Sulfur vapor is a highly flammable gas,which then auto-ignites to produce a flame.This behavior suggests that an O_(2)-S gas-gas reaction mechanism may contribute to all-solid-state battery thermal runaway.To improve all-solid-state battery safety,current work focuses on eliminating the O_(2)source by changing the cathode active material.The conclusion of this study suggests that all-solidstate battery safety can also be realized by the development of solid-state electrolytes with less susceptibility to sulfur volatilization.展开更多
The formation mechanism of calcium vanadate and manganese vanadate and the difference between calcium and manganese in the reaction with vanadium are basic issues in the calcification roasting and manganese roasting p...The formation mechanism of calcium vanadate and manganese vanadate and the difference between calcium and manganese in the reaction with vanadium are basic issues in the calcification roasting and manganese roasting process with vanadium slag.In this work,CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples were prepared and roasted for different time periods to illustrate and compare the diffusion reaction mechanisms.Then,the changes in the diffusion product and diffusion coefficient were investigated and calculated based on scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS) analysis.Results show that with the extension of the roasting time,the diffusion reaction gradually proceeds among the CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples.The regional boundaries of calcium and vanadium are easily identifiable for the CaO–V_(2)O_(5) diffusion couple.Meanwhile,for the MnO_(2)–V_(2)O_(5) diffusion couple,MnO_(2) gradually decomposes to form Mn_(2)O_(3),and vanadium diffuses into the interior of Mn_(2)O_(3).Only a part of vanadium combines with manganese to form the diffusion production layer.CaV_(2)O_(6) and MnV_(2)O_(6) are the interfacial reaction products of the CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples,respectively,whose thicknesses are 39.85 and 32.13μm when roasted for 16 h.After 16 h,both diffusion couples reach the reaction equilibrium due to the limitation of diffusion.The diffusion coefficient of the CaO–V_(2)O_(5) diffusion couple is higher than that of the MnO_(2)–V_(2)O_(5) diffusion couple for the same roasting time,and the diffusion reaction between vanadium and calcium is easier than that between vanadium and manganese.展开更多
High-nickel ternary cathodes hold a great application prospect in solid-state lithium metal batteries to achieve high-energy density,but they still suffer from structural instability and detrimental side reactions wit...High-nickel ternary cathodes hold a great application prospect in solid-state lithium metal batteries to achieve high-energy density,but they still suffer from structural instability and detrimental side reactions with the solid-state electrolytes.To circumvent these issues,a continuous uniform layer polyacrylonitrile(PAN)was introduced on the surface of LiNi_(0.8)Mn_(0.1)Co_(0.1)O_(2) via in situ polymerization of acrylonitrile(AN).Furthermore,the partial-cyclized treatment of PAN(cPAN)coating layer presents high ionic and electron conductivity,which can accelerate interfacial Li+and electron diffusion simultaneously.And the thermodynamically stabilized cPAN coating layer cannot only effectively inhibit detrimental side reactions between cathode and solid-state electrolytes but also provide a homogeneous stress to simultaneously address the problems of bulk structural degradation,which contributes to the exceptional mechanical and electrochemical stabilities of the modified electrode.Besides,the coordination bond interaction between the cPAN and NCM811 can suppress the migration of Ni to elevate the stability of the crystal structure.Benefited from these,the In-cPAN-260@NCM811 shows excellent cycling performance with a retention of 86.8%after 300 cycles and superior rate capability.And endow the solid-state battery with thermal safety stability even at hightemperature extreme environment.This facile and scalable surface engineering represents significant progress in developing high-performance solid-state lithium metal batteries.展开更多
With the widespread adoption of lithium-ion batteries(LIBs),safety concerns associated with flammable organic elec-trolytes have become increasingly critical.Solid-state lithium batteries(SSLBs),with enhanced safety a...With the widespread adoption of lithium-ion batteries(LIBs),safety concerns associated with flammable organic elec-trolytes have become increasingly critical.Solid-state lithium batteries(SSLBs),with enhanced safety and higher energy density potential,are regarded as a promising next-generation energy storage technology.However,the practical appli-cation of solid-state electrolytes(SSEs)remains hindered by several challenges,including low Li^(+)ion conductivity,poor interfacial compatibility with electrodes,unfavorable mechanical properties and difficulties in scalable manufacturing.This review systematically examines recent progress in SSEs,including inorganic types(oxides,sulfides,halides),organic types(polymers,plastic crystals,poly(ionic liquids)(PILs)),and the emerging class of soft solid-state electrolytes(S3Es),especially those based on“rigid-flexible synergy”composites and“Li+-desolvation”mechanism using porous frameworks.Critical assessment reveals that single-component SSEs face inherent limitations that are difficult to be fully overcome through compositional and structural modification alone.In contrast,S3Es integrate the strength of complementary components to achieve a balanced and synergic enhancement in electrochemical properties(e.g.,ionic conductivity and stability window),mechanical integrity,and processability,showing great promise as next-generation SSEs.Furthermore,the application-ori-ented challenges and emerging trends in S3E research are outlined,aiming to provide strategic insights into future develop-ment of high-performance SSEs.展开更多
Three individual peaks of thermal solid-state reaction processes of the synthesized Mn0.90Co0.05Mg0.05HPO4?3H2O were observed corresponding to dehydration I,dehydration II and polycondensation processes.An alternative...Three individual peaks of thermal solid-state reaction processes of the synthesized Mn0.90Co0.05Mg0.05HPO4?3H2O were observed corresponding to dehydration I,dehydration II and polycondensation processes.An alternative method for the calculation of the extent of conversion was proposed from the peak area of the individual DTG peak after applying the best fitting deconvolution function(Frazer–Suzuki function).An iterative integral isoconversional equation was used to compute the values of the apparent activation energy Eαand they were found to be 65.87,78.16 and 119.32 kJ/mol for three peaks,respectively.Each individual peak was guaranteed to be a single-step kinetic system with its unique kinetic parameters.The reaction mechanism functions were selected by the comparison between experimental and model plots.The results show that the first,second and final individual peaks were two-dimensional diffusion of spherical symmetry(D2),three-dimensional diffusion of spherical symmetry(D3)and contracting cylinder(cylindrical symmetry,R2)mechanisms.Pre-exponential factor values of 3.91×106,1.35×107 and 2.15×107 s?1 were calculated from the Eαvalues and reaction mechanisms.The corresponded standard thermodynamic functions of the transition-state(activated)complexes were determined and found to agree well with the experimental data.展开更多
Solid-state electrolytes(SSEs),as the core component within the next generation of key energy storage technologies-solid-state lithium batteries(SSLBs)-are significantly leading the development of future energy storag...Solid-state electrolytes(SSEs),as the core component within the next generation of key energy storage technologies-solid-state lithium batteries(SSLBs)-are significantly leading the development of future energy storage systems.Among the numerous types of SSEs,inorganic oxide garnet-structured superionic conductors Li7La3Zr2O12(LLZO)crystallized with the cubic Iaˉ3d space group have received considerable attention owing to their highly advantageous intrinsic properties encompassing reasonable lithium-ion conductivity,wide electrochemical voltage window,high shear modulus,and excellent chemical stability with electrodes.However,no SSEs possess all the properties necessary for SSLBs,thus both the ionic conductivity at room temperature and stability in ambient air regarding cubic garnet-based electrolytes are still subject to further improvement.Hence,this review comprehensively covers the nine key structural factors affecting the ion conductivity of garnet-based electrolytes comprising Li concentration,Li vacancy concentration,Li carrier concentration and mobility,Li occupancy at available sites,lattice constant,triangle bottleneck size,oxygen vacancy defects,and Li-O bonding interactions.Furthermore,the general illustration of structures and fundamental features being crucial to chemical stability is examined,including Li concentration,Li-site occupation behavior,and Li-O bonding interactions.Insights into the composition-structure-property relations among cubic garnet-based oxide ionic conductors from the perspective of their crystal structures,revealing the potential compatibility conflicts between ionic transportation and chemical stability resulting from Li-O bonding interactions.We believe that this review will lay the foundation for future reasonable structural design of oxide-based or even other types of superionic conductors,thus assisting in promoting the rapid development of alternative green and sustainable technologies.展开更多
Safety issues induced by infinite anode volume change and uncontrolled lithium(Li)dendrite growth have become the biggest obstacle to the practical application of Li metal batteries.In addition,the tra-ditional rollin...Safety issues induced by infinite anode volume change and uncontrolled lithium(Li)dendrite growth have become the biggest obstacle to the practical application of Li metal batteries.In addition,the tra-ditional rolling method makes it difficult to manufacture thin Li foil with high mechanical strength and low Li content.Herein,a three-dimensional(3D)lithophilic carbon paper/copper(Cu)current collector hybrid anode with ultra-low Li metal content is prepared by a hot-pressing method.The highly re-versible and stable lithiophilic layer LiC_(x) formed in situ by heating/pressing treatment provides abun-dant nucleation sites and reduces the Li nucleation overpotential,thereby effectively suppressing Li den-drite growth.Moreover,the volume change and pulverization problems of Li metal anode during depo-sition/stripping also can be accommodated by the 3D skeleton.The optimization effect has been directly confirmed by in-situ optical and ex-situ scanning electron microscope observation.Therefore,highly sta-ble performance(158.4 mA h g^(-1) at 2 C after 200 cycles with a capacity retention of 95.24%)in Li@LCP-Cu||NCM811 coin cell can be achieved.Furthermore,the solid-state battery assembled with the hybrid anode,poly(vinylidene fluoride)(PVDF)-based polymer electrolyte and polyethylene oxide(PEO)interface functional layer also exhibits the best electrochemical and safety performance,which also proves that the Li@LCP-Cu anode has great potential for application in solid-state batteries.展开更多
Severe structural fractures and persistent side reactions at the interface with liquid electrolytes have hindered the commercialization of silicon(Si)anodes.Solid-state electrolytes present a promising solution to add...Severe structural fractures and persistent side reactions at the interface with liquid electrolytes have hindered the commercialization of silicon(Si)anodes.Solid-state electrolytes present a promising solution to address these issues.However,the high interfacial resistance of rigid ceramic electrolytes and the limited ionic conductivity of polymer electrolytes remain significant challenges,further complicated by the substantial volume expansion of Si.In this work,we chemically grafted a flame-retardant,self-healing polyurethane-thiourea polymer onto Li_(7)P_(3)S_(11)(SHPUSB-40%LPS)via nucleophilic addition,creating an electrolyte with exceptional ionic conductivity,high elasticity,and strong compatibility with Si anodes.We observed that FSI^(-)was strongly adsorbed onto the LPS surface through electrostatic interactions with sulfur vacancies,enhancing Li^(+)transport.Furthermore,SHPUSB-40%LPS exhibits dynamic covalent disulfide bonds and hydrogen bonds,enabling self-assembly of the electrolyte at the interface.This dynamic bonding provides a self-healing mechanism that mitigates structural changes during Si expansion and contraction cycles.As a result,the Si anode with SHPUSB-40%LPS presents excellent cycling stability,retaining nearly 53.5%of its capacity after 300 cycles.The practical applicability of this design was validated in a 2 Ah all-solid-state Si‖LiNi_(0.6)Mn_(0.2)Co_(0.2)O_(2)pouch cell,which maintained a stable Li-ion storage capacity retention of 76.3%after 350cycles at 0.5C.This novel solid-state electrolyte with selfhealing properties offers a promising strategy to address fundamental interfacial and performance challenges associated with Si anodes.展开更多
Composite solid electrolytes(CSEs)are considered among the most promising candidates for solid-state batteries.However,their practical application is hindered by low ionic conductivity and a limited lithium-ion transf...Composite solid electrolytes(CSEs)are considered among the most promising candidates for solid-state batteries.However,their practical application is hindered by low ionic conductivity and a limited lithium-ion transference number,primarily owing to the insufficient mobility of Li+.In this work,we design a heterojunc-tion nanoparticle composed of bimetallic zeolitic imidazolate frameworks(ZIFs)coupled with amorphous tita-nium oxide(TiO_(2)@Zn/Co–ZIF)as a filler to fabricate a composite solid-state electrolyte(PVZT).The amor-phous TiO_(2) coating facilitates salt dissociation through Lewis acid–base interactions with the anions of the lithium salt.Meanwhile,the Zn/Co–ZIF framework not only provides additional selective pathways for Li+transport but also effectively restricts anion migration through its confined pore size.The synergistic effect results in a high room-temperature ionic conductivity(8.8×10^(-4) S·cm^(-1))and a lithium-ion transference number of 0.47 for PVZT.A symmetrical cell using PVZT demonstrates stable Li+deposition/stripping for over 1100 h at a current density of 0.1 mA·cm^(-2).Additionally,a LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2)/Li full cell using PVZT retains 75.0%of its capacity after 1200 cycles at a 2 C rate.This work offers valuable insights into the design of func-tional fillers for CSEs with highly efficient ion transport.展开更多
Solid-state lithium batteries have become a research hotspot in the field of large-scale energy storage due to their excellent safety performance.The development of high-voltage positive electrode materials matched wi...Solid-state lithium batteries have become a research hotspot in the field of large-scale energy storage due to their excellent safety performance.The development of high-voltage positive electrode materials matched with lithium metal anode have advanced the energy density of solid-state lithium batteries close to or even exceeding that of lithium batteries based on a liquid electrolyte,which is expected to be commercialized in the future.However,in high voltage conditions(>4.3 V),the decomposition of electrolyte components,structural degradation,and interface side reactions significantly reduce battery performance and hinder its further development.This review summarizes the latest research progress of inorganic electrolytes,polymer electrolytes,and composite electrolytes in high-voltage solid-state lithium batteries.At the same time,the designs of high-voltage polymer gel electrolyte and high-voltage quasi solid-state electrolyte are introduced in detail.In addition,interface engineering is crucial for improving the overall performance of high-voltage solid-state batteries.Finally,we highlight the challenges faced by high-voltage solid-state lithium batteries and put forward our own views on future research directions.This review offers instructive insights into the advancement of high-voltage solid-state lithium batteries for large-scale energy storage applications.展开更多
基金supported by Program for Changjiang Scholars and Innovative Research Team in University(PCSIRT)(IRT1146)the Program of Research Innovation for University Graduate Students of Jiangsu Province(CXLX13_408)the Priority Academic Development Program of Jiangsu Higher Education Institutions,P.R.China
文摘Sm0.2Ce0.8O1.9 （SDC） electrolyte was prepared by a modified solid state method at relatively low sintering temperatures without any sintering promoters. The phase composition and microstructure of the electrolytes were investigated by X-ray diffraction （XRD） and field emission scanning electron microscopy （FESEM） technologies. A relative density of SDC electrolyte sintered at 1300 ℃ reached 97.3%and the mean SDC grain size was about 770 nm. Their ionic conductivity and thermal expansion coefficient were also measured by electrochemical workstation and dilatometer. The electrolyte attained a high conductivity of 5×10^-2 S/cm at 800 ℃ with an activation energy of 1.03 eV and a proper thermal expansion coefficient of 12.6×10^-6 K^-1.
基金This research was supportedby a grant under‘Development of Key Materials and Fundamental Tech-nology for Secondary Battery’Program of the Ministry of Commerce,Industry and Energy,Korea.
文摘Employing Li2CO3, NiO, Co3O4, and MnCO3 powders as starting materials, Li[Ni1/3Co1/3Mn1/3]O2 was synthesized by solid-state reaction method. Various grinding aids were applied during milling in order to optimize the synthesis process. After successive heat treatments at 650 and 950 ℃, the prepared powders were characterized by X-ray diffraction (XRD) analysis, scanning electron microscopy, and transmission electron microscopy. The powders prepared by adding salt (NaCl) as grinding aid exhibit a clear R3m layer structure. The powders by other grinding aids like heptane show some impurity peaks in the XRD pattern. The former powders show a uniform particle size distribution of less than 1 μm average size while the latter shows a wide distribution ranging from 1 to 10 μm. Energy dispersive X-ray (EDX) analysiss show that the ratio of Ni, Co, and Mn content in the powder is approximately 1/3, 1/3, and 1/3, respecively. The EDX data indicate no incorporation of sodium or chlorine into the powders. Charge-discharge tests gave an initial discharge capacity of 160 mAh·g-1 for the powders with NaCl addition while 70 mAh·g-1 for the powders with heptane.
基金financially supported by the National Key Research and Development Program(2022YFE0127400)the National Natural Science Foundation of China(52172040,52202041,and U23B2077)+1 种基金Taishan Scholar Project of Shandong Province(tsqn202211086,ts202208832,tsqnz20221118)the Fundamental Research Funds for the Central Universities(23CX06055A).
文摘Micro silicon(mSi)is a promising anode candidate for all-solid-state batteries due to its high specific capacity,low side reactions,and high tap density.However,silicon suffers from its poor electronic and ionic conductivity,which is particularly severe on a micro scale and in solid-state systems,leading to increased polarization and inferior electrochemical performance.Doping can broaden the transmission pathways and reduce the diffusion energy barrier for electrons and lithium ions.However,achieving effective,uniform doping in mSi is challenging due to its longer diffusion paths and higher energy barriers.Therefore,current doping research is primarily limited to nanosilicon.In this study,we successfully used a Joule-heating activated staged thermal treatment to achieve full-depth doping of germanium(Ge)in the mSi substrate.The Joule-heating process activated the mSi substrate,resulting in abundant vacancy defects that reduced the diffusion barrier of Ge into the silicon lattice and facilitated full-depth Ge doping.Surprisingly,the resulting Si-Ge anode exhibited significantly enhanced electrical conductivity(70 times).Meanwhile,the improved Li-ion conductivity in mSi and the reduced Young’s modulus enhance the electrode reaction kinetics and integrity after cycling.Ge-doped silicon anodes demonstrate excellent electrochemical performance when applied in sulfide solid-state half-cells and full-cells.This work provides substantial insights into the rational structural design of mSi alloyed anode materials,paving the way for the development of high-performance solid-state Li-ion batteries.
基金supported by the National Natural Science Foundation of China(No.42272044)the High-performance Computing Platform of China University of Geosciences Beijing。
文摘Polyethylene oxide(PEO)-based solid polymer electrolytes(SPEs)have long faced limitations due to low ionic conductivity at ambient temperature and poor interfacial stability with lithium metal anodes.Here,we present a structural engineering strategy to address these challenges through shear-induced crystallization of concentrated PEO-LiTFSI solutions,which self-assemble into flower-like spherulites with radially aligned lamellar crystals.This unique structure creates continuous Li^(+)transport highways through densely packed crystalline domains,achieving a record-high ionic conductivity of 1.70×10^(-4) S/cm at 25℃ for pristine PEO-based systems.Strategic incorporation of lithium montmorillonite(MMTli,10 wt%)further optimizes the composite electrolyte,balancing high ionic conductivity(1.47×10^(-4) S/cm)with enhanced electrochemical stability(4.99 V vs.Li^(+)/Li),elevated Li^(+)transference number(0.62),and mechanical robustness.The composite electrolyte enables stable Li plating/stripping over 800 h in symmetric Li||Li cells and powers LiFePO_(4)||Li solid-state batteries with 82%capacity retention after 200 cycles at 0.2 C under ambient conditions.This work pioneers a scalable processing paradigm for crystalline polymer electrolytes,offering new insights into ion transport mechanisms and validating clay minerals as multifunctional additives for next-generation energy storage systems.
文摘All-solid-state batteries(ASSBs)represent a next-generation energy storage technology,offering enhanced safety,higher energy density,and improved cycling stability compared to conventional liquid-electrolyte-based lithium-ion batteries.Understanding and optimizing the complex chemistries and interfaces that underpin ASSB performance present significant challenges from both experimental and modeling perspectives.In particular,atomistic simulations face difficulties in capturing the complex structure,disorder,and dynamic evolution of materials and interfaces under practically relevant conditions.While established methods such as density functional theory and classical force fields have provided valuable insights,some questions remain difficult to address,particularly those involving large system sizes or long timescales.Recently,machine learning interatomic potentials(MLIPs)have emerged as a transformative tool,enabling atomistic simulations at length and time scales that were previously challenging to access with conventional approaches.By delivering near first-principles accuracy with much greater efficiency,MLIPs open new avenues for large-scale,long-timescale,and high-throughput simulations of solid-state battery materials.In this review,we present a comparative overview of density functional theory,classical force fields,and MLIPs,highlighting their respective strengths and limitations in ASSB research.We then discuss how MLIPs enable simulations that reach longer timescales,larger system sizes,and support high-throughput calculations,providing unique insights into ion transport and interfacial evolution in ASSBs.Finally,we conclude with a summary and outlook on current challenges and future opportunities for expanding MLIP capabilities and accelerating their impact in solid-state battery research.
基金the National Natural Science Foundation of China (52076076, 52006065)Fundamental Research Funds for Central Universities (2025JC003)Beijing Municipal Natural Science Foundation (3242022)
文摘In the realm of large-scale power system energy storage,sodium-based batteries represent a cost-effective post-lithium energy storage technology,making inorganic solid-state sodium batteries(ISSSB)a critical branch of this development.Inorganic solid-state electrolytes(ISSEs)are the core components of sodium batteries;however,they face significant challenges such as insufficient ionic conductivity,interfacial instability,and dendrite growth,all of which severely hinder practical application.This review critically assesses experimental protocols and theoretical frameworks related to mainstream ISSEs and systematizes optimization strategies aimed at overcoming these challenges.Leveraging integrated insights from both experimental and computational studies,the review first categorizes and summarizes the primary types of ISSEs,namely oxide-,sulfide-,and halide-based electrolytes.It then details interfacial optimization strategies focused on addressing three core interfacial issues:ion transport barriers resulting from mechanical incompatibility,side reactions stemming from electrochemical mismatch,and dendrite formation.Finally,the review advocates prioritizing in-depth research that integrates experimental and theoretical approaches to establish a closed-loop methodology encompassing predictive design,multiscale investigation,mechanistic exploration,and high-throughput automated experimentation,with feedback-driven refinement.This work serves as a comprehensive reference and systematic roadmap for future research on solid-state electrolytes(SSEs).
基金financially supported by the National Natural Science Foundation of China(Nos.52263010 and 52372188)2023 Introduction of studying abroad talent program,Henan Provincial Key Scientific Research Project of Collegesand Universities(No.23A150038)+1 种基金Key Scientific Research Project of Education Department of Henan Province(No.22A150042)the National students'platform for innovation and entrepreneurship training program(No.201910476010).
文摘Thermoplastic polyurethane(TPU)consists of a hardsegment and a soft segment,where the former affords mechanical strength and thermalstability,while the latter provides a possibility of good ionic conductivity by promoting dissociation of ions from the lithium salt.Thus,TPU attracts a wide interest recently as a promising polymer electrolyte for solid-state lithium batteries.However,the relatively low ionic conductivity of TPU still restricts its actual applications due to the aggregation of polymer chains,which greatly reduces the dissociation of lithium salts.Herein,a strategy to address this challenge was adopted by in situ polymerization poly(ethylene glycol diacrylate)(PEGDA)in fully dispersed TPU.Hence a stretchable solid-state electrolyte(denoted as TELL and the contrast sample was denoted as TLL)with high ionic conductivity of 7.18×10^(-4) S/cm was obtained at room temperature.The Li^(+)transference number is 0.85 in Li|TELL|Li cell and can stably undergo charge-discharge cycles for 1400 h at a current density of O.1 mA/cm^(2),while the contrast sample is short-circuited after 634 h of cycling.The LiFePO_(4)|TELL|Li cell achieves a capacity retention of 78.93%after 200 cycles at 2 C.The LiFePO_(4) TLL Li cellonly gains the capacity retention of 51.9%after 50 cyclesat the same current density.So,the method adopted here may provide a new approach to realize a flexible solid-state electrolyte with high ion-conductivity.
基金supported by the National Natural Science Foundation of China(grant number:22274050)the Shanghai Science and Technology Commission(contract number:23J21900300)the Fundamental Research Funds for the Central Universities.
文摘Ribonucleic acid(RNA)structures and dynamics play a crucial role in elucidating RNA functions and facilitating the design of drugs targeting RNA and RNA-protein complexes.However,obtaining RNA structures using conventional biophysical techniques,such as Xray crystallography and solution nuclear magnetic resonance(NMR),presents challenges due to the inherent flexibility and susceptibility to degradation of RNA.In recent years,solid-state NMR(SSNMR)has rapidly emerged as a promising alternative technique for characterizing RNA structure and dynamics.SSNMR has several distinct advantages,including flexibility in sample states,the ability to capture dynamic features of RNA in solid form,and suitability to character RNAs in various sizes.Recent decade witnessed the growth of ^(1)H-detected SSNMR methods on RNA,which targeted elucidating RNA topology and base pair dynamics in solid state.They have been applied to determine the topology of RNA segment in human immunodeficiency virus(HIV)genome and the base pair dynamics of riboswitch RNA.These advancements have expanded the utility of SSNMR techniques within the RNA research field.This review provides a comprehensive discussion of recent progress in ^(1)H-detected SSNMR investigations into RNA structure and dynamics.We focus on the established ^(1)H-detected SSNMR methods,sample preparation protocols,and the implementation of rapid data acquisition approaches.
基金supported by the Science and Technology Development Fund(FDCT)of Macao SAR(No.0110/2023/AMJ)Innovation Support Plan,Hong Kong,Macao and Taiwan Science and Technology Cooperation Project of Jiangsu Province(No.BZ2022047)+1 种基金National Key Research and Development Program of China(2023YFE0205300)the Joint Fund of Ba-sic and Applied Basic Research Fund of Guangdong Province(No.2021B1515130009).
文摘An approach called hybrid heat-source solid-state additive manufacturing (HHSAM) for fabricating multilayer AA6061 deposition with superior properties is proposed in this paper. As compared with the traditional additive friction stir deposition (AFSD), the auxiliary induction heat-source in HHSAM effectively improves the temperature and fluidity of plastic flow, which facilitates the formation and enrichment of residual Mg_(2)Si phases besides Al(Fe,Mn)Si, promotes the dynamic recrystallization and increases the bonding strength between layers during the deposition process. Therefore, the HHSAM depositions possess a more uniform structure, superior integral mechanical properties and corrosion resistance after heat treatment process. Moreover, HHSAMed specimens avoid abnormal grain growth (AGG) in heat treatment process, which is regularly encountered in the traditional AFSD. HHSAM method is proved to be a new solid-state additive manufacturing method with good developing prospects for fabricating alloy production with excellent properties in a high-efficiency manner.
基金supported by the National Key Technology R&D Program (Nos. 2012BAC02B01, 2012BAC12B05, 2011BAE13B07, and 2011BAC10B02)the National High Technology Research and Development Program of China (No. 2012AA063202)+2 种基金the National Natural Science Foundation of China (Nos. 51174247 and 51004011)the Science and Technology Program of Guangdong Province, China (No. 2010A030200003)the Ph.D. Programs Foundation of the Ministry of Education of China (No. 2010000612003)
文摘Oily cold rolling mill （CRM） sludge is one of the pollutants emitted by iron and steel plants. Recycling oily CRM sludge can not only reduce pollution but also bring social and environmental benefits. In this study, using oily CRM sludge as sources of iron oxide, the strontium ferrite powders were synthesized in multiple steps including vacuum distillation, magnetic separation, oxidizing roasting, and solidstate reaction. The optimal technological conditions of vacuum distillation and oxidizing roasting were studied carefully. To consider the effects of Fe203/ SrCO3 tool ratio, calcination temperature, milling time and calcination time on magnetic properties of prepared strontium ferrite powders, the orthogonal experimental method was adopted. The maximum saturation magneti- zation （62.6 mA-m2.g-1） of the synthesized strontium ferrite powders was achieved at the Fe203/SrCO3 mol ratio of 6, 5 h milling time, 1250 ~C calcination temperature, and 1 h calcination time. Strontium ferrite powders syn- thesis method not only provides a cheap, high quality raw material for the production of strontium ferrite powders, but also effectively prevents the environmental pollution.
文摘This study shows that sulfide solid-state electrolytes,β-Li_(3)PS_(4)and Li_(6)PS_(5)Cl,are flammable solids.Both solid-state electrolytes release sulfur vapor in a dry,oxidizing environment at elevated temperature<300℃.Sulfur vapor is a highly flammable gas,which then auto-ignites to produce a flame.This behavior suggests that an O_(2)-S gas-gas reaction mechanism may contribute to all-solid-state battery thermal runaway.To improve all-solid-state battery safety,current work focuses on eliminating the O_(2)source by changing the cathode active material.The conclusion of this study suggests that all-solidstate battery safety can also be realized by the development of solid-state electrolytes with less susceptibility to sulfur volatilization.
基金supported by the National Natural Science Foundation of China(Nos.52174277 and 51874077)the Fundamental Funds for the Central Universities,China(No.N2225032)+1 种基金the China Postdoctoral Science Foundation(No.2022M720683)the Postdoctoral Fund of Northeastern University,China。
文摘The formation mechanism of calcium vanadate and manganese vanadate and the difference between calcium and manganese in the reaction with vanadium are basic issues in the calcification roasting and manganese roasting process with vanadium slag.In this work,CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples were prepared and roasted for different time periods to illustrate and compare the diffusion reaction mechanisms.Then,the changes in the diffusion product and diffusion coefficient were investigated and calculated based on scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS) analysis.Results show that with the extension of the roasting time,the diffusion reaction gradually proceeds among the CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples.The regional boundaries of calcium and vanadium are easily identifiable for the CaO–V_(2)O_(5) diffusion couple.Meanwhile,for the MnO_(2)–V_(2)O_(5) diffusion couple,MnO_(2) gradually decomposes to form Mn_(2)O_(3),and vanadium diffuses into the interior of Mn_(2)O_(3).Only a part of vanadium combines with manganese to form the diffusion production layer.CaV_(2)O_(6) and MnV_(2)O_(6) are the interfacial reaction products of the CaO–V_(2)O_(5) and MnO_(2)–V_(2)O_(5) diffusion couples,respectively,whose thicknesses are 39.85 and 32.13μm when roasted for 16 h.After 16 h,both diffusion couples reach the reaction equilibrium due to the limitation of diffusion.The diffusion coefficient of the CaO–V_(2)O_(5) diffusion couple is higher than that of the MnO_(2)–V_(2)O_(5) diffusion couple for the same roasting time,and the diffusion reaction between vanadium and calcium is easier than that between vanadium and manganese.
基金financially supported by the National Natural Science Foundation of China(Nos.22102212 and 22479067).
文摘High-nickel ternary cathodes hold a great application prospect in solid-state lithium metal batteries to achieve high-energy density,but they still suffer from structural instability and detrimental side reactions with the solid-state electrolytes.To circumvent these issues,a continuous uniform layer polyacrylonitrile(PAN)was introduced on the surface of LiNi_(0.8)Mn_(0.1)Co_(0.1)O_(2) via in situ polymerization of acrylonitrile(AN).Furthermore,the partial-cyclized treatment of PAN(cPAN)coating layer presents high ionic and electron conductivity,which can accelerate interfacial Li+and electron diffusion simultaneously.And the thermodynamically stabilized cPAN coating layer cannot only effectively inhibit detrimental side reactions between cathode and solid-state electrolytes but also provide a homogeneous stress to simultaneously address the problems of bulk structural degradation,which contributes to the exceptional mechanical and electrochemical stabilities of the modified electrode.Besides,the coordination bond interaction between the cPAN and NCM811 can suppress the migration of Ni to elevate the stability of the crystal structure.Benefited from these,the In-cPAN-260@NCM811 shows excellent cycling performance with a retention of 86.8%after 300 cycles and superior rate capability.And endow the solid-state battery with thermal safety stability even at hightemperature extreme environment.This facile and scalable surface engineering represents significant progress in developing high-performance solid-state lithium metal batteries.
基金the financial support from the National Key R&D Program of China (Grant No. 2021YFB3800300)the supports from National Key R&D Program of China (Grant No. 2022YFB3807700)+6 种基金the National Natural Science Foundation of China (Grant No. U20A20248)the supports from the National Natural Science Foundation of China (Grant Nos. W2441017, 22409103)the “Innovation Yongjiang 2035” Key R&D Program (Grant Nos. 2024Z040, 2025Z063)the National Key R&D Program of China (Grant No. 2023YFC2812700)the Natural Science Foundation of Shandong Province (Grant No. ZR2024YQ008)funding supports from the National Key R&D Program of China (Grant No. 2021YFB3800300)science and technology innovation fund for emission peak and carbon neutrality of Jiangsu province (Grant Nos. BK20220034, BK20231512)。
文摘With the widespread adoption of lithium-ion batteries(LIBs),safety concerns associated with flammable organic elec-trolytes have become increasingly critical.Solid-state lithium batteries(SSLBs),with enhanced safety and higher energy density potential,are regarded as a promising next-generation energy storage technology.However,the practical appli-cation of solid-state electrolytes(SSEs)remains hindered by several challenges,including low Li^(+)ion conductivity,poor interfacial compatibility with electrodes,unfavorable mechanical properties and difficulties in scalable manufacturing.This review systematically examines recent progress in SSEs,including inorganic types(oxides,sulfides,halides),organic types(polymers,plastic crystals,poly(ionic liquids)(PILs)),and the emerging class of soft solid-state electrolytes(S3Es),especially those based on“rigid-flexible synergy”composites and“Li+-desolvation”mechanism using porous frameworks.Critical assessment reveals that single-component SSEs face inherent limitations that are difficult to be fully overcome through compositional and structural modification alone.In contrast,S3Es integrate the strength of complementary components to achieve a balanced and synergic enhancement in electrochemical properties(e.g.,ionic conductivity and stability window),mechanical integrity,and processability,showing great promise as next-generation SSEs.Furthermore,the application-ori-ented challenges and emerging trends in S3E research are outlined,aiming to provide strategic insights into future develop-ment of high-performance SSEs.
基金supported by King Mongkut’s Institute of Technology Ladkrabang [KREF146001]
文摘Three individual peaks of thermal solid-state reaction processes of the synthesized Mn0.90Co0.05Mg0.05HPO4?3H2O were observed corresponding to dehydration I,dehydration II and polycondensation processes.An alternative method for the calculation of the extent of conversion was proposed from the peak area of the individual DTG peak after applying the best fitting deconvolution function(Frazer–Suzuki function).An iterative integral isoconversional equation was used to compute the values of the apparent activation energy Eαand they were found to be 65.87,78.16 and 119.32 kJ/mol for three peaks,respectively.Each individual peak was guaranteed to be a single-step kinetic system with its unique kinetic parameters.The reaction mechanism functions were selected by the comparison between experimental and model plots.The results show that the first,second and final individual peaks were two-dimensional diffusion of spherical symmetry(D2),three-dimensional diffusion of spherical symmetry(D3)and contracting cylinder(cylindrical symmetry,R2)mechanisms.Pre-exponential factor values of 3.91×106,1.35×107 and 2.15×107 s?1 were calculated from the Eαvalues and reaction mechanisms.The corresponded standard thermodynamic functions of the transition-state(activated)complexes were determined and found to agree well with the experimental data.
基金supported by the National Natural Science Foundation of China(Nos.22171102 and 22090044)the National Key R&D Program of China(Nos.2021YFF0500502 and 2023YFA1506304)+2 种基金the Jilin Province Science and Technology Development Plan(No.20230101024JC)the"Medicine+X"crossinnovation team of Bethune Medical Department of Jilin University"Leading the Charge with Open Competition"construction project(No.2022JBGS04)the Jilin University Graduate Training Office(Nos.2021JGZ08 and 2022YJSJIP20).
文摘Solid-state electrolytes(SSEs),as the core component within the next generation of key energy storage technologies-solid-state lithium batteries(SSLBs)-are significantly leading the development of future energy storage systems.Among the numerous types of SSEs,inorganic oxide garnet-structured superionic conductors Li7La3Zr2O12(LLZO)crystallized with the cubic Iaˉ3d space group have received considerable attention owing to their highly advantageous intrinsic properties encompassing reasonable lithium-ion conductivity,wide electrochemical voltage window,high shear modulus,and excellent chemical stability with electrodes.However,no SSEs possess all the properties necessary for SSLBs,thus both the ionic conductivity at room temperature and stability in ambient air regarding cubic garnet-based electrolytes are still subject to further improvement.Hence,this review comprehensively covers the nine key structural factors affecting the ion conductivity of garnet-based electrolytes comprising Li concentration,Li vacancy concentration,Li carrier concentration and mobility,Li occupancy at available sites,lattice constant,triangle bottleneck size,oxygen vacancy defects,and Li-O bonding interactions.Furthermore,the general illustration of structures and fundamental features being crucial to chemical stability is examined,including Li concentration,Li-site occupation behavior,and Li-O bonding interactions.Insights into the composition-structure-property relations among cubic garnet-based oxide ionic conductors from the perspective of their crystal structures,revealing the potential compatibility conflicts between ionic transportation and chemical stability resulting from Li-O bonding interactions.We believe that this review will lay the foundation for future reasonable structural design of oxide-based or even other types of superionic conductors,thus assisting in promoting the rapid development of alternative green and sustainable technologies.
基金supported by the National Key R&D Program of China (Grant No.2020YFA0710500)The authors acknowledge the basic scientific research business expenses Program of Xi’an Jiaotong University (Grant No.xzy022022053)the Independent Research Project of the State Key Laboratory of Electrical Insulation and Power Equipment (Grant No.EIPE23303)for financial support.
文摘Safety issues induced by infinite anode volume change and uncontrolled lithium(Li)dendrite growth have become the biggest obstacle to the practical application of Li metal batteries.In addition,the tra-ditional rolling method makes it difficult to manufacture thin Li foil with high mechanical strength and low Li content.Herein,a three-dimensional(3D)lithophilic carbon paper/copper(Cu)current collector hybrid anode with ultra-low Li metal content is prepared by a hot-pressing method.The highly re-versible and stable lithiophilic layer LiC_(x) formed in situ by heating/pressing treatment provides abun-dant nucleation sites and reduces the Li nucleation overpotential,thereby effectively suppressing Li den-drite growth.Moreover,the volume change and pulverization problems of Li metal anode during depo-sition/stripping also can be accommodated by the 3D skeleton.The optimization effect has been directly confirmed by in-situ optical and ex-situ scanning electron microscope observation.Therefore,highly sta-ble performance(158.4 mA h g^(-1) at 2 C after 200 cycles with a capacity retention of 95.24%)in Li@LCP-Cu||NCM811 coin cell can be achieved.Furthermore,the solid-state battery assembled with the hybrid anode,poly(vinylidene fluoride)(PVDF)-based polymer electrolyte and polyethylene oxide(PEO)interface functional layer also exhibits the best electrochemical and safety performance,which also proves that the Li@LCP-Cu anode has great potential for application in solid-state batteries.
基金supported financially by the National Natural Science Foundation of China(No.52172202)Science and Technology Program of Guangzhou,China(No.SL2024A03J00326)+1 种基金Key Research and Development project of High-Level Scientific and Technological Talent Introduction for Luliang City(No.2023RC27)the Basic Research Program(Free Exploration Category)Project for Shanxi Province(No.202303021222251)
文摘Severe structural fractures and persistent side reactions at the interface with liquid electrolytes have hindered the commercialization of silicon(Si)anodes.Solid-state electrolytes present a promising solution to address these issues.However,the high interfacial resistance of rigid ceramic electrolytes and the limited ionic conductivity of polymer electrolytes remain significant challenges,further complicated by the substantial volume expansion of Si.In this work,we chemically grafted a flame-retardant,self-healing polyurethane-thiourea polymer onto Li_(7)P_(3)S_(11)(SHPUSB-40%LPS)via nucleophilic addition,creating an electrolyte with exceptional ionic conductivity,high elasticity,and strong compatibility with Si anodes.We observed that FSI^(-)was strongly adsorbed onto the LPS surface through electrostatic interactions with sulfur vacancies,enhancing Li^(+)transport.Furthermore,SHPUSB-40%LPS exhibits dynamic covalent disulfide bonds and hydrogen bonds,enabling self-assembly of the electrolyte at the interface.This dynamic bonding provides a self-healing mechanism that mitigates structural changes during Si expansion and contraction cycles.As a result,the Si anode with SHPUSB-40%LPS presents excellent cycling stability,retaining nearly 53.5%of its capacity after 300 cycles.The practical applicability of this design was validated in a 2 Ah all-solid-state Si‖LiNi_(0.6)Mn_(0.2)Co_(0.2)O_(2)pouch cell,which maintained a stable Li-ion storage capacity retention of 76.3%after 350cycles at 0.5C.This novel solid-state electrolyte with selfhealing properties offers a promising strategy to address fundamental interfacial and performance challenges associated with Si anodes.
基金supported by National Science Fund for Distinguished Young Scholars(Grant No.52325206)National Key Research and Development Program of China(Grant No.2021YFF0500600)+3 种基金National Natural Science Foundation of China(Grant Nos.U2001220 and 52203298)Shenzhen Technical Plan Project(Grant Nos.RCJC20200714114436091,JCYJ20220530143012027,JCYJ20220818101003008,and JCYJ20220818101003007)Tsinghua Shenzhen International Graduate School-Shenzhen Pengrui Young Faculty Program of Shenzhen Pengrui Foundation(Grant No.SZPR2023006)Shenzhen Science and Technology Program(Grant No.WDZC20231126160733001).
文摘Composite solid electrolytes(CSEs)are considered among the most promising candidates for solid-state batteries.However,their practical application is hindered by low ionic conductivity and a limited lithium-ion transference number,primarily owing to the insufficient mobility of Li+.In this work,we design a heterojunc-tion nanoparticle composed of bimetallic zeolitic imidazolate frameworks(ZIFs)coupled with amorphous tita-nium oxide(TiO_(2)@Zn/Co–ZIF)as a filler to fabricate a composite solid-state electrolyte(PVZT).The amor-phous TiO_(2) coating facilitates salt dissociation through Lewis acid–base interactions with the anions of the lithium salt.Meanwhile,the Zn/Co–ZIF framework not only provides additional selective pathways for Li+transport but also effectively restricts anion migration through its confined pore size.The synergistic effect results in a high room-temperature ionic conductivity(8.8×10^(-4) S·cm^(-1))and a lithium-ion transference number of 0.47 for PVZT.A symmetrical cell using PVZT demonstrates stable Li+deposition/stripping for over 1100 h at a current density of 0.1 mA·cm^(-2).Additionally,a LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2)/Li full cell using PVZT retains 75.0%of its capacity after 1200 cycles at a 2 C rate.This work offers valuable insights into the design of func-tional fillers for CSEs with highly efficient ion transport.
基金supported by the National Key R&D Program of China(2024YFA1211100)the National Natural Science Foundation of China(52301278,22479080,52202254,92372001,22393900,and 92372203)+2 种基金the Natural Science Foundation of Jiangsu Province(BK20230937,BK20220966)the Science and Technology Plans of Tianjin(23JCYBJC00170,24JCJQJC00220,and 24ZXZSSS00390)the Fundamental Research Funds for the Central Universities(02063253167,30922010708)。
文摘Solid-state lithium batteries have become a research hotspot in the field of large-scale energy storage due to their excellent safety performance.The development of high-voltage positive electrode materials matched with lithium metal anode have advanced the energy density of solid-state lithium batteries close to or even exceeding that of lithium batteries based on a liquid electrolyte,which is expected to be commercialized in the future.However,in high voltage conditions(>4.3 V),the decomposition of electrolyte components,structural degradation,and interface side reactions significantly reduce battery performance and hinder its further development.This review summarizes the latest research progress of inorganic electrolytes,polymer electrolytes,and composite electrolytes in high-voltage solid-state lithium batteries.At the same time,the designs of high-voltage polymer gel electrolyte and high-voltage quasi solid-state electrolyte are introduced in detail.In addition,interface engineering is crucial for improving the overall performance of high-voltage solid-state batteries.Finally,we highlight the challenges faced by high-voltage solid-state lithium batteries and put forward our own views on future research directions.This review offers instructive insights into the advancement of high-voltage solid-state lithium batteries for large-scale energy storage applications.
