The solid–liquid compound casting of Mg-AZ91D and Ti-TC4 alloys was developed by using pure Ni electro-deposited coating.The pouring temperatures of 660℃,690℃,720℃and 750℃were chosen to investigated the effects o...The solid–liquid compound casting of Mg-AZ91D and Ti-TC4 alloys was developed by using pure Ni electro-deposited coating.The pouring temperatures of 660℃,690℃,720℃and 750℃were chosen to investigated the effects of casting temperatures on microstructural evolution,properties,and fracture behaviors of Ni-coated TC4/AZ91D bimetals by the solid–liquid compound casting(SLCC).The scanning electron microscopy(SEM)and the energy dispersive spectroscopy(EDS)results showed that the interfacial zone mainly composed of nickel,Mg_(2)Ni and Mg-Al-Ni in the bimetals cast at 660℃.As the pouring temperature was increased to 750℃,the width of the interface zone,which mainly composed ofδ(Mg),Mg_(2)Ni,Mg-Al-Ni,Mg_(3)TiNi_(2) and Al_(3)Ni,gradually increased.The microhardness tests showed that the micro-hardness of the interface zone was smaller than that of TC4 substrate but larger than that of the cast AZ91D matrix.At the pouring temperature of 720℃,the Ni-coated TC4/AZ91D bimetals had the most typical homogeneous interface,which had granular Mg-Al-Ni ternary phase but no ribbon-like Al3Ni binary phase,and achieved the highest shear strength of 97.35MPa.Meanwhile,further fracture behavior analysis showed that most fracture failure of Ni-coated TC4/AZ91D bimetals occurred at the Mg_(2)Ni+δ(Mg)eutectic structure and Al_(3)Ni hard intermetallic.展开更多
The paper presents a novel material preparation technology—Solid liquid mixed casting technology. In the technology, large amounts of homogeneous alloy powder or heterogenous powder with perfect wettability are added...The paper presents a novel material preparation technology—Solid liquid mixed casting technology. In the technology, large amounts of homogeneous alloy powder or heterogenous powder with perfect wettability are added into the superheated melt. After strong agitation, the mixed melt can be cast or hot processed. Applying solid liquid mixed casting, three kinds of Al Si alloys were investigated. The results show that, when the mass of powder accession to alloy melt is about 1, the mean size of primary Si in hyper eutectic alloy can be controlled at less than 5 μm; and the mean grain size of α phase in hypo eutectic alloy is less than 10 μm. This technology has the advantage of preparing material with very fine microstructure by fairly simple casting process, and may be a new practicable and valuable metal preparation technology.展开更多
Whether the particle will be trapped by the solid-liquid interface or not is dependent on its moving behavior ahead of the interface, so a mathematical model has been developed to investigate the movement of the parti...Whether the particle will be trapped by the solid-liquid interface or not is dependent on its moving behavior ahead of the interface, so a mathematical model has been developed to investigate the movement of the particle ahead of the solid-liquid interface. Based on the theory for the boundary layer, the fluid velocity field near the solid-liquid interface was obtained, and the trajectories of particles were calculated by the equations of motion for particles. In this model, the drag force, the added mass force, the buoyance force, the gravitational force, the Saffman force and the Basset history force are considered. The results show that the behavior of the particle ahead of the solid-liquid interface is affected by the physical property of the particle and fluid flow. And in the continuous casting process, if it moves in the stream directed upward or downward near vertical solid-liquid interface or in the horizontal flow under the solid-liquid interface, the particle with the diameter from 5 um to 60um can reach the solid-liquid interface. But if it moves in horizontal flow above the solid-liquid interface, only the particle with the diameter from 5 um to 10 um can reach the solid-liquid interface.展开更多
Velocities of solid phase and liquid phase in debris flow are one key problem to research on impact and abrasion mechanism of banks and control structures under action of debris flow. Debris flow was simplified as two...Velocities of solid phase and liquid phase in debris flow are one key problem to research on impact and abrasion mechanism of banks and control structures under action of debris flow. Debris flow was simplified as two-phase liquid composed of solid phase with the same diameter particles and liquid phase with the same mechanical features. Assume debris flow was one-dimension two-phase liquid moving to one direction, then general equations of velocities of solid phase and liquid phase were founded in two-phase theory. Methods to calculate average pressures, volume forces and surface forces of debris flow control volume were established. Specially, surface forces were ascertained using Bingham＇s rheology equation of liquid phase and Bagnold＇s testing results about interaction between particles of solid phase. Proportional coefficient of velocities between liquid phase and solid phase was put forward, meanwhile, divergent coefficient between theoretical velocity and real velocity of solid phase was provided too. To state succinctly before, method to calculate velocities of solid phase and liquid phase was obtained through solution to general equations. The method is suitable for both viscous debris flow and thin debris flow. Additionally, velocities every phase can be identified through analyzing deposits in-situ after occurring of debris flow. It is obvious from engineering case the result in the method is consistent to that in real-time field observation.展开更多
Extended finite element method(XFEM) is proposed to simulate the discontinuous interface in the liquid-solid forming process.The discontinuous interface is an important phenomenon happening in the liquid-solid forming...Extended finite element method(XFEM) is proposed to simulate the discontinuous interface in the liquid-solid forming process.The discontinuous interface is an important phenomenon happening in the liquid-solid forming processes and it is difficult to be simulated accurately with conventional finite element method(CFEM) because it involves solid phase and liquid phase simultaneously.XFEM is becoming more and more popular with the need of solving the discontinuous problem happening in engineering field.The implementation method of XFEM is proposed on Abaqus code by using UEL(user element) with the flowchart.The key is to modify the element stiffness in the proposed method by using UEL on the platform of Abaqus code.In contrast to XFEM used in the simulation of solidification,the geometrical and physical properties of elements were modified at the same time in our method that is beneficial to getting smooth interface transition and precise analysis results.The analysis is simplified significantly with XFEM.展开更多
A funnel-type mold is commonly used to provide necessary clearance for the submerged entry nozzle in the thin slab casting(TSC).The partially solidified shell is subjected to the mechanical deformations,which can lead...A funnel-type mold is commonly used to provide necessary clearance for the submerged entry nozzle in the thin slab casting(TSC).The partially solidified shell is subjected to the mechanical deformations,which can lead to the defects formation and,as a results,to a breakout.Traditionally,the results of the flow simulation,performed by the finite volume method(FVM),are fed to the external package for the finite element analysis of stress and strain.A coupled model was assembled using“creeping solid”approach by blending the Norton-Hoff viscoplastic stress for the solidifying shell with the Newtonian viscous stress of the liquid melt.The FVM was used to combine both liquid and solid stress models within a single solver.The iterative procedure based on the improved both side diffusion method was introduced to treat the nonlinear relation between the viscoplastic stress and the strain rate.The modeled shell thickness was verified by previously published breakout measurements and the simulation results.Temperature distribution,obtained during the TSC simulation,dominantly corresponds to the viscoplastic range.Developed numerical approach is robust and has direct industrial application.展开更多
To explore the complex thermal-mechanical-chemical behavior in the solid-liquid cast-roll bonding(SLCRB) of Cu/Al cladding strip, numerical simulations were conducted from both macro and micro scales. In macro-scale, ...To explore the complex thermal-mechanical-chemical behavior in the solid-liquid cast-roll bonding(SLCRB) of Cu/Al cladding strip, numerical simulations were conducted from both macro and micro scales. In macro-scale, with birth and death element method, a thermo-mechanical coupled finite element model(FEM) was set up to explore the temperature and contact pressure distribution at the Cu/Al bonding interface in the SLCRB process. Taking these macro-scale simulation results as boundary conditions, we simulated the atom diffusion law of the bonding interface by molecular dynamics(MD) in micro-scale. The results indicate that the temperature in Cu/Al bonding interface deceases from 700 to 320 ℃ from the entrance to the exit of caster, and the peak of contact pressure reaches up to 140 MPa. The interfacial diffusion thickness depends on temperature and rolling reduction, higher temperature results in larger thickness, and the rolling reduction below kiss point leads to significant elongation deformation of cladding strip which yields more newborn interface with fresh metal and make the diffusion layer thinner. The surface roughness of Cu strip was found to be benefit to atoms diffusion in the Cu/Al bonding interface. Meanwhile, combined with the SEM-EDS observation on the microstructure and composition in the bonding interface of the experimental samples acquired from the castrolling bite, it is revealed that the rolling reduction and severe elongation deformation in the solid-solid contact zone below kiss point guarantee the satisfactory metallurgical bonding with thin and smooth diffusion layer. The bonding mechanisms of reactive diffusion, mechanical interlocking and crack bonding are proved to coexist in the SLCRB process.展开更多
Particle based methods can be used for both the simulations of solid and fluid phases in multiphase medium, such as the discrete-element method for solid phase and the smoothed particle hydrodynamics for fluid phase. ...Particle based methods can be used for both the simulations of solid and fluid phases in multiphase medium, such as the discrete-element method for solid phase and the smoothed particle hydrodynamics for fluid phase. This paper presents a computational method combining these two methods for solid-liquid medium. The two phases are coupled by using an improved model from a reported Lagrangian-Eulerian method. The technique is verified by simulating liquid-solid flows in a two-dimensional lid-driven cavity.展开更多
Rheocasting with semi-solid slurry has been widely used in industrial processes in recent years.The Cup-Cast method is one of the most effective ways to produce semi-solid slurry for rheocasting.In order to study the ...Rheocasting with semi-solid slurry has been widely used in industrial processes in recent years.The Cup-Cast method is one of the most effective ways to produce semi-solid slurry for rheocasting.In order to study the effect of electromagnetic stirring on the fabrication of semi-solid slurry,we have applied the Double-Axis-Electromagnetic Stirrer(DAEMS)to the Cup-Cast method.Microstructure of the slurry was observed by an optical microscope and Electron Back-Scatter Patterns(EBSP).The results indicated that the electromagnetic stirrer made it possible to accelerate the cooling rate of the melt,thus resulting in a higher quality slurry.展开更多
Thin-slab continuous casting and rolling technology is a process integrating casting and plastic deformation. In this study,targeting actions such as slab deformation and liquid core flows during the process of liquid...Thin-slab continuous casting and rolling technology is a process integrating casting and plastic deformation. In this study,targeting actions such as slab deformation and liquid core flows during the process of liquid core reduction on thin-slab continuous casting, suggests the fluid-solid coupling method should be used to research the characteristic and patterns of slab deformation during the liquid core reduction process, as well as research liquid core backflows. A material model of the slab shell was obtained through the high-temperature compression test of the cast steel. The analysis of the fluid-solid coupling simulation for liquid core reduction shows that slab deformation concentrates on the narrow side due to the existence of the liquid core. Meanwhile,the stress and strain increases with the increase of the reduction rate and slab thickness. The changing trends of stress and strain are identical under various conditions. The results demonstrate that using greater reduction at the upper part of the slab, which has a higher temperature and thinner slab,is beneficial to the quality of the slab. Moreover,the liquid core is extruded as the reduction is implemented. The quantity of the extrusion increases with the increase of reduction rate and the thickness of thinner shell, which leads to fluctuation of the mould level, making the operation more difficult.展开更多
This paper employs the integral-averaged method of thickness to approximate the periodical flows in a piezoelectric micropump, with a shallow water equation including nonlinearity and viscous damp presented to charact...This paper employs the integral-averaged method of thickness to approximate the periodical flows in a piezoelectric micropump, with a shallow water equation including nonlinearity and viscous damp presented to characterize the flows in micropump. The finite element method is used to obtain a matrix equation of fluid pressure. The fluid pressure equation is combined with the vibration equation of a silicon diaphragm to construct a liquid-solid coupled equation for reflecting the interaction between solid diaphragm and fluid motion in a micropump. Numerical results of a mode analysis of the coupled system indicate that the natural frequencies of the coupled system are much lower than those of the non-coupled system. The influence of additional mass and viscous damp of fluid on the natural frequencies of the coupled system is more significant as the pump thickness is small. It is found that the vibration shape functions of silicon diaphragm of the coupled system are almost the same as those of the non-coupled system. This paper also gives the first-order amplitude-frequency relationship of the silicon diaphragm, which is necessary for the flow-rate-frequency analysis of a micropump.展开更多
Model experiments with low melting point liquid metals are an important tool to investigate the flow structure and related transport processes in melt flows relevant for metallurgical applications.We present the new e...Model experiments with low melting point liquid metals are an important tool to investigate the flow structure and related transport processes in melt flows relevant for metallurgical applications.We present the new experimental facility LIMMCAST for modelling the continuous casting process of steel using the alloy SnBi at temperatures of 200-400℃.The parameters of the facility and the dimensions of the test sections will be given,and the possibilities for flow investigations in tundish,submerged entry nozzle and mould will be discussed.In addition,the smaller set-up Mini-LIMMCAST will be presented,which works with the room-temperature liquid alloy GaInSn.The main value of cold metal laboratory experiments consists in the capabilities to obtain quantitative flow measurements with a reasonable spatial and temporal resolution.New ultrasonic and electromagnetic techniques for measuring the velocity in liquid metal flows came up during the last decade allowing for a satisfying characterisation of flow quantities in the considered temperature range up to 400℃.First results from LIMMCAST and Mini-LIMMCAST will be presented covering the following phenomena:fully contacfless electromagnetic tomography of the flow in the mould,flow monitoring by a multitude of ultrasonic sensors,and analysis of the flow in the mould under the influence of an electromagnetic brake: intensification of the flow turbulence contrary to the expected flow damping,injection of argon bubbles through the stopper rod:occurrence of pressure oscillations.展开更多
The isothermal single-component multi-phase lattice Boltzmann method(LBM)combined with the particle motion model is used to simulate the detailed process of liquid film rupture induced by a single spherical particle.T...The isothermal single-component multi-phase lattice Boltzmann method(LBM)combined with the particle motion model is used to simulate the detailed process of liquid film rupture induced by a single spherical particle.The entire process of the liquid film rupture can be divided into two stages.In Stage 1,the particle contacts with the liquid film and moves into it due to the interfacial force and finally penetrates the liquid film.Then in Stage 2,the upper and lower liquid surfaces of the thin film are driven by the capillary force and approach to each other along the surface of the particle,resulting in a complete rupture.It is found that a hydrophobic particle with a contact angle of 106.7°shows the shortest rupture duration when the liquid film thickness is less than the particle radius.When the thickness of the liquid film is greater than the immersed depth of the particle at equilibrium,the time of liquid film rupture caused by a hydrophobic particle will be increased.On the other hand,a moderately hydrophilic particle can form a bridge in the middle of the liquid film to enhance the stability of the thin liquid film.展开更多
In the paper, 3-D analysis method with unitive schemes is set up, which is used to resolve the uplift with multiple moving boundaries and multiple nonlinear coupling for anchored liquid storage tanks. hi it, an algori...In the paper, 3-D analysis method with unitive schemes is set up, which is used to resolve the uplift with multiple moving boundaries and multiple nonlinear coupling for anchored liquid storage tanks. hi it, an algorithm of quasi-harmonious finite elements for arbitrary quadrilateral of thin plates and shells is built up to analyze the multiple coupling problems of general thin plates and shells structures with three dimensions, the complementary equations for analyzing uplifting moving boundary problems are deduced. The axial symmetry and presumption of beam type mode are not used. In it, an algorithm is put forward for analyzing the Navier-Stokes problems of unsteady, three-dimensional, and viscous liquid with sloshing of moving boundary surfaces in large amplitude under ALE frame by scheme of time-split-steps to which linear potential theory is not applied. The algorithms can be used to analyze the solid-liquid multiple nonlinear coupling problems with 3-D moving boundary with friction in multiple places.展开更多
基金The authors would like to acknowledge the financial supports from the National Natural Science Foundation of China(No.51875062).
文摘The solid–liquid compound casting of Mg-AZ91D and Ti-TC4 alloys was developed by using pure Ni electro-deposited coating.The pouring temperatures of 660℃,690℃,720℃and 750℃were chosen to investigated the effects of casting temperatures on microstructural evolution,properties,and fracture behaviors of Ni-coated TC4/AZ91D bimetals by the solid–liquid compound casting(SLCC).The scanning electron microscopy(SEM)and the energy dispersive spectroscopy(EDS)results showed that the interfacial zone mainly composed of nickel,Mg_(2)Ni and Mg-Al-Ni in the bimetals cast at 660℃.As the pouring temperature was increased to 750℃,the width of the interface zone,which mainly composed ofδ(Mg),Mg_(2)Ni,Mg-Al-Ni,Mg_(3)TiNi_(2) and Al_(3)Ni,gradually increased.The microhardness tests showed that the micro-hardness of the interface zone was smaller than that of TC4 substrate but larger than that of the cast AZ91D matrix.At the pouring temperature of 720℃,the Ni-coated TC4/AZ91D bimetals had the most typical homogeneous interface,which had granular Mg-Al-Ni ternary phase but no ribbon-like Al3Ni binary phase,and achieved the highest shear strength of 97.35MPa.Meanwhile,further fracture behavior analysis showed that most fracture failure of Ni-coated TC4/AZ91D bimetals occurred at the Mg_(2)Ni+δ(Mg)eutectic structure and Al_(3)Ni hard intermetallic.
文摘The paper presents a novel material preparation technology—Solid liquid mixed casting technology. In the technology, large amounts of homogeneous alloy powder or heterogenous powder with perfect wettability are added into the superheated melt. After strong agitation, the mixed melt can be cast or hot processed. Applying solid liquid mixed casting, three kinds of Al Si alloys were investigated. The results show that, when the mass of powder accession to alloy melt is about 1, the mean size of primary Si in hyper eutectic alloy can be controlled at less than 5 μm; and the mean grain size of α phase in hypo eutectic alloy is less than 10 μm. This technology has the advantage of preparing material with very fine microstructure by fairly simple casting process, and may be a new practicable and valuable metal preparation technology.
基金This work was supported by the National Natural Science Foundation of China (Grant No. 59734080 and 59504006)the Project of National Fundamental Research and Development of China (Grant No. G1998061510) and High-Tech Research and Development Project
文摘Whether the particle will be trapped by the solid-liquid interface or not is dependent on its moving behavior ahead of the interface, so a mathematical model has been developed to investigate the movement of the particle ahead of the solid-liquid interface. Based on the theory for the boundary layer, the fluid velocity field near the solid-liquid interface was obtained, and the trajectories of particles were calculated by the equations of motion for particles. In this model, the drag force, the added mass force, the buoyance force, the gravitational force, the Saffman force and the Basset history force are considered. The results show that the behavior of the particle ahead of the solid-liquid interface is affected by the physical property of the particle and fluid flow. And in the continuous casting process, if it moves in the stream directed upward or downward near vertical solid-liquid interface or in the horizontal flow under the solid-liquid interface, the particle with the diameter from 5 um to 60um can reach the solid-liquid interface. But if it moves in horizontal flow above the solid-liquid interface, only the particle with the diameter from 5 um to 10 um can reach the solid-liquid interface.
基金Project supported by the Talent Fund of the Ministry of Communication of China(No.95050508) the Fund of Western Communication of China(No.200332822047) the Key Science Fund of the Ministry of Communication of China(No.95060233)
文摘Velocities of solid phase and liquid phase in debris flow are one key problem to research on impact and abrasion mechanism of banks and control structures under action of debris flow. Debris flow was simplified as two-phase liquid composed of solid phase with the same diameter particles and liquid phase with the same mechanical features. Assume debris flow was one-dimension two-phase liquid moving to one direction, then general equations of velocities of solid phase and liquid phase were founded in two-phase theory. Methods to calculate average pressures, volume forces and surface forces of debris flow control volume were established. Specially, surface forces were ascertained using Bingham＇s rheology equation of liquid phase and Bagnold＇s testing results about interaction between particles of solid phase. Proportional coefficient of velocities between liquid phase and solid phase was put forward, meanwhile, divergent coefficient between theoretical velocity and real velocity of solid phase was provided too. To state succinctly before, method to calculate velocities of solid phase and liquid phase was obtained through solution to general equations. The method is suitable for both viscous debris flow and thin debris flow. Additionally, velocities every phase can be identified through analyzing deposits in-situ after occurring of debris flow. It is obvious from engineering case the result in the method is consistent to that in real-time field observation.
基金Project(50972121) supported by the National Nature Science Foundation of ChinaProject(20080004) supported by the Foundation of Key Laboratory for Advanced Materials Processing Technology,Ministry of Education,China
文摘Extended finite element method(XFEM) is proposed to simulate the discontinuous interface in the liquid-solid forming process.The discontinuous interface is an important phenomenon happening in the liquid-solid forming processes and it is difficult to be simulated accurately with conventional finite element method(CFEM) because it involves solid phase and liquid phase simultaneously.XFEM is becoming more and more popular with the need of solving the discontinuous problem happening in engineering field.The implementation method of XFEM is proposed on Abaqus code by using UEL(user element) with the flowchart.The key is to modify the element stiffness in the proposed method by using UEL on the platform of Abaqus code.In contrast to XFEM used in the simulation of solidification,the geometrical and physical properties of elements were modified at the same time in our method that is beneficial to getting smooth interface transition and precise analysis results.The analysis is simplified significantly with XFEM.
基金the financial support by the Austrian Federal Ministry of Economy,Family and Youth and the National Foundation for Research,Technology and Development within the framework of the Christian Doppler Laboratory for Metallurgical Applications of Magnetohydrodynamics.
文摘A funnel-type mold is commonly used to provide necessary clearance for the submerged entry nozzle in the thin slab casting(TSC).The partially solidified shell is subjected to the mechanical deformations,which can lead to the defects formation and,as a results,to a breakout.Traditionally,the results of the flow simulation,performed by the finite volume method(FVM),are fed to the external package for the finite element analysis of stress and strain.A coupled model was assembled using“creeping solid”approach by blending the Norton-Hoff viscoplastic stress for the solidifying shell with the Newtonian viscous stress of the liquid melt.The FVM was used to combine both liquid and solid stress models within a single solver.The iterative procedure based on the improved both side diffusion method was introduced to treat the nonlinear relation between the viscoplastic stress and the strain rate.The modeled shell thickness was verified by previously published breakout measurements and the simulation results.Temperature distribution,obtained during the TSC simulation,dominantly corresponds to the viscoplastic range.Developed numerical approach is robust and has direct industrial application.
基金Funded by the General Program of National Natural Science Foundation of China(Nos.51474189 and 51674222)the Excellent Youth Foundation of Hebei Scientific Committee,China(No.E2018203446)the Scientific Research Foundation of the Higher Education Institutions of Hebei Province,China(No.QN2015214)
文摘To explore the complex thermal-mechanical-chemical behavior in the solid-liquid cast-roll bonding(SLCRB) of Cu/Al cladding strip, numerical simulations were conducted from both macro and micro scales. In macro-scale, with birth and death element method, a thermo-mechanical coupled finite element model(FEM) was set up to explore the temperature and contact pressure distribution at the Cu/Al bonding interface in the SLCRB process. Taking these macro-scale simulation results as boundary conditions, we simulated the atom diffusion law of the bonding interface by molecular dynamics(MD) in micro-scale. The results indicate that the temperature in Cu/Al bonding interface deceases from 700 to 320 ℃ from the entrance to the exit of caster, and the peak of contact pressure reaches up to 140 MPa. The interfacial diffusion thickness depends on temperature and rolling reduction, higher temperature results in larger thickness, and the rolling reduction below kiss point leads to significant elongation deformation of cladding strip which yields more newborn interface with fresh metal and make the diffusion layer thinner. The surface roughness of Cu strip was found to be benefit to atoms diffusion in the Cu/Al bonding interface. Meanwhile, combined with the SEM-EDS observation on the microstructure and composition in the bonding interface of the experimental samples acquired from the castrolling bite, it is revealed that the rolling reduction and severe elongation deformation in the solid-solid contact zone below kiss point guarantee the satisfactory metallurgical bonding with thin and smooth diffusion layer. The bonding mechanisms of reactive diffusion, mechanical interlocking and crack bonding are proved to coexist in the SLCRB process.
基金supported by Department of Energy and Process Engineering,Norwegian University of Science and TechnologyInstitute for Energy Technology and SINTEF through the FACE(Multiphase Flow Assurance Innovation Center) Project
文摘Particle based methods can be used for both the simulations of solid and fluid phases in multiphase medium, such as the discrete-element method for solid phase and the smoothed particle hydrodynamics for fluid phase. This paper presents a computational method combining these two methods for solid-liquid medium. The two phases are coupled by using an improved model from a reported Lagrangian-Eulerian method. The technique is verified by simulating liquid-solid flows in a two-dimensional lid-driven cavity.
基金Item Sponsored by Grant-in-Aid for Young Scientists (B) (No.21760597) from the Japan Society for the Promotion of Science (JSPS)
文摘Rheocasting with semi-solid slurry has been widely used in industrial processes in recent years.The Cup-Cast method is one of the most effective ways to produce semi-solid slurry for rheocasting.In order to study the effect of electromagnetic stirring on the fabrication of semi-solid slurry,we have applied the Double-Axis-Electromagnetic Stirrer(DAEMS)to the Cup-Cast method.Microstructure of the slurry was observed by an optical microscope and Electron Back-Scatter Patterns(EBSP).The results indicated that the electromagnetic stirrer made it possible to accelerate the cooling rate of the melt,thus resulting in a higher quality slurry.
文摘Thin-slab continuous casting and rolling technology is a process integrating casting and plastic deformation. In this study,targeting actions such as slab deformation and liquid core flows during the process of liquid core reduction on thin-slab continuous casting, suggests the fluid-solid coupling method should be used to research the characteristic and patterns of slab deformation during the liquid core reduction process, as well as research liquid core backflows. A material model of the slab shell was obtained through the high-temperature compression test of the cast steel. The analysis of the fluid-solid coupling simulation for liquid core reduction shows that slab deformation concentrates on the narrow side due to the existence of the liquid core. Meanwhile,the stress and strain increases with the increase of the reduction rate and slab thickness. The changing trends of stress and strain are identical under various conditions. The results demonstrate that using greater reduction at the upper part of the slab, which has a higher temperature and thinner slab,is beneficial to the quality of the slab. Moreover,the liquid core is extruded as the reduction is implemented. The quantity of the extrusion increases with the increase of reduction rate and the thickness of thinner shell, which leads to fluctuation of the mould level, making the operation more difficult.
基金Project supported by the National Natural Science Foundation of China (No. 10472036).
文摘This paper employs the integral-averaged method of thickness to approximate the periodical flows in a piezoelectric micropump, with a shallow water equation including nonlinearity and viscous damp presented to characterize the flows in micropump. The finite element method is used to obtain a matrix equation of fluid pressure. The fluid pressure equation is combined with the vibration equation of a silicon diaphragm to construct a liquid-solid coupled equation for reflecting the interaction between solid diaphragm and fluid motion in a micropump. Numerical results of a mode analysis of the coupled system indicate that the natural frequencies of the coupled system are much lower than those of the non-coupled system. The influence of additional mass and viscous damp of fluid on the natural frequencies of the coupled system is more significant as the pump thickness is small. It is found that the vibration shape functions of silicon diaphragm of the coupled system are almost the same as those of the non-coupled system. This paper also gives the first-order amplitude-frequency relationship of the silicon diaphragm, which is necessary for the flow-rate-frequency analysis of a micropump.
基金Item Sponsored by Deutsche Forschungsgemeinschaft (DFG) in frame of the SFB 609"Electromagnetic Flow Control in MetallurgyCrystal Growth and Electrochemistry"
文摘Model experiments with low melting point liquid metals are an important tool to investigate the flow structure and related transport processes in melt flows relevant for metallurgical applications.We present the new experimental facility LIMMCAST for modelling the continuous casting process of steel using the alloy SnBi at temperatures of 200-400℃.The parameters of the facility and the dimensions of the test sections will be given,and the possibilities for flow investigations in tundish,submerged entry nozzle and mould will be discussed.In addition,the smaller set-up Mini-LIMMCAST will be presented,which works with the room-temperature liquid alloy GaInSn.The main value of cold metal laboratory experiments consists in the capabilities to obtain quantitative flow measurements with a reasonable spatial and temporal resolution.New ultrasonic and electromagnetic techniques for measuring the velocity in liquid metal flows came up during the last decade allowing for a satisfying characterisation of flow quantities in the considered temperature range up to 400℃.First results from LIMMCAST and Mini-LIMMCAST will be presented covering the following phenomena:fully contacfless electromagnetic tomography of the flow in the mould,flow monitoring by a multitude of ultrasonic sensors,and analysis of the flow in the mould under the influence of an electromagnetic brake: intensification of the flow turbulence contrary to the expected flow damping,injection of argon bubbles through the stopper rod:occurrence of pressure oscillations.
基金supported by the National Key Technologies Research and Development(R&D)Program by the Ministry of Science and Technology of China(No.2017YFB0406100)the National Natural Science Foundation of China(No.51676123)。
文摘The isothermal single-component multi-phase lattice Boltzmann method(LBM)combined with the particle motion model is used to simulate the detailed process of liquid film rupture induced by a single spherical particle.The entire process of the liquid film rupture can be divided into two stages.In Stage 1,the particle contacts with the liquid film and moves into it due to the interfacial force and finally penetrates the liquid film.Then in Stage 2,the upper and lower liquid surfaces of the thin film are driven by the capillary force and approach to each other along the surface of the particle,resulting in a complete rupture.It is found that a hydrophobic particle with a contact angle of 106.7°shows the shortest rupture duration when the liquid film thickness is less than the particle radius.When the thickness of the liquid film is greater than the immersed depth of the particle at equilibrium,the time of liquid film rupture caused by a hydrophobic particle will be increased.On the other hand,a moderately hydrophilic particle can form a bridge in the middle of the liquid film to enhance the stability of the thin liquid film.
文摘In the paper, 3-D analysis method with unitive schemes is set up, which is used to resolve the uplift with multiple moving boundaries and multiple nonlinear coupling for anchored liquid storage tanks. hi it, an algorithm of quasi-harmonious finite elements for arbitrary quadrilateral of thin plates and shells is built up to analyze the multiple coupling problems of general thin plates and shells structures with three dimensions, the complementary equations for analyzing uplifting moving boundary problems are deduced. The axial symmetry and presumption of beam type mode are not used. In it, an algorithm is put forward for analyzing the Navier-Stokes problems of unsteady, three-dimensional, and viscous liquid with sloshing of moving boundary surfaces in large amplitude under ALE frame by scheme of time-split-steps to which linear potential theory is not applied. The algorithms can be used to analyze the solid-liquid multiple nonlinear coupling problems with 3-D moving boundary with friction in multiple places.
