In this research work,sol-gel technique was employed to prepare the strontium based spinel ferrite nanoparticles(SrFe_(2)O_(4))with different ratios of terbium(Tb).Different characterization techniques were used to in...In this research work,sol-gel technique was employed to prepare the strontium based spinel ferrite nanoparticles(SrFe_(2)O_(4))with different ratios of terbium(Tb).Different characterization techniques were used to investigate the structural,morphological,dielectric and magnetic properties of the prepared samples.X-ray diffraction(XRD)result suggests that face-centered cube spinel nanocrystalline structure is formed.Crystallite size of the SrFe_(2)O_(4)decreases with rising of Tb ratio.The morphology,shape and size of the SrFe_(2)O_(4)were examined by scanning electron microscopy(SEM)analysis and results reveal inhomogeneous distributions of the nanostructures with high agglomeration.The electrical resistivity of the SrFe_(2)O_(4)increases with rising of Tb ratio,which is confirmed from the cyclic voltammetry.It is observed that dielectric constant of all the samples decreases with the increasing frequency range.It is determined that the dielectric constants of the spinel ferrites are frequency dependent and decrease with increasing the frequency of applied electric field.The magnetic behavior of SrFe_(2)O_(4)with different ratios of Tb was studied and it is found that the saturation magnetization values of samples decrease with increase in the substitution of Tb^(3+)at octahedral sites for Fe^(3+).This decrease in the values of M_(s) is also attributed to spin at surface of nanoparticles.展开更多
Ferromagnetic Fe3O4 nanoparticles were synthesized using water as the solvent through the sol-gel method, which was selected for its cost-effectiveness, simplicity, and eco-friendly nature. The synthesized nanoparticl...Ferromagnetic Fe3O4 nanoparticles were synthesized using water as the solvent through the sol-gel method, which was selected for its cost-effectiveness, simplicity, and eco-friendly nature. The synthesized nanoparticles were characterized using a variety of techniques, including Fourier Transform Infrared (FTIR) spectroscopy, X-ray powder diffraction (XRD), Scanning Electron Microscopy (SEM), Thermogravimetric Analysis (TGA), and Vibrating Sample Magnetometer (VSM). These characterizations confirmed the successful formation of Fe3O4 nanoparticles. The FTIR spectra identified characteristic peaks corresponding to the functional groups present, and XRD analysis, using Scherer’s equation, determined an average crystalline size of 1.2 nm for the Fe3O4 nanoparticles. TGA results demonstrated the thermal stability of the nanoparticles, SEM imaging revealed distinct honeycomb-like structures for the nanoparticles synthesized with water as the solvent, while the VSM analysis was used to determine the magnetic behavior of the nanoparticles.展开更多
The precursor sol of alumina was prepared by sol-gel method with aluminum nitrate and malic acid as raw materials.The effects of content of malic acid and polyvinylpyrrolidone （PVP） on sol spinnability were explored...The precursor sol of alumina was prepared by sol-gel method with aluminum nitrate and malic acid as raw materials.The effects of content of malic acid and polyvinylpyrrolidone （PVP） on sol spinnability were explored.The gel fibers with above 80 cm in length were obtained by mixing aluminum nitrate,malic acid and PVP on mass ratio of 10 3 1.5.Thermogravimetry-differential scanning calorimetry （TG-DSC）,Fourier transform infrared （FTIR） spectrum,X-ray diffractometry （XRD）,and scanning electron microscopy （SEM） were used to characterize the properties of the gel and ceramic fibers.The alumina fibers with a smooth surface and about 20μm in diameter were obtained by sintering at 1 200℃,and their main phase was indentified to be α-Al2O3.展开更多
The LiMnPO4/C composite material was synthesized via a sol-gel method based on the citric acid. The X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electrochemical performance tests were adopted to...The LiMnPO4/C composite material was synthesized via a sol-gel method based on the citric acid. The X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electrochemical performance tests were adopted to characterize the properties of LiMnPO4/C. The XRD studies show that the pure olivine phase LiMnPO4 can be obtained at a low temperature of 500 °C. The SEM analyses illustrate that the citric acid used as the chelating reagent and carbon source can restrain the particle size of LiMnPO4/C well. The LiMnPO4/C sample synthesized at 500 °C for 10 h performs the highest initial discharge capacity of 122.6 mA-h/g, retaining 112.4 mA-h/g over 30 cycles at 0.05C rate. The citric acid based sol-gel method is favor to obtain the high electrochemical performance of LiMnPO4/C.展开更多
Porous ZnO films are synthesized by inorganic chelating sol-gel method,which is a novel sol-gel technique using zinc nitrate as starting materials and citric acid as the chelating reagent.The crystal structure,surface...Porous ZnO films are synthesized by inorganic chelating sol-gel method,which is a novel sol-gel technique using zinc nitrate as starting materials and citric acid as the chelating reagent.The crystal structure,surface morphology,porous and optical properties of the deposited films are investigated.X-ray diffraction pattern analysis shows that crystal structure of the ZnO films is hexagonal wurtzite.Scanning electron microscopy (SEM) shows that the ZnO film is porous.The curve of pore size distribution has two peak values at about 2.02nm and 4.97nm and BET surface area of the ZnO film is 27.57m2/g.In addition,the transmittance spectrum gives a high transmittance of 85% in the visible region and optical bandgap of the ZnO film (fired at 500℃) is 3.25eV.展开更多
This work aims to study the solvent’s effect on the structural, morphological, and optical properties of Mg-doped zinc oxide (MZO) thin films. The results of the XRD analysis revealed that the 2-methoxyethanol solven...This work aims to study the solvent’s effect on the structural, morphological, and optical properties of Mg-doped zinc oxide (MZO) thin films. The results of the XRD analysis revealed that the 2-methoxyethanol solvent imparts a preferential orientation to the MZO samples, following the (002) plane, with a maximum value observed at 2% Mg. In contrast, the samples prepared using methanol show no preferential orientation. SEM analysis corroborated that the use of 2-methoxyethanol results in an orderly distribution of MZO crystallites. The optical characterization indicated that the transmittance of MZO thin films reached a maximum value of 90% for Mg concentrations ranging from 2% to 3%. At the same time, the refractive index showed its lowest value of 1.46. In contrast, the use of methanol as a solvent resulted in a maximum transmittance of 80% at 4% Mg, accompanied by a minimum refractive index value of 1.96.展开更多
Nanosized ZnWO4 photocatalysts were successfully synthesized via the sol-gel process in a temperature range of 450-800℃. The grain size, crystal size, and crystallinity of ZnWO4 particles increased with the increase ...Nanosized ZnWO4 photocatalysts were successfully synthesized via the sol-gel process in a temperature range of 450-800℃. The grain size, crystal size, and crystallinity of ZnWO4 particles increased with the increase of calcina- tion temperature and prolonging calcination time. The photocatalytic activity was measured for the degradation of an aqueous Rhodamine-B（RhB） solution and gaseous formaldehyde（FAD）. With the increase of calcination temperature and time, the activities increased to a maximum and then decreased. ZnWO4 photocatalyst prepared at 550℃ for I0 h showed the highest activity, which is similar to the photocatalytic activity of P25TiO2 for the degradation of gase-ous FAD. High crystallinity, large surface area, and good dispersion are responsible for the high photocatalytic per- formance of the prepared ZnWO4.展开更多
The support of catalyst for the direct synthesis of diphenyl carbonate （DPC） by heterogeneous catalytic reaction was prepared by the sol-gel method. Compared with activated charcoal, molecular sieve, porous ceramics...The support of catalyst for the direct synthesis of diphenyl carbonate （DPC） by heterogeneous catalytic reaction was prepared by the sol-gel method. Compared with activated charcoal, molecular sieve, porous ceramics, hopcalite, the support prepared by the sol-gel method has higher activity. The characterization of the support by X-ray diffraction （XRD） and transmission electron microscope （TEM） show that the mare crystal phase is Co2MnO4 and the average particle diameter is about 40 nm. The optimum conditions for synthesis of the support were determined by orthogonal experiments, which indicate that the proportion of Cu, Mn, and Co is the first important factor influencing the yield and selectivity of DPC. Temperature of calcination is the second one. The optimum conditions are： molar proportion of Cu, Mn, and Co being 1 ： 1 ： 1, temperature of calcination 700℃, drying at 100~C, temperature of water bath 85~C. The yield and selectivity of DPC in the process can reach 38% and 99% in the batch operation, respectively. The copper cobalt manganese mixed oxides chosen as the support contribute more to the high catalytic activity than the sol-gel method.展开更多
Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were...Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were characterized by scanning electron microscopy (SEM) , X-ray diffraction (XRD), transmission electron microscopy ( TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometer ( UV-VIS). The photocatalytic activity of TiO2 thin films was evaluated for the photocatalytic decolorization of aqueous methyl orange . The effects of film thickness on the crystalline phase, grain size, transmittance and photocatalytic activity of nanometer Ti02 thin films were discussed.展开更多
A sodium sulfate （NaeSO4）/silica （SiO2） composite was prepared as a shape-stabilized solid-liquid phase change material by a sol-gel procedure using Na2SiO3 as the silica source. Na2SO4 in the composite acts as a ...A sodium sulfate （NaeSO4）/silica （SiO2） composite was prepared as a shape-stabilized solid-liquid phase change material by a sol-gel procedure using Na2SiO3 as the silica source. Na2SO4 in the composite acts as a latent heat storage substance for solid-liquid phase change, while SiO2 acts as a support material to provide structural strength and prevent leakage of melted NazSO4. The microstructure and composition of the prepared composite were characterized by the N2 adsorption, transmission electron microscope （TEM）, scanning electron microscope （SEM）, Fourier transform infrared spectroscopy （FTIR） and X-ray diffraction. The results show that the prepared Na2SOJSiO2 composite is a nanostructured hybrid of NazSO4 and SiO2 without new substances produced during the phase change. The macroscopic shape of the NazSO4/SiO2 composite after the melting and freezing cycles does not change and there is no leakage of Na2SO4. Determined by differential scanning calorimeter （DSC） analysis, the values of phase change latent heat of melting and freezing of the prepared NazSO4/SiO2 （50%, by mass） composite are 82.3 kJ.kg i and 83.7 kJ.kg-1, and temperatures of melting and freezing are 886.0 ℃ and 880.6 ℃, respectively. Furthermore, the Na2SOJSiO2 composite maintains good thermal energy storage and release ability even after 100 cycles of melting and freezing. The satisfactory thermal storage performance renders this composite a versatile tool for high-temperature thermal energy storage.展开更多
The Bi3＋ doped molybdate-based red-emitting phosphors, LiEu1-xBix（MoO4）2, were successfully synthesized with a sol-gel method. The prepared LiEu1-xBix（MoO4）2 phosphors exhibited pure and intense red emission at 6...The Bi3＋ doped molybdate-based red-emitting phosphors, LiEu1-xBix（MoO4）2, were successfully synthesized with a sol-gel method. The prepared LiEu1-xBix（MoO4）2 phosphors exhibited pure and intense red emission at 613 nm under the excitation of near-UV 394 nm. It was discussed in detail that the influence of the synthesis conditions such as the doping concentration of Bi3, the dose of citric acid, pH of the precursor solution and the sintering temperature on the emission intensity of the phosphors. According to the results, the optimal condition was obtained： the doping concentration of Bi3＋ was 15 mol.%, molar ratio of citric acid to metal ions was 1.5：1, pH of the precursor solution was 1.0 and the sintering temperature was 800 ℃. The X-ray diffraction （XRD） patterns of the LiEuo.85Bi0.15（MoO4）2 phosphor prepared under the optimal condition indicated that the phosphor was single phase with tetragonal scheelite structure. The Commission Intemationale de I＇E- clairage （CIE） chromaticity coordinates of LiEuo.85Bio.15（MoO4）2 were （x=0.655, y=0.345）, which were closer to the national television stan- dard committee （NTSC） standard values （x=0.670, y=0.330） than that of a commercial red phosphor of Y202S：Eu3＋（x=0.630, y=0.350）. This LiEuo.85Bi0As（MoO4）2 red phosphor is a promising candidate for the fabrication of white light-emitting diode （W-LED） with near-UV chips.展开更多
The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an incr...The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an increase of surface area from 66.8 to 80.4 m^2· g^-1 compared with the undoped sample Ce0 .6oZr0.40O2 65.1 m^2·g^- 1 after calcination at 650℃. Transmission electron microscopy （TEM） observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce^4＋ and Tb^3 ＋ , and Zr existed in the form of Zr^4＋ on the surface of the samples. The doped samples were homogenous in composition ; the introduction of Tb into the CeO2-ZrO2 promoters resuited in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.展开更多
Long afterglow photoluminescent materials Sr2MgSi2O7 doped with Eu2+, Dy3+ were prepared by sol-gel method. The synthesized samples were characterized by X-ray diffraction. The excitation spectrum, emission spectrum a...Long afterglow photoluminescent materials Sr2MgSi2O7 doped with Eu2+, Dy3+ were prepared by sol-gel method. The synthesized samples were characterized by X-ray diffraction. The excitation spectrum, emission spectrum and long decay curve were measured and analyzed. XRD pattern indicates that phosphor is with Sr2MgSi2O7 crystal structure. The wide range of excitation wavelength indicates that luminescent material can be excited by light from ultraviolet ray to visible light. The main peak of emission spectrum is located at 466 nm. Sample excited by visible light can emit bright blue light, and the afterglow time lasts more than 8 h.展开更多
TeOx-SiO2 composite films having third-order nonlinearities were prepared by electrochemically induced sol-gel deposition method on ITO substrate.The third-order optical nonlinearities of the films were measured by Z-...TeOx-SiO2 composite films having third-order nonlinearities were prepared by electrochemically induced sol-gel deposition method on ITO substrate.The third-order optical nonlinearities of the films were measured by Z-scan technique.The third-order nonlinear susceptibilities（χ^（（3））） of the as-prepared films are 5.9×10^（-7） to 4.29×10^（-6）esu.The surface morphology and composition of the films were characterized by SEM/EDX,which identified that Te metallic particles well dispersed in TeO_x-SiO_2 gel films.展开更多
A series of red-emitting Ca2_xA12SiOT：xEu^3＋ （x = 1 mol.%-10 tool.%） phosphors were synthesized by the sol-gel method. The effects of annealing temperature and doping concentration on the crystal structure and lum...A series of red-emitting Ca2_xA12SiOT：xEu^3＋ （x = 1 mol.%-10 tool.%） phosphors were synthesized by the sol-gel method. The effects of annealing temperature and doping concentration on the crystal structure and luminescence properties of Ca2A12SiO7：Eu^3＋ phosphors were investigated. X-ray diffraction （XRD） profiles showed that all peaks could be attributed to the tetragonal Ca2A12SiO7 phase when the sample was annealed at 1000℃. Scanning electron microscopy （SEM） micrographs indicate that the phosphors have an irregularly rounded mor- phology with particles of about 200 nm. Excitation spectra showed that the strong broad band at around 258 nm and weak sharp lines in 350-490 nm were attributed to the charge transfer band of Eu^3＋-O^2- and f-f transitions within the 4f^6 configuration of Eu^3＋ ions, respectively. Emission spectra implied that the red luminescence could be attributed to the transitions from the ^5D0 excited level to the 7Fj （J = 0, 1, 2, 3, 4） levels of Eu3＋ions with the main electric dipole transition ^5D0→^7F2 （618 and 620 nm）, and Eu^3＋ ions prefer to occupy a lower symmetry site in the crystal lattice. Moreover, the photoluminescence （PL） intensity was strongly dependent on both the sintering temperature and doping concentration, and the highest PL intensity was observed at an Eu^3＋ concentration x = 7 mol.% after annealing at ll00℃. The obtained Ca2A12SiO7：Eu^＋3＋ phosphor may have potential application for the red lamp phosphor.展开更多
The nickel-based catalysts were prepared by the sol-gel method and used for the CH4 reforming with CO2. The effects of the sol-gel method on the specific surface area, catalytic activity, desorption, and reduction per...The nickel-based catalysts were prepared by the sol-gel method and used for the CH4 reforming with CO2. The effects of the sol-gel method on the specific surface area, catalytic activity, desorption, and reduction performances of catalysts were investigated with BET, TPR, and TPD. Compared with the catalyst prepared by the impregnation method, the results indicated that the catalysts prepared by the sol-gel method had larger specific surface area, showing higher catalytic activities and exhibiting perfect desorption and reduction performances. In addition, the modification effects of adding La were studied, and it was found that the 0.75NLBT catalyst constituted of 5wt.%Ni-0.75wt.%La was optimal.展开更多
Eu 2+, Dy 3+ co-doped nanocrystalline strontium aluminate phosphor powders with brightness and long afterglow were synthesized by the sol-gel method at 1200 ℃ for 2 h. The samples were characterized by X-ray diffract...Eu 2+, Dy 3+ co-doped nanocrystalline strontium aluminate phosphor powders with brightness and long afterglow were synthesized by the sol-gel method at 1200 ℃ for 2 h. The samples were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results of XRD show that the single crystalline phase is α-SrAl_2O_4. According to the observation of SEM, the particles of the samples are needle-like. Compared with the samples synthesized by solid state reaction, the grain size of the sol-gel method is to nanometer grade. A clear blue shift occurs in the excitation and emission spectra. The blue shift in nanocrystalline SrAl_2O_4∶Eu, Dy phosphor can be attributed to the quantum-size-effect of the luminescent particles.展开更多
SiO2-CaO-MgO glass and glass-ceramic powder doped with Nd3＋ were synthesized with sol-gel method. Tetraethylorthosilicate （TEOS）, Ca（NO3）2？4H2O, Mg（NO3）2？6H2O, Nd（NO3）3？6H2O, ethanol, distilled water, and ...SiO2-CaO-MgO glass and glass-ceramic powder doped with Nd3＋ were synthesized with sol-gel method. Tetraethylorthosilicate （TEOS）, Ca（NO3）2？4H2O, Mg（NO3）2？6H2O, Nd（NO3）3？6H2O, ethanol, distilled water, and HNO3 were used as starting materials. The synthesized powder’s properties were examined with simultaneous thermal analysis （STA）, X-ray diffraction （XRD）, photoluminescence （PL） and scanning electron microscopy （SEM） analysis. The STA curves showed that the softening point and crystallization temperatures were shifted to higher temperatures with increasing dopant content. Regarding XRD patterns of glass samples, Nd was found to act as an intermediate oxide in glass matrix. The XRD patterns of glass-ceramic samples indicated that bredigite and akermanite crystallized in the glass matrix after heat treating at 900 oC. The fluorescence spectra showed that glass-ceramics emitted much stronger irradiation than glasses with the same dopant content. The SEM images illustrated uniform and homogeneous distribution of applied oxides in glass and glass-ceramic compositions.展开更多
Undoped and Na-doped ZnO films were deposited by sol-gel method.The effects of sodium incorporation on structure,surface morphology and optical constants of the films were investigated.X-ray diffraction patterns show ...Undoped and Na-doped ZnO films were deposited by sol-gel method.The effects of sodium incorporation on structure,surface morphology and optical constants of the films were investigated.X-ray diffraction patterns show the hexagonal wurtzite polycrystalline structure and that the sodium incorporation leads to the change in the structural characteristics of ZnO films.The SEM observations show that the surface morphology of the films is affected by the sodium incorporation.The transmission spectra show that the average transmittance of the films is above 85% in the visible range.The absorption edge initially blue-shifts and then red-shifts with the increase of Na doping content.The optical constants of these films were calculated using transmission spectra.Refractive indices of the films in the visible range decrease at first and then increase with increasing Na doping content.展开更多
Two series of perovskite-type oxides with composition (La_(1-x))Sr_xFeO_3(x≤0.8)and La_(1-x)Sr_xFe_(1-y)Co_yO_3(x=0.2; y=0.2, 0.4)powder productions were synthesized by EDTA complexing sol-gel method. The products we...Two series of perovskite-type oxides with composition (La_(1-x))Sr_xFeO_3(x≤0.8)and La_(1-x)Sr_xFe_(1-y)Co_yO_3(x=0.2; y=0.2, 0.4)powder productions were synthesized by EDTA complexing sol-gel method. The products were characterized by XRD, TEM, SEM, BET method(N_2 adsorption)and laser granularity analysis for different synthesis conditions to obtain the optimum conditions for the preparation process. Single-phased, uniform perovskite-type oxides with small particle size were obtained by EDTA sol-gel process with high stability and repeatability, and the process temperature is much lower than that of solid state reaction method.展开更多
基金the Deanship of Scientific Research at King Khalid University for funding this work through Large Groups Project under(RGP.2/111/44)。
文摘In this research work,sol-gel technique was employed to prepare the strontium based spinel ferrite nanoparticles(SrFe_(2)O_(4))with different ratios of terbium(Tb).Different characterization techniques were used to investigate the structural,morphological,dielectric and magnetic properties of the prepared samples.X-ray diffraction(XRD)result suggests that face-centered cube spinel nanocrystalline structure is formed.Crystallite size of the SrFe_(2)O_(4)decreases with rising of Tb ratio.The morphology,shape and size of the SrFe_(2)O_(4)were examined by scanning electron microscopy(SEM)analysis and results reveal inhomogeneous distributions of the nanostructures with high agglomeration.The electrical resistivity of the SrFe_(2)O_(4)increases with rising of Tb ratio,which is confirmed from the cyclic voltammetry.It is observed that dielectric constant of all the samples decreases with the increasing frequency range.It is determined that the dielectric constants of the spinel ferrites are frequency dependent and decrease with increasing the frequency of applied electric field.The magnetic behavior of SrFe_(2)O_(4)with different ratios of Tb was studied and it is found that the saturation magnetization values of samples decrease with increase in the substitution of Tb^(3+)at octahedral sites for Fe^(3+).This decrease in the values of M_(s) is also attributed to spin at surface of nanoparticles.
文摘Ferromagnetic Fe3O4 nanoparticles were synthesized using water as the solvent through the sol-gel method, which was selected for its cost-effectiveness, simplicity, and eco-friendly nature. The synthesized nanoparticles were characterized using a variety of techniques, including Fourier Transform Infrared (FTIR) spectroscopy, X-ray powder diffraction (XRD), Scanning Electron Microscopy (SEM), Thermogravimetric Analysis (TGA), and Vibrating Sample Magnetometer (VSM). These characterizations confirmed the successful formation of Fe3O4 nanoparticles. The FTIR spectra identified characteristic peaks corresponding to the functional groups present, and XRD analysis, using Scherer’s equation, determined an average crystalline size of 1.2 nm for the Fe3O4 nanoparticles. TGA results demonstrated the thermal stability of the nanoparticles, SEM imaging revealed distinct honeycomb-like structures for the nanoparticles synthesized with water as the solvent, while the VSM analysis was used to determine the magnetic behavior of the nanoparticles.
基金Project(2010K10-21) supported by the Natural Science Foundation of Shaanxi Province,China
文摘The precursor sol of alumina was prepared by sol-gel method with aluminum nitrate and malic acid as raw materials.The effects of content of malic acid and polyvinylpyrrolidone （PVP） on sol spinnability were explored.The gel fibers with above 80 cm in length were obtained by mixing aluminum nitrate,malic acid and PVP on mass ratio of 10 3 1.5.Thermogravimetry-differential scanning calorimetry （TG-DSC）,Fourier transform infrared （FTIR） spectrum,X-ray diffractometry （XRD）,and scanning electron microscopy （SEM） were used to characterize the properties of the gel and ceramic fibers.The alumina fibers with a smooth surface and about 20μm in diameter were obtained by sintering at 1 200℃,and their main phase was indentified to be α-Al2O3.
基金Project (0991025) supported by Natural Science Foundation of Guangxi, ChinaProject (51164007) supported by the National Natural Science Foundation of ChinaProject (201101ZD008) supported by Educational Commission of Guangxi, China
文摘The LiMnPO4/C composite material was synthesized via a sol-gel method based on the citric acid. The X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electrochemical performance tests were adopted to characterize the properties of LiMnPO4/C. The XRD studies show that the pure olivine phase LiMnPO4 can be obtained at a low temperature of 500 °C. The SEM analyses illustrate that the citric acid used as the chelating reagent and carbon source can restrain the particle size of LiMnPO4/C well. The LiMnPO4/C sample synthesized at 500 °C for 10 h performs the highest initial discharge capacity of 122.6 mA-h/g, retaining 112.4 mA-h/g over 30 cycles at 0.05C rate. The citric acid based sol-gel method is favor to obtain the high electrochemical performance of LiMnPO4/C.
文摘Porous ZnO films are synthesized by inorganic chelating sol-gel method,which is a novel sol-gel technique using zinc nitrate as starting materials and citric acid as the chelating reagent.The crystal structure,surface morphology,porous and optical properties of the deposited films are investigated.X-ray diffraction pattern analysis shows that crystal structure of the ZnO films is hexagonal wurtzite.Scanning electron microscopy (SEM) shows that the ZnO film is porous.The curve of pore size distribution has two peak values at about 2.02nm and 4.97nm and BET surface area of the ZnO film is 27.57m2/g.In addition,the transmittance spectrum gives a high transmittance of 85% in the visible region and optical bandgap of the ZnO film (fired at 500℃) is 3.25eV.
文摘This work aims to study the solvent’s effect on the structural, morphological, and optical properties of Mg-doped zinc oxide (MZO) thin films. The results of the XRD analysis revealed that the 2-methoxyethanol solvent imparts a preferential orientation to the MZO samples, following the (002) plane, with a maximum value observed at 2% Mg. In contrast, the samples prepared using methanol show no preferential orientation. SEM analysis corroborated that the use of 2-methoxyethanol results in an orderly distribution of MZO crystallites. The optical characterization indicated that the transmittance of MZO thin films reached a maximum value of 90% for Mg concentrations ranging from 2% to 3%. At the same time, the refractive index showed its lowest value of 1.46. In contrast, the use of methanol as a solvent resulted in a maximum transmittance of 80% at 4% Mg, accompanied by a minimum refractive index value of 1.96.
基金Supported by the National Natural Science Foundation of China(Nos.20433010and20571047)Specialized Research Fundfor the Doctoral Program of Higher Education(No.20060003082).
文摘Nanosized ZnWO4 photocatalysts were successfully synthesized via the sol-gel process in a temperature range of 450-800℃. The grain size, crystal size, and crystallinity of ZnWO4 particles increased with the increase of calcina- tion temperature and prolonging calcination time. The photocatalytic activity was measured for the degradation of an aqueous Rhodamine-B（RhB） solution and gaseous formaldehyde（FAD）. With the increase of calcination temperature and time, the activities increased to a maximum and then decreased. ZnWO4 photocatalyst prepared at 550℃ for I0 h showed the highest activity, which is similar to the photocatalytic activity of P25TiO2 for the degradation of gase-ous FAD. High crystallinity, large surface area, and good dispersion are responsible for the high photocatalytic per- formance of the prepared ZnWO4.
文摘The support of catalyst for the direct synthesis of diphenyl carbonate （DPC） by heterogeneous catalytic reaction was prepared by the sol-gel method. Compared with activated charcoal, molecular sieve, porous ceramics, hopcalite, the support prepared by the sol-gel method has higher activity. The characterization of the support by X-ray diffraction （XRD） and transmission electron microscope （TEM） show that the mare crystal phase is Co2MnO4 and the average particle diameter is about 40 nm. The optimum conditions for synthesis of the support were determined by orthogonal experiments, which indicate that the proportion of Cu, Mn, and Co is the first important factor influencing the yield and selectivity of DPC. Temperature of calcination is the second one. The optimum conditions are： molar proportion of Cu, Mn, and Co being 1 ： 1 ： 1, temperature of calcination 700℃, drying at 100~C, temperature of water bath 85~C. The yield and selectivity of DPC in the process can reach 38% and 99% in the batch operation, respectively. The copper cobalt manganese mixed oxides chosen as the support contribute more to the high catalytic activity than the sol-gel method.
基金This work was financially supported by Foundation for Uni-versity Key Teacher by the Ministry of Education, the National Natu-ral Science Foundation of China (No. 50072016) and the Key Re-search Project of the Ministry of Education(No.99087)
文摘Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were characterized by scanning electron microscopy (SEM) , X-ray diffraction (XRD), transmission electron microscopy ( TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometer ( UV-VIS). The photocatalytic activity of TiO2 thin films was evaluated for the photocatalytic decolorization of aqueous methyl orange . The effects of film thickness on the crystalline phase, grain size, transmittance and photocatalytic activity of nanometer Ti02 thin films were discussed.
基金Supported by the National Natural Science Foundation of China(2107611)
文摘A sodium sulfate （NaeSO4）/silica （SiO2） composite was prepared as a shape-stabilized solid-liquid phase change material by a sol-gel procedure using Na2SiO3 as the silica source. Na2SO4 in the composite acts as a latent heat storage substance for solid-liquid phase change, while SiO2 acts as a support material to provide structural strength and prevent leakage of melted NazSO4. The microstructure and composition of the prepared composite were characterized by the N2 adsorption, transmission electron microscope （TEM）, scanning electron microscope （SEM）, Fourier transform infrared spectroscopy （FTIR） and X-ray diffraction. The results show that the prepared Na2SOJSiO2 composite is a nanostructured hybrid of NazSO4 and SiO2 without new substances produced during the phase change. The macroscopic shape of the NazSO4/SiO2 composite after the melting and freezing cycles does not change and there is no leakage of Na2SO4. Determined by differential scanning calorimeter （DSC） analysis, the values of phase change latent heat of melting and freezing of the prepared NazSO4/SiO2 （50%, by mass） composite are 82.3 kJ.kg i and 83.7 kJ.kg-1, and temperatures of melting and freezing are 886.0 ℃ and 880.6 ℃, respectively. Furthermore, the Na2SOJSiO2 composite maintains good thermal energy storage and release ability even after 100 cycles of melting and freezing. The satisfactory thermal storage performance renders this composite a versatile tool for high-temperature thermal energy storage.
基金Project supported by National Natural Science Foundation of China (NSFC20803097, NSFC20603049)Natural Science Foundation of Chongqing (CSTC2011AB4056, CSTC2009BA4023)the Fundamental Research Funds for the Central Universities (CDJZR10220005 and CDJRC10220002)
文摘The Bi3＋ doped molybdate-based red-emitting phosphors, LiEu1-xBix（MoO4）2, were successfully synthesized with a sol-gel method. The prepared LiEu1-xBix（MoO4）2 phosphors exhibited pure and intense red emission at 613 nm under the excitation of near-UV 394 nm. It was discussed in detail that the influence of the synthesis conditions such as the doping concentration of Bi3, the dose of citric acid, pH of the precursor solution and the sintering temperature on the emission intensity of the phosphors. According to the results, the optimal condition was obtained： the doping concentration of Bi3＋ was 15 mol.%, molar ratio of citric acid to metal ions was 1.5：1, pH of the precursor solution was 1.0 and the sintering temperature was 800 ℃. The X-ray diffraction （XRD） patterns of the LiEuo.85Bi0.15（MoO4）2 phosphor prepared under the optimal condition indicated that the phosphor was single phase with tetragonal scheelite structure. The Commission Intemationale de I＇E- clairage （CIE） chromaticity coordinates of LiEuo.85Bio.15（MoO4）2 were （x=0.655, y=0.345）, which were closer to the national television stan- dard committee （NTSC） standard values （x=0.670, y=0.330） than that of a commercial red phosphor of Y202S：Eu3＋（x=0.630, y=0.350）. This LiEuo.85Bi0As（MoO4）2 red phosphor is a promising candidate for the fabrication of white light-emitting diode （W-LED） with near-UV chips.
基金Project supported by the Natural Science Basic Research Plan in Shaanxi Province of China (2004B13)
文摘The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an increase of surface area from 66.8 to 80.4 m^2· g^-1 compared with the undoped sample Ce0 .6oZr0.40O2 65.1 m^2·g^- 1 after calcination at 650℃. Transmission electron microscopy （TEM） observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce^4＋ and Tb^3 ＋ , and Zr existed in the form of Zr^4＋ on the surface of the samples. The doped samples were homogenous in composition ; the introduction of Tb into the CeO2-ZrO2 promoters resuited in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.
文摘Long afterglow photoluminescent materials Sr2MgSi2O7 doped with Eu2+, Dy3+ were prepared by sol-gel method. The synthesized samples were characterized by X-ray diffraction. The excitation spectrum, emission spectrum and long decay curve were measured and analyzed. XRD pattern indicates that phosphor is with Sr2MgSi2O7 crystal structure. The wide range of excitation wavelength indicates that luminescent material can be excited by light from ultraviolet ray to visible light. The main peak of emission spectrum is located at 466 nm. Sample excited by visible light can emit bright blue light, and the afterglow time lasts more than 8 h.
基金supported by Academic Program of Natural Science Foundation Project of CQ CSTC(No 2008BC4003)the Foundation of State Key Laboratory of Physical Chemistry of Solid Surfaces of Xiamen University(No2007)
文摘TeOx-SiO2 composite films having third-order nonlinearities were prepared by electrochemically induced sol-gel deposition method on ITO substrate.The third-order optical nonlinearities of the films were measured by Z-scan technique.The third-order nonlinear susceptibilities（χ^（（3））） of the as-prepared films are 5.9×10^（-7） to 4.29×10^（-6）esu.The surface morphology and composition of the films were characterized by SEM/EDX,which identified that Te metallic particles well dispersed in TeO_x-SiO_2 gel films.
基金supported by the National Natural Science Foundation of China (No. 10874160)the Science and Technology Foundation of Guangdong Province,China (No. 2007173)the Science and Technology Foundation of Jiangmen City, China (No. 2007028)
文摘A series of red-emitting Ca2_xA12SiOT：xEu^3＋ （x = 1 mol.%-10 tool.%） phosphors were synthesized by the sol-gel method. The effects of annealing temperature and doping concentration on the crystal structure and luminescence properties of Ca2A12SiO7：Eu^3＋ phosphors were investigated. X-ray diffraction （XRD） profiles showed that all peaks could be attributed to the tetragonal Ca2A12SiO7 phase when the sample was annealed at 1000℃. Scanning electron microscopy （SEM） micrographs indicate that the phosphors have an irregularly rounded mor- phology with particles of about 200 nm. Excitation spectra showed that the strong broad band at around 258 nm and weak sharp lines in 350-490 nm were attributed to the charge transfer band of Eu^3＋-O^2- and f-f transitions within the 4f^6 configuration of Eu^3＋ ions, respectively. Emission spectra implied that the red luminescence could be attributed to the transitions from the ^5D0 excited level to the 7Fj （J = 0, 1, 2, 3, 4） levels of Eu3＋ions with the main electric dipole transition ^5D0→^7F2 （618 and 620 nm）, and Eu^3＋ ions prefer to occupy a lower symmetry site in the crystal lattice. Moreover, the photoluminescence （PL） intensity was strongly dependent on both the sintering temperature and doping concentration, and the highest PL intensity was observed at an Eu^3＋ concentration x = 7 mol.% after annealing at ll00℃. The obtained Ca2A12SiO7：Eu^＋3＋ phosphor may have potential application for the red lamp phosphor.
基金supported by the Jiangxi Provincial Department of Education
文摘The nickel-based catalysts were prepared by the sol-gel method and used for the CH4 reforming with CO2. The effects of the sol-gel method on the specific surface area, catalytic activity, desorption, and reduction performances of catalysts were investigated with BET, TPR, and TPD. Compared with the catalyst prepared by the impregnation method, the results indicated that the catalysts prepared by the sol-gel method had larger specific surface area, showing higher catalytic activities and exhibiting perfect desorption and reduction performances. In addition, the modification effects of adding La were studied, and it was found that the 0.75NLBT catalyst constituted of 5wt.%Ni-0.75wt.%La was optimal.
文摘Eu 2+, Dy 3+ co-doped nanocrystalline strontium aluminate phosphor powders with brightness and long afterglow were synthesized by the sol-gel method at 1200 ℃ for 2 h. The samples were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results of XRD show that the single crystalline phase is α-SrAl_2O_4. According to the observation of SEM, the particles of the samples are needle-like. Compared with the samples synthesized by solid state reaction, the grain size of the sol-gel method is to nanometer grade. A clear blue shift occurs in the excitation and emission spectra. The blue shift in nanocrystalline SrAl_2O_4∶Eu, Dy phosphor can be attributed to the quantum-size-effect of the luminescent particles.
基金supported by the Iran Nanotechnology Initiative Council(INIC)
文摘SiO2-CaO-MgO glass and glass-ceramic powder doped with Nd3＋ were synthesized with sol-gel method. Tetraethylorthosilicate （TEOS）, Ca（NO3）2？4H2O, Mg（NO3）2？6H2O, Nd（NO3）3？6H2O, ethanol, distilled water, and HNO3 were used as starting materials. The synthesized powder’s properties were examined with simultaneous thermal analysis （STA）, X-ray diffraction （XRD）, photoluminescence （PL） and scanning electron microscopy （SEM） analysis. The STA curves showed that the softening point and crystallization temperatures were shifted to higher temperatures with increasing dopant content. Regarding XRD patterns of glass samples, Nd was found to act as an intermediate oxide in glass matrix. The XRD patterns of glass-ceramic samples indicated that bredigite and akermanite crystallized in the glass matrix after heat treating at 900 oC. The fluorescence spectra showed that glass-ceramics emitted much stronger irradiation than glasses with the same dopant content. The SEM images illustrated uniform and homogeneous distribution of applied oxides in glass and glass-ceramic compositions.
基金Project(50872001) supported by the National Natural Science Foundation of ChinaProject(20060357003) supported by Research Fund for the Doctoral Program of Higher Education of ChinaProject(KJ2010A284) supported by the Natural Science Foundation of Anhui Higher Education Institution of China
文摘Undoped and Na-doped ZnO films were deposited by sol-gel method.The effects of sodium incorporation on structure,surface morphology and optical constants of the films were investigated.X-ray diffraction patterns show the hexagonal wurtzite polycrystalline structure and that the sodium incorporation leads to the change in the structural characteristics of ZnO films.The SEM observations show that the surface morphology of the films is affected by the sodium incorporation.The transmission spectra show that the average transmittance of the films is above 85% in the visible range.The absorption edge initially blue-shifts and then red-shifts with the increase of Na doping content.The optical constants of these films were calculated using transmission spectra.Refractive indices of the films in the visible range decrease at first and then increase with increasing Na doping content.
文摘Two series of perovskite-type oxides with composition (La_(1-x))Sr_xFeO_3(x≤0.8)and La_(1-x)Sr_xFe_(1-y)Co_yO_3(x=0.2; y=0.2, 0.4)powder productions were synthesized by EDTA complexing sol-gel method. The products were characterized by XRD, TEM, SEM, BET method(N_2 adsorption)and laser granularity analysis for different synthesis conditions to obtain the optimum conditions for the preparation process. Single-phased, uniform perovskite-type oxides with small particle size were obtained by EDTA sol-gel process with high stability and repeatability, and the process temperature is much lower than that of solid state reaction method.
