With the generation of both localised thermal and vibration in incremental sheet forming(ISF)by novel tool designs,rotational vibration assisted ISF(RV-ISF)can achieve significant force reduction and material softenin...With the generation of both localised thermal and vibration in incremental sheet forming(ISF)by novel tool designs,rotational vibration assisted ISF(RV-ISF)can achieve significant force reduction and material softening.However,the combined thermal and vibration softening in RV-ISF is unclear.By evaluating the similarities and differences of friction stir ISF(FS-ISF)and RV-ISF,this study develops a novel approach to decouple and quantify the thermal and vibration softening effects in RV-ISF of AZ31B-H24,providing new insights into underlying thermal and vibration softening mechanism.Experimental results reveal that in RV-ISF of AZ31B-H24 the thermal softening due to frictional heating dominates with 45∼65%of softening,while the vibration effect only contributes up to 15%of softening,from the conventional ISF,depending on the tool designs and tool rotational speed.The double-offset tool(T2)produces greater vibration softening than the three-groove tool(T3)owing to the higher vibration amplitude of the T2 tool.An increase in tool rotational speed primarily enhances thermal softening with only marginal changes to the vibration effect.Microstructural analysis suggests that with average grain size of 0.94μm at the top layer,RV-ISF with T3 and 3000 rpm is more effective for microstructure refinement than that by FS-ISF,especially on the tool-sheet contact surface,which confirms the occurrence of surface shearing.This refinement is a result of the reduced recrystallisation degree,71.8%at the top bottom layer.Compared with FS-ISF,RV-ISF can lead to not only higher geometrically necessary dislocation density,but also higher fraction of low-angle grain boundaries,indicating that softening mechanism due to localised vibration effect is resulted from the enhanced rearrangement and annihilation of dislocations.These findings contribute to new understanding of the thermal and vibration softening effects in RV-ISF of AZ31B-H24 and offer a theoretical foundation for the tool design and process optimisation.展开更多
In this paper,the work hardening and softening behavior of AZ31 magnesium alloy sheets by hard plate accumulative roll bonding(HP-ARB)process in a specific temperature range was studied for the first time,and the cycl...In this paper,the work hardening and softening behavior of AZ31 magnesium alloy sheets by hard plate accumulative roll bonding(HP-ARB)process in a specific temperature range was studied for the first time,and the cyclic stress relaxation test,EBSD,TEM and other characterization methods were used.When the rolling temperature is 350℃,the grain size of magnesium sheets is refined to 4.32(±0.36)μm on average,and it shows an excellent combination of strength and plasticity.The tensile strength reaches 307(±8.52)MPa and the elongation is 12.73(±0.84)%.At this time,the curve of work hardening rate decreases smoothly and the degree of hardening is the lowest,and the amplitude of stress drop △σ_(p) in work softening test is the smallest with the increase of cycle times,which shows that the well coordination between work hardening and softening behavior has been achieved.Research has found that the combined effect of grain boundary strengthening and fine grain strengthening enhances the yield and tensile strength of magnesium sheets after three passes HP-ARB process at 350℃.This is attributed to the high degree of dislocation slip opening in the pyramidal surfaceand<c+a>,which not only coordinates the c-axis strain of the entire grain,but also promotes the slip transfer of dislocations in the fine-grained region,significantly improving the elongation of the sheets.This study provides a new idea for the forming and manufacturing of high performance magnesium alloy sheets.展开更多
To obtain the Ti_(p)with different aspect ratios,the Ti_(p)/Mg-5Zn-0.3Ca composite prepared by semi-solid stir casting was subjected to extrusion at 220℃,180℃,and 140℃,respectively.Then,the effect of the Ti_(p)’s ...To obtain the Ti_(p)with different aspect ratios,the Ti_(p)/Mg-5Zn-0.3Ca composite prepared by semi-solid stir casting was subjected to extrusion at 220℃,180℃,and 140℃,respectively.Then,the effect of the Ti_(p)’s aspect ratio on the microstructure,mechanical properties,work hardening and softening behaviors of Ti_(p)/Mg-5Zn-0.3Ca composites was investigated.The results indicated that the Ti_(p)could be elongated obviously after low-temperature extrusion,and the aspect ratio of which would reach to 13.7:1 as the extrusion temperature deceased to 140℃.Then the“Ti/Mg”layer-like structure was formed in the Ti_(p)/Mg-5Zn-0.3Ca composite.Accompanied with the elongation of Ti_(p),the dynamic recrystallized grains and dynamic precipitates were both refined significantly,however,the dynamic recrystallization rate changed a little.The elongated Ti_(p)endowed the Ti_(p)/Mg-5Zn-0.3Ca composites with better matching of strength and toughness without the sacrifice of elongation and bending strain.Both the work hardening rate and softening rate of Ti_(p)/Mg-5Zn-0.3Ca composites increased with the increasing aspect ratio of Ti_(p).The formation of“Ti/Mg”layer-like structure contributed to the redistribution of strain from large aggregations to a network-like distribution,which effectively suppresses the initiation and propagation of micro-cracks,thus enhancing the plasticity of the Ti_(p)/Mg-5Zn-0.3Ca composites.展开更多
In order to obtain a lower frequency band gap,this paper proposes a novel locally resonant meta-beam incorporating a softening nonlinear factor.An improved camroller structure is designed in this meta-beam to achieve ...In order to obtain a lower frequency band gap,this paper proposes a novel locally resonant meta-beam incorporating a softening nonlinear factor.An improved camroller structure is designed in this meta-beam to achieve the softening nonlinear stiffness of the local oscillators.Firstly,based on Hamilton's principle and the Galerkin method,the control equations for the coupled system are established.The theoretical band gap boundary is then derived with the modal analysis method.The theoretical results reveal that the band gap of the meta-beam shifts towards lower frequencies due to the presence of a softening nonlinear factor,distinguishing it from both linear metamaterials and those with hardening nonlinear characteristics.Then,the vibration attenuation characteristics of a finite size meta-beam are investigated through numerical calculation,and are verified by the theoretical results.Furthermore,parameter studies indicate that the reasonable design of the local oscillator parameters based on lightweight principles helps to achieve further broadband and efficient vibration reduction in the low-frequency region.Finally,a prototype of the meta-beam is fabricated and assembled,and the formations of the low-frequency band gap and the amplitude-induced band gap phenomenon are verified through experiments.展开更多
This study proposed a new and more flexible S-shaped rock damage evolution model from a phenomenological perspective based on an improved Logistic function to describe the characteristics of the rock strain softening ...This study proposed a new and more flexible S-shaped rock damage evolution model from a phenomenological perspective based on an improved Logistic function to describe the characteristics of the rock strain softening and damage process.Simultaneously,it established a constitutive model capable of describing the entire process of rock pre-peak compaction and post-peak strain softening deformation,considering the nonlinear effects of the initial compaction stage of rocks,combined with damage mechanics theory and effective medium theory.In addition,this research verified the rationality of the constructed damage constitutive model using results from uniaxial and conventional triaxial compression tests on Miluo granite,yellow sandstone,mudstone,and glutenite.The results indicate that based on the improved Logistic function,the theoretical damage model accurately describes the entire evolution of damage characteristics during rock compression deformation,from maintenance through gradual onset,accelerated development to deceleration and termination,in a simple and unified expression.At the same time,the constructed constitutive model can accurately simulate the stress-strain process of different rock types under uniaxial and conventional triaxial compression,and the theoretical model curve closely aligns with experimental data.Compared to existing constitutive models,the proposed model has significant advantages.The damage model parameters a,r and β have clear physical meanings and interact competitively,where the three parameters collectively determine the shape of the theoretical stress−strain curve.展开更多
Existing creep constitutive models rarely incorporate studies on the coupling mechanism between creep damage and rock strain softening/hardening.This study analyzed the strain softening and hardening behaviors of argi...Existing creep constitutive models rarely incorporate studies on the coupling mechanism between creep damage and rock strain softening/hardening.This study analyzed the strain softening and hardening behaviors of argillaceous sandstone and sandy mudstone during load-induced failure based on the plastic increment theory.These behaviors were then coupled with an improved Burgers creep model to establish a coupled creep-damage and plastic softening/hardening model.Finally,the validity and engineering applicability of the proposed model were verified through FLAC~(3D)numerical simulations.The numerical simulation results of standard cylindrical specimens show that the established coupling model can effectively reflect the unloading creep deformation law and failure characteristics of argillaceous sandstone and sandy mudstone.Taking the diversion tunnel of a hydropower station in Northwest China as an example for engineering application,the coupled creep-damage and plastic softening/hardening model is introduced into FLAC~(3D)to carry out numerical simulation calculation of the tunnel under excavation and unsupported creep conditions.The results show that the uncoordinated deformation of the upper and lower walls of the surrounding rock of the tunnel is more prominent.When the buried depth of the tunnel increases to 80 m,the monitoring point C in the sandy mudstone area of the upper wall shows nonlinear accelerated deformation under unsupported creep conditions,and the maximum displacement in the horizontal direction reaches 44.5 mm,and the maximum displacement in the vertical direction reaches 53.5 mm.The coupled creep-damage and plastic softening/hardening model established in the research results can well describe the whole process of uncoordinated deformation and failure in the unloading creep process of soft-hard interbedded rock mass.展开更多
Multi-pass hot processing methods are commonly used in magnesium(Mg)alloys to overcome the poor workability due to limited slip systems,which generally involve complicated post-deformation softening and hardening beha...Multi-pass hot processing methods are commonly used in magnesium(Mg)alloys to overcome the poor workability due to limited slip systems,which generally involve complicated post-deformation softening and hardening behaviors.In this work,to reveal post-deformation softening and hardening mechanisms of a Mg-2Y-1Zn alloy,double-stage hot compression tests and microstructural observations were conducted.The results showed that the softening fraction of Mg-2Y-1Zn alloy showed a non-linear dependence on deformation conditions and could be general coupled by Z parameter.Due to the formation and cross-overlapping of twins and kinks,only static recovery(SRV)occurred during holding process at 300℃/0.001 s^(-1) which led to the least static softening:5.52% after 10 s of holding.For samples at 400℃/0.001s^(-1),the enhanced post-deformation softening,which is 11.93% after 10 s of holding,was attributed to static recrystallization(SRX)followed continuous dynamic recrystallization(CDRX)happened during first deformation stage as well as SRV influenced by the LPSO phases.Under deformation condition of 400℃/0.1 s^(-1),the coupled meta-dynamic recrystallization(MDRX)and SRX resulted in serious stress relaxation,which is 42.83% after 10 s of holding,and caused hardening phenomenon at reloading stage.The 18R-LPSO and 14H-LPSO phases synchronously worked on deformation behaviors and limited the growth of recrystallized grains.Further,a simplified static softening kinetics model was established based on Johnson-Mehl-Avrami-Kolmogorov equation and employed to rationalize experimental data.展开更多
The flow stress behavior and microstructure development of Al-5Zn-2Mg （7005） aluminum alloy were studied by hot compression tests at deformation temperatures between 300-500 ＆#176;C and strain rates between 0.05-50...The flow stress behavior and microstructure development of Al-5Zn-2Mg （7005） aluminum alloy were studied by hot compression tests at deformation temperatures between 300-500 ＆#176;C and strain rates between 0.05-50 s-1. The deformed structures of the samples were observed by optical microscopy （OM）, transmission electron microscopy （TEM） and electron backscattering diffraction （EBSD） analysis. The calculated activation energy is 147 kJ/mol, which is very close to the activation energy for lattice self-diffusion in aluminum （142 kJ/mol）. Dynamic recovery is the dominant restoration mechanism during the deformation. At high strain rate of 50 s-1, temperature rise due to deformation heating leads to a significant flow softening. Microstructure observations indicated that the remaining softening after deformation heating correction at high strain rate and the softening observed at high temperature are associated with grain coarsening induced by grain boundary migration during dynamic recovery process.展开更多
The effects of the deformation temperature and the strain rate on the hot deformation behavior of pure copper were investigated based on compression tests. The expressions of strain hardening rate, dynamic recrystalli...The effects of the deformation temperature and the strain rate on the hot deformation behavior of pure copper were investigated based on compression tests. The expressions of strain hardening rate, dynamic recrystallization critical stress, saturated stress, dynamic recovery volume fraction and dynamic recrystallization volume fraction were determined. According to the processing map, the instability regions occur in regions of 400?450 °C, 0.001?0.05 s?1 and 450?750 °C, 0.05?1 s?1. The deformation mechanism in the stability region is dynamic recrystallization. The flow stress was predicted. The results also show that the true stress–true strain curves predicted by the extracted model are in good agreement with the experimental results.展开更多
Kiwifruit (Actinidia deliciosa (A. Chev.) C. F. Liang et A. R. Ferguson cv. Bruno) was used toinvestigate the effects of acetylsalicylic acid (ASA, 1.0 mmol/L, pH 3.5) and ethylene (100 mL/L) treat-ments on changes at...Kiwifruit (Actinidia deliciosa (A. Chev.) C. F. Liang et A. R. Ferguson cv. Bruno) was used toinvestigate the effects of acetylsalicylic acid (ASA, 1.0 mmol/L, pH 3.5) and ethylene (100 mL/L) treat-ments on changes at endogenous salicylic acid (SA) levels and other senescence-related factors duringfruit ripening and softening at 20 ℃. The level of endogenous SA in ripening fruits declined and a closerelationship was observed between the change at endogenous SA level and the rate of fruit ripening andsoftening. ASA treatment elevated SA level in the fruit, slowed down the increases in lipoxygenase (LOX)and allene oxide synthase (AOS) activities, decreased the O22-. production in the preclimacteric phase andthe early phase of ethylene climacteric rise, maintained the stability of cell membrane, inhibited ethylenebiosynthesis, postponed the onset of the ethylene climacteric, and delayed the process of fruit ripeningand softening. On the contrary, application of ethylene to ripening kiwifruit resulted at a lower SA level, anaccelerated increases in the activities of LOX and AOS and the rate of O22-. production, an elevated relativeelectric conductivity and an advanced onset of ethylene climacteric, and a quicker fruit ripening andsoftening. It is suggested that the effects of ASA on ripening kiwifruit can be attributed to its ability toscavenge O22-. and/or to maintain stability of cell membrane.展开更多
A required finite element method（FEM） model applicable for narrow gap CMT and CMT＋P MIX welding was established based on the interactions between arc,base metal and filler metal.A novel method of simplifying wire f...A required finite element method（FEM） model applicable for narrow gap CMT and CMT＋P MIX welding was established based on the interactions between arc,base metal and filler metal.A novel method of simplifying wire feeding pulses and heat input pulses was supposed under the conduction of equivalent input.The method together with composed double-ellipse heat sources was included in the model.The model was employed in the investigation of thermal cycling and the identification of the softened zone of AA7A52 base plates.Low-frequency behavior emerged in the form of low-cooling rate sects,which were not expected under experimental conditions.The softened zone including the quenched zone and averaging zone of the base plate was much wider internal the base plate than that close to the surfaces.The reliability of the predictions in thermal cycling was supported by infrared imaging test results of the thermal cycle process.展开更多
An Al2O3 dispersion strengthened(ADS)alloy with an ultra-high softening temperature of∼1200 K was fabricated by the in-situ internal oxidation and reduction methods.The evolution of the nanometer Al2O3 particles,grai...An Al2O3 dispersion strengthened(ADS)alloy with an ultra-high softening temperature of∼1200 K was fabricated by the in-situ internal oxidation and reduction methods.The evolution of the nanometer Al2O3 particles,grain size,and consequently the softening behavior of this ADS alloy,were investigated by conducting the annealing treatments in the range from 673 K to 1273 K for 60 min.These refined nanometer Al2O3 particles were found to be highly stable at elevated temperatures,leading to the high dislocation density and grain boundary stability of the matrix.The average grain size was found to increase extremely slowly from∼0.60μm to∼0.74μm with increasing annealing temperatures from 773 K to 1273 K.A criterion for grain boundaries migration and softening was established based on the competition between grain growth and pinning effect of Al2O3 particles.The strong pinning effect of Al2O3 particles was found when the grain size was between the lower limit(about 0.4-0.5μm)and upper limit(2.18μm).The occurrence of softening behavior was attributed to the rapid increase of the proportion of grains larger than the upper limit.A modified Hall-Petch relationship was established by introducing the integration of the grain size distribution,which can describe this correlation between softening behavior and the pinning effect of Al2O3 particles.The current study not only sheds light on the further understanding of the softening mechanism of ADS copper alloy but also provides a useful route for designing copper alloy with high softening resistance.展开更多
The coal mining process is afected by various water sources such as groundwater and coal seam water injection.Understanding the dynamic mechanical parameters of water-immersed coal is helpful for coalmine safe product...The coal mining process is afected by various water sources such as groundwater and coal seam water injection.Understanding the dynamic mechanical parameters of water-immersed coal is helpful for coalmine safe production.The impact compression tests were performed on coal with diferent moisture contents by using theϕ50 mm Split Hopkinson Pressure Bar(SHPB)experimental system,and the dynamic characteristics and energy loss laws of water-immersed coal with diferent compositions and water contents were analyzed.Through analysis and discussion,it is found that:(1)When the moisture content of the coal sample is 0%,30%,60%,the stress,strain rate and energy frst increase and then decrease with time.(2)When the moisture content of the coal sample increases from 30%to 60%,the stress“plateau”of the coal sample becomes more obvious,resulting in an increase in the compressive stress stage and a decrease in the expansion stress stage.(3)The increase of moisture content of the coal sample will afect its impact deformation and failure mode.When the moisture content is 60%,the incident rod end and the transmission rod end of the coal sample will have obvious compression failure,and the middle part of the coal sample will also experience expansion and deformation.(4)The coal composition ratio suitable for the coal immersion softening impact experiment is optimized.展开更多
The dynamic response of a strain-softening beam subjected to a transverse impulsive on its tip is investigated.A softening moment-curvature relation is assumed for the beam and a closed form solution is obtained for a...The dynamic response of a strain-softening beam subjected to a transverse impulsive on its tip is investigated.A softening moment-curvature relation is assumed for the beam and a closed form solution is obtained for a special kind of load,which shows that there exists a softening region in the beam and this re- gion propagates along the beam.This result indicates that,except for the possible discrete softening points with rotation discontinuity caused by the deformation localization,the existence of the softening region and its travelling along the beam are the essential features of the dynamic response of a strain-softening beam.The results also show that the failure of the beam should take place under a special load and the critical condition on which the dynamic failure occurs is given.展开更多
The effect of sinter with different MgO contents on the softening-melting behavior of mixed burden made from chro- mium-bearing vanadium-titanium magnetite was investigated. The results show that with increasing MgO c...The effect of sinter with different MgO contents on the softening-melting behavior of mixed burden made from chro- mium-bearing vanadium-titanium magnetite was investigated. The results show that with increasing MgO content in the sinter, the softening interval and melting interval increased and the location of the cohesive zone shifted downward slightly and became moderately thicker. The softening-melting characteristic value was less pronounced when the MgO content in the sinter was 2.98wt%-3.40wt%. Increasing MgO content in the sinter reduced the content and recovery of V and Cr in the dripped iron. In addition, greater MgO contents in the sinter resulted in the generation of greater amounts of high-melting-point components, which adversely affected the permeability of the mixed burden. When the softening-melting behavior of the mixed burden and the recovery of valuable elements were taken into account, proper MgO con- tents in the sinter and slag ranged from 2.98wt% to 3.40wt% and from 11.46wt% to 12.72wt%, respectively, for the smelting of burden made from chromium-bearing vanadium-titanium magnetite in a blast furnace.展开更多
The aging behavior of softening composite solid propellant was investigated by measuring its mechanical and ballistic prosperities during prolonged storage at elevated and room temperatures. Accelerated aging was cond...The aging behavior of softening composite solid propellant was investigated by measuring its mechanical and ballistic prosperities during prolonged storage at elevated and room temperatures. Accelerated aging was conducted at 65 °C for 231 days while the normal aging was performed at 25 ± 3 °C and relative humidity less than 50% for 8 years. The mechanical properties were obtained from uniaxial tensile tests for the aged propellant specimens while the ballistic properties were determined from static firing tests of subscale motors aged for 112 days at 65 °C. The mechanical results show that the maximum tensile strength and Young's modulus initially increase and subsequently decrease with increasing aging time, while the maximum tensile strain generally increases with increasing aging time. The ballistic properties like burning rate show a small change which cannot affect the ballistic performance. The experimental results show that the changes in the mechanical properties are significant during the aging period, but the burning rate does not undergo significant changes. From this study, it is observed that the propellant ages through a combination of reactions like post-cure, oxidative cross-linking, chain scission, and hydrolysis. The chain scission and the hydrolysis effect are the most significant process, which makes the propellant soft and extendible. The observed aging mechanism has been modeled using an exponential function with two terms which can describe the complex behavior of the aging. By applying Arrhenius equation,the activation energy values were obtained based on the propellant mechanical properties. The shelf life of this propellant formulation at 25 °C is predicted to be 13 years using the modulus as failure criteria and control parameter.展开更多
The behaviors of mixed burden in the cohesive zone of oxygen blast furnace were studied by softening and melting tests, and the influence of reducing gas and burden basicity on the softening and melting behaviors of m...The behaviors of mixed burden in the cohesive zone of oxygen blast furnace were studied by softening and melting tests, and the influence of reducing gas and burden basicity on the softening and melting behaviors of mixed burden was also investigated. The results indicated that the softening range became wide, however, the melting range narrowed sharply in the atmosphere of oxygen blast furnace. The permeability of burden in the oxygen blast furnace was obviously improved comparing with the conventional blast furnace. In addition, the content of sulphur in the dripping iron of oxygen blast furnace was much lower than that of conventional blast furnace, however, the content of carbon increased. An optimum basicity of burden, which could lead to the appearance of the narrower melting range and better permeability of burden, was obtained in the atmosphere of oxygen blast furnace.展开更多
To better understand the mechanism of the strength weakening process of soft rocks in deep mines after interacting with water, a self-developed experimental system, Intelligent Testing System for Water Absorption in D...To better understand the mechanism of the strength weakening process of soft rocks in deep mines after interacting with water, a self-developed experimental system, Intelligent Testing System for Water Absorption in Deep Soft Rocks （ITSWADSR）, is employed to analyze the hydrophilic behavior of deep calcareous shale sampled from Daqiang coal mine. Experimental results demonstrate that the relation between water absorption and time can be expressed by power functions, and the soakage rate decreases while the soakage increases with time. In order to quantitatively calculate the weight coefficients of the influential factors for water absorbing capacity of rocks, a series of testing methods are adopted, including scanning electron microscope （SEM）, X-ray diffraction and mercury injection test. It is demonstrated that the effective porosity has a positive correlation with the water absorbing capacity of rocks and the contents of illite and illite/smectite. The initial water content presents a negative correlation with the water absorption capacity of rocks. According to the absolute value of weight coefficients of various influential factors, the order of magnitude from high to low is captured： initial water content, illite, illite/smectite formation （S=5%）, and the effective porosity. After water absorption tests, uniaxial compressive strength （UCS） tests were performed on rock specimens allowing a linear relationship between the UCS and the water content of rock to be established, indicating that the strength of calcareous shale decreases linearly with the increasing water content.展开更多
Considering the influence of strain softening, the solutions of stress, displacement, plastic softening region radius and plastic residual region radius were derived for circular openings in nonlinear rock masses subj...Considering the influence of strain softening, the solutions of stress, displacement, plastic softening region radius and plastic residual region radius were derived for circular openings in nonlinear rock masses subjected to seepage. The radial stress distribution curve, ground reaction curve, and relation curve between plastic softening region radius and supporting force in three different conditions were drawn respectively. From the comparisons among these results for different conditions, it is found that when the supporting force is the same, the displacement of tunnel wall considering both seepage and strain softening is 85.71% greater than that only considering seepage. The increase values of radial displacement at 0.95 m and plastic softening region radius at 6.6 m show that the seepage and strain softening have the most unfavorable effects on circular opening stability in strain softening rock masses.展开更多
A new method was proposed to predict the limited compaction grouting pressure for the soft soils. Theoretical basis of the method considered the conical shear failure above the grout bulb. Using the Mohr-Coulomb yield...A new method was proposed to predict the limited compaction grouting pressure for the soft soils. Theoretical basis of the method considered the conical shear failure above the grout bulb. Using the Mohr-Coulomb yield criterion as the initial yield function, the limited compaction grouting pressure was determined, according to the softening elastic-plastic model based on the conventional triaxial compression tests to simulate the strain softening soils. The small strain in the elastic zone and large stain in the plastic zone and the rational yield function for the strain softening phase stage, the analytical solutions to the compaction grouting pressure were presented. The results indicate reasonable agreement and show a good potential of the proposed method for rationally optimizing the design of compaction grouting operations.展开更多
基金the financial support received from the UK Engineering and Physical Sciences Research Council(EPSRC)through project grants EP/W010089/1 and EP/T005254/1.
文摘With the generation of both localised thermal and vibration in incremental sheet forming(ISF)by novel tool designs,rotational vibration assisted ISF(RV-ISF)can achieve significant force reduction and material softening.However,the combined thermal and vibration softening in RV-ISF is unclear.By evaluating the similarities and differences of friction stir ISF(FS-ISF)and RV-ISF,this study develops a novel approach to decouple and quantify the thermal and vibration softening effects in RV-ISF of AZ31B-H24,providing new insights into underlying thermal and vibration softening mechanism.Experimental results reveal that in RV-ISF of AZ31B-H24 the thermal softening due to frictional heating dominates with 45∼65%of softening,while the vibration effect only contributes up to 15%of softening,from the conventional ISF,depending on the tool designs and tool rotational speed.The double-offset tool(T2)produces greater vibration softening than the three-groove tool(T3)owing to the higher vibration amplitude of the T2 tool.An increase in tool rotational speed primarily enhances thermal softening with only marginal changes to the vibration effect.Microstructural analysis suggests that with average grain size of 0.94μm at the top layer,RV-ISF with T3 and 3000 rpm is more effective for microstructure refinement than that by FS-ISF,especially on the tool-sheet contact surface,which confirms the occurrence of surface shearing.This refinement is a result of the reduced recrystallisation degree,71.8%at the top bottom layer.Compared with FS-ISF,RV-ISF can lead to not only higher geometrically necessary dislocation density,but also higher fraction of low-angle grain boundaries,indicating that softening mechanism due to localised vibration effect is resulted from the enhanced rearrangement and annihilation of dislocations.These findings contribute to new understanding of the thermal and vibration softening effects in RV-ISF of AZ31B-H24 and offer a theoretical foundation for the tool design and process optimisation.
基金supported by the Natural Science Foundation of Heilongjiang Province(No.JQ2022E004).
文摘In this paper,the work hardening and softening behavior of AZ31 magnesium alloy sheets by hard plate accumulative roll bonding(HP-ARB)process in a specific temperature range was studied for the first time,and the cyclic stress relaxation test,EBSD,TEM and other characterization methods were used.When the rolling temperature is 350℃,the grain size of magnesium sheets is refined to 4.32(±0.36)μm on average,and it shows an excellent combination of strength and plasticity.The tensile strength reaches 307(±8.52)MPa and the elongation is 12.73(±0.84)%.At this time,the curve of work hardening rate decreases smoothly and the degree of hardening is the lowest,and the amplitude of stress drop △σ_(p) in work softening test is the smallest with the increase of cycle times,which shows that the well coordination between work hardening and softening behavior has been achieved.Research has found that the combined effect of grain boundary strengthening and fine grain strengthening enhances the yield and tensile strength of magnesium sheets after three passes HP-ARB process at 350℃.This is attributed to the high degree of dislocation slip opening in the pyramidal surfaceand<c+a>,which not only coordinates the c-axis strain of the entire grain,but also promotes the slip transfer of dislocations in the fine-grained region,significantly improving the elongation of the sheets.This study provides a new idea for the forming and manufacturing of high performance magnesium alloy sheets.
基金supported by the“National Natural Science Foundation of China”(Grants.52271109 and 52001223)Support from the“National Key Research and Development Program for Young Scientists”(Grant.2021YFB3703300)+1 种基金the Major Special Plan for Science and Technology in Shanxi Province(202201050201012)the Special Fund Project for Guiding Local Science and Technology Development by the Central Government(Grant.YDZJSX2021B019)。
文摘To obtain the Ti_(p)with different aspect ratios,the Ti_(p)/Mg-5Zn-0.3Ca composite prepared by semi-solid stir casting was subjected to extrusion at 220℃,180℃,and 140℃,respectively.Then,the effect of the Ti_(p)’s aspect ratio on the microstructure,mechanical properties,work hardening and softening behaviors of Ti_(p)/Mg-5Zn-0.3Ca composites was investigated.The results indicated that the Ti_(p)could be elongated obviously after low-temperature extrusion,and the aspect ratio of which would reach to 13.7:1 as the extrusion temperature deceased to 140℃.Then the“Ti/Mg”layer-like structure was formed in the Ti_(p)/Mg-5Zn-0.3Ca composite.Accompanied with the elongation of Ti_(p),the dynamic recrystallized grains and dynamic precipitates were both refined significantly,however,the dynamic recrystallization rate changed a little.The elongated Ti_(p)endowed the Ti_(p)/Mg-5Zn-0.3Ca composites with better matching of strength and toughness without the sacrifice of elongation and bending strain.Both the work hardening rate and softening rate of Ti_(p)/Mg-5Zn-0.3Ca composites increased with the increasing aspect ratio of Ti_(p).The formation of“Ti/Mg”layer-like structure contributed to the redistribution of strain from large aggregations to a network-like distribution,which effectively suppresses the initiation and propagation of micro-cracks,thus enhancing the plasticity of the Ti_(p)/Mg-5Zn-0.3Ca composites.
基金supported by the National Natural Science Foundation of China(Nos.12172014,U224126412332001)。
文摘In order to obtain a lower frequency band gap,this paper proposes a novel locally resonant meta-beam incorporating a softening nonlinear factor.An improved camroller structure is designed in this meta-beam to achieve the softening nonlinear stiffness of the local oscillators.Firstly,based on Hamilton's principle and the Galerkin method,the control equations for the coupled system are established.The theoretical band gap boundary is then derived with the modal analysis method.The theoretical results reveal that the band gap of the meta-beam shifts towards lower frequencies due to the presence of a softening nonlinear factor,distinguishing it from both linear metamaterials and those with hardening nonlinear characteristics.Then,the vibration attenuation characteristics of a finite size meta-beam are investigated through numerical calculation,and are verified by the theoretical results.Furthermore,parameter studies indicate that the reasonable design of the local oscillator parameters based on lightweight principles helps to achieve further broadband and efficient vibration reduction in the low-frequency region.Finally,a prototype of the meta-beam is fabricated and assembled,and the formations of the low-frequency band gap and the amplitude-induced band gap phenomenon are verified through experiments.
基金Project(52074299)supported by the National Natural Science Foundation of ChinaProjects(2023JCCXSB02,BBJ2024083)supported by the Fundamental Research Funds for the Central Universities,China。
文摘This study proposed a new and more flexible S-shaped rock damage evolution model from a phenomenological perspective based on an improved Logistic function to describe the characteristics of the rock strain softening and damage process.Simultaneously,it established a constitutive model capable of describing the entire process of rock pre-peak compaction and post-peak strain softening deformation,considering the nonlinear effects of the initial compaction stage of rocks,combined with damage mechanics theory and effective medium theory.In addition,this research verified the rationality of the constructed damage constitutive model using results from uniaxial and conventional triaxial compression tests on Miluo granite,yellow sandstone,mudstone,and glutenite.The results indicate that based on the improved Logistic function,the theoretical damage model accurately describes the entire evolution of damage characteristics during rock compression deformation,from maintenance through gradual onset,accelerated development to deceleration and termination,in a simple and unified expression.At the same time,the constructed constitutive model can accurately simulate the stress-strain process of different rock types under uniaxial and conventional triaxial compression,and the theoretical model curve closely aligns with experimental data.Compared to existing constitutive models,the proposed model has significant advantages.The damage model parameters a,r and β have clear physical meanings and interact competitively,where the three parameters collectively determine the shape of the theoretical stress−strain curve.
基金funded by the Natural Science Foundation of China(Grant No.U22A20600)。
文摘Existing creep constitutive models rarely incorporate studies on the coupling mechanism between creep damage and rock strain softening/hardening.This study analyzed the strain softening and hardening behaviors of argillaceous sandstone and sandy mudstone during load-induced failure based on the plastic increment theory.These behaviors were then coupled with an improved Burgers creep model to establish a coupled creep-damage and plastic softening/hardening model.Finally,the validity and engineering applicability of the proposed model were verified through FLAC~(3D)numerical simulations.The numerical simulation results of standard cylindrical specimens show that the established coupling model can effectively reflect the unloading creep deformation law and failure characteristics of argillaceous sandstone and sandy mudstone.Taking the diversion tunnel of a hydropower station in Northwest China as an example for engineering application,the coupled creep-damage and plastic softening/hardening model is introduced into FLAC~(3D)to carry out numerical simulation calculation of the tunnel under excavation and unsupported creep conditions.The results show that the uncoordinated deformation of the upper and lower walls of the surrounding rock of the tunnel is more prominent.When the buried depth of the tunnel increases to 80 m,the monitoring point C in the sandy mudstone area of the upper wall shows nonlinear accelerated deformation under unsupported creep conditions,and the maximum displacement in the horizontal direction reaches 44.5 mm,and the maximum displacement in the vertical direction reaches 53.5 mm.The coupled creep-damage and plastic softening/hardening model established in the research results can well describe the whole process of uncoordinated deformation and failure in the unloading creep process of soft-hard interbedded rock mass.
基金supported by the National Natural Science Foundation of China(52174361,52074114)Science and Technology Innovation Program of Hunan Province(2023RC3106)+2 种基金Open Fund of the China Spallation Neutron Source Songshan Lake Science City(KFKT2023B13)Graduate Training and Innovation Practice Base of Hunan Province,China Scholarship Council(202106130051)Postgraduate Scientific Research Innovation Project of Hunan Province(QL20220100,QL20230094).
文摘Multi-pass hot processing methods are commonly used in magnesium(Mg)alloys to overcome the poor workability due to limited slip systems,which generally involve complicated post-deformation softening and hardening behaviors.In this work,to reveal post-deformation softening and hardening mechanisms of a Mg-2Y-1Zn alloy,double-stage hot compression tests and microstructural observations were conducted.The results showed that the softening fraction of Mg-2Y-1Zn alloy showed a non-linear dependence on deformation conditions and could be general coupled by Z parameter.Due to the formation and cross-overlapping of twins and kinks,only static recovery(SRV)occurred during holding process at 300℃/0.001 s^(-1) which led to the least static softening:5.52% after 10 s of holding.For samples at 400℃/0.001s^(-1),the enhanced post-deformation softening,which is 11.93% after 10 s of holding,was attributed to static recrystallization(SRX)followed continuous dynamic recrystallization(CDRX)happened during first deformation stage as well as SRV influenced by the LPSO phases.Under deformation condition of 400℃/0.1 s^(-1),the coupled meta-dynamic recrystallization(MDRX)and SRX resulted in serious stress relaxation,which is 42.83% after 10 s of holding,and caused hardening phenomenon at reloading stage.The 18R-LPSO and 14H-LPSO phases synchronously worked on deformation behaviors and limited the growth of recrystallized grains.Further,a simplified static softening kinetics model was established based on Johnson-Mehl-Avrami-Kolmogorov equation and employed to rationalize experimental data.
基金Project(51075132)supported by the National Natural Science Foundation of ChinaProject(20090161110027)supported by the Doctoral Fund of Ministry of Education of ChinaProject(2011BAG03B02)supported by National Key Technology R&D Program during the 12th Five-Year Plan Period,China
文摘The flow stress behavior and microstructure development of Al-5Zn-2Mg （7005） aluminum alloy were studied by hot compression tests at deformation temperatures between 300-500 ＆#176;C and strain rates between 0.05-50 s-1. The deformed structures of the samples were observed by optical microscopy （OM）, transmission electron microscopy （TEM） and electron backscattering diffraction （EBSD） analysis. The calculated activation energy is 147 kJ/mol, which is very close to the activation energy for lattice self-diffusion in aluminum （142 kJ/mol）. Dynamic recovery is the dominant restoration mechanism during the deformation. At high strain rate of 50 s-1, temperature rise due to deformation heating leads to a significant flow softening. Microstructure observations indicated that the remaining softening after deformation heating correction at high strain rate and the softening observed at high temperature are associated with grain coarsening induced by grain boundary migration during dynamic recovery process.
基金Project(cstc2015jcyj BX0115)supported by the Chongqing Research Program of Basic Research and Frontier Technology,China
文摘The effects of the deformation temperature and the strain rate on the hot deformation behavior of pure copper were investigated based on compression tests. The expressions of strain hardening rate, dynamic recrystallization critical stress, saturated stress, dynamic recovery volume fraction and dynamic recrystallization volume fraction were determined. According to the processing map, the instability regions occur in regions of 400?450 °C, 0.001?0.05 s?1 and 450?750 °C, 0.05?1 s?1. The deformation mechanism in the stability region is dynamic recrystallization. The flow stress was predicted. The results also show that the true stress–true strain curves predicted by the extracted model are in good agreement with the experimental results.
文摘Kiwifruit (Actinidia deliciosa (A. Chev.) C. F. Liang et A. R. Ferguson cv. Bruno) was used toinvestigate the effects of acetylsalicylic acid (ASA, 1.0 mmol/L, pH 3.5) and ethylene (100 mL/L) treat-ments on changes at endogenous salicylic acid (SA) levels and other senescence-related factors duringfruit ripening and softening at 20 ℃. The level of endogenous SA in ripening fruits declined and a closerelationship was observed between the change at endogenous SA level and the rate of fruit ripening andsoftening. ASA treatment elevated SA level in the fruit, slowed down the increases in lipoxygenase (LOX)and allene oxide synthase (AOS) activities, decreased the O22-. production in the preclimacteric phase andthe early phase of ethylene climacteric rise, maintained the stability of cell membrane, inhibited ethylenebiosynthesis, postponed the onset of the ethylene climacteric, and delayed the process of fruit ripeningand softening. On the contrary, application of ethylene to ripening kiwifruit resulted at a lower SA level, anaccelerated increases in the activities of LOX and AOS and the rate of O22-. production, an elevated relativeelectric conductivity and an advanced onset of ethylene climacteric, and a quicker fruit ripening andsoftening. It is suggested that the effects of ASA on ripening kiwifruit can be attributed to its ability toscavenge O22-. and/or to maintain stability of cell membrane.
基金Project (9140C850205120C8501) supported by the Major Program of National Key Laboratory of Remanufacturing and the Army Foundation Project of China
文摘A required finite element method（FEM） model applicable for narrow gap CMT and CMT＋P MIX welding was established based on the interactions between arc,base metal and filler metal.A novel method of simplifying wire feeding pulses and heat input pulses was supposed under the conduction of equivalent input.The method together with composed double-ellipse heat sources was included in the model.The model was employed in the investigation of thermal cycling and the identification of the softened zone of AA7A52 base plates.Low-frequency behavior emerged in the form of low-cooling rate sects,which were not expected under experimental conditions.The softened zone including the quenched zone and averaging zone of the base plate was much wider internal the base plate than that close to the surfaces.The reliability of the predictions in thermal cycling was supported by infrared imaging test results of the thermal cycle process.
基金financially supported by the National Key Research and Development Program of China(No.2020YFB0311101)the National Natural Science Foundation of China(Nos.92066205 and 92266301)+1 种基金the Natural Science Foundation for Distinguished Young Scholars of China(No.51925401)the Youth Foundation of National Natural Science Foundation China(No.52001020).
文摘An Al2O3 dispersion strengthened(ADS)alloy with an ultra-high softening temperature of∼1200 K was fabricated by the in-situ internal oxidation and reduction methods.The evolution of the nanometer Al2O3 particles,grain size,and consequently the softening behavior of this ADS alloy,were investigated by conducting the annealing treatments in the range from 673 K to 1273 K for 60 min.These refined nanometer Al2O3 particles were found to be highly stable at elevated temperatures,leading to the high dislocation density and grain boundary stability of the matrix.The average grain size was found to increase extremely slowly from∼0.60μm to∼0.74μm with increasing annealing temperatures from 773 K to 1273 K.A criterion for grain boundaries migration and softening was established based on the competition between grain growth and pinning effect of Al2O3 particles.The strong pinning effect of Al2O3 particles was found when the grain size was between the lower limit(about 0.4-0.5μm)and upper limit(2.18μm).The occurrence of softening behavior was attributed to the rapid increase of the proportion of grains larger than the upper limit.A modified Hall-Petch relationship was established by introducing the integration of the grain size distribution,which can describe this correlation between softening behavior and the pinning effect of Al2O3 particles.The current study not only sheds light on the further understanding of the softening mechanism of ADS copper alloy but also provides a useful route for designing copper alloy with high softening resistance.
基金This research was funded by the National Natural Science Foundation of China(51974176,51934004)ShandongProvince Natural Science Foundation of Outstanding Youth Fund(ZR2020JQ22)+1 种基金Shandong Province Colleges and Universities Youth Innovation and Technology Support Program(2019KJH006)Taishan Scholars Project(TS20190935).
文摘The coal mining process is afected by various water sources such as groundwater and coal seam water injection.Understanding the dynamic mechanical parameters of water-immersed coal is helpful for coalmine safe production.The impact compression tests were performed on coal with diferent moisture contents by using theϕ50 mm Split Hopkinson Pressure Bar(SHPB)experimental system,and the dynamic characteristics and energy loss laws of water-immersed coal with diferent compositions and water contents were analyzed.Through analysis and discussion,it is found that:(1)When the moisture content of the coal sample is 0%,30%,60%,the stress,strain rate and energy frst increase and then decrease with time.(2)When the moisture content of the coal sample increases from 30%to 60%,the stress“plateau”of the coal sample becomes more obvious,resulting in an increase in the compressive stress stage and a decrease in the expansion stress stage.(3)The increase of moisture content of the coal sample will afect its impact deformation and failure mode.When the moisture content is 60%,the incident rod end and the transmission rod end of the coal sample will have obvious compression failure,and the middle part of the coal sample will also experience expansion and deformation.(4)The coal composition ratio suitable for the coal immersion softening impact experiment is optimized.
基金The project supported by National Natural Science Foundation of China
文摘The dynamic response of a strain-softening beam subjected to a transverse impulsive on its tip is investigated.A softening moment-curvature relation is assumed for the beam and a closed form solution is obtained for a special kind of load,which shows that there exists a softening region in the beam and this re- gion propagates along the beam.This result indicates that,except for the possible discrete softening points with rotation discontinuity caused by the deformation localization,the existence of the softening region and its travelling along the beam are the essential features of the dynamic response of a strain-softening beam.The results also show that the failure of the beam should take place under a special load and the critical condition on which the dynamic failure occurs is given.
基金the National Natural Science Foundation of China (51574067)the National High Technology Research and Development Program of China (2012AA062302 and 2012AA062304)the Fundamental Research Funds for the Central Universities of China (N110202001)
文摘The effect of sinter with different MgO contents on the softening-melting behavior of mixed burden made from chro- mium-bearing vanadium-titanium magnetite was investigated. The results show that with increasing MgO content in the sinter, the softening interval and melting interval increased and the location of the cohesive zone shifted downward slightly and became moderately thicker. The softening-melting characteristic value was less pronounced when the MgO content in the sinter was 2.98wt%-3.40wt%. Increasing MgO content in the sinter reduced the content and recovery of V and Cr in the dripped iron. In addition, greater MgO contents in the sinter resulted in the generation of greater amounts of high-melting-point components, which adversely affected the permeability of the mixed burden. When the softening-melting behavior of the mixed burden and the recovery of valuable elements were taken into account, proper MgO con- tents in the sinter and slag ranged from 2.98wt% to 3.40wt% and from 11.46wt% to 12.72wt%, respectively, for the smelting of burden made from chromium-bearing vanadium-titanium magnetite in a blast furnace.
文摘The aging behavior of softening composite solid propellant was investigated by measuring its mechanical and ballistic prosperities during prolonged storage at elevated and room temperatures. Accelerated aging was conducted at 65 °C for 231 days while the normal aging was performed at 25 ± 3 °C and relative humidity less than 50% for 8 years. The mechanical properties were obtained from uniaxial tensile tests for the aged propellant specimens while the ballistic properties were determined from static firing tests of subscale motors aged for 112 days at 65 °C. The mechanical results show that the maximum tensile strength and Young's modulus initially increase and subsequently decrease with increasing aging time, while the maximum tensile strain generally increases with increasing aging time. The ballistic properties like burning rate show a small change which cannot affect the ballistic performance. The experimental results show that the changes in the mechanical properties are significant during the aging period, but the burning rate does not undergo significant changes. From this study, it is observed that the propellant ages through a combination of reactions like post-cure, oxidative cross-linking, chain scission, and hydrolysis. The chain scission and the hydrolysis effect are the most significant process, which makes the propellant soft and extendible. The observed aging mechanism has been modeled using an exponential function with two terms which can describe the complex behavior of the aging. By applying Arrhenius equation,the activation energy values were obtained based on the propellant mechanical properties. The shelf life of this propellant formulation at 25 °C is predicted to be 13 years using the modulus as failure criteria and control parameter.
基金Sponsored by National Basic Research Program(973Program) of China(2012CB720401)National Key Technology Research and Development Program in 12th Five-Year Plan of China(2011BAC01B02)
文摘The behaviors of mixed burden in the cohesive zone of oxygen blast furnace were studied by softening and melting tests, and the influence of reducing gas and burden basicity on the softening and melting behaviors of mixed burden was also investigated. The results indicated that the softening range became wide, however, the melting range narrowed sharply in the atmosphere of oxygen blast furnace. The permeability of burden in the oxygen blast furnace was obviously improved comparing with the conventional blast furnace. In addition, the content of sulphur in the dripping iron of oxygen blast furnace was much lower than that of conventional blast furnace, however, the content of carbon increased. An optimum basicity of burden, which could lead to the appearance of the narrower melting range and better permeability of burden, was obtained in the atmosphere of oxygen blast furnace.
基金Supported by the Key Basic Research Program of China(2006CB202200)the National Major Project of Ministry of Education of China(304005)
文摘To better understand the mechanism of the strength weakening process of soft rocks in deep mines after interacting with water, a self-developed experimental system, Intelligent Testing System for Water Absorption in Deep Soft Rocks （ITSWADSR）, is employed to analyze the hydrophilic behavior of deep calcareous shale sampled from Daqiang coal mine. Experimental results demonstrate that the relation between water absorption and time can be expressed by power functions, and the soakage rate decreases while the soakage increases with time. In order to quantitatively calculate the weight coefficients of the influential factors for water absorbing capacity of rocks, a series of testing methods are adopted, including scanning electron microscope （SEM）, X-ray diffraction and mercury injection test. It is demonstrated that the effective porosity has a positive correlation with the water absorbing capacity of rocks and the contents of illite and illite/smectite. The initial water content presents a negative correlation with the water absorption capacity of rocks. According to the absolute value of weight coefficients of various influential factors, the order of magnitude from high to low is captured： initial water content, illite, illite/smectite formation （S=5%）, and the effective porosity. After water absorption tests, uniaxial compressive strength （UCS） tests were performed on rock specimens allowing a linear relationship between the UCS and the water content of rock to be established, indicating that the strength of calcareous shale decreases linearly with the increasing water content.
基金Project(09JJ1008) supported by Hunan Provincial Science Foundation of ChinaProject(200550) supported by the Foundation for the Author of National Excellent Doctoral Dissertation of China
文摘Considering the influence of strain softening, the solutions of stress, displacement, plastic softening region radius and plastic residual region radius were derived for circular openings in nonlinear rock masses subjected to seepage. The radial stress distribution curve, ground reaction curve, and relation curve between plastic softening region radius and supporting force in three different conditions were drawn respectively. From the comparisons among these results for different conditions, it is found that when the supporting force is the same, the displacement of tunnel wall considering both seepage and strain softening is 85.71% greater than that only considering seepage. The increase values of radial displacement at 0.95 m and plastic softening region radius at 6.6 m show that the seepage and strain softening have the most unfavorable effects on circular opening stability in strain softening rock masses.
基金Project (200550) supported by the Foundation for the Author of National Excellent Doctoral Dissertation of ChinaProject (09JJ1008) supported by Hunan Provincial Natural Science Foundation of China
文摘A new method was proposed to predict the limited compaction grouting pressure for the soft soils. Theoretical basis of the method considered the conical shear failure above the grout bulb. Using the Mohr-Coulomb yield criterion as the initial yield function, the limited compaction grouting pressure was determined, according to the softening elastic-plastic model based on the conventional triaxial compression tests to simulate the strain softening soils. The small strain in the elastic zone and large stain in the plastic zone and the rational yield function for the strain softening phase stage, the analytical solutions to the compaction grouting pressure were presented. The results indicate reasonable agreement and show a good potential of the proposed method for rationally optimizing the design of compaction grouting operations.
