The aim of this study is to enhance the value of local earth materials used in the construction of certain homes in the Republic of Guinea. Thus, a trial study to improve the quality of mud bricks using paper fibers o...The aim of this study is to enhance the value of local earth materials used in the construction of certain homes in the Republic of Guinea. Thus, a trial study to improve the quality of mud bricks using paper fibers obtained by grinding and soaking in water and then drying were used as a stabilizer in the manufacture of these mud bricks from the sample of two sites Dounkiwal (DK) (in Mamou and the sample from the urban commune of Kouroussa). To do this, certain methods and means of identification were carried out, namely: geotechnical, mineralogical and chemical analyses. Sample DK from Mamou has a silty-clay geotechnical characteristic with a plasticity index Ip of 12.75%. However, mineralogical and chemical studies showed that sample Dounkiwal (DK) (Mamou) contains a high proportion of silica and iron oxides (79.63%) and Fe2O3 (11.85%), associated with other alkaline earth oxides and ions: CaO;MgO;SO32−;Cl−, i.e. 3.96%;0.96%;0.28% and 0.039% respectively. Its loss on ignition (LOI) and insoluble residues are 15.40% and 56.36%. The evaluation of the number of huts in Upper and Middle Guinea showed that the populations of these areas have been using mud bricks for several decades in the construction of dwellings. The average value found for the compressive strength of these bricks (from samples I, II and III from Kouroussa) is 0.16 MPa. This value is appreciable in the construction of mud houses.展开更多
This study was part of the framework that contributed not only to the improvement of thermal comfort in housing but also to the decarbonization of the construction and building materials industry. For this purpose, te...This study was part of the framework that contributed not only to the improvement of thermal comfort in housing but also to the decarbonization of the construction and building materials industry. For this purpose, terracotta brick seems to meet these needs. Thus, the objective of this work was to evaluate the influence of the incorporation of coal fly ash from a thermal power plant on the physical and mechanical properties of fired bricks from grey clay in the Thicky area of Senegal. The coal fly ash was incorporated into the raw clay material in proportions of 0, 5, 10, and 15 % by weight. These two raw materials were first characterized by X-ray fluorescence spectroscopy (XRF). The XRF analyses showed that the most abundant oxides in clay were SiO2 (55.034%) and Fe2O3 (10.155%). In coal fly ash, SiO2 (38.574%) is predominant. The ash also contained Al2O3 (7.717%) and alicano-earthy melting oxides such as CaO (9.271%) and MgO (7.298%) etc. These melting oxides were necessary to facilitate the formation of the liquid phase when baking platelets. The latter, when burned at a temperature of 880°C, were characterized by determining the number of physico-mechanical parameters, such as linear shrinkage during cooking, water absorption, fire loss and compressive strength. A Hierarchical Ascending Classification of these different parameters was performed and three classes were obtained. Class 1 with better compressive strength (6.358 MPa), was in sample A (5%). Class 2 consisted of sample D (reference) and had a higher plasticity index (28.51%) and water absorption rate (11.19%). Finally, class 3, which included samples B (10%) and C (15%), had very high shrinkage and fire losses compared to other platelets. These results highlighted the possibility of using up to 5% of the coal fly ash in the production of new fired bricks with good performance.展开更多
建立了由一个制造商和一个分销商组成的基于电子市场的二级供应链模型,讨论了分销商采用Bricks and Clicks模式分销产品,并在电子渠道进行季节后销售的情况,分析了供应链的契约协调问题及供应链成员的利润情况.研究发现改进的回购契约...建立了由一个制造商和一个分销商组成的基于电子市场的二级供应链模型,讨论了分销商采用Bricks and Clicks模式分销产品,并在电子渠道进行季节后销售的情况,分析了供应链的契约协调问题及供应链成员的利润情况.研究发现改进的回购契约可以使Bricks and Clicks分销模式下基于电子市场的二级供应链模型达到协调,使分销商的订货量达到供应链最优,并且使供应链成员的利润达到Pareto改进,达到"双赢".最后,通过算例验证了结论.展开更多
The influence of V2O3, FeO, TiO2, MnO and MgO in vanadium slag on the corrosion mechanism of MgO-C bricks was studied by stationary immersion tests at vanadium-extracting temperature. Experimental results show that Fe...The influence of V2O3, FeO, TiO2, MnO and MgO in vanadium slag on the corrosion mechanism of MgO-C bricks was studied by stationary immersion tests at vanadium-extracting temperature. Experimental results show that FeO, TiO2, and MnO could enhance the corrosion rate and V2O3 and MgO could decrease it. Microstructure and phase composition of worn samples were investigated by SEM-EDS, revealing the presence of Fe particles, produced by graphite reduction, and (Mg,Fe,Mn)O solid solution at the interface. The formation process of (Mg,Fe,Mn)O solid solution was discussed and the corrosion mechnism of MgO-C bricks was thus proposed.展开更多
Low-dimensional nanomaterials such as graphene can be used as a reinforcing agent in building materials to enhance the strength and durability. Common building materials burnt red soil bricks and fly ash bricks were r...Low-dimensional nanomaterials such as graphene can be used as a reinforcing agent in building materials to enhance the strength and durability. Common building materials burnt red soil bricks and fly ash bricks were reinforced with various amounts of graphene, and the effect of graphene on the strength of these newly developed nanocomposites was studied. The fly ash brick nanocomposite samples were cured as per their standard curing time, and the burnt red soil brick nanocomposite samples were merely dried in the sun instead of being subjected to the traditional heat treatment for days to achieve sufficient strength. The water absorption ability of the fly ash bricks was also discussed. The compressive strength of all of the graphene-reinforced nanocomposite samples was tested, along with that of some standard (without graphene) composite samples with the same dimensions, to evaluate the effects of the addition of various amounts of graphene on the compressive strength of the bricks.展开更多
Currently the service life of CDQ shafts in China is mainly restricted by the properties of the inclined flue bricks.In this work,based on the systematic analysis of the damage mechanism of inclined flue refractories,...Currently the service life of CDQ shafts in China is mainly restricted by the properties of the inclined flue bricks.In this work,based on the systematic analysis of the damage mechanism of inclined flue refractories,high performance mullite-SiC bricks were developed.The bricks were produced by corundum,andalusite,SiC and other high purity raw materials.Metal silicon and alumina ultra micropowder were added to form dispersion multi-phase structure,fortifying the matrix and improving the microstructure.The products have excellent properties such as low porosity,high density,good wear resistance,high refractoriness under load,and good thermal shock resistance.The products can replace the ordinary mullite-SiC bricks and obtain a good service life.展开更多
Serving as recycled coarse aggregate,the pretreated rural building waste was added into the concrete hollow bricks in the varying replacement of 0,20%,40%,60%,80% and 100%.By testing its compressive strength,flexural ...Serving as recycled coarse aggregate,the pretreated rural building waste was added into the concrete hollow bricks in the varying replacement of 0,20%,40%,60%,80% and 100%.By testing its compressive strength,flexural strength,mass and strength loss after freeze-thaw cycles,the impact of the different replacement on mechanical and frost-resistance properties of concrete hollow bricks was presented through SEM analysis.The experimental results show that,with the increase in recycled coarse aggregate replacement rate,the mechanical and frost-resistance properties show a downward trend;when the replacement rate is 40%,28 d compressive strength and flexural strength of concrete hollow brick demonstrate the good peak value which meet the requirement of the national standard for ordinary small concrete hollow bricks;the interfacial structures of the pretreated recycled concrete is more complicated than those of concrete made of natural aggregate,but the former enjoys better interface bonding and tight structure.展开更多
Biochar is a well-known material for pollutant removal owing to its low cost and rich surface functionality. A kind of highly active substance, called environmentally persistent free radicals(EPFRs), can be produced i...Biochar is a well-known material for pollutant removal owing to its low cost and rich surface functionality. A kind of highly active substance, called environmentally persistent free radicals(EPFRs), can be produced in the preparation process of biochar, playing an important role in the removal of pollutants.In this study, sludge-derived biochars(SBC_(120) and SBC_(270)) were prepared by the hydrothermal carbonization under two temperatures(120℃ and 270℃) to investigate their removal abilities of Cr(Ⅵ). The maximum removal amounts of Cr(Ⅵ) by SBC_(120) and SBC_(270) were 16.58 and 22.93 mg·g^(-1), respectively. It was further revealed that the appearance of Cr(Ⅲ), as a result of EPFRs on sludge-derived biochar(SBC) transferred electrons to Cr(Ⅵ) in neutral solutions. That is to say, oxygen-centered(O-centered) EPFRs on SBC_(120) and carbon-centered(C-centered) EPFRs on SBC_(270) all could be used as electron donors to Cr(Ⅵ) to make it become Cr(Ⅲ). This study not only provides a theoretical basis for the mechanism of pollutants removal by sludge-derived biochar but also offers a new perspective on the direct effect of EPFRs on pollutants.展开更多
Conversion-type fluoride cathode can provide considerable energy density for Li batteries,however its scalable and facile synthesis strategies are still lacking.Here,a novel Fe-based deep eutectic solvent composed of ...Conversion-type fluoride cathode can provide considerable energy density for Li batteries,however its scalable and facile synthesis strategies are still lacking.Here,a novel Fe-based deep eutectic solvent composed of nitrite and methylsulfonylmethane is proposed as both the reaction medium and precursor to synthesize O-doped FeF3porous bricks.This method is cheaper,safe,mildly operable,environmentally friendly and recyclable for non-fluorinated metal cations.The homogenization of charge and mass transport in cathode network effectively mitigates the volume extrusion and electrode coarsening even for the micro-sized monolithic particles.The Co-solvation modulated fluoride cathode delivers high reversible capacity in a wide temperature range(486 and 235 mA h g^(-1)at 25℃ and-20℃ respectively),excellent rate performance(312 mA h g^(-1)at 1000 mA g^(-1)),corresponding to an energy density as high as672.1 W h kg^(-1)under a power density of 2154.3 W kg^(-1).The successful operation of fluoride pouchcell with a capacity exceeding 450 mA h g^(-1)(even under thin Li foil and lean electrolyte conditions) indicates its potentiality of commercial application.展开更多
Corrosion effect of ladle furnace （LF） refining slag on fired MgO-CaO bricks with about 34% CaO was studied by static crucible method,and corrosion mechanism was analyzed by techniques of scan electron micrograph,en...Corrosion effect of ladle furnace （LF） refining slag on fired MgO-CaO bricks with about 34% CaO was studied by static crucible method,and corrosion mechanism was analyzed by techniques of scan electron micrograph,energy dispersive spectrometer,and X-ray diffraction. The results show that：MgO-CaO bricks exhibit excellent corrosion resistance but poor penetration resistance to LF refining slag; oxidation of （Mg·Fe）O in reaction zone results in volume expansion forming cracks; penetration of 2CaO·Fe2O3 （C2F） from slag to MgO-CaO bricks increases liquid phases which accelerates corrosion of the bricks; a protective layer of 2CaO·SiO2 formed on reaction interface prevents penetration of C2F to the bricks.展开更多
In order to utilize solid wastes,ceramic simple bricks with high performances were made from industrial solid wastes such as red mud,fly ash and poor clay shale as main raw materials in this paper.The phase compositio...In order to utilize solid wastes,ceramic simple bricks with high performances were made from industrial solid wastes such as red mud,fly ash and poor clay shale as main raw materials in this paper.The phase compositions and microstructures were tested by XRD,SEM and EPMA.The experimental results show that the water absorption is 45.64%,the porosity is 58.91%,bulk density is 1.29 g·cm-3,compressive strength is 54.91 MPa,bending strength is 29.52 MPa,freeze-thaw resistance is 29.28 MPa,specific heat capacity at constant pressure is 1.31 J·g-1·K-1,thermal diffusivity is 5.89×10-3 cm2·s-1,and thermal conductivity is 1.15×10-2 W·cm-1·K-1.These effects of additives and preparation process to the properties and microstructures were discussed in detail.The reaction mechanism was also discussed.The results of the reaction mechanism show that there has wollastonite and feldspar generated during the process of firing while Ca gathered around the feldspar,and then Ca would displace K and generated cacoclasite.展开更多
The annual output of China ' s silica brick amounts up to over 300 thousand tons, which accounts for more than 10% of the total output of silica bricks in the world. Besides satisfying domestic markets , China s s...The annual output of China ' s silica brick amounts up to over 300 thousand tons, which accounts for more than 10% of the total output of silica bricks in the world. Besides satisfying domestic markets , China s silica bricks have been exported to many countries and regions such as Japan, USA etc. In this paper, the situation of silica bricks production, technology, sales and exporting have been described. Also suggestions on improvement of silica bricks quality and exporting, corporation with foreign partners have been put forward in order to win larger market share both at home and abroad.展开更多
Pitch and tar bonded dolomite bricks are extensively used in ladles and converters for long time because of their superior properties such as. steel melt refining, easy production as well as low production cost. Recen...Pitch and tar bonded dolomite bricks are extensively used in ladles and converters for long time because of their superior properties such as. steel melt refining, easy production as well as low production cost. Recently, resin bonded dolomite bricks are presented for using in steel plants. Generally, quality and final cost of steels are affected by properties of refractories especially dolomite bricks. Therefore, recognition of influence parameters on dolomite refractory properties is very important. In this study, the effects of tar and resin as bonding systems, and addition of graphite （ 2wt% ） on the properties of dolomite refractory bricks have been investigated. Properties such as ： density and porosity, cold crushing strength, hydration time and depth of slag penetration have been studied. Results show that the bonding sys- tems and graphite have a great effect on the mentioned properties especially cold crushing strength and hydra- tion time. In addition to their low rate of pollution, resin bonded dolomite bricks show higher performance with proper technical specifications.展开更多
The high chrome bricks specimens were prepared by firing at 1 350,1 450 and 1 550 ℃ in carbon embedded condition and at 1 700 ℃ in air,respectively. Effects of firing atmospheres （carbon embedded and air） on bulk ...The high chrome bricks specimens were prepared by firing at 1 350,1 450 and 1 550 ℃ in carbon embedded condition and at 1 700 ℃ in air,respectively. Effects of firing atmospheres （carbon embedded and air） on bulk density,apparent porosity,cold crushing strength,and slag penetration resistance of high chrome bricks were researched in order to improve physical properties and corrosion resistance of high chrome bricks and to prolong the service life in slagging coal gasifier. The results show that with temperature rising,the apparent porosity of specimens decreases and the bulk density increases; the cold crushing strength of the specimens carbon embedded fired at 1 450 ℃ is the highest,reaching 214 MPa; carbon embedded condition is beneficial to reducing the sintering temperature and improving the microstructure; the specimens carbon embedded fired at 1 450 ℃ perform better slag penetration resistance than the specimens fired at 1 700 ℃ in air.展开更多
The use of the thermal power plant ashes including fly ash(FA) and bottom ash(BA) for producing unfired building bricks(UBB) using sodium hydroxide(NaOH) solution as an alkaline activator was investigated. A low appli...The use of the thermal power plant ashes including fly ash(FA) and bottom ash(BA) for producing unfired building bricks(UBB) using sodium hydroxide(NaOH) solution as an alkaline activator was investigated. A low applied forming pressure of 0.5 MPa and various NaOH concentrations of 5, 8, 10, and 12 M were used for the preparation of brick samples with different solution-to-binder(S/B) ratios of 0.35 and 0.40. The bricks were subjected to various test programs with reflecting the effect of both NaOH concentrations and S/B ratios on the brick’s properties. The compressive strength, unit weight, ultrasonic pulse velocity, and thermal conductivity of bricks increased with increasing NaOH concentration, whereas the contrary trend was found with increasing S/B ratio. Also, the water absorption of bricks was observed to reduce with increasing NaOH concentration and decreasing S/B ratio. As the results, the combined utilization of both low forming pressure and coal power plant ashes can produce the UBBs with low unit weight, low heat conductivity, and acceptable strength and water absorption rate as stipulated by TCVN 6477-2016. Furthermore, the outcomes of chemical analysis and microstructure observation also demonstrate that a high concentration of the Na OH promoted the geopolymerization process. Notably, the use of NaOH solution of either 10 M or above is recommended for the production of UBBs, which are classified as grade M5.0 or higher.展开更多
Dense corundum-mullite brick for blast furnace ceramic pad was prepared using white fused corundum and tabular corundum as aggregates,andalusite fine powder,sillimanite fine powder,zircon sand powder and Guangxi soil ...Dense corundum-mullite brick for blast furnace ceramic pad was prepared using white fused corundum and tabular corundum as aggregates,andalusite fine powder,sillimanite fine powder,zircon sand powder and Guangxi soil as the matrix,and phosphate as the binder,introducing different amounts ofα-alumina micropowder,tabular corundum fine powder and fused corundum powder.The properties of the prepared brick were studied.The results show that,the brick with 10 mass%of tabular corundum fine powder fired at 1560℃for 3 h in a tunnel kiln has the bulk density of 3.08 g·cm^(-3),the apparent porosity of 13.2%,the cold compressive strength of 178 MPa,the molten iron corrosion rate of 0.6%,the slag corrosion rate of 6.4%,the alkali resistance strength decreasing rate of 7.5%,and the thermal shock resistance of 32 cycles,which is both dense and of good thermal shock resistance.The slag resistance simulation test was performed,which proved that the prepared corundum-mullite brick is better than those currently supplied in the market.展开更多
The microstructure of high chrome bricks made at different sintering temperature are analyzed by SEM . The results indicate that the sintering temperature of high chromebricks has an optimum range , it is not the high...The microstructure of high chrome bricks made at different sintering temperature are analyzed by SEM . The results indicate that the sintering temperature of high chromebricks has an optimum range , it is not the higher, the better, The high chrome bricks made at this -sintering temperature have the moderate crystal six in the matrix and of dense structure. The closed bonding structure could be obtained between grains and matrix and no crackle occurred.The high chrome bricks with this microstructure have the best dynamic properties.展开更多
MgO -ZrO2 unfired bricks with ZrO2 content up to 8% at the interval of 2% were prepared, using fused magnesia （ MgO ： 97% ） and fused MgO - ZrO2 clinker （ ZrO2 ： 14. 33% ） as starting materials and phenolic resi...MgO -ZrO2 unfired bricks with ZrO2 content up to 8% at the interval of 2% were prepared, using fused magnesia （ MgO ： 97% ） and fused MgO - ZrO2 clinker （ ZrO2 ： 14. 33% ） as starting materials and phenolic resin as binder. The effects of ZrO2 content on thermal shock resistance （TSR） and other properties such as cold and hot modulus of rupture have been investigated. Re- sidual cold modulus of rupture ratio after heating at 1 000 ℃ and quenching by air blowing was adopted to characterize TSR. Addition of the MgO -ZrO2 clinker improves TSR, attributing to the microcrack toughening effect by thermal expansion mismatch between different phases. When ZrO2 content goes above 4%. the impro- ving effect tends to be moderate. The introduction of MgO- ZrO2 clinker can also improve the HMOR at 1 500 ℃, while the increased ZrO2 content reduces CMOR of the bricks prefired at 1 600 ℃, due to the thermal expansion mismatch effect. Compromising the overall properties, the optimal ZrO2 content for such magnesia based unfired brick is suggested to be 4%.展开更多
文摘The aim of this study is to enhance the value of local earth materials used in the construction of certain homes in the Republic of Guinea. Thus, a trial study to improve the quality of mud bricks using paper fibers obtained by grinding and soaking in water and then drying were used as a stabilizer in the manufacture of these mud bricks from the sample of two sites Dounkiwal (DK) (in Mamou and the sample from the urban commune of Kouroussa). To do this, certain methods and means of identification were carried out, namely: geotechnical, mineralogical and chemical analyses. Sample DK from Mamou has a silty-clay geotechnical characteristic with a plasticity index Ip of 12.75%. However, mineralogical and chemical studies showed that sample Dounkiwal (DK) (Mamou) contains a high proportion of silica and iron oxides (79.63%) and Fe2O3 (11.85%), associated with other alkaline earth oxides and ions: CaO;MgO;SO32−;Cl−, i.e. 3.96%;0.96%;0.28% and 0.039% respectively. Its loss on ignition (LOI) and insoluble residues are 15.40% and 56.36%. The evaluation of the number of huts in Upper and Middle Guinea showed that the populations of these areas have been using mud bricks for several decades in the construction of dwellings. The average value found for the compressive strength of these bricks (from samples I, II and III from Kouroussa) is 0.16 MPa. This value is appreciable in the construction of mud houses.
文摘This study was part of the framework that contributed not only to the improvement of thermal comfort in housing but also to the decarbonization of the construction and building materials industry. For this purpose, terracotta brick seems to meet these needs. Thus, the objective of this work was to evaluate the influence of the incorporation of coal fly ash from a thermal power plant on the physical and mechanical properties of fired bricks from grey clay in the Thicky area of Senegal. The coal fly ash was incorporated into the raw clay material in proportions of 0, 5, 10, and 15 % by weight. These two raw materials were first characterized by X-ray fluorescence spectroscopy (XRF). The XRF analyses showed that the most abundant oxides in clay were SiO2 (55.034%) and Fe2O3 (10.155%). In coal fly ash, SiO2 (38.574%) is predominant. The ash also contained Al2O3 (7.717%) and alicano-earthy melting oxides such as CaO (9.271%) and MgO (7.298%) etc. These melting oxides were necessary to facilitate the formation of the liquid phase when baking platelets. The latter, when burned at a temperature of 880°C, were characterized by determining the number of physico-mechanical parameters, such as linear shrinkage during cooking, water absorption, fire loss and compressive strength. A Hierarchical Ascending Classification of these different parameters was performed and three classes were obtained. Class 1 with better compressive strength (6.358 MPa), was in sample A (5%). Class 2 consisted of sample D (reference) and had a higher plasticity index (28.51%) and water absorption rate (11.19%). Finally, class 3, which included samples B (10%) and C (15%), had very high shrinkage and fire losses compared to other platelets. These results highlighted the possibility of using up to 5% of the coal fly ash in the production of new fired bricks with good performance.
文摘建立了由一个制造商和一个分销商组成的基于电子市场的二级供应链模型,讨论了分销商采用Bricks and Clicks模式分销产品,并在电子渠道进行季节后销售的情况,分析了供应链的契约协调问题及供应链成员的利润情况.研究发现改进的回购契约可以使Bricks and Clicks分销模式下基于电子市场的二级供应链模型达到协调,使分销商的订货量达到供应链最优,并且使供应链成员的利润达到Pareto改进,达到"双赢".最后,通过算例验证了结论.
基金Item Sponsored by National Natural Science Foundation of China (51090382)
文摘The influence of V2O3, FeO, TiO2, MnO and MgO in vanadium slag on the corrosion mechanism of MgO-C bricks was studied by stationary immersion tests at vanadium-extracting temperature. Experimental results show that FeO, TiO2, and MnO could enhance the corrosion rate and V2O3 and MgO could decrease it. Microstructure and phase composition of worn samples were investigated by SEM-EDS, revealing the presence of Fe particles, produced by graphite reduction, and (Mg,Fe,Mn)O solid solution at the interface. The formation process of (Mg,Fe,Mn)O solid solution was discussed and the corrosion mechnism of MgO-C bricks was thus proposed.
文摘Low-dimensional nanomaterials such as graphene can be used as a reinforcing agent in building materials to enhance the strength and durability. Common building materials burnt red soil bricks and fly ash bricks were reinforced with various amounts of graphene, and the effect of graphene on the strength of these newly developed nanocomposites was studied. The fly ash brick nanocomposite samples were cured as per their standard curing time, and the burnt red soil brick nanocomposite samples were merely dried in the sun instead of being subjected to the traditional heat treatment for days to achieve sufficient strength. The water absorption ability of the fly ash bricks was also discussed. The compressive strength of all of the graphene-reinforced nanocomposite samples was tested, along with that of some standard (without graphene) composite samples with the same dimensions, to evaluate the effects of the addition of various amounts of graphene on the compressive strength of the bricks.
文摘Currently the service life of CDQ shafts in China is mainly restricted by the properties of the inclined flue bricks.In this work,based on the systematic analysis of the damage mechanism of inclined flue refractories,high performance mullite-SiC bricks were developed.The bricks were produced by corundum,andalusite,SiC and other high purity raw materials.Metal silicon and alumina ultra micropowder were added to form dispersion multi-phase structure,fortifying the matrix and improving the microstructure.The products have excellent properties such as low porosity,high density,good wear resistance,high refractoriness under load,and good thermal shock resistance.The products can replace the ordinary mullite-SiC bricks and obtain a good service life.
基金Funded by the National Key Technology R&D Program of China for the 11th Five-Year Plan(2006BAJ04A04)the 100 Million Human Resources Foundation of Liaoning Province (2008921034)the Human Resource Development in Shenyang Special Foundation (2008140403011)
文摘Serving as recycled coarse aggregate,the pretreated rural building waste was added into the concrete hollow bricks in the varying replacement of 0,20%,40%,60%,80% and 100%.By testing its compressive strength,flexural strength,mass and strength loss after freeze-thaw cycles,the impact of the different replacement on mechanical and frost-resistance properties of concrete hollow bricks was presented through SEM analysis.The experimental results show that,with the increase in recycled coarse aggregate replacement rate,the mechanical and frost-resistance properties show a downward trend;when the replacement rate is 40%,28 d compressive strength and flexural strength of concrete hollow brick demonstrate the good peak value which meet the requirement of the national standard for ordinary small concrete hollow bricks;the interfacial structures of the pretreated recycled concrete is more complicated than those of concrete made of natural aggregate,but the former enjoys better interface bonding and tight structure.
基金supported by the Beijing Municipal Natural Science Foundation (8202007)the National Natural Science Foundation of China (52170148)。
文摘Biochar is a well-known material for pollutant removal owing to its low cost and rich surface functionality. A kind of highly active substance, called environmentally persistent free radicals(EPFRs), can be produced in the preparation process of biochar, playing an important role in the removal of pollutants.In this study, sludge-derived biochars(SBC_(120) and SBC_(270)) were prepared by the hydrothermal carbonization under two temperatures(120℃ and 270℃) to investigate their removal abilities of Cr(Ⅵ). The maximum removal amounts of Cr(Ⅵ) by SBC_(120) and SBC_(270) were 16.58 and 22.93 mg·g^(-1), respectively. It was further revealed that the appearance of Cr(Ⅲ), as a result of EPFRs on sludge-derived biochar(SBC) transferred electrons to Cr(Ⅵ) in neutral solutions. That is to say, oxygen-centered(O-centered) EPFRs on SBC_(120) and carbon-centered(C-centered) EPFRs on SBC_(270) all could be used as electron donors to Cr(Ⅵ) to make it become Cr(Ⅲ). This study not only provides a theoretical basis for the mechanism of pollutants removal by sludge-derived biochar but also offers a new perspective on the direct effect of EPFRs on pollutants.
基金supported by the National Natural Science Foundation of China(51772313,21975276 and 52102329)the Shanghai Science and Technology Committee(20520710800)support by the Program of Shanghai Academic Research Leader(21XD1424400)。
文摘Conversion-type fluoride cathode can provide considerable energy density for Li batteries,however its scalable and facile synthesis strategies are still lacking.Here,a novel Fe-based deep eutectic solvent composed of nitrite and methylsulfonylmethane is proposed as both the reaction medium and precursor to synthesize O-doped FeF3porous bricks.This method is cheaper,safe,mildly operable,environmentally friendly and recyclable for non-fluorinated metal cations.The homogenization of charge and mass transport in cathode network effectively mitigates the volume extrusion and electrode coarsening even for the micro-sized monolithic particles.The Co-solvation modulated fluoride cathode delivers high reversible capacity in a wide temperature range(486 and 235 mA h g^(-1)at 25℃ and-20℃ respectively),excellent rate performance(312 mA h g^(-1)at 1000 mA g^(-1)),corresponding to an energy density as high as672.1 W h kg^(-1)under a power density of 2154.3 W kg^(-1).The successful operation of fluoride pouchcell with a capacity exceeding 450 mA h g^(-1)(even under thin Li foil and lean electrolyte conditions) indicates its potentiality of commercial application.
文摘Corrosion effect of ladle furnace （LF） refining slag on fired MgO-CaO bricks with about 34% CaO was studied by static crucible method,and corrosion mechanism was analyzed by techniques of scan electron micrograph,energy dispersive spectrometer,and X-ray diffraction. The results show that：MgO-CaO bricks exhibit excellent corrosion resistance but poor penetration resistance to LF refining slag; oxidation of （Mg·Fe）O in reaction zone results in volume expansion forming cracks; penetration of 2CaO·Fe2O3 （C2F） from slag to MgO-CaO bricks increases liquid phases which accelerates corrosion of the bricks; a protective layer of 2CaO·SiO2 formed on reaction interface prevents penetration of C2F to the bricks.
基金Funded by the 11th Five-Year National Key Technology R&D Program(2008BAC41B00)
文摘In order to utilize solid wastes,ceramic simple bricks with high performances were made from industrial solid wastes such as red mud,fly ash and poor clay shale as main raw materials in this paper.The phase compositions and microstructures were tested by XRD,SEM and EPMA.The experimental results show that the water absorption is 45.64%,the porosity is 58.91%,bulk density is 1.29 g·cm-3,compressive strength is 54.91 MPa,bending strength is 29.52 MPa,freeze-thaw resistance is 29.28 MPa,specific heat capacity at constant pressure is 1.31 J·g-1·K-1,thermal diffusivity is 5.89×10-3 cm2·s-1,and thermal conductivity is 1.15×10-2 W·cm-1·K-1.These effects of additives and preparation process to the properties and microstructures were discussed in detail.The reaction mechanism was also discussed.The results of the reaction mechanism show that there has wollastonite and feldspar generated during the process of firing while Ca gathered around the feldspar,and then Ca would displace K and generated cacoclasite.
文摘The annual output of China ' s silica brick amounts up to over 300 thousand tons, which accounts for more than 10% of the total output of silica bricks in the world. Besides satisfying domestic markets , China s silica bricks have been exported to many countries and regions such as Japan, USA etc. In this paper, the situation of silica bricks production, technology, sales and exporting have been described. Also suggestions on improvement of silica bricks quality and exporting, corporation with foreign partners have been put forward in order to win larger market share both at home and abroad.
文摘Pitch and tar bonded dolomite bricks are extensively used in ladles and converters for long time because of their superior properties such as. steel melt refining, easy production as well as low production cost. Recently, resin bonded dolomite bricks are presented for using in steel plants. Generally, quality and final cost of steels are affected by properties of refractories especially dolomite bricks. Therefore, recognition of influence parameters on dolomite refractory properties is very important. In this study, the effects of tar and resin as bonding systems, and addition of graphite （ 2wt% ） on the properties of dolomite refractory bricks have been investigated. Properties such as ： density and porosity, cold crushing strength, hydration time and depth of slag penetration have been studied. Results show that the bonding sys- tems and graphite have a great effect on the mentioned properties especially cold crushing strength and hydra- tion time. In addition to their low rate of pollution, resin bonded dolomite bricks show higher performance with proper technical specifications.
文摘The high chrome bricks specimens were prepared by firing at 1 350,1 450 and 1 550 ℃ in carbon embedded condition and at 1 700 ℃ in air,respectively. Effects of firing atmospheres （carbon embedded and air） on bulk density,apparent porosity,cold crushing strength,and slag penetration resistance of high chrome bricks were researched in order to improve physical properties and corrosion resistance of high chrome bricks and to prolong the service life in slagging coal gasifier. The results show that with temperature rising,the apparent porosity of specimens decreases and the bulk density increases; the cold crushing strength of the specimens carbon embedded fired at 1 450 ℃ is the highest,reaching 214 MPa; carbon embedded condition is beneficial to reducing the sintering temperature and improving the microstructure; the specimens carbon embedded fired at 1 450 ℃ perform better slag penetration resistance than the specimens fired at 1 700 ℃ in air.
文摘The use of the thermal power plant ashes including fly ash(FA) and bottom ash(BA) for producing unfired building bricks(UBB) using sodium hydroxide(NaOH) solution as an alkaline activator was investigated. A low applied forming pressure of 0.5 MPa and various NaOH concentrations of 5, 8, 10, and 12 M were used for the preparation of brick samples with different solution-to-binder(S/B) ratios of 0.35 and 0.40. The bricks were subjected to various test programs with reflecting the effect of both NaOH concentrations and S/B ratios on the brick’s properties. The compressive strength, unit weight, ultrasonic pulse velocity, and thermal conductivity of bricks increased with increasing NaOH concentration, whereas the contrary trend was found with increasing S/B ratio. Also, the water absorption of bricks was observed to reduce with increasing NaOH concentration and decreasing S/B ratio. As the results, the combined utilization of both low forming pressure and coal power plant ashes can produce the UBBs with low unit weight, low heat conductivity, and acceptable strength and water absorption rate as stipulated by TCVN 6477-2016. Furthermore, the outcomes of chemical analysis and microstructure observation also demonstrate that a high concentration of the Na OH promoted the geopolymerization process. Notably, the use of NaOH solution of either 10 M or above is recommended for the production of UBBs, which are classified as grade M5.0 or higher.
文摘Dense corundum-mullite brick for blast furnace ceramic pad was prepared using white fused corundum and tabular corundum as aggregates,andalusite fine powder,sillimanite fine powder,zircon sand powder and Guangxi soil as the matrix,and phosphate as the binder,introducing different amounts ofα-alumina micropowder,tabular corundum fine powder and fused corundum powder.The properties of the prepared brick were studied.The results show that,the brick with 10 mass%of tabular corundum fine powder fired at 1560℃for 3 h in a tunnel kiln has the bulk density of 3.08 g·cm^(-3),the apparent porosity of 13.2%,the cold compressive strength of 178 MPa,the molten iron corrosion rate of 0.6%,the slag corrosion rate of 6.4%,the alkali resistance strength decreasing rate of 7.5%,and the thermal shock resistance of 32 cycles,which is both dense and of good thermal shock resistance.The slag resistance simulation test was performed,which proved that the prepared corundum-mullite brick is better than those currently supplied in the market.
文摘The microstructure of high chrome bricks made at different sintering temperature are analyzed by SEM . The results indicate that the sintering temperature of high chromebricks has an optimum range , it is not the higher, the better, The high chrome bricks made at this -sintering temperature have the moderate crystal six in the matrix and of dense structure. The closed bonding structure could be obtained between grains and matrix and no crackle occurred.The high chrome bricks with this microstructure have the best dynamic properties.
文摘MgO -ZrO2 unfired bricks with ZrO2 content up to 8% at the interval of 2% were prepared, using fused magnesia （ MgO ： 97% ） and fused MgO - ZrO2 clinker （ ZrO2 ： 14. 33% ） as starting materials and phenolic resin as binder. The effects of ZrO2 content on thermal shock resistance （TSR） and other properties such as cold and hot modulus of rupture have been investigated. Re- sidual cold modulus of rupture ratio after heating at 1 000 ℃ and quenching by air blowing was adopted to characterize TSR. Addition of the MgO -ZrO2 clinker improves TSR, attributing to the microcrack toughening effect by thermal expansion mismatch between different phases. When ZrO2 content goes above 4%. the impro- ving effect tends to be moderate. The introduction of MgO- ZrO2 clinker can also improve the HMOR at 1 500 ℃, while the increased ZrO2 content reduces CMOR of the bricks prefired at 1 600 ℃, due to the thermal expansion mismatch effect. Compromising the overall properties, the optimal ZrO2 content for such magnesia based unfired brick is suggested to be 4%.
