In recent years,an increase in the content of Zn,the impurity element,in ironmaking raw materials has led to the deterioration of iron-bearing resources and has introduced new challenges to sintering dezincification.A...In recent years,an increase in the content of Zn,the impurity element,in ironmaking raw materials has led to the deterioration of iron-bearing resources and has introduced new challenges to sintering dezincification.A thorough understanding of the reaction behavior of Zn during the sintering process can form a theoretical foundation for the development of efficient dezincification technology.Therefore,the reaction behavior of Zn was investigated under different temperatures and atmospheres using thermodynamic calculations and experimental simulations,and the phase transformation of Zn in each pre-reductive sintering zone was investigated.The results showed that Zn-containing materials were mainly converted into ZnO when the temperature reached 700℃,and ZnO began to combine with Fe_(2)O_(3)to form ZnFe_(2)O_(4)at approximately 800℃.At low CO concentration,ZnFe_(2)O_(4)was stable,while ZnO combined with iron oxide to form Fe_(0.85-x)Zn_(x)O in a strong reduction atmosphere.ZnFe_(2)O_(4)could also be converted into Fe_(0.85-x)Zn_(x)O and FeO.A part of Zn was converted to elemental Zn,which was volatilized and removed into the gas phase above 1000℃.Therefore,the feasibility of dezincification via pre-reductive sintering was confirmed.At the coke ratio of 18.0 wt.%of the sintering material,the Zn removal rate reached 62.3 wt.%.展开更多
The cold sintering process(CSP)is a green and innovative method of material densification at low temperatures(<350°C).The traditional CSP entails the addition of liquid phases as a solvent to achieve material ...The cold sintering process(CSP)is a green and innovative method of material densification at low temperatures(<350°C).The traditional CSP entails the addition of liquid phases as a solvent to achieve material densification through the dissolution-precipitation mechanism.However,it is difficult to realize for materials with low solubility.To address this challenge,a universal cold sintering method without the addition of liquid phases has been proposed in this work.The addition of a special polyester-polymer assisted the densification of insoluble ceramics,and hydroxyapatite(HA)and Al_(2)O_(3)were successfully sintered below 100°C,achieving 95-100%densities in a short time(5-20 min).This achievement can be attributed to the low glass transition temperature and the abundance of active sites(C=O)of the polyester-polymer.The denser ceramics exhibited enhanced mechanical properties,with the compression strength of polymer-assisted CSP HA increasing by 147.3%compared to the nanoparticles.Additionally,serving as an advanced bone substitute material,HA underwent quantitative analysis using the CCK-8 method and assessed the impact of polymer presence on cell proliferation and cytotoxicity.Meanwhile,a tight bonding between the polymer and ceramic materials was achieved during CSP,providing a generalized method for designing multifunctional ceramic-polymer.展开更多
Iron and steel industry is one of the main sources of air pollution emissions in China.The sintering process is an important link in the blast furnace ironmaking process,but it is also accompanied by a large number of...Iron and steel industry is one of the main sources of air pollution emissions in China.The sintering process is an important link in the blast furnace ironmaking process,but it is also accompanied by a large number of pollutants.Under the background of ultra-low emissions,iron and steel enterprises urgently need to upgrade their existing processes to address the existing process in practical application problems.In this study,a steel group in Gansu Province was taken as an example.By comparing and analyzing the pollutant emission characteristics before and after the ultra-low emission retrofit,the collaborative control effect of the combined process on SO_(2),NO_(x),particulate matter,and dioxins after the new retrofit was systematically evaluated.The results show that after the retrofit,the concentrations of particulate matter,SO_(2) and NO_(x) have dropped to near-zero levels,and the dioxin removal efficiency has reached 98.87%,with all indicators being better than the national ultra-low emission standards.The study confirms that the optimal combination of multi-pollutant collaborative treatment technologies is the key to achieving efficient emission reduction,among which selective catalytic reduction technology has a particularly significant synergistic removal effect on NO_(x) and dioxins.This study provides an important technical reference and practical basis for the ultra-low emission retrofit of the steel industry,and has important guiding significance for promoting the green retrofit of the industry.Its ultra-low emission retrofit is of great significance for achieving green and low-carbon development.展开更多
The use of high entropy alloy as a binder for tungsten heavy alloys offers potential advantages.The 95W-5CoCrFeMnNi alloys(95W-HEAs)were prepared via powder metallurgy at sintering temperatures of 1400−1550℃.The micr...The use of high entropy alloy as a binder for tungsten heavy alloys offers potential advantages.The 95W-5CoCrFeMnNi alloys(95W-HEAs)were prepared via powder metallurgy at sintering temperatures of 1400−1550℃.The microstructure analysis revealed that the tungsten phase in 95W-HEAs exhibited a nearly spherical morphology in the HEA binder matrix and the formation of a Cr−Mn oxide mixed phase was observed.The sintering temperature exerted a significant influence on the relative density,grain size,W−W contiguity,and mechanical properties of the alloys.The optimal performance was achieved when sintering at 1450℃,yielding a relative density of 96.61%,a W−W contiguity of 0.528,an average grain size of 18.97μm,a compressive strength of 2234.82 MPa,and a hardness of HV 400.6.The activation energy for the diffusion of tungsten in the liquid phase formed by HEA binder was calculated to be 354.514 kJ/mol,highlighting its role in controlling grain growth.展开更多
This study investigated enhancing the wear resistance of Ti6Al4V alloys for medical applications by incorporating Ti C nanoreinforcements using advanced spark plasma sintering(SPS). The addition of up to 2.5wt% Ti C s...This study investigated enhancing the wear resistance of Ti6Al4V alloys for medical applications by incorporating Ti C nanoreinforcements using advanced spark plasma sintering(SPS). The addition of up to 2.5wt% Ti C significantly improved the mechanical properties, including a notable 18.2% increase in hardness(HV 332). Fretting wear tests against 316L stainless steel(SS316L) balls demonstrated a 20wt%–22wt% reduction in wear volume in the Ti6Al4V/Ti C composites compared with the monolithic alloy. Microstructural analysis revealed that Ti C reinforcement controlled the grain orientation and reduced the β-phase content, which contributed to enhanced mechanical properties. The monolithic alloy exhibited a Widmanstätten lamellar microstructure, while increasing the Ti C content modified the wear mechanisms from ploughing and adhesion(0–0.5wt%) to pitting and abrasion(1wt%–2.5wt%). At higher reinforcement levels, the formation of a robust oxide layer through tribo-oxide treatment effectively reduced the wear volume by minimizing the abrasive effects and plastic deformation. This study highlights the potential of SPS-mediated Ti C reinforcement as a transformative approach for improving the performance of Ti6Al4V alloys, paving the way for advanced medical applications.展开更多
Coke oven gas(COG)and natural gas(NG),both high-calorific by-products derived from the steel industry,have gained prominence as alternative fuels in the sintering process,thereby supporting dual objectives of emission...Coke oven gas(COG)and natural gas(NG),both high-calorific by-products derived from the steel industry,have gained prominence as alternative fuels in the sintering process,thereby supporting dual objectives of emission reduction and carbon neutrality.While existing research on hydrogen-rich gas injection has predominantly concentrated on conventional thin-bed sintering,investigations into its application within thick-bed sintering remain comparatively scarce.Thick-bed sintering,recognized for enhancing energy efficiency and increasing sinter output,encounters challenges such as uneven heat distribution and diminished permeability,which can negatively impact process efficiency and product quality.To address these issues,sinter pot experiments were conducted to assess the effects of NG and COG injection on thick-bed sintering performance.Findings reveal that NG injection in thick beds mirrors the behavior observed in conventional thin-bed sintering,effectively optimizing the process and achieving a carbon reduction potential exceeding 10%.In contrast,COG injection in thick-bed conditions demonstrates notable differences,substantially lowering the solid fuel consumption rate but detrimentally affecting sinter strength and overall production.However,by optimizing the timing of COG injection,it is feasible to improve sinter yield while concurrently reducing solid fuel usage.These outcomes provide valuable insights for the advancement of gas injection technologies in thick-bed sintering,thereby contributing to energy conservation and emission mitigation efforts within the sintering industry.展开更多
Sinter is the core raw material for blast furnaces.Flue pressure,which is an important state parameter,affects sinter quality.In this paper,flue pressure prediction and optimization were studied based on the shapley a...Sinter is the core raw material for blast furnaces.Flue pressure,which is an important state parameter,affects sinter quality.In this paper,flue pressure prediction and optimization were studied based on the shapley additive explanation(SHAP)to predict the flue pressure and take targeted adjustment measures.First,the sintering process data were collected and processed.A flue pressure prediction model was then constructed after comparing different feature selection methods and model algorithms using SHAP+extremely random-ized trees(ET).The prediction accuracy of the model within the error range of±0.25 kPa was 92.63%.SHAP analysis was employed to improve the interpretability of the prediction model.The effects of various sintering operation parameters on flue pressure,the relation-ship between the numerical range of key operation parameters and flue pressure,the effect of operation parameter combinations on flue pressure,and the prediction process of the flue pressure prediction model on a single sample were analyzed.A flue pressure optimization module was also constructed and analyzed when the prediction satisfied the judgment conditions.The operating parameter combination was then pushed.The flue pressure was increased by 5.87%during the verification process,achieving a good optimization effect.展开更多
Comprehensive two-dimensional gas chromatography coupled with time-of-flight mass spectrometry （ GC x GC- TOFMS） was applied to the quick qualitative analysis of 17 types of polychlorinated dibenzo-p-dioxins and fur...Comprehensive two-dimensional gas chromatography coupled with time-of-flight mass spectrometry （ GC x GC- TOFMS） was applied to the quick qualitative analysis of 17 types of polychlorinated dibenzo-p-dioxins and furans （PCDD/Fs） from the iron ore sintering process. The GC x GC-TOFMS parameters were evaluated and optimized to yield a complete separation for the 17 types of PCCD/Fs from interference and to the attainment of high sensitivity. After optimization, all the 17 types of PCCD/Fs were separated within 42.5 min. The critical and most toxic tetrachlorodibenzo- p-dioxin （TCDD） detection can be up to 0.5 ~g/L. The method was used to analyze real fly ash samples. Accurate identification and determination of all the analyses were by GC x GC, mass spectrum library and ion ratio. The technique is thought to be a substitute for and a supplement to high resolution gas chromatography/high resolution mass spectrometry （HRGC/HRMS） in the field of dioxin analysis.展开更多
A pre-reduction sintering process with flue gas recirculation(PSP_(fsg)-FGR)was developed to mitigate alkalis harm to the blast furnace and reduce the flue gas emission in the whole ironmaking process.The results indi...A pre-reduction sintering process with flue gas recirculation(PSP_(fsg)-FGR)was developed to mitigate alkalis harm to the blast furnace and reduce the flue gas emission in the whole ironmaking process.The results indicated that the pre-reduction sintering process(PSP)can effectively remove 58.02%of K and 30.68%of Na from raw mixtures and improve yield and tumbler index to 74.40%and 68.69%,respectively.Moreover,PSP was conducive to reducing NO_(x) and SO_(2)emissions and simultaneously increasing CO content in flue gas.Circulating CO-containing flue gas to sintering bed effectively recycled CO and further improved K and Na removal ratio to 74.11%and 32.92%,respectively.Microstructural analysis revealed that the pre-reduced sinter mainly consisted of magnetite,wustite and a small quantity of metallic iron,and very few silicate glass phase was also formed.This process can simultaneously realize alkali metal elements removal as well as flue gas emission reduction from the integrated ironmaking process.展开更多
As the bed depth increases,sintering yield increases,but the productivity decreases.To reveal the reasons for the decrease in productivity and explore targeted solutions,the bed resistance of mixtures,wet zone,and com...As the bed depth increases,sintering yield increases,but the productivity decreases.To reveal the reasons for the decrease in productivity and explore targeted solutions,the bed resistance of mixtures,wet zone,and combustion zone was analyzed in the laboratory.The results showed that the decreased porosity of mixture resulted in the increased bed resistance by 160.56%when the bed depth increased from 600 to 1000 mm.After improving porosity of 1%by adding loosening bars with optimized size and distribution,the bed resistance decreased,and the productivity increased by 5%.The increase in bed depth increased the thickness of the wet zone from 120 to 680 mm and the resistance from 1.56 to 8.83 kPa.By using a three-stage intensive mixer and pre-adding water for granulation,the moisture of mixture was reduced by 0.6%,and the sintering productivity increased by 4%.Besides,the high bed resistance is mainly caused by the increase in the thickness of the combustion zone from 31.9 to 132.7 mm,and the bed resistance increased from 0.70 to 5.62 kPa.The bed resistance of the combustion zone at 900 mm was increased by 90.51%compared to 700 mm.After optimization of the distribution of coke breeze,the thickness of combustion zone at the lower layer decreased from 132.7 to 106.84 mm and permeability improved significantly.展开更多
The challenge of low temperature and rapid diffusion bonding of a Ni-based superalloy was hereby addressed by using a Ni nano-coating and a spark plasma sintering(SPS).It successfully produced a Nibased superalloy joi...The challenge of low temperature and rapid diffusion bonding of a Ni-based superalloy was hereby addressed by using a Ni nano-coating and a spark plasma sintering(SPS).It successfully produced a Nibased superalloy joint with 337 MPa shear strength at 500℃ for 30 min,which is approximately 400℃ lower than the traditional hot pressure diffusion bonding(HPDB)temperature.The microstructure and mechanical properties of the joints were systematically investigated.It is revealed that the pulsed current and ultra-fine grains(19 nm)in the Ni nano-coating could significantly facilitate voids closure.The voids closure mechanisms involved(i)pulsed current strengthened plastic deformation,(ii)pulsed current strengthened surface source diffusion,(iii)pulsed current strengthened bonding interface diffusion,(iv)grain growth dividing the initial large voids into nano-voids,and(v)massive grain boundaries(GBs),lattice defects,and local high-temperature strengthened GBs diffusion.Furthermore,the GBs migration across the interface was investigated,and the results revealed that the GBs migration and fine grains(350 nm)near the bonding interface together increased the joint strength.展开更多
A key component of future lunar missions is the concept of in-situ resource utilization(ISRU),which involves the use of local resources to support human missions and reduce dependence on Earth-based supplies.This pape...A key component of future lunar missions is the concept of in-situ resource utilization(ISRU),which involves the use of local resources to support human missions and reduce dependence on Earth-based supplies.This paper investigates the thermal processing capability of lunar regolith without the addition of binders,with a focus on large-scale applications for the construction of lunar habitats and infrastructure.The study used a simulant of lunar regolith found on the Schr?dinger Basin in the South Pole region.This regolith simulant consists of20 wt%basalt and 80 wt%anorthosite.Experiments were conducted using a high power CO_(2)laser to sinter and melt the regolith in a 80 mm diameter laser spot to evaluate the effectiveness of direct large area thermal processing.Results indicated that sintering begins at approximately 1180℃and reaches full melt at temperatures above 1360℃.Sintering experiments with this material revealed the formation of dense samples up to 11 mm thick,while melting experiments successfully produced larger samples by overlapping molten layers and additive manufacturing up to 50 mm thick.The energy efficiency of the sintering and melting processes was compared.The melting process was about 10 times more energy efficient than sintering in terms of material consolidation,demonstrating the promising potential of laser melting technologies of anorthosite-rich regolith for the production of structural elements.展开更多
基金the National Key Research and Development Program of China(No.2023YFC3707001).
文摘In recent years,an increase in the content of Zn,the impurity element,in ironmaking raw materials has led to the deterioration of iron-bearing resources and has introduced new challenges to sintering dezincification.A thorough understanding of the reaction behavior of Zn during the sintering process can form a theoretical foundation for the development of efficient dezincification technology.Therefore,the reaction behavior of Zn was investigated under different temperatures and atmospheres using thermodynamic calculations and experimental simulations,and the phase transformation of Zn in each pre-reductive sintering zone was investigated.The results showed that Zn-containing materials were mainly converted into ZnO when the temperature reached 700℃,and ZnO began to combine with Fe_(2)O_(3)to form ZnFe_(2)O_(4)at approximately 800℃.At low CO concentration,ZnFe_(2)O_(4)was stable,while ZnO combined with iron oxide to form Fe_(0.85-x)Zn_(x)O in a strong reduction atmosphere.ZnFe_(2)O_(4)could also be converted into Fe_(0.85-x)Zn_(x)O and FeO.A part of Zn was converted to elemental Zn,which was volatilized and removed into the gas phase above 1000℃.Therefore,the feasibility of dezincification via pre-reductive sintering was confirmed.At the coke ratio of 18.0 wt.%of the sintering material,the Zn removal rate reached 62.3 wt.%.
基金supported by the Jilin Provincial Natural Science Foundation(No.20240101118JC)the funds of Medical+X cross innovation team granted by medical department of Jilin University(No.2022JBGS07)+1 种基金the Jilin Province Science and Technology development project(No.20210101437JC)the WU JIEPING Medical Foundation(No.320.6750.2023-3-20 to TGM)。
文摘The cold sintering process(CSP)is a green and innovative method of material densification at low temperatures(<350°C).The traditional CSP entails the addition of liquid phases as a solvent to achieve material densification through the dissolution-precipitation mechanism.However,it is difficult to realize for materials with low solubility.To address this challenge,a universal cold sintering method without the addition of liquid phases has been proposed in this work.The addition of a special polyester-polymer assisted the densification of insoluble ceramics,and hydroxyapatite(HA)and Al_(2)O_(3)were successfully sintered below 100°C,achieving 95-100%densities in a short time(5-20 min).This achievement can be attributed to the low glass transition temperature and the abundance of active sites(C=O)of the polyester-polymer.The denser ceramics exhibited enhanced mechanical properties,with the compression strength of polymer-assisted CSP HA increasing by 147.3%compared to the nanoparticles.Additionally,serving as an advanced bone substitute material,HA underwent quantitative analysis using the CCK-8 method and assessed the impact of polymer presence on cell proliferation and cytotoxicity.Meanwhile,a tight bonding between the polymer and ceramic materials was achieved during CSP,providing a generalized method for designing multifunctional ceramic-polymer.
基金supported by the Key Research and Development Program of Gansu Province(22YF7FA070)the National Natural Science Foundation of China(22406076,22466026)the Basic Research Project of Yunnan Province(202301BE070001-017,202401CF070139,202401AS070085)。
文摘Iron and steel industry is one of the main sources of air pollution emissions in China.The sintering process is an important link in the blast furnace ironmaking process,but it is also accompanied by a large number of pollutants.Under the background of ultra-low emissions,iron and steel enterprises urgently need to upgrade their existing processes to address the existing process in practical application problems.In this study,a steel group in Gansu Province was taken as an example.By comparing and analyzing the pollutant emission characteristics before and after the ultra-low emission retrofit,the collaborative control effect of the combined process on SO_(2),NO_(x),particulate matter,and dioxins after the new retrofit was systematically evaluated.The results show that after the retrofit,the concentrations of particulate matter,SO_(2) and NO_(x) have dropped to near-zero levels,and the dioxin removal efficiency has reached 98.87%,with all indicators being better than the national ultra-low emission standards.The study confirms that the optimal combination of multi-pollutant collaborative treatment technologies is the key to achieving efficient emission reduction,among which selective catalytic reduction technology has a particularly significant synergistic removal effect on NO_(x) and dioxins.This study provides an important technical reference and practical basis for the ultra-low emission retrofit of the steel industry,and has important guiding significance for promoting the green retrofit of the industry.Its ultra-low emission retrofit is of great significance for achieving green and low-carbon development.
基金supported by the National Natural Science Foundation of China(No.51874368)。
文摘The use of high entropy alloy as a binder for tungsten heavy alloys offers potential advantages.The 95W-5CoCrFeMnNi alloys(95W-HEAs)were prepared via powder metallurgy at sintering temperatures of 1400−1550℃.The microstructure analysis revealed that the tungsten phase in 95W-HEAs exhibited a nearly spherical morphology in the HEA binder matrix and the formation of a Cr−Mn oxide mixed phase was observed.The sintering temperature exerted a significant influence on the relative density,grain size,W−W contiguity,and mechanical properties of the alloys.The optimal performance was achieved when sintering at 1450℃,yielding a relative density of 96.61%,a W−W contiguity of 0.528,an average grain size of 18.97μm,a compressive strength of 2234.82 MPa,and a hardness of HV 400.6.The activation energy for the diffusion of tungsten in the liquid phase formed by HEA binder was calculated to be 354.514 kJ/mol,highlighting its role in controlling grain growth.
文摘This study investigated enhancing the wear resistance of Ti6Al4V alloys for medical applications by incorporating Ti C nanoreinforcements using advanced spark plasma sintering(SPS). The addition of up to 2.5wt% Ti C significantly improved the mechanical properties, including a notable 18.2% increase in hardness(HV 332). Fretting wear tests against 316L stainless steel(SS316L) balls demonstrated a 20wt%–22wt% reduction in wear volume in the Ti6Al4V/Ti C composites compared with the monolithic alloy. Microstructural analysis revealed that Ti C reinforcement controlled the grain orientation and reduced the β-phase content, which contributed to enhanced mechanical properties. The monolithic alloy exhibited a Widmanstätten lamellar microstructure, while increasing the Ti C content modified the wear mechanisms from ploughing and adhesion(0–0.5wt%) to pitting and abrasion(1wt%–2.5wt%). At higher reinforcement levels, the formation of a robust oxide layer through tribo-oxide treatment effectively reduced the wear volume by minimizing the abrasive effects and plastic deformation. This study highlights the potential of SPS-mediated Ti C reinforcement as a transformative approach for improving the performance of Ti6Al4V alloys, paving the way for advanced medical applications.
基金supported by the National Natural Science Foundation of China(Grant No.52474347)Postdoctoral Science Foundation of China(Grant No.2024T171095)the Fundamental Research Funds for the Central Universities(Grant No.2024CDJXY003).
文摘Coke oven gas(COG)and natural gas(NG),both high-calorific by-products derived from the steel industry,have gained prominence as alternative fuels in the sintering process,thereby supporting dual objectives of emission reduction and carbon neutrality.While existing research on hydrogen-rich gas injection has predominantly concentrated on conventional thin-bed sintering,investigations into its application within thick-bed sintering remain comparatively scarce.Thick-bed sintering,recognized for enhancing energy efficiency and increasing sinter output,encounters challenges such as uneven heat distribution and diminished permeability,which can negatively impact process efficiency and product quality.To address these issues,sinter pot experiments were conducted to assess the effects of NG and COG injection on thick-bed sintering performance.Findings reveal that NG injection in thick beds mirrors the behavior observed in conventional thin-bed sintering,effectively optimizing the process and achieving a carbon reduction potential exceeding 10%.In contrast,COG injection in thick-bed conditions demonstrates notable differences,substantially lowering the solid fuel consumption rate but detrimentally affecting sinter strength and overall production.However,by optimizing the timing of COG injection,it is feasible to improve sinter yield while concurrently reducing solid fuel usage.These outcomes provide valuable insights for the advancement of gas injection technologies in thick-bed sintering,thereby contributing to energy conservation and emission mitigation efforts within the sintering industry.
基金supported by the General Program of the National Natural Science Foundation of China(No.52274326)the China Baowu Low Carbon Metallurgy Innovation Foundation(No.BWLCF202109)the Seventh Batch of Ten Thousand Talents Plan of China(No.ZX20220553).
文摘Sinter is the core raw material for blast furnaces.Flue pressure,which is an important state parameter,affects sinter quality.In this paper,flue pressure prediction and optimization were studied based on the shapley additive explanation(SHAP)to predict the flue pressure and take targeted adjustment measures.First,the sintering process data were collected and processed.A flue pressure prediction model was then constructed after comparing different feature selection methods and model algorithms using SHAP+extremely random-ized trees(ET).The prediction accuracy of the model within the error range of±0.25 kPa was 92.63%.SHAP analysis was employed to improve the interpretability of the prediction model.The effects of various sintering operation parameters on flue pressure,the relation-ship between the numerical range of key operation parameters and flue pressure,the effect of operation parameter combinations on flue pressure,and the prediction process of the flue pressure prediction model on a single sample were analyzed.A flue pressure optimization module was also constructed and analyzed when the prediction satisfied the judgment conditions.The operating parameter combination was then pushed.The flue pressure was increased by 5.87%during the verification process,achieving a good optimization effect.
文摘Comprehensive two-dimensional gas chromatography coupled with time-of-flight mass spectrometry （ GC x GC- TOFMS） was applied to the quick qualitative analysis of 17 types of polychlorinated dibenzo-p-dioxins and furans （PCDD/Fs） from the iron ore sintering process. The GC x GC-TOFMS parameters were evaluated and optimized to yield a complete separation for the 17 types of PCCD/Fs from interference and to the attainment of high sensitivity. After optimization, all the 17 types of PCCD/Fs were separated within 42.5 min. The critical and most toxic tetrachlorodibenzo- p-dioxin （TCDD） detection can be up to 0.5 ~g/L. The method was used to analyze real fly ash samples. Accurate identification and determination of all the analyses were by GC x GC, mass spectrum library and ion ratio. The technique is thought to be a substitute for and a supplement to high resolution gas chromatography/high resolution mass spectrometry （HRGC/HRMS） in the field of dioxin analysis.
基金Project(52274290)supported by the National Natural Science Foundation of ChinaProject(72088101)supported by the Basic Science Center Project for National Natural Science Foundation of China。
文摘A pre-reduction sintering process with flue gas recirculation(PSP_(fsg)-FGR)was developed to mitigate alkalis harm to the blast furnace and reduce the flue gas emission in the whole ironmaking process.The results indicated that the pre-reduction sintering process(PSP)can effectively remove 58.02%of K and 30.68%of Na from raw mixtures and improve yield and tumbler index to 74.40%and 68.69%,respectively.Moreover,PSP was conducive to reducing NO_(x) and SO_(2)emissions and simultaneously increasing CO content in flue gas.Circulating CO-containing flue gas to sintering bed effectively recycled CO and further improved K and Na removal ratio to 74.11%and 32.92%,respectively.Microstructural analysis revealed that the pre-reduced sinter mainly consisted of magnetite,wustite and a small quantity of metallic iron,and very few silicate glass phase was also formed.This process can simultaneously realize alkali metal elements removal as well as flue gas emission reduction from the integrated ironmaking process.
基金supported by the Basic Science Center Project for the National Natural Science Foundation of China(No.72088101)the S&T Program of Hebei(No.23564101D).
文摘As the bed depth increases,sintering yield increases,but the productivity decreases.To reveal the reasons for the decrease in productivity and explore targeted solutions,the bed resistance of mixtures,wet zone,and combustion zone was analyzed in the laboratory.The results showed that the decreased porosity of mixture resulted in the increased bed resistance by 160.56%when the bed depth increased from 600 to 1000 mm.After improving porosity of 1%by adding loosening bars with optimized size and distribution,the bed resistance decreased,and the productivity increased by 5%.The increase in bed depth increased the thickness of the wet zone from 120 to 680 mm and the resistance from 1.56 to 8.83 kPa.By using a three-stage intensive mixer and pre-adding water for granulation,the moisture of mixture was reduced by 0.6%,and the sintering productivity increased by 4%.Besides,the high bed resistance is mainly caused by the increase in the thickness of the combustion zone from 31.9 to 132.7 mm,and the bed resistance increased from 0.70 to 5.62 kPa.The bed resistance of the combustion zone at 900 mm was increased by 90.51%compared to 700 mm.After optimization of the distribution of coke breeze,the thickness of combustion zone at the lower layer decreased from 132.7 to 106.84 mm and permeability improved significantly.
基金financially supported by the National Nat-ural Science Foundation of China(Nos.U22A20185,52175302,and U21A20128)the National MCF Energy R&D Program(No.2019YFE03100100)the Fundamental Research Funds for the Central Universities(No.2022FRFK060009).
文摘The challenge of low temperature and rapid diffusion bonding of a Ni-based superalloy was hereby addressed by using a Ni nano-coating and a spark plasma sintering(SPS).It successfully produced a Nibased superalloy joint with 337 MPa shear strength at 500℃ for 30 min,which is approximately 400℃ lower than the traditional hot pressure diffusion bonding(HPDB)temperature.The microstructure and mechanical properties of the joints were systematically investigated.It is revealed that the pulsed current and ultra-fine grains(19 nm)in the Ni nano-coating could significantly facilitate voids closure.The voids closure mechanisms involved(i)pulsed current strengthened plastic deformation,(ii)pulsed current strengthened surface source diffusion,(iii)pulsed current strengthened bonding interface diffusion,(iv)grain growth dividing the initial large voids into nano-voids,and(v)massive grain boundaries(GBs),lattice defects,and local high-temperature strengthened GBs diffusion.Furthermore,the GBs migration across the interface was investigated,and the results revealed that the GBs migration and fine grains(350 nm)near the bonding interface together increased the joint strength.
文摘A key component of future lunar missions is the concept of in-situ resource utilization(ISRU),which involves the use of local resources to support human missions and reduce dependence on Earth-based supplies.This paper investigates the thermal processing capability of lunar regolith without the addition of binders,with a focus on large-scale applications for the construction of lunar habitats and infrastructure.The study used a simulant of lunar regolith found on the Schr?dinger Basin in the South Pole region.This regolith simulant consists of20 wt%basalt and 80 wt%anorthosite.Experiments were conducted using a high power CO_(2)laser to sinter and melt the regolith in a 80 mm diameter laser spot to evaluate the effectiveness of direct large area thermal processing.Results indicated that sintering begins at approximately 1180℃and reaches full melt at temperatures above 1360℃.Sintering experiments with this material revealed the formation of dense samples up to 11 mm thick,while melting experiments successfully produced larger samples by overlapping molten layers and additive manufacturing up to 50 mm thick.The energy efficiency of the sintering and melting processes was compared.The melting process was about 10 times more energy efficient than sintering in terms of material consolidation,demonstrating the promising potential of laser melting technologies of anorthosite-rich regolith for the production of structural elements.
