Non-Darcian flow in rock fractures exhibits significant anisotropic characteristics,which can be affected by mechanical processes,such as cyclic shearing.Understanding the evolution of anisotropic nonDarcian flow is c...Non-Darcian flow in rock fractures exhibits significant anisotropic characteristics,which can be affected by mechanical processes,such as cyclic shearing.Understanding the evolution of anisotropic nonDarcian flow is crucial for characterizing groundwater flow and mass/heat transport in fractured rock masses.In this study,we conducted experiments on non-Darcian flow in single rough fractures under cyclic shearing conditions,aiming to analyze the anisotropic evolution of inertial permeability and viscous permeability.We established quantitative characterization models for the two types of permeability.First,we conducted cyclic shearing experiments on four sets of 24 rough rock fractures,investigating their shear characteristics.Then,we performed 480 non-Darcian flow experiments to analyze the anisotropic evolution of viscous permeability and inertial permeability of these rock fractures.The results showed that viscous permeability exhibited significant differences only in the orthogonal direction,while inertial permeability exhibited differences in both orthogonal and opposite directions.With increase in the shear cycles,the differences in the orthogonal direction gradually increased,while those in opposite direction gradually decreased.Finally,we established characterization equations for the two permeabilities based on the proposed directional geometric parameters and validated the performance of these equations with experimental data.These findings are useful for the quantitative characterization of the evolution of non-Darcian flow in fractures under dynamic loading conditions.展开更多
This study conducted the experimental investigation of aerodynamic heating of Micro-scale Rotational Shearing Flow with Axial Limited-Length(MRSFALL).The temperature riseof the stator is captured by the high response ...This study conducted the experimental investigation of aerodynamic heating of Micro-scale Rotational Shearing Flow with Axial Limited-Length(MRSFALL).The temperature riseof the stator is captured by the high response thermocouples.The eccentricity ratio and clearanceheight are guaranteed by means of instantaneous trajectory and torsion monitoring of the rotator.The result shows that the maximum temperature rise takes place upstream of the minimum clear-ance height along circumferential direction.The distribution of temperature rise presents asymmet-ric curve along axial direction,and peak value occurs near the dimensionless axial position of-0.18.The effect of aerodynamic heating becomes notable as the rotational speed is larger than3×10^(4)r/min.The effect of end leakage and the viscous dissipation have great impact on temper-ature rise of MRSFALL.More specially,the peak value of temperature rise at dimensionless clear-ance height of 0.0080 is larger than the case at dimensionless clearance height of 0.0044.Furthermore,when the eccentricity ratio is too large,the viscous dissipation is induced,and theadditional temperature rise is achieved.The heat flux identification of shear flow has been realizedby Sequential Function Specification Method(SFSM)and its estimation of thermal load has been given.The heat flux induced by the aerodynamic heating in this study varies from 950 W/m^(2)to1330 W/m^(2).展开更多
A conceptual model of intermittent joints is introduced to the cyclic shear test in the laboratory to explore the effects of loading parameters on its shear behavior under cyclic shear loading.The results show that th...A conceptual model of intermittent joints is introduced to the cyclic shear test in the laboratory to explore the effects of loading parameters on its shear behavior under cyclic shear loading.The results show that the loading parameters(initial normal stress,normal stiffness,and shear velocity)determine propagation paths of the wing and secondary cracks in rock bridges during the initial shear cycle,creating different morphologies of macroscopic step-path rupture surfaces and asperities on them.The differences in stress state and rupture surface induce different cyclic shear responses.It shows that high initial normal stress accelerates asperity degradation,raises shear resistance,and promotes compression of intermittent joints.In addition,high normal stiffness provides higher normal stress and shear resistance during the initial cycles and inhibits the dilation and compression of intermittent joints.High shear velocity results in a higher shear resistance,greater dilation,and greater compression.Finally,shear strength is most sensitive to initial normal stress,followed by shear velocity and normal stiffness.Moreover,average dilation angle is most sensitive to initial normal stress,followed by normal stiffness and shear velocity.During the shear cycles,frictional coefficient is affected by asperity degradation,backfilling of rock debris,and frictional area,exhibiting a non-monotonic behavior.展开更多
Landslides frequently occurred in Jurassic red strata in the Three Gorges Reservoir(TGR)region in China.The Jurassic strata consist of low mechanical strength and poor permeability of weak silty mudstone layer,which m...Landslides frequently occurred in Jurassic red strata in the Three Gorges Reservoir(TGR)region in China.The Jurassic strata consist of low mechanical strength and poor permeability of weak silty mudstone layer,which may cause slope instability during rainfall.In order to understand the strength behavior of Jurassic silty mudstone shear zone,the so-called Shizibao landslide located in Guojiaba Town,Zigui County,Three Gorges Reservoir(TGR)in China is selected as a case study.The shear strength of the silty mudstone shear zone is strongly influenced by both the water content and the normal stress.Therefore,a series of drained ring shear tests were carried out by varying the water contents(7%,12%,17%,and 20%,respectively)and normal stresses(200,300,400,and 500 kPa,respectively).The result revealed that the residual friction coefficient and residual friction angle were power function relationships with water content and normal stress.The peak cohesion of the silty mudstone slip zone increased with water content to a certain limit,above which the cohesion decreased.In contrast,the residual cohesion showed the opposite trend,indicating the cohesion recovery above a certain limit of water content.However,both the peak and residual friction angle of the silty mudstone slip zone were observed to decrease steadily with increased water content.Furthermore,the macroscopic morphological features of the shear surface showed that the sliding failure was developed under high normal stress at low water content,while discontinuous sliding surface and soil extrusion were occurred when the water content increased to a saturated degree.The localized liquefaction developed by excess pore water pressure reduced the frictional force within the shear zone.Finally,the combined effects of the slope excavation and precipitation ultimately lead to the failure of the silty mudstone slope;however,continuous rainfall is the main factor triggering sliding.展开更多
Compared to existing deformation monitoring methods,landslide early warning can be achieved by detecting precursor signals of slope instability through acoustic emission(AE).Acquisition of AE signals generated by acti...Compared to existing deformation monitoring methods,landslide early warning can be achieved by detecting precursor signals of slope instability through acoustic emission(AE).Acquisition of AE signals generated by active waveguide facilitates monitoring the development of shear surface and provides a foundation for quantifying landslide movement.Backfill particles are the dominant AE sources in active waveguides,typically chosen from materials such as gravels or sands.However,the influence of particle sizes and gradings has not been clarified in existing laboratory models or field monitoring.This research introduces a direct shear test for active waveguide,where spherical glass beads are employed to precisely regulate the size and grading of backfill particles.A programmable logic controller maintains a constant shearing speed and equivalent total deformation.Through a comprehensive analysis of AE,deformation,and mechanical measurements,this study evaluates the impact of particle size and grading on monitoring capabilities.The findings suggest that the AE mechanism in glass beads is attributed to particle collision and dislocation,leading to AE events characterized by low amplitude and energy levels.The percentage of high-amplitude AE events rises steadily with the progression of shearing.The correlation between shear force,cumulative ring down count(RDC)of AE,and deformation conforms to a power function,with the exponent relying on particle size,grading,and shearing speed.Notably,the combination of small particles and low shearing speeds can yield the maximum cumulative RDC,while selecting particles with uneven grading will significantly enhance the intensity of AE signals from active waveguide.展开更多
Understanding the shear mechanical behaviors and instability mechanisms of rock joints under dynamic loading remains a complex challenge.This research conducts a series of direct shear tests on real rock joints subjec...Understanding the shear mechanical behaviors and instability mechanisms of rock joints under dynamic loading remains a complex challenge.This research conducts a series of direct shear tests on real rock joints subjected to cyclic normal loads to assess the influence of dynamic normal loading amplitude(F_(d)),dynamic normal loading frequency(f_(v)),initial normal loading(F_(s)),and the joint roughness coefficient(JRC)on the mechanical properties and instability responses of these joints.The results show that unstable sliding is often accompanied by friction weakening due to dynamic normal loads.A significant negative correlation exists between cyclic normal loads and the normal displacement during the shearing process.Dynamic normal load paths vary the contact states of asperities on the rough joint surfaces,impacting the stick-slip instability mechanism of the joints,which in turn affects both the magnitude and location of the stress drop during the stick-slip events,particularly during the unloading phases.An increasing F_(d) results in a more stable shearing behavior and a reduction in the amplitude of stick-slip stress drops.The variation in f_(v) influences the amplitude of stress drop for the joints during shear,characterized by an initial decrease(f_(v)=0.25-2 Hz)before exhibiting an increment(f_(v)=2-4 Hz).As F_(s) increases,sudden failures of the interlocked rough surfaces are more prone to occur,thus producing enhanced instability and a more substantial stress drop.Additionally,a larger JRC intensifies the instability of the joints,which would induce a more pronounced decline in the stick-slip stress.The Rate and state friction(RSF)law can provide an effective explanation for the unstable sliding phenomena of joints during the oscillations of normal loads.The findings may provide certain useful references for a deeper comprehension of the sliding behaviors exhibited by rock joints when subjected to cyclic dynamic disturbances.展开更多
Shearing dislocation is a common failure type for rock–backfill interfaces because of backfill sedimentation and rock strata movement in backfill mining goaf.This paper designed a test method for rock–backfill shear...Shearing dislocation is a common failure type for rock–backfill interfaces because of backfill sedimentation and rock strata movement in backfill mining goaf.This paper designed a test method for rock–backfill shearing dislocation.Using digital image techno-logy and three-dimensional(3D)laser morphology scanning techniques,a set of 3D models with rough joint surfaces was established.Further,the mechanical behavior of rock–backfill shearing dislocation was investigated using a direct shear test.The effects of interface roughness on the shear–displacement curve and failure characteristics of rock–backfill specimens were considered.The 3D fractal dimen-sion,profile line joint roughness coefficient(JRC),profile line two-dimensional fractal dimension,and the surface curvature of the frac-tures were obtained.The correlation characterization of surface roughness was then analyzed,and the shear strength could be measured and calculated using JRC.The results showed the following:there were three failure threshold value points in rock–backfill shearing dis-location:30%–50%displacement before the peak,70%–90%displacement before the peak,and 100%displacement before the peak to post-peak,which could be a sign for rock–backfill shearing dislocation failure.The surface JRC could be used to judge the rock–backfill shearing dislocation failure,including post-peak sliding,uniform variations,and gradient change,corresponding to rock–backfill disloca-tion failure on the field site.The research reveals the damage mechanism for rock–backfill complexes based on the free joint surface,fills the gap of existing shearing theoretical systems for isomerism complexes,and provides a theoretical basis for the prevention and control of possible disasters in backfill mining.展开更多
The deep cement mixing(DCM)is used to improve the capacity and reduce the settlement of the soft ground by forming cemented clay columns.The investigation on the mechanical behaviour of the DCM samples is limited to e...The deep cement mixing(DCM)is used to improve the capacity and reduce the settlement of the soft ground by forming cemented clay columns.The investigation on the mechanical behaviour of the DCM samples is limited to either laboratory-prepared samples or in-situ samples under unconfined compression.In this study,a series of drained and undrained triaxial shearing tests was performed on the in-situ cored DCM samples with high cement content to assess their mechanical behaviours.It is found that the drainage condition affects significantly the stiffness,peak and residual strengths of the DCM samples,which is mainly due to the state of excess pore water pressure at different strain levels,i.e.being positive before the peak deviatoric stress and negative after the peak deviatoric stress,in the undrained tests.The slope of the failure envelope changes obviously with the confining pressures,being steeper at lower stress levels and flatter at higher stress levels.The strength parameters,effective cohesion and friction angle obtained from lower stress levels(c′0 andφ′0)are 400 kPa and 58°,respectively,which are deemed to be true for design in most DCM applications where the in-situ stress levels are normally at lower values of 50-200 kPa.Additionally,the computed tomography(CT)scanning system was adopted to visualize the internal structures of DCM samples.It is found that the clay pockets existing inside the DCM samples due to uneven mixing affect markedly their stress-strain behaviour,which is one of the main reasons for the high variability of the DCM samples.展开更多
Understanding the anisotropic creep behaviors of shale under direct shearing is a challenging issue.In this context,we conducted shear-creep and steady-creep tests on shale with five bedding orientations (i.e.0°,...Understanding the anisotropic creep behaviors of shale under direct shearing is a challenging issue.In this context,we conducted shear-creep and steady-creep tests on shale with five bedding orientations (i.e.0°,30°,45°,60°,and 90°),under multiple levels of direct shearing for the first time.The results show that the anisotropic creep of shale exhibits a significant stress-dependent behavior.Under a low shear stress,the creep compliance of shale increases linearly with the logarithm of time at all bedding orientations,and the increase depends on the bedding orientation and creep time.Under high shear stress conditions,the creep compliance of shale is minimal when the bedding orientation is 0°,and the steady-creep rate of shale increases significantly with increasing bedding orientations of 30°,45°,60°,and 90°.The stress-strain values corresponding to the inception of the accelerated creep stage show an increasing and then decreasing trend with the bedding orientation.A semilogarithmic model that could reflect the stress dependence of the steady-creep rate while considering the hardening and damage process is proposed.The model minimizes the deviation of the calculated steady-state creep rate from the observed value and reveals the behavior of the bedding orientation's influence on the steady-creep rate.The applicability of the five classical empirical creep models is quantitatively evaluated.It shows that the logarithmic model can well explain the experimental creep strain and creep rate,and it can accurately predict long-term shear creep deformation.Based on an improved logarithmic model,the variations in creep parameters with shear stress and bedding orientations are discussed.With abovementioned findings,a mathematical method for constructing an anisotropic shear creep model of shale is proposed,which can characterize the nonlinear dependence of the anisotropic shear creep behavior of shale on the bedding orientation.展开更多
The shear mechanical behavior is regarded as an essential factor affecting the stability of the surrounding rocks in underground engineering.The shear strength and failure mechanisms of layered rock are significantly ...The shear mechanical behavior is regarded as an essential factor affecting the stability of the surrounding rocks in underground engineering.The shear strength and failure mechanisms of layered rock are significantly affected by the foliation angles.Direct shear tests were conducted on cubic slate samples with foliation angles of 0°,30°,45°,60°,and 90°.The effect of foliation angles on failure patterns,acoustic emission(AE)characteristics,and shear strength parameters was analyzed.Based on AE characteristics,the slate failure process could be divided into four stages:quiet period,step-like increasing period,dramatic increasing period,and remission period.A new empirical expression of cohesion for layered rock was proposed,which was compared with linear and sinusoidal cohesion expressions based on the results made by this paper and previous experiments.The comparative analysis demonstrated that the new expression has better prediction ability than other expressions.The proposed empirical equation was used for direct shear simulations with the combined finite-discrete element method(FDEM),and it was found to align well with the experimental results.Considering both computational efficiency and accuracy,it was recommended to use a shear rate of 0.01 m/s for FDEM to carry out direct shear simulations.To balance the relationship between the number of elements and the simulation results in the direct shear simulations,the recommended element size is 1 mm.展开更多
Some rock joints exhibit significant brittleness,characterized by a sharp decrease in shear stress upon reaching the peak strength.However,existing models often fail to accurately represent this behavior and are encum...Some rock joints exhibit significant brittleness,characterized by a sharp decrease in shear stress upon reaching the peak strength.However,existing models often fail to accurately represent this behavior and are encumbered by numerous parameters lacking clear mechanical significance.This study presents a new statistical damage constitutive model rooted in both damage mechanics and statistics,containing only three model parameters.The proposed model encompasses all stages of joint shearing,including the compaction stage,linear stage,plastic yielding stage,drop stage,strain softening stage,and residual strength stage.To derive the analytical expression of the constitutive model,three boundary conditions are introduced.Experimental data from both natural and artificial rock joints is utilized to validate the model,resulting in average absolute relative errors ranging from 3%to 8%.Moreover,a comparative analysis with established models illustrates that the proposed model captures stress drop and post-peak strain softening more effectively,with model parameters possessing clearer mechanical interpretations.Furthermore,parameter analysis is conducted to investigate the impacts of model parameters on the curves and unveil the relationship between these parameters and the mechanical properties of rock joints.Importantly,the proposed model is straightforward in form,and all model parameters can be obtained from direct shear tests,thus facilitating the utilization in numerical simulations.展开更多
Blade clearance is an important technical parameter of the shear, which determines the shear quality of plate. The finite element method was used to simulate shearing process which is in the different specifications a...Blade clearance is an important technical parameter of the shear, which determines the shear quality of plate. The finite element method was used to simulate shearing process which is in the different specifications and blade clearances, and the impact on blade section and shearing force of blade clearance was analyzed. Comparing with traditional experience formulas and measured values, the limitations of the experience formulas were proved. And by contrasting with the shearing force data collected from Linfen Iron and Steel Company, the reliability of the finite element method was further proved. The simulated results show that the simulated values controlled by ductile fracture criterion and measured values are very close, and the deviation value is in the range of 4.8%-20.8%. For the same steel, if the plate is thicker, the blade clearance will be greater, and thickness and blade clearance are approximately linear. The difference between numerical simulation of the maximum shearing force and the measured results is 7.7% to 12.0%, and the simulation results are close to facts. With the increase of blade clearance and the thickness, the shearing force was increased to some degree.展开更多
The shearing/cooling roll （SCR） process was adopted to prepare semi-solid A2017 alloy. The formation and evolution of non-dendritic microstructures in semi-solid A2017 alloy were studied. It is shown that the micros...The shearing/cooling roll （SCR） process was adopted to prepare semi-solid A2017 alloy. The formation and evolution of non-dendritic microstructures in semi-solid A2017 alloy were studied. It is shown that the microstructures of semi-solid billets transform from coarse dendrites into fine equiaxed grains as the pouring temperature of molten alloy decreases o.r roll-shoe cavity height is reduced. From the inlet to the exit of roll-shoe cavity, microstructure of semi-solid slurry near the shoe surface is in the order of coarse dendrites, degenerated dendrites or equiaxed grains, but fine equiaxed grains are near the roll surface. Microstructural evolution of semi-solid slurry prepared by SCR process is that the molten alloy nucleates and grows into dendrite firstly on the roll and shoe＇s surface. Under the shearing and stirring given by the rotating roll, the dendrites crush off and disperse into the melt. Under the shearing and stirring on semi-solid slurry with high volume fraction of solid, the dendrite arms fracture and form equiaxed grain microstructures.展开更多
A novel extrusion-shearing(ES) composite process was designed to fabricate fine-grained, high strength and tough magnesium alloy. The structural parameters of an ES die were optimized by conducting an orthogonal simul...A novel extrusion-shearing(ES) composite process was designed to fabricate fine-grained, high strength and tough magnesium alloy. The structural parameters of an ES die were optimized by conducting an orthogonal simulation experiment using finite element software Deform-3D, and Mg-3 Zn-0.6 Ca-0.6 Zr(ZXK310) alloy was processed using the ES die. The results show that the optimized structural parameters of ES die are extrusion angle(α) of 90°, extrusion section height(h) of 15 mm and inner fillet radius(r) of 10 mm. After ES at an extrusion temperature and a die temperature of 350 °C, ZXK310 alloy exhibited good ES forming ability, and obvious dynamic recrystallization occurred in the forming area. The grain size decreased from 1.42 μm of extrusion area to 0.85 μm of the forming area. Owing to the pinning of second phase and formation of ultrafine grains, the tensile strength, yield strength and elongation of alloy reached 362 MPa, 289 MPa and 21.7%, respectively.展开更多
The Ailaoshan-Red River（ASRR） shear zone in SW China represents an important discontinuity believed to have accommodated eastward extrusion of the Tibetan Plateau in response to the collision of the Indian and Euras...The Ailaoshan-Red River（ASRR） shear zone in SW China represents an important discontinuity believed to have accommodated eastward extrusion of the Tibetan Plateau in response to the collision of the Indian and Eurasian plates. The onset timing and duration of the ASRR sinistral strike-slip shearing have been hotly disputed. In this paper we present new zircon LA-ICP-MS U-Pb geochronological data from six syntectonic granitic mylonite and leucosomes samples from the ASRR shear zone. Our data reveal a metamorphic age of ~40 Ma, most likely suggesting the maximum age of the shearing initiation. Rocks showing syn-kinematic signatures yield crystallization ages of 38–22 Ma, with inherited components ranging from 716 to 108 Ma. These results, together with existing geological and geochronological data, indicate that the sinistral shearing along the ASRR zone probably began at 40 Ma, mainly activated at 29–22 Ma and lasted at least to ~22 Ma. Our data suggest a continuous extrusion between the Indochina and South China blocks during ~35–17 Ma. The ASRR sinistral shearing has accommodated large scale eastward displacement of the southeastern Tibetan syntaxis, and is likely responsible for the opening of the South China Sea.展开更多
A hybrid finite-discrete element method was implemented to study the fracture process of rough rock joints under direct shearing. The hybrid method reproduced the joint shear resistance evolution process from asperity...A hybrid finite-discrete element method was implemented to study the fracture process of rough rock joints under direct shearing. The hybrid method reproduced the joint shear resistance evolution process from asperity sliding to degradation and from gouge formation to grinding. It is found that, in the direct shear test of rough rock joints under constant normal displacement loading conditions, higher shearing rate promotes the asperity degradation but constraints the volume dilation, which then results in higher peak shear resistance, more gouge formation and grinding, and smoother new joint surfaces. Moreover, it is found that the joint roughness affects the joint shear resistance evolution through influencing the joint fracture micro mechanism. The asperity degradation and gouge grinding are the main failure micro-mechanism in shearing rougher rock joints with deeper asperities while the asperity sliding is the main failure micro-mechanism in shearing smoother rock joints with shallower asperities. It is concluded that the hybrid finite-discrete element method is a valuable numerical tool better than traditional finite element method and discrete element method for modelling the joint sliding, asperity degradation, gouge formation, and gouge grinding occurred in the direct shear tests of rough rock joints.展开更多
The existing investigations on piezoelectric materials containing an elliptic hole mainly focus on remote uniform tensile loads. In order to have a better understanding of the fracture behavior of piezoelectric materi...The existing investigations on piezoelectric materials containing an elliptic hole mainly focus on remote uniform tensile loads. In order to have a better understanding of the fracture behavior of piezoelectric materials under different loading conditions, theoretical and numerical solutions are presented for an elliptic hole in transversely isotropic piezoelectric materials subjected to uniform internal shearing forces based on the complex potential approach. By solving ten variable linear equations, the analytical solutions inside and outside the hole satisfying the permeable electric boundary conditions are obtained. Taking PZT-4 ceramic into consideration, numerical results of electro-elastic fields along the edge of the hole and axes, and the electric displacements in the hole are presented. Comparison with stresses in transverse isotropic elastic materials shows that the hoop stress at the ends of major axis in two kinds of material equals zero for the various ratios of major to minor axis lengths; If the ratio is greater than 1, the hoop stress in piezoelectric materials is smaller than that in elastic materials, and if the ratio is smaller than 1, the hoop stress in piezoelectric materials is greater than that in elastic materials; When it is a circle hole, the shearing stress in two materials along axes is the same. The distribution of electric displacement components shows that the vertical electric displacement in the hole and along axes in the material is always zero though under the permeable electric boundary condition; The horizontal and vertical electric displacement components along the edge of the hole are symmetrical and antisymmetrical about horizontal axis, respectively. The stress and electric displacement distribution tends to zero at distances far from the elliptical hole, which conforms to the conclusion usually made on the basis of Saint-Venant’s principle. Unlike the existing work, uniform shearing forces acting on the edge of the hole, and the distribution of electro-elastic fields inside and outside the elliptic hole are considered.展开更多
A self-designed setup of modified sloping cooling/shearing process was made to prepare the semisolid Al-3wt%Mg alloy. A three-dimensional simulation model was established for the analysis of preparing the semisolid Al...A self-designed setup of modified sloping cooling/shearing process was made to prepare the semisolid Al-3wt%Mg alloy. A three-dimensional simulation model was established for the analysis of preparing the semisolid Al-3wt%Mg alloy. Through simulation and experiment, it is shown that the sloping angle of the plate greatly affects temperature and velocity distributions, and the temperature and velocity of the alloy at the exit of the sloping plate increase with the increase of the sloping angle. The alloy temperature decreases linearly from the pouring mouth to the exit. The alloy temperature at the exit increases obviously with the increase of pouring temperature. To prepare the semisolid Al-3wt%Mg alloy with good quality, the sloping angle θ=45° is reasonable, and the pouring temperature is suggested to be designed above 650-660℃ but under 700℃.展开更多
Punch shearing is used to form the part in the material process.Cryogenic treatment(CT)has active effect on local mechanical properties of steel,but it is still uncertain of the influence of CT on the properties of th...Punch shearing is used to form the part in the material process.Cryogenic treatment(CT)has active effect on local mechanical properties of steel,but it is still uncertain of the influence of CT on the properties of the magnesium alloy during punch shearing.In this work,the influence of AZ31 sheet treated by cryogenic on punch shearing was studied.Microstructures were observed with a ZEISS optical microscope,and mechanical properties,as well as shear properties were tested by tensile testing and punch shearing.The results show that the number of secondary phase increases and a large number of twins appear in the grains after CT.Meanwhile,the ultimate tensile strength(UTS),the ductility,and hardness of AZ31 are improved,while the yield strength(YS)decreases gradually during CT.During punch shearing,the shearing strength decreases,the rollover radius changes insignificantly,and the height of the burr on the edge of the cross section decreases.At the same time,a larger proportion of smooth zone on the cross section has been achieved.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.42202316)the China Postdoctoral Science Foundation(Grant No.2022M712963)the Open Fund of Badong National Observation and Research Station of Geohazards(Grant No.BNORSG-202309).
文摘Non-Darcian flow in rock fractures exhibits significant anisotropic characteristics,which can be affected by mechanical processes,such as cyclic shearing.Understanding the evolution of anisotropic nonDarcian flow is crucial for characterizing groundwater flow and mass/heat transport in fractured rock masses.In this study,we conducted experiments on non-Darcian flow in single rough fractures under cyclic shearing conditions,aiming to analyze the anisotropic evolution of inertial permeability and viscous permeability.We established quantitative characterization models for the two types of permeability.First,we conducted cyclic shearing experiments on four sets of 24 rough rock fractures,investigating their shear characteristics.Then,we performed 480 non-Darcian flow experiments to analyze the anisotropic evolution of viscous permeability and inertial permeability of these rock fractures.The results showed that viscous permeability exhibited significant differences only in the orthogonal direction,while inertial permeability exhibited differences in both orthogonal and opposite directions.With increase in the shear cycles,the differences in the orthogonal direction gradually increased,while those in opposite direction gradually decreased.Finally,we established characterization equations for the two permeabilities based on the proposed directional geometric parameters and validated the performance of these equations with experimental data.These findings are useful for the quantitative characterization of the evolution of non-Darcian flow in fractures under dynamic loading conditions.
基金supports from the National Natural Science Foundation of China(No.52206091)the Aeronautical Science Foundation of China(No.201928052008)the Natural Science Foundation of Jiangsu Province,China(No.BK20210303)。
文摘This study conducted the experimental investigation of aerodynamic heating of Micro-scale Rotational Shearing Flow with Axial Limited-Length(MRSFALL).The temperature riseof the stator is captured by the high response thermocouples.The eccentricity ratio and clearanceheight are guaranteed by means of instantaneous trajectory and torsion monitoring of the rotator.The result shows that the maximum temperature rise takes place upstream of the minimum clear-ance height along circumferential direction.The distribution of temperature rise presents asymmet-ric curve along axial direction,and peak value occurs near the dimensionless axial position of-0.18.The effect of aerodynamic heating becomes notable as the rotational speed is larger than3×10^(4)r/min.The effect of end leakage and the viscous dissipation have great impact on temper-ature rise of MRSFALL.More specially,the peak value of temperature rise at dimensionless clear-ance height of 0.0080 is larger than the case at dimensionless clearance height of 0.0044.Furthermore,when the eccentricity ratio is too large,the viscous dissipation is induced,and theadditional temperature rise is achieved.The heat flux identification of shear flow has been realizedby Sequential Function Specification Method(SFSM)and its estimation of thermal load has been given.The heat flux induced by the aerodynamic heating in this study varies from 950 W/m^(2)to1330 W/m^(2).
基金financially supported by the National Natural Science Foundation of China(Grant No.42172292)Taishan Scholars Project Special Funding,and Shandong Energy Group(Grant No.SNKJ 2022A01-R26).
文摘A conceptual model of intermittent joints is introduced to the cyclic shear test in the laboratory to explore the effects of loading parameters on its shear behavior under cyclic shear loading.The results show that the loading parameters(initial normal stress,normal stiffness,and shear velocity)determine propagation paths of the wing and secondary cracks in rock bridges during the initial shear cycle,creating different morphologies of macroscopic step-path rupture surfaces and asperities on them.The differences in stress state and rupture surface induce different cyclic shear responses.It shows that high initial normal stress accelerates asperity degradation,raises shear resistance,and promotes compression of intermittent joints.In addition,high normal stiffness provides higher normal stress and shear resistance during the initial cycles and inhibits the dilation and compression of intermittent joints.High shear velocity results in a higher shear resistance,greater dilation,and greater compression.Finally,shear strength is most sensitive to initial normal stress,followed by shear velocity and normal stiffness.Moreover,average dilation angle is most sensitive to initial normal stress,followed by normal stiffness and shear velocity.During the shear cycles,frictional coefficient is affected by asperity degradation,backfilling of rock debris,and frictional area,exhibiting a non-monotonic behavior.
基金funded by the National Science Foundation of China(CN)(Nos.42090054,41922055,41931295)the Key Research and Development Program of Hubei Province of China(No.2020BCB079)。
文摘Landslides frequently occurred in Jurassic red strata in the Three Gorges Reservoir(TGR)region in China.The Jurassic strata consist of low mechanical strength and poor permeability of weak silty mudstone layer,which may cause slope instability during rainfall.In order to understand the strength behavior of Jurassic silty mudstone shear zone,the so-called Shizibao landslide located in Guojiaba Town,Zigui County,Three Gorges Reservoir(TGR)in China is selected as a case study.The shear strength of the silty mudstone shear zone is strongly influenced by both the water content and the normal stress.Therefore,a series of drained ring shear tests were carried out by varying the water contents(7%,12%,17%,and 20%,respectively)and normal stresses(200,300,400,and 500 kPa,respectively).The result revealed that the residual friction coefficient and residual friction angle were power function relationships with water content and normal stress.The peak cohesion of the silty mudstone slip zone increased with water content to a certain limit,above which the cohesion decreased.In contrast,the residual cohesion showed the opposite trend,indicating the cohesion recovery above a certain limit of water content.However,both the peak and residual friction angle of the silty mudstone slip zone were observed to decrease steadily with increased water content.Furthermore,the macroscopic morphological features of the shear surface showed that the sliding failure was developed under high normal stress at low water content,while discontinuous sliding surface and soil extrusion were occurred when the water content increased to a saturated degree.The localized liquefaction developed by excess pore water pressure reduced the frictional force within the shear zone.Finally,the combined effects of the slope excavation and precipitation ultimately lead to the failure of the silty mudstone slope;however,continuous rainfall is the main factor triggering sliding.
基金funding support from the National Natural Science Foundation of China(Grant No.52404224)Beijing Natural Science Foundation(Grant No.8244051)the fellowship of China National Postdoctoral Program for Innovative Talents(Grant No.BX20230175).
文摘Compared to existing deformation monitoring methods,landslide early warning can be achieved by detecting precursor signals of slope instability through acoustic emission(AE).Acquisition of AE signals generated by active waveguide facilitates monitoring the development of shear surface and provides a foundation for quantifying landslide movement.Backfill particles are the dominant AE sources in active waveguides,typically chosen from materials such as gravels or sands.However,the influence of particle sizes and gradings has not been clarified in existing laboratory models or field monitoring.This research introduces a direct shear test for active waveguide,where spherical glass beads are employed to precisely regulate the size and grading of backfill particles.A programmable logic controller maintains a constant shearing speed and equivalent total deformation.Through a comprehensive analysis of AE,deformation,and mechanical measurements,this study evaluates the impact of particle size and grading on monitoring capabilities.The findings suggest that the AE mechanism in glass beads is attributed to particle collision and dislocation,leading to AE events characterized by low amplitude and energy levels.The percentage of high-amplitude AE events rises steadily with the progression of shearing.The correlation between shear force,cumulative ring down count(RDC)of AE,and deformation conforms to a power function,with the exponent relying on particle size,grading,and shearing speed.Notably,the combination of small particles and low shearing speeds can yield the maximum cumulative RDC,while selecting particles with uneven grading will significantly enhance the intensity of AE signals from active waveguide.
基金funding support from the National Natural Science Foundation of China(Grant Nos.52174092,and 51904290)open fund of Key Laboratory of Safety and High-efficiency Coal Mining,Ministry of Education(Anhui University of Science and Technology)(Grant No.JYBSYS202311).
文摘Understanding the shear mechanical behaviors and instability mechanisms of rock joints under dynamic loading remains a complex challenge.This research conducts a series of direct shear tests on real rock joints subjected to cyclic normal loads to assess the influence of dynamic normal loading amplitude(F_(d)),dynamic normal loading frequency(f_(v)),initial normal loading(F_(s)),and the joint roughness coefficient(JRC)on the mechanical properties and instability responses of these joints.The results show that unstable sliding is often accompanied by friction weakening due to dynamic normal loads.A significant negative correlation exists between cyclic normal loads and the normal displacement during the shearing process.Dynamic normal load paths vary the contact states of asperities on the rough joint surfaces,impacting the stick-slip instability mechanism of the joints,which in turn affects both the magnitude and location of the stress drop during the stick-slip events,particularly during the unloading phases.An increasing F_(d) results in a more stable shearing behavior and a reduction in the amplitude of stick-slip stress drops.The variation in f_(v) influences the amplitude of stress drop for the joints during shear,characterized by an initial decrease(f_(v)=0.25-2 Hz)before exhibiting an increment(f_(v)=2-4 Hz).As F_(s) increases,sudden failures of the interlocked rough surfaces are more prone to occur,thus producing enhanced instability and a more substantial stress drop.Additionally,a larger JRC intensifies the instability of the joints,which would induce a more pronounced decline in the stick-slip stress.The Rate and state friction(RSF)law can provide an effective explanation for the unstable sliding phenomena of joints during the oscillations of normal loads.The findings may provide certain useful references for a deeper comprehension of the sliding behaviors exhibited by rock joints when subjected to cyclic dynamic disturbances.
基金supported by the National Key Research and Development Program of China(No.2021YFC3001302)the National Natural Science Foundation of China(No.52274072).
文摘Shearing dislocation is a common failure type for rock–backfill interfaces because of backfill sedimentation and rock strata movement in backfill mining goaf.This paper designed a test method for rock–backfill shearing dislocation.Using digital image techno-logy and three-dimensional(3D)laser morphology scanning techniques,a set of 3D models with rough joint surfaces was established.Further,the mechanical behavior of rock–backfill shearing dislocation was investigated using a direct shear test.The effects of interface roughness on the shear–displacement curve and failure characteristics of rock–backfill specimens were considered.The 3D fractal dimen-sion,profile line joint roughness coefficient(JRC),profile line two-dimensional fractal dimension,and the surface curvature of the frac-tures were obtained.The correlation characterization of surface roughness was then analyzed,and the shear strength could be measured and calculated using JRC.The results showed the following:there were three failure threshold value points in rock–backfill shearing dis-location:30%–50%displacement before the peak,70%–90%displacement before the peak,and 100%displacement before the peak to post-peak,which could be a sign for rock–backfill shearing dislocation failure.The surface JRC could be used to judge the rock–backfill shearing dislocation failure,including post-peak sliding,uniform variations,and gradient change,corresponding to rock–backfill disloca-tion failure on the field site.The research reveals the damage mechanism for rock–backfill complexes based on the free joint surface,fills the gap of existing shearing theoretical systems for isomerism complexes,and provides a theoretical basis for the prevention and control of possible disasters in backfill mining.
基金funded by the Environment and Conservation Fund(Grant Nos.2020-170 and 2021-156)the National Natural Science Foundation of China(Grant No.42102327).
文摘The deep cement mixing(DCM)is used to improve the capacity and reduce the settlement of the soft ground by forming cemented clay columns.The investigation on the mechanical behaviour of the DCM samples is limited to either laboratory-prepared samples or in-situ samples under unconfined compression.In this study,a series of drained and undrained triaxial shearing tests was performed on the in-situ cored DCM samples with high cement content to assess their mechanical behaviours.It is found that the drainage condition affects significantly the stiffness,peak and residual strengths of the DCM samples,which is mainly due to the state of excess pore water pressure at different strain levels,i.e.being positive before the peak deviatoric stress and negative after the peak deviatoric stress,in the undrained tests.The slope of the failure envelope changes obviously with the confining pressures,being steeper at lower stress levels and flatter at higher stress levels.The strength parameters,effective cohesion and friction angle obtained from lower stress levels(c′0 andφ′0)are 400 kPa and 58°,respectively,which are deemed to be true for design in most DCM applications where the in-situ stress levels are normally at lower values of 50-200 kPa.Additionally,the computed tomography(CT)scanning system was adopted to visualize the internal structures of DCM samples.It is found that the clay pockets existing inside the DCM samples due to uneven mixing affect markedly their stress-strain behaviour,which is one of the main reasons for the high variability of the DCM samples.
基金funded by the National Natural Science Foundation of China(Grant Nos.U22A20166 and 12172230)the Guangdong Basic and Applied Basic Research Foundation(Grant No.2023A1515012654)+1 种基金funded by the National Natural Science Foundation of China(Grant Nos.U22A20166 and 12172230)the Guangdong Basic and Applied Basic Research Foundation(Grant No.2023A1515012654)。
文摘Understanding the anisotropic creep behaviors of shale under direct shearing is a challenging issue.In this context,we conducted shear-creep and steady-creep tests on shale with five bedding orientations (i.e.0°,30°,45°,60°,and 90°),under multiple levels of direct shearing for the first time.The results show that the anisotropic creep of shale exhibits a significant stress-dependent behavior.Under a low shear stress,the creep compliance of shale increases linearly with the logarithm of time at all bedding orientations,and the increase depends on the bedding orientation and creep time.Under high shear stress conditions,the creep compliance of shale is minimal when the bedding orientation is 0°,and the steady-creep rate of shale increases significantly with increasing bedding orientations of 30°,45°,60°,and 90°.The stress-strain values corresponding to the inception of the accelerated creep stage show an increasing and then decreasing trend with the bedding orientation.A semilogarithmic model that could reflect the stress dependence of the steady-creep rate while considering the hardening and damage process is proposed.The model minimizes the deviation of the calculated steady-state creep rate from the observed value and reveals the behavior of the bedding orientation's influence on the steady-creep rate.The applicability of the five classical empirical creep models is quantitatively evaluated.It shows that the logarithmic model can well explain the experimental creep strain and creep rate,and it can accurately predict long-term shear creep deformation.Based on an improved logarithmic model,the variations in creep parameters with shear stress and bedding orientations are discussed.With abovementioned findings,a mathematical method for constructing an anisotropic shear creep model of shale is proposed,which can characterize the nonlinear dependence of the anisotropic shear creep behavior of shale on the bedding orientation.
基金support from the Natural Science Foundation of China(Grant Nos.41941018,U21A20153,42177140).
文摘The shear mechanical behavior is regarded as an essential factor affecting the stability of the surrounding rocks in underground engineering.The shear strength and failure mechanisms of layered rock are significantly affected by the foliation angles.Direct shear tests were conducted on cubic slate samples with foliation angles of 0°,30°,45°,60°,and 90°.The effect of foliation angles on failure patterns,acoustic emission(AE)characteristics,and shear strength parameters was analyzed.Based on AE characteristics,the slate failure process could be divided into four stages:quiet period,step-like increasing period,dramatic increasing period,and remission period.A new empirical expression of cohesion for layered rock was proposed,which was compared with linear and sinusoidal cohesion expressions based on the results made by this paper and previous experiments.The comparative analysis demonstrated that the new expression has better prediction ability than other expressions.The proposed empirical equation was used for direct shear simulations with the combined finite-discrete element method(FDEM),and it was found to align well with the experimental results.Considering both computational efficiency and accuracy,it was recommended to use a shear rate of 0.01 m/s for FDEM to carry out direct shear simulations.To balance the relationship between the number of elements and the simulation results in the direct shear simulations,the recommended element size is 1 mm.
基金funded by the National Natural Science Foundation of China(No.41972266)Chongqing Natural Science Foundation(No.CSTB2024NSCQ-MSX0006).
文摘Some rock joints exhibit significant brittleness,characterized by a sharp decrease in shear stress upon reaching the peak strength.However,existing models often fail to accurately represent this behavior and are encumbered by numerous parameters lacking clear mechanical significance.This study presents a new statistical damage constitutive model rooted in both damage mechanics and statistics,containing only three model parameters.The proposed model encompasses all stages of joint shearing,including the compaction stage,linear stage,plastic yielding stage,drop stage,strain softening stage,and residual strength stage.To derive the analytical expression of the constitutive model,three boundary conditions are introduced.Experimental data from both natural and artificial rock joints is utilized to validate the model,resulting in average absolute relative errors ranging from 3%to 8%.Moreover,a comparative analysis with established models illustrates that the proposed model captures stress drop and post-peak strain softening more effectively,with model parameters possessing clearer mechanical interpretations.Furthermore,parameter analysis is conducted to investigate the impacts of model parameters on the curves and unveil the relationship between these parameters and the mechanical properties of rock joints.Importantly,the proposed model is straightforward in form,and all model parameters can be obtained from direct shear tests,thus facilitating the utilization in numerical simulations.
基金Item Sponsored by National Key Basic Research Program of China (2012CB722801)
文摘Blade clearance is an important technical parameter of the shear, which determines the shear quality of plate. The finite element method was used to simulate shearing process which is in the different specifications and blade clearances, and the impact on blade section and shearing force of blade clearance was analyzed. Comparing with traditional experience formulas and measured values, the limitations of the experience formulas were proved. And by contrasting with the shearing force data collected from Linfen Iron and Steel Company, the reliability of the finite element method was further proved. The simulated results show that the simulated values controlled by ductile fracture criterion and measured values are very close, and the deviation value is in the range of 4.8%-20.8%. For the same steel, if the plate is thicker, the blade clearance will be greater, and thickness and blade clearance are approximately linear. The difference between numerical simulation of the maximum shearing force and the measured results is 7.7% to 12.0%, and the simulation results are close to facts. With the increase of blade clearance and the thickness, the shearing force was increased to some degree.
基金The authors would like to thank the National Natural Science Foundation of China and Baoshan Iron&Steel Co.of Shanghai for financial support under the grant No.50274020.
文摘The shearing/cooling roll （SCR） process was adopted to prepare semi-solid A2017 alloy. The formation and evolution of non-dendritic microstructures in semi-solid A2017 alloy were studied. It is shown that the microstructures of semi-solid billets transform from coarse dendrites into fine equiaxed grains as the pouring temperature of molten alloy decreases o.r roll-shoe cavity height is reduced. From the inlet to the exit of roll-shoe cavity, microstructure of semi-solid slurry near the shoe surface is in the order of coarse dendrites, degenerated dendrites or equiaxed grains, but fine equiaxed grains are near the roll surface. Microstructural evolution of semi-solid slurry prepared by SCR process is that the molten alloy nucleates and grows into dendrite firstly on the roll and shoe＇s surface. Under the shearing and stirring given by the rotating roll, the dendrites crush off and disperse into the melt. Under the shearing and stirring on semi-solid slurry with high volume fraction of solid, the dendrite arms fracture and form equiaxed grain microstructures.
基金supported by Liaoning Revitalization Talents Program, China (XLYC1807021)Joint Research Fund of Liaoning - Shenyang National Laboratory for Materials Science, China (2019JH3/30100014)+1 种基金Innovation Talent Program in Sciences and Technologies for Young and Middle-aged Scientists of Shenyang, China (RC200414)Scientific Research Fund of Liaoning Provincial Department of Education, China (LJGD2020008)
文摘A novel extrusion-shearing(ES) composite process was designed to fabricate fine-grained, high strength and tough magnesium alloy. The structural parameters of an ES die were optimized by conducting an orthogonal simulation experiment using finite element software Deform-3D, and Mg-3 Zn-0.6 Ca-0.6 Zr(ZXK310) alloy was processed using the ES die. The results show that the optimized structural parameters of ES die are extrusion angle(α) of 90°, extrusion section height(h) of 15 mm and inner fillet radius(r) of 10 mm. After ES at an extrusion temperature and a die temperature of 350 °C, ZXK310 alloy exhibited good ES forming ability, and obvious dynamic recrystallization occurred in the forming area. The grain size decreased from 1.42 μm of extrusion area to 0.85 μm of the forming area. Owing to the pinning of second phase and formation of ultrafine grains, the tensile strength, yield strength and elongation of alloy reached 362 MPa, 289 MPa and 21.7%, respectively.
基金Supported by the National Basic Research Program of China(No.2014CB440901)the China National Natural Science Foundation(No.41190073)the Fundamental Research Funds for the Central Universities to SYSU
文摘The Ailaoshan-Red River（ASRR） shear zone in SW China represents an important discontinuity believed to have accommodated eastward extrusion of the Tibetan Plateau in response to the collision of the Indian and Eurasian plates. The onset timing and duration of the ASRR sinistral strike-slip shearing have been hotly disputed. In this paper we present new zircon LA-ICP-MS U-Pb geochronological data from six syntectonic granitic mylonite and leucosomes samples from the ASRR shear zone. Our data reveal a metamorphic age of ~40 Ma, most likely suggesting the maximum age of the shearing initiation. Rocks showing syn-kinematic signatures yield crystallization ages of 38–22 Ma, with inherited components ranging from 716 to 108 Ma. These results, together with existing geological and geochronological data, indicate that the sinistral shearing along the ASRR zone probably began at 40 Ma, mainly activated at 29–22 Ma and lasted at least to ~22 Ma. Our data suggest a continuous extrusion between the Indochina and South China blocks during ~35–17 Ma. The ASRR sinistral shearing has accommodated large scale eastward displacement of the southeastern Tibetan syntaxis, and is likely responsible for the opening of the South China Sea.
基金The first author would like to thank the supports of the NARGS, IRGS and AAS grants of Australia, and the National Science Foundation grants （No. 51574060 and No. 51079017） of China, in which the first author is the intemational collaborator. The academic visits of the third and fourth authors to the University of Tasmania are partly supported by a PhD visiting scholarship and an academic visiting scholarship, respectively, provided by the China Scholarship Council, which are greatly appreciated.
文摘A hybrid finite-discrete element method was implemented to study the fracture process of rough rock joints under direct shearing. The hybrid method reproduced the joint shear resistance evolution process from asperity sliding to degradation and from gouge formation to grinding. It is found that, in the direct shear test of rough rock joints under constant normal displacement loading conditions, higher shearing rate promotes the asperity degradation but constraints the volume dilation, which then results in higher peak shear resistance, more gouge formation and grinding, and smoother new joint surfaces. Moreover, it is found that the joint roughness affects the joint shear resistance evolution through influencing the joint fracture micro mechanism. The asperity degradation and gouge grinding are the main failure micro-mechanism in shearing rougher rock joints with deeper asperities while the asperity sliding is the main failure micro-mechanism in shearing smoother rock joints with shallower asperities. It is concluded that the hybrid finite-discrete element method is a valuable numerical tool better than traditional finite element method and discrete element method for modelling the joint sliding, asperity degradation, gouge formation, and gouge grinding occurred in the direct shear tests of rough rock joints.
基金supported by Hebei Provincial Natural Science Foundation of China (Grant No. A2011210033)Foundation of Hebei Provincial Education Department of China (Grant No. ZH2011116)Hebei Provincial Research Program for Higher Education and Teaching Reform of China (Grant No. 103024)
文摘The existing investigations on piezoelectric materials containing an elliptic hole mainly focus on remote uniform tensile loads. In order to have a better understanding of the fracture behavior of piezoelectric materials under different loading conditions, theoretical and numerical solutions are presented for an elliptic hole in transversely isotropic piezoelectric materials subjected to uniform internal shearing forces based on the complex potential approach. By solving ten variable linear equations, the analytical solutions inside and outside the hole satisfying the permeable electric boundary conditions are obtained. Taking PZT-4 ceramic into consideration, numerical results of electro-elastic fields along the edge of the hole and axes, and the electric displacements in the hole are presented. Comparison with stresses in transverse isotropic elastic materials shows that the hoop stress at the ends of major axis in two kinds of material equals zero for the various ratios of major to minor axis lengths; If the ratio is greater than 1, the hoop stress in piezoelectric materials is smaller than that in elastic materials, and if the ratio is smaller than 1, the hoop stress in piezoelectric materials is greater than that in elastic materials; When it is a circle hole, the shearing stress in two materials along axes is the same. The distribution of electric displacement components shows that the vertical electric displacement in the hole and along axes in the material is always zero though under the permeable electric boundary condition; The horizontal and vertical electric displacement components along the edge of the hole are symmetrical and antisymmetrical about horizontal axis, respectively. The stress and electric displacement distribution tends to zero at distances far from the elliptical hole, which conforms to the conclusion usually made on the basis of Saint-Venant’s principle. Unlike the existing work, uniform shearing forces acting on the edge of the hole, and the distribution of electro-elastic fields inside and outside the elliptic hole are considered.
基金This work was financially supported by the National Natural Science Foundation of China (No.50604007)the Natural ScienceFoundation of Liaoning Province, China (No.20062016)
文摘A self-designed setup of modified sloping cooling/shearing process was made to prepare the semisolid Al-3wt%Mg alloy. A three-dimensional simulation model was established for the analysis of preparing the semisolid Al-3wt%Mg alloy. Through simulation and experiment, it is shown that the sloping angle of the plate greatly affects temperature and velocity distributions, and the temperature and velocity of the alloy at the exit of the sloping plate increase with the increase of the sloping angle. The alloy temperature decreases linearly from the pouring mouth to the exit. The alloy temperature at the exit increases obviously with the increase of pouring temperature. To prepare the semisolid Al-3wt%Mg alloy with good quality, the sloping angle θ=45° is reasonable, and the pouring temperature is suggested to be designed above 650-660℃ but under 700℃.
基金Projects(51275201,51311130129)supported by the National Natural Science of ChinaProject(20140204062GX)supported by the Jilin Key Scientific and Technological Project,China
文摘Punch shearing is used to form the part in the material process.Cryogenic treatment(CT)has active effect on local mechanical properties of steel,but it is still uncertain of the influence of CT on the properties of the magnesium alloy during punch shearing.In this work,the influence of AZ31 sheet treated by cryogenic on punch shearing was studied.Microstructures were observed with a ZEISS optical microscope,and mechanical properties,as well as shear properties were tested by tensile testing and punch shearing.The results show that the number of secondary phase increases and a large number of twins appear in the grains after CT.Meanwhile,the ultimate tensile strength(UTS),the ductility,and hardness of AZ31 are improved,while the yield strength(YS)decreases gradually during CT.During punch shearing,the shearing strength decreases,the rollover radius changes insignificantly,and the height of the burr on the edge of the cross section decreases.At the same time,a larger proportion of smooth zone on the cross section has been achieved.
