To investigate the influence of coarse aggregate parent rock properties on the elastic modulus of concrete,the mineralogical properties and stress-strain curves of granite and dolomite parent rocks,as well as the stre...To investigate the influence of coarse aggregate parent rock properties on the elastic modulus of concrete,the mineralogical properties and stress-strain curves of granite and dolomite parent rocks,as well as the strength and elastic modulus of mortar and concrete prepared with mechanism aggregates of the corresponding lithology,and the stress-strain curves of concrete were investigated.In this paper,a coarse aggregate and mortar matrix bonding assumption is proposed,and a prediction model for the elastic modulus of mortar is established by considering the lithology of the mechanism sand and the slurry components.An equivalent coarse aggregate elastic modulus model was established by considering factors such as coarse aggregate particle size,volume fraction,and mortar thickness between coarse aggregates.Based on the elastic modulus of the equivalent coarse aggregate and the remaining mortar,a prediction model for the elastic modulus of the two and three components of concrete in series and then in parallel was established,and the predicted values differed from the measured values within 10%.It is proposed that the coarse aggregate elastic modulus in highstrength concrete is the most critical factor affecting the elastic modulus of concrete,and as the coarse aggregate elastic modulus increases by 27.7%,the concrete elastic modulus increases by 19.5%.展开更多
Hard tissue repair materials that balance high strength with low modulus are highly promising,representing a transformative focus in applied biomaterials research.In this study,Ti-Nb alloys with high performance are p...Hard tissue repair materials that balance high strength with low modulus are highly promising,representing a transformative focus in applied biomaterials research.In this study,Ti-Nb alloys with high performance are prepared by a low-cost process for orthopedic applications.Phase composition,modulus,compressive strength and recovery properties are effectively manipulated by tailoring trace amounts of interstitial oxygen.With increasing oxygen concentration in sintered Ti-Nb alloys,theβ(body centered cubic)phase was stabilized due to the lattice distortion.The elastic modulus declined from 91 to 24 GPa.The compressive strength slightly decreased from 1595 to 1404 MPa and yield strength increased from 760 to 904 MPa.Additionally,the recovery properties were enhanced by the interstitial oxygen as a shape memory alloy.The utilization of trace oxygen serves to modulate the thermoelastic martensitic transformation in Ti-Nb alloys,thereby obtaining appropriate mechanical properties.A notable reduction in modulus is achieved while maintaining high strength,which facilitates the development of orthopedic implants capable of withstanding more complex forces.展开更多
Alkali-free SiO_(2)-Al_(2)O_(3)-CaO-MgO with different SiO_(2)/Al_(2)O_(3)mass ratios was prepared by conventional melt quenching method.The glass network structure,thermodynamic properties and elastic modulus changes...Alkali-free SiO_(2)-Al_(2)O_(3)-CaO-MgO with different SiO_(2)/Al_(2)O_(3)mass ratios was prepared by conventional melt quenching method.The glass network structure,thermodynamic properties and elastic modulus changes with SiO_(2)and Al_(2)O_(3)ratios were investigated using various techniques.It is found that when SiO_(2)is replaced by Al_(2)O_(3),the Q^(4) to Q^(3) transition of silicon-oxygen network decreases while the aluminum-oxygen network increases,which result in the transformation of Si-O-Si bonds to Si-O-Al bonds and an increase in glass network connectivity even though the intermolecular bond strength decreases.The glass transition temperature(T_(g))increases continuously,while the thermal expansion coefficient increases and high-temperature viscosity first decreases and then increases.Meanwhile,the elastic modulus values increase from 93 to 102 GPa.This indicates that the elastic modulus is mainly affected by packing factor and dissociation energy,and elements with higher packing factors and dissociation energies supplant those with lower values,resulting in increased rigidity within the glass.展开更多
This study investigates the width of the secondary eyewall(SE)immediately following its formation in tropical cyclones with surface environmental winds aligned and counter-aligned with environmental vertical wind shea...This study investigates the width of the secondary eyewall(SE)immediately following its formation in tropical cyclones with surface environmental winds aligned and counter-aligned with environmental vertical wind shear(VWS),using idealized numerical experiments.Results reveal that the SE develops greater radial extent when surface winds align with VWS compared to counter-aligned conditions.In alignment configurations,shear-enhanced surface winds on the right flank amplify surface enthalpy fluxes,thereby elevating boundary-layer entropy within the downshear outer-core region.Subsequently,more vigorous outer rainbands develop,inducing marked acceleration of tangential winds in the outer core preceding SE formation.The resultant radial expansion of supergradient winds near the boundary-layer top triggers widespread convective activity immediately beyond the inner core.Progressive axisymmetrization of this convective forcing ultimately generates an expansive SE structure.展开更多
The yielding transition of amorphous solids remains a fundamental yet poorly understood issue in materials physics.In this work,we employ oscillatory shear to probe the yielding transition in metallic glasses(MGs)with...The yielding transition of amorphous solids remains a fundamental yet poorly understood issue in materials physics.In this work,we employ oscillatory shear to probe the yielding transition in metallic glasses(MGs)with various thermal histories.We identify three distinct deformation regimes depending on the applied strain amplitudes.Below the yield strainγ_(y),the response is elastic and accompanied by aging,through reversible atomic rearrangements that preserve the material's initial memory of thermal history.Slightly aboveγ_(y),the system undergoes a sharp transition during oscillatory cycles,indicated by a sudden rise in potential energy and non-affine displacement,along with the emergence of a shear band.Well aboveγ_(y),plastic deformation dominates,driving samples of various initial stability toward a common steady state,while thermal histories are erased by irreversible rearrangements and shear band formation.These findings advance the understanding of failure mechanisms in MGs and shed light on tuning their mechanical performance in industrial applications involving cyclic loading.展开更多
Rock mass stability is significantly influenced by the heterogeneity of rock joint roughness and shear strength.While modern technology facilitates assessing roughness heterogeneity,evaluating shear strength heterogen...Rock mass stability is significantly influenced by the heterogeneity of rock joint roughness and shear strength.While modern technology facilitates assessing roughness heterogeneity,evaluating shear strength heterogeneity remains challenging.To address this,this study first captures the morphology of large-scale(1000 mm × 1000 mm) slate and granite joints via 3D laser scanning.Analysis of these surfaces and corresponding push/pull tests on carved specimens revealed a potential correlation between the heterogeneity of roughness and shear strength.A comparative evaluation of five statistical metrics identified information entropy(Hs) as the most robust indicator for quantifying rock joint heterogeneity.Further analysis using Hsreveals that the heterogeneity is anisotropic and,critically,that shear strength heterogeneity is governed not only by roughness heterogeneity but is also significantly influenced by the mean roughness value,normal stress,and intact rock tensile strength.Consequently,a simple comparison of roughness Hsvalues is insufficient for reliably comparing shear strength heterogeneity.To overcome this limitation,a theoretical framework is developed to explicitly map fundamental roughness statistics(mean and heterogeneity) to shear strength heterogeneity.This framework culminates in a practical workflow that allows for the rapid,field-based assessment of shear strength heterogeneity using readily obtainable rock joint roughness data.展开更多
Based on the magnetic interaction energy, using derivative of the magnetic energy density, a model is proposed to compute the magnetic-induced shear modulus of magnetorheological elastomers. Taking into account the in...Based on the magnetic interaction energy, using derivative of the magnetic energy density, a model is proposed to compute the magnetic-induced shear modulus of magnetorheological elastomers. Taking into account the influences of particles in the same chain and the particles in all adjacent chains, the traditional magnetic dipole model of the magnetorheological elastomers is modified. The influence of the ratio of the distance etween adjacent chains to the distance between adjacent particles in a chain on the magnetic induced shear odulus is quantitatively studied. When the ratio is large, the multi-chain model is compatible with the single chain model, but when the ratio is small, the difference of the two models is significant and can not be neglected. Making certain the size of the columns and the distance between adjacent columns, after constructing the computational model of BCT structures, the mechanical property of the magnetorheological elastomers composed of columnar structures is analyzed. Results show that, conventional point dipole model has overrated the magnetic-induced shear modulus of the magnetorheological elastomers. From the point of increasing the magnetic-induced shear modulus, when the particle volume fraction is small, the chain-like structure exhibits better result than the columnar structure, but when the particle volume fraction is large,the columnar structure will be better.展开更多
Recycled waste tires when mixed with soil can play an important role as lightweight materials in retaining walls and embankments, machine foundations and railroad track beds in seismic zones. Having high damping chara...Recycled waste tires when mixed with soil can play an important role as lightweight materials in retaining walls and embankments, machine foundations and railroad track beds in seismic zones. Having high damping characteristic, rubbers can be used as either soil alternative or mixed with soil to reduce vibration when seismic loads are of great concern. Therefore, the objective of this work was to evaluate the dynamic properties of such mixtures prior to practical applications. To this reason, torsional resonant column and dynamic triaxial experiments were carried out and the effect of the important parameters like rubber content and ratio of mean grain size of rubber solids versus soil solids(D50,r/D50,s) on dynamic response of mixtures in a range of low to high shearing strain amplitude from about 4×10-4% to 2.7% were investigated. Considering engineering applications, specimens were prepared almost at the maximum dry density and optimum moisture content to model a mixture layer above the ground water table and in low precipitation region. The results show that tire inclusion significantly reduces the shear modulus and increases the damping ratio of the mixtures. Also decrease in D50,r/D50,s causes the mixture to exhibit more rubber-like behavior. Finally, normalized shear modulus versus shearing strain amplitude curve was proposed for engineering practice.展开更多
This paper presents results from a series of stress-controlled undrained cyclic triaxial tests on the undisturbed marine silty clay,silt,and fine sand soils obtained from the Bohai Sea,China.Emphasis is placed on the ...This paper presents results from a series of stress-controlled undrained cyclic triaxial tests on the undisturbed marine silty clay,silt,and fine sand soils obtained from the Bohai Sea,China.Emphasis is placed on the major factors for predominating the dynamic shear modulus(G)and damping ratio(λ)in the shear strain amplitude(γ_(a))from 10^(-5) to 10^(-2),involving depth,sedimentary facies types,and water content of marine soils.The empirical equations of the small-strain shear modulus(G_(max))and damping ratio(λ_(min))using a single-variable of depth H are established for the three marine soils.A remarkable finding is that the curves of shear modulus reduction(G/G_(max))and the damping ratio(λ)with increasing γ_(a) of the three marine soils can be simply determined through a set of explicit expressions with the two variables of depth H and water content W.This finding is validated by independent experimental data from the literature.At the similar depths,the G value of the marine soils of terrestrial facies is the largest,followed b_(y) the neritic facies,and the G value of the marine soils of abyssal facies is the smallest.The sedimentary facies types of the marine soils have slight effect on theλvalue.Another significant finding is that the shear modulus reduction curves plotted against the γ_(a) of the three marine soils at the similar depths are significantly below those of the corresponding terrigenous soils,while the damping curves plotted against γ_(a) are just the opposite.The results presented in this paper serve as a worthful reference for the evaluation of seabed seismic site effects in the Bohai Sea due to lack of experimental data.展开更多
The dynamic shear modulus for three types of undisturbed soil under different consolidation ratios is presented by using the resonant column test method. Its effects on surface ground motion is illustrated by calculat...The dynamic shear modulus for three types of undisturbed soil under different consolidation ratios is presented by using the resonant column test method. Its effects on surface ground motion is illustrated by calculation. The test results indicate that the power function is a suitable form for describing the relationship between the ratio of the maximum dynamic shear modulus due to anisotropic and isotropic consolidations and the increment of the consolidation ratio. When compared to sand, the increment of the maximum dynamic shear modulus for undisturbed soil due to anisotropic consolidation is much larger. Using a one-dimensional equivalent linearization method, the earthquake influence factor and the characteristic period of the surface acceleration are calculated for two soil layers subjected to several typical earthquake waves. The calculated results show that the difference in nonlinear properties due to different consolidation ratios is generally not very notable, but the degree of its influence on the surface acceleration spectrum is remarkable for the occurrence of strong earthquakes. When compared to isotropic consolidation, the consideration of actual anisotropic consolidation causes the characteristic period to decrease and the earthquake influence factor to increase.展开更多
Evaluation of the cyclic shear modulus of soils is a crucial but challenging task for many geotechnical earthquake engineering and soil dynamic issues. Improper determination of this property unnecessarily drives up d...Evaluation of the cyclic shear modulus of soils is a crucial but challenging task for many geotechnical earthquake engineering and soil dynamic issues. Improper determination of this property unnecessarily drives up design and maintenance costs or even leads to the construction of unsafe structures. Due to the complexities involved in the direct measurement, empirical curves for estimating the cyclic shear modulus have been commonly adopted in practice for simplicity and economical considerations. However, a systematic and robust approach for formulating a reliable model and empirical curve for cyclic shear modulus prediction for clayey soils is still lacking. In this study, the Bayesian model class selection approach is utilized to identify the most significant soil parameters affecting the normalized cyclic shear modulus and a reliable predictive model for normally to moderately over-consolidated clays is proposed. Results show that the predictability and reliability of the proposed model out performs the well-known empirical models. Finally, a new design chart is established for practical usage.展开更多
A relationship between thermal effects and relaxation of the high-frequency shear modulus upon heat treatment of bulk Zr48(Cu5/6Ag1/6)44Al8 metallic glass is found.This relationship is attributed to the relaxation of ...A relationship between thermal effects and relaxation of the high-frequency shear modulus upon heat treatment of bulk Zr48(Cu5/6Ag1/6)44Al8 metallic glass is found.This relationship is attributed to the relaxation of a interstitial-type defect system frozen-in from the melt upon glass production.Calorimetric data show that thermal effects occurring on heating include heat release below the glass transition temperature,heat absorption above it and heat release caused by crystallization.The equation derived within the Interstitialcy theory can be used to calculate the shear modulus relaxation using the calorimetric data.The obtained results are used to trace the defect concentration as functions of temperature and thermal prehistory.展开更多
Asymmetric plate impact experiments are conducted on LY12 aluminium alloy in a pressure range of 85-131 GPa. The longitudinal sound speeds axe obtained from the time-resolved particle speed profiles of the specimen me...Asymmetric plate impact experiments are conducted on LY12 aluminium alloy in a pressure range of 85-131 GPa. The longitudinal sound speeds axe obtained from the time-resolved particle speed profiles of the specimen measured with Velocity Interferometer System for Any Reflector （VISAR） technique, and they are shown to be good agreement with our previously reported data of this alloy in a pressure range of 20-70 GPa, and also with those of 2024 aluminium reported by McQueen. Using all of the longitudinal speeds and the corresponding bulk speeds calculated from the Gruneisen equation of state （EOS）, shear moduli of LY12 aluminium alloy are obtained. A comparison of the shear moduli in the solid phase region with those estimated from the Steinberg model demonstrate that the latter are systematically lower than the measurements. By re-analysing the pressure effect on the shear modulus, a modified equation is proposed, in which the pressure term of P/η^1/3 in the Steinberg model is replaced by a linear term. Good agreement between experiments and the modified equation is obtained, which implies that the shear modulus of LY12 aluminium varies linearly both with pressure and with temperature throughout the whole solid phase region. On the other hand, shear modulus of aluminium in a solid-liquid mixed phrase region decreases gradually and smoothly, a feature that is very different from the drastic dropping at the melting point under static conditions.展开更多
A plane strain analysis based on the generalized Biot＇s equation is utilized to investigate the wave-induced response of a poro-elastic seabed with variable shear modulus. By employing integral transform and Frobenin...A plane strain analysis based on the generalized Biot＇s equation is utilized to investigate the wave-induced response of a poro-elastic seabed with variable shear modulus. By employing integral transform and Frobenins methods, the transient and steady solutions for the wave-inducod pore water pressure, effective stresses and displacements are analytically derived in detail. Verification is available through the reduction to the simple case of homogeneous seabed. The numerical results indicate that the inclusion of variable shear modulus significantly affects the wave-induced seabed response.展开更多
The fabric anisotropy of a granular soil deposit can strongly infl uence its engineering properties and behavior. This paper presents the results of a novel experimental study designed to examine the effects of fabric...The fabric anisotropy of a granular soil deposit can strongly infl uence its engineering properties and behavior. This paper presents the results of a novel experimental study designed to examine the effects of fabric anisotropy on smallstrain stiffness and its evolution with loading on the elastic shear modulus of granular materials under a K0 condition. Two primary categories of fabric anisotropy, i.e., deposition-induced and particle shape-induced, are investigated. Toyoura sand deposits with relative densities of 40% and 80% were prepared using deposition angles oriented at 0o and 90o. Piezoelectric transducers were used to obtain the elastic shear modulus in the vertical and horizontal directions(Gvh and Ghh). The measurements indicate distinct differences in the values of G with respect to the different deposition angles. Particle shapeinduced fabric anisotropy was examined using four selected sands. It was concluded that sphericity is a controlling factor dominating the small-strain stiffness of granular materials. The degree of fabric anisotropy proves to be a good indicatorin the characterization of stress-induced fabric evolution during loading and unloading stress cycles. The experimental data were used to calibrate an existing micromechanical model, which was able to represent the behavior of the granular material and the degree of fabric anisotropy reasonably well.展开更多
High-pressure Raman scattering from hexagonal close-packed(HCP) metals Os and Re have been extended up to 200 GPa, and the pressure-dependent shear modulus C_(44)has been deduced from the Raman-active mode E_(28), whi...High-pressure Raman scattering from hexagonal close-packed(HCP) metals Os and Re have been extended up to 200 GPa, and the pressure-dependent shear modulus C_(44)has been deduced from the Raman-active mode E_(28), which is generated from the adjacent vibration of atoms in hexagonal planes, providing the valuable information about the elastic properties for HCP metals under high pressure. Combined with the available data of HCP metals from previous works,a further study indicates that the C_(44)/C_(44)ratio would be close to a constant value, 0.01, with increasing atomic number of metals. The results obtained from high-pressure Raman scattering will allow us to probe the elastic anisotropy of the HCP metals at very high pressure.展开更多
An error analysis of the dynamic shear modulus of stiff specimens from tests performed by a new resonant column device developed by the Institute of Engineering Mechanics, China was conducted. A modified approach for ...An error analysis of the dynamic shear modulus of stiff specimens from tests performed by a new resonant column device developed by the Institute of Engineering Mechanics, China was conducted. A modified approach for calculating the dynamic shear modulus of the stiff specimens is presented. The error formula of the tests was deduced and parameters that impact the accuracy of the test were identified. Using six steel specimens with known standard stiffness as a base, a revised dynamic shear modulus calculation for stiff specimens was formulated by comparing three of the models. The maximum error between the test results and the calculated results shown by curves from both the free-vibration and the resonant-vibration tests is less than 6%. The free-vibration and resonant-vibration tests for three types of stiff samples with a known modulus indicate that the maximum deviation between the actual and the tested value using the modified approach were less than 10%. As a result, the modified approach presented here is shown to be reliable and the new device can be used for testing dynamic shear modulus of any stiff materials at low shear strain levels展开更多
The dynamic shear modulus (DSM) is the most basic soil parameter in earthquake or other dynamic loading conditions and can be obtained through testing in the field or in the laboratory. The effect of consolidation rat...The dynamic shear modulus (DSM) is the most basic soil parameter in earthquake or other dynamic loading conditions and can be obtained through testing in the field or in the laboratory. The effect of consolidation ratios on the maximum DSM for two types of sand is investigated by using resonant column tests. And, an increment formula to obtain the maximum DSM for cases of consolidation ratio κc>1 is presented. The results indicate that the maximum DSM rises rapidly when κc is near 1 and then slows down, which means that the power function of the consolidation ratio increment κc-1 can be used to describe the variation of the maximum DSM due to κc>1. The results also indicate that the increase in the maximum DSM due to κc>1 is significantly larger than that predicted by Hardin and Black's formula.展开更多
Effects of the tempering temperature and time on the shear modulus of Fe-Mn based alloys have been studied.The results show that(ΔG/G)-Tcurves of tempered alloys containing Cr and Ti have two extreme values—maximum ...Effects of the tempering temperature and time on the shear modulus of Fe-Mn based alloys have been studied.The results show that(ΔG/G)-Tcurves of tempered alloys containing Cr and Ti have two extreme values—maximum and minimum,and that the curves of tem- pered alloys containing Cr,Ni,W and C only have a maximum value.This is the reason that Ni,W and C decrease the transformation point T_N of the antiferromagnetism.The ΔG_λ ef- feet increases gradually with the rise of tempering temperature or with the increase of tem- pering time.展开更多
To solve the problems of divergence,low accuracy and project application of membrane wrinkling analysis,an analysis method of zero shear modulus and equivalent stiffness was proposed.This method is an improvement to t...To solve the problems of divergence,low accuracy and project application of membrane wrinkling analysis,an analysis method of zero shear modulus and equivalent stiffness was proposed.This method is an improvement to the previous method (Method I) of local coordinate transposition and stiffness equivalence.The new method is derived and the feasibility is theoretically proved.A small-scale membrane structure is analyzed by the two methods,and the results show that the computational efficiency of the new method (Method II) is approximately 23 times that of Method I.When Method II is applied to a large-scale membrane stadium structure,it is found that this new method can quickly make the second principal stress of one way wrinkled elements zero,and make the two principal stresses of two-way wrinkled elements zero as well.It could attain the correct load responses right after the appearance of wrinkled elements,which indicates that Method II can be applied to wrinkling analysis of large-scale membrane structures.展开更多
基金Funded by State Railway Administration Research Project(No.2023JS007)National Natural Science Foundation of China(No.52438002)+1 种基金Research and Development Programs for Science and Technology of China Railways Corporation(No.J2023G003)New Cornerstone Science Foundation through the XPLORER PRIZE。
文摘To investigate the influence of coarse aggregate parent rock properties on the elastic modulus of concrete,the mineralogical properties and stress-strain curves of granite and dolomite parent rocks,as well as the strength and elastic modulus of mortar and concrete prepared with mechanism aggregates of the corresponding lithology,and the stress-strain curves of concrete were investigated.In this paper,a coarse aggregate and mortar matrix bonding assumption is proposed,and a prediction model for the elastic modulus of mortar is established by considering the lithology of the mechanism sand and the slurry components.An equivalent coarse aggregate elastic modulus model was established by considering factors such as coarse aggregate particle size,volume fraction,and mortar thickness between coarse aggregates.Based on the elastic modulus of the equivalent coarse aggregate and the remaining mortar,a prediction model for the elastic modulus of the two and three components of concrete in series and then in parallel was established,and the predicted values differed from the measured values within 10%.It is proposed that the coarse aggregate elastic modulus in highstrength concrete is the most critical factor affecting the elastic modulus of concrete,and as the coarse aggregate elastic modulus increases by 27.7%,the concrete elastic modulus increases by 19.5%.
基金Project(52501069)supported by the National Natural Science Foundation of ChinaProject(GZC20233172)supported by the Postdoctoral Fellowship Program of China Postdoctoral Science Foundation(CPSF)Project(21B0121)supported by Hunan Provincial Education Department,China。
文摘Hard tissue repair materials that balance high strength with low modulus are highly promising,representing a transformative focus in applied biomaterials research.In this study,Ti-Nb alloys with high performance are prepared by a low-cost process for orthopedic applications.Phase composition,modulus,compressive strength and recovery properties are effectively manipulated by tailoring trace amounts of interstitial oxygen.With increasing oxygen concentration in sintered Ti-Nb alloys,theβ(body centered cubic)phase was stabilized due to the lattice distortion.The elastic modulus declined from 91 to 24 GPa.The compressive strength slightly decreased from 1595 to 1404 MPa and yield strength increased from 760 to 904 MPa.Additionally,the recovery properties were enhanced by the interstitial oxygen as a shape memory alloy.The utilization of trace oxygen serves to modulate the thermoelastic martensitic transformation in Ti-Nb alloys,thereby obtaining appropriate mechanical properties.A notable reduction in modulus is achieved while maintaining high strength,which facilitates the development of orthopedic implants capable of withstanding more complex forces.
基金Supported by the National Key Research Program(No.2024-1129-954-112)National Natural Science Foundation of China(No.52372033)Guangxi Science and Technology Major Program(No.AA24263054)。
文摘Alkali-free SiO_(2)-Al_(2)O_(3)-CaO-MgO with different SiO_(2)/Al_(2)O_(3)mass ratios was prepared by conventional melt quenching method.The glass network structure,thermodynamic properties and elastic modulus changes with SiO_(2)and Al_(2)O_(3)ratios were investigated using various techniques.It is found that when SiO_(2)is replaced by Al_(2)O_(3),the Q^(4) to Q^(3) transition of silicon-oxygen network decreases while the aluminum-oxygen network increases,which result in the transformation of Si-O-Si bonds to Si-O-Al bonds and an increase in glass network connectivity even though the intermolecular bond strength decreases.The glass transition temperature(T_(g))increases continuously,while the thermal expansion coefficient increases and high-temperature viscosity first decreases and then increases.Meanwhile,the elastic modulus values increase from 93 to 102 GPa.This indicates that the elastic modulus is mainly affected by packing factor and dissociation energy,and elements with higher packing factors and dissociation energies supplant those with lower values,resulting in increased rigidity within the glass.
基金jointly supported by the National Natural Science Foundation of China[grant numbers U2342202,42175005,and 42175016]the Qing Lan Project[grant number R2023Q06]。
文摘This study investigates the width of the secondary eyewall(SE)immediately following its formation in tropical cyclones with surface environmental winds aligned and counter-aligned with environmental vertical wind shear(VWS),using idealized numerical experiments.Results reveal that the SE develops greater radial extent when surface winds align with VWS compared to counter-aligned conditions.In alignment configurations,shear-enhanced surface winds on the right flank amplify surface enthalpy fluxes,thereby elevating boundary-layer entropy within the downshear outer-core region.Subsequently,more vigorous outer rainbands develop,inducing marked acceleration of tangential winds in the outer core preceding SE formation.The resultant radial expansion of supergradient winds near the boundary-layer top triggers widespread convective activity immediately beyond the inner core.Progressive axisymmetrization of this convective forcing ultimately generates an expansive SE structure.
基金supported by the National Natural Science Foundation of China(Grant Nos.52201169 and 52575352)the Key Research&Development Plan of Anhui Province(Grant No.2022a05020016)。
文摘The yielding transition of amorphous solids remains a fundamental yet poorly understood issue in materials physics.In this work,we employ oscillatory shear to probe the yielding transition in metallic glasses(MGs)with various thermal histories.We identify three distinct deformation regimes depending on the applied strain amplitudes.Below the yield strainγ_(y),the response is elastic and accompanied by aging,through reversible atomic rearrangements that preserve the material's initial memory of thermal history.Slightly aboveγ_(y),the system undergoes a sharp transition during oscillatory cycles,indicated by a sudden rise in potential energy and non-affine displacement,along with the emergence of a shear band.Well aboveγ_(y),plastic deformation dominates,driving samples of various initial stability toward a common steady state,while thermal histories are erased by irreversible rearrangements and shear band formation.These findings advance the understanding of failure mechanisms in MGs and shed light on tuning their mechanical performance in industrial applications involving cyclic loading.
基金supported by the National Natural Science Foundation of China (Nos.42422705,42207175,42177117 and 42577170)the Ningbo Youth Leading Talent Project (No.2024QL051)+1 种基金the Chinese Academy of Engineering Science and Technology Strategy Consulting Project (No.2025-XZ-57)the Central Government Funding Program for Guiding Local Science and Technology Development (No.2025ZY01028)。
文摘Rock mass stability is significantly influenced by the heterogeneity of rock joint roughness and shear strength.While modern technology facilitates assessing roughness heterogeneity,evaluating shear strength heterogeneity remains challenging.To address this,this study first captures the morphology of large-scale(1000 mm × 1000 mm) slate and granite joints via 3D laser scanning.Analysis of these surfaces and corresponding push/pull tests on carved specimens revealed a potential correlation between the heterogeneity of roughness and shear strength.A comparative evaluation of five statistical metrics identified information entropy(Hs) as the most robust indicator for quantifying rock joint heterogeneity.Further analysis using Hsreveals that the heterogeneity is anisotropic and,critically,that shear strength heterogeneity is governed not only by roughness heterogeneity but is also significantly influenced by the mean roughness value,normal stress,and intact rock tensile strength.Consequently,a simple comparison of roughness Hsvalues is insufficient for reliably comparing shear strength heterogeneity.To overcome this limitation,a theoretical framework is developed to explicitly map fundamental roughness statistics(mean and heterogeneity) to shear strength heterogeneity.This framework culminates in a practical workflow that allows for the rapid,field-based assessment of shear strength heterogeneity using readily obtainable rock joint roughness data.
文摘Based on the magnetic interaction energy, using derivative of the magnetic energy density, a model is proposed to compute the magnetic-induced shear modulus of magnetorheological elastomers. Taking into account the influences of particles in the same chain and the particles in all adjacent chains, the traditional magnetic dipole model of the magnetorheological elastomers is modified. The influence of the ratio of the distance etween adjacent chains to the distance between adjacent particles in a chain on the magnetic induced shear odulus is quantitatively studied. When the ratio is large, the multi-chain model is compatible with the single chain model, but when the ratio is small, the difference of the two models is significant and can not be neglected. Making certain the size of the columns and the distance between adjacent columns, after constructing the computational model of BCT structures, the mechanical property of the magnetorheological elastomers composed of columnar structures is analyzed. Results show that, conventional point dipole model has overrated the magnetic-induced shear modulus of the magnetorheological elastomers. From the point of increasing the magnetic-induced shear modulus, when the particle volume fraction is small, the chain-like structure exhibits better result than the columnar structure, but when the particle volume fraction is large,the columnar structure will be better.
文摘Recycled waste tires when mixed with soil can play an important role as lightweight materials in retaining walls and embankments, machine foundations and railroad track beds in seismic zones. Having high damping characteristic, rubbers can be used as either soil alternative or mixed with soil to reduce vibration when seismic loads are of great concern. Therefore, the objective of this work was to evaluate the dynamic properties of such mixtures prior to practical applications. To this reason, torsional resonant column and dynamic triaxial experiments were carried out and the effect of the important parameters like rubber content and ratio of mean grain size of rubber solids versus soil solids(D50,r/D50,s) on dynamic response of mixtures in a range of low to high shearing strain amplitude from about 4×10-4% to 2.7% were investigated. Considering engineering applications, specimens were prepared almost at the maximum dry density and optimum moisture content to model a mixture layer above the ground water table and in low precipitation region. The results show that tire inclusion significantly reduces the shear modulus and increases the damping ratio of the mixtures. Also decrease in D50,r/D50,s causes the mixture to exhibit more rubber-like behavior. Finally, normalized shear modulus versus shearing strain amplitude curve was proposed for engineering practice.
基金National Natural Science Foundation of China under Grant Nos.51978334 and 51978335。
文摘This paper presents results from a series of stress-controlled undrained cyclic triaxial tests on the undisturbed marine silty clay,silt,and fine sand soils obtained from the Bohai Sea,China.Emphasis is placed on the major factors for predominating the dynamic shear modulus(G)and damping ratio(λ)in the shear strain amplitude(γ_(a))from 10^(-5) to 10^(-2),involving depth,sedimentary facies types,and water content of marine soils.The empirical equations of the small-strain shear modulus(G_(max))and damping ratio(λ_(min))using a single-variable of depth H are established for the three marine soils.A remarkable finding is that the curves of shear modulus reduction(G/G_(max))and the damping ratio(λ)with increasing γ_(a) of the three marine soils can be simply determined through a set of explicit expressions with the two variables of depth H and water content W.This finding is validated by independent experimental data from the literature.At the similar depths,the G value of the marine soils of terrestrial facies is the largest,followed b_(y) the neritic facies,and the G value of the marine soils of abyssal facies is the smallest.The sedimentary facies types of the marine soils have slight effect on theλvalue.Another significant finding is that the shear modulus reduction curves plotted against the γ_(a) of the three marine soils at the similar depths are significantly below those of the corresponding terrigenous soils,while the damping curves plotted against γ_(a) are just the opposite.The results presented in this paper serve as a worthful reference for the evaluation of seabed seismic site effects in the Bohai Sea due to lack of experimental data.
基金National Natural Science Foundation of China under Grant No.51108163Natural Science Foundation of Heilongjiang Province under Grant No.E201104
文摘The dynamic shear modulus for three types of undisturbed soil under different consolidation ratios is presented by using the resonant column test method. Its effects on surface ground motion is illustrated by calculation. The test results indicate that the power function is a suitable form for describing the relationship between the ratio of the maximum dynamic shear modulus due to anisotropic and isotropic consolidations and the increment of the consolidation ratio. When compared to sand, the increment of the maximum dynamic shear modulus for undisturbed soil due to anisotropic consolidation is much larger. Using a one-dimensional equivalent linearization method, the earthquake influence factor and the characteristic period of the surface acceleration are calculated for two soil layers subjected to several typical earthquake waves. The calculated results show that the difference in nonlinear properties due to different consolidation ratios is generally not very notable, but the degree of its influence on the surface acceleration spectrum is remarkable for the occurrence of strong earthquakes. When compared to isotropic consolidation, the consideration of actual anisotropic consolidation causes the characteristic period to decrease and the earthquake influence factor to increase.
基金Research Committee of the University of Macao under Grant No.MYRG2015-00048-FST
文摘Evaluation of the cyclic shear modulus of soils is a crucial but challenging task for many geotechnical earthquake engineering and soil dynamic issues. Improper determination of this property unnecessarily drives up design and maintenance costs or even leads to the construction of unsafe structures. Due to the complexities involved in the direct measurement, empirical curves for estimating the cyclic shear modulus have been commonly adopted in practice for simplicity and economical considerations. However, a systematic and robust approach for formulating a reliable model and empirical curve for cyclic shear modulus prediction for clayey soils is still lacking. In this study, the Bayesian model class selection approach is utilized to identify the most significant soil parameters affecting the normalized cyclic shear modulus and a reliable predictive model for normally to moderately over-consolidated clays is proposed. Results show that the predictability and reliability of the proposed model out performs the well-known empirical models. Finally, a new design chart is established for practical usage.
基金the National Natural Science Foundation of China(Grant No.51971178)the Astronautics Supporting Technology Foundation of China(Grant No.2019-HT-XG)+2 种基金the Natural Science Foundation of Shaanxi Province,China(Grant No.2019JM-344)the Russian Science Foundation(Grant No.20-62-46003)the Fundamental Research Funds for the Central Universities,China(Grant Nos.3102019ghxm007 and 3102017JC01003).
文摘A relationship between thermal effects and relaxation of the high-frequency shear modulus upon heat treatment of bulk Zr48(Cu5/6Ag1/6)44Al8 metallic glass is found.This relationship is attributed to the relaxation of a interstitial-type defect system frozen-in from the melt upon glass production.Calorimetric data show that thermal effects occurring on heating include heat release below the glass transition temperature,heat absorption above it and heat release caused by crystallization.The equation derived within the Interstitialcy theory can be used to calculate the shear modulus relaxation using the calorimetric data.The obtained results are used to trace the defect concentration as functions of temperature and thermal prehistory.
基金Project supported by the National Natural Science Foundation of China (Grant Nos 10232040 and 10672149)the foundation of Laboratory for Shock Wave and Detonation Physics Research, China Academy of Engineering Physics (Grant No 9140C6702020603)
文摘Asymmetric plate impact experiments are conducted on LY12 aluminium alloy in a pressure range of 85-131 GPa. The longitudinal sound speeds axe obtained from the time-resolved particle speed profiles of the specimen measured with Velocity Interferometer System for Any Reflector （VISAR） technique, and they are shown to be good agreement with our previously reported data of this alloy in a pressure range of 20-70 GPa, and also with those of 2024 aluminium reported by McQueen. Using all of the longitudinal speeds and the corresponding bulk speeds calculated from the Gruneisen equation of state （EOS）, shear moduli of LY12 aluminium alloy are obtained. A comparison of the shear moduli in the solid phase region with those estimated from the Steinberg model demonstrate that the latter are systematically lower than the measurements. By re-analysing the pressure effect on the shear modulus, a modified equation is proposed, in which the pressure term of P/η^1/3 in the Steinberg model is replaced by a linear term. Good agreement between experiments and the modified equation is obtained, which implies that the shear modulus of LY12 aluminium varies linearly both with pressure and with temperature throughout the whole solid phase region. On the other hand, shear modulus of aluminium in a solid-liquid mixed phrase region decreases gradually and smoothly, a feature that is very different from the drastic dropping at the melting point under static conditions.
基金This project is supported by the National Natural Science Foundation of China (Grant No50479045)
文摘A plane strain analysis based on the generalized Biot＇s equation is utilized to investigate the wave-induced response of a poro-elastic seabed with variable shear modulus. By employing integral transform and Frobenins methods, the transient and steady solutions for the wave-inducod pore water pressure, effective stresses and displacements are analytically derived in detail. Verification is available through the reduction to the simple case of homogeneous seabed. The numerical results indicate that the inclusion of variable shear modulus significantly affects the wave-induced seabed response.
基金National Science Foundation of China under Grant No.41202186the Zhejiang National Science Foundation under Grant No.LQ12E08007
文摘The fabric anisotropy of a granular soil deposit can strongly infl uence its engineering properties and behavior. This paper presents the results of a novel experimental study designed to examine the effects of fabric anisotropy on smallstrain stiffness and its evolution with loading on the elastic shear modulus of granular materials under a K0 condition. Two primary categories of fabric anisotropy, i.e., deposition-induced and particle shape-induced, are investigated. Toyoura sand deposits with relative densities of 40% and 80% were prepared using deposition angles oriented at 0o and 90o. Piezoelectric transducers were used to obtain the elastic shear modulus in the vertical and horizontal directions(Gvh and Ghh). The measurements indicate distinct differences in the values of G with respect to the different deposition angles. Particle shapeinduced fabric anisotropy was examined using four selected sands. It was concluded that sphericity is a controlling factor dominating the small-strain stiffness of granular materials. The degree of fabric anisotropy proves to be a good indicatorin the characterization of stress-induced fabric evolution during loading and unloading stress cycles. The experimental data were used to calibrate an existing micromechanical model, which was able to represent the behavior of the granular material and the degree of fabric anisotropy reasonably well.
基金financially supported by the National Natural Science Foundation of China (Grant Nos. 11774247 and U2030107)Sichuan University Innovation Research Program of China (Grant No. 2020SCUNL107)。
文摘High-pressure Raman scattering from hexagonal close-packed(HCP) metals Os and Re have been extended up to 200 GPa, and the pressure-dependent shear modulus C_(44)has been deduced from the Raman-active mode E_(28), which is generated from the adjacent vibration of atoms in hexagonal planes, providing the valuable information about the elastic properties for HCP metals under high pressure. Combined with the available data of HCP metals from previous works,a further study indicates that the C_(44)/C_(44)ratio would be close to a constant value, 0.01, with increasing atomic number of metals. The results obtained from high-pressure Raman scattering will allow us to probe the elastic anisotropy of the HCP metals at very high pressure.
基金Ministry of Science and Technology of Chinaand the Earthquake Science Foundation of China Under GrandNo.102033
文摘An error analysis of the dynamic shear modulus of stiff specimens from tests performed by a new resonant column device developed by the Institute of Engineering Mechanics, China was conducted. A modified approach for calculating the dynamic shear modulus of the stiff specimens is presented. The error formula of the tests was deduced and parameters that impact the accuracy of the test were identified. Using six steel specimens with known standard stiffness as a base, a revised dynamic shear modulus calculation for stiff specimens was formulated by comparing three of the models. The maximum error between the test results and the calculated results shown by curves from both the free-vibration and the resonant-vibration tests is less than 6%. The free-vibration and resonant-vibration tests for three types of stiff samples with a known modulus indicate that the maximum deviation between the actual and the tested value using the modified approach were less than 10%. As a result, the modified approach presented here is shown to be reliable and the new device can be used for testing dynamic shear modulus of any stiff materials at low shear strain levels
基金The Science and Technology Ministration of China and the Earthquake Science Foundation of China (Grand No. 102033)
文摘The dynamic shear modulus (DSM) is the most basic soil parameter in earthquake or other dynamic loading conditions and can be obtained through testing in the field or in the laboratory. The effect of consolidation ratios on the maximum DSM for two types of sand is investigated by using resonant column tests. And, an increment formula to obtain the maximum DSM for cases of consolidation ratio κc>1 is presented. The results indicate that the maximum DSM rises rapidly when κc is near 1 and then slows down, which means that the power function of the consolidation ratio increment κc-1 can be used to describe the variation of the maximum DSM due to κc>1. The results also indicate that the increase in the maximum DSM due to κc>1 is significantly larger than that predicted by Hardin and Black's formula.
文摘Effects of the tempering temperature and time on the shear modulus of Fe-Mn based alloys have been studied.The results show that(ΔG/G)-Tcurves of tempered alloys containing Cr and Ti have two extreme values—maximum and minimum,and that the curves of tem- pered alloys containing Cr,Ni,W and C only have a maximum value.This is the reason that Ni,W and C decrease the transformation point T_N of the antiferromagnetism.The ΔG_λ ef- feet increases gradually with the rise of tempering temperature or with the increase of tem- pering time.
基金Project(020940) supported by the Natural Science Foundation of Guangdong Province,China
文摘To solve the problems of divergence,low accuracy and project application of membrane wrinkling analysis,an analysis method of zero shear modulus and equivalent stiffness was proposed.This method is an improvement to the previous method (Method I) of local coordinate transposition and stiffness equivalence.The new method is derived and the feasibility is theoretically proved.A small-scale membrane structure is analyzed by the two methods,and the results show that the computational efficiency of the new method (Method II) is approximately 23 times that of Method I.When Method II is applied to a large-scale membrane stadium structure,it is found that this new method can quickly make the second principal stress of one way wrinkled elements zero,and make the two principal stresses of two-way wrinkled elements zero as well.It could attain the correct load responses right after the appearance of wrinkled elements,which indicates that Method II can be applied to wrinkling analysis of large-scale membrane structures.
