The ballistic impact identification method for the helicopter Tail Drive Shaft System(TDSS)isn't yet comprehensive,which affects helicopter flight safety.This paper proposes a ballistic impact identification metho...The ballistic impact identification method for the helicopter Tail Drive Shaft System(TDSS)isn't yet comprehensive,which affects helicopter flight safety.This paper proposes a ballistic impact identification method for the TDSS based on vibration response analysis.Based on the Johnson-Cook constitutive model and failure criteria,the ballistic impact finite element simulation model is established,which is verified by the ballistic impact experiment of the Tail Drive Shaft(TDS).Considering the ballistic impact excitation force,the dynamic model of the TDSS with ballistic impact is established,which is verified by finite element commercial software.If a bullet hits the TDS,the bending vibration displacement increases sharply at a certain moment and then significantly increases but remains stable.Meanwhile,the critical speed component appears in the frequency-domain response of bending vibration,and then the speed component significantly increases but remains stable.What's more,the axis trajectory exhibits a sudden,large-scale,and irregular whirling motion at a certain moment,followed by a significant increase but remains stable.Furthermore,if the axial vibration response is small,the bullet core shooting should be considered vertically or at a small incident angle,otherwise,it should be considered at a large incident angle.展开更多
According to the theoretical analysis and calculation on the base ofcontinuous mass system, the simulation experimental investigation on active control of torsionalvibration in a turbogenerator shaft system is conduct...According to the theoretical analysis and calculation on the base ofcontinuous mass system, the simulation experimental investigation on active control of torsionalvibration in a turbogenerator shaft system is conducted. A test installation with the excitation ofgenerator motor and multi-stepped shaft system is established to simulate the torsional vibration ofa turbogenerator rotor shaft system, and to examine the active control strategy presented. Someuseful results are reached in the experimental study.展开更多
The dynamic performance of the coupling shaft system in a carpet tufting machine is the most critical factor affecting the carpet tufting machine's efficiency,and the product quality of the tufted carpet. To deter...The dynamic performance of the coupling shaft system in a carpet tufting machine is the most critical factor affecting the carpet tufting machine's efficiency,and the product quality of the tufted carpet. To determine how to avoid resonance produced by the coupling shaft system's vibration during the weaving process,the dynamic performance of a coupling shaft system in a carpet tufting machine was analyzed. Focusing on a DHGN801D-400 carpet tufting machine,a dynamic model of coupling shaft system was established by utilizing transfer matrix methodology. On the basis of this model,the natural frequencies and mode shapes of the coupling shaft system were obtained through simulations. The correctness of the theoretical model and the dynamic performance of the coupling shaft system were validated by experiments. The first order natural frequency of the coupling shaft system was close to 600 r / min. A conclusion can thus be drawn that operating the carpet tufting machine near this speed should be avoided as much as possible.展开更多
According to the structure cha racteristies of a turbo-generator rotor shaft system,a torsionalvibration model of a large-size rotor shaft system with an elastic distributed structure has been estab-lished,and the tor...According to the structure cha racteristies of a turbo-generator rotor shaft system,a torsionalvibration model of a large-size rotor shaft system with an elastic distributed structure has been estab-lished,and the torsional vibration wave equation under the different boundary and initial conditions aswell as the impact of the damp of each shaft has been deduced.In the meanwhile,the inherent character-istics of a 300 MW turbo-generator rotor system is studied analytically and calculate with analyticalmethods.展开更多
In this study,the coupled torsional-transverse vibration of a propeller shaft system owing to the misalignment caused by the shaft rotation was investigated.The proposed numerical model is based on the modified versio...In this study,the coupled torsional-transverse vibration of a propeller shaft system owing to the misalignment caused by the shaft rotation was investigated.The proposed numerical model is based on the modified version of the Jeffcott rotor model.The equation of motion describing the harmonic vibrations of the system was obtained using the Euler-Lagrange equations for the associated energy functional.Experiments considering different rotation speeds and axial loads acting on the propulsion shaft system were performed to verify the numerical model.The effects of system parameters such as shaft length and diameter,stiffness and damping coefficients,and cross-section eccentricity were also studied.The cross-section eccentricity increased the displacement response,yet coupled vibrations were not initially observed.With the increase in the eccentricity,the interaction between two vibration modes became apparent,and the agreement between numerical predictions and experimental measurements improved.Given the results,the modified version of the Jeffcott rotor model can represent the coupled torsional-transverse vibration of propulsion shaft systems.展开更多
The stability and nonlinear dynamic behavior of drilling shaft system in copper stave deep hole drilling were analyzed. The effects of the fluctuation of the cutting force, the mass eccentricity and the hydrodynamic f...The stability and nonlinear dynamic behavior of drilling shaft system in copper stave deep hole drilling were analyzed. The effects of the fluctuation of the cutting force, the mass eccentricity and the hydrodynamic forces of cutting fluid could be taken into consideration in the model of drilling shaft system. Based on the isoparametric finite element method, the variational form of Reynolds equation in hydrodynamic fluid was used to calculate nonlinear hydrodynamic forces and their Jacobian matrices simultaneously. In the stability analysis, a new shooting method for rapidly determining the periodic orbit of the nonlinear drilling shaft system and its period was presented by rebuilding the traditional shooting method and changing the time scale. Through the combination of theories with experiment, the correctness and effectiveness of the above methods are verified by using the Floquet theory. The results show that the mass eccentricity can inhibit the whirling motion of drilling shaft to some extent.展开更多
Aiming at providing with high-load capability in active vibration control of large-scale rotor system, a new type of active actuator to simultaneously reduce the dangers of low frequency flexural and torsional vibrati...Aiming at providing with high-load capability in active vibration control of large-scale rotor system, a new type of active actuator to simultaneously reduce the dangers of low frequency flexural and torsional vibrations is designed. The actuator employs electro-hydraulic system and can provide a high and circumferential load. To initialize new research, the characteristics of various kinds of active actuators to control rotor shaft vibration are briefly introduced. The purpose of this paper is to introduce the preliminary results via presenting the structure, functions and operating principles, in particular, the working process of the electro-hydraulic system of the new actuator which includes a set of high speed electromagnetic valves and a series of sloping cone-shaped openings, and presenting the transmission relationships among the control parameters from control signals into the valves to active load onto shaft. The course of the work is dynamic, and a series of spatial forces and moments are put on the shaft to get an external resultant force to reduce excitations that induce vibration of shafts. By checking states of vibration, the actuator can control the impulse width and the interval of injection time for applying different control force to a vibration shaft in two circumference directions through the regulating action of a set of combination directional control valves. The results from simulating analysis and experiment show evidence of that this design can satisfy the case of active process of decreasing of flexural and torsional vibrations.展开更多
1.IntroductionWith the increase of the capacity of the turbine generator set,the safety of the shaft system of the set(including the exciter)isthreatened for the following three reasons:1.The length of the shaft syste...1.IntroductionWith the increase of the capacity of the turbine generator set,the safety of the shaft system of the set(including the exciter)isthreatened for the following three reasons:1.The length of the shaft system increases.The length of theshaft system is 15 m for a 50 MW set,32-40 m for a 300 MW set and90 m for a 900 MW nuclear power set.The increased number of theconcentrated masses leads to the increase of both the number of展开更多
BACKGROUND Humeral shaft fractures are common and vary by age,with high-energy trauma observed in younger adults and low-impact injuries in older adults.Radial nerve palsy is a frequent complication.Treatment ranges f...BACKGROUND Humeral shaft fractures are common and vary by age,with high-energy trauma observed in younger adults and low-impact injuries in older adults.Radial nerve palsy is a frequent complication.Treatment ranges from nonoperative methods to surgical interventions such as intramedullary K-wires,which promote faster rehabilitation and improved elbow mobility.AIM To evaluate the outcomes of managing humeral shaft fractures using closed reduction and internal fixation with flexible intramedullary K-wires.METHODS This was a retrospective cohort study analyzing the medical records of patients with humeral shaft fractures managed with flexible intramedullary K-wires at King Abdulaziz Medical City,using non-random sampling and descriptive analysis for outcome evaluation.RESULTS This study assessed the clinical outcomes of 20 patients treated for humeral shaft fractures with intramedullary K-wires.Patients were predominantly male(n=16,80%),had an average age of 39.2 years,and a mean body mass index of 29.5 kg/m^(2).The fractures most frequently occurred in the middle third of the humerus(n=14,70%),with oblique fractures being the most common type(n=7,35%).All surgeries used general anesthesia and a posterior approach,with no intraoperative complications reported.Postoperatively,all patients achieved clinical and radiological union(n=20,100%),and the majority(n=13,65%)reached an elbow range of motion from 0 to 150 degrees.CONCLUSION These results suggest that intramedullary K-wire fixation may be an effective option for treating humeral shaft fractures,with favorable outcomes in range of motion recovery,fracture union,and a low rate of intraoperative complications.展开更多
Linked tetra shaft and double cantilever flat flap gate is a new type of structure in water conservancy projects,but the traditional method is now adopted in its design.In order to the application and dissemination ...Linked tetra shaft and double cantilever flat flap gate is a new type of structure in water conservancy projects,but the traditional method is now adopted in its design.In order to the application and dissemination of the type of sluice,this paper researches the difficult points of design advance,through researching the motion locus & stress coundition of linked tetra shaft system.The writer will build up the mathmatical model and handle it with the computer.Thus,we can achieve the modern desing on the basis of the software of linked tetra shaft system development.展开更多
Shaft alignment is an important technique during installation and maintenance of a rotating machine. A high-precision laser alignment system has been designed with dual PSDs (Position Sensing Detector) to change tradi...Shaft alignment is an important technique during installation and maintenance of a rotating machine. A high-precision laser alignment system has been designed with dual PSDs (Position Sensing Detector) to change traditional manual way of shaft alignment and to make the measurement easier and more accurate. The system is comprised of two small measuring units (laser transmitter and detector) and a PDA (Personal Digital Assistant) with measurement software. The laser alignment system with dual PSDs was improved on a single PSD system, and yields higher measurement accuracy than the previous design, and has been successful for designing and implements actual shaft alignment. In the system, the range of offset measurement is ±4 mm, and the resolution is 1.5 μm, with accuracy being less than 2 μm.展开更多
Aiming at the shortcomings of traditional contact measurement methods such as low measurement efficiency,high cost and low accuracy,a non-contact optical measurement method based on the laser displacement sensor is pr...Aiming at the shortcomings of traditional contact measurement methods such as low measurement efficiency,high cost and low accuracy,a non-contact optical measurement method based on the laser displacement sensor is proposed.According to the relevant regulations of the coaxiality error evaluation standard and the structural characteristics of the compound gear shaft,we have designed and built a set of supporting software system as well as a hardware test platform.In this paper,the distance difference threshold and scale threshold methods are used to eliminate outlier data.The least squares circle is selected to calculate the center of the circle and the minimum containment cylinder axis method is used as the reference axis of the composite gear shaft.Compensated by the standard step shaft calibration,the coaxiality error of the composite gear shaft can be measured to be within 0.01 mm in less than two minutes.The range value of the multi-section measurement test is 0.065 mm.The average coaxiality error is∅0.476 mm.展开更多
The crack fault is one of the most common faults in the rotor system,and researchers have paid close attention to its fault diagnosis.However,most studies focus on discussing the dynamic response characteristics cause...The crack fault is one of the most common faults in the rotor system,and researchers have paid close attention to its fault diagnosis.However,most studies focus on discussing the dynamic response characteristics caused by the crack rather than estimating the crack depth and position based on the obtained vibration signals.In this paper,a novel crack fault diagnosis and location method for a dual-disk hollow shaft rotor system based on the Radial basis function(RBF)network and Pattern recognition neural network(PRNN)is presented.Firstly,a rotor system model with a breathing crack suitable for a short-thick hollow shaft rotor is established based on the finite element method,where the crack's periodic opening and closing pattern and different degrees of crack depth are considered.Then,the dynamic response is obtained by the harmonic balance method.By adjusting the crack parameters,the dynamic characteristics related to the crack depth and position are analyzed through the amplitude-frequency responses and waterfall plots.The analysis results show that the first critical speed,first subcritical speed,first critical speed amplitude,and super-harmonic resonance peak at the first subcritical speed can be utilized for the crack fault diagnosis.Based on this,the RBF network and PRNN are adopted to determine the depth and approximate location of the crack respectively by taking the above dynamic characteristics as input.Test results show that the proposed method has high fault diagnosis accuracy.This research proposes a crack detection method adequate for the hollow shaft rotor system,where the crack depth and position are both unknown.展开更多
Shaft alignment is an important technique during installation and maintenance of a rotating machine. A high-precision laser alignment system has been designed with dual PSDs (Position Sensing Detector) to change tradi...Shaft alignment is an important technique during installation and maintenance of a rotating machine. A high-precision laser alignment system has been designed with dual PSDs (Position Sensing Detector) to change traditional manual way of shaft alignment and to make the measurement easier and more accurate. The system is comprised of two small measuring units (laser transmitter and detector) and a PDA (Personal Digital Assistant) with the measurement software. The laser alignment system with dual PSDs was improved on a single PSD system,and it gets higher measurement accuracy than the previous design,and it has been succeeded in designing and implement for actual shaft alignment. In the system,the range of offset measurement is ±4 mm,and the resolution is 1.5 μm,and the accuracy is less than 2 μm.展开更多
BACKGROUND Whether operation is superior to non-operation for humeral shaft fracture remains debatable.We hypothesized that operation could decrease the nonunion and reintervention rates and increase the functional ou...BACKGROUND Whether operation is superior to non-operation for humeral shaft fracture remains debatable.We hypothesized that operation could decrease the nonunion and reintervention rates and increase the functional outcomes.AIM To compare the clinical efficacy between operative and nonoperative approaches for humeral shaft fractures.METHODS We searched the PubMed,Web of Science,ScienceDirect,and Cochrane databases from 1990 to December 2023 for clinical trials and cohort studies comparing the effects of operative and conservative methods on humeral shaft fractures.Two investigators independently extracted data from the eligible studies,and the other two assessed the methodological quality of each study.The quality of the included studies was assessed using the Cochrane risk bias or Newcastle-Ottawa Scale.The nonunion,reintervention and the overall complications and functional scores were pooled and analyzed using Review Manager software(version 5.3).RESULTS A total of four randomized control trials and 13 cohort studies were included,with 1285 and 1346 patients in the operative and nonoperative groups,respectively.Patients in the operative group were treated with a plate or nail,whereas those in the conservative group were managed with splint or functional bracing.Four studies were assessed as having a high risk of bias,and the other 13 were of a low risk of bias according to the Newcastle-Ottawa Scale or Cochrane risk bias tool.The operative group had a significantly decreased rate of nonunion[odds ratio(OR)0.30;95%CI:0.23 to 0.40,reintervention(OR:0.33;95%CI:0.24 to 0.47),and overall complications(OR:0.62;95%CI:0.49 to 0.78)].The pooled effect of the Disabilities of Arm,Shoulder,and Hand score showed a significant difference at 3[mean difference(MD)-8.26;95%CI:-13.60 to-2.92],6(MD:-6.72;95%CI:-11.34 to-2.10),and 12 months(MD:-2.55;95%CI:-4.36 to-0.74).The pooled effect of Visual Analog Scale scores and the Constant-Murley score did not significantly differ between the two groups.CONCLUSION This systematic review and meta-analysis revealed a trend of rapid functional recovery and decreased rates of nonunion and reintervention after operation for humeral shaft fracture compared to conservative treatment.展开更多
In recent years, the crack fault is one of the most common faults in the rotor system and it is still a challenge for crack position diagnosis in the hollow shaft rotor system. In this paper, a method based on the Con...In recent years, the crack fault is one of the most common faults in the rotor system and it is still a challenge for crack position diagnosis in the hollow shaft rotor system. In this paper, a method based on the Convolutional Neural Network and deep metric learning(CNN-C) is proposed to effectively identify the crack position for a hollow shaft rotor system. Center-loss function is used to enhance the performance of neural network. Main contributions include: Firstly, the dynamic response of the dual-disks hollow shaft rotor system is obtained. The analysis results show that the crack will cause super-harmonic resonance, and the peak value of it is closely related to the position and depth of the crack. In addition, the amplitude near the non-resonant region also has relationship with the crack parameters. Secondly, we proposed an effective crack position diagnosis method which has the highest 99.04% recognition accuracy compared with other algorithms. Then,the influence of penalty factor on CNN-C performance is analyzed, which shows that too high penalty factor will lead to the decline of the neural network performance. Finally, the feature vectors are visualized via t-distributed Stochastic Neighbor Embedding(t-SNE). Naive Bayes classifier(NB) and K-Nearest Neighbor algorithm(KNN) are used to verify the validity of the feature vectors extracted by CNN-C. The results show that NB and KNN have more regular decision boundaries and higher recognition accuracy on the feature vectors data set extracted by CNN-C,indicating that the feature vectors extracted by CNN-C have great intra-class compactness and inter-class separability.展开更多
The online detection of metal shaft parameters,such as torque,power and deformation,is widely applied in engineering projects.The power supply of metal shafts is the key to the detection reliability and practicality.H...The online detection of metal shaft parameters,such as torque,power and deformation,is widely applied in engineering projects.The power supply of metal shafts is the key to the detection reliability and practicality.However,traditional slip ring and battery power supply are limited in reliability and service life.In this paper,a side-mounted inductive power supply system for the rotating metal shaft is designed by using a Utype core.The equivalent reluctance and circuit models of the system are analyzed,and the methods of improving the coupling coefficient and transmission efficiency are proposed from theoretical analysis.Through the finite element simulation analysis of the system,the general relationships between the transmission power and efficiency of the system and the number of coil turns,the working frequency and the load are analyzed.The accuracy of theoretical analysis and simulation analysis is verified by the practical power transmission experiments.This paper provides a novel and reliable power supply method for inductive power supply of rotating equipment,and enriches the solutions of rotating power supply.展开更多
In this study, the influence of geometrical parameters on the curve veering phenomenon in a tor-sional system with stepped shaft is investigated. Three approximate solutions including finite el-ement, Rayleigh-Ritz an...In this study, the influence of geometrical parameters on the curve veering phenomenon in a tor-sional system with stepped shaft is investigated. Three approximate solutions including finite el-ement, Rayleigh-Ritz and discretization methods, along with an exact solution are employed to obtain the natural frequencies of the structure. The study reveals that, under specific circumstances, the results obtained by approximate methods are very close to the exact solution. The curve veering behavior is manifested irrespective of the method employed. It is concluded that for the structure studied the curve veering behavior is not because of the approximate techniques used to compute the natural frequencies, and is an inherent behavior of the structure.展开更多
Introduction: The management of fractures of the tibia shaft is an important aspect of orthopaedic care, and the selection of the surgical method for fixation can substantially impact patient outcomes. The current rev...Introduction: The management of fractures of the tibia shaft is an important aspect of orthopaedic care, and the selection of the surgical method for fixation can substantially impact patient outcomes. The current review aims to compare the outcomes of adult tibia fractures treated with solid nails to those treated with hollow nails. Methods: A search on Scopus, PubMed, and Cochrane Library, using three keywords (Outcome, Tibia shaft fractures, Nail) was conducted in April 2023. Results were compiled and two independent reviewers screened and selected eligible articles After removing duplicates, titles and abstracts were read to exclude ineligible studies. Full-text articles of the remaining papers were read to select eligible studies which were further critically appraised to ascertain their methodological quality. The data extracted from the selected papers were synthesized using a combination of pooling of results, tests of statistical difference (t-test and chi-square) and narrative synthesis methods. Results: A total of 2295 articles were obtained from the databases and citation searching. A total of 9 papers were identified as eligible and included in the review. Findings revealed that there is no statistical difference in the outcomes of tibia fractures treated with either solid or hollow nail groups such as duration of surgery (p = 0.541), rate of delayed and non-union (p = 0.342), and rate of surgical site infections (p = 0.395). Conclusion: Intramedullary nailing of tibia shaft fractures with either solid or hollow nails have similar functional outcomes.展开更多
To enhance the operational capacity and space utilization of baffle-drop shafts,this study improved the traditional baffle-drop shaft by expanding the wet-side space,incorporating large rotation-angle baffles,and inst...To enhance the operational capacity and space utilization of baffle-drop shafts,this study improved the traditional baffle-drop shaft by expanding the wet-side space,incorporating large rotation-angle baffles,and installing overflow holes in the dividing wall.A three-dimensional turbulent model was developed using ANSYS Fluent to simulate the hydraulic characteristics of both traditional and new baffle-drop shafts across various flow rates.The simulation results demonstrated that the new shaft design allowed for discharge from both the wet and dry sides,significantly improving operational capacity,with the dry side capable of handling 40%of the inlet flow.Compared to the traditional shaft,the new design reduced shaft wall pressures and decreased the mean and standard deviation of pressure on typical baffles by 21%and 63%,respectively,therefore enhancing structural safety.Additionally,the new shaft achieved a 2%-12%higher energy dissipation rate than the traditional shaft across different flow rates.This study offers valuable insights for the design and optimization of drop shafts in deep tunnel drainage systems.展开更多
基金co-supported by the National Natural Science Foundation of China(No.52275061)the Postgraduate Research&Practice Innovation Program of Jiangsu Province,China(No.KYCX24_0562)。
文摘The ballistic impact identification method for the helicopter Tail Drive Shaft System(TDSS)isn't yet comprehensive,which affects helicopter flight safety.This paper proposes a ballistic impact identification method for the TDSS based on vibration response analysis.Based on the Johnson-Cook constitutive model and failure criteria,the ballistic impact finite element simulation model is established,which is verified by the ballistic impact experiment of the Tail Drive Shaft(TDS).Considering the ballistic impact excitation force,the dynamic model of the TDSS with ballistic impact is established,which is verified by finite element commercial software.If a bullet hits the TDS,the bending vibration displacement increases sharply at a certain moment and then significantly increases but remains stable.Meanwhile,the critical speed component appears in the frequency-domain response of bending vibration,and then the speed component significantly increases but remains stable.What's more,the axis trajectory exhibits a sudden,large-scale,and irregular whirling motion at a certain moment,followed by a significant increase but remains stable.Furthermore,if the axial vibration response is small,the bullet core shooting should be considered vertically or at a small incident angle,otherwise,it should be considered at a large incident angle.
基金This project is supported by National Natural Science Foundation of China (No.59575015) Education Ministry of China.
文摘According to the theoretical analysis and calculation on the base ofcontinuous mass system, the simulation experimental investigation on active control of torsionalvibration in a turbogenerator shaft system is conducted. A test installation with the excitation ofgenerator motor and multi-stepped shaft system is established to simulate the torsional vibration ofa turbogenerator rotor shaft system, and to examine the active control strategy presented. Someuseful results are reached in the experimental study.
基金National Natural Science Foundation of China(No.51175075)the Research and Innovation Project of Shanghai Municipal Education Commission,China(No.15ZZ034)
文摘The dynamic performance of the coupling shaft system in a carpet tufting machine is the most critical factor affecting the carpet tufting machine's efficiency,and the product quality of the tufted carpet. To determine how to avoid resonance produced by the coupling shaft system's vibration during the weaving process,the dynamic performance of a coupling shaft system in a carpet tufting machine was analyzed. Focusing on a DHGN801D-400 carpet tufting machine,a dynamic model of coupling shaft system was established by utilizing transfer matrix methodology. On the basis of this model,the natural frequencies and mode shapes of the coupling shaft system were obtained through simulations. The correctness of the theoretical model and the dynamic performance of the coupling shaft system were validated by experiments. The first order natural frequency of the coupling shaft system was close to 600 r / min. A conclusion can thus be drawn that operating the carpet tufting machine near this speed should be avoided as much as possible.
基金Supported by the Education Ministry of China for the OutstandingYouth Teacher Fund(D196001,G00023)
文摘According to the structure cha racteristies of a turbo-generator rotor shaft system,a torsionalvibration model of a large-size rotor shaft system with an elastic distributed structure has been estab-lished,and the torsional vibration wave equation under the different boundary and initial conditions aswell as the impact of the damp of each shaft has been deduced.In the meanwhile,the inherent character-istics of a 300 MW turbo-generator rotor system is studied analytically and calculate with analyticalmethods.
基金supported by the Scientific and Technological Research Council of Turkey(TUBITAK)2214-A International Doctoral Research Fellowship Programmewhile experiments were performed at the Wuhan University of Technology。
文摘In this study,the coupled torsional-transverse vibration of a propeller shaft system owing to the misalignment caused by the shaft rotation was investigated.The proposed numerical model is based on the modified version of the Jeffcott rotor model.The equation of motion describing the harmonic vibrations of the system was obtained using the Euler-Lagrange equations for the associated energy functional.Experiments considering different rotation speeds and axial loads acting on the propulsion shaft system were performed to verify the numerical model.The effects of system parameters such as shaft length and diameter,stiffness and damping coefficients,and cross-section eccentricity were also studied.The cross-section eccentricity increased the displacement response,yet coupled vibrations were not initially observed.With the increase in the eccentricity,the interaction between two vibration modes became apparent,and the agreement between numerical predictions and experimental measurements improved.Given the results,the modified version of the Jeffcott rotor model can represent the coupled torsional-transverse vibration of propulsion shaft systems.
基金Project(2007CB707706) supported by the Major State Basic Research Development Program of ChinaProjects(2007E213,2007E203) supported by the Natural Science Foundation of Shaanxi Province,China
文摘The stability and nonlinear dynamic behavior of drilling shaft system in copper stave deep hole drilling were analyzed. The effects of the fluctuation of the cutting force, the mass eccentricity and the hydrodynamic forces of cutting fluid could be taken into consideration in the model of drilling shaft system. Based on the isoparametric finite element method, the variational form of Reynolds equation in hydrodynamic fluid was used to calculate nonlinear hydrodynamic forces and their Jacobian matrices simultaneously. In the stability analysis, a new shooting method for rapidly determining the periodic orbit of the nonlinear drilling shaft system and its period was presented by rebuilding the traditional shooting method and changing the time scale. Through the combination of theories with experiment, the correctness and effectiveness of the above methods are verified by using the Floquet theory. The results show that the mass eccentricity can inhibit the whirling motion of drilling shaft to some extent.
基金supported by National Natural Science Foundation of China (No.50475112)National Hi-Tech Research and Development Program of China (863 Program,No.2006AA110112).
文摘Aiming at providing with high-load capability in active vibration control of large-scale rotor system, a new type of active actuator to simultaneously reduce the dangers of low frequency flexural and torsional vibrations is designed. The actuator employs electro-hydraulic system and can provide a high and circumferential load. To initialize new research, the characteristics of various kinds of active actuators to control rotor shaft vibration are briefly introduced. The purpose of this paper is to introduce the preliminary results via presenting the structure, functions and operating principles, in particular, the working process of the electro-hydraulic system of the new actuator which includes a set of high speed electromagnetic valves and a series of sloping cone-shaped openings, and presenting the transmission relationships among the control parameters from control signals into the valves to active load onto shaft. The course of the work is dynamic, and a series of spatial forces and moments are put on the shaft to get an external resultant force to reduce excitations that induce vibration of shafts. By checking states of vibration, the actuator can control the impulse width and the interval of injection time for applying different control force to a vibration shaft in two circumference directions through the regulating action of a set of combination directional control valves. The results from simulating analysis and experiment show evidence of that this design can satisfy the case of active process of decreasing of flexural and torsional vibrations.
文摘1.IntroductionWith the increase of the capacity of the turbine generator set,the safety of the shaft system of the set(including the exciter)isthreatened for the following three reasons:1.The length of the shaft system increases.The length of theshaft system is 15 m for a 50 MW set,32-40 m for a 300 MW set and90 m for a 900 MW nuclear power set.The increased number of theconcentrated masses leads to the increase of both the number of
基金approved by King Abdullah International Medical Research Center Ethics Committee(approval No.0000074524).
文摘BACKGROUND Humeral shaft fractures are common and vary by age,with high-energy trauma observed in younger adults and low-impact injuries in older adults.Radial nerve palsy is a frequent complication.Treatment ranges from nonoperative methods to surgical interventions such as intramedullary K-wires,which promote faster rehabilitation and improved elbow mobility.AIM To evaluate the outcomes of managing humeral shaft fractures using closed reduction and internal fixation with flexible intramedullary K-wires.METHODS This was a retrospective cohort study analyzing the medical records of patients with humeral shaft fractures managed with flexible intramedullary K-wires at King Abdulaziz Medical City,using non-random sampling and descriptive analysis for outcome evaluation.RESULTS This study assessed the clinical outcomes of 20 patients treated for humeral shaft fractures with intramedullary K-wires.Patients were predominantly male(n=16,80%),had an average age of 39.2 years,and a mean body mass index of 29.5 kg/m^(2).The fractures most frequently occurred in the middle third of the humerus(n=14,70%),with oblique fractures being the most common type(n=7,35%).All surgeries used general anesthesia and a posterior approach,with no intraoperative complications reported.Postoperatively,all patients achieved clinical and radiological union(n=20,100%),and the majority(n=13,65%)reached an elbow range of motion from 0 to 150 degrees.CONCLUSION These results suggest that intramedullary K-wire fixation may be an effective option for treating humeral shaft fractures,with favorable outcomes in range of motion recovery,fracture union,and a low rate of intraoperative complications.
文摘Linked tetra shaft and double cantilever flat flap gate is a new type of structure in water conservancy projects,but the traditional method is now adopted in its design.In order to the application and dissemination of the type of sluice,this paper researches the difficult points of design advance,through researching the motion locus & stress coundition of linked tetra shaft system.The writer will build up the mathmatical model and handle it with the computer.Thus,we can achieve the modern desing on the basis of the software of linked tetra shaft system development.
基金Project (No. 60337030) partly supported by the National NaturalScience Foundation of China
文摘Shaft alignment is an important technique during installation and maintenance of a rotating machine. A high-precision laser alignment system has been designed with dual PSDs (Position Sensing Detector) to change traditional manual way of shaft alignment and to make the measurement easier and more accurate. The system is comprised of two small measuring units (laser transmitter and detector) and a PDA (Personal Digital Assistant) with measurement software. The laser alignment system with dual PSDs was improved on a single PSD system, and yields higher measurement accuracy than the previous design, and has been successful for designing and implements actual shaft alignment. In the system, the range of offset measurement is ±4 mm, and the resolution is 1.5 μm, with accuracy being less than 2 μm.
基金supported by the National Natural Science Foundation of China(No.51975293)Aeronautical Science Foundation of China (No. 2019ZD052010)
文摘Aiming at the shortcomings of traditional contact measurement methods such as low measurement efficiency,high cost and low accuracy,a non-contact optical measurement method based on the laser displacement sensor is proposed.According to the relevant regulations of the coaxiality error evaluation standard and the structural characteristics of the compound gear shaft,we have designed and built a set of supporting software system as well as a hardware test platform.In this paper,the distance difference threshold and scale threshold methods are used to eliminate outlier data.The least squares circle is selected to calculate the center of the circle and the minimum containment cylinder axis method is used as the reference axis of the composite gear shaft.Compensated by the standard step shaft calibration,the coaxiality error of the composite gear shaft can be measured to be within 0.01 mm in less than two minutes.The range value of the multi-section measurement test is 0.065 mm.The average coaxiality error is∅0.476 mm.
基金Supported by National Natural Science Foundation of China (Grant No.11972129)National Science and Technology Major Project of China (Grant No.2017-IV-0008-0045)+1 种基金Heilongjiang Provincial Natural Science Foundation (Grant No.YQ2022A008)the Fundamental Research Funds for the Central Universities。
文摘The crack fault is one of the most common faults in the rotor system,and researchers have paid close attention to its fault diagnosis.However,most studies focus on discussing the dynamic response characteristics caused by the crack rather than estimating the crack depth and position based on the obtained vibration signals.In this paper,a novel crack fault diagnosis and location method for a dual-disk hollow shaft rotor system based on the Radial basis function(RBF)network and Pattern recognition neural network(PRNN)is presented.Firstly,a rotor system model with a breathing crack suitable for a short-thick hollow shaft rotor is established based on the finite element method,where the crack's periodic opening and closing pattern and different degrees of crack depth are considered.Then,the dynamic response is obtained by the harmonic balance method.By adjusting the crack parameters,the dynamic characteristics related to the crack depth and position are analyzed through the amplitude-frequency responses and waterfall plots.The analysis results show that the first critical speed,first subcritical speed,first critical speed amplitude,and super-harmonic resonance peak at the first subcritical speed can be utilized for the crack fault diagnosis.Based on this,the RBF network and PRNN are adopted to determine the depth and approximate location of the crack respectively by taking the above dynamic characteristics as input.Test results show that the proposed method has high fault diagnosis accuracy.This research proposes a crack detection method adequate for the hollow shaft rotor system,where the crack depth and position are both unknown.
基金Funded by the National Natural Science Foundation of China (60337030) .
文摘Shaft alignment is an important technique during installation and maintenance of a rotating machine. A high-precision laser alignment system has been designed with dual PSDs (Position Sensing Detector) to change traditional manual way of shaft alignment and to make the measurement easier and more accurate. The system is comprised of two small measuring units (laser transmitter and detector) and a PDA (Personal Digital Assistant) with the measurement software. The laser alignment system with dual PSDs was improved on a single PSD system,and it gets higher measurement accuracy than the previous design,and it has been succeeded in designing and implement for actual shaft alignment. In the system,the range of offset measurement is ±4 mm,and the resolution is 1.5 μm,and the accuracy is less than 2 μm.
基金Supported by Natural Science Foundation of Chongqing,China,No.CSTB2023NSCQ-MSX1080.
文摘BACKGROUND Whether operation is superior to non-operation for humeral shaft fracture remains debatable.We hypothesized that operation could decrease the nonunion and reintervention rates and increase the functional outcomes.AIM To compare the clinical efficacy between operative and nonoperative approaches for humeral shaft fractures.METHODS We searched the PubMed,Web of Science,ScienceDirect,and Cochrane databases from 1990 to December 2023 for clinical trials and cohort studies comparing the effects of operative and conservative methods on humeral shaft fractures.Two investigators independently extracted data from the eligible studies,and the other two assessed the methodological quality of each study.The quality of the included studies was assessed using the Cochrane risk bias or Newcastle-Ottawa Scale.The nonunion,reintervention and the overall complications and functional scores were pooled and analyzed using Review Manager software(version 5.3).RESULTS A total of four randomized control trials and 13 cohort studies were included,with 1285 and 1346 patients in the operative and nonoperative groups,respectively.Patients in the operative group were treated with a plate or nail,whereas those in the conservative group were managed with splint or functional bracing.Four studies were assessed as having a high risk of bias,and the other 13 were of a low risk of bias according to the Newcastle-Ottawa Scale or Cochrane risk bias tool.The operative group had a significantly decreased rate of nonunion[odds ratio(OR)0.30;95%CI:0.23 to 0.40,reintervention(OR:0.33;95%CI:0.24 to 0.47),and overall complications(OR:0.62;95%CI:0.49 to 0.78)].The pooled effect of the Disabilities of Arm,Shoulder,and Hand score showed a significant difference at 3[mean difference(MD)-8.26;95%CI:-13.60 to-2.92],6(MD:-6.72;95%CI:-11.34 to-2.10),and 12 months(MD:-2.55;95%CI:-4.36 to-0.74).The pooled effect of Visual Analog Scale scores and the Constant-Murley score did not significantly differ between the two groups.CONCLUSION This systematic review and meta-analysis revealed a trend of rapid functional recovery and decreased rates of nonunion and reintervention after operation for humeral shaft fracture compared to conservative treatment.
基金the financial supports from the National Natural Science Foundation of China(No.11972129)the National Major Science and Technology Projects of China(No.2017-IV-0008-0045)。
文摘In recent years, the crack fault is one of the most common faults in the rotor system and it is still a challenge for crack position diagnosis in the hollow shaft rotor system. In this paper, a method based on the Convolutional Neural Network and deep metric learning(CNN-C) is proposed to effectively identify the crack position for a hollow shaft rotor system. Center-loss function is used to enhance the performance of neural network. Main contributions include: Firstly, the dynamic response of the dual-disks hollow shaft rotor system is obtained. The analysis results show that the crack will cause super-harmonic resonance, and the peak value of it is closely related to the position and depth of the crack. In addition, the amplitude near the non-resonant region also has relationship with the crack parameters. Secondly, we proposed an effective crack position diagnosis method which has the highest 99.04% recognition accuracy compared with other algorithms. Then,the influence of penalty factor on CNN-C performance is analyzed, which shows that too high penalty factor will lead to the decline of the neural network performance. Finally, the feature vectors are visualized via t-distributed Stochastic Neighbor Embedding(t-SNE). Naive Bayes classifier(NB) and K-Nearest Neighbor algorithm(KNN) are used to verify the validity of the feature vectors extracted by CNN-C. The results show that NB and KNN have more regular decision boundaries and higher recognition accuracy on the feature vectors data set extracted by CNN-C,indicating that the feature vectors extracted by CNN-C have great intra-class compactness and inter-class separability.
基金the National Natural Science Foundation of China(No.51475306)。
文摘The online detection of metal shaft parameters,such as torque,power and deformation,is widely applied in engineering projects.The power supply of metal shafts is the key to the detection reliability and practicality.However,traditional slip ring and battery power supply are limited in reliability and service life.In this paper,a side-mounted inductive power supply system for the rotating metal shaft is designed by using a Utype core.The equivalent reluctance and circuit models of the system are analyzed,and the methods of improving the coupling coefficient and transmission efficiency are proposed from theoretical analysis.Through the finite element simulation analysis of the system,the general relationships between the transmission power and efficiency of the system and the number of coil turns,the working frequency and the load are analyzed.The accuracy of theoretical analysis and simulation analysis is verified by the practical power transmission experiments.This paper provides a novel and reliable power supply method for inductive power supply of rotating equipment,and enriches the solutions of rotating power supply.
文摘In this study, the influence of geometrical parameters on the curve veering phenomenon in a tor-sional system with stepped shaft is investigated. Three approximate solutions including finite el-ement, Rayleigh-Ritz and discretization methods, along with an exact solution are employed to obtain the natural frequencies of the structure. The study reveals that, under specific circumstances, the results obtained by approximate methods are very close to the exact solution. The curve veering behavior is manifested irrespective of the method employed. It is concluded that for the structure studied the curve veering behavior is not because of the approximate techniques used to compute the natural frequencies, and is an inherent behavior of the structure.
文摘Introduction: The management of fractures of the tibia shaft is an important aspect of orthopaedic care, and the selection of the surgical method for fixation can substantially impact patient outcomes. The current review aims to compare the outcomes of adult tibia fractures treated with solid nails to those treated with hollow nails. Methods: A search on Scopus, PubMed, and Cochrane Library, using three keywords (Outcome, Tibia shaft fractures, Nail) was conducted in April 2023. Results were compiled and two independent reviewers screened and selected eligible articles After removing duplicates, titles and abstracts were read to exclude ineligible studies. Full-text articles of the remaining papers were read to select eligible studies which were further critically appraised to ascertain their methodological quality. The data extracted from the selected papers were synthesized using a combination of pooling of results, tests of statistical difference (t-test and chi-square) and narrative synthesis methods. Results: A total of 2295 articles were obtained from the databases and citation searching. A total of 9 papers were identified as eligible and included in the review. Findings revealed that there is no statistical difference in the outcomes of tibia fractures treated with either solid or hollow nail groups such as duration of surgery (p = 0.541), rate of delayed and non-union (p = 0.342), and rate of surgical site infections (p = 0.395). Conclusion: Intramedullary nailing of tibia shaft fractures with either solid or hollow nails have similar functional outcomes.
基金supported by the National Key Research and Development Program of China(Grant No.2021YFD1700802).
文摘To enhance the operational capacity and space utilization of baffle-drop shafts,this study improved the traditional baffle-drop shaft by expanding the wet-side space,incorporating large rotation-angle baffles,and installing overflow holes in the dividing wall.A three-dimensional turbulent model was developed using ANSYS Fluent to simulate the hydraulic characteristics of both traditional and new baffle-drop shafts across various flow rates.The simulation results demonstrated that the new shaft design allowed for discharge from both the wet and dry sides,significantly improving operational capacity,with the dry side capable of handling 40%of the inlet flow.Compared to the traditional shaft,the new design reduced shaft wall pressures and decreased the mean and standard deviation of pressure on typical baffles by 21%and 63%,respectively,therefore enhancing structural safety.Additionally,the new shaft achieved a 2%-12%higher energy dissipation rate than the traditional shaft across different flow rates.This study offers valuable insights for the design and optimization of drop shafts in deep tunnel drainage systems.
