An optimal measurement pose number searching method was designed to improve the pose selection method.Several optimal robot measurement configurations were added to an initial pre-selected optimal configuration set to...An optimal measurement pose number searching method was designed to improve the pose selection method.Several optimal robot measurement configurations were added to an initial pre-selected optimal configuration set to establish a new configuration set for robot calibration one by one.The root mean squares (RMS) of the errors of each end-effector poses after being calibrated by these configuration sets were calculated.The optimal number of the configuration set corresponding to the least RMS of pose error was then obtained.Calibration based on those poses selected by this algorithm can get higher end-effector accuracy,meanwhile consumes less time.An optimal pose set including optimal 25 measurement configurations is found during the simulation.Tracking errors after calibration by using these poses are 1.54,1.61 and 0.86 mm,and better than those before calibration which are 7.79,7.62 and 8.29 mm,even better than those calibrated by the random method which are 2.22,2.35 and 1.69 mm in directions X,Y and Z,respectively.展开更多
A new solution to the inverse position analysis of the redundant serial robot is presented.The inverse position analysis problem of the redundant serial robot is transformed into a minimization problem and then the op...A new solution to the inverse position analysis of the redundant serial robot is presented.The inverse position analysis problem of the redundant serial robot is transformed into a minimization problem and then the optimization method is adopted to solve the nonlinear least square problem with the analytic form of a new Jacobi matrix.In this way,the inverse solution of the redundant serial robot can be searched out quickly under the desired precision when the positions of the three non-collinear end effector points are given.The inverse position analysis of the 7R redundant serial robot is illustrated as an example and the simulation results verify the efficiency of the proposed algorithm.展开更多
The paper presents a new solution of inverse displacement analysis of the general six degree-of-freedom serial robot.The inverse displacement analysis of the general serial robot is transformed into a minimization pro...The paper presents a new solution of inverse displacement analysis of the general six degree-of-freedom serial robot.The inverse displacement analysis of the general serial robot is transformed into a minimization problem and then the optimization method is adopted to solve the nonlinear least squares problem with the analytic form of new Jacobian matrix.In this way,joint variables of the general serial robot can be searched out quickly under the desired precision when positions of the three non-collinear end effector points are given.Compared with the general Newton iterative method,the proposed algorithm can search out the solution when the robot is at the singular configuration and the initial configuration used in the optimization method may also be the singular configuration.So the convergence domain is bigger than that of the general Newton iterative method.Another advantage of the proposed algorithm is that positions of the three non-collinear end effector points are usually much easier to be measured than the orientation of the end effector.The inverse displacement analysis of the general 6R(six-revolute-joint) serial robot is illustrated as an example and the simulation results verify the efficiency of the proposed algorithm.Because the three non-collinear points can be selected at random,the method can be applied to any other types of serial robots.展开更多
Revealing the relations among robotic comprehensive performance,configuration,scales and working tasks is the basis to optimize robotic mechanism. Due to the correlation and diversity of the single performance indexes...Revealing the relations among robotic comprehensive performance,configuration,scales and working tasks is the basis to optimize robotic mechanism. Due to the correlation and diversity of the single performance indexes,statistical principles of linear dimension reduction and nonlinear dimension reduction are introduced into comprehensive performance analysis and evaluation for typical serial robot. The robotic mechanism's configuration,scales and task with the best comprehensive performance can be obtained by principal component analysis( PCA) and kernel principal component analysis( KPCA) respectively. The results show that KPCA can reveal the nonlinear relations among different single performance indexes more effectively and provide more comprehensive performance information than PCA. Thus,task-oriented method of serial robot for mechanism analysis and evaluation is proposed,which also provides scientific research basis for the mechanism synthesis and optimum task order.展开更多
In order to further improve the serial ports communication mode of the general Flex Pendant for industrial robot,a multiple serial communication mode is put forward. It is used to meet the stability of data transmissi...In order to further improve the serial ports communication mode of the general Flex Pendant for industrial robot,a multiple serial communication mode is put forward. It is used to meet the stability of data transmission,transmission distance,transmission speed,anti-interference and cost-effective. Using ADUM1201 single direction dual channel digital isolator,two pieces of MAX13487 E and a piece of MAX3232 chip to transmit data and files, and to control chip’ s electrical level. Selecting the RS232, RS422 and RS485 communication mode,the serial ports of the general Flex Pendant of industrial robot is optimized.展开更多
The concept of legged-robot stability training with a training platform is proposed and a serial-parallel mechanism platform with 6 degrees of freedom is designed for this target. The designed platform is composed of ...The concept of legged-robot stability training with a training platform is proposed and a serial-parallel mechanism platform with 6 degrees of freedom is designed for this target. The designed platform is composed of 4-DOF parallel mechanism with spherical joints and prismatic pairs,and 2-DOF serial mechanism with prismatic pairs. With this design,the platform has advantages of low platform countertop,big workspace,high carrying capacity and high stiffness. On the basis of DOF analysis and computation of space mechanism,weight supporting auxiliary mechanism and raceways-balls supporting mechanism are designed,so as to improve the stiffness of designed large platform and payload capacity of servo motors. And then the whole structure design work of the platform is done. Meanwhile,this paper derives the analytical solutions of forward kinematics, inverse kinematics and inverse dynamics. The error analysis model of position and orientation is established. And then the simulation is done in ADAMS to ensure the correctness and feasibility of this design.展开更多
In the robotic community more and more hands are developed. Based on theexperience of HIT Hand and DLR Hand II, a smaller and easier manufactured dexterous robot hand withmultisen-sory function and high integration is...In the robotic community more and more hands are developed. Based on theexperience of HIT Hand and DLR Hand II, a smaller and easier manufactured dexterous robot hand withmultisen-sory function and high integration is jointly developed. The prototype of the hand issuccessfully built. It has 4 fingers in total 13-DOFs (degree of freedom). Each finger has 3-DOFsand 4 joints, the last 2 joints are mechanically coupled by means of four-bar linkage mechanism. Italso has an additional DOF to realize motion of the thumb relative to the palm. The fingertip forcecan reach up to 10 N. Full integration of mechanical body, actuation system, multisensory system andelectronics is a significant feature. DSP based control system is implemented in PCI busarchitecture and the serial communication between the hand and DSP needs only 2 lines.展开更多
针对工业机器人在高度制造领域精度不高的问题,本文提出了一种基于POE模型的工业机器人运动学参数二次辨识方法。阐述了基于指数积(Product of exponential, POE)模型的运动学误差模型构建方法,并建立基于POE误差模型的适应度函数;为实...针对工业机器人在高度制造领域精度不高的问题,本文提出了一种基于POE模型的工业机器人运动学参数二次辨识方法。阐述了基于指数积(Product of exponential, POE)模型的运动学误差模型构建方法,并建立基于POE误差模型的适应度函数;为实现高精度的参数辨识,提出了一种二次辨识方法,先利用改进灰狼优化算法(Improved grey wolf optimizer, IGWO)实现运动学参数误差的粗辨识,初步将Staubli TX60型机器人的平均位置误差和平均姿态误差分别从(0.648 mm, 0.212°)降低为(0.457 mm, 0.166°);为进一步提高机器人的精度性能,再通过LM(Levenberg-Marquard)算法进行参数误差的精辨识,最终将Staubli TX60型机器人平均位置误差和平均姿态误差进一步降低为(0.237 mm, 0.063°),机器人平均位置误差和平均姿态误差分别降低63.4%和70.2%。为了验证上述二次辨识方法的稳定性,随机选取5组辨识数据集和验证数据集进行POE误差模型的参数误差辨识,结果表明提出的二次辨识方法能够稳定、精确地辨识工业机器人运动学参数误差。展开更多
基金Project(2008AA04Z203) supported by the National High Technology Research and Development Program of China
文摘An optimal measurement pose number searching method was designed to improve the pose selection method.Several optimal robot measurement configurations were added to an initial pre-selected optimal configuration set to establish a new configuration set for robot calibration one by one.The root mean squares (RMS) of the errors of each end-effector poses after being calibrated by these configuration sets were calculated.The optimal number of the configuration set corresponding to the least RMS of pose error was then obtained.Calibration based on those poses selected by this algorithm can get higher end-effector accuracy,meanwhile consumes less time.An optimal pose set including optimal 25 measurement configurations is found during the simulation.Tracking errors after calibration by using these poses are 1.54,1.61 and 0.86 mm,and better than those before calibration which are 7.79,7.62 and 8.29 mm,even better than those calibrated by the random method which are 2.22,2.35 and 1.69 mm in directions X,Y and Z,respectively.
基金the National Natural Science Foundation of China (No.50905102)the China Postdoctoral Science Foundation (No.200801199)the Natural Science Foundation of Guangdong Province (Nos.8351503101000001 and 10151503101000033)
文摘A new solution to the inverse position analysis of the redundant serial robot is presented.The inverse position analysis problem of the redundant serial robot is transformed into a minimization problem and then the optimization method is adopted to solve the nonlinear least square problem with the analytic form of a new Jacobi matrix.In this way,the inverse solution of the redundant serial robot can be searched out quickly under the desired precision when the positions of the three non-collinear end effector points are given.The inverse position analysis of the 7R redundant serial robot is illustrated as an example and the simulation results verify the efficiency of the proposed algorithm.
基金Funded by National Natural Science Foundation of China (No. 50905102)the Natural Science Foundation of Guangdong Province (Nos. 10151503101000033 and 8351503101000001)the Building Fund for the Academic Innovation Team of Shantou University (No. ITC10003)
文摘The paper presents a new solution of inverse displacement analysis of the general six degree-of-freedom serial robot.The inverse displacement analysis of the general serial robot is transformed into a minimization problem and then the optimization method is adopted to solve the nonlinear least squares problem with the analytic form of new Jacobian matrix.In this way,joint variables of the general serial robot can be searched out quickly under the desired precision when positions of the three non-collinear end effector points are given.Compared with the general Newton iterative method,the proposed algorithm can search out the solution when the robot is at the singular configuration and the initial configuration used in the optimization method may also be the singular configuration.So the convergence domain is bigger than that of the general Newton iterative method.Another advantage of the proposed algorithm is that positions of the three non-collinear end effector points are usually much easier to be measured than the orientation of the end effector.The inverse displacement analysis of the general 6R(six-revolute-joint) serial robot is illustrated as an example and the simulation results verify the efficiency of the proposed algorithm.Because the three non-collinear points can be selected at random,the method can be applied to any other types of serial robots.
基金Sponsored by the National Natural Science Foundation of China(Grant No.51075005)the Beijing City Science and Technology Project(Grant No.Z131100005313009)
文摘Revealing the relations among robotic comprehensive performance,configuration,scales and working tasks is the basis to optimize robotic mechanism. Due to the correlation and diversity of the single performance indexes,statistical principles of linear dimension reduction and nonlinear dimension reduction are introduced into comprehensive performance analysis and evaluation for typical serial robot. The robotic mechanism's configuration,scales and task with the best comprehensive performance can be obtained by principal component analysis( PCA) and kernel principal component analysis( KPCA) respectively. The results show that KPCA can reveal the nonlinear relations among different single performance indexes more effectively and provide more comprehensive performance information than PCA. Thus,task-oriented method of serial robot for mechanism analysis and evaluation is proposed,which also provides scientific research basis for the mechanism synthesis and optimum task order.
基金supported by the National Key Technology R&D Program(2015BAK06B04)the key technologies R&D Program of Tianjin(14ZCZDSF00022)
文摘In order to further improve the serial ports communication mode of the general Flex Pendant for industrial robot,a multiple serial communication mode is put forward. It is used to meet the stability of data transmission,transmission distance,transmission speed,anti-interference and cost-effective. Using ADUM1201 single direction dual channel digital isolator,two pieces of MAX13487 E and a piece of MAX3232 chip to transmit data and files, and to control chip’ s electrical level. Selecting the RS232, RS422 and RS485 communication mode,the serial ports of the general Flex Pendant of industrial robot is optimized.
基金Sponsored by the National High-Tech Research and Development Program(Grant No.2006AA04Z201)
文摘The concept of legged-robot stability training with a training platform is proposed and a serial-parallel mechanism platform with 6 degrees of freedom is designed for this target. The designed platform is composed of 4-DOF parallel mechanism with spherical joints and prismatic pairs,and 2-DOF serial mechanism with prismatic pairs. With this design,the platform has advantages of low platform countertop,big workspace,high carrying capacity and high stiffness. On the basis of DOF analysis and computation of space mechanism,weight supporting auxiliary mechanism and raceways-balls supporting mechanism are designed,so as to improve the stiffness of designed large platform and payload capacity of servo motors. And then the whole structure design work of the platform is done. Meanwhile,this paper derives the analytical solutions of forward kinematics, inverse kinematics and inverse dynamics. The error analysis model of position and orientation is established. And then the simulation is done in ADAMS to ensure the correctness and feasibility of this design.
文摘In the robotic community more and more hands are developed. Based on theexperience of HIT Hand and DLR Hand II, a smaller and easier manufactured dexterous robot hand withmultisen-sory function and high integration is jointly developed. The prototype of the hand issuccessfully built. It has 4 fingers in total 13-DOFs (degree of freedom). Each finger has 3-DOFsand 4 joints, the last 2 joints are mechanically coupled by means of four-bar linkage mechanism. Italso has an additional DOF to realize motion of the thumb relative to the palm. The fingertip forcecan reach up to 10 N. Full integration of mechanical body, actuation system, multisensory system andelectronics is a significant feature. DSP based control system is implemented in PCI busarchitecture and the serial communication between the hand and DSP needs only 2 lines.
文摘针对工业机器人在高度制造领域精度不高的问题,本文提出了一种基于POE模型的工业机器人运动学参数二次辨识方法。阐述了基于指数积(Product of exponential, POE)模型的运动学误差模型构建方法,并建立基于POE误差模型的适应度函数;为实现高精度的参数辨识,提出了一种二次辨识方法,先利用改进灰狼优化算法(Improved grey wolf optimizer, IGWO)实现运动学参数误差的粗辨识,初步将Staubli TX60型机器人的平均位置误差和平均姿态误差分别从(0.648 mm, 0.212°)降低为(0.457 mm, 0.166°);为进一步提高机器人的精度性能,再通过LM(Levenberg-Marquard)算法进行参数误差的精辨识,最终将Staubli TX60型机器人平均位置误差和平均姿态误差进一步降低为(0.237 mm, 0.063°),机器人平均位置误差和平均姿态误差分别降低63.4%和70.2%。为了验证上述二次辨识方法的稳定性,随机选取5组辨识数据集和验证数据集进行POE误差模型的参数误差辨识,结果表明提出的二次辨识方法能够稳定、精确地辨识工业机器人运动学参数误差。
