Numerical studies of the flow past a circular cylinder at Reynolds number 1.4 × 105 and NACA0021 airfoil at the angle of attack 60° have been carried out by scale-adaptive simulation （SAS） and detached edd...Numerical studies of the flow past a circular cylinder at Reynolds number 1.4 × 105 and NACA0021 airfoil at the angle of attack 60° have been carried out by scale-adaptive simulation （SAS） and detached eddy simu- lation （DES）, in comparison with the existing experimental data. The new version of the model developed by Egorov and Menter is assessed, and advantages and disadvantages of the SAS simulation are analyzed in detail to provide guidance for industrial application in the future. Moreover, the mechanism of the scale-adaptive characteristics in separated regions is discussed, which is obscure in previous analyses. It is con- cluded that： the mean flow properties satisfactorily agree with the experimental results for the SAS simulation, although the prediction of the second order turbulent statistics in the near wake region is just reasonable. The SAS model can produce a larger magnitude of the turbulent kinetic energy in the recir- culation bubble, and, consequently, a smaller recirculation region and a more rapid recovery of the mean velocity out- side the recirculation region than the DES approach with the same grid resolution. The vortex shedding is slightly less irregular with the SAS model than with the DES approach, probably due to the higher dissipation of the SAS simulation under the condition of the coarse mesh.展开更多
Accurate prediction of unsteady separated turbulent flows remains one of the toughest tasks and a practi cal challenge for turbulence modeling. In this paper, a 2D flow past a circular cylinder at Reynolds number 3,90...Accurate prediction of unsteady separated turbulent flows remains one of the toughest tasks and a practi cal challenge for turbulence modeling. In this paper, a 2D flow past a circular cylinder at Reynolds number 3,900 is numerically investigated by using the technique of unsteady RANS （URANS）. Some typical linear and nonlinear eddy viscosity turbulence models （LEVM and NLEVM） and a quadratic explicit algebraic stress model （EASM） are evaluated. Numerical results have shown that a high-performance cubic NLEVM, such as CLS, are superior to the others in simulating turbulent separated flows with unsteady vortex shedding.展开更多
A pulsed-wire wall probe measurement system was developed in this paper,which can be used for measuring wall Parameters in separated flow- The operating princi-ple was described and the way of probe calibration was gi...A pulsed-wire wall probe measurement system was developed in this paper,which can be used for measuring wall Parameters in separated flow- The operating princi-ple was described and the way of probe calibration was given. Wall parameters of back-ward-facing and forward-facing step flow were measured,and the wall nows structure andcharacters were revealed.展开更多
To study the effects of factors such as electromagnetic field and electron temperature on the ion extraction characteristics (extraction time, collision loss ratio) in atomic vapor laser isotope separation (AVLIS),...To study the effects of factors such as electromagnetic field and electron temperature on the ion extraction characteristics (extraction time, collision loss ratio) in atomic vapor laser isotope separation (AVLIS), 2 D electron equilibrium model was used to analyze and simulate the ion extraction process. The collisions between particles mainly considered charge exchanges between isotopic ions and atoms, which were treated by using cross section. The results show that the electric field and electron temperature have significant effects on the ion extraction characteristics: the stronger the electric field is, the higher the electron temperature is; the shorter the extraction time is, the less the collision loss ratio is, and moderate constant magnetic field has few effects on them. Key words atomic vapor laser isotope separation (AVLIS); ion extraction; charge exchange cross section; collision loss ratio展开更多
This article investigates the separated flow around the bent-nose biconic, in which the second ordered TVD(Total Variation Diminishing) method is applied. The governing cqua-tion is a thin layer Navier-Stokes equation...This article investigates the separated flow around the bent-nose biconic, in which the second ordered TVD(Total Variation Diminishing) method is applied. The governing cqua-tion is a thin layer Navier-Stokes equation. The surface pressure distribution at the leeward side is a little higher in the vicinity of the symmetrical plane. This seems to be caused by the development of the vortex at the leeward side due to the separated flow. The location of a separation line and the size are in very good agreement with the experiment. Also the secondary separation is captured very clearly.展开更多
A separated flow model with stochastical trajectories has been developed to describe the fluid flow in a bubble stirred ladle.The bubble dispersion,turbulent characteristics and gas-liquid interactions can be predicte...A separated flow model with stochastical trajectories has been developed to describe the fluid flow in a bubble stirred ladle.The bubble dispersion,turbulent characteristics and gas-liquid interactions can be predicted by this mathematical model.The bubble flow as a dispersed phase is treated in a Lagrangian frame of reference and the analysis of the turbulent flow for liquid phase is conducted in a Eulerian field.The interactions between bubbles and liquid phases are considered as a bubble source term in the control equation for a continuous phase. The Monte Carlo sampling method is used to determine the bubble trajectories.The homoge- neous flow model is also taken into consideration so that it can be compared with the sepa- rated flow model.Numerical predictions using a water model of a ladle show that the pre- dicted results of the separated flow model agree satisfactorily with the experimental results, but the prediction of the homogeneous flow model are not in good agreement with the experi- mental results.展开更多
This paper prcsents an investigation of two-dimensional separated flow in and around a submerged curved intake by experiment and computation. The eniptic Navier-Stokes equations are employed which are discreted in bod...This paper prcsents an investigation of two-dimensional separated flow in and around a submerged curved intake by experiment and computation. The eniptic Navier-Stokes equations are employed which are discreted in body-fitted coordinate system by the SIMPLE method. The results show that the flow separation exists near and behind the inlet and the duct flow is distorted. Comparison between the computational and experimental data is fairly satisfactory.展开更多
The finite difference method (FDM) is applied in the present paper to solve the unsteady NHS equations for incompressible fluids. ADI and SLOR methods are served for the vorticity equation and the Poisson equation for...The finite difference method (FDM) is applied in the present paper to solve the unsteady NHS equations for incompressible fluids. ADI and SLOR methods are served for the vorticity equation and the Poisson equation for ψ respectively. The upwind scheme is used for the convective terms. The moving boundary conditions are specially treated, and the effects of outlet conditions on the flow field are abo examined. Numerical results obtained show that the spoiler's oscillation induces forming, growing and shedding of the vortices. The shedding frequency of vortices is equal to that of the spoiler's oscillation. The forced unsteady separated flows under the present investigation depend mainly on the reduced frequency. At low reduced frequency, the vortices shed from the spoiler interact weakly with each other, and move downstream at an almost uniform speed of 038 V∞. At high reduced frequency, the interaction between the adjacent vortices strengthens. They close up to and rotate around each other, and eventually, merge into one vortex.展开更多
The effect of nanosecond pulsed dielectric barrier discharge(NS-DBD) plasma flow separation control is closely related to the actuation frequency,because it involves the interaction between plasma-induced vortexes and...The effect of nanosecond pulsed dielectric barrier discharge(NS-DBD) plasma flow separation control is closely related to the actuation frequency,because it involves the interaction between plasma-induced vortexes and separated flow.In order to study the mechanism of NS-DBD plasma flow separation control over a swept wing,especially the influence of the actuation frequency,at first,experimental studies of the actuation frequencies at 100 Hz are conducted to validate the numerical simulation method.Then,numerical studies of different actuation frequencies which are 50 Hz,100 Hz,160 Hz,200 Hz,500 Hz,and 1000 Hz,respectively are conducted.The interaction between the plasma-induced vortexes and the separated flow is analyzed.Results show that there is a range of the actuation frequency which includes the frequency(160 Hz) calculated by the average aerodynamic chord length to make the control effect good,but when the actuation frequencies are too low(50 Hz) or too high(1000 Hz),the control effect will get worse.The former is because plasmainduced vortexes disappear in a period within an actuation cycle;the latter is because plasma-induced vortexes cannot develop completely,resulting in a weak vortex intensity.展开更多
The increasing performance demands of modern aero engines necessitate the integrated design of compressor transition ducts with upstream components to reduce the axial length of the engine.However,this design approach...The increasing performance demands of modern aero engines necessitate the integrated design of compressor transition ducts with upstream components to reduce the axial length of the engine.However,this design approach narrows the spacing between the stator and the strut,making traditional research on transition ducts only with struts unsuitable.The numerical results and experimental oil flow visualization results were utilized to reconstruct the three-dimensional flow structures in the stator passages under various operating conditions.Additionally,numerical methods were employed to analyze the mechanisms of the strut's effect on the upstream stator in an aggressive transition duct.The results show that the strut potential field increases the load on the upstream stator,leading to severe blade surface separation and corner separation/stall,and redistributes the inflow angle of the upstream stators circumferentially,resulting in significant differences in the flow structures within the stator passages on both sides.The separation flows within the stator passages mainly manifest in five types:pressure surface separation vortex,suction surface concentrated shedding vortex,suction surface separation vortex,suction surface-corner stall separation vortex,and suction surface separation vortex pair.Under different operating conditions,the separation flows within the stator passages are always composed of a part of these five types or a transitional state between two of them.展开更多
The flow control at low Reynolds numbers is one of the most promising technologies in the field of aerodynamics,and it is also an important source of the innovation for novel aircraft.In this study,a new way of nonlin...The flow control at low Reynolds numbers is one of the most promising technologies in the field of aerodynamics,and it is also an important source of the innovation for novel aircraft.In this study,a new way of nonlinear flow control by interaction between two flexible flaps is proposed,and their flow control mechanism is studied employing the self-constructed immersed boundary-lattice Boltzmann-finite element method(IB-LB-FEM).The effects of the difference in material properties and flap length between the two flexible flaps on the nonlinear flow control of the airfoil are discussed.It is suggested that the relationship between the deformation of the two flexible flaps and the evolution of the vortex under the fluid-structure interaction(FSI).It is shown that the upstream flexible flap plays a key role in the flow control of the two flexible flaps.The FSI effect of the upstream flexible flap will change the unsteady flow behind it and affect the deformation of the downstream flexible flap.Two flexible flaps with different material properties and different lengths will change their own FSI characteristics by the induced vortex,effectively suppressing the flow separation on the airfoil’s upper surface.The interaction of two flexible flaps plays an extremely important role in improving the autonomy and adjustability of flow control.The numerical results will provide a theoretical basis and technical guidance for the development and application of a new flap passive control technology.展开更多
Numerical results of three-dimensional separated flow and heat transfer in an enlarged rectangular channel are presented in this paper.The expansion ratio and aspect ratio of the channel are 2.0 and 16.0,respectively....Numerical results of three-dimensional separated flow and heat transfer in an enlarged rectangular channel are presented in this paper.The expansion ratio and aspect ratio of the channel are 2.0 and 16.0,respectively.Reynolds number of the flow is 200 and it is over the critical Reynolds number.Over the critical Reynolds number,the flow in the symmetric channel becomes asymmetric and deflects to one side of the walls.Effects of the pulsating fluctuation at the inlet upon the flow in the channel are investigated.It is clarified that the inlet flow with a pulsating fluctuation of Strouhal number 0.05 and 0.10 strongly affects on the flow in the channel,and heat transfer on the walls is enhanced,especially on the wall surface covered with long separation bubble.On the other hand,the pulsation of St=0.0125 oscillates the shear layer more weakly than that of St=0.05,0.10 and the enhancement of heat transfer is smaller,though some vortices are shed from the vicinity of the side wall near the reattachment region.The oscillation of the main flow calms down gradually as the Strouhal number of the pulsation increases over 0.10.The influence of pulsation of St=0.20 on the flow is restricted in the near downstream of the step,and heat transfer on the walls is almost similar to that of the steady flow in the channel.展开更多
The vortex-in-cell method in the discrete vortex simulation for the separated flow around a bluff body is discussed,Some improvements are made.The separated flow around a circular cylinder in oscillatory flow is inves...The vortex-in-cell method in the discrete vortex simulation for the separated flow around a bluff body is discussed,Some improvements are made.The separated flow around a circular cylinder in oscillatory flow is investigated.展开更多
A turbulent separation-rcattachment flow in a two-dimensional asymmetrical curved-wall diffuser is studied by a two-dimensional laser doppler velocimeter.The turbulent boundary layer separates on the lower curved wall...A turbulent separation-rcattachment flow in a two-dimensional asymmetrical curved-wall diffuser is studied by a two-dimensional laser doppler velocimeter.The turbulent boundary layer separates on the lower curved wall under strong pressure gradient and then reattaches on a parallel channel.At the inlet of the diffuser,Reynolds number based on the diffuser height is 1.2×10~5 and the velocity is 25.2m/s.The re- sults of experiments are presented and analyzed in new defined streamline-aligned coordinates.The experiment shows that after Transitory Detachment Reynolds shear stress is negative in the near-wall backflow region. Their characteristics are approximately the same as in simple turbulent shear layers near the maximum Reynolds shear stress.A scale is formed using the maximum Reynolds shear stresses.It is found that a Reynolds shear stress similarity exists from separation to reattachment and the Schofield-Perry velocity law ex- ists in the forward shear flow.Both profiles are used in the experimental work that leads to the design of a new eddy-viscosity model.The length scale is taken from that developed by Schofield and Perry.The composite velocity scale is formed by the maximum Reynolds shear stress and the Schofield Perry velocity scale as well as the edge velocity of the boundary layer.The results of these experiments are presented in this paper展开更多
This paper presents the results of an experimental study of the unsteady nature of a hypersonic sepa- rated turbulent flow.The nominal test conditions were a freestream Mach number of 7.8 and a unit Reynolds number of...This paper presents the results of an experimental study of the unsteady nature of a hypersonic sepa- rated turbulent flow.The nominal test conditions were a freestream Mach number of 7.8 and a unit Reynolds number of 3.5x10^7/m.The separated flow was generated using finite span forward facing steps.An array of flush mounted high spatial resolution and fast response platinum film resistance thermometers was used to make mul- ti-channel measurements of the fluctuating surface heat trtansfer within the separated flow.Conditional sampling ana- lysis of the signals shows that the root of separation shock wave consists of a series of compression wave extending over a streamwise length about one half of the incoming boundary layer thickness.The compression waves con- verge into a single leading shock beyond the boundary layer.The shock structure is unsteady and undergoes large-scale motion in the streamwise direction.The length scale of the motion is about 22 percent of the upstream influence length of the separation shock wave.There exists a wide band of frequency of oscillations of the shock system.Most of the frequencies are in the range of 1-3 kHz.The heat transfer fluctuates intermittently between the undisturbed level and the disturbed level within the range of motion of the separation shock wave.This inter mittent phenomenon is considered as the consequence of the large-scale shock system oscillations.Downstream of the range of shock wave motion there is a separated region where the flow experiences continuous compression and no intermittency phenomenon is observed.展开更多
This paper describes a theoretical method for reconstruction of the skin friction topology in complex separated flows,which is developed based on the exact relation between skin friction and surface pressure through t...This paper describes a theoretical method for reconstruction of the skin friction topology in complex separated flows,which is developed based on the exact relation between skin friction and surface pressure through the boundary enstrophy flux(BEF).The key of this method is that a skin friction field is reconstructed from a surface pressure field as an inverse problem by applying a variational method.For applications,the approximate method is proposed,where the composite surface pressure field is given by a linear superposition of the base-flow surface pressure field and the surface pressure variation field and the base-flow BEF field is used as the first-order approximation.This approximate method is constructive in a mathematical sense since a complex skin friction field in separated flows can be reconstructed from some elemental skin friction structures(skin friction source/sink,vortex and their combinations)by a linear superposition of some simple surface pressure structures.The distinct topological features,such as critical points,separation lines and attachment lines,naturally occur as a result of such reconstruction.As examples,some elemental skin friction structures in separated flows are reconstructed in simulations,and the skin friction fields in shock-wave/boundary-layer interactions(SWBLIs)are reconstructed from pressure sensitive paint(PSP)images obtained in wind tunnel experiments.展开更多
Bottom water coning is the main reason to reduce the recovery of horizontal bottom water reservoir. By water coning, we mean the oil-water interface changes from a horizontal state to a mound-shaped cone and breaks th...Bottom water coning is the main reason to reduce the recovery of horizontal bottom water reservoir. By water coning, we mean the oil-water interface changes from a horizontal state to a mound-shaped cone and breaks through to the wellbore. Autonomous inflow control device(AICD) is an important instrument maintain normal production after bottom water coning, however, the resistance increasing ability of the swirl type AICD is insufficient at present, which seriously affects the water control effect. Aiming this problem, this paper designs a multi-stage resistance-increasing and composite type AICD. The separation mechanism of oil-water two phases in this structure, the resistance form of oil-water single phase and the resistance-increasing principle of water phase are analyzed. Establishing the dual-phase multi-stage separation and resistance-increasing model, and verified by measuring the throttling pressure drop and oil-water volume fraction of the AICD, it is found that the composite type AICD has the effect of ICD and AICD at the same time, which can balance the production rate of each well section at the initial stage of production, delay the occurrence of bottom water coning. In the middle and later stages of production, water-blocking can be effectively increased to achieve water control and stable production.After structural sensitivity analysis, the influence law of various structural parameters on the water control performance of composite AICD was obtained. The simulation calculation results show that,compared with the existing swirl type AICD, composite AICD has higher sensitivity to moisture content,the water phase throttling pressure drop is increased by 4.5 times on average. The composite AICD is suitable for the entire stage of horizontal well production.展开更多
The effects of the micro-ramps on supersonic turbulent flow over a forward-facing step（FFS） was experimentally investigated in a supersonic low-noise wind tunnel at Mach number 3 using nano-tracer planar laser scatt...The effects of the micro-ramps on supersonic turbulent flow over a forward-facing step（FFS） was experimentally investigated in a supersonic low-noise wind tunnel at Mach number 3 using nano-tracer planar laser scattering（NPLS）and particle image velocimetry（PIV） techniques. High spatiotemporal resolution images and velocity fields of supersonic flow over the testing model were captured. The fine structures and their spatial evolutionary characteristics without and with the micro-ramps were revealed and compared. The large-scale structures generated by the micro-ramps can survive the downstream FFS flowfield. The micro-ramps control on the flow separation and the separation shock unsteadiness was investigated by PIV results. With the micro-ramps, the reduction in the range of the reversal flow zone in streamwise direction is 50% and the turbulence intensity is also reduced. Moreover, the reduction in the average separated region and in separation shock unsteadiness are 47% and 26%, respectively. The results indicate that the micro-ramps are effective in reducing the flow separation and the separation shock unsteadiness.展开更多
A new hybrid model, which is based on domain decomposition and proposed by the authors is used for calculating the flow around a circular cylinder at low and middle Keulegan-Carpenter numbers (Kc=2～18)respectively.Th...A new hybrid model, which is based on domain decomposition and proposed by the authors is used for calculating the flow around a circular cylinder at low and middle Keulegan-Carpenter numbers (Kc=2～18)respectively.The vortex motion patterns in asymmetric regime,single pair(or transverse)regime and double pair(or diagonal)regime are successfully simulated.The calculated drag and inertial force coefficients are in better agreement with experimental data than other recent computational results.展开更多
Flow induced oscillation in a cavity and its suppression by means of acoustic excitation were studied both experimentally and numerically. In the experiment it was found that with the leading edge pure tone excitation...Flow induced oscillation in a cavity and its suppression by means of acoustic excitation were studied both experimentally and numerically. In the experiment it was found that with the leading edge pure tone excitation at some frequencies and intensities. the flow-induced oscillation in the cavity could be greatly suppressed. Cavity flows both with and without acoustic excitation were studied by solving the 2-D time-dependent Reynolds averaged Navier Stokes equations using explicit predictor-corrector difference algorithm of MacCormack. Effects of turbulence were simulated via Cebeci-Smith turbulence mode with relaxation modification. The computational and experimental results are compared. and good agreement is obtained.展开更多
基金the National Basic Research Program of China ("973" Project) (Grant No. 2009CB724104)
文摘Numerical studies of the flow past a circular cylinder at Reynolds number 1.4 × 105 and NACA0021 airfoil at the angle of attack 60° have been carried out by scale-adaptive simulation （SAS） and detached eddy simu- lation （DES）, in comparison with the existing experimental data. The new version of the model developed by Egorov and Menter is assessed, and advantages and disadvantages of the SAS simulation are analyzed in detail to provide guidance for industrial application in the future. Moreover, the mechanism of the scale-adaptive characteristics in separated regions is discussed, which is obscure in previous analyses. It is con- cluded that： the mean flow properties satisfactorily agree with the experimental results for the SAS simulation, although the prediction of the second order turbulent statistics in the near wake region is just reasonable. The SAS model can produce a larger magnitude of the turbulent kinetic energy in the recir- culation bubble, and, consequently, a smaller recirculation region and a more rapid recovery of the mean velocity out- side the recirculation region than the DES approach with the same grid resolution. The vortex shedding is slightly less irregular with the SAS model than with the DES approach, probably due to the higher dissipation of the SAS simulation under the condition of the coarse mesh.
文摘Accurate prediction of unsteady separated turbulent flows remains one of the toughest tasks and a practi cal challenge for turbulence modeling. In this paper, a 2D flow past a circular cylinder at Reynolds number 3,900 is numerically investigated by using the technique of unsteady RANS （URANS）. Some typical linear and nonlinear eddy viscosity turbulence models （LEVM and NLEVM） and a quadratic explicit algebraic stress model （EASM） are evaluated. Numerical results have shown that a high-performance cubic NLEVM, such as CLS, are superior to the others in simulating turbulent separated flows with unsteady vortex shedding.
文摘A pulsed-wire wall probe measurement system was developed in this paper,which can be used for measuring wall Parameters in separated flow- The operating princi-ple was described and the way of probe calibration was given. Wall parameters of back-ward-facing and forward-facing step flow were measured,and the wall nows structure andcharacters were revealed.
文摘To study the effects of factors such as electromagnetic field and electron temperature on the ion extraction characteristics (extraction time, collision loss ratio) in atomic vapor laser isotope separation (AVLIS), 2 D electron equilibrium model was used to analyze and simulate the ion extraction process. The collisions between particles mainly considered charge exchanges between isotopic ions and atoms, which were treated by using cross section. The results show that the electric field and electron temperature have significant effects on the ion extraction characteristics: the stronger the electric field is, the higher the electron temperature is; the shorter the extraction time is, the less the collision loss ratio is, and moderate constant magnetic field has few effects on them. Key words atomic vapor laser isotope separation (AVLIS); ion extraction; charge exchange cross section; collision loss ratio
文摘This article investigates the separated flow around the bent-nose biconic, in which the second ordered TVD(Total Variation Diminishing) method is applied. The governing cqua-tion is a thin layer Navier-Stokes equation. The surface pressure distribution at the leeward side is a little higher in the vicinity of the symmetrical plane. This seems to be caused by the development of the vortex at the leeward side due to the separated flow. The location of a separation line and the size are in very good agreement with the experiment. Also the secondary separation is captured very clearly.
文摘A separated flow model with stochastical trajectories has been developed to describe the fluid flow in a bubble stirred ladle.The bubble dispersion,turbulent characteristics and gas-liquid interactions can be predicted by this mathematical model.The bubble flow as a dispersed phase is treated in a Lagrangian frame of reference and the analysis of the turbulent flow for liquid phase is conducted in a Eulerian field.The interactions between bubbles and liquid phases are considered as a bubble source term in the control equation for a continuous phase. The Monte Carlo sampling method is used to determine the bubble trajectories.The homoge- neous flow model is also taken into consideration so that it can be compared with the sepa- rated flow model.Numerical predictions using a water model of a ladle show that the pre- dicted results of the separated flow model agree satisfactorily with the experimental results, but the prediction of the homogeneous flow model are not in good agreement with the experi- mental results.
文摘This paper prcsents an investigation of two-dimensional separated flow in and around a submerged curved intake by experiment and computation. The eniptic Navier-Stokes equations are employed which are discreted in body-fitted coordinate system by the SIMPLE method. The results show that the flow separation exists near and behind the inlet and the duct flow is distorted. Comparison between the computational and experimental data is fairly satisfactory.
基金The project is supported by the National Nature Science Foundation of China(NNSFC)
文摘The finite difference method (FDM) is applied in the present paper to solve the unsteady NHS equations for incompressible fluids. ADI and SLOR methods are served for the vorticity equation and the Poisson equation for ψ respectively. The upwind scheme is used for the convective terms. The moving boundary conditions are specially treated, and the effects of outlet conditions on the flow field are abo examined. Numerical results obtained show that the spoiler's oscillation induces forming, growing and shedding of the vortices. The shedding frequency of vortices is equal to that of the spoiler's oscillation. The forced unsteady separated flows under the present investigation depend mainly on the reduced frequency. At low reduced frequency, the vortices shed from the spoiler interact weakly with each other, and move downstream at an almost uniform speed of 038 V∞. At high reduced frequency, the interaction between the adjacent vortices strengthens. They close up to and rotate around each other, and eventually, merge into one vortex.
基金National Science and Technology Major Project (No.J2019-Ⅱ-0014-0035)Academician Workstation Foundation of the Green Aerotechnics Research Institute of Chonging Jiaotong University (No. GATRI2020C06003)。
文摘The effect of nanosecond pulsed dielectric barrier discharge(NS-DBD) plasma flow separation control is closely related to the actuation frequency,because it involves the interaction between plasma-induced vortexes and separated flow.In order to study the mechanism of NS-DBD plasma flow separation control over a swept wing,especially the influence of the actuation frequency,at first,experimental studies of the actuation frequencies at 100 Hz are conducted to validate the numerical simulation method.Then,numerical studies of different actuation frequencies which are 50 Hz,100 Hz,160 Hz,200 Hz,500 Hz,and 1000 Hz,respectively are conducted.The interaction between the plasma-induced vortexes and the separated flow is analyzed.Results show that there is a range of the actuation frequency which includes the frequency(160 Hz) calculated by the average aerodynamic chord length to make the control effect good,but when the actuation frequencies are too low(50 Hz) or too high(1000 Hz),the control effect will get worse.The former is because plasmainduced vortexes disappear in a period within an actuation cycle;the latter is because plasma-induced vortexes cannot develop completely,resulting in a weak vortex intensity.
基金supported by the National Natural Science Foundation of China(No.52276025)the Science Center for Gas Turbine Project of China(Nos.P2022-A-Ⅱ-001-001,P2022-A-Ⅱ-002-001 and P2022-B-Ⅱ-002-001)。
文摘The increasing performance demands of modern aero engines necessitate the integrated design of compressor transition ducts with upstream components to reduce the axial length of the engine.However,this design approach narrows the spacing between the stator and the strut,making traditional research on transition ducts only with struts unsuitable.The numerical results and experimental oil flow visualization results were utilized to reconstruct the three-dimensional flow structures in the stator passages under various operating conditions.Additionally,numerical methods were employed to analyze the mechanisms of the strut's effect on the upstream stator in an aggressive transition duct.The results show that the strut potential field increases the load on the upstream stator,leading to severe blade surface separation and corner separation/stall,and redistributes the inflow angle of the upstream stators circumferentially,resulting in significant differences in the flow structures within the stator passages on both sides.The separation flows within the stator passages mainly manifest in five types:pressure surface separation vortex,suction surface concentrated shedding vortex,suction surface separation vortex,suction surface-corner stall separation vortex,and suction surface separation vortex pair.Under different operating conditions,the separation flows within the stator passages are always composed of a part of these five types or a transitional state between two of them.
基金This work was supported by the National Natural Science Foundation of China(Grant Nos.92371201,52192633,11872293,and 92152301)the Natural Science Basic Research Program of Shaanxi(Grant Nos.2024JC-YBQN-0008,and 2022JC-03)+1 种基金Shaanxi Key Research and Development Program(Grant No.2022ZDLGY02-07)the Joint Natural Science Foundation of China with Guangdong Province for TianHe-II Supercomputer Resources,and the Research Start-up Foundation of Xi’an University of Science and Technology for the High-Level Talent.
文摘The flow control at low Reynolds numbers is one of the most promising technologies in the field of aerodynamics,and it is also an important source of the innovation for novel aircraft.In this study,a new way of nonlinear flow control by interaction between two flexible flaps is proposed,and their flow control mechanism is studied employing the self-constructed immersed boundary-lattice Boltzmann-finite element method(IB-LB-FEM).The effects of the difference in material properties and flap length between the two flexible flaps on the nonlinear flow control of the airfoil are discussed.It is suggested that the relationship between the deformation of the two flexible flaps and the evolution of the vortex under the fluid-structure interaction(FSI).It is shown that the upstream flexible flap plays a key role in the flow control of the two flexible flaps.The FSI effect of the upstream flexible flap will change the unsteady flow behind it and affect the deformation of the downstream flexible flap.Two flexible flaps with different material properties and different lengths will change their own FSI characteristics by the induced vortex,effectively suppressing the flow separation on the airfoil’s upper surface.The interaction of two flexible flaps plays an extremely important role in improving the autonomy and adjustability of flow control.The numerical results will provide a theoretical basis and technical guidance for the development and application of a new flap passive control technology.
基金These results were partly obtained with a supercomputer SX-9 of Cyberscience Center,Tohoku University
文摘Numerical results of three-dimensional separated flow and heat transfer in an enlarged rectangular channel are presented in this paper.The expansion ratio and aspect ratio of the channel are 2.0 and 16.0,respectively.Reynolds number of the flow is 200 and it is over the critical Reynolds number.Over the critical Reynolds number,the flow in the symmetric channel becomes asymmetric and deflects to one side of the walls.Effects of the pulsating fluctuation at the inlet upon the flow in the channel are investigated.It is clarified that the inlet flow with a pulsating fluctuation of Strouhal number 0.05 and 0.10 strongly affects on the flow in the channel,and heat transfer on the walls is enhanced,especially on the wall surface covered with long separation bubble.On the other hand,the pulsation of St=0.0125 oscillates the shear layer more weakly than that of St=0.05,0.10 and the enhancement of heat transfer is smaller,though some vortices are shed from the vicinity of the side wall near the reattachment region.The oscillation of the main flow calms down gradually as the Strouhal number of the pulsation increases over 0.10.The influence of pulsation of St=0.20 on the flow is restricted in the near downstream of the step,and heat transfer on the walls is almost similar to that of the steady flow in the channel.
文摘The vortex-in-cell method in the discrete vortex simulation for the separated flow around a bluff body is discussed,Some improvements are made.The separated flow around a circular cylinder in oscillatory flow is investigated.
文摘A turbulent separation-rcattachment flow in a two-dimensional asymmetrical curved-wall diffuser is studied by a two-dimensional laser doppler velocimeter.The turbulent boundary layer separates on the lower curved wall under strong pressure gradient and then reattaches on a parallel channel.At the inlet of the diffuser,Reynolds number based on the diffuser height is 1.2×10~5 and the velocity is 25.2m/s.The re- sults of experiments are presented and analyzed in new defined streamline-aligned coordinates.The experiment shows that after Transitory Detachment Reynolds shear stress is negative in the near-wall backflow region. Their characteristics are approximately the same as in simple turbulent shear layers near the maximum Reynolds shear stress.A scale is formed using the maximum Reynolds shear stresses.It is found that a Reynolds shear stress similarity exists from separation to reattachment and the Schofield-Perry velocity law ex- ists in the forward shear flow.Both profiles are used in the experimental work that leads to the design of a new eddy-viscosity model.The length scale is taken from that developed by Schofield and Perry.The composite velocity scale is formed by the maximum Reynolds shear stress and the Schofield Perry velocity scale as well as the edge velocity of the boundary layer.The results of these experiments are presented in this paper
基金The project supported by National Natural Science Foundation of China
文摘This paper presents the results of an experimental study of the unsteady nature of a hypersonic sepa- rated turbulent flow.The nominal test conditions were a freestream Mach number of 7.8 and a unit Reynolds number of 3.5x10^7/m.The separated flow was generated using finite span forward facing steps.An array of flush mounted high spatial resolution and fast response platinum film resistance thermometers was used to make mul- ti-channel measurements of the fluctuating surface heat trtansfer within the separated flow.Conditional sampling ana- lysis of the signals shows that the root of separation shock wave consists of a series of compression wave extending over a streamwise length about one half of the incoming boundary layer thickness.The compression waves con- verge into a single leading shock beyond the boundary layer.The shock structure is unsteady and undergoes large-scale motion in the streamwise direction.The length scale of the motion is about 22 percent of the upstream influence length of the separation shock wave.There exists a wide band of frequency of oscillations of the shock system.Most of the frequencies are in the range of 1-3 kHz.The heat transfer fluctuates intermittently between the undisturbed level and the disturbed level within the range of motion of the separation shock wave.This inter mittent phenomenon is considered as the consequence of the large-scale shock system oscillations.Downstream of the range of shock wave motion there is a separated region where the flow experiences continuous compression and no intermittency phenomenon is observed.
文摘This paper describes a theoretical method for reconstruction of the skin friction topology in complex separated flows,which is developed based on the exact relation between skin friction and surface pressure through the boundary enstrophy flux(BEF).The key of this method is that a skin friction field is reconstructed from a surface pressure field as an inverse problem by applying a variational method.For applications,the approximate method is proposed,where the composite surface pressure field is given by a linear superposition of the base-flow surface pressure field and the surface pressure variation field and the base-flow BEF field is used as the first-order approximation.This approximate method is constructive in a mathematical sense since a complex skin friction field in separated flows can be reconstructed from some elemental skin friction structures(skin friction source/sink,vortex and their combinations)by a linear superposition of some simple surface pressure structures.The distinct topological features,such as critical points,separation lines and attachment lines,naturally occur as a result of such reconstruction.As examples,some elemental skin friction structures in separated flows are reconstructed in simulations,and the skin friction fields in shock-wave/boundary-layer interactions(SWBLIs)are reconstructed from pressure sensitive paint(PSP)images obtained in wind tunnel experiments.
基金supported by National Natural Science Foundation(52204050)Sichuan Science and Technology Program(2021ZHCG0013,22ZDYF3009)。
文摘Bottom water coning is the main reason to reduce the recovery of horizontal bottom water reservoir. By water coning, we mean the oil-water interface changes from a horizontal state to a mound-shaped cone and breaks through to the wellbore. Autonomous inflow control device(AICD) is an important instrument maintain normal production after bottom water coning, however, the resistance increasing ability of the swirl type AICD is insufficient at present, which seriously affects the water control effect. Aiming this problem, this paper designs a multi-stage resistance-increasing and composite type AICD. The separation mechanism of oil-water two phases in this structure, the resistance form of oil-water single phase and the resistance-increasing principle of water phase are analyzed. Establishing the dual-phase multi-stage separation and resistance-increasing model, and verified by measuring the throttling pressure drop and oil-water volume fraction of the AICD, it is found that the composite type AICD has the effect of ICD and AICD at the same time, which can balance the production rate of each well section at the initial stage of production, delay the occurrence of bottom water coning. In the middle and later stages of production, water-blocking can be effectively increased to achieve water control and stable production.After structural sensitivity analysis, the influence law of various structural parameters on the water control performance of composite AICD was obtained. The simulation calculation results show that,compared with the existing swirl type AICD, composite AICD has higher sensitivity to moisture content,the water phase throttling pressure drop is increased by 4.5 times on average. The composite AICD is suitable for the entire stage of horizontal well production.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11172326 and 11502280)
文摘The effects of the micro-ramps on supersonic turbulent flow over a forward-facing step（FFS） was experimentally investigated in a supersonic low-noise wind tunnel at Mach number 3 using nano-tracer planar laser scattering（NPLS）and particle image velocimetry（PIV） techniques. High spatiotemporal resolution images and velocity fields of supersonic flow over the testing model were captured. The fine structures and their spatial evolutionary characteristics without and with the micro-ramps were revealed and compared. The large-scale structures generated by the micro-ramps can survive the downstream FFS flowfield. The micro-ramps control on the flow separation and the separation shock unsteadiness was investigated by PIV results. With the micro-ramps, the reduction in the range of the reversal flow zone in streamwise direction is 50% and the turbulence intensity is also reduced. Moreover, the reduction in the average separated region and in separation shock unsteadiness are 47% and 26%, respectively. The results indicate that the micro-ramps are effective in reducing the flow separation and the separation shock unsteadiness.
基金The project supported by the National Natural Science Foundations of China the LNM,Institute of Mechanics,Academia Sinica
文摘A new hybrid model, which is based on domain decomposition and proposed by the authors is used for calculating the flow around a circular cylinder at low and middle Keulegan-Carpenter numbers (Kc=2～18)respectively.The vortex motion patterns in asymmetric regime,single pair(or transverse)regime and double pair(or diagonal)regime are successfully simulated.The calculated drag and inertial force coefficients are in better agreement with experimental data than other recent computational results.
文摘Flow induced oscillation in a cavity and its suppression by means of acoustic excitation were studied both experimentally and numerically. In the experiment it was found that with the leading edge pure tone excitation at some frequencies and intensities. the flow-induced oscillation in the cavity could be greatly suppressed. Cavity flows both with and without acoustic excitation were studied by solving the 2-D time-dependent Reynolds averaged Navier Stokes equations using explicit predictor-corrector difference algorithm of MacCormack. Effects of turbulence were simulated via Cebeci-Smith turbulence mode with relaxation modification. The computational and experimental results are compared. and good agreement is obtained.
