Missile-borne short-range infrared detection(SIRD)technology is commonly used in military ground target detection.In complex battlefield environments,achieving precise strike on ground target is a challenging task.How...Missile-borne short-range infrared detection(SIRD)technology is commonly used in military ground target detection.In complex battlefield environments,achieving precise strike on ground target is a challenging task.However,real battlefield data is limited,and equivalent experiments are costly.Currently,there is a lack of comprehensive physical modeling and numerical simulation methods for SIRD.To this end,this study proposes a SIRD simulation framework incorporating full-link physical response,which is integrated through the radiative transfer layer,the sensor response layer,and the model-driven layer.In the radiative transfer layer,a coupled dynamic detection model is established to describe the external optical channel response of the SIRD system by combining the infrared radiation model and the geometric measurement model.In the sensor response layer,considering photoelectric conversion and signal processing,the internal signal response model of the SIRD system is established by a hybrid mode of parametric modeling and analog circuit analysis.In the model-driven layer,a cosimulation application based on a three-dimensional virtual environment is proposed to drive the full-link physical model,and a parallel ray tracing method is employed for real-time synchronous simulation.The proposed simulation framework can provide pixel-level signal output and is verified by the measured data.The evaluation results of the root mean square error(RMSE)and the Pearson correlation coefficient(PCC)show that the simulated data and the measured data achieve good consistency,and the evaluation results of the waveform eigenvalues indicate that the simulated signals exhibit low errors compared to the measured signals.The proposed simulation framework has the potential to acquire large sample datasets of SIRD under various complex battlefield environments and can provide an effective data source for SIRD application research.展开更多
In the ultra-deep strata of the Tarim Basin,the vertical growth process of strike-slip faults remains unclear,and the vertical distribution of fractured-cavity carbonate reservoirs is complex.This paper investigates t...In the ultra-deep strata of the Tarim Basin,the vertical growth process of strike-slip faults remains unclear,and the vertical distribution of fractured-cavity carbonate reservoirs is complex.This paper investigates the vertical growth process of strike-slip faults through field outcrop observations in the Keping area,interpretation of seismic data from the Fuman Oilfield,Tarim Basim,NW China,and structural physical simulation experiments.The results are obtained mainly in four aspects.First,field outcrops and ultra-deep seismic profiles indicate a three-layer structure within the strike-slip fault,consisting of fault core,fracture zone and primary rock.The fault core can be classified into three parts vertically:fracture-cavity unit,fault clay and breccia zone.The distribution of fracture-cavity units demonstrates a distinct pattern of vertical stratification,owing to the structural characteristics and growth process of the slip-strike fault.Second,the ultra-deep seismic profiles show multiple fracture-cavity units in the strike-slip fault zone.These units can be classified into four types:top fractured,middle connected,deep terminated,and intra-layer fractured.Third,structural physical simulation experiments and ultra-deep seismic data interpretation reveal that the strike-slip faults have evolved vertically in three stages:segmental rupture,vertical growth,and connection and extension.The particle image velocimetry detection demonstrates that the initial fracture of the fault zone occurred at the top or bottom and then evolved into cavities gradually along with the fault growth,accompanied by the emergence of new fractures in the middle part of the strata,which subsequently connected with the deep and shallow cavities to form a complete fault zone.Fourth,the ultra-deep carbonate strata primarily develop three types of fractured-cavity reservoirs:flower-shaped fracture,large and deep fault and staggered overlap.The first two types are larger in size with better reservoir conditions,suggesting a significant exploration potential.展开更多
The hot forging of large-scale P/M TiAl alloy billet deformation was investigated based on a joint application of Deform-3D-based numerical simulation and physical simulation techniques.The temperature dependence on t...The hot forging of large-scale P/M TiAl alloy billet deformation was investigated based on a joint application of Deform-3D-based numerical simulation and physical simulation techniques.The temperature dependence on the thermal and mechanical properties of the billet was considered and the optimum hot working temperature of packed TiAl alloy was 1150-1200 °C.Based on the simulation,the material flow and thermo mechanical field variables,such as stress,strain,and temperature distribution were obtained and the relationships of load—displacement and load—time were figured out.To verify the validity of the simulation results,the experiments were also carried out in a forging plant,and a pancake with diameter of 150 mm was obtained exhibiting a regular shape.展开更多
The contrast experiment of different stirring modes,which includes a new type of stirring-injection with the method of pulse and rotation,and the initial one-way stirring method,is done through physical simulation in ...The contrast experiment of different stirring modes,which includes a new type of stirring-injection with the method of pulse and rotation,and the initial one-way stirring method,is done through physical simulation in the laboratory.The stirring methods of pulse and rotation are of two kinds.One is pulsed and rotary stirrer with positive and opposite directions.The other is pulsed and rotary stirrer with rotation-stop-rotation.The results show that the stirring mode of pulse and rotation has better effects than the one-way stirring method.The specific effects are that the mixing time of the melting bath is apparently shortened,the number of grains involved in the liquid surface is increased,and the residence time of air bubble in water is doubled.展开更多
Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physical simulation method using gallium melt and fast speed photography. Flow morphology and its format...Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physical simulation method using gallium melt and fast speed photography. Flow morphology and its formation mechanism were obtained and discussed for thin-walled casting. The influences of magnetic field density on the filling ability, filling velocity and mold filling time have been studied. The differences in filling capability between gravity casting and casting under the traveling magnetic field have been compared. The results indicate that the mold filling ability of the gallium melt increases greatly under the condition of traveling magnetic field; the filling time is shortened from 18 s under gravity field to 3 s under the traveling magnetic field and average flow rate of the melt increases from 1.6 to 8.68 cm3/s; the change law of the cross-section morphology of the gallium melt during the mold filling is that at first, the cross-section area does not change, then it decreases gradually. When the front of the melt reaches the end of the mold cavity, the front melt will backfill the mold; the wider the width of mold cavity, the better the mold filling ability. The mold filling ability of gallium melt in mold with upper magnetic conductor is better than that without upper magnetic conductor.展开更多
The kinetics of ε-Cu particles dissolution in the matrix during welding of a copper-precipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness mea...The kinetics of ε-Cu particles dissolution in the matrix during welding of a copper-precipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness meas urement. The ε-Cu particles underwent a coarsening and part dissolution and then complete dissolution reaction as the peak temperature increased from 750 to 1 000℃, which resulted in the decrease in the number density of ε-Cu particles and hardness in the heat affected zone （HAZ）. The results can be used to understand the evolution of this transformation and a softening behavior of the HAZ during welding of this type of steel.展开更多
A physical model of molten slag granulation by rotary disk was developed based on the mechanism of New-tonian liquid granulation. For geometrical similarity, the radius ratio of model disk to the prototype disk was ch...A physical model of molten slag granulation by rotary disk was developed based on the mechanism of New-tonian liquid granulation. For geometrical similarity, the radius ratio of model disk to the prototype disk was chosen as 1 ： 1. For dynamic similarity, equality of Ohnesorge number between the model and the prototype was achieved firstly by compounding rosin and paraffin wax with mass ratio of 4 ~ 1 as simulation liquid of molten blast furnace （BF） slag, and the simulation material can satisfy the similarity of liquid solid transformation during falling in the medium; then equality of Reynolds number and Weber number was obtained by controlling the volumetric flow rate and the rotary speed, respectively. Model accuracy was verified by comparing the simulation data with the results re ported in literature, which showed good agreement with the calculation results of empirical equation and the actual molten BF slag granulation from the view point of particle size. Furthermore, influences of disk radius, rotary speed and liquid flow rate on granulation were discussed using the developed model, and the Kitamura equation was modi-fied according to the simulation data which can predict particle size more accurately. Using the modified equation, the operation parameters were predicted according to the flow rate of molten industrial BF slag.展开更多
Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mec...Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mechanism and development of outburst is to conduct the similar physical simulation. However, the similarity criteria and similar materials in outburst are the key factors which restrict the development of physical simulation. To solve those problems, this paper has established similarity criteria base on mechanics model, solid-fluid coupling model and energy model, and presented high similar materials. Combining with three groups of similar number, and considering similar mechanical parameters and deformation and failure regularity, the similarity criteria of outburst is determined on the basis of the energy model. According to those criteria, we put forward a similar material consists of pulverized coal, cement, sand, activated carbon, and water. The similar material has high compressive strength and the accordant characteristics with the raw coal, include density, porosity, adsorption, desorption. The new research is promising for preventing and controlling gas hazards in the future.展开更多
Direct quenching and tempering （DQ-T） of hot rolled steel section has been widely used in steel mill for the sake of improvement of mechanical properties and energy saving. Temperature history and microstructural ev...Direct quenching and tempering （DQ-T） of hot rolled steel section has been widely used in steel mill for the sake of improvement of mechanical properties and energy saving. Temperature history and microstructural evolution during hot rolling plays a major role in the properties of direct quenched and tempered products. The mathematical and physical modeling of hot forming processes is becoming a very important tool for design and development of required products as well as predicting the microstructure and the properties of the components. These models were mostly used to predict austenite grain size （AGS）, dynamic, recta-dynamic and static recrystallization in the rods immediately after hot rolling and prior to DQ process. The hot compression tests were carried out on 42CrMo4 steel in the temperature range of 900-1 100 ℃ and the strain rate range of 0. 05-1 s^-1 in order to study the high tempera- ture softening behavior of the steel. For the exact prediction of flow stress, the effective stress-effective strain curves were obtained from experiments under various conditions. On the basis of experimental results, the dynamic recrystallization fraction （DRX）, AGS, hot deformation and activation energy behavior were investigated. It was found that the calculated results were in good agreement with the experimental flow stress and microstructure of the steel for different conditions of hot deformation.展开更多
During the growth of the hot filament chemical vapor deposition （HFCVD） diamond films, numerical simulations in a 2-D mathematical model were employed to investigate the influence of various deposition parameters on...During the growth of the hot filament chemical vapor deposition （HFCVD） diamond films, numerical simulations in a 2-D mathematical model were employed to investigate the influence of various deposition parameters on the gas physical parameters, including the temperature, velocity and volume density of gas. It was found that, even in the case of optimized deposition parameters, the space distributions of gas parameters were heterogeneous due primarily to the thermal blockage come from the hot filaments and cryogenic pump effect arisen from the cold reactor wall. The distribution of volume density agreed well with the thermal round-flow phenomenon, one of the key obstacles to obtaining high growth rate in HFCVD process. In virtue of isothermal boundary with high temperature or adiabatic boundary condition of reactor wall, however, the thermal roundflow was profoundly reduced and as a consequence, the uniformity of gas physical parameters was considerably improved, as identified by the experimental films growth.展开更多
Simulation law and physical simulation were used to study the kinematic behavior of inclusions in electromagnetic separation. It was found that velocity of spherical non metallic particles shares different functions i...Simulation law and physical simulation were used to study the kinematic behavior of inclusions in electromagnetic separation. It was found that velocity of spherical non metallic particles shares different functions in different Reynolds number range. The function of spherical particle’s velocity has been got by confirming the relationship between Reynolds number and resistance coefficient when Reynolds number is 0.2 ～10. For non spherical particles, the moving behavior is influenced by shape and orientation while spherical coefficient has nothing to do with the velocity of irregular particles. The influence of orientation of cuboid particle on the electromagnetic expulsive force has been indicated by numerical computation. [展开更多
Real waves are multidirectional waves. In the present study, the calculation method for the wave maker driving signals for generating multidirectional wave groups in physical wave basin is proposed. Its validity is fi...Real waves are multidirectional waves. In the present study, the calculation method for the wave maker driving signals for generating multidirectional wave groups in physical wave basin is proposed. Its validity is first confirmed by a numerical model for which the incident boundary condition is determined by use of the proposed method. Then, the physical simulation of multidirectional wave groups is performed in laboratory wave basin. The experimental results show that multidirectional waves with expected wave groupiness, which includes not only its group height but also its group length, can be satisfactorily zenerated at the soecified oosition in the tphvsical wave basin.展开更多
A numerical model of flatfish cage is built based on the lumped mass method and the principle of rigid body kinematics. To validate the numerical model, a series of physical model tests are conducted in the wave flume...A numerical model of flatfish cage is built based on the lumped mass method and the principle of rigid body kinematics. To validate the numerical model, a series of physical model tests are conducted in the wave flume. The numerical results correspond well with the data sets from physical model test. The effect of weight of bottom frame, height of fish net and net shape on motion responses of fish cage and tension force on mooring lines is then analyzed. The results indicate that the vertical displacements of float collar and bottom frame decrease with the increase in the weight of bottom frame; the maximum tension force on mooring lines increases with the increasing weight of bottom frame. The inclination angles of float collar and bottom frame decrease with the increasing net height; the maximum tension force increases obviously with the increase of net height.展开更多
To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale co...To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.展开更多
The behavior of stress wave propagation in rock walls and the process of rock bursts were simulated by application tests of material similar to rock. Results show that 1) the attenuation characteristics of stress wave...The behavior of stress wave propagation in rock walls and the process of rock bursts were simulated by application tests of material similar to rock. Results show that 1) the attenuation characteristics of stress waves were related to the material proper-ties, stress waves attenuate more quickly in soft material and 2) when the explosion load was applied at the top of the roadway, the number and the length of the cracks increased with a decrease in the distance between the explosive point and roof of the roadway. When the distance was 280 mm, only some chips appeared near the source, when the distance was 210 mm, some small cracks started to appear near the road-rib and when the distance was reduced to 140 mm, larger cracks appeared at the road-rib. It can be concluded that, under a given stress the number of cracks is closely related to the intensity of stress waves. The cracks in the sur-rounding rock can be reduced by controlling the intensity of the stress waves and rock bursts can be avoided to some extent by pre-venting the formation of layered crack structures. A new experimental approach has been provided for studying rock bursts by using physical simulation.展开更多
For extra-low permeability reservoirs, with a permeability of about 0.3×10?3 μm2, fluid flow and production performance in cores were studied. A long core holder with a multi-location piezometric measurement was...For extra-low permeability reservoirs, with a permeability of about 0.3×10?3 μm2, fluid flow and production performance in cores were studied. A long core holder with a multi-location piezometric measurement was specially designed. An artificial long core, about 700 mm long and with a cross section of 45mm×45mm, was used. In the experiment, pressure distribution along the core can be measured in real time. Single phase flow in the core was investigated. Different modes of production in long cores were also simulated including natural depletion, water flooding, and advanced water flooding. Through physical simulation, flow parameters were collected and production characteristics in extra-low permeability cores were studied. From experimental results, it can be seen that fluid flow in extra-low permeability cores is different from that in high permeability cores. Transmission of pressure in extra-low permeability cores is very slow, and it needs a long time for the pressure to become stable. The distribution curve of pressure along the core is nonlinear and the production rate in extra-low permeability reservoirs decreases sharply. The development effects of different production modes in extra-low permeability cores were compared with one another. Among the production modes, advanced water flooding has much potential for effective development of extra-low permeability reservoirs. Natural depletion and conventional water flooding can also be used in early production periods. In addition, the countermeasures and some ideas especially for the potential development of extra-low permeability reservoirs are suggested.展开更多
A gate-all-around cylindrical （GAAC） transistor for sub-10nm scaling is proposed. The GAAC transistor device physics,TCAD simulation,and proposed fabrication procedure are reported for the first time. Among all othe...A gate-all-around cylindrical （GAAC） transistor for sub-10nm scaling is proposed. The GAAC transistor device physics,TCAD simulation,and proposed fabrication procedure are reported for the first time. Among all other novel FinFET devices, the gate-all-around cylindrical device can be particularly applied for reducing the problems of the conventional multi-gate FinFET and improving the device performance and the scale down capability. According to our simulation,the gate-all-around cylindrical device shows many benefits over conventional multi-gate FinFET, including gate-all- around rectangular （GAAR） devices. With gate-all-around cylindrical architecture,the transistor is controlled by an essen- tially infinite number of gates surrounding the entire cylinder-shaped channel. The electrical integrity within the channel is improved by reducing the leakage current due to the non-symmetrical field accumulation such as the corner effect. The proposed fabrication procedures for devices having GAAC device architecture are also discussed. The method is characterized by its simplicity and full compatibility with conventional planar CMOS technology.展开更多
The physiological structure of the upper respiratory tract is complex and varies with each individual,and the circulating air has turbulent performance.In this paper,based on computed tomography(CT)medical images publ...The physiological structure of the upper respiratory tract is complex and varies with each individual,and the circulating air has turbulent performance.In this paper,based on computed tomography(CT)medical images published online and the three-dimensional(3D)printing technology,a 3D model of the human upper respiratory tract was reconstructed and an experimental device of the upper respiratory tract was made.We implemented the respiratory experiment and measured the flow rate,and a scale-adaptive κ-ω model is applied for numerical simulation,the results are in good agreement.The flow field during respiratory was analyzed by coronal velocity cross section,vortex line and particle tracks.We found that the relatively strong shear effect happens at the areas of nasal valve and nasopharynx.In the middle and upper nasal tract,vortex line separation occurs and there is significant passage effect.The results indicate that SAS method is effective in studying upper respiratory airflow.展开更多
Most existing force feedback methods are still difficult to meet the requirements of real-time force calculation in virtual assembly and operation with complex objects. In addition, there is often an assumption that t...Most existing force feedback methods are still difficult to meet the requirements of real-time force calculation in virtual assembly and operation with complex objects. In addition, there is often an assumption that the controlled objects are completely flee and the target object is only completely fixed or flee, thus, the dynamics of the kinematic chain where the controlled objects are located are neglected during the physical simulation of the product manipulation with force feedback interaction. This paper proposes a physical simulation method of product assembly and operation manipulation based on statistically learned contact force prediction model and the coupling of force feedback and dynamics. In the proposed method, based on hidden Markov model （HMM） and local weighting learning （LWL）, contact force prediction model is constructed, which can estimate the contact force in real time during interaction. Based on computational load balance model, the computing resources are dynamically assigned and the dynamics integral step is optimized. In addition, smoothing process is performed to the force feedback on the synchronization points. Consequently, we can solve the coupling and synchronization problems of high-frequency feedback force servo. low-frequency dynamics solver servo and scene rendering servo, and realize highly stable and accurate force feedback in the physical simulation of product assembly and operation manipulation. This research proposes a physical simulation method of product assembly and operation manipulation.展开更多
Stress sensitivity is a very important index to understand the seepage characteristics of a reservoir.In this study,dedicated experiments and theoretical arguments based on the visualization of porous media are used t...Stress sensitivity is a very important index to understand the seepage characteristics of a reservoir.In this study,dedicated experiments and theoretical arguments based on the visualization of porous media are used to assess the effects of the fracture angle,spacing,and relevant elastic parameters on the principal value of the permeability tensor.The fracture apertures at different angles show different change rates,which influence the relative permeability for different sets of fractures.Furthermore,under the same pressure condition,the fractures with different angles show different degrees of deformation so that the principal value direction of permeability rotates.This phenomenon leads to a variation in the water seepage direction in typical water-injection applications,thereby hindering the expected exploitation effect of the original well network.Overall,the research findings in this paper can be used as guidance to improve the effectiveness of water injection exploitation in the oil field industry.展开更多
基金supported by the Foundation of Equipment Preresearch Area(Grant No.80919010303).
文摘Missile-borne short-range infrared detection(SIRD)technology is commonly used in military ground target detection.In complex battlefield environments,achieving precise strike on ground target is a challenging task.However,real battlefield data is limited,and equivalent experiments are costly.Currently,there is a lack of comprehensive physical modeling and numerical simulation methods for SIRD.To this end,this study proposes a SIRD simulation framework incorporating full-link physical response,which is integrated through the radiative transfer layer,the sensor response layer,and the model-driven layer.In the radiative transfer layer,a coupled dynamic detection model is established to describe the external optical channel response of the SIRD system by combining the infrared radiation model and the geometric measurement model.In the sensor response layer,considering photoelectric conversion and signal processing,the internal signal response model of the SIRD system is established by a hybrid mode of parametric modeling and analog circuit analysis.In the model-driven layer,a cosimulation application based on a three-dimensional virtual environment is proposed to drive the full-link physical model,and a parallel ray tracing method is employed for real-time synchronous simulation.The proposed simulation framework can provide pixel-level signal output and is verified by the measured data.The evaluation results of the root mean square error(RMSE)and the Pearson correlation coefficient(PCC)show that the simulated data and the measured data achieve good consistency,and the evaluation results of the waveform eigenvalues indicate that the simulated signals exhibit low errors compared to the measured signals.The proposed simulation framework has the potential to acquire large sample datasets of SIRD under various complex battlefield environments and can provide an effective data source for SIRD application research.
基金Supported by the National Natural Science Foundation of China(42362026)Key R&D Project of Xinjiang Uygur Autonomous Region(2024B01015).
文摘In the ultra-deep strata of the Tarim Basin,the vertical growth process of strike-slip faults remains unclear,and the vertical distribution of fractured-cavity carbonate reservoirs is complex.This paper investigates the vertical growth process of strike-slip faults through field outcrop observations in the Keping area,interpretation of seismic data from the Fuman Oilfield,Tarim Basim,NW China,and structural physical simulation experiments.The results are obtained mainly in four aspects.First,field outcrops and ultra-deep seismic profiles indicate a three-layer structure within the strike-slip fault,consisting of fault core,fracture zone and primary rock.The fault core can be classified into three parts vertically:fracture-cavity unit,fault clay and breccia zone.The distribution of fracture-cavity units demonstrates a distinct pattern of vertical stratification,owing to the structural characteristics and growth process of the slip-strike fault.Second,the ultra-deep seismic profiles show multiple fracture-cavity units in the strike-slip fault zone.These units can be classified into four types:top fractured,middle connected,deep terminated,and intra-layer fractured.Third,structural physical simulation experiments and ultra-deep seismic data interpretation reveal that the strike-slip faults have evolved vertically in three stages:segmental rupture,vertical growth,and connection and extension.The particle image velocimetry detection demonstrates that the initial fracture of the fault zone occurred at the top or bottom and then evolved into cavities gradually along with the fault growth,accompanied by the emergence of new fractures in the middle part of the strata,which subsequently connected with the deep and shallow cavities to form a complete fault zone.Fourth,the ultra-deep carbonate strata primarily develop three types of fractured-cavity reservoirs:flower-shaped fracture,large and deep fault and staggered overlap.The first two types are larger in size with better reservoir conditions,suggesting a significant exploration potential.
基金Project (2011CB605505) supported by the National Basic Research Program of ChinaProject (2011QNZT041) supported by the freedom explore Program of Central South University,ChinaProject (84088) supported by the and Postdoctoral Foundation Supported Project of Central South University,China
文摘The hot forging of large-scale P/M TiAl alloy billet deformation was investigated based on a joint application of Deform-3D-based numerical simulation and physical simulation techniques.The temperature dependence on the thermal and mechanical properties of the billet was considered and the optimum hot working temperature of packed TiAl alloy was 1150-1200 °C.Based on the simulation,the material flow and thermo mechanical field variables,such as stress,strain,and temperature distribution were obtained and the relationships of load—displacement and load—time were figured out.To verify the validity of the simulation results,the experiments were also carried out in a forging plant,and a pancake with diameter of 150 mm was obtained exhibiting a regular shape.
文摘The contrast experiment of different stirring modes,which includes a new type of stirring-injection with the method of pulse and rotation,and the initial one-way stirring method,is done through physical simulation in the laboratory.The stirring methods of pulse and rotation are of two kinds.One is pulsed and rotary stirrer with positive and opposite directions.The other is pulsed and rotary stirrer with rotation-stop-rotation.The results show that the stirring mode of pulse and rotation has better effects than the one-way stirring method.The specific effects are that the mixing time of the melting bath is apparently shortened,the number of grains involved in the liquid surface is increased,and the residence time of air bubble in water is doubled.
文摘Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physical simulation method using gallium melt and fast speed photography. Flow morphology and its formation mechanism were obtained and discussed for thin-walled casting. The influences of magnetic field density on the filling ability, filling velocity and mold filling time have been studied. The differences in filling capability between gravity casting and casting under the traveling magnetic field have been compared. The results indicate that the mold filling ability of the gallium melt increases greatly under the condition of traveling magnetic field; the filling time is shortened from 18 s under gravity field to 3 s under the traveling magnetic field and average flow rate of the melt increases from 1.6 to 8.68 cm3/s; the change law of the cross-section morphology of the gallium melt during the mold filling is that at first, the cross-section area does not change, then it decreases gradually. When the front of the melt reaches the end of the mold cavity, the front melt will backfill the mold; the wider the width of mold cavity, the better the mold filling ability. The mold filling ability of gallium melt in mold with upper magnetic conductor is better than that without upper magnetic conductor.
文摘The kinetics of ε-Cu particles dissolution in the matrix during welding of a copper-precipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness meas urement. The ε-Cu particles underwent a coarsening and part dissolution and then complete dissolution reaction as the peak temperature increased from 750 to 1 000℃, which resulted in the decrease in the number density of ε-Cu particles and hardness in the heat affected zone （HAZ）. The results can be used to understand the evolution of this transformation and a softening behavior of the HAZ during welding of this type of steel.
基金Sponsored by China Postdoctoral Science Foundation(20110491517)Fundamental Research Funds for Central Universities of China(N100402012)Doctor Start-Up Fund of Natural Science Foundation of Liaoning Province of China(201120004)
文摘A physical model of molten slag granulation by rotary disk was developed based on the mechanism of New-tonian liquid granulation. For geometrical similarity, the radius ratio of model disk to the prototype disk was chosen as 1 ： 1. For dynamic similarity, equality of Ohnesorge number between the model and the prototype was achieved firstly by compounding rosin and paraffin wax with mass ratio of 4 ~ 1 as simulation liquid of molten blast furnace （BF） slag, and the simulation material can satisfy the similarity of liquid solid transformation during falling in the medium; then equality of Reynolds number and Weber number was obtained by controlling the volumetric flow rate and the rotary speed, respectively. Model accuracy was verified by comparing the simulation data with the results re ported in literature, which showed good agreement with the calculation results of empirical equation and the actual molten BF slag granulation from the view point of particle size. Furthermore, influences of disk radius, rotary speed and liquid flow rate on granulation were discussed using the developed model, and the Kitamura equation was modi-fied according to the simulation data which can predict particle size more accurately. Using the modified equation, the operation parameters were predicted according to the flow rate of molten industrial BF slag.
基金Acknowledgements This work was financially supported by the National Key Research and Development Program （2016YFC0801402-4）, the National Natural Science Foundation of China （51374236, 51574280）, Chongqing Frontiers and Application- based Research Program （cstc2015jcyjBX0076）. Meanwhile, the author would like to thank the reviewers of this paper for their constructive comments and suggestions to improve the publication.
文摘Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mechanism and development of outburst is to conduct the similar physical simulation. However, the similarity criteria and similar materials in outburst are the key factors which restrict the development of physical simulation. To solve those problems, this paper has established similarity criteria base on mechanics model, solid-fluid coupling model and energy model, and presented high similar materials. Combining with three groups of similar number, and considering similar mechanical parameters and deformation and failure regularity, the similarity criteria of outburst is determined on the basis of the energy model. According to those criteria, we put forward a similar material consists of pulverized coal, cement, sand, activated carbon, and water. The similar material has high compressive strength and the accordant characteristics with the raw coal, include density, porosity, adsorption, desorption. The new research is promising for preventing and controlling gas hazards in the future.
文摘Direct quenching and tempering （DQ-T） of hot rolled steel section has been widely used in steel mill for the sake of improvement of mechanical properties and energy saving. Temperature history and microstructural evolution during hot rolling plays a major role in the properties of direct quenched and tempered products. The mathematical and physical modeling of hot forming processes is becoming a very important tool for design and development of required products as well as predicting the microstructure and the properties of the components. These models were mostly used to predict austenite grain size （AGS）, dynamic, recta-dynamic and static recrystallization in the rods immediately after hot rolling and prior to DQ process. The hot compression tests were carried out on 42CrMo4 steel in the temperature range of 900-1 100 ℃ and the strain rate range of 0. 05-1 s^-1 in order to study the high tempera- ture softening behavior of the steel. For the exact prediction of flow stress, the effective stress-effective strain curves were obtained from experiments under various conditions. On the basis of experimental results, the dynamic recrystallization fraction （DRX）, AGS, hot deformation and activation energy behavior were investigated. It was found that the calculated results were in good agreement with the experimental flow stress and microstructure of the steel for different conditions of hot deformation.
基金This work was partially supported by the National Natural Science Foundation of China （NSFC） under Contract No. 59292800 the Science and Technology Committee of Liaoning Province.
文摘During the growth of the hot filament chemical vapor deposition （HFCVD） diamond films, numerical simulations in a 2-D mathematical model were employed to investigate the influence of various deposition parameters on the gas physical parameters, including the temperature, velocity and volume density of gas. It was found that, even in the case of optimized deposition parameters, the space distributions of gas parameters were heterogeneous due primarily to the thermal blockage come from the hot filaments and cryogenic pump effect arisen from the cold reactor wall. The distribution of volume density agreed well with the thermal round-flow phenomenon, one of the key obstacles to obtaining high growth rate in HFCVD process. In virtue of isothermal boundary with high temperature or adiabatic boundary condition of reactor wall, however, the thermal roundflow was profoundly reduced and as a consequence, the uniformity of gas physical parameters was considerably improved, as identified by the experimental films growth.
文摘Simulation law and physical simulation were used to study the kinematic behavior of inclusions in electromagnetic separation. It was found that velocity of spherical non metallic particles shares different functions in different Reynolds number range. The function of spherical particle’s velocity has been got by confirming the relationship between Reynolds number and resistance coefficient when Reynolds number is 0.2 ～10. For non spherical particles, the moving behavior is influenced by shape and orientation while spherical coefficient has nothing to do with the velocity of irregular particles. The influence of orientation of cuboid particle on the electromagnetic expulsive force has been indicated by numerical computation. [
基金supported by the National Natural Science Foundation of China (Grant Nos. 51079023 and 50921001)the Program for New Century Excellent Talents in University (Grant No. NCET-05-0282)
文摘Real waves are multidirectional waves. In the present study, the calculation method for the wave maker driving signals for generating multidirectional wave groups in physical wave basin is proposed. Its validity is first confirmed by a numerical model for which the incident boundary condition is determined by use of the proposed method. Then, the physical simulation of multidirectional wave groups is performed in laboratory wave basin. The experimental results show that multidirectional waves with expected wave groupiness, which includes not only its group height but also its group length, can be satisfactorily zenerated at the soecified oosition in the tphvsical wave basin.
基金supported by the National Natural Science Foundation of China(Grant Nos.51109187,51239002 and 51221961the Project form Zhoushan Science and Technology Bureau(Grant No.2013C41002)
文摘A numerical model of flatfish cage is built based on the lumped mass method and the principle of rigid body kinematics. To validate the numerical model, a series of physical model tests are conducted in the wave flume. The numerical results correspond well with the data sets from physical model test. The effect of weight of bottom frame, height of fish net and net shape on motion responses of fish cage and tension force on mooring lines is then analyzed. The results indicate that the vertical displacements of float collar and bottom frame decrease with the increase in the weight of bottom frame; the maximum tension force on mooring lines increases with the increasing weight of bottom frame. The inclination angles of float collar and bottom frame decrease with the increasing net height; the maximum tension force increases obviously with the increase of net height.
基金supported by the National Key R&D Program of China(Grant No.2018YFC1405900)the Major Projects of National Science and Technology(Grant Nos.2016ZX05011-002,2016ZX05027-002-005)+3 种基金the National Natural Science Foundation of China(Grant No.41806073)the Natural Science Foundation of Shandong Province(Grant No.ZR2017BD014)Shandong Provincial Key Laboratory of Depositional Mineralization and Sedimentary Minerals,Shandong University of Science and Technology(Grant No.DMSM2017042)the Fundamental Research Funds for the Central Universities(Grant No.201964016)
文摘To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.
基金Projects 50490270 and 50634050 supported by the National Natural Science Foundation of China2007CB209400 by the National Basic Research Program of China2006A039 by the Youth Scientific Research Foundation of China University of Mining & Technology
文摘The behavior of stress wave propagation in rock walls and the process of rock bursts were simulated by application tests of material similar to rock. Results show that 1) the attenuation characteristics of stress waves were related to the material proper-ties, stress waves attenuate more quickly in soft material and 2) when the explosion load was applied at the top of the roadway, the number and the length of the cracks increased with a decrease in the distance between the explosive point and roof of the roadway. When the distance was 280 mm, only some chips appeared near the source, when the distance was 210 mm, some small cracks started to appear near the road-rib and when the distance was reduced to 140 mm, larger cracks appeared at the road-rib. It can be concluded that, under a given stress the number of cracks is closely related to the intensity of stress waves. The cracks in the sur-rounding rock can be reduced by controlling the intensity of the stress waves and rock bursts can be avoided to some extent by pre-venting the formation of layered crack structures. A new experimental approach has been provided for studying rock bursts by using physical simulation.
基金supported by China National Program on Key Basic Research Project (973 Program) (Grant No. 2006CB705805)National Key Scientific and Technological Project (Grant No. 2008ZX05009-004)
文摘For extra-low permeability reservoirs, with a permeability of about 0.3×10?3 μm2, fluid flow and production performance in cores were studied. A long core holder with a multi-location piezometric measurement was specially designed. An artificial long core, about 700 mm long and with a cross section of 45mm×45mm, was used. In the experiment, pressure distribution along the core can be measured in real time. Single phase flow in the core was investigated. Different modes of production in long cores were also simulated including natural depletion, water flooding, and advanced water flooding. Through physical simulation, flow parameters were collected and production characteristics in extra-low permeability cores were studied. From experimental results, it can be seen that fluid flow in extra-low permeability cores is different from that in high permeability cores. Transmission of pressure in extra-low permeability cores is very slow, and it needs a long time for the pressure to become stable. The distribution curve of pressure along the core is nonlinear and the production rate in extra-low permeability reservoirs decreases sharply. The development effects of different production modes in extra-low permeability cores were compared with one another. Among the production modes, advanced water flooding has much potential for effective development of extra-low permeability reservoirs. Natural depletion and conventional water flooding can also be used in early production periods. In addition, the countermeasures and some ideas especially for the potential development of extra-low permeability reservoirs are suggested.
文摘A gate-all-around cylindrical （GAAC） transistor for sub-10nm scaling is proposed. The GAAC transistor device physics,TCAD simulation,and proposed fabrication procedure are reported for the first time. Among all other novel FinFET devices, the gate-all-around cylindrical device can be particularly applied for reducing the problems of the conventional multi-gate FinFET and improving the device performance and the scale down capability. According to our simulation,the gate-all-around cylindrical device shows many benefits over conventional multi-gate FinFET, including gate-all- around rectangular （GAAR） devices. With gate-all-around cylindrical architecture,the transistor is controlled by an essen- tially infinite number of gates surrounding the entire cylinder-shaped channel. The electrical integrity within the channel is improved by reducing the leakage current due to the non-symmetrical field accumulation such as the corner effect. The proposed fabrication procedures for devices having GAAC device architecture are also discussed. The method is characterized by its simplicity and full compatibility with conventional planar CMOS technology.
基金supported by the Fundamental Research Funds for the Central Universities of China (Grant 17LGJC41)
文摘The physiological structure of the upper respiratory tract is complex and varies with each individual,and the circulating air has turbulent performance.In this paper,based on computed tomography(CT)medical images published online and the three-dimensional(3D)printing technology,a 3D model of the human upper respiratory tract was reconstructed and an experimental device of the upper respiratory tract was made.We implemented the respiratory experiment and measured the flow rate,and a scale-adaptive κ-ω model is applied for numerical simulation,the results are in good agreement.The flow field during respiratory was analyzed by coronal velocity cross section,vortex line and particle tracks.We found that the relatively strong shear effect happens at the areas of nasal valve and nasopharynx.In the middle and upper nasal tract,vortex line separation occurs and there is significant passage effect.The results indicate that SAS method is effective in studying upper respiratory airflow.
基金Supported by National Natural Science Foundation of China(51475418)National Basic Research 973 Program of China(2011CB706503)Science Fund for Creative Research Groups of National Natural Science Foundation of China(51221004)
文摘Most existing force feedback methods are still difficult to meet the requirements of real-time force calculation in virtual assembly and operation with complex objects. In addition, there is often an assumption that the controlled objects are completely flee and the target object is only completely fixed or flee, thus, the dynamics of the kinematic chain where the controlled objects are located are neglected during the physical simulation of the product manipulation with force feedback interaction. This paper proposes a physical simulation method of product assembly and operation manipulation based on statistically learned contact force prediction model and the coupling of force feedback and dynamics. In the proposed method, based on hidden Markov model （HMM） and local weighting learning （LWL）, contact force prediction model is constructed, which can estimate the contact force in real time during interaction. Based on computational load balance model, the computing resources are dynamically assigned and the dynamics integral step is optimized. In addition, smoothing process is performed to the force feedback on the synchronization points. Consequently, we can solve the coupling and synchronization problems of high-frequency feedback force servo. low-frequency dynamics solver servo and scene rendering servo, and realize highly stable and accurate force feedback in the physical simulation of product assembly and operation manipulation. This research proposes a physical simulation method of product assembly and operation manipulation.
基金This work is financially supported by the National Natural Science Foundation Project(No.51374222)National Major Project(No.2017ZX05032004-002)+2 种基金the National Key Basic Research&Development Program(No.2015CB250905)CNPC’s Major Scientific and Technological Project(No.2017E-0405)SINOPEC Major Scientific Research Project(No.P18049-1).
文摘Stress sensitivity is a very important index to understand the seepage characteristics of a reservoir.In this study,dedicated experiments and theoretical arguments based on the visualization of porous media are used to assess the effects of the fracture angle,spacing,and relevant elastic parameters on the principal value of the permeability tensor.The fracture apertures at different angles show different change rates,which influence the relative permeability for different sets of fractures.Furthermore,under the same pressure condition,the fractures with different angles show different degrees of deformation so that the principal value direction of permeability rotates.This phenomenon leads to a variation in the water seepage direction in typical water-injection applications,thereby hindering the expected exploitation effect of the original well network.Overall,the research findings in this paper can be used as guidance to improve the effectiveness of water injection exploitation in the oil field industry.
