Multi-layer riveted structures are widely applied to aircraft.During the service,cracks may appear within these structures due to stress concentration of the riveted holes.The guided wave monitoring has been proved to...Multi-layer riveted structures are widely applied to aircraft.During the service,cracks may appear within these structures due to stress concentration of the riveted holes.The guided wave monitoring has been proved to be an effective tool to deal with this problem.However,there is a lack of understanding of the wave propagation process across such kinds of structures.This study proposes a piezoelectric guided wave simulation method to reveal the propagation of guided waves in multi-layer riveted structures.Effects of pretension force,friction coefficient,and cracks that might influence wave characteristics are studied.The guided wave simulation data is compared with the experimental results and the results verify the simulation model.Then the guided wave propagation in a more complex long-beam butt joint structure is further simulated.展开更多
Self-piercing riveting(SPR)has been widely used in automobile industry,and the strength prediction of SPR joints always attracts the attention of researchers.In this work,a prediction method of the cross-tension stren...Self-piercing riveting(SPR)has been widely used in automobile industry,and the strength prediction of SPR joints always attracts the attention of researchers.In this work,a prediction method of the cross-tension strength of SPR joints was proposed on the basis of finite element(FE)simulation and extreme gradient boosting decision tree(XGBoost)algorithm.An FE model of SPR process was established to simulate the plastic deformations of rivet and substrate materials and verified in terms of cross-sectional dimensions of SPR joints.The residual mechanical field from SPR process simulation was imported into a 2D FE model for the cross-tension testing simulation of SPR joints,and cross-tension strengths from FE simulation show a good consistence with the experiment result.Based on the verified FE model,the mechanical properties and thickness of substrate materials were varied and then used for FE simulation to obtain cross-tension strengths of a number of SPR joints,which were used to train the regression model based on the XGBoost algorithm in order to achieve prediction for cross-tension strength of SPR joints.Results show that the cross-tension strengths of SPR steel/aluminum joints could be successfully predicted by the XGBoost regression model with a respective error less than 7.6%compared to experimental values.展开更多
The concave die design of self-pierce riveting(SPR) is of critical importance for product quality. The optimization of concave die parameters based on orthogonal test is proposed to explore the relationship between se...The concave die design of self-pierce riveting(SPR) is of critical importance for product quality. The optimization of concave die parameters based on orthogonal test is proposed to explore the relationship between self-pierce riveted joint quality and die parameters. There are nine independent die parameter factors in orthogonal test and each factor has 4 levels. In order to evaluate the interlock and neck thickness, we carry out numerical simulations by the software DEFORM-2D. Then, the primary and secondary factors that affect the joint quality have been found out by means of range analysis. Finally, an optimization scheme is brought forward to design concave die in SPR process, which indicates that the joint has higher quality than that of former orthogonal tests.This work can be extended by a detailed mechanical and fatigue analysis for the joint quality of SPR process.展开更多
Self-piercing riveting(SPR)is a cold forming technique used to fasten together two or more sheets of materials with a rivet without the need to predrill a hole.The application of SPR in the automotive sector has becom...Self-piercing riveting(SPR)is a cold forming technique used to fasten together two or more sheets of materials with a rivet without the need to predrill a hole.The application of SPR in the automotive sector has become increasingly popular mainly due to the growing use of lightweight materials in transportation applications.However,SPR joining of these advanced light materials remains a challenge as these materials often lack a good combination of high strength and ductility to resist the large plastic deformation induced by the SPR process.In this paper,SPR joints of advanced materials and their corresponding failure mechanisms are discussed,aiming to provide the foundation for future improvement of SPR joint quality.This paper is divided into three major sections:1)joint failures focusing on joint defects originated from the SPR process and joint failure modes under different mechanical loading conditions,2)joint corrosion issues,and 3)joint optimisation via process parameters and advanced techniques.展开更多
In this paper,self-piercing riveting(SPR)and friction self-piercing riveting(F-SPR)processes were employed to join aluminum alloy AA5182-O sheets.Parallel studies were carried out to compare the two processes in terms...In this paper,self-piercing riveting(SPR)and friction self-piercing riveting(F-SPR)processes were employed to join aluminum alloy AA5182-O sheets.Parallel studies were carried out to compare the two processes in terms of joint macrogeometry,tooling force,microhardness,quasi-static mechanical performance,and fatigue behavior.The results indicate that the F-SPR process formed both rivet–sheet interlocking and sheet–sheet solid-state bonding,whereas the SPR process only contained rivet–sheet interlocking.For the same rivet flaring,the F-SPR process required 63%less tooling force than the SPR process because of the softening effect of frictional heat and the lower rivet hardness of F-SPR.The decrease in the switch depth of the F-SPR resulted in more hardening of the aluminum alloy surrounding the rivet.The higher hardness of aluminum and formation of solid-state bonding enhanced the F-SPR joint stiffness under lap-shear loading,which contributed to the higher quasi-static lap-shear strength and longer fatigue life compared to those of the SPR joints.展开更多
A new testing methodology was developed to quantitively study galvanic corrosion of AZ31B and thermoset carbon-fiber–reinforced polymer spot-joined by a friction self-piercing riveting process.Pre-defined areas of AZ...A new testing methodology was developed to quantitively study galvanic corrosion of AZ31B and thermoset carbon-fiber–reinforced polymer spot-joined by a friction self-piercing riveting process.Pre-defined areas of AZ31B in the joint were exposed in 0.1 M NaCl solution over time.Massive galvanic corrosion of AZ31B was observed as exposure time increased.The measured volume loss was converted into corrosion current that was at least 48 times greater than the corrosion current of AZ31B without galvanic coupling.Ninety percent of the mechanical joint integrity was retained for corroded F-SPR joints to 200 h and then decreased because of the massive volume loss of AZ31B。展开更多
Friction self-piercing riveting(F-SPR)process based on a pip die has been invented to solve the cracking problems in riveting high-strength and low-ductility light metals,such as magnesium alloys,cast aluminum,and 7 s...Friction self-piercing riveting(F-SPR)process based on a pip die has been invented to solve the cracking problems in riveting high-strength and low-ductility light metals,such as magnesium alloys,cast aluminum,and 7 series aluminum alloys.In this paper,in order to solve quality issues caused by the misalignment between rivet and pip-die in F-SPR,a flat-die based F-SPR process was proposed and employed to join 1.27 mm-thick AA6061-T6 to 3 mm-thick AZ31B.The results indicate that a 1.0 mm die distance is effective to avoid rivet upset and insufficient flaring.As the feed rate increases,the heat input in the whole process decreases,resulting in a larger riveting force,which in turn increases both the bottom thickness and interlock amount.Besides,solid-state bonding,including Al-Mg intermetallic compounds(IMCs),Al-Mg mechanical mixture,and Al-Fe atom interdiffusion was observed at the joint interfaces.The upper Al layer was softened,but the lower Mg layer was hardened,and both sheets exhibited a narrowed affected region with the increase of feed rate,while the rivet hardness shows no obvious change.Three fracture modes appeared accompanying the variations in lap-shear strength and energy absorption as the feed rate increased from 2 mm/s to 8 mm/s.Finally,the F-SPR process using a flat die was compared to those using a pip die and a flat bottom die to show the advantage of flat die on coping with the misalignment problem.展开更多
A recently developed friction self-piercing riveting(F-SPR)technique based on the combination of fric-tion stir processing and riveting has been reported to possess both solid-state bonding and mechanical fastening ch...A recently developed friction self-piercing riveting(F-SPR)technique based on the combination of fric-tion stir processing and riveting has been reported to possess both solid-state bonding and mechanical fastening characteristics.However,there is still a lack of quantitative understanding of the hybrid en-hancement mechanism,hindering its engineering application.To fill in this gap,the current research investigated the microstructure evolution,microhardness distribution,and miniature-tensile performance of the aluminum alloy AA7075-T6 F-SPR joints by experiments.An accurate numerical simulation model was established to quantitatively evaluate the individual contributions of microstructure,local bonding strength,and macro interlocking to the performance of the joint,which could well explain the experi-mental results.It was found that due to the friction stirring of the rivet,solid-state bonding driven by dynamic recrystallization is realized between the trapped aluminum in the rivet cavity and the bottom aluminum sheet.The solid-state bonding zone has 75%yield strength,81%ultimate tensile strength,and 106%elongation compared to the base material.This solid-state bonding enables the internal interlock-ing between the trapped aluminum and the rivet to withstand the additional load,which forms a novel dual-interlock fastening mechanism and increases the peak cross-tension force by 14.3%compared to the single-interlock joint.展开更多
Carbon fiber reinforced polymer(CFRP) and AZ31B Mg alloy were joined by the friction self-piercing riveting(F-SPR) with different steel rivet shank sizes. With the increase of rivet shank size, lap shear fracture load...Carbon fiber reinforced polymer(CFRP) and AZ31B Mg alloy were joined by the friction self-piercing riveting(F-SPR) with different steel rivet shank sizes. With the increase of rivet shank size, lap shear fracture load and mechanical interlock distance increased. Ultrafine grains were formed at the joint in AZ31B as a result of dynamic recrystallization, which contributed to the higher hardness. Fatigue life of the CFRP-AZ31B joint was studied at various peak loads of 0.5, 1, 2, and 3 kN and compared with the resistance spot welded AZ31B-AZ31B from the open literature. The fatigue performance was better at higher peak load(>2 kN) and comparable to that of resistance spot welding of AZ31B to AZ31B at lower peak loads(<1 kN). From fractography, the crack initiation for lower peak load(<1 kN) case was observed at the fretting positions on the top and bottom surfaces of AZ31B sheet. When peak load was increased, fretting between the rivet and the top of AZ31B became more dominant to initiate a crack during fatigue testing.展开更多
The application of magnesium alloys to automobiles is increasing due to their superior specific strength and specific stiffness.In this study,an upper sheet of AZ31 magnesium alloy and a lower sheet of cold-rolled ste...The application of magnesium alloys to automobiles is increasing due to their superior specific strength and specific stiffness.In this study,an upper sheet of AZ31 magnesium alloy and a lower sheet of cold-rolled steel were joined by self-piercing riveting(SPR),a method commonly used to join automotive panels.A cross-shaped specimen was fabricated with a punching force of 35 kN,which exhibited the best joint strength for the SPR joint specimen geometry.Monotonic and fatigue strengths were evaluated using cross-shaped specimens at loading angles of 0°,45°,and 90°.The load amplitude corresponding to the fatigue endurance limit was assumed to be at 106 cycles,and the fatigue ratios(=fatigue endurance limit/static strength)at the loading angles of 0°,45°,and 90°are 22%,13%,and 9%,respectively.For all three loading angle specimens,fatigue cracks initiated at the triple point where the rivet shank,the upper sheet and the lower sheet are in contact with each other,with the cracks propagating through the thickness of the upper sheet and ultimately leading to fracture.The fatigue lifetimes were evaluated through the von-Mises stress,maximum principal stress,and equivalent stress intensity factor.It was found that the fatigue lifetimes could be evaluated most appropriately through the maximum principal stress.展开更多
Friction self-piercing riveting(F-SPR)is an emerging technique for low ductility materials joining,which creates a mechanical and solid-state hybrid joint with a semi-hollow rivet.The severe plastic deformation of wor...Friction self-piercing riveting(F-SPR)is an emerging technique for low ductility materials joining,which creates a mechanical and solid-state hybrid joint with a semi-hollow rivet.The severe plastic deformation of work materials and localized elevated temperatures during the F-SPR process yield complex and heterogeneous microstructures.The cut-off action of the work materials by the rivet further complicates the material flow during joint formation.This study employed the F-SPR process to join AA7075-T6 aluminum alloy sheets and systematically investigated the microstructural evolutions using electron backscatter diffraction(EBSD)techniques.The results suggested that as the base material approached the rivet,grains were deformed and recrystallized,forming two distinct fine grain zones(FGZs)surrounding the rivet and in the rivet cavity,re s pectively.Solid-state bonding of aluminum sheets occurred in the FGZs.The formation of FGZ outside the rivet is due to dynamic recrystallization(DRX)triggered by the sliding-to-sticking transition at the rivet/sheet interface.The FGZ in the rivet cavity was caused by the rotation of the trapped aluminum,which created a sticking affected zone at the trapped aluminum/lower sheet interface and led to DRX.Strain rate gradient in the trapped aluminum drove the further expansion of the sticking affected zone and resulted in grain refinement in a larger span.展开更多
文摘Multi-layer riveted structures are widely applied to aircraft.During the service,cracks may appear within these structures due to stress concentration of the riveted holes.The guided wave monitoring has been proved to be an effective tool to deal with this problem.However,there is a lack of understanding of the wave propagation process across such kinds of structures.This study proposes a piezoelectric guided wave simulation method to reveal the propagation of guided waves in multi-layer riveted structures.Effects of pretension force,friction coefficient,and cracks that might influence wave characteristics are studied.The guided wave simulation data is compared with the experimental results and the results verify the simulation model.Then the guided wave propagation in a more complex long-beam butt joint structure is further simulated.
基金Supported by National Natural Science Foundation of China(Grant No.51805375).
文摘Self-piercing riveting(SPR)has been widely used in automobile industry,and the strength prediction of SPR joints always attracts the attention of researchers.In this work,a prediction method of the cross-tension strength of SPR joints was proposed on the basis of finite element(FE)simulation and extreme gradient boosting decision tree(XGBoost)algorithm.An FE model of SPR process was established to simulate the plastic deformations of rivet and substrate materials and verified in terms of cross-sectional dimensions of SPR joints.The residual mechanical field from SPR process simulation was imported into a 2D FE model for the cross-tension testing simulation of SPR joints,and cross-tension strengths from FE simulation show a good consistence with the experiment result.Based on the verified FE model,the mechanical properties and thickness of substrate materials were varied and then used for FE simulation to obtain cross-tension strengths of a number of SPR joints,which were used to train the regression model based on the XGBoost algorithm in order to achieve prediction for cross-tension strength of SPR joints.Results show that the cross-tension strengths of SPR steel/aluminum joints could be successfully predicted by the XGBoost regression model with a respective error less than 7.6%compared to experimental values.
基金the National Natural Science Foundation of China(No.51375282)the China Postdoctoral Science Foundation(No.2012T50621)the Open Fund of Shanghai Key Laboratory of Digital Manufacture for Thin-walled Structures(No.2011003)
文摘The concave die design of self-pierce riveting(SPR) is of critical importance for product quality. The optimization of concave die parameters based on orthogonal test is proposed to explore the relationship between self-pierce riveted joint quality and die parameters. There are nine independent die parameter factors in orthogonal test and each factor has 4 levels. In order to evaluate the interlock and neck thickness, we carry out numerical simulations by the software DEFORM-2D. Then, the primary and secondary factors that affect the joint quality have been found out by means of range analysis. Finally, an optimization scheme is brought forward to design concave die in SPR process, which indicates that the joint has higher quality than that of former orthogonal tests.This work can be extended by a detailed mechanical and fatigue analysis for the joint quality of SPR process.
文摘Self-piercing riveting(SPR)is a cold forming technique used to fasten together two or more sheets of materials with a rivet without the need to predrill a hole.The application of SPR in the automotive sector has become increasingly popular mainly due to the growing use of lightweight materials in transportation applications.However,SPR joining of these advanced light materials remains a challenge as these materials often lack a good combination of high strength and ductility to resist the large plastic deformation induced by the SPR process.In this paper,SPR joints of advanced materials and their corresponding failure mechanisms are discussed,aiming to provide the foundation for future improvement of SPR joint quality.This paper is divided into three major sections:1)joint failures focusing on joint defects originated from the SPR process and joint failure modes under different mechanical loading conditions,2)joint corrosion issues,and 3)joint optimisation via process parameters and advanced techniques.
基金The authors would like to acknowledge the financial support of the National Natural Science Foundation of China(52025058 and U1764251)the National Key Research and Development Program of China(2016YFB0101606-8).
文摘In this paper,self-piercing riveting(SPR)and friction self-piercing riveting(F-SPR)processes were employed to join aluminum alloy AA5182-O sheets.Parallel studies were carried out to compare the two processes in terms of joint macrogeometry,tooling force,microhardness,quasi-static mechanical performance,and fatigue behavior.The results indicate that the F-SPR process formed both rivet–sheet interlocking and sheet–sheet solid-state bonding,whereas the SPR process only contained rivet–sheet interlocking.For the same rivet flaring,the F-SPR process required 63%less tooling force than the SPR process because of the softening effect of frictional heat and the lower rivet hardness of F-SPR.The decrease in the switch depth of the F-SPR resulted in more hardening of the aluminum alloy surrounding the rivet.The higher hardness of aluminum and formation of solid-state bonding enhanced the F-SPR joint stiffness under lap-shear loading,which contributed to the higher quasi-static lap-shear strength and longer fatigue life compared to those of the SPR joints.
基金financially sponsored by the US Department Energy Vehicle Technologies Office, as part of the Joining Core Programmanaged by UT-Battelle LLC for the US Department of Energy under Contract DE-AC05-00OR22725。
文摘A new testing methodology was developed to quantitively study galvanic corrosion of AZ31B and thermoset carbon-fiber–reinforced polymer spot-joined by a friction self-piercing riveting process.Pre-defined areas of AZ31B in the joint were exposed in 0.1 M NaCl solution over time.Massive galvanic corrosion of AZ31B was observed as exposure time increased.The measured volume loss was converted into corrosion current that was at least 48 times greater than the corrosion current of AZ31B without galvanic coupling.Ninety percent of the mechanical joint integrity was retained for corroded F-SPR joints to 200 h and then decreased because of the massive volume loss of AZ31B。
基金financial support of the National Natural Science Foundation of China(Grant Nos.52025058 and U1764251)。
文摘Friction self-piercing riveting(F-SPR)process based on a pip die has been invented to solve the cracking problems in riveting high-strength and low-ductility light metals,such as magnesium alloys,cast aluminum,and 7 series aluminum alloys.In this paper,in order to solve quality issues caused by the misalignment between rivet and pip-die in F-SPR,a flat-die based F-SPR process was proposed and employed to join 1.27 mm-thick AA6061-T6 to 3 mm-thick AZ31B.The results indicate that a 1.0 mm die distance is effective to avoid rivet upset and insufficient flaring.As the feed rate increases,the heat input in the whole process decreases,resulting in a larger riveting force,which in turn increases both the bottom thickness and interlock amount.Besides,solid-state bonding,including Al-Mg intermetallic compounds(IMCs),Al-Mg mechanical mixture,and Al-Fe atom interdiffusion was observed at the joint interfaces.The upper Al layer was softened,but the lower Mg layer was hardened,and both sheets exhibited a narrowed affected region with the increase of feed rate,while the rivet hardness shows no obvious change.Three fracture modes appeared accompanying the variations in lap-shear strength and energy absorption as the feed rate increased from 2 mm/s to 8 mm/s.Finally,the F-SPR process using a flat die was compared to those using a pip die and a flat bottom die to show the advantage of flat die on coping with the misalignment problem.
基金support of the National Natural Science Foundation of China(Grant Nos.52025058 and U1764251)the State Key Laboratory of Mechan-ical System and Vibration(Grant No.MSVZD202111)+1 种基金the Japan Society for the Promotion of Science(JSPS)KAKENHI(Grant No.21K14439)Shanghai Jiao Tong University.
文摘A recently developed friction self-piercing riveting(F-SPR)technique based on the combination of fric-tion stir processing and riveting has been reported to possess both solid-state bonding and mechanical fastening characteristics.However,there is still a lack of quantitative understanding of the hybrid en-hancement mechanism,hindering its engineering application.To fill in this gap,the current research investigated the microstructure evolution,microhardness distribution,and miniature-tensile performance of the aluminum alloy AA7075-T6 F-SPR joints by experiments.An accurate numerical simulation model was established to quantitatively evaluate the individual contributions of microstructure,local bonding strength,and macro interlocking to the performance of the joint,which could well explain the experi-mental results.It was found that due to the friction stirring of the rivet,solid-state bonding driven by dynamic recrystallization is realized between the trapped aluminum in the rivet cavity and the bottom aluminum sheet.The solid-state bonding zone has 75%yield strength,81%ultimate tensile strength,and 106%elongation compared to the base material.This solid-state bonding enables the internal interlock-ing between the trapped aluminum and the rivet to withstand the additional load,which forms a novel dual-interlock fastening mechanism and increases the peak cross-tension force by 14.3%compared to the single-interlock joint.
基金financially sponsored by the US Department Energy Vehicle Technologies Office, as part of the Joining Core Program。
文摘Carbon fiber reinforced polymer(CFRP) and AZ31B Mg alloy were joined by the friction self-piercing riveting(F-SPR) with different steel rivet shank sizes. With the increase of rivet shank size, lap shear fracture load and mechanical interlock distance increased. Ultrafine grains were formed at the joint in AZ31B as a result of dynamic recrystallization, which contributed to the higher hardness. Fatigue life of the CFRP-AZ31B joint was studied at various peak loads of 0.5, 1, 2, and 3 kN and compared with the resistance spot welded AZ31B-AZ31B from the open literature. The fatigue performance was better at higher peak load(>2 kN) and comparable to that of resistance spot welding of AZ31B to AZ31B at lower peak loads(<1 kN). From fractography, the crack initiation for lower peak load(<1 kN) case was observed at the fretting positions on the top and bottom surfaces of AZ31B sheet. When peak load was increased, fretting between the rivet and the top of AZ31B became more dominant to initiate a crack during fatigue testing.
基金This study was supported by the Research Program funded by the SeoulTech(Seoul National University of Science&Technology).
文摘The application of magnesium alloys to automobiles is increasing due to their superior specific strength and specific stiffness.In this study,an upper sheet of AZ31 magnesium alloy and a lower sheet of cold-rolled steel were joined by self-piercing riveting(SPR),a method commonly used to join automotive panels.A cross-shaped specimen was fabricated with a punching force of 35 kN,which exhibited the best joint strength for the SPR joint specimen geometry.Monotonic and fatigue strengths were evaluated using cross-shaped specimens at loading angles of 0°,45°,and 90°.The load amplitude corresponding to the fatigue endurance limit was assumed to be at 106 cycles,and the fatigue ratios(=fatigue endurance limit/static strength)at the loading angles of 0°,45°,and 90°are 22%,13%,and 9%,respectively.For all three loading angle specimens,fatigue cracks initiated at the triple point where the rivet shank,the upper sheet and the lower sheet are in contact with each other,with the cracks propagating through the thickness of the upper sheet and ultimately leading to fracture.The fatigue lifetimes were evaluated through the von-Mises stress,maximum principal stress,and equivalent stress intensity factor.It was found that the fatigue lifetimes could be evaluated most appropriately through the maximum principal stress.
基金financial support of the National Natural Science Foundation of China(Grant Nos.52025058 and U1764251)the National Key Research and Development Program of China(Grant No.2016YFB0101606-08)+1 种基金Shanghai Jiao Tong Universityfinancially supported by Project to Create Research and Educational Hubs for Innovative Manufacturing in Asia,Joining and Welding Research Institute,Osaka University。
文摘Friction self-piercing riveting(F-SPR)is an emerging technique for low ductility materials joining,which creates a mechanical and solid-state hybrid joint with a semi-hollow rivet.The severe plastic deformation of work materials and localized elevated temperatures during the F-SPR process yield complex and heterogeneous microstructures.The cut-off action of the work materials by the rivet further complicates the material flow during joint formation.This study employed the F-SPR process to join AA7075-T6 aluminum alloy sheets and systematically investigated the microstructural evolutions using electron backscatter diffraction(EBSD)techniques.The results suggested that as the base material approached the rivet,grains were deformed and recrystallized,forming two distinct fine grain zones(FGZs)surrounding the rivet and in the rivet cavity,re s pectively.Solid-state bonding of aluminum sheets occurred in the FGZs.The formation of FGZ outside the rivet is due to dynamic recrystallization(DRX)triggered by the sliding-to-sticking transition at the rivet/sheet interface.The FGZ in the rivet cavity was caused by the rotation of the trapped aluminum,which created a sticking affected zone at the trapped aluminum/lower sheet interface and led to DRX.Strain rate gradient in the trapped aluminum drove the further expansion of the sticking affected zone and resulted in grain refinement in a larger span.
