The uniaxial compressive strength(UCS)of rocks is a vital geomechanical parameter widely used for rock mass classification,stability analysis,and engineering design in rock engineering.Various UCS testing methods and ...The uniaxial compressive strength(UCS)of rocks is a vital geomechanical parameter widely used for rock mass classification,stability analysis,and engineering design in rock engineering.Various UCS testing methods and apparatuses have been proposed over the past few decades.The objective of the present study is to summarize the status and development in theories,test apparatuses,data processing of the existing testing methods for UCS measurement.It starts with elaborating the theories of these test methods.Then the test apparatus and development trends for UCS measurement are summarized,followed by a discussion on rock specimens for test apparatus,and data processing methods.Next,the method selection for UCS measurement is recommended.It reveals that the rock failure mechanism in the UCS testing methods can be divided into compression-shear,compression-tension,composite failure mode,and no obvious failure mode.The trends of these apparatuses are towards automation,digitization,precision,and multi-modal test.Two size correction methods are commonly used.One is to develop empirical correlation between the measured indices and the specimen size.The other is to use a standard specimen to calculate the size correction factor.Three to five input parameters are commonly utilized in soft computation models to predict the UCS of rocks.The selection of the test methods for the UCS measurement can be carried out according to the testing scenario and the specimen size.The engineers can gain a comprehensive understanding of the UCS testing methods and its potential developments in various rock engineering endeavors.展开更多
This paper introduces a kind of substitute bench testing method for vehicle application development and testing method of the test requirements,including battery fast conversion cycle test equipment,enter type incubat...This paper introduces a kind of substitute bench testing method for vehicle application development and testing method of the test requirements,including battery fast conversion cycle test equipment,enter type incubator,liquid-cooled machine and ancillary equipment composed of a set of test system,through the walk-in constant temperature box to simulate the new energy vehicles under different environmental conditions of the test requirements,Liquid-cooled machine and auxiliary parts to complete the battery thermal management system need cooling fluid conditions,the battery conversion cycle test equipment to simulate the dc fast charging way of filling pile,complete battery thermal management system test,shorten the filling fast charging time and improve battery fast charge security,for troubleshooting and data collection and analysis,Improve work efficiency,save costs,and eliminate customer anxiety about battery life and charging time.展开更多
During fully mechanized caving mining of thick coal seams,a large amount of strain energy accumulates in the roof,especially when the roof is thick and hard,making it difficultfor the roof to collapse naturally.When t...During fully mechanized caving mining of thick coal seams,a large amount of strain energy accumulates in the roof,especially when the roof is thick and hard,making it difficultfor the roof to collapse naturally.When the roof eventually collapses,the accumulated energy is released instantaneously,exerting a strong impact on the roadway.To address this issue,we proposed the synergistic control method of directional comprehensive pressure relief and energy-absorbing support(PREA)for roadways with hard roofs.In this study,we developed a three-dimensional physical model test apparatus for roof cutting and pressure relief.The 122108 ventilation roadway at the Caojiatan Coal Mine,which has a thick and hard roof,was taken as the engineering example.We analyzed the evolution patterns of stress and displacement in both the stope and the roadway surrounding rocks under different schemes.The PREA reinforcement mechanism for the roadway was investigated through comparative model tests between the new and original methods.The results showed that,compared to the original method,the new method reduced surrounding rock stress by up to 60.4%,and the roadway convergence decreased by up to 52.1%.Based on these results,we proposed corresponding engineering recommendations,which can guide fieldreinforcement design and application.The results demonstrate that the PREA method effectively reduces stress and ensures the safety and stability of the roadway.展开更多
The rock mass consists of rock blocks and structural planes,which can reduce its integrity and strength.Therefore,accurately obtaining the characteristics of the rock mass structural plane is a prerequisite for evalua...The rock mass consists of rock blocks and structural planes,which can reduce its integrity and strength.Therefore,accurately obtaining the characteristics of the rock mass structural plane is a prerequisite for evaluating stability and designing supports in underground engineering.Currently,there are no effective testing methods for the characteristic parameters of the rock mass structural plane in underground engineering.The paper presents the digital drilling technology as a new testing method of rock mass structural planes.Flawed rock specimens with cracks of varying widths and angles were used to simulate the rock mass structural planes,and the multifunctional rock mass digital drilling test system was employed to carry out the digital drilling tests.The analysis focuses on the variation laws of drilling parameters,such as drilling pressure and drilling torque,affected by the characteristics of prefabricated cracks,and clarifies the degradation mechanism of rock equivalent compressive strength.Additionally,an identification model for the characteristic parameters of rock mass structural planes during drilling is established.The test results indicate that the average difference of the characteristics of prefabricated cracks identified by the equivalent compressive strength is 2.45°and 0.82 mm,respectively.The identification model while drilling is verified to be correct due to the high identification accuracy.Based on this,a method for testing the characteristic parameters of the surrounding rock structural plane while drilling is proposed.The research offers a theoretical and methodological foundation for precise in situ identification of structural planes of the surrounding rock in underground engineering.展开更多
With the increase of underground engineering construction depth,the phenomenon of surrounding rock sudden failure caused by supporting structure failure occurs frequently.The conventional unloading con-fining pressure...With the increase of underground engineering construction depth,the phenomenon of surrounding rock sudden failure caused by supporting structure failure occurs frequently.The conventional unloading con-fining pressure(CUCP)test cannot simulate the plastic yielding and instantaneous unloading process of supporting structure to rock.Thus,a high stress loading-instantaneous unloading confining pressure(HSL-IUCP)test method was proposed and applied by considering bolt’s fracture under stress.The wall thickness of confining pressure plates and the material of bolts were changed to realize different confin-ing pressure loading stiffness(CPLS)and lateral maximum allowable deformation(LMAD).The superio-rity of HSL-ICPU method is verified compared with CUCP.The rock failure mechanism caused by sudden failure of supporting structure is obtained.The results show that when CPLS increases from 1.35 to 2.33 GN/m,rock’s peak strength and elastic modulus increase by 25.18%and 23.70%,respectively.The fracture characteristics change from tensile failure to tensile-shear mixed failure.When LMAD decreases from 0.40 to 0.16 mm,rock’s residual strength,peak strain,and residual strain decrease by 91.80%,16.94%,and 21.92%,respectively,and post-peak drop modulus increases by 140.47%.The test results obtained by this method are closer to rock’s real mechanical response characteristics compared with CUCP.展开更多
The efficiency of the aircraft Ice Protection Systems(IPSs)needs to be verified through icing wind tunnel tests.However,the scaling method for testing the IPSs has not been systematically established yet,and further r...The efficiency of the aircraft Ice Protection Systems(IPSs)needs to be verified through icing wind tunnel tests.However,the scaling method for testing the IPSs has not been systematically established yet,and further research is needed.In the present study,a scaling method specifically designed for thermal IPSs was derived from the governing equation of thin water film.Five scaling parameters were adopted to address the heat and mass transfer involved in the thermal anti-icing process.For method validation,icing wind tunnel tests were conducted using a jet engine nacelle model equipped with a bleed air IPS.The non-dimensional surface temperature and runback ice closely matched for both the reference and scaled conditions.The validation confirms that the scaling method is capable of achieving the similarity of surface temperature and the runback ice coverage.The anti-icing scaling method can serve as an important supplement to the existing icing similarity theory.展开更多
For real-time dynamic substructure testing(RTDST),the influence of the inertia force of fluid specimens on the stability and accuracy of the integration algorithms has never been investigated.Therefore,this study prop...For real-time dynamic substructure testing(RTDST),the influence of the inertia force of fluid specimens on the stability and accuracy of the integration algorithms has never been investigated.Therefore,this study proposes to investigate the stability and accuracy of the central difference method(CDM)for RTDST considering the specimen mass participation coefficient.First,the theory of the CDM for RTDST is presented.Next,the stability and accuracy of the CDM for RTDST considering the specimen mass participation coefficient are investigated.Finally,numerical simulations and experimental tests are conducted for verifying the effectiveness of the method.The study indicates that the stability of the algorithm is affected by the mass participation coefficient of the specimen,and the stability limit first increases and then decreases as the mass participation coefficient increases.In most cases,the mass participation coefficient will increase the stability limit of the algorithm,but in specific circumstances,the algorithm may lose its stability.The stability and accuracy of the CDM considering the mass participation coefficient are verified by numerical simulations and experimental tests on a three-story frame structure with a tuned liquid damper.展开更多
Previous studies on the hollow cylinder torsional shear test(HCTST)have mainly focused on the macroscopic behavior,while the micromechanical responses in soil specimens with shaped particles have rarely been investiga...Previous studies on the hollow cylinder torsional shear test(HCTST)have mainly focused on the macroscopic behavior,while the micromechanical responses in soil specimens with shaped particles have rarely been investigated.This paper develops a numerical model of the HCTST using the discrete element method(DEM).The method of bonded spheres in a hexagonal arrangement is proposed to generate flexible boundaries that can achieve real-time adjustment of the internal and external cell pressures and capture the inhomogeneous deformation in the radial direction during shearing.Representative angular particles are selected from Toyoura sand and reproduced in this model to approximate real sand particles.The model is then validated by comparing numerical and experimental results of HCTSTs on Toyoura sand with different major principal stress directions.Next,a series of HCTSTs with different combinations of major principal stress direction(a)and intermediate principal stress ratio(b)is simulated to quantitatively characterize the sand behavior under different shear conditions.The results show that the shaped particles are horizontally distributed before shearing,and the initial anisotropic packing structure further results in different stressestrain curves in cases with different a and b values.The distribution of force chains is affected by both a and b during the shear process,together with the formation of the shear bands in different patterns.The contact normal anisotropy and contact force anisotropy show different evolution patterns when either a or b varies,resulting in the differences in the non-coaxiality and other macroscopic responses.This study improves the understanding of the macroscopic response of sand from a microscopic perspective and provides valuable insights for the constitutive modeling of sand.展开更多
Considering the challenges posed by external disturbances on carrier-based aircraft land-ing control,higher demands are required for the precision and convergence of the carrier landingcontrol system.First,this paper ...Considering the challenges posed by external disturbances on carrier-based aircraft land-ing control,higher demands are required for the precision and convergence of the carrier landingcontrol system.First,this paper proposes an Adaptive Terminal Sliding Combined Super TwistingControl(ATS-STC)method to address the issues of low precision,slow convergence,and poor dis-turbance rejection capability resulting from external disturbances,such as carrier air-wake and deckmotion.By introducing a nonlinear term into the sliding surface and employing an integralapproach,the proposed ATS-STC method can ensure finite-time convergence and mitigate the chat-tering problem.An adaptive law is also utilized to estimate the external disturbances,therebyenhancing the anti-disturbance performance.Then,the stability and convergence time analysis ofthe designed controller are conducted.Based on the proposed method,an Automatic Carrier Land-ing System(ACLS)is developed to perform the carrier landing control task.Furthermore,a multi-dimensional validation is carried out.For the numerical simulation test,the Terminal Sliding ModeControl(TSMC)method and Proportion Integration Differentiation(PID)method are introducedas comparison,the quantitative assessment results show that the tracking error of TSMC and PIDcan reach 1.5 times and 2 times that of the proposed method.Finally,the Hardware-in-the-Loop(HIL)test and real flight test are conducted.All the experimental results demonstrate that the pro-posed control method is more effective and precise.展开更多
Starting with the goal and significance of software security testing,this paper introduces the main methods of software security testing in the open network environment,including formal security testing,white box test...Starting with the goal and significance of software security testing,this paper introduces the main methods of software security testing in the open network environment,including formal security testing,white box testing,fuzzy testing,model testing,and fault injection testing.A software security testing method based on a security target model is proposed.This paper provides new ideas for software security testing,better adapts to the open network environment,improves the efficiency and quality of testing,and builds a good software application environment.展开更多
The growing importance of maintaining and extending the functional lifespan of reinforced concrete structures has resulted in an increased emphasis on non-destructive testing techniques as essential tools for evaluati...The growing importance of maintaining and extending the functional lifespan of reinforced concrete structures has resulted in an increased emphasis on non-destructive testing techniques as essential tools for evaluating structural conditions.Non-destructive testing procedures offer a notable benefit in assessing the uniformity,homogeneity,ability to withstand compression,durability,and degree of corrosion in reinforcing bars within reinforced concrete structures.This study aimed to evaluate the existing condition of partially constructed residential buildings in Rewari district,located in the state of Haryana.The reinforced concrete structure of the building had been completed eight years ago,however,the project was abruptly stopped.Prior to recommencing the construction,it is important to assess the present state of the structure in order to evaluate the deterioration in Reinforced Cement Concrete(RCC).The building’s state was evaluated by visually inspecting the building,conducting on-site examinations,and analyzing samples in a laboratory.The findings emphasize the assessment of the robustness and durability of concrete to ascertain the degree of deterioration and degradation in the structure.The study incorporates visual inspection,and non-destructive evaluation utilizing different instruments to evaluate the corrosion condition of reinforcing bars.In addition,selected RCC columns,beams,and slabs undergo chemical testing.It has been observed that the strength results and chemical results were within permissible limits.展开更多
In heavy-duty long-distance transmission scenarios,steel wire ropes are widely used due to their unique advantages,and their safety is very important,which has also led to the rapid development of non-destructive test...In heavy-duty long-distance transmission scenarios,steel wire ropes are widely used due to their unique advantages,and their safety is very important,which has also led to the rapid development of non-destructive testing technology for steel wire ropes.The non-destructive testing technology for steel wire ropes is influenced by various factors such as its own structure and external working environment,and the testing process is relatively complex.Multiple testing methods and related types of sensors have also emerged.The electromagnetic detection method is currently the most effective method,but it also has its limitations in development and has not yet fully achieved the expected detection goals.In order to completely replace manual inspection work with the development of non-destructive testing technology for steel wire ropes,more in-depth research and long-term accumulation are still needed.展开更多
Astronomical site selection work is very hard.Unmanned technologies are important trends and solutions.We present a relatively easy method to plan a high reliability site selection which can extend the time from site ...Astronomical site selection work is very hard.Unmanned technologies are important trends and solutions.We present a relatively easy method to plan a high reliability site selection which can extend the time from site deployment to returning for maintaining by unmanned confirming the site.First,we redefine the reliability of a site selection deployment with the parameter of the trusty time,which means when we must return,and which can be relatively easy for estimating.The redefinition makes the reliability parameter as a Bayesian probability,and can be obtained by estimating besides testing,which makes the evaluation of each device's reliability much easier.Then we use block diagram tools in the Matlab Simulink software to construct structure diagram,and to link each component with relations of parallel,serial,protection,and so on.This makes the whole reliability value can be calculated at the time when we design or plan a site selection.We applied this concept and method in an actual site selection in Lenghu,Qinghai Province,China.The survey practice reveals its effectiveness and simpleness.展开更多
A dimensionless load-displacement model based on the energy-density equivalence principle is proposed to obtain the stress-strain relationships of metallic materials under monotonic indentations with various diameters...A dimensionless load-displacement model based on the energy-density equivalence principle is proposed to obtain the stress-strain relationships of metallic materials under monotonic indentations with various diameters of spherical indenters.Finite element simulations are carried out to verify the constitutive relations from the new model,involving indentations made with various spherical indenters.For each indenter,some quasi-static spherical indentation tests are conducted on the materials with 40 preset constitutive relationships.The results indicate that the stress-strain curves predicted by the model align with the preset curves under 200 loading conditions.Moreover,the goodness-of-fit between the predicted stress-strain curves and the preset curves exceeds0.96 for all indenters and materials.In the end,the indentation tests are conducted by the spherical indenters with the diameters of 1.587 mm for fifteen metallic materials and1 mm for eight metallic materials.The results show that the stress-strain curves obtained by the spherical indentation based on the new model closely match those obtained from the uniaxial tensile tests.The relative errors for both the proof strength at 0.2%plastic extension and the tensile strength are below 5%.展开更多
BACKGROUND Helicobacter pylori(H.pylori),a globally prevalent pathogen,is exhibiting increasing rates of antimicrobial resistance.However,clinical implementation of pre-treatment susceptibility testing remains limited...BACKGROUND Helicobacter pylori(H.pylori),a globally prevalent pathogen,is exhibiting increasing rates of antimicrobial resistance.However,clinical implementation of pre-treatment susceptibility testing remains limited due to the organism’s fastidious growth requirements and prolonged culture time.AIM To propose a novel detection method utilizing antibiotic-supplemented media to inhibit susceptible strains,while resistant isolates were identified through urease-mediated hydrolysis of urea,inducing a phenol red color change for visual confirmation.METHODS Colombia agar was supplemented with urea,phenol red,and nickel chloride,and the final pH was adjusted to 7.35.Antibiotic-selective media were prepared by incorporating amoxicillin(0.5μg/mL),clarithromycin(2μg/mL),metronidazole(8μg/mL),or levofloxacin(2μg/mL)into separate batches.Gastric antral biopsies were homogenized and inoculated at 1.0×105 CFU onto the media,and then incubated under microaerobic conditions at 37°C for 28-36 hours.Resistance was determined based on a color change from yellow to pink,and the results were validated via broth microdilution according to Clinical and Laboratory Standards Institute guidelines.RESULTS After 28-36 hours of incubation,the drug-resistant H.pylori isolates induced a light red color change in the medium.Conversely,susceptible strains(H.pylori 26695 and G27)produced no visible color change.Compared with the conventional 11-day protocol,the novel method significantly reduced detection time.Among 201 clinical isolates,182 were successfully evaluated using the new method,resulting in a 90.5%detection rate.This was consistent with the 95.5%agreement rate observed when compared with microdilution-based susceptibility testing.The success rate of the novel approach was significantly higher than that of the comparative method(P<0.01).The accuracy of the new method was comparable to that of the dilution method.CONCLUSION The novel detection method can rapidly detect H.pylori drug resistance within 28-36 hours.With its operational simplicity and high diagnostic performance,it holds strong potential for clinical application in the management of H.pylori antimicrobial resistance.展开更多
Plastometric experiments,supplemented with numerical simulations using the finite element method(FEM),can be advantageously used to characterize the deformation behavior of metallic materials.The accuracy of such simu...Plastometric experiments,supplemented with numerical simulations using the finite element method(FEM),can be advantageously used to characterize the deformation behavior of metallic materials.The accuracy of such simulations predicting deformation behaviors of materials is,however,primarily affected by the applied rheology law.The presented study focuses on the characterization of the deformation behavior of AISI 1045 type carbon steel,widely used e.g.,in automotive and power engineering,under extreme conditions(i.e.,high temperatures,strain rates).The study consists of two main parts:experimentally analyzing the flow stress development of the steel under different thermomechanical conditions via uniaxial hot compression tests and establishing the rheology law via numerical simulations implementing the experimentally acquired flow stress curves.The numerical simulations then not only serve to establish the rheology law but also to verify the reliability of the selected experimental process.The results of the numerical simulations showed that the established rheology law characterizes the behavior of the investigated steel with sufficient accuracy also at high temperatures and/or strain rates,and can,therefore,be used for practical purposes.Last but not least,supplementary microstructure analyses performed for the samples subjected to the highest deformation temperature provided a deeper insight into the effects of the applied(extreme)thermomechanical conditions on the behavior of the investigated steel.展开更多
This study presents an in-depth investigation into the shear strength characteristics of unsaturated soils,focusing on the influenceof shear rate and initial water saturation(S_(r0)).Utilizing the drained-vented(DV)tr...This study presents an in-depth investigation into the shear strength characteristics of unsaturated soils,focusing on the influenceof shear rate and initial water saturation(S_(r0)).Utilizing the drained-vented(DV)triaxial test method,the present study investigated the shear strength behavior of silty clay under various shear rates and water saturation levels,and compared the outcomes with traditional suction-controlled(SC)and constant water content(CW)tests.The findingshighlight the pivotal role of excess pore water pressure dissipation during shearing,which significantlyaffects the shear strength of both saturated and unsaturated soils.Notably,for soils with high initial water saturation,a decrease in shear strength is observed with an increase in shear rate,which is attributed to the rise in pore water pressure.Conversely,for soils with low initial water saturation,the shear rate exhibits minimal impact on shear strength due to negligible water drainage.The research delineates the optimal shear rates for DV tests based on the initial water saturation:a slower rate of 0.0028 mm/min for samples with high water saturation(S_(r0)>66%)and a faster rate of 0.8 mm/min for samples with low water saturation(S_(r0)≤66%).A novel testing methodology for determining unsaturated soil shear strength under DV conditions is introduced,streamlining the measurement process and significantly reducing testing time.This method not only promises substantial cost savings but also aligns closely with natural engineering conditions,offering valuable guidance for geotechnical applications.展开更多
In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method （DEM）. A digital specimen g...In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method （DEM）. A digital specimen generation procedure considering aggregate gradation and irregular shape is developed based on the probability theory and the Monte Carlo method. The virtual rutting test is then conducted based on the generated digital specimen. In addition, on the basis of the time-temperature superposition （TTS） principle, a calculation method is used to reduce the computation time of the virtual rutting test. The simulation results are compared with the laboratory measurements. The results show that the calculation method based on the TFS principle in the discrete element （DE） viscoelastic model can significantly reduce the computation time. The deformation law of asphalt mixtures in the virtual rutting test is similar to the laboratory measurements, and the deformation and the dynamic stability of the virtual rutting test are slightly greater than the laboratory measurements. The two-dimensional virtual rutting test can predict the permanent deformation performance of asphalt mixtures.展开更多
Testing methods of instrumental system in the marine magnetic survey have been studied in this paper, and the feasibility of each method has been testified by the observed data. The conclusion shows that the method br...Testing methods of instrumental system in the marine magnetic survey have been studied in this paper, and the feasibility of each method has been testified by the observed data. The conclusion shows that the method brought out can effectively eliminate the systematic error caused by the instrumental system, and greatly improve the surveying precision and the reliability of the survey results.展开更多
基金the National Natural Science Foundation of China(Grant Nos.52308403 and 52079068)the Yunlong Lake Laboratory of Deep Underground Science and Engineering(No.104023005)the China Postdoctoral Science Foundation(Grant No.2023M731998)for funding provided to this work.
文摘The uniaxial compressive strength(UCS)of rocks is a vital geomechanical parameter widely used for rock mass classification,stability analysis,and engineering design in rock engineering.Various UCS testing methods and apparatuses have been proposed over the past few decades.The objective of the present study is to summarize the status and development in theories,test apparatuses,data processing of the existing testing methods for UCS measurement.It starts with elaborating the theories of these test methods.Then the test apparatus and development trends for UCS measurement are summarized,followed by a discussion on rock specimens for test apparatus,and data processing methods.Next,the method selection for UCS measurement is recommended.It reveals that the rock failure mechanism in the UCS testing methods can be divided into compression-shear,compression-tension,composite failure mode,and no obvious failure mode.The trends of these apparatuses are towards automation,digitization,precision,and multi-modal test.Two size correction methods are commonly used.One is to develop empirical correlation between the measured indices and the specimen size.The other is to use a standard specimen to calculate the size correction factor.Three to five input parameters are commonly utilized in soft computation models to predict the UCS of rocks.The selection of the test methods for the UCS measurement can be carried out according to the testing scenario and the specimen size.The engineers can gain a comprehensive understanding of the UCS testing methods and its potential developments in various rock engineering endeavors.
文摘This paper introduces a kind of substitute bench testing method for vehicle application development and testing method of the test requirements,including battery fast conversion cycle test equipment,enter type incubator,liquid-cooled machine and ancillary equipment composed of a set of test system,through the walk-in constant temperature box to simulate the new energy vehicles under different environmental conditions of the test requirements,Liquid-cooled machine and auxiliary parts to complete the battery thermal management system need cooling fluid conditions,the battery conversion cycle test equipment to simulate the dc fast charging way of filling pile,complete battery thermal management system test,shorten the filling fast charging time and improve battery fast charge security,for troubleshooting and data collection and analysis,Improve work efficiency,save costs,and eliminate customer anxiety about battery life and charging time.
基金supported by the National Natural Science Foundation of China(Grant Nos.U24A2088 and 42277174)the Fundamental Research Funds for the Central Universities,China(Grant No.2024JCCXSB01).
文摘During fully mechanized caving mining of thick coal seams,a large amount of strain energy accumulates in the roof,especially when the roof is thick and hard,making it difficultfor the roof to collapse naturally.When the roof eventually collapses,the accumulated energy is released instantaneously,exerting a strong impact on the roadway.To address this issue,we proposed the synergistic control method of directional comprehensive pressure relief and energy-absorbing support(PREA)for roadways with hard roofs.In this study,we developed a three-dimensional physical model test apparatus for roof cutting and pressure relief.The 122108 ventilation roadway at the Caojiatan Coal Mine,which has a thick and hard roof,was taken as the engineering example.We analyzed the evolution patterns of stress and displacement in both the stope and the roadway surrounding rocks under different schemes.The PREA reinforcement mechanism for the roadway was investigated through comparative model tests between the new and original methods.The results showed that,compared to the original method,the new method reduced surrounding rock stress by up to 60.4%,and the roadway convergence decreased by up to 52.1%.Based on these results,we proposed corresponding engineering recommendations,which can guide fieldreinforcement design and application.The results demonstrate that the PREA method effectively reduces stress and ensures the safety and stability of the roadway.
基金supported by the National Key Research and Development Program of China(Grant No.2023YFC2907600)the National Natural Science Foundation of China(Grant Nos.42277174 and 52204260).
文摘The rock mass consists of rock blocks and structural planes,which can reduce its integrity and strength.Therefore,accurately obtaining the characteristics of the rock mass structural plane is a prerequisite for evaluating stability and designing supports in underground engineering.Currently,there are no effective testing methods for the characteristic parameters of the rock mass structural plane in underground engineering.The paper presents the digital drilling technology as a new testing method of rock mass structural planes.Flawed rock specimens with cracks of varying widths and angles were used to simulate the rock mass structural planes,and the multifunctional rock mass digital drilling test system was employed to carry out the digital drilling tests.The analysis focuses on the variation laws of drilling parameters,such as drilling pressure and drilling torque,affected by the characteristics of prefabricated cracks,and clarifies the degradation mechanism of rock equivalent compressive strength.Additionally,an identification model for the characteristic parameters of rock mass structural planes during drilling is established.The test results indicate that the average difference of the characteristics of prefabricated cracks identified by the equivalent compressive strength is 2.45°and 0.82 mm,respectively.The identification model while drilling is verified to be correct due to the high identification accuracy.Based on this,a method for testing the characteristic parameters of the surrounding rock structural plane while drilling is proposed.The research offers a theoretical and methodological foundation for precise in situ identification of structural planes of the surrounding rock in underground engineering.
基金the National Natural Science Foundation of China(Nos.52374218,52174122 and 52374094)Outstanding Youth Fund of Shandong Natural Science Foundation(No.ZR2022YQ49)Taishan Scholar Project in Shandong Province(Nos.tspd20210313 and tsqn202211150).
文摘With the increase of underground engineering construction depth,the phenomenon of surrounding rock sudden failure caused by supporting structure failure occurs frequently.The conventional unloading con-fining pressure(CUCP)test cannot simulate the plastic yielding and instantaneous unloading process of supporting structure to rock.Thus,a high stress loading-instantaneous unloading confining pressure(HSL-IUCP)test method was proposed and applied by considering bolt’s fracture under stress.The wall thickness of confining pressure plates and the material of bolts were changed to realize different confin-ing pressure loading stiffness(CPLS)and lateral maximum allowable deformation(LMAD).The superio-rity of HSL-ICPU method is verified compared with CUCP.The rock failure mechanism caused by sudden failure of supporting structure is obtained.The results show that when CPLS increases from 1.35 to 2.33 GN/m,rock’s peak strength and elastic modulus increase by 25.18%and 23.70%,respectively.The fracture characteristics change from tensile failure to tensile-shear mixed failure.When LMAD decreases from 0.40 to 0.16 mm,rock’s residual strength,peak strain,and residual strain decrease by 91.80%,16.94%,and 21.92%,respectively,and post-peak drop modulus increases by 140.47%.The test results obtained by this method are closer to rock’s real mechanical response characteristics compared with CUCP.
基金supported by the National Major Science and Technology Projects of China(J2019-Ⅲ-0010-0054).
文摘The efficiency of the aircraft Ice Protection Systems(IPSs)needs to be verified through icing wind tunnel tests.However,the scaling method for testing the IPSs has not been systematically established yet,and further research is needed.In the present study,a scaling method specifically designed for thermal IPSs was derived from the governing equation of thin water film.Five scaling parameters were adopted to address the heat and mass transfer involved in the thermal anti-icing process.For method validation,icing wind tunnel tests were conducted using a jet engine nacelle model equipped with a bleed air IPS.The non-dimensional surface temperature and runback ice closely matched for both the reference and scaled conditions.The validation confirms that the scaling method is capable of achieving the similarity of surface temperature and the runback ice coverage.The anti-icing scaling method can serve as an important supplement to the existing icing similarity theory.
基金National Natural Science Foundation of China under Grant Nos.51978213 and 51778190the National Key Research and Development Program of China under Grant Nos.2017YFC0703605 and 2016YFC0701106。
文摘For real-time dynamic substructure testing(RTDST),the influence of the inertia force of fluid specimens on the stability and accuracy of the integration algorithms has never been investigated.Therefore,this study proposes to investigate the stability and accuracy of the central difference method(CDM)for RTDST considering the specimen mass participation coefficient.First,the theory of the CDM for RTDST is presented.Next,the stability and accuracy of the CDM for RTDST considering the specimen mass participation coefficient are investigated.Finally,numerical simulations and experimental tests are conducted for verifying the effectiveness of the method.The study indicates that the stability of the algorithm is affected by the mass participation coefficient of the specimen,and the stability limit first increases and then decreases as the mass participation coefficient increases.In most cases,the mass participation coefficient will increase the stability limit of the algorithm,but in specific circumstances,the algorithm may lose its stability.The stability and accuracy of the CDM considering the mass participation coefficient are verified by numerical simulations and experimental tests on a three-story frame structure with a tuned liquid damper.
基金supports from the National Key R&D Program of China(Grant No.2023YFC3009400)Research Grants Council of Hong Kong(Grant Nos.15220221 and 15229223).
文摘Previous studies on the hollow cylinder torsional shear test(HCTST)have mainly focused on the macroscopic behavior,while the micromechanical responses in soil specimens with shaped particles have rarely been investigated.This paper develops a numerical model of the HCTST using the discrete element method(DEM).The method of bonded spheres in a hexagonal arrangement is proposed to generate flexible boundaries that can achieve real-time adjustment of the internal and external cell pressures and capture the inhomogeneous deformation in the radial direction during shearing.Representative angular particles are selected from Toyoura sand and reproduced in this model to approximate real sand particles.The model is then validated by comparing numerical and experimental results of HCTSTs on Toyoura sand with different major principal stress directions.Next,a series of HCTSTs with different combinations of major principal stress direction(a)and intermediate principal stress ratio(b)is simulated to quantitatively characterize the sand behavior under different shear conditions.The results show that the shaped particles are horizontally distributed before shearing,and the initial anisotropic packing structure further results in different stressestrain curves in cases with different a and b values.The distribution of force chains is affected by both a and b during the shear process,together with the formation of the shear bands in different patterns.The contact normal anisotropy and contact force anisotropy show different evolution patterns when either a or b varies,resulting in the differences in the non-coaxiality and other macroscopic responses.This study improves the understanding of the macroscopic response of sand from a microscopic perspective and provides valuable insights for the constitutive modeling of sand.
基金supported by the National Natural Science Foundation of China(No.T2288101)the National Key Research and Development Project,China(No.2020YFC1512500)the Academic Excellence Foundation of Beijing University of Aeronautics and Astronautics(BUAA)。
文摘Considering the challenges posed by external disturbances on carrier-based aircraft land-ing control,higher demands are required for the precision and convergence of the carrier landingcontrol system.First,this paper proposes an Adaptive Terminal Sliding Combined Super TwistingControl(ATS-STC)method to address the issues of low precision,slow convergence,and poor dis-turbance rejection capability resulting from external disturbances,such as carrier air-wake and deckmotion.By introducing a nonlinear term into the sliding surface and employing an integralapproach,the proposed ATS-STC method can ensure finite-time convergence and mitigate the chat-tering problem.An adaptive law is also utilized to estimate the external disturbances,therebyenhancing the anti-disturbance performance.Then,the stability and convergence time analysis ofthe designed controller are conducted.Based on the proposed method,an Automatic Carrier Land-ing System(ACLS)is developed to perform the carrier landing control task.Furthermore,a multi-dimensional validation is carried out.For the numerical simulation test,the Terminal Sliding ModeControl(TSMC)method and Proportion Integration Differentiation(PID)method are introducedas comparison,the quantitative assessment results show that the tracking error of TSMC and PIDcan reach 1.5 times and 2 times that of the proposed method.Finally,the Hardware-in-the-Loop(HIL)test and real flight test are conducted.All the experimental results demonstrate that the pro-posed control method is more effective and precise.
文摘Starting with the goal and significance of software security testing,this paper introduces the main methods of software security testing in the open network environment,including formal security testing,white box testing,fuzzy testing,model testing,and fault injection testing.A software security testing method based on a security target model is proposed.This paper provides new ideas for software security testing,better adapts to the open network environment,improves the efficiency and quality of testing,and builds a good software application environment.
文摘The growing importance of maintaining and extending the functional lifespan of reinforced concrete structures has resulted in an increased emphasis on non-destructive testing techniques as essential tools for evaluating structural conditions.Non-destructive testing procedures offer a notable benefit in assessing the uniformity,homogeneity,ability to withstand compression,durability,and degree of corrosion in reinforcing bars within reinforced concrete structures.This study aimed to evaluate the existing condition of partially constructed residential buildings in Rewari district,located in the state of Haryana.The reinforced concrete structure of the building had been completed eight years ago,however,the project was abruptly stopped.Prior to recommencing the construction,it is important to assess the present state of the structure in order to evaluate the deterioration in Reinforced Cement Concrete(RCC).The building’s state was evaluated by visually inspecting the building,conducting on-site examinations,and analyzing samples in a laboratory.The findings emphasize the assessment of the robustness and durability of concrete to ascertain the degree of deterioration and degradation in the structure.The study incorporates visual inspection,and non-destructive evaluation utilizing different instruments to evaluate the corrosion condition of reinforcing bars.In addition,selected RCC columns,beams,and slabs undergo chemical testing.It has been observed that the strength results and chemical results were within permissible limits.
文摘In heavy-duty long-distance transmission scenarios,steel wire ropes are widely used due to their unique advantages,and their safety is very important,which has also led to the rapid development of non-destructive testing technology for steel wire ropes.The non-destructive testing technology for steel wire ropes is influenced by various factors such as its own structure and external working environment,and the testing process is relatively complex.Multiple testing methods and related types of sensors have also emerged.The electromagnetic detection method is currently the most effective method,but it also has its limitations in development and has not yet fully achieved the expected detection goals.In order to completely replace manual inspection work with the development of non-destructive testing technology for steel wire ropes,more in-depth research and long-term accumulation are still needed.
基金supported by the Investigation of Technological Infrastructure Resources(No.2023FY101101)the National Natural Science Foundation of China(NSFC)(No.11073027 and No.12373104)。
文摘Astronomical site selection work is very hard.Unmanned technologies are important trends and solutions.We present a relatively easy method to plan a high reliability site selection which can extend the time from site deployment to returning for maintaining by unmanned confirming the site.First,we redefine the reliability of a site selection deployment with the parameter of the trusty time,which means when we must return,and which can be relatively easy for estimating.The redefinition makes the reliability parameter as a Bayesian probability,and can be obtained by estimating besides testing,which makes the evaluation of each device's reliability much easier.Then we use block diagram tools in the Matlab Simulink software to construct structure diagram,and to link each component with relations of parallel,serial,protection,and so on.This makes the whole reliability value can be calculated at the time when we design or plan a site selection.We applied this concept and method in an actual site selection in Lenghu,Qinghai Province,China.The survey practice reveals its effectiveness and simpleness.
基金Project supported by the National Natural Science Foundation of China(Nos.11872320 and 12072294)。
文摘A dimensionless load-displacement model based on the energy-density equivalence principle is proposed to obtain the stress-strain relationships of metallic materials under monotonic indentations with various diameters of spherical indenters.Finite element simulations are carried out to verify the constitutive relations from the new model,involving indentations made with various spherical indenters.For each indenter,some quasi-static spherical indentation tests are conducted on the materials with 40 preset constitutive relationships.The results indicate that the stress-strain curves predicted by the model align with the preset curves under 200 loading conditions.Moreover,the goodness-of-fit between the predicted stress-strain curves and the preset curves exceeds0.96 for all indenters and materials.In the end,the indentation tests are conducted by the spherical indenters with the diameters of 1.587 mm for fifteen metallic materials and1 mm for eight metallic materials.The results show that the stress-strain curves obtained by the spherical indentation based on the new model closely match those obtained from the uniaxial tensile tests.The relative errors for both the proof strength at 0.2%plastic extension and the tensile strength are below 5%.
基金Supported by the Guangxi Science and Technology Major Projects,No.AA23073012the National Natural Science Foundation of China,No.32360035 and No.32060018。
文摘BACKGROUND Helicobacter pylori(H.pylori),a globally prevalent pathogen,is exhibiting increasing rates of antimicrobial resistance.However,clinical implementation of pre-treatment susceptibility testing remains limited due to the organism’s fastidious growth requirements and prolonged culture time.AIM To propose a novel detection method utilizing antibiotic-supplemented media to inhibit susceptible strains,while resistant isolates were identified through urease-mediated hydrolysis of urea,inducing a phenol red color change for visual confirmation.METHODS Colombia agar was supplemented with urea,phenol red,and nickel chloride,and the final pH was adjusted to 7.35.Antibiotic-selective media were prepared by incorporating amoxicillin(0.5μg/mL),clarithromycin(2μg/mL),metronidazole(8μg/mL),or levofloxacin(2μg/mL)into separate batches.Gastric antral biopsies were homogenized and inoculated at 1.0×105 CFU onto the media,and then incubated under microaerobic conditions at 37°C for 28-36 hours.Resistance was determined based on a color change from yellow to pink,and the results were validated via broth microdilution according to Clinical and Laboratory Standards Institute guidelines.RESULTS After 28-36 hours of incubation,the drug-resistant H.pylori isolates induced a light red color change in the medium.Conversely,susceptible strains(H.pylori 26695 and G27)produced no visible color change.Compared with the conventional 11-day protocol,the novel method significantly reduced detection time.Among 201 clinical isolates,182 were successfully evaluated using the new method,resulting in a 90.5%detection rate.This was consistent with the 95.5%agreement rate observed when compared with microdilution-based susceptibility testing.The success rate of the novel approach was significantly higher than that of the comparative method(P<0.01).The accuracy of the new method was comparable to that of the dilution method.CONCLUSION The novel detection method can rapidly detect H.pylori drug resistance within 28-36 hours.With its operational simplicity and high diagnostic performance,it holds strong potential for clinical application in the management of H.pylori antimicrobial resistance.
文摘Plastometric experiments,supplemented with numerical simulations using the finite element method(FEM),can be advantageously used to characterize the deformation behavior of metallic materials.The accuracy of such simulations predicting deformation behaviors of materials is,however,primarily affected by the applied rheology law.The presented study focuses on the characterization of the deformation behavior of AISI 1045 type carbon steel,widely used e.g.,in automotive and power engineering,under extreme conditions(i.e.,high temperatures,strain rates).The study consists of two main parts:experimentally analyzing the flow stress development of the steel under different thermomechanical conditions via uniaxial hot compression tests and establishing the rheology law via numerical simulations implementing the experimentally acquired flow stress curves.The numerical simulations then not only serve to establish the rheology law but also to verify the reliability of the selected experimental process.The results of the numerical simulations showed that the established rheology law characterizes the behavior of the investigated steel with sufficient accuracy also at high temperatures and/or strain rates,and can,therefore,be used for practical purposes.Last but not least,supplementary microstructure analyses performed for the samples subjected to the highest deformation temperature provided a deeper insight into the effects of the applied(extreme)thermomechanical conditions on the behavior of the investigated steel.
基金The authors are grateful for the Beijing Natural Science Foundation(Grant No.8242017)。
文摘This study presents an in-depth investigation into the shear strength characteristics of unsaturated soils,focusing on the influenceof shear rate and initial water saturation(S_(r0)).Utilizing the drained-vented(DV)triaxial test method,the present study investigated the shear strength behavior of silty clay under various shear rates and water saturation levels,and compared the outcomes with traditional suction-controlled(SC)and constant water content(CW)tests.The findingshighlight the pivotal role of excess pore water pressure dissipation during shearing,which significantlyaffects the shear strength of both saturated and unsaturated soils.Notably,for soils with high initial water saturation,a decrease in shear strength is observed with an increase in shear rate,which is attributed to the rise in pore water pressure.Conversely,for soils with low initial water saturation,the shear rate exhibits minimal impact on shear strength due to negligible water drainage.The research delineates the optimal shear rates for DV tests based on the initial water saturation:a slower rate of 0.0028 mm/min for samples with high water saturation(S_(r0)>66%)and a faster rate of 0.8 mm/min for samples with low water saturation(S_(r0)≤66%).A novel testing methodology for determining unsaturated soil shear strength under DV conditions is introduced,streamlining the measurement process and significantly reducing testing time.This method not only promises substantial cost savings but also aligns closely with natural engineering conditions,offering valuable guidance for geotechnical applications.
基金The National Natural Science Foundation of China(No.51108081)
文摘In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method （DEM）. A digital specimen generation procedure considering aggregate gradation and irregular shape is developed based on the probability theory and the Monte Carlo method. The virtual rutting test is then conducted based on the generated digital specimen. In addition, on the basis of the time-temperature superposition （TTS） principle, a calculation method is used to reduce the computation time of the virtual rutting test. The simulation results are compared with the laboratory measurements. The results show that the calculation method based on the TFS principle in the discrete element （DE） viscoelastic model can significantly reduce the computation time. The deformation law of asphalt mixtures in the virtual rutting test is similar to the laboratory measurements, and the deformation and the dynamic stability of the virtual rutting test are slightly greater than the laboratory measurements. The two-dimensional virtual rutting test can predict the permanent deformation performance of asphalt mixtures.
文摘Testing methods of instrumental system in the marine magnetic survey have been studied in this paper, and the feasibility of each method has been testified by the observed data. The conclusion shows that the method brought out can effectively eliminate the systematic error caused by the instrumental system, and greatly improve the surveying precision and the reliability of the survey results.
