The effect of trace addition of 0.1wt%Y on the grain refinement and mechanical properties of Al-2.2Li-1.5Cu-0.5Mg-1Zn-0.2Zr-0.2Sc alloys at as-cast and heat-treated states was investigated.Results show that the additi...The effect of trace addition of 0.1wt%Y on the grain refinement and mechanical properties of Al-2.2Li-1.5Cu-0.5Mg-1Zn-0.2Zr-0.2Sc alloys at as-cast and heat-treated states was investigated.Results show that the addition of 0.1wt%Y into the Al-2.2Li-1.5Cu-0.5Mg-1Zn-0.2Zr-0.2Sc alloys can elevate the nucleation temperature of the Al_(3)(Sc,Zr)phase,leading to the preferential precipitation of the Al_(3)(Sc,Zr)phase and increasing the amount of Al_(3)(Sc,Zr)phase in the matrix.Al_(3)(Sc,Zr)phase can also act as a heterogeneous nucleation site in theα-Al matrix to promote nucleation and refine grains.The addition of element Y changes the precipitation phase characteristics at the grain boundaries in the as-cast alloy,which changes the distribution characteristics of secondary phases from initially continuous and coarse strip-like distribution at grain boundaries into the discontinuous dot-like and rod-like distribution.Besides,the size of secondary phases becomes smaller and their amount increases.Under the combined effects of grain refinement strengthening and precipitation strengthening,the Al-2.2Li-1.5Cu-0.5Mg-1Zn-0.2Zr-0.2Sc-0.1Y alloy after 175℃/10 h aging treatment achieves an ultimate tensile strength of 412 MPa and an elongation of 6.3%.Compared with those of the alloy without Y addition,the ultimate tensile strength and elongation of the added alloy increase by 16.1%and 53.7%,respectively.展开更多
In modern ZnO varistors,traditional aging mechanisms based on increased power consumption are no longer relevant due to reduced power consumption during DC aging.Prolonged exposure to both AC and DC voltages results i...In modern ZnO varistors,traditional aging mechanisms based on increased power consumption are no longer relevant due to reduced power consumption during DC aging.Prolonged exposure to both AC and DC voltages results in increased leakage current,decreased breakdown voltage,and lower nonlinearity,ultimately compromising their protective performance.To investigate the evolution in electrical properties during DC aging,this work developed a finite element model based on Voronoi networks and conducted accelerated aging tests on commercial varistors.Throughout the aging process,current-voltage characteristics and Schottky barrier parameters were measured and analyzed.The results indicate that when subjected to constant voltage,current flows through regions with larger grain sizes,forming discharge channels.As aging progresses,the current focus increases on these channels,leading to a decline in the varistor’s overall performance.Furthermore,analysis of the Schottky barrier parameters shows that the changes in electrical performance during aging are non-monotonic.These findings offer theoretical support for understanding the aging mechanisms and condition assessment of modern stable ZnO varistors.展开更多
In this review,the synthesis,functions,and applications of the polymers containing germanium and tin,which are heavy group 14 elements,in their polymer frameworks are summarized.Germanium and tin can form similar skel...In this review,the synthesis,functions,and applications of the polymers containing germanium and tin,which are heavy group 14 elements,in their polymer frameworks are summarized.Germanium and tin can form similar skeletal structures with their homologues carbon and silicon,whereas the polymers containing germanium and tin show unique properties derived from their large atomic radii and weak binding energies.For example,polygermane and polystannane exhibited light absorption in the UV–visible region and conductivity because of theσ-conjugation through the polymer main-chain constructed byσ-bonds between heavy elements.Theσ-conjugation was affected by the conformational change of the polymer main-chain,and thermochromic properties can be induced.Furthermore,the weak bonds were able to be cleaved homolytically upon photoirradiation,and radicals were subsequently generated.By incorporating hypervalent heavy elements into theπ-conjugated system,it was possible to modulate the electronic structures of theπ-conjugated system throughσ*–π*conjugation with highly coordinated elements.Finally,applications for organic solar cells,organic lightemitting materials,and chemical sensors have been achieved.Herein,representative synthetic methods and unique properties for creating smart materials with germanium and tin will be explained.展开更多
The Martian core mainly contains iron,nickel and some light elements.However,controversies remain about the structure and chemical composition of the Martian core due to a lack of samples and marsquake data.Recently,t...The Martian core mainly contains iron,nickel and some light elements.However,controversies remain about the structure and chemical composition of the Martian core due to a lack of samples and marsquake data.Recently,the InSight lander collected long-term marsquake data,which improved the Martian interior structure model.B ased on the preliminary analysis of marsquake data,Mars has a molten liquid core with a radius of around 1700 km.As the Martian core has a smaller density and lower temperature than pure iron at corresponding pressure and temperature conditions,some light elements are introduced to reduce the density and liquidus temperature.With various methods for seismic analysis,in-situ high-pressure and high-temperature experiments,and first-principal calculations,the Martian core composition and evolution models have been updated in the past few years.Here,we review those studies on the light elements in the Martian core from four aspects including(1)high-temperature and high-pressure experiments,(2)marsquake data,(3)mineral physics model with molecular dynamics simulations and(4)cosmochemistry investigation.We discussed the effect of different light elements on the Martian core s density,sound velocity and liquidus temperature.Moreover,the review examines the varieties,abundances and forms of light elements in the Martian core.展开更多
Maintaining optimal crop nutritional levels is crucial for maximizing yield and enhancing stress resistance.In addition to the 17 essential nutrients,there are many plant-beneficial elements:silicon,aluminum,selenium,...Maintaining optimal crop nutritional levels is crucial for maximizing yield and enhancing stress resistance.In addition to the 17 essential nutrients,there are many plant-beneficial elements:silicon,aluminum,selenium,titanium,iodine,vanadium,cobalt,sodium,and rare earth elements.They are not essential for all plants,but some are crucial for specific plant species.However,the mechanisms of action of many beneficial elements are still unclear,and products containing beneficial elements have not been widely accepted and used by the public.This review systematically summarizes the current knowledge of plant-beneficial elements.Most importantly,we offer suggestions for future research on beneficial elements,which include integrating cross-disciplinary and innovative technologies,expanding the scope of application and elemental spies,broadening the spatial and temporal scales of research,incorporating beneficial elements into the soil health evaluation system,and shifting from single to multi-element applications.In the future,research on beneficial elements should be closely centered around“mechanism+application”to meet the ever-increasing demands driven by population growth,improve human health,tackle environmental challenges,and promote rural economic development.展开更多
A novel method for the synthesis of 2,4-disubstituted thiophenes via the reactions of N,N-disubstituted enaminones and elemental sulfur is developed.By simply heating the substrates in pure water in the presence of Na...A novel method for the synthesis of 2,4-disubstituted thiophenes via the reactions of N,N-disubstituted enaminones and elemental sulfur is developed.By simply heating the substrates in pure water in the presence of NaOH,the thiophene annulation practically takes place via the generation of one C-C and two C-S bonds via cascade dual C-H functionalization and C-N bond thiolation without using any transition metal reagent.展开更多
The development of catalytic multicomponent reactions for constructing complex organic scaffolds from readily accessible commodity chemicals is a key pursuit in contemporary synthetic chemistry.Current methods for syn...The development of catalytic multicomponent reactions for constructing complex organic scaffolds from readily accessible commodity chemicals is a key pursuit in contemporary synthetic chemistry.Current methods for synthesizing thioesters primarily rely on the acylation of thiols,which produces substantial waste and requires malodorous,unstable sulfur sources.In this work,we introduce a photocatalyzed hydrogen transfer strategy that enables a three-component synthesis of thioesters using abundant primary alcohols,easily available alkenes and elemental sulfur under mild conditions.This protocol demonstrates broad applicability and high chemo-and regioselectivity for both primary alcohols and alkenes,highlighting the advantage and potential of photo-mediated hydrogen transfer in facilitating multicomponent reactions using primary alcohol and elemental sulfur feedstocks.展开更多
Organic-rich sediments represent vital components of Earth's geochemical cycles, acting both as potential hydrocarbon and coal reservoirs and as unconventional archives for critical metals such as rare earth eleme...Organic-rich sediments represent vital components of Earth's geochemical cycles, acting both as potential hydrocarbon and coal reservoirs and as unconventional archives for critical metals such as rare earth elements(REEs). With the growing emphasis on clean energy technologies, the Cenozoic organic deposits of India have gained renewed significance;however, those from the southern state of Kerala remain understudied. This study investigates lignite and associated carbonaceous sediments from the Cheruvathur and Warkalli Formations using a multi-proxy approach integrating organic petrography,infrared spectroscopy, stable carbon isotopes, and REE geochemistry. The lignite exhibits huminite dominance with Type Ⅲ kerogen, deposited in a wet, mesotropic bog forest swamp under anoxic conditions. The mineral assemblage, dominated by kaolinite, quartz, illite, montmorillonite, feldspar,and pyrite/marcasite, reflects strong chemical alteration in a reducing environment. The δ^(13)C values(-25.1 to-27.3) indicate a C_(3) angiosperm source and deposition in tropical to subtropical swamp settings. REE patterns reveal LREE enrichment in carbonaceous shales and HREE enrichment in lignite,with distinct Ce, Eu, and Gd anomalies associated with provenance and redox conditions. The findings provide new insights into the paleoenvironmental evolution of Kerala's Cenozoic basins and highlight their potential as unconventional REE-bearing resources in the context of the global energy transition.展开更多
Against the backdrop of profound restructuring in the global industrial and supply chains,data elements have emerged as a critical force driving the transformation of enterprises'new quality productive forces.To a...Against the backdrop of profound restructuring in the global industrial and supply chains,data elements have emerged as a critical force driving the transformation of enterprises'new quality productive forces.To address the ambiguity surrounding its micro-level empowerment mechanism,this paper empirically examines the impact of data elements on enterprises'new quality productive forces and its transmission channels using panel data of Chinese A-share listed firms from 2014 to 2023.The results show that data elements significantly improve the level of enterprises'new quality productive forces.Heterogeneity analysis indicates that this promotional effect is more pronounced in non-state-owned enterprises,large-scale enterprises,and low-leverage enterprises.Mechanism tests confirm that data elements empower new quality productive forces through three paths:enhancing enterprise innovation capability,improving internal operational efficiency,and promoting inter-firm collaboration efficiency.This study provides empirical evidence for understanding the micro-level empowerment logic of data elements and offers theoretical references and practical implications for advancing the deep integration of the digital economy and the real economy.展开更多
The influence of varying levels of impurity elements on the hot corrosion resistance of the DD98M alloy in Na_(2)SO_(4)+NaCl salt at 950℃ was investigated.The results indicate that the corrosion resistance of the DD9...The influence of varying levels of impurity elements on the hot corrosion resistance of the DD98M alloy in Na_(2)SO_(4)+NaCl salt at 950℃ was investigated.The results indicate that the corrosion resistance of the DD98M alloy significantly decreases with an increase in impurity content,and the presence of nitrogen leads to an increase in alloy porosity.These porosities promote the rapid diffusion of molten salt and oxygen into the alloy,resulting in a bilateral diffusion of oxygen and sulfur,which leads to an accumulation of these elements at the oxide−matrix interface.This process contributes to the formation and propagation of interfacial cracks.A growth model was developed for hot corrosion products in alloys with varying impurity elements.展开更多
The buoyancy-induced flow constitutes a core scientific issue for thermal management of electronic devices and thermal design of energy systems,where accurate characterization of flow and heat transfer is essential to...The buoyancy-induced flow constitutes a core scientific issue for thermal management of electronic devices and thermal design of energy systems,where accurate characterization of flow and heat transfer is essential to improve thermal efficiency.In this work,buoyancy-induced flow above two heating elements flush-mounted at the bottom of a square enclosure containing air is numerically investigated over a range of Rayleigh numbers(0<Ra≤1.5×10^(8)),with a focus on equal and unequal heat flux conditions under a constraint of constant total thermal energy input.Distinct flow transitions are observed in both cases,leading to the identification of three flow regimes:Steady,periodic unsteady,and chaotic unsteady.Two types of periodic flows are distinguished,in which the first is a periodic flow dominated by a fundamental frequency(FF)and its integer-multiple frequencies(INTMF),while the second is a more complex periodic flow featuring FF,INTMF,and their sub-harmonics.The transitions between these regimes are affected by the relative heat flux of the two heaters.When the heat flux of the two heaters is unequal,the range of Rayleigh numbers corresponding to periodic flow is suppressed.It is also found that the time-averaged maximum temperature of the strong heater increases more rapidly with Ra,while that of the weak heater increases more slowly,reflecting the interaction between buoyancy-driven flow dynamics and asymmetric heat input.Analysis of the time-averaged Nusselt number demonstrates that heat dissipation from the isothermal walls remains roughly equivalent,even when the heat flux of the two heaters differs by a factor of two.These findings highlight the critical roles of Rayleigh number,the number of heaters,and the heat flux ratio of the heaters in determining heat transfer and flow characteristics for buoyancy-driven convection systems,providing important theoretical support and design references for engineering scenarios such as electronic devices and design of new energy systems.展开更多
This study develops a surrogate super-resolution(SR)framework that accelerates finite element method(FEM)-based computational fluid dynamics(CFD)using deep learning.High-resolution(HR)FEM-based CFDremains computationa...This study develops a surrogate super-resolution(SR)framework that accelerates finite element method(FEM)-based computational fluid dynamics(CFD)using deep learning.High-resolution(HR)FEM-based CFDremains computationally prohibitive for time-sensitive applications,including patient-specific aneurysm hemodynamics where rapid turnaround is valuable.The proposed pipeline learns to reconstruct HR velocity-magnitude fields fromlow-resolution(LR)FEM solutions generated under the same governing equations and boundary conditions.It consistsof three modules:(i)offline pre-training of a residual network on representative vascular geometries;(ii)lightweightfine-tuning to adapt the pretrained model to geometric variability,including patient-specific aneurysm morphologies;and(iii)an unstructured-to-structured sampling strategy with region-of-interest upsampling that concentrates resolution in flow-critical zones(e.g.,the aneurysm sac)rather than the full domain.This targeted reconstruction substantiallyreduces inference and post-processing cost while preserving key HR flow features.Experiments on cerebral aneurysmmodels show that HR velocity-magnitude fields can be recovered with accuracy comparable to direct HR simulationsat less than 1%of the direct HR simulation cost per analysis(LR simulation and SR inference),while adaptation to newgeometries requires only lightweight fine-tuning with limited target-specific HR data.While clinical endpoints andadditional variables(e.g.,pressure or wall-based metrics)are left for future work,the results indicate that the proposedsurrogate SR approach can streamline FEM-based CFD workflows toward near real-time hemodynamic analysis acrossmorphologically similar vascular models.展开更多
A new quadrilateral edge element method is proposed and analyzed for Maxwell equations.This proposed method is based on Duan-Liang quadrilateral element(Math.Comp.73(2004),pp.1–18).When applied to the eigenvalue prob...A new quadrilateral edge element method is proposed and analyzed for Maxwell equations.This proposed method is based on Duan-Liang quadrilateral element(Math.Comp.73(2004),pp.1–18).When applied to the eigenvalue problem,the method is spectral-correct and spurious-free.Stability and error estimates are obtained,including the interpolation error estimates and the error estimates between the finite element solution and the exact solution.The method is suitable for singular solution as well as smooth solution,and consequently,the method is valid for nonconvex domains which may have a number of reentrant corners.Of course,the method is suitable for arbitrary quadrilaterals(under the usual shape-regular condition).展开更多
Effects of alloying elements Ni,Co,Mn,Cr,and H on the stacking fault energy(SFE)ofγ-Fe and its microscopic mechanisms were systematically investigated.Generalized SFE calculations show that individual alloying elemen...Effects of alloying elements Ni,Co,Mn,Cr,and H on the stacking fault energy(SFE)ofγ-Fe and its microscopic mechanisms were systematically investigated.Generalized SFE calculations show that individual alloying elements Ni,Co,and H increase SFE ofγ-Fe,whereas Mn and Cr decrease SFE.The influence of alloying elements on SFE exhibits short-range characteristics.The effect of synergistic interaction of alloying elements and H on SFE was further investigated.Results show that the co-alloying of Ni/Co with H exacerbates the effect of H on the increase in SFE.In contrast,the synergistic effect of Mn/Cr with H tends to inhibit H from the increasing SFE.Finally,the electronic structure analysis elucidated the microscopic mechanism of the change in SFE.Alloying elements modulate SFE by changing the interatomic charge density at the stacking fault plane and the density of states of the stacking fault structure at the Fermi level.The present results add to the knowledge of alloying related influence on the mechanical property and hydrogen embrittlement ofγ-Fe.展开更多
This study investigates the effect of Ce content on the hydrogen storage properties of Ti_(0.98)Zr_(0.02)Mn_(1.5)Cr_(0.05)V_(0.43)Fe_(0.09)Ce_(x)(x=0,0.02,0.04,and 0.06,at%)alloys.Microstructural analysis of these all...This study investigates the effect of Ce content on the hydrogen storage properties of Ti_(0.98)Zr_(0.02)Mn_(1.5)Cr_(0.05)V_(0.43)Fe_(0.09)Ce_(x)(x=0,0.02,0.04,and 0.06,at%)alloys.Microstructural analysis of these alloys revealed dendritic microstructures without the segregation of chemical elements,with the C14 Laves phase identified as the dominant phase.After two activation cycles at 4 MPa and 293 K,the alloys exhibited excellent hydrogen absorption properties.The addition of Ce significantly improved the kinetics of the alloys.At x=0.02,the hydrogen absorption capacity reached 90%of its maximum within 137 s at 293 K.Pressure-composition-temperature curves indicated that hydrogen absorption capacity initially increased first and then decreased with increasing Ce content,reaching a maximum value of 1.85wt%at x=0.04.Thermodynamic results demonstrated that the enthalpy and entropy of hydrogen absorption followed a similar trend,which was consistent with the variation in hydrogen storage capacity.Thus,the improvement in hydrogen absorption capacity due to the addition of Ce is attributed to the increase in enthalpy.The increase of the lattice constant in the C14 Laves phase and the deoxidization effect of Ce are expected to be beneficial for the improvement of hydrogen absorption kinetics.展开更多
The moving morphable component(MMC)topology optimization method,as a typical explicit topology optimization method,has been widely concerned.In the MMC topology optimization framework,the surrogate material model is m...The moving morphable component(MMC)topology optimization method,as a typical explicit topology optimization method,has been widely concerned.In the MMC topology optimization framework,the surrogate material model is mainly used for finite element analysis at present,and the effectiveness of the surrogate material model has been fully confirmed.However,there are some accuracy problems when dealing with boundary elements using the surrogate material model,which will affect the topology optimization results.In this study,a boundary element reconstruction(BER)model is proposed based on the surrogate material model under the MMC topology optimization framework to improve the accuracy of topology optimization.The proposed BER model can reconstruct the boundary elements by refining the local meshes and obtaining new nodes in boundary elements.Then the density of boundary elements is recalculated using the new node information,which is more accurate than the original model.Based on the new density of boundary elements,the material properties and volume information of the boundary elements are updated.Compared with other finite element analysis methods,the BER model is simple and feasible and can improve computational accuracy.Finally,the effectiveness and superiority of the proposed method are verified by comparing it with the optimization results of the original surrogate material model through several numerical examples.展开更多
On the stone-paved lanes of Songyang County that date back to ancient times,morning mist lingered as a faint fragrance of tea wafted from a century-old house.Inside,Yang Junjie,a tea maker born in the 1980s,worked def...On the stone-paved lanes of Songyang County that date back to ancient times,morning mist lingered as a faint fragrance of tea wafted from a century-old house.Inside,Yang Junjie,a tea maker born in the 1980s,worked deftly at the stove,his hands moving swiftly over the scorching iron wok as tender green tea leaves dance between his fingers.展开更多
Fig.3.(a)α-particle energy spectra,and(b)decay-time distributions on a logarithmic scale for the observed 288Mc and its descendant nuclei.In the panel(a),the red histograms show the observed full-energy events,while ...Fig.3.(a)α-particle energy spectra,and(b)decay-time distributions on a logarithmic scale for the observed 288Mc and its descendant nuclei.In the panel(a),the red histograms show the observed full-energy events,while the corresponding blue histograms show the reconstructed events.The red smooth curves in panel(b)are the expected time distributions according to the corresponding half-lives extracted from this work.展开更多
The deformation characteristics and activation mechanisms of kink bands in refractory multi-principal element alloys with local chemical fluctuations(LCFs)were systematically studied.These alloys were fabricated using...The deformation characteristics and activation mechanisms of kink bands in refractory multi-principal element alloys with local chemical fluctuations(LCFs)were systematically studied.These alloys were fabricated using laser-directed energy deposition technology and characterized by room-temperature compression testing,electron backscatter diffraction(EBSD),transmission electron microscopy(TEM),and high-angle annular dark-field(HAADF)imaging.The results reveal that kinking is a gradual rotational diffusion process,during which the misorientation difference between the kink and the matrix varies.A low Schmid factor is a prerequisite for kink excitation.The slip system closest to the loading axis is passively activated by the applied external force,leading to the accumulation of geometrically necessary dislocations(GNDs)required for lattice rotation.The widespread LCFs within the matrix reduce the migration rate of edge dislocations,promoting GND accumulation and enhancing the propensity for kink band formation.During deformation,the occurrence of kinking enables continuous lattice rotation to accommodate the exceptionally high strain in the vicinity,when the stress concentration in the primary kink cannot be fully released,double kinks are activated to reduce strain energy.展开更多
The microstructure and mechanical properties of Ti-Zr deoxidized low carbon microalloyed steel after‘quenching+tempering’(Q+T)and‘quenching+intercritical quenching+tempering’(Q+IQ+T)heat treatment were analyzed us...The microstructure and mechanical properties of Ti-Zr deoxidized low carbon microalloyed steel after‘quenching+tempering’(Q+T)and‘quenching+intercritical quenching+tempering’(Q+IQ+T)heat treatment were analyzed using the metallographic microscope,scanning electron microscope,electron probe microanalyzer,electronic universal testing machine and impact testing machine.The effect of element segregation band after hot rolling on the anisotropy of microstructure and mechanical properties of subsequent heat treatment was investigated.The results show that the essence of improving the banded structure by oxide metallurgy technology in the hot rolling process is to promote the formation of intragranular ferrite to break the bainite band,but the element segregation band produced during hot rolling will be inherited to the subsequent heat treatment process.After Q+T heat treatment,the microstructure is mainly martensite,and there is no obvious banded structure.The shear transformation of martensite weakens the influence of alloying element segregation and avoids the directionality of microstructure and the anisotropy of mechanical properties.After Q+IQ+T heat treatment,the martensite/ferrite bands or continuous martensite bands appear in the microstructure,and with the increase in intercritical quenching temperature,continuous martensite bands become more obvious.The appearance of banded structure aggravates the difference of mechanical properties in all directions,especially the difference of plasticity and toughness in longitudinal and transverse directions.Therefore,the banded structure can be avoided by regulating the nucleation rate difference between the element enrichment and depleted zones during the heat treatment process.The alloying elements segregation is a necessary condition for the formation of banded structure after heat treatment,but it is not a sufficient condition.展开更多
基金National Natural Science Foundation of China(52071065)Fundamental Research Funds for the Central Universities(N2007007)+2 种基金Joint Fund of Henan Province Science and Technology R&D Program(N225200810040)High-Level Talent Research Start-Up Project Funding of Henan Academy of Sciences(N242017003)Liaoning Provincial Department of Education Basic Research Projects for Colleges and Universities(LJ212410142093)。
文摘The effect of trace addition of 0.1wt%Y on the grain refinement and mechanical properties of Al-2.2Li-1.5Cu-0.5Mg-1Zn-0.2Zr-0.2Sc alloys at as-cast and heat-treated states was investigated.Results show that the addition of 0.1wt%Y into the Al-2.2Li-1.5Cu-0.5Mg-1Zn-0.2Zr-0.2Sc alloys can elevate the nucleation temperature of the Al_(3)(Sc,Zr)phase,leading to the preferential precipitation of the Al_(3)(Sc,Zr)phase and increasing the amount of Al_(3)(Sc,Zr)phase in the matrix.Al_(3)(Sc,Zr)phase can also act as a heterogeneous nucleation site in theα-Al matrix to promote nucleation and refine grains.The addition of element Y changes the precipitation phase characteristics at the grain boundaries in the as-cast alloy,which changes the distribution characteristics of secondary phases from initially continuous and coarse strip-like distribution at grain boundaries into the discontinuous dot-like and rod-like distribution.Besides,the size of secondary phases becomes smaller and their amount increases.Under the combined effects of grain refinement strengthening and precipitation strengthening,the Al-2.2Li-1.5Cu-0.5Mg-1Zn-0.2Zr-0.2Sc-0.1Y alloy after 175℃/10 h aging treatment achieves an ultimate tensile strength of 412 MPa and an elongation of 6.3%.Compared with those of the alloy without Y addition,the ultimate tensile strength and elongation of the added alloy increase by 16.1%and 53.7%,respectively.
文摘In modern ZnO varistors,traditional aging mechanisms based on increased power consumption are no longer relevant due to reduced power consumption during DC aging.Prolonged exposure to both AC and DC voltages results in increased leakage current,decreased breakdown voltage,and lower nonlinearity,ultimately compromising their protective performance.To investigate the evolution in electrical properties during DC aging,this work developed a finite element model based on Voronoi networks and conducted accelerated aging tests on commercial varistors.Throughout the aging process,current-voltage characteristics and Schottky barrier parameters were measured and analyzed.The results indicate that when subjected to constant voltage,current flows through regions with larger grain sizes,forming discharge channels.As aging progresses,the current focus increases on these channels,leading to a decline in the varistor’s overall performance.Furthermore,analysis of the Schottky barrier parameters shows that the changes in electrical performance during aging are non-monotonic.These findings offer theoretical support for understanding the aging mechanisms and condition assessment of modern stable ZnO varistors.
基金supported by Japan Society for the Promotion of Science(JSPS),a Grant-in-Aid for Scientific Research(B)(JP23K23398)(for M.G.)and(JP24K01570)(for K.T.).
文摘In this review,the synthesis,functions,and applications of the polymers containing germanium and tin,which are heavy group 14 elements,in their polymer frameworks are summarized.Germanium and tin can form similar skeletal structures with their homologues carbon and silicon,whereas the polymers containing germanium and tin show unique properties derived from their large atomic radii and weak binding energies.For example,polygermane and polystannane exhibited light absorption in the UV–visible region and conductivity because of theσ-conjugation through the polymer main-chain constructed byσ-bonds between heavy elements.Theσ-conjugation was affected by the conformational change of the polymer main-chain,and thermochromic properties can be induced.Furthermore,the weak bonds were able to be cleaved homolytically upon photoirradiation,and radicals were subsequently generated.By incorporating hypervalent heavy elements into theπ-conjugated system,it was possible to modulate the electronic structures of theπ-conjugated system throughσ*–π*conjugation with highly coordinated elements.Finally,applications for organic solar cells,organic lightemitting materials,and chemical sensors have been achieved.Herein,representative synthetic methods and unique properties for creating smart materials with germanium and tin will be explained.
基金financially supported by the National Natural Science Foundation of China(grant no.42120104005)Guizhou Provincial 2021 Science and Technology Subsidies(grant no.GZ2021SIG)+1 种基金Guizhou Provincial Science and Technology Projects(grant nos.ZK[2024]087GCC[2023]060)。
文摘The Martian core mainly contains iron,nickel and some light elements.However,controversies remain about the structure and chemical composition of the Martian core due to a lack of samples and marsquake data.Recently,the InSight lander collected long-term marsquake data,which improved the Martian interior structure model.B ased on the preliminary analysis of marsquake data,Mars has a molten liquid core with a radius of around 1700 km.As the Martian core has a smaller density and lower temperature than pure iron at corresponding pressure and temperature conditions,some light elements are introduced to reduce the density and liquidus temperature.With various methods for seismic analysis,in-situ high-pressure and high-temperature experiments,and first-principal calculations,the Martian core composition and evolution models have been updated in the past few years.Here,we review those studies on the light elements in the Martian core from four aspects including(1)high-temperature and high-pressure experiments,(2)marsquake data,(3)mineral physics model with molecular dynamics simulations and(4)cosmochemistry investigation.We discussed the effect of different light elements on the Martian core s density,sound velocity and liquidus temperature.Moreover,the review examines the varieties,abundances and forms of light elements in the Martian core.
基金jointly supported by grants from the National Natural Science Foundation of China(324B2064 and 32272799)the Fundamental Research Funds for the Central Universities,China(226-2024-00052)。
文摘Maintaining optimal crop nutritional levels is crucial for maximizing yield and enhancing stress resistance.In addition to the 17 essential nutrients,there are many plant-beneficial elements:silicon,aluminum,selenium,titanium,iodine,vanadium,cobalt,sodium,and rare earth elements.They are not essential for all plants,but some are crucial for specific plant species.However,the mechanisms of action of many beneficial elements are still unclear,and products containing beneficial elements have not been widely accepted and used by the public.This review systematically summarizes the current knowledge of plant-beneficial elements.Most importantly,we offer suggestions for future research on beneficial elements,which include integrating cross-disciplinary and innovative technologies,expanding the scope of application and elemental spies,broadening the spatial and temporal scales of research,incorporating beneficial elements into the soil health evaluation system,and shifting from single to multi-element applications.In the future,research on beneficial elements should be closely centered around“mechanism+application”to meet the ever-increasing demands driven by population growth,improve human health,tackle environmental challenges,and promote rural economic development.
基金supported by the National Natural Science Foundation of China(No.22261026).
文摘A novel method for the synthesis of 2,4-disubstituted thiophenes via the reactions of N,N-disubstituted enaminones and elemental sulfur is developed.By simply heating the substrates in pure water in the presence of NaOH,the thiophene annulation practically takes place via the generation of one C-C and two C-S bonds via cascade dual C-H functionalization and C-N bond thiolation without using any transition metal reagent.
基金National Natural Science Foundation of China (Nos.22071185 and 22271224)the Fundamental Research Funds for the Central Universities (No.2042019kf0008)Wuhan University startup funding for financial support。
文摘The development of catalytic multicomponent reactions for constructing complex organic scaffolds from readily accessible commodity chemicals is a key pursuit in contemporary synthetic chemistry.Current methods for synthesizing thioesters primarily rely on the acylation of thiols,which produces substantial waste and requires malodorous,unstable sulfur sources.In this work,we introduce a photocatalyzed hydrogen transfer strategy that enables a three-component synthesis of thioesters using abundant primary alcohols,easily available alkenes and elemental sulfur under mild conditions.This protocol demonstrates broad applicability and high chemo-and regioselectivity for both primary alcohols and alkenes,highlighting the advantage and potential of photo-mediated hydrogen transfer in facilitating multicomponent reactions using primary alcohol and elemental sulfur feedstocks.
文摘Organic-rich sediments represent vital components of Earth's geochemical cycles, acting both as potential hydrocarbon and coal reservoirs and as unconventional archives for critical metals such as rare earth elements(REEs). With the growing emphasis on clean energy technologies, the Cenozoic organic deposits of India have gained renewed significance;however, those from the southern state of Kerala remain understudied. This study investigates lignite and associated carbonaceous sediments from the Cheruvathur and Warkalli Formations using a multi-proxy approach integrating organic petrography,infrared spectroscopy, stable carbon isotopes, and REE geochemistry. The lignite exhibits huminite dominance with Type Ⅲ kerogen, deposited in a wet, mesotropic bog forest swamp under anoxic conditions. The mineral assemblage, dominated by kaolinite, quartz, illite, montmorillonite, feldspar,and pyrite/marcasite, reflects strong chemical alteration in a reducing environment. The δ^(13)C values(-25.1 to-27.3) indicate a C_(3) angiosperm source and deposition in tropical to subtropical swamp settings. REE patterns reveal LREE enrichment in carbonaceous shales and HREE enrichment in lignite,with distinct Ce, Eu, and Gd anomalies associated with provenance and redox conditions. The findings provide new insights into the paleoenvironmental evolution of Kerala's Cenozoic basins and highlight their potential as unconventional REE-bearing resources in the context of the global energy transition.
文摘Against the backdrop of profound restructuring in the global industrial and supply chains,data elements have emerged as a critical force driving the transformation of enterprises'new quality productive forces.To address the ambiguity surrounding its micro-level empowerment mechanism,this paper empirically examines the impact of data elements on enterprises'new quality productive forces and its transmission channels using panel data of Chinese A-share listed firms from 2014 to 2023.The results show that data elements significantly improve the level of enterprises'new quality productive forces.Heterogeneity analysis indicates that this promotional effect is more pronounced in non-state-owned enterprises,large-scale enterprises,and low-leverage enterprises.Mechanism tests confirm that data elements empower new quality productive forces through three paths:enhancing enterprise innovation capability,improving internal operational efficiency,and promoting inter-firm collaboration efficiency.This study provides empirical evidence for understanding the micro-level empowerment logic of data elements and offers theoretical references and practical implications for advancing the deep integration of the digital economy and the real economy.
基金financial support from the National Key Research and Development Project of China(No.2019YFA0705300)the National Natural Science Foundation of China(No.52004051)+1 种基金the Project of Zhongyuan Critical Metals Laboratory,China(No.GJJSGFYQ202321)the Fund for Priority Support of Research Projects by Returned Overseas Scholars in Henan Province,China。
文摘The influence of varying levels of impurity elements on the hot corrosion resistance of the DD98M alloy in Na_(2)SO_(4)+NaCl salt at 950℃ was investigated.The results indicate that the corrosion resistance of the DD98M alloy significantly decreases with an increase in impurity content,and the presence of nitrogen leads to an increase in alloy porosity.These porosities promote the rapid diffusion of molten salt and oxygen into the alloy,resulting in a bilateral diffusion of oxygen and sulfur,which leads to an accumulation of these elements at the oxide−matrix interface.This process contributes to the formation and propagation of interfacial cracks.A growth model was developed for hot corrosion products in alloys with varying impurity elements.
基金supported by the Tianjin Education Commission Research Program Project(No.2024KJ105)。
文摘The buoyancy-induced flow constitutes a core scientific issue for thermal management of electronic devices and thermal design of energy systems,where accurate characterization of flow and heat transfer is essential to improve thermal efficiency.In this work,buoyancy-induced flow above two heating elements flush-mounted at the bottom of a square enclosure containing air is numerically investigated over a range of Rayleigh numbers(0<Ra≤1.5×10^(8)),with a focus on equal and unequal heat flux conditions under a constraint of constant total thermal energy input.Distinct flow transitions are observed in both cases,leading to the identification of three flow regimes:Steady,periodic unsteady,and chaotic unsteady.Two types of periodic flows are distinguished,in which the first is a periodic flow dominated by a fundamental frequency(FF)and its integer-multiple frequencies(INTMF),while the second is a more complex periodic flow featuring FF,INTMF,and their sub-harmonics.The transitions between these regimes are affected by the relative heat flux of the two heaters.When the heat flux of the two heaters is unequal,the range of Rayleigh numbers corresponding to periodic flow is suppressed.It is also found that the time-averaged maximum temperature of the strong heater increases more rapidly with Ra,while that of the weak heater increases more slowly,reflecting the interaction between buoyancy-driven flow dynamics and asymmetric heat input.Analysis of the time-averaged Nusselt number demonstrates that heat dissipation from the isothermal walls remains roughly equivalent,even when the heat flux of the two heaters differs by a factor of two.These findings highlight the critical roles of Rayleigh number,the number of heaters,and the heat flux ratio of the heaters in determining heat transfer and flow characteristics for buoyancy-driven convection systems,providing important theoretical support and design references for engineering scenarios such as electronic devices and design of new energy systems.
文摘This study develops a surrogate super-resolution(SR)framework that accelerates finite element method(FEM)-based computational fluid dynamics(CFD)using deep learning.High-resolution(HR)FEM-based CFDremains computationally prohibitive for time-sensitive applications,including patient-specific aneurysm hemodynamics where rapid turnaround is valuable.The proposed pipeline learns to reconstruct HR velocity-magnitude fields fromlow-resolution(LR)FEM solutions generated under the same governing equations and boundary conditions.It consistsof three modules:(i)offline pre-training of a residual network on representative vascular geometries;(ii)lightweightfine-tuning to adapt the pretrained model to geometric variability,including patient-specific aneurysm morphologies;and(iii)an unstructured-to-structured sampling strategy with region-of-interest upsampling that concentrates resolution in flow-critical zones(e.g.,the aneurysm sac)rather than the full domain.This targeted reconstruction substantiallyreduces inference and post-processing cost while preserving key HR flow features.Experiments on cerebral aneurysmmodels show that HR velocity-magnitude fields can be recovered with accuracy comparable to direct HR simulationsat less than 1%of the direct HR simulation cost per analysis(LR simulation and SR inference),while adaptation to newgeometries requires only lightweight fine-tuning with limited target-specific HR data.While clinical endpoints andadditional variables(e.g.,pressure or wall-based metrics)are left for future work,the results indicate that the proposedsurrogate SR approach can streamline FEM-based CFD workflows toward near real-time hemodynamic analysis acrossmorphologically similar vascular models.
基金supported by the National Natural Science Foundation of China(12401482)the second author was supported by the National Natural Science Foundation of China(12371371,12261160361,11971366)supported by the Open Research Fund of Hubei Key Laboratory of Computational Science,Wuhan University.
文摘A new quadrilateral edge element method is proposed and analyzed for Maxwell equations.This proposed method is based on Duan-Liang quadrilateral element(Math.Comp.73(2004),pp.1–18).When applied to the eigenvalue problem,the method is spectral-correct and spurious-free.Stability and error estimates are obtained,including the interpolation error estimates and the error estimates between the finite element solution and the exact solution.The method is suitable for singular solution as well as smooth solution,and consequently,the method is valid for nonconvex domains which may have a number of reentrant corners.Of course,the method is suitable for arbitrary quadrilaterals(under the usual shape-regular condition).
基金supported by National Science and Technology Major Project(2025ZD0618901)National Natural Science Foundation of China(U2241245 and 52321001)+2 种基金Aeronautical Science Foundation of China(2022Z053092001)Natural Science Foundation of Shenyang(23-503-6-05)Science and Technology Major Project of Liaoning Province(2024JH1/11700028).
文摘Effects of alloying elements Ni,Co,Mn,Cr,and H on the stacking fault energy(SFE)ofγ-Fe and its microscopic mechanisms were systematically investigated.Generalized SFE calculations show that individual alloying elements Ni,Co,and H increase SFE ofγ-Fe,whereas Mn and Cr decrease SFE.The influence of alloying elements on SFE exhibits short-range characteristics.The effect of synergistic interaction of alloying elements and H on SFE was further investigated.Results show that the co-alloying of Ni/Co with H exacerbates the effect of H on the increase in SFE.In contrast,the synergistic effect of Mn/Cr with H tends to inhibit H from the increasing SFE.Finally,the electronic structure analysis elucidated the microscopic mechanism of the change in SFE.Alloying elements modulate SFE by changing the interatomic charge density at the stacking fault plane and the density of states of the stacking fault structure at the Fermi level.The present results add to the knowledge of alloying related influence on the mechanical property and hydrogen embrittlement ofγ-Fe.
基金financially supported by the National Key Research and Development Program of China (Nos.2023YFB3710401 and 2023YFB3710403)the State KeyLaboratory for Advanced Metals and Materials.
文摘This study investigates the effect of Ce content on the hydrogen storage properties of Ti_(0.98)Zr_(0.02)Mn_(1.5)Cr_(0.05)V_(0.43)Fe_(0.09)Ce_(x)(x=0,0.02,0.04,and 0.06,at%)alloys.Microstructural analysis of these alloys revealed dendritic microstructures without the segregation of chemical elements,with the C14 Laves phase identified as the dominant phase.After two activation cycles at 4 MPa and 293 K,the alloys exhibited excellent hydrogen absorption properties.The addition of Ce significantly improved the kinetics of the alloys.At x=0.02,the hydrogen absorption capacity reached 90%of its maximum within 137 s at 293 K.Pressure-composition-temperature curves indicated that hydrogen absorption capacity initially increased first and then decreased with increasing Ce content,reaching a maximum value of 1.85wt%at x=0.04.Thermodynamic results demonstrated that the enthalpy and entropy of hydrogen absorption followed a similar trend,which was consistent with the variation in hydrogen storage capacity.Thus,the improvement in hydrogen absorption capacity due to the addition of Ce is attributed to the increase in enthalpy.The increase of the lattice constant in the C14 Laves phase and the deoxidization effect of Ce are expected to be beneficial for the improvement of hydrogen absorption kinetics.
基金supported by the Science and Technology Research Project of Henan Province(242102241055)the Industry-University-Research Collaborative Innovation Base on Automobile Lightweight of“Science and Technology Innovation in Central Plains”(2024KCZY315)the Opening Fund of State Key Laboratory of Structural Analysis,Optimization and CAE Software for Industrial Equipment(GZ2024A03-ZZU).
文摘The moving morphable component(MMC)topology optimization method,as a typical explicit topology optimization method,has been widely concerned.In the MMC topology optimization framework,the surrogate material model is mainly used for finite element analysis at present,and the effectiveness of the surrogate material model has been fully confirmed.However,there are some accuracy problems when dealing with boundary elements using the surrogate material model,which will affect the topology optimization results.In this study,a boundary element reconstruction(BER)model is proposed based on the surrogate material model under the MMC topology optimization framework to improve the accuracy of topology optimization.The proposed BER model can reconstruct the boundary elements by refining the local meshes and obtaining new nodes in boundary elements.Then the density of boundary elements is recalculated using the new node information,which is more accurate than the original model.Based on the new density of boundary elements,the material properties and volume information of the boundary elements are updated.Compared with other finite element analysis methods,the BER model is simple and feasible and can improve computational accuracy.Finally,the effectiveness and superiority of the proposed method are verified by comparing it with the optimization results of the original surrogate material model through several numerical examples.
文摘On the stone-paved lanes of Songyang County that date back to ancient times,morning mist lingered as a faint fragrance of tea wafted from a century-old house.Inside,Yang Junjie,a tea maker born in the 1980s,worked deftly at the stove,his hands moving swiftly over the scorching iron wok as tender green tea leaves dance between his fingers.
文摘Fig.3.(a)α-particle energy spectra,and(b)decay-time distributions on a logarithmic scale for the observed 288Mc and its descendant nuclei.In the panel(a),the red histograms show the observed full-energy events,while the corresponding blue histograms show the reconstructed events.The red smooth curves in panel(b)are the expected time distributions according to the corresponding half-lives extracted from this work.
文摘The deformation characteristics and activation mechanisms of kink bands in refractory multi-principal element alloys with local chemical fluctuations(LCFs)were systematically studied.These alloys were fabricated using laser-directed energy deposition technology and characterized by room-temperature compression testing,electron backscatter diffraction(EBSD),transmission electron microscopy(TEM),and high-angle annular dark-field(HAADF)imaging.The results reveal that kinking is a gradual rotational diffusion process,during which the misorientation difference between the kink and the matrix varies.A low Schmid factor is a prerequisite for kink excitation.The slip system closest to the loading axis is passively activated by the applied external force,leading to the accumulation of geometrically necessary dislocations(GNDs)required for lattice rotation.The widespread LCFs within the matrix reduce the migration rate of edge dislocations,promoting GND accumulation and enhancing the propensity for kink band formation.During deformation,the occurrence of kinking enables continuous lattice rotation to accommodate the exceptionally high strain in the vicinity,when the stress concentration in the primary kink cannot be fully released,double kinks are activated to reduce strain energy.
基金supported by the National Natural Science Foundation of China(No.52304358)Young Elite Scientists Sponsorship Program by CAST(No.YESS20230462).
文摘The microstructure and mechanical properties of Ti-Zr deoxidized low carbon microalloyed steel after‘quenching+tempering’(Q+T)and‘quenching+intercritical quenching+tempering’(Q+IQ+T)heat treatment were analyzed using the metallographic microscope,scanning electron microscope,electron probe microanalyzer,electronic universal testing machine and impact testing machine.The effect of element segregation band after hot rolling on the anisotropy of microstructure and mechanical properties of subsequent heat treatment was investigated.The results show that the essence of improving the banded structure by oxide metallurgy technology in the hot rolling process is to promote the formation of intragranular ferrite to break the bainite band,but the element segregation band produced during hot rolling will be inherited to the subsequent heat treatment process.After Q+T heat treatment,the microstructure is mainly martensite,and there is no obvious banded structure.The shear transformation of martensite weakens the influence of alloying element segregation and avoids the directionality of microstructure and the anisotropy of mechanical properties.After Q+IQ+T heat treatment,the martensite/ferrite bands or continuous martensite bands appear in the microstructure,and with the increase in intercritical quenching temperature,continuous martensite bands become more obvious.The appearance of banded structure aggravates the difference of mechanical properties in all directions,especially the difference of plasticity and toughness in longitudinal and transverse directions.Therefore,the banded structure can be avoided by regulating the nucleation rate difference between the element enrichment and depleted zones during the heat treatment process.The alloying elements segregation is a necessary condition for the formation of banded structure after heat treatment,but it is not a sufficient condition.
