A major problem facing the magnesium melting process is to address the oxidative combustion of magnesium.At present,there are still some problems in the method used to protect magnesium smelting.For example,the reacti...A major problem facing the magnesium melting process is to address the oxidative combustion of magnesium.At present,there are still some problems in the method used to protect magnesium smelting.For example,the reaction of covering flux with magnesium melt is likely to produce a large number of toxic and harmful gasses(Cl_(2) and HCl),the cost of such reaction is high,and there is a lack of clarity on the protection mechanism of CO_(2) acting as the protective gas of magnesium melt.Therefore,a new process is proposed in this paper to isolate the air on the surface of magnesium melt using MgO-C-Mg film.Based on the thermodynamic theory of MgO-C-Mg film formation during crude magnesium smelting,an investigation is conducted into the effect of different experimental conditions on the protective effect of magnesium.Not only is the protective mechanism of MgO-C-Mg film revealed,it is also verified that the MgO-C-Mg film can produce a more pronounced protective effect at suitable temperature.According to thermodynamic analysis,magnesium melt reacts with CO_(2) to form magnesium oxide and C.CO_(2) consumes C when the experimental temperature exceeds 700℃.This is contrary to the purpose of the experiment as it should be maintained at about 700℃.The experimental results show that an obvious protective effect can be produced on the magnesium melt by the MgO-C-Mg film generated under the following conditions of 90%CO_(2)-10%Ar,smelting temperature of 700℃,holding time of 60 min,and stirring time of 20 min.展开更多
The manufacture and obsolescence of smartphones produce numerous waste plastic accessories(e.g.,waste smartphone protective film(WSPF)),possessing immense potential for recycling.However,available recycling technologi...The manufacture and obsolescence of smartphones produce numerous waste plastic accessories(e.g.,waste smartphone protective film(WSPF)),possessing immense potential for recycling.However,available recycling technologies have limitations such as substrate damage and secondary pollutant generation.The present study aimed to develop a green disposal method that not only recycled polyethylene terephthalate(PET)from WSPF,but also reused the stripped polyacrylate(PAA)adhesive as an adsorbent to reduce solid waste generation.When the WSPF was treated in 1 mol/L NaOH solution at 90°C,the PAA hydrolyzed to two main by-products of 1-butanol and 2-ethylhexanol,weakening the binding strength between PAA and PET and then efficient separation of them.Further bench-scale test revealed that over 97.2%of detachment efficiency toward PAA was achieved during continuous treatment of 17 batches of WSPF(200 g for each)without supplement of NaOH and generation of wastewater.Meanwhile,the economic evaluation indicated that the recycling method would generate a net profit margin of 647%for the second year without considering the incurrence of new cost and input.Additionally,the pyrolysis of waste PAA enabled its conversion into potential adsorbent,which showed 2 to 4 times enhanced adsorption capacity toward styrene and ethyl acetate after modification with NaOH solution.This study provides a green method for recycling waste plastics and inspires a referable solution for solid waste treatment in the smartphone industry.展开更多
Electrochemical techniques, X-ray diffraction （XRD）, and scanning electron microscopy （SEM） were applied to study the corrosion behaviors of X65 steel in static solution with carbon dioxide （CO2） at 65℃. The re...Electrochemical techniques, X-ray diffraction （XRD）, and scanning electron microscopy （SEM） were applied to study the corrosion behaviors of X65 steel in static solution with carbon dioxide （CO2） at 65℃. The results show that iron carbonate （FeCO3） deposits on the steel surface as a corrosion product scale. This iron carbonate scale acts as a barrier to CO2 corrosion, and can reduce the general corrosion rate. The protection ability of the scale is closely related to the scale morphological characteristics.展开更多
Surface films that formed on molten AZ91D magnesium alloy in S02/air cover gases at 680 ℃ in a sealed furnace were characterized by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and ...Surface films that formed on molten AZ91D magnesium alloy in S02/air cover gases at 680 ℃ in a sealed furnace were characterized by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and Auger electron spectroscopy. It is revealed that the film formed on molten AZ91D alloy surface in cover gas with high air content can prevent the molten AZ91D alloy from oxidation and ignition. The surface film contained three elements, namely magnesium, oxygen and sulfur, and was mainly composed of MgO and MgS. The properties of the film depended on air content in the cover gas and holding time. Thermodynamic calculation showed that MgSO4 was the stable phase, and it was concluded that the formation of MgS04 was important for the formation of the protective surface film in S02/air atmospheres.展开更多
The electrochemical behaviors of high temperature oxide film formed on the sputtered microcrystalline coating of M38 alloy （mc-M38） were investigated by potentiodynamic and electrochemical impedance spectroscopy （...The electrochemical behaviors of high temperature oxide film formed on the sputtered microcrystalline coating of M38 alloy （mc-M38） were investigated by potentiodynamic and electrochemical impedance spectroscopy （EIS） techniques in 3.5% NaCl solution. Mott-Schottky analysis was used to study the semi-conductive properties of the surface oxide. The results of the capacitance measurements showed that the oxide films on both the coating and the cast alloy were p-type semiconducting characteristics. Both the carrier density （Na）and the flat band potential （Efb） were obviously frequency-dependent, and the optimal frequency range was from 1000 to 1500 Hz. The oxidized coating exhibited higher protectivity than the oxidized cast alloy due to the lower carrier density compared with that of the oxidized cast alloy. The EIS data of the long-term immersing tests suggested that the oxide film served as an inner-barrier layer against chloride ions. The penetration of the aggressive ions into the surface oxide resulted in the decreased polarization resistance as a function of the immersion time.展开更多
At present, the main attention of researchers is paid to the deterioration of heat transfer when heating the outer surface of the pipe with the liquid or steam, flowing inside it, in the presence of films or deposits ...At present, the main attention of researchers is paid to the deterioration of heat transfer when heating the outer surface of the pipe with the liquid or steam, flowing inside it, in the presence of films or deposits on its inner surface. However, when pipe is heating by heat carrier medium, flowing inside it, film on the inner pipe surface serve a dual protective function, protecting the pipe from corrosion and reducing its thermal stress. The article represents the results of the computational analysis of protective films influence on the thermal stressed state of headers and steam pipelines of combined-cycle power plants (CCPP) heat-recovery steam generators at different transient operating conditions particularly at startups from different initial temperature states and thermal shock. It is shown that protective films have a significant influence on the stresses magnitude and damage accumulation mainly for great temperature disturbances (for thermal shock). Calculations were carried out at various thicknesses of films and assuming that their thermal conductivity less than thermal conductivity of the steam pipelines metal.展开更多
An explosive blast mitigation alternative has increased the safety of structures by using " catcher" systems. These systems " catch" or repel the failure of the window or in-fill wall pro-tecting l...An explosive blast mitigation alternative has increased the safety of structures by using " catcher" systems. These systems " catch" or repel the failure of the window or in-fill wall pro-tecting life and property from ballistic shards or fragments. They can be designed to be stand-alone in new construction and structural retrofits or used to augment structural hardening tech-niques. Cables, fabrics, and thin gauge sheet steel are examples of catcher systems used in the past. A new and evolving category of catcher systems are based on polymeric materials that can be used for both wall and window upgrades. These products are a proven blast mitigation concept and K&C Protective Technologies Pte Ltd (KCPT) together with Sherwin-Williams(SW) use KCPT′s blast engineering capacity and SW′s material engineering principles to create engineered systems for even greater in-use performance.展开更多
The phosphate protective film and micro-galvanic corrosion of biological Mg-3Zn-xNd (x = 0, 0.6, 1.2) alloys were investigated by scanning and transmission electron microscopy, quasi-in-situ observation, scanning Kelv...The phosphate protective film and micro-galvanic corrosion of biological Mg-3Zn-xNd (x = 0, 0.6, 1.2) alloys were investigated by scanning and transmission electron microscopy, quasi-in-situ observation, scanning Kelvin probe force microscopy (SKPFM) and electrochemical tests. The results revealed the Mg-Zn-Nd phases formed in Mg-3Zn alloy contained with Nd. Adding Nd resulted in a significant decline in the cracks of the phosphate protective film and micro-galvanic corrosion of alloys, which were recorded by quasi-in-situ observation. In addition, the Volta potential difference of Mg-Zn-Nd/α-Mg (~ 188 mV) was lower than MgZn/α-Mg (~ 419 mV) and Zn-rich/α-Mg (~ 260 mV), and the corrosion rates of alloys markedly decreased after the addition of 0.6 wt% Nd. The improvement in corrosion resistance of Nd-containing alloys was mainly attributed to the following: (i) the addition of Nd reduced the Volta potential difference (second phases/α-Mg);(ii) the phosphate protective film containing Nd_(2)O_(3) deposited on the surface of the alloys, effectively preventing the penetration of harmful anions.展开更多
The development of Chinese agriculture is now facing the grim situation of decreasing farmland area, increasing population and social demands, so the devel- opment of protected horticulture becomes necessary to solve ...The development of Chinese agriculture is now facing the grim situation of decreasing farmland area, increasing population and social demands, so the devel- opment of protected horticulture becomes necessary to solve the issue. This paper reviewed the characteristics of traditional horticulture films and application prospects of new functional films.展开更多
In this work,a method to improve the protection against corrosion of porous sintered stainless steel is presented.It is based on the electrodeposition of polypyrrole(PPy)layers doped with a large size counterion such ...In this work,a method to improve the protection against corrosion of porous sintered stainless steel is presented.It is based on the electrodeposition of polypyrrole(PPy)layers doped with a large size counterion such as dodecylbenzenesulphonic acid(DBSA),a conducting polymer with high corrosion resistance and good biocompatibility.The efficacy of PPy coating depends on the adequate adhesion between the metal substrate and the coating layer.The protection against corrosion has been tested using 316 L stainless steel(SS)powder sintered at different conditions to evaluate the effect of the sintering atmosphere(nitrogen and vacuum)and cooling rates(furnace and water)on corrosion resistance,while wrought 316 L SS has been used as reference material.In addition,two electrochemical deposition techniques have been tested to select the most adequate.Open circuit potential evolution,anodic polarization measurements and electrochemical impedance spectra have been used to evaluate corrosion protection in phosphate buffer saline medium.It has been evidenced that a more homogeneous and stable coating was obtained in the case of porous stainless steel.The corrosion potential shifted to nobler values and the anodic polarization branch became more stable.Coated porous samples have a good passivation performance with a lower stable passive current density and a higher breakdown potential.The transfer electronic resistance and the impedance module increase more than one order of magnitude.Therefore,the porosity of sintered stainless steel is seen as an advantage for the improvement of the adherence of the PPy coatings.The best corrosion protection is found for samples sintered in nitrogen and water-cooled.展开更多
Vanadium films were prepared on zinc surfaces by using a solution containing vanadate. Corrosion protection properties of vanadium-treated （V-treated）, chromium-treated （Cr-treated）, and untreated zinc surfaces in...Vanadium films were prepared on zinc surfaces by using a solution containing vanadate. Corrosion protection properties of vanadium-treated （V-treated）, chromium-treated （Cr-treated）, and untreated zinc surfaces in contact with a 3.5 wt.% NaC1 solution were studied using potentiodynamic polarization, electrochemical impedance spectroscopy （EIS）, and neutral salt spray （NSS） tests. According to these results, the V-treated layer significantly improved the corrosion resistance of zinc surfaces. In comparison with the Cr-treated layer, the V-treated layer exhibited a better corrosion resistance. The composition of the V-treated layer was studied using X-ray photoelectron spectroscopy （XPS）. XPS measurements indicated that the vanadium layer formed on zinc surfaces and the vanadium-rich coating was a hydrated oxide with a composition of V2O5, VO2, and its hydrates such as V2O5.nH2O and VO（OH）2.展开更多
This paper presents the principle,properties,advantage and disadvantage,associated problems and trend of laser protection with VO 2 film for infrared detectors in the range of 3～5μm and 8～12μm regions and suggest...This paper presents the principle,properties,advantage and disadvantage,associated problems and trend of laser protection with VO 2 film for infrared detectors in the range of 3～5μm and 8～12μm regions and suggests VO 2 film is a potential protection material for infrared detectors.展开更多
ZrCoCe getter films with thickness of ~2.3 lm were deposited on Si(100) wafers by direct current(DC)magnetron sputtering process. A 400-nm-thick Pd protection layer was then deposited on the as-deposited ZrCoCe film w...ZrCoCe getter films with thickness of ~2.3 lm were deposited on Si(100) wafers by direct current(DC)magnetron sputtering process. A 400-nm-thick Pd protection layer was then deposited on the as-deposited ZrCoCe film without exposure to atmosphere. Microstructure, surface morphology and surface chemical state of the films were analyzed. Moreover, hydrogen sorption properties were determined. The results show that the ZrCoCe film displays a cauliflower-like morphology and a porous columnar-like structure which is composed of nanocrystal grains. The Pd protection layer tightly adheres to the surface of the ZrCoCe film and efficiently prevents the oxidation of Zr under exposure to atmosphere. We find that the hydrogen sorption properties of the Pd-ZrCoCe film are significantly improved,in comparison with those of the as-deposited ZrCoCe film.展开更多
To increase corrosion resistance of the sample,its electrical impedance must be increased.Due to the fact that electrical impedance depends on elements such as electrical resistance,capacitance,and inductance,by incre...To increase corrosion resistance of the sample,its electrical impedance must be increased.Due to the fact that electrical impedance depends on elements such as electrical resistance,capacitance,and inductance,by increasing the electrical resistance,reducing the capacitance and inductance,electrical impedance and corrosion resistance can be increased.Based on the fact that these elements depend on the type of material and the geometry of the material,multilayer structures with different geometries are proposed.For this purpose,conventional multilayer thin films,multilayer thin film including zigzag structure(zigzag 1)and multilayer thin film including double zigzag structure(zigzag 2)of manganese nitride are considered to protect AISI 304 stainless steel against corrosion in salt solution.These multilayer coatings including zigzag structures are prepared by alternately using the conventional deposition of thin film and glancing angle deposition method.After deposition,the samples are placed in a furnace under nitrogen flux for nitriding.The cross sections of the structures are observed by field emission scanning electron microscopy(FESEM).Atomic force microscope(AFM)is used to make surface analyses of the samples.The results show that the multilayer thin films including zigzag structures have smaller grains than conventional multilayer thin films,and the zigzag 2 structure has the smaller grain than the other two samples,which is attributed to the effect of shadowing and porosity on the oblique angle deposition method.Crystallography structures of the samples are studied by using x-ray diffraction(XRD)pattern and the results show that nitride phase formation in zigzag 2 structure is better than that in zigzag 1 structure and conventional multilayer thin film.To investigate the corrosion resistances of the structures,electrochemical impedance spectroscopy(EIS)and potentiodynamic polarization tests are performed.The results reveal that the multilayer thin films with zigzag structures have better corrosion protection than the conventional multilayer thin films,and the zigzag structure 2 has the smallest corrosion current and the highest corrosion resistance.The electrical impedances of the samples are investigated by simulating equivalent circuits.The high corrosion resistance of zigzag 2 structure as compared with conventional multilayer structure and zigzag 1 structure,is attributed to the high electrical impedance of the structure due to its small capacitance and high electrical resistance.Finally,the surfaces of corroded samples are observed by scanning electron microscope(SEM).展开更多
A Ag@CuFe_(2)O_(4)@TiO_(2) nanocomposite film with high performance of photogenerated cathodic protection was prepared by hydrothermal and photoreduction methods.The results showed that when the CuFe_(2)O_(4) hydrothe...A Ag@CuFe_(2)O_(4)@TiO_(2) nanocomposite film with high performance of photogenerated cathodic protection was prepared by hydrothermal and photoreduction methods.The results showed that when the CuFe_(2)O_(4) hydrothermal reaction time was 6 h and the AgNO_(3) concentration was 0.1 M,the Ag@CuFe_(2)O_(4)@TiO_(2) nanocomposite material performed the best cathodic protection capability for 304 stainless steel(304SS).In this case,the protective potential achieved-930 mV(versus SCE)associated with the photocurrent density of 475μA/cm^(2),which was 14.8 times that of pure TiO_(2) nanowires.In the dark,the nanocomposite provided cathodic protection of up to 485 mV for 304SS.Due to the heterogeneous junctions at the two interfaces among the three kinds of nanocomposite materials,the build-in electric field was fabricated,which promoted the separation efficiency of photogenerated electrons and holes and effectively improved the photochemical cathodic protection of 304SS.展开更多
Highly ordered Ag2 S/ZnS/ZnO nanorod array film photoanodes were prepared on a Ti substrate for photocathodic cathodic protection.The results indicated that the photoresponse range of the Ag2S/ZnS/ZnO composite film w...Highly ordered Ag2 S/ZnS/ZnO nanorod array film photoanodes were prepared on a Ti substrate for photocathodic cathodic protection.The results indicated that the photoresponse range of the Ag2S/ZnS/ZnO composite film was extended compared to those of the ZnO and ZnS/ZnO films,indicating its higher light absorption capacity.When the Ag2S/ZnS/ZnO composite film served as a photoanode,the film can provide the best effective photocathodic protection for 304 stainless steel in a 3.5 wt%NaCl solution under white light illumination compared to the ZnO and ZnS/ZnO films.Additionally,in comparison to pure ZnO film,the photocurrent for the ZnS/ZnO film remained the same without noticeable fluctuation after illumination for 1 h,indicating that the ZnS functionalization improved the stability by overcoming the photocorrosion effect of the ZnO photoanode under light irradiation.展开更多
Bi_(2)WO_(6) nanoplate/TiO_(2) nanowire and Bi_(2)WO_(6) nanoflower/TiO_(2) nanowire composite films were successfully prepared using a hydrothermal method.The results show that the light absorption for Bi_(2)WO_(6)/T...Bi_(2)WO_(6) nanoplate/TiO_(2) nanowire and Bi_(2)WO_(6) nanoflower/TiO_(2) nanowire composite films were successfully prepared using a hydrothermal method.The results show that the light absorption for Bi_(2)WO_(6)/TiO_(2) composite films is extended to the visible region after Bi_(2)WO_(6) nanoplates and nanoflowers are assembled onto TiO_(2) nanowires.Furthermore,Bi_(2)WO_(6) nanoflower/TiO_(2) nano wire composite film exhibits a better absorption property compared to Bi_(2)WO_(6) nanoplate/TiO_(2) nanowire film,which is mainly ascribed to the narrower bandgap of Bi_(2)WO_(6) nanoflower compared to that of Bi_(2)WO_(6) nanoplate.The photocurrent density for Bi_(2)WO_(6) nanoflower/TiO_(2) nanowire and Bi_(2)WO_(6) nanoplate/TiO_(2) nanowire composite films can reach 95 and 62.5 μA cm-2,respectively,which are much higher than that obtained for a pure TiO_(2) nanowire film(25 μA cm-2).Meanwhile,under illumination,the pure TiO_(2) nanowire,Bi_(2)WO_(6) nanoplate/TiO_(2) nanowire and Bi_(2)WO_(6) nanoflower/TiO_(2) nanowire films can reduce the potential of the coupled 304 stainless steel in 3.5 wt.%NaCl solution by 299,719 and 739 mV,respectively.Thus,Bi_(2)WO_(6) nanoflower/TiO_(2) nanowire film is found to provide the best effective photocathodic protection for 304 stainless steel.This work not only provides an example of shape-dependent photocathodic protection based on Bi_(2)WO_(6) but also opens up new possibilities to design an ideal microstructure on the basis of semiconductor materials for future applications of photocathodic protection.展开更多
The protective behavior for a molten AZ91D alloy in an open melting furnace was investigated under a protective gas mixture containing 3% SO2 and 97% CO2, and the protection mechanism was discussed. Experimental resul...The protective behavior for a molten AZ91D alloy in an open melting furnace was investigated under a protective gas mixture containing 3% SO2 and 97% CO2, and the protection mechanism was discussed. Experimental results show that the gas mixture provides effective protection for AZ91D melt in the temperature range from 680 ℃ to 730 ℃. The microstructure, chemical composition and phase composition of the surface film formed on the molten AZ91D alloy were analyzed using scanning electron microscopy （SEM） with energy dispersive spectrometer （EDS） and X-ray diffraction （XRD）. The SEM results demonstrate that the surface films with an average thickness between 0.5 pm and 2 pm are dense and coherent in the protected temperature range. The EDS results reveal that the surface film mainly contains elements S, C, O, AI and Mg. The XRD results show that the surface film consists of MgO, MgS and a small amount of C phase.展开更多
A kind of interlaminar film with carbon nanotubes inserted into polyether ketone with cardo was used for lightning strike protection of composite laminates. The distribution of the interlaminar film was investigated b...A kind of interlaminar film with carbon nanotubes inserted into polyether ketone with cardo was used for lightning strike protection of composite laminates. The distribution of the interlaminar film was investigated by experimental and numerical methods. Artificial lightning strike tests were conducted for 12-film carbon nanotube and traditional surface silver coating protected specimens. Then corresponding finite element models(FEMs) were established to analyze the lightning strike effect and validated by the experimental results. Based on the FEMs, the number, distribution and thickness of interlaminar film were investigated in order to obtain equivalent protection effect with the traditional surface silver coating. The results show that only the first two layers were damaged for the surface silver coating protected specimen, while 5 layers were ablated for the 12-film protected specimen. Lightning strike damage area of the laminate protected with 5-film carbon nanotube is almost the same as that of the laminate protected with 12-film carbon nanotube. Compared with traditional surface silver coating protection, one film protection with thickness of 360 lm can make the laminate to obtain equivalent damage depth, 54.8% smaller damage area and 58% less additional weight. And reparability of the laminate is better than that of the laminate protected with 5 interlaminar films.展开更多
基金supported by the Yunnan Province Nonferrous Metal Vacuum Metallurgy Top Team[grant number 202305AS350012].
文摘A major problem facing the magnesium melting process is to address the oxidative combustion of magnesium.At present,there are still some problems in the method used to protect magnesium smelting.For example,the reaction of covering flux with magnesium melt is likely to produce a large number of toxic and harmful gasses(Cl_(2) and HCl),the cost of such reaction is high,and there is a lack of clarity on the protection mechanism of CO_(2) acting as the protective gas of magnesium melt.Therefore,a new process is proposed in this paper to isolate the air on the surface of magnesium melt using MgO-C-Mg film.Based on the thermodynamic theory of MgO-C-Mg film formation during crude magnesium smelting,an investigation is conducted into the effect of different experimental conditions on the protective effect of magnesium.Not only is the protective mechanism of MgO-C-Mg film revealed,it is also verified that the MgO-C-Mg film can produce a more pronounced protective effect at suitable temperature.According to thermodynamic analysis,magnesium melt reacts with CO_(2) to form magnesium oxide and C.CO_(2) consumes C when the experimental temperature exceeds 700℃.This is contrary to the purpose of the experiment as it should be maintained at about 700℃.The experimental results show that an obvious protective effect can be produced on the magnesium melt by the MgO-C-Mg film generated under the following conditions of 90%CO_(2)-10%Ar,smelting temperature of 700℃,holding time of 60 min,and stirring time of 20 min.
基金supported by the National Natural Science Foundation of China(No.42177354)Guangzhou Basic and Applied Basic Research Scheme(No.2024A04J6358)the National Key R&D Program of China(No.2019YFC0214402).
文摘The manufacture and obsolescence of smartphones produce numerous waste plastic accessories(e.g.,waste smartphone protective film(WSPF)),possessing immense potential for recycling.However,available recycling technologies have limitations such as substrate damage and secondary pollutant generation.The present study aimed to develop a green disposal method that not only recycled polyethylene terephthalate(PET)from WSPF,but also reused the stripped polyacrylate(PAA)adhesive as an adsorbent to reduce solid waste generation.When the WSPF was treated in 1 mol/L NaOH solution at 90°C,the PAA hydrolyzed to two main by-products of 1-butanol and 2-ethylhexanol,weakening the binding strength between PAA and PET and then efficient separation of them.Further bench-scale test revealed that over 97.2%of detachment efficiency toward PAA was achieved during continuous treatment of 17 batches of WSPF(200 g for each)without supplement of NaOH and generation of wastewater.Meanwhile,the economic evaluation indicated that the recycling method would generate a net profit margin of 647%for the second year without considering the incurrence of new cost and input.Additionally,the pyrolysis of waste PAA enabled its conversion into potential adsorbent,which showed 2 to 4 times enhanced adsorption capacity toward styrene and ethyl acetate after modification with NaOH solution.This study provides a green method for recycling waste plastics and inspires a referable solution for solid waste treatment in the smartphone industry.
文摘Electrochemical techniques, X-ray diffraction （XRD）, and scanning electron microscopy （SEM） were applied to study the corrosion behaviors of X65 steel in static solution with carbon dioxide （CO2） at 65℃. The results show that iron carbonate （FeCO3） deposits on the steel surface as a corrosion product scale. This iron carbonate scale acts as a barrier to CO2 corrosion, and can reduce the general corrosion rate. The protection ability of the scale is closely related to the scale morphological characteristics.
基金supported by the Specialized Research Fund for the Doctoral Program of Higher Education under Grant No.20090002110029the High Technology Research and Development Program of China under Grant No.2009AA03Z114the MOST(Ministry of Science and Technology)of China under Grant No.2010DFA72760
文摘Surface films that formed on molten AZ91D magnesium alloy in S02/air cover gases at 680 ℃ in a sealed furnace were characterized by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and Auger electron spectroscopy. It is revealed that the film formed on molten AZ91D alloy surface in cover gas with high air content can prevent the molten AZ91D alloy from oxidation and ignition. The surface film contained three elements, namely magnesium, oxygen and sulfur, and was mainly composed of MgO and MgS. The properties of the film depended on air content in the cover gas and holding time. Thermodynamic calculation showed that MgSO4 was the stable phase, and it was concluded that the formation of MgS04 was important for the formation of the protective surface film in S02/air atmospheres.
文摘The electrochemical behaviors of high temperature oxide film formed on the sputtered microcrystalline coating of M38 alloy （mc-M38） were investigated by potentiodynamic and electrochemical impedance spectroscopy （EIS） techniques in 3.5% NaCl solution. Mott-Schottky analysis was used to study the semi-conductive properties of the surface oxide. The results of the capacitance measurements showed that the oxide films on both the coating and the cast alloy were p-type semiconducting characteristics. Both the carrier density （Na）and the flat band potential （Efb） were obviously frequency-dependent, and the optimal frequency range was from 1000 to 1500 Hz. The oxidized coating exhibited higher protectivity than the oxidized cast alloy due to the lower carrier density compared with that of the oxidized cast alloy. The EIS data of the long-term immersing tests suggested that the oxide film served as an inner-barrier layer against chloride ions. The penetration of the aggressive ions into the surface oxide resulted in the decreased polarization resistance as a function of the immersion time.
文摘At present, the main attention of researchers is paid to the deterioration of heat transfer when heating the outer surface of the pipe with the liquid or steam, flowing inside it, in the presence of films or deposits on its inner surface. However, when pipe is heating by heat carrier medium, flowing inside it, film on the inner pipe surface serve a dual protective function, protecting the pipe from corrosion and reducing its thermal stress. The article represents the results of the computational analysis of protective films influence on the thermal stressed state of headers and steam pipelines of combined-cycle power plants (CCPP) heat-recovery steam generators at different transient operating conditions particularly at startups from different initial temperature states and thermal shock. It is shown that protective films have a significant influence on the stresses magnitude and damage accumulation mainly for great temperature disturbances (for thermal shock). Calculations were carried out at various thicknesses of films and assuming that their thermal conductivity less than thermal conductivity of the steam pipelines metal.
文摘An explosive blast mitigation alternative has increased the safety of structures by using " catcher" systems. These systems " catch" or repel the failure of the window or in-fill wall pro-tecting life and property from ballistic shards or fragments. They can be designed to be stand-alone in new construction and structural retrofits or used to augment structural hardening tech-niques. Cables, fabrics, and thin gauge sheet steel are examples of catcher systems used in the past. A new and evolving category of catcher systems are based on polymeric materials that can be used for both wall and window upgrades. These products are a proven blast mitigation concept and K&C Protective Technologies Pte Ltd (KCPT) together with Sherwin-Williams(SW) use KCPT′s blast engineering capacity and SW′s material engineering principles to create engineered systems for even greater in-use performance.
基金support by the National Natural Science Foundation of China(No.51961026).
文摘The phosphate protective film and micro-galvanic corrosion of biological Mg-3Zn-xNd (x = 0, 0.6, 1.2) alloys were investigated by scanning and transmission electron microscopy, quasi-in-situ observation, scanning Kelvin probe force microscopy (SKPFM) and electrochemical tests. The results revealed the Mg-Zn-Nd phases formed in Mg-3Zn alloy contained with Nd. Adding Nd resulted in a significant decline in the cracks of the phosphate protective film and micro-galvanic corrosion of alloys, which were recorded by quasi-in-situ observation. In addition, the Volta potential difference of Mg-Zn-Nd/α-Mg (~ 188 mV) was lower than MgZn/α-Mg (~ 419 mV) and Zn-rich/α-Mg (~ 260 mV), and the corrosion rates of alloys markedly decreased after the addition of 0.6 wt% Nd. The improvement in corrosion resistance of Nd-containing alloys was mainly attributed to the following: (i) the addition of Nd reduced the Volta potential difference (second phases/α-Mg);(ii) the phosphate protective film containing Nd_(2)O_(3) deposited on the surface of the alloys, effectively preventing the penetration of harmful anions.
基金Supported by Jiangsu Agricultural Science and Technology Innovation Fund[CX(13)3032]Jiangsu Six Category Outstanding Talent(NY-031)Nanjing Innovation Fund for Small and Mediumsized Technology-based Firms(2013074)~~
文摘The development of Chinese agriculture is now facing the grim situation of decreasing farmland area, increasing population and social demands, so the devel- opment of protected horticulture becomes necessary to solve the issue. This paper reviewed the characteristics of traditional horticulture films and application prospects of new functional films.
基金financially supported by the MINECO-FEDER(No.AGL2015-67482-R)the Junta de Castilla y Leon and FEDER(No.VA275P18)Junta de Castilla y León for a grant(BOCYL-D-4112015-9).
文摘In this work,a method to improve the protection against corrosion of porous sintered stainless steel is presented.It is based on the electrodeposition of polypyrrole(PPy)layers doped with a large size counterion such as dodecylbenzenesulphonic acid(DBSA),a conducting polymer with high corrosion resistance and good biocompatibility.The efficacy of PPy coating depends on the adequate adhesion between the metal substrate and the coating layer.The protection against corrosion has been tested using 316 L stainless steel(SS)powder sintered at different conditions to evaluate the effect of the sintering atmosphere(nitrogen and vacuum)and cooling rates(furnace and water)on corrosion resistance,while wrought 316 L SS has been used as reference material.In addition,two electrochemical deposition techniques have been tested to select the most adequate.Open circuit potential evolution,anodic polarization measurements and electrochemical impedance spectra have been used to evaluate corrosion protection in phosphate buffer saline medium.It has been evidenced that a more homogeneous and stable coating was obtained in the case of porous stainless steel.The corrosion potential shifted to nobler values and the anodic polarization branch became more stable.Coated porous samples have a good passivation performance with a lower stable passive current density and a higher breakdown potential.The transfer electronic resistance and the impedance module increase more than one order of magnitude.Therefore,the porosity of sintered stainless steel is seen as an advantage for the improvement of the adherence of the PPy coatings.The best corrosion protection is found for samples sintered in nitrogen and water-cooled.
文摘Vanadium films were prepared on zinc surfaces by using a solution containing vanadate. Corrosion protection properties of vanadium-treated （V-treated）, chromium-treated （Cr-treated）, and untreated zinc surfaces in contact with a 3.5 wt.% NaC1 solution were studied using potentiodynamic polarization, electrochemical impedance spectroscopy （EIS）, and neutral salt spray （NSS） tests. According to these results, the V-treated layer significantly improved the corrosion resistance of zinc surfaces. In comparison with the Cr-treated layer, the V-treated layer exhibited a better corrosion resistance. The composition of the V-treated layer was studied using X-ray photoelectron spectroscopy （XPS）. XPS measurements indicated that the vanadium layer formed on zinc surfaces and the vanadium-rich coating was a hydrated oxide with a composition of V2O5, VO2, and its hydrates such as V2O5.nH2O and VO（OH）2.
文摘This paper presents the principle,properties,advantage and disadvantage,associated problems and trend of laser protection with VO 2 film for infrared detectors in the range of 3～5μm and 8～12μm regions and suggests VO 2 film is a potential protection material for infrared detectors.
基金financially supported by the National Natural Science Foundation of China(No.61874137)。
文摘ZrCoCe getter films with thickness of ~2.3 lm were deposited on Si(100) wafers by direct current(DC)magnetron sputtering process. A 400-nm-thick Pd protection layer was then deposited on the as-deposited ZrCoCe film without exposure to atmosphere. Microstructure, surface morphology and surface chemical state of the films were analyzed. Moreover, hydrogen sorption properties were determined. The results show that the ZrCoCe film displays a cauliflower-like morphology and a porous columnar-like structure which is composed of nanocrystal grains. The Pd protection layer tightly adheres to the surface of the ZrCoCe film and efficiently prevents the oxidation of Zr under exposure to atmosphere. We find that the hydrogen sorption properties of the Pd-ZrCoCe film are significantly improved,in comparison with those of the as-deposited ZrCoCe film.
基金Project supported by the Funds from the University of Mohaghegh Ardabili and University of Tehran and the Iran National Science Foundation(INSF)the Centre of Excellence for Physics of Structure and Microscopic Properties of Matter,Department of Physics,University of Tehran.
文摘To increase corrosion resistance of the sample,its electrical impedance must be increased.Due to the fact that electrical impedance depends on elements such as electrical resistance,capacitance,and inductance,by increasing the electrical resistance,reducing the capacitance and inductance,electrical impedance and corrosion resistance can be increased.Based on the fact that these elements depend on the type of material and the geometry of the material,multilayer structures with different geometries are proposed.For this purpose,conventional multilayer thin films,multilayer thin film including zigzag structure(zigzag 1)and multilayer thin film including double zigzag structure(zigzag 2)of manganese nitride are considered to protect AISI 304 stainless steel against corrosion in salt solution.These multilayer coatings including zigzag structures are prepared by alternately using the conventional deposition of thin film and glancing angle deposition method.After deposition,the samples are placed in a furnace under nitrogen flux for nitriding.The cross sections of the structures are observed by field emission scanning electron microscopy(FESEM).Atomic force microscope(AFM)is used to make surface analyses of the samples.The results show that the multilayer thin films including zigzag structures have smaller grains than conventional multilayer thin films,and the zigzag 2 structure has the smaller grain than the other two samples,which is attributed to the effect of shadowing and porosity on the oblique angle deposition method.Crystallography structures of the samples are studied by using x-ray diffraction(XRD)pattern and the results show that nitride phase formation in zigzag 2 structure is better than that in zigzag 1 structure and conventional multilayer thin film.To investigate the corrosion resistances of the structures,electrochemical impedance spectroscopy(EIS)and potentiodynamic polarization tests are performed.The results reveal that the multilayer thin films with zigzag structures have better corrosion protection than the conventional multilayer thin films,and the zigzag structure 2 has the smallest corrosion current and the highest corrosion resistance.The electrical impedances of the samples are investigated by simulating equivalent circuits.The high corrosion resistance of zigzag 2 structure as compared with conventional multilayer structure and zigzag 1 structure,is attributed to the high electrical impedance of the structure due to its small capacitance and high electrical resistance.Finally,the surfaces of corroded samples are observed by scanning electron microscope(SEM).
基金financially supported by the National Natural Science Foundation of China(Nos.U1706225,42006046,2019GGX102014,2019YFC0312103)the Research Fund of Open Studio for Marine Corrosion and Protection,Pilot National Laboratory for Marine Science and Technology(Qingdao,No.HYFSKF201804)。
文摘A Ag@CuFe_(2)O_(4)@TiO_(2) nanocomposite film with high performance of photogenerated cathodic protection was prepared by hydrothermal and photoreduction methods.The results showed that when the CuFe_(2)O_(4) hydrothermal reaction time was 6 h and the AgNO_(3) concentration was 0.1 M,the Ag@CuFe_(2)O_(4)@TiO_(2) nanocomposite material performed the best cathodic protection capability for 304 stainless steel(304SS).In this case,the protective potential achieved-930 mV(versus SCE)associated with the photocurrent density of 475μA/cm^(2),which was 14.8 times that of pure TiO_(2) nanowires.In the dark,the nanocomposite provided cathodic protection of up to 485 mV for 304SS.Due to the heterogeneous junctions at the two interfaces among the three kinds of nanocomposite materials,the build-in electric field was fabricated,which promoted the separation efficiency of photogenerated electrons and holes and effectively improved the photochemical cathodic protection of 304SS.
基金This work was supported financially by the Funding from the Taishan Scholarship of Climbing Plan(No.tspd20161006)the National Natural Science Foundation of China(No.51772176)the Scientific Research Foundation of Shandong University of Science and Technology for Recruited Talents(No.2017RCJJ018).
文摘Highly ordered Ag2 S/ZnS/ZnO nanorod array film photoanodes were prepared on a Ti substrate for photocathodic cathodic protection.The results indicated that the photoresponse range of the Ag2S/ZnS/ZnO composite film was extended compared to those of the ZnO and ZnS/ZnO films,indicating its higher light absorption capacity.When the Ag2S/ZnS/ZnO composite film served as a photoanode,the film can provide the best effective photocathodic protection for 304 stainless steel in a 3.5 wt%NaCl solution under white light illumination compared to the ZnO and ZnS/ZnO films.Additionally,in comparison to pure ZnO film,the photocurrent for the ZnS/ZnO film remained the same without noticeable fluctuation after illumination for 1 h,indicating that the ZnS functionalization improved the stability by overcoming the photocorrosion effect of the ZnO photoanode under light irradiation.
基金supported by the National Natural Science Foundation of China(Nos.51822402,51671044 and 52001051)the National Key Research and Development Program of China(Nos.2019YFA0209901 and 2018YFA0702901)+4 种基金the fund of the State Key Laboratory of Solidification Processing in NWPU(Grant No.SKLSP201902)the Liao Ning Revitalization Talents Program(XLYC1807047)the National MCF Energy R&D Program(No.2018YFE0312400)the Fund of Science and Technology on Reactor Fuel and Materials Laboratory(STRFML-2020-04)the China Postdoctoral Science Foundation(No.2020M670747).
文摘Bi_(2)WO_(6) nanoplate/TiO_(2) nanowire and Bi_(2)WO_(6) nanoflower/TiO_(2) nanowire composite films were successfully prepared using a hydrothermal method.The results show that the light absorption for Bi_(2)WO_(6)/TiO_(2) composite films is extended to the visible region after Bi_(2)WO_(6) nanoplates and nanoflowers are assembled onto TiO_(2) nanowires.Furthermore,Bi_(2)WO_(6) nanoflower/TiO_(2) nano wire composite film exhibits a better absorption property compared to Bi_(2)WO_(6) nanoplate/TiO_(2) nanowire film,which is mainly ascribed to the narrower bandgap of Bi_(2)WO_(6) nanoflower compared to that of Bi_(2)WO_(6) nanoplate.The photocurrent density for Bi_(2)WO_(6) nanoflower/TiO_(2) nanowire and Bi_(2)WO_(6) nanoplate/TiO_(2) nanowire composite films can reach 95 and 62.5 μA cm-2,respectively,which are much higher than that obtained for a pure TiO_(2) nanowire film(25 μA cm-2).Meanwhile,under illumination,the pure TiO_(2) nanowire,Bi_(2)WO_(6) nanoplate/TiO_(2) nanowire and Bi_(2)WO_(6) nanoflower/TiO_(2) nanowire films can reduce the potential of the coupled 304 stainless steel in 3.5 wt.%NaCl solution by 299,719 and 739 mV,respectively.Thus,Bi_(2)WO_(6) nanoflower/TiO_(2) nanowire film is found to provide the best effective photocathodic protection for 304 stainless steel.This work not only provides an example of shape-dependent photocathodic protection based on Bi_(2)WO_(6) but also opens up new possibilities to design an ideal microstructure on the basis of semiconductor materials for future applications of photocathodic protection.
基金supported by the Ministry of Science and Technology Project of China(2009, No. GJB20011)
文摘The protective behavior for a molten AZ91D alloy in an open melting furnace was investigated under a protective gas mixture containing 3% SO2 and 97% CO2, and the protection mechanism was discussed. Experimental results show that the gas mixture provides effective protection for AZ91D melt in the temperature range from 680 ℃ to 730 ℃. The microstructure, chemical composition and phase composition of the surface film formed on the molten AZ91D alloy were analyzed using scanning electron microscopy （SEM） with energy dispersive spectrometer （EDS） and X-ray diffraction （XRD）. The SEM results demonstrate that the surface films with an average thickness between 0.5 pm and 2 pm are dense and coherent in the protected temperature range. The EDS results reveal that the surface film mainly contains elements S, C, O, AI and Mg. The XRD results show that the surface film consists of MgO, MgS and a small amount of C phase.
文摘A kind of interlaminar film with carbon nanotubes inserted into polyether ketone with cardo was used for lightning strike protection of composite laminates. The distribution of the interlaminar film was investigated by experimental and numerical methods. Artificial lightning strike tests were conducted for 12-film carbon nanotube and traditional surface silver coating protected specimens. Then corresponding finite element models(FEMs) were established to analyze the lightning strike effect and validated by the experimental results. Based on the FEMs, the number, distribution and thickness of interlaminar film were investigated in order to obtain equivalent protection effect with the traditional surface silver coating. The results show that only the first two layers were damaged for the surface silver coating protected specimen, while 5 layers were ablated for the 12-film protected specimen. Lightning strike damage area of the laminate protected with 5-film carbon nanotube is almost the same as that of the laminate protected with 12-film carbon nanotube. Compared with traditional surface silver coating protection, one film protection with thickness of 360 lm can make the laminate to obtain equivalent damage depth, 54.8% smaller damage area and 58% less additional weight. And reparability of the laminate is better than that of the laminate protected with 5 interlaminar films.
